雨燕维修手册(英文)-上_部分3

Amarillo Double Reduction Fan Drives, if properly installed and maintained,should provide years of service with a minimum amount of maintenance.Repairs, when required, usually involve bearing or gear replacement. Whilethe job is not difficult, it should only be performed in an adequately equippedshop by capable personnel. It should be noted that any repairs made outsidethe factory on new drives without the consent of the manufacturer will voidthe warranty.Catalog DRR 6/09Post Office Box 1789 • Amarillo, Texas 79105 • 2401 Sundown Lane (79118) 806•622•1273 • FAX 806•622•3258 email:*********************© AGC 2009DOUBLE REDUCTION FAN DRIVES INSTRUCTIONS FOR REPAIRING Amarillo®Amarillo Gear Company®- ATTENTION -Please note that gear drives with a serial number above 231989 have all joints sealed with Loctite Gasket Eliminator 515 instead of gaskets. Loctite 515 is a formed in place gasket material, which provides superior sealing over conventional gaskets. After disassembly for repair or inspection, we recommend resealing with Loctite 515. However, gaskets may still be used. If a gasket is utilized between the horizontal carrier and the gear case for a gear drive originally built with Loctite, the flange thickness of bearing bushing (20) or hardened washer (201), if applicable, will have to be changed to maintain the proper position of the horizontal gear. To correct the horizontal gear position, increase the horizontal spacer thickness by the thickness of the gasket. If Loctite is used to re-seal the gear drive then no changes are required to the horizontal spacer.TABLE OF CONTENTSPage1.0. General Disassembly Instructions (1)2.0. Disassembly of Input Shaft Assembly (5)2.2. Models 1008 and 1110 (5)2.3. Models 1311, 1712, 1712.5 and 1713 (8)3.0. Disassembly of Intermediate Shaft Assembly (8)4.0. Disassembly of Output Shaft Assembly (8)5.0. General Assembly Instructions (10)6.0. Assembly of Output Shaft Assembly (10)7.0. Assembly of Intermediate Shaft Assembly (10)8.0. Assembly of Input Shaft Assembly (11)8.2. Models 1008 and 1110 (11)8.3. Models 1311, 1712, 1712.5 and 1713 (12)9.0. Installation of Assemblies into Gear Case (12)10.0. Adjustment of the Input Shaft Bearings (13)11.0. Backlash Check (13)12.0. Spiral Bevel Tooth Contact Pattern Check (16)13.0. Adjustment of the Intermediate Shaft Bearings (16)14.0. Adjustment of the Output Shaft Bearings (16)15.0. Completion of Assembly (17)16.0. Disassembly of the Oil Pump (17)17.0. Assembly of the Oil Pump (17)18.0. Disassembly of the Input Stem Pinion Assembly (19)19.0. Assembly of the Input Stem Pinion Assembly (19)20.0. Spiral Bevel Tooth Contact Pattern and Adjustment (20)21.0. Spiral Bevel Backlash Adjustment (20)22.0 Shaft Seals (23)Tables:1. Center Distance (1)2. Lift Point (1)3. “C” Values (15)Figures:1 Models 1008 and 1110 (2)2 Models 1311, 1712, 1712.5 and 1713 (3)3 Strong Back (4)4 1008 Horizontal Assembly (6)5 1110 Horizontal Assembly (7)6 Horizontal Assembly Without Gear Retainer (7)7 Horizontal Assembly With Inner Spacer (9)8 Horizontal Stem Pinion Assembly (9)9 Backlash Check (14)10 Oil Pump Assembly (18)11 Horizontal Stem Pinion Assembly (19)12 Correct Tooth Contact Pattern (21)13 Profile Error (21)14 Cross Contact (22)15 Shaft Angle Error (22)16 Input Shaft Seals (23)17 Output Shaft Seals (23)1712 1712.51712 1712.5MODEL 1311, 1712, 1712.5 & 17131712, 1712.5 and 17131712, 1712.5 and 1713 the slinger is mounted as shown in Fig. 7.1712, 1712.5 and 1713, the1712, 1712.5 and 1713, the(603) has started squarely into the bearing carrier in the gear case and has not cocked.10082.875 2.556 2.556 2.375 2.333 2.083 1.918 1.772 1.64511103.8573.5003.4542.9422.7502.4882.3032.1251.955131117121712.51713RATIO6.7:17.5:1 8:1 8.7:1 9:1 9.5:110:1 11:1 12:1 13:1 14:1 15:1 16:1 16.5:1 16.875:1 17:1 18:1 18.5:1 19:1 20:13.3753.0002.7502.5852.4002.2502.0663.7603.5123.1152.7862.6802.4832.3332.1022.0621.8563.7283.1152.7862.4832.3332.1413.7283.1152.7862.4832.3332.141should20.0.20.1.20.2.20.2.1.20.2.2.20.2.3.20.2.4.20.3.20.3.1.20.3.2.20.3.3.20.4.20.4.1.20.4.2.21.0.21.1.21.2.21.3.21.4.20212220.0 SHAFT SEALS22.1. Input Shaft Seals.22.1.1. Refer to Fig. 17 during installation.22.1.2. Install seals (802) in the oil seal plate (16) so the springs will be toward the gear drive. Coat the lips of theseals with a thin film of grease, as specified in step 3.0.22.1.3. Install the seal plate (16) on the horizontal carrier (15). Use a shield to protect the seals from being cut bythe keyway in the shaft.22.1.4. Insert a grease fitting into one port on the seal plate (16) and fill the seals with grease until it emerges fromthe other port. Use Mobile Grease #28.22.1.5. Remove the grease fitting and install a plug in the bottom port.22.1.6. After testing the gear drive, wipe off any grease that may have been purged from the seals and install aplug in the top port.22.2. Output Shaft Seals22.2.1. Refer to Fig. 18 during installation.22.2.2. Install seals (815) in the vertical seal carrier (21) so the springs will be toