LED 硬灯条规格书

L11产品规格书产品概述应用环境：室内、户外产品尺寸图（单位：mm）L11线条灯是专为户外景观亮化设计的一款小功率LED 条形产品。

采用航空级6063挤压铝外壳，阻燃塑胶PC端盖，通过高导热耐候PU胶灌封防水；灯条体积小，外观精致；灯条间通过国标定制柔性线缆连接；产品长度、顔色可定制，能适应大曲线或曲面的安装；适用于建筑物立面轮廓勾边，内外表面装饰亮化。

产品特点：★新一代T T L串行技术设计★标准D M X512控制协议★行业领先的无线扣式防拽连接设计★高导热胶全灌封防水设计★户外防雷及静电（E S D）专用防护设计★产品的上盖可选：支持P C透明或乳白弧盖★产品采用独创的隐藏式安装滑块★支持R G B/W电流单独可调（低亮高灰）技术参数产品选型表基 本 参 数 色 彩/灰 度 RGB/W 各256级灰度； 光 源 类 型 3535 /5050 /2835 光 源 数 量48-72pcs/米 (0.25米-1米，长度可以按要求定制)材 质 铝喷涂外壳 / 阳极氧化 + 光学PC 罩寿 命 50,000h 重 量 710g/米 光 电 参 数 工 作 电 压 DC24V最 大 功 率 12-20W/米 RGB 光 强 180cd/米白 光 360cd/米 光 束 角 30° / 45° / 60° / 90° / 120°电 气 等 级 III 类其 它 参 数 工 作 温 度 -20°C to 50°C 储 存 温 度 -40°C to 70°C 防 护 等 级IP66配光曲线规格型号 光源 数量 光源类型 颜色控制类型 DC 工作电压 功率 白色 光强 DA028-48AT 48PCS 3535 RGB/W 单线串行TTL 24V 12W 120cd DA028-48AD 48PCS 3535 RGB/W DMX512 24V 12W 120cd DA028-48XD 48PCS 5050 RGBW DMX512 24V 15W 180cd DA028-48CN 48PCS 3535 2835 W 无控制 24V 12W 240cd DA028-60AT 60PCS 3535 RGB/W 单线串行TTL 24Vz 15W 150cd DA028-60AD 60PCS 3535 RGB/W DMX512 24V 15W 150cd DA028-60XD 60PCS 5050 RGBW DMX512 24V 20W 225cd DA028-60CN 60PCS 3535 2835 W 无控制 24V 15W 300cd DA028-72AT 72PCS 3535 RGB/W 单线串行TTL 24V 18W 180cd DA028-72AD 72PCS 3535 RGB/W DMX512 24V 18W 180cd DA028-72CN72PCS3535 2835W无控制24V18W360cd安装件外观尺寸安装底座尺寸图（单位mm）；固定式安装底座安装方式示意：①安装载体钻孔,装膨胀胶塞：在载体上按灯具安装位置做好记号，并钻孔(建议用6mm钻头）；把膨胀胶塞用锤子敲入钻孔里（注：胶塞不可松动）；②固定灯具安装底座：将灯具安装底座孔位对准膨胀胶塞孔，选用合适的自攻螺丝将灯具安装底座固定到安装载体上；③灯具安装：将灯具对准灯具安装底座，并扣到灯具安装底座上；④灯具加固,完成安装：装好灯具后，从侧下边打两个自攻螺丝将型材上盖与型材安装底座固定在一起，防止型材上盖坠落。

Date ：日期：1-8th Floor, Building #1,10th Industrial Zone, Tian Liao Community, Gong Ming Area, Guang Ming栋一至八楼Web/网址：Features 特征PLCC-2 Package. 垂直型表贴封装 Extremely wide viewing angle. 发光角度大Suitable for all SMT assembly and solder process. 适用于所有的SMT 组装和焊接工艺 Available on tape and reel. 适用于载带及卷轴 Moisture sensitivity level: 3. 防潮等级：3 Package:4000pcs/reel. 包装：4000颗/卷 RoHS compliant. RoHS 认证Description 描述The Blue source color devices are made with InGaN on Substrate Light Emitting Diode蓝光LED 由InGaN 三种元素芯片激发而成Applications 应用Optical indicator.光学指示 Indoor display.室内显示Landscape lighting,lamp belt. 景观照明，灯带等 General use.其他适合的应用Package Dimension外观尺寸：2.8*3.5*0.8mmNOTES:1.All dimensions units are millimeters. (所有尺寸标注单位为毫米)2.All dimensions tolerances are 0.2mm unless otherwise noted. (除特别标注外，所有尺寸允许公差为±0.2毫米)Electrical / Optical Characteristics at Ts=25°C 电性与光学特性Typical Optical Characteristics Curves典型光学特性曲线Fig.1-Forward Voltage Vs. Forward Current Fig.2-Forward Current Vs. Relative Intensity 伏安特性曲线正向电流与相对光强特性曲线备注All the parameters and standardsspecification are based on Refondtest platform.规格书中所有参数和标准都是基于瑞丰的标准测试平台。

LED灯带规格参数：上海升美电子LED灯带产品特色：1.采用优质超高亮LED发光二极管发光，具有耗电小(每个不到1W)、产生热量小、无眩光，寿命长、耐冲击等特点。

低电压直流12V，24伏供电，安全可靠性高。

2.颜色纯正柔和绚丽而且丰富多彩，有红黄蓝绿白七彩，还可按要求定制各种颜色或变换，全彩效果产品可配制控制器，三色和七彩互换。

3.寿命长，平均寿命达3万小时，免维护。

4.每三个LED即可组成一个回路，可以沿着上面切线任意截断，不损坏其它部分，又可无限度接长，可按客户要求定制各种长度的灯条。

5.采用非常柔软的PCB板为基板，可随意对接，弯曲，裁剪及任意固定在凹凸表面。

6.产品轻、薄，适合在窄小的空间里面安装。

7.由印制电路板组成，背面带双面胶，用于粘贴附著于固定物上。

上海升美电子LED灯带使用范围：广泛用于勾画具有标志性的建筑物大厦楼阁，桥梁，公园广场等轮廓的亮化工程，更成为点缀酒店，网吧，KTV, 洗浴中心，迪厅，夜总会等高档娱乐场所的靓丽风景线。

鉴于其亮度高，柔韧性好，可塑性强，色彩绚丽变化多样，个人DIY家居装饰，橱窗，时装表演，路径指示均可将之作为首选。

安装方法与注意事项：1、室内安装：LED灯带用于室内装饰时，由于不必经受风吹雨打，所以安装就非常简单。

以光虹电子生产的LED灯带为例，每款LED灯带的背后都贴有自粘性3M双面胶，安装时可以直接撕去3M双面胶表面的贴纸，然后把灯条固定在需要安装的地方，用手按平就好了。

至于有的地方需要转角或者是长了怎么办？很简单，LED灯带是以3个LED为一组的串并联方式组成的电路结构，每3颗LED即可以剪断单独使用。

2、户外安装：户外安装由于会经受风吹雨淋，如果采用3M胶固定的话，时间一久就会造成3M胶粘性降低而致使LED灯带脱落，因此户外安装常采用卡槽固定的方式，需要剪切和连接的地方，方法和室内安装一样，只是需要另外配备防水胶，以巩固连接点的防水效果。

3、电源连接方法：LED灯带一般电压为直流12V，因此需要使用开关电源供电，电源的大小根据LED灯带的功率和连接长度来定。

LED硬灯条产品说明书一、产品说明颜色:黄,白,暖白光工作电压: DC 24V灯珠分类：SMD5050(贴片5050灯珠)1、规格:5050每米40灯DC 24V 1M≤8 W；5050每米60灯DC 24V 1M≤12W ；5050每米72灯DC 12V 1M≤14.4 W；光源色温不同,光色也不同色温在3300K以下,光色偏红给以温暖的感觉；有稳重的气氛，温暖的感觉.，通称暖色温。

色温在 3000--6000K 为中间，人在此色调下无特别明显的视觉心理效果，有爽快的感觉；故称为“中性”色温色温超过 6000K ，光色偏蓝，给人以清冷的感觉，通称冷色温2、工艺类别NK---裸板（室内用）铝---滴胶（半防水，灯脚滴硅胶，工艺稍复杂）铝---全滴胶（防水，室外用，工艺稍复杂，适合室外复杂环境工作）产品特性1、采用散热性能好的铝基板或玻纤板作为载体，印制电路板，散热性能好，导电性强。

2、外壳为铝合金材料，散热性能好。

如果安装在室外，可根据客户要求把铝合金外壳氧化成跟楼体相同的颜色，不会因为安装灯具而影响楼体的美观。

3、采用防紫外线，抗老化的胶水全部密封，防水性能达到IP65。

4、一般应用于广告装饰、城市亮化、楼宇亮化、酒柜、珠宝展柜、天花暗槽等室内外照明以及装饰照明。

长度可按要求定做。

3、使用及注意：本产品为恒流低压12V，请接12V低压或购置变压开关电源；本品常规使用时，建议并联；当串联使用时，连接长度请勿超过电源最大功率的80%，以免电源超负载工作导致电源烧毁。

二、使用说明：1、接线说明：红、黄、蓝、绿、白单色防水软光条：产品引出两根电源线，一根是红色，一根是黑色，导线线径是22AWG，长度是150MM。

红色线接电源正级，黑色线接电源负极。

如果使用控制器控制，红色线接控制器输出的正级，黑色接控制器输出的负极。

2、安装说明：方案一：将灯条放到需要安装的位置上，取出螺丝，在灯条的两端堵头上上紧螺丝，固定好灯条，如左下图所示；方案二：卡件安装。

样品承认书SPECIFICATION FOR APPROVAL 客户名Customer品名 Product Name编号 Version number发出日期Deliver date制造确认 Product confirm and sign照明工程部照明品质部审核APPROVED BY APPROVED BY APPROVED BY检查結果□ 合格□不合格INSPECT RESULT ACCEPT REJECT客户确认Customer confirm and sign检查审核承认TESTED BY CHECKED BY APPROVED BY检查結果□ 合格□不合格INSPECT RESULT ACCEPT REJECT说明 REMARK:确认后请回传 , 谢谢 !Please confirm and fax to us ,thank you!产品规格书XL-5050LED硬灯条产品效果展示：产品名称： LED 软灯条产品型号： XL5050-60LED 硬灯条5050 灯珠效果LED 硬灯条5050 灯珠效果一、特点：1、采用高亮度SMD5050 LED灯珠，铝合金外壳，每三个LED为一段。

2、每条的标准长度为1M，每条灯珠数量分别有30PCS/M LED 灯珠，60PCS/M LED灯珠，72PCS/M LED灯珠3、发光颜色：红/ 绿 / 蓝 / 黄 / 白 / 暖白和长彩等多种颜色可供选择4、工作电压：DC12V/DC24V两种5、防水型SMD灯条，表面采用灌胶二、用途：1、 SMD高亮度硬灯条适用于酒店，超薄灯箱，KTV娱乐场所等室内装饰。

2、用于广告招牌等精品装饰领域。

3、度假装饰照明灯，显示及展览。

4、商场专柜，珠宝，首饰台及名贵钟表柜台。

三、产品规格：1 米 30 珠型号规格产品规格书型号颜色XL-5050-30-R 红XL-5050-30-G 绿XL-5050-30-B 蓝XL-5050-30-Y 黄XL-5050-30-W 白XL-5050-30-WW 暖白XL-5050-30-RGB RGB1 米 60 珠型号规格型号颜色XL-5050-60-R 红XL-5050-60-G 绿XL-5050-60-B 蓝XL-5050-60-Y 黄XL-5050-60-W 白XL-5050-60-WW 暖白XL-5050-60- RGB RGB1 米 72 珠型号规格型号颜色XL-5050-72-R 红XL-5050-72-G 绿XL-5050-72-B 蓝XL-5050-72-Y 黄XL-5050-72-W 白XL-5050-72-WW 暖白XL-5050-72- RGB RGB产品名称： LED 软灯条产品型号： XL5050-60 电压数量功率DC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2WDC12V 30/M 7． 2W电压数量功率DC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4WDC12V 60/M 14． 4W电压数量功率DC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2WDC12V 72/M 17． 2W四、参数序号项目 item 单位参数范围 Parameter range1 工作环境温度 working environment ℃-40~502 储存条件 storage condition ℃-50~604 额定电压 limited voltage V DC125 工作电流 current mA 206 功耗 Input power W 7． 2W / 14.4W / 17.2W灯珠类型号：SMD 5050 LED可选颜色：红/绿/蓝/黄/白/暖白/RGB发光角度 : 120 度灯珠数量:30PCS / M60PCS / M72PCS / M外形尺寸 : 1000*10*2mm按整体封存装:裸板V 型槽U 型槽硬灯条套 V 型槽图示硬灯条裸板图示U型槽图示五、注意事项：六、产品应用应用家居装饰应用 KTV 装饰珠宝柜装饰●使用说明 use manual:1. 请先仔细阅读产品规格书 ,确认其使用环境是否符合规格书上的条件上,方可放心使用 . Please read the specificationfirst to make sure the using condition is fit2. 将产品接入电源时 ,请先确保开关处于闭合状态 ..Please shut off the switch before connect the product, then turn on3.本产品保质期为一年 This product warranty for one year。

DESCRIPTIONzThe Green source color devices are made with Gallium Phosphide Green Light Emitting DiodeFEATURESz Low power consumptionz Popular T-1 3/4 diameter package z General purpose leads z Reliable and ruggedz Long life - solid state reliability z Available on tape and reel zRoHS compliantAPPLICATIONSz Status indicator z Illuminatorz Signage applicationsz Decorative and entertainment lightingzCommercial and residential architectural lightingPACKAGE DIMENSIONSL-7113LGDT-1 3/4 (5mm) Solid State LampSELECTION GUIDENotes:1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.2. Luminous intensity / luminous flux: +/-15%.3. Luminous intensity value is traceable to CIE127-2007 standards.Part NumberEmitting Color (Material)Lens TypeIv (mcd) @ 2mA [2] Viewing Angle [1]Min.Typ.2θ1/2L-7113LGD■ Green (GaP)Green Diffused 1.2 30°3 Notes:1. All dimensions are in millimeters (inches).2. Tolerance is ±0.25(0.01") unless otherwise noted.3. Lead spacing is measured where the leads emerge from the package.4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.Ki n g b ri g ELECTRICAL / OPTICAL CHARACTERISTICS at T A =25°CParameterSymbol Emitting ColorValueUnit Typ. Max. Wavelength at Peak Emission I F = 2mA λpeak Green 565 - nm Dominant Wavelength I F = 2mA λdom [1] Green 568 - nm Spectral Bandwidth at 50% Φ REL MAX I F = 2mA Δλ Green 30 - nm CapacitanceC Green 15 - pF Forward Voltage I F = 2mA V F [2] Green 1.9 2.25 V Reverse Current (V R = 5V) I R Green -10 μA Temperature Coefficient of λpeak I F = 2mA, -10°C ≤ T ≤ 85°C TC λpeak Green 0.1 - nm/°C Temperature Coefficient of λdom I F = 2mA, -10°C ≤ T ≤ 85°C TC λdom Green0.06 - nm/°C Temperature Coefficient of V F I F = 2mA, -10°C ≤ T ≤ 85°CTC VGreen-1.8-mV/°CNotes:1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )2. Forward voltage: ±0.1V.3. Wavelength value is traceable to CIE127-2007 standards.4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.ParameterSymbol Value Unit Power Dissipation P D 62.5 mW Reverse Voltage V R 5 V Junction Temperature T j 110 °C Operating Temperature T op -40 to +85 °C Storage Temperature T stg -40 to +85°C DC Forward Current I F 25 mA Peak Forward CurrentI FM [1]140 mA Electrostatic Discharge Threshold (HBM) -8000 V Lead Solder Temperature [3] 260°C For 3 Seconds Lead Solder Temperature [4]260°C For 5 SecondsThermal Resistance (Junction / Ambient) R th JA [2] 600 °C/W Thermal Resistance (Junction / Solder point) R th JS [2]350°C/WABSOLUTE MAXIMUM RATINGS at T A =25°CNotes:1. 1/10 Duty Cycle, 0.1ms Pulse Width.2. R t h JA ,R t h JS Results from mounting on PC board FR4 (pad size ≥ 16 mm 2 per pad).3. 2mm below package base.4. 5mm below package base.5. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.Ki n gb ri g htTECHNICAL DATAGREENRECOMMENDED WAVE SOLDERING PROFILENotes:1. Recommend pre-heat temperature of 105°C or less (as measured with a thermocoupleattached to the LED pins) prior to immersion in the solder wave with a maximum solder bath temperature of 260°C2. Peak wave soldering temperature between 245°C ~ 255°C for 3 sec (5 sec max).3. Do not apply stress to the epoxy resin while the temperature is above 85°C.4. Fixtures should not incur stress on the component when mounting and during soldering process.5. SAC 305 solder alloy is recommended.6. No more than one wave soldering pass.PACKING & LABEL SPECIFICATIONSPRECAUTIONSStorage conditions1. Avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature.2. LEDs should be stored with temperature ≤ 30°C and relative humidity < 60%.3. Product in the original sealed package is recommended to be assembled within 72 hours of opening. Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85 ~ 100°C.2. When soldering wires to the LED, each wire joint should be separately insulated with heat-shrink tube to prevent short-circuit contact.Do not bundle both wires in one heat shrink tube to avoid pinching the LED leads. Pinching stress on the LED leads may damage the internal structures and cause failure.3. Use stand-offs (Fig.1) or spacers (Fig.2) to securely position the LED above the PCB.4. Maintain a minimum of 3mm clearance between the base of the LED lens and the first lead bend (Fig. 3 ,Fig. 4).5. During lead forming, use tools or jigs to hold the leads securely so that the bending force will not be transmitted to the LED lens and its internal structures. Do not perform lead forming once the component has been mounted onto the PCB. (Fig. 5 )LED Mounting Method1. The lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement.Lead-forming may be required to insure the lead pitch matches the hole pitch.Refer to the figure below for proper lead forming procedures.Note 1-3: Do not route PCB trace in the contact area between the leadframe and the PCB to prevent short-circuits." ○" Correct mounting method " x " Incorrect mounting methodKi g b htLead Forming Procedures1. Do not bend the leads more than twice. (Fig. 6 )2. During soldering, component covers and holders should leave clearance to avoid placing damaging stress on the LED during soldering. (Fig. 7)3. The tip of the soldering iron should never touch the lens epoxy.4. Through-hole LEDs are incompatible with reflow soldering.5. If the LED will undergo multiple soldering passes or face other processes where the part may be subjected to intense heat, please check with Kingbright for compatibility.PRECAUTIONARY NOTES1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer tothe latest datasheet for the updated specifications.3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. Ifcustomer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threateningliabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance.5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.6. All design applications should refer to Kingbright application notes available at https:///application_notesKi n g b ri g ht。

Part Number Emitting Color Emitting MaterialLens-colorWavelength CIE127-2007*nm λPViewing Angle 2θ 1/2Luminous Intensity CIE127-2007* (I F =20mA) mcd *Luminous intensity value and wavelength are in accordance with CIE127-2007 standards.ATTENTIONOBSERVE PRECAUTIONSFOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICESESD-protected work areas to reduce static build up during assembly process (Reference JEDEC/JESD625-A and JEDEC/J-STD-033)Features● Ideal for indication light on hand held products ● Long life and robust package ● Standard Package: 2,000pcs/ Reel ● MSL (Moisture Sensitivity Level): 3 ● Halogen-free ● RoHS compliantLED is recommended for reflow soldering and soldering profile is shown below.Spatial DistributionThe device has a single mounting surface. The device must be mounted according to the specifications.Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1)Tape Specification (Units : mm)Remarks:If special sorting is required (e.g. binning based on forward voltage, Luminous intensity / luminous flux, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm2. Luminous intensity / luminous flux: +/-15%3. Forward Voltage: +/-0.1VNote: Accuracy may depend on the sorting parameters.Reel Dimension (Units : mm)PACKING & LABEL SPECIFICATIONSTERMS OF USE1. Data presented in this document reflect statistical figures and should be treated as technical reference only.2. Contents within this document are subject to improvement and enhancement changes without notice.3. The product(s) in this document are designed to be operated within the electrical and environmental specifications indicated on the datasheet. User accepts full risk and responsibility when operating the product(s) beyond their intended specifications.4. The product(s) described in this document are intended for electronic applications in which a person’s life is not reliant upon the LED. Please consult with a SunLED representative for special applications where the LED may have a direct impact on a person’s life.5. The contents within this document may not be altered without prior consent by SunLED.6. Additional technical notes are available at https:///TechnicalNotes.asp。

Led硬灯条定义：led硬灯条是指把LED芯片组装在PCB硬板上，又因其形状酷似带子，因此称为led硬灯条。

组装形式：led硬灯条采用PCB作为电路板，采用LED贴片进行组装，或者采用直插式进行组装，两者之间存在区别：贴片式较稳定，不容易脱落，保证LED芯片能正常使用；而直插式简单方便，但是排列不是很整齐，容易脱落，导致芯片损坏。

常用电压：一般硬灯条有分为低压灯条和高压灯条两种，低压灯条采用DC12-24V的电压，而高压灯条采用220V通用电压，这两者之间存在哪些区别？1、从产品使用安全来说：低压硬灯条的安全性更安全，使用的是低于人体安全电压的DC12-24V直流输入，安全用电，不存在安全隐患；而高压硬灯条采用220v电压，属于安全用电范畴，但是不小心的话，是存在安全隐患的。

2、从安装使用方面来说：由于低压灯条采用的是低压直流输入，在安装时，必须要使用电压转换器，另外还需要根据安装的长度来需要多少个变压器；而高压硬灯条直接接通家庭用电，即可使用，相对而言，方便简单。

3、从产品包装方面来说：低压硬灯条一般是5-10米一卷，要是更长，会大大影响到led 硬灯条的正常使用；而高压硬灯条来说，一般可以做到50-100米的长度，所接电压可以承受。

4、从产品的使用寿命来说：低压硬灯条热量小，散热快，很大程度确保了led硬灯条的使用寿命，一般使用寿命长达35000-50000小时；而高压硬灯条由于所散发的热量大，大大减少了它的使用寿命。

5、从产品价格来说：led硬灯条在使用中需要用到驱动电源和变压转换器，并且，使用的长度越长，价格越高；而led软灯条直接接通电源，可以带动50-100米的灯条，在使用电源上老说，低压的费用比高压的贵。

6、从产品的使用范围来说：低压硬灯条的使用率远远大于高压硬灯条，低压硬灯条使用面积广。

常用规格：一般常用的硬灯条规格有这几种（以下两种为常用规格）：1、3528led硬灯条：指的是长35mm和宽28mm，形状似长方形。

SM16703 IC（5050）灯条规格书一米10段60灯LED全彩灯条又名LED幻彩灯条，LED数码灯条，像素灯条，英文名为：LED pixel strips，产品为柔性FPC(软灯条板)/PCB(硬灯条板)为基板焊接LED，以及外围电路形成，可以实现追逐，流水，幻彩，显示效果等，主要用于KTV，酒店，家庭等等地方的装饰.SM16703全彩灯条采用一个IC六个灯,俗称”一拖六”,IC为SM16703,灯珠是5050RGB灯珠.工作电压为24V直流电压,配备24V全彩控制器可实现渐变/跳变，单/多跑马变，流水/追逐变，流星/快闪,单色变/混和变等等各种效果模式！灯带带有智能IC芯，可通过全彩控制器或带有编程的，达到任何想要的效.*产品规格*产品名称: 10段60灯灯珠型号: 5050RGB内置IC灯珠型号: SM16703工作电压: 24V功率：±18W/米灰度等级：256数据传输速率：800K/S工作温度：-40°C---80°C工作寿命：30Kh灯珠数量: 60灯/米IC数量: 10个IC/米（集成到了灯珠外部）10个像素点/米发光颜色：全彩/通过控制器控制能实现任意颜色任意效果（可定制其他单色跑马）点间距：板宽：12MM板底颜色：白板 / 黑板防水等级与重量：裸板-不防水 -滴胶防水-IP65 -套管防水-IP66 -灌胶防水-IP68 -包装：5米/盘卷盘固定防静电袋包装裸板-不防水：两端出三并对插接头外加双色电源线；背面贴3M强力双面胶；5米/盘，卷盘固定静电袋包装出货滴胶防水-IP65：表面覆盖一层透明防护硅胶；两端出三并对插接头外加双色电源线；背面贴3M强力双面胶；5米/盘，卷盘固定静电袋包装出货套管防水-IP65：将灯条置入360度全方位保护的硅胶套管内部；两端堵头堵死出三并对插接头外加双色电源线；5米/盘，卷盘固定静电袋包装出货灌胶防水-IP68：全方位保护的硅胶套管内部再注满透明硅胶；两端堵头堵死出三并对插接头外加双色电源线（也可出特制的防水对插接头）；5米/盘，卷盘固定静电袋包装出货*产品优点*1、比传统的单色灯条更漂亮、色彩更绚丽。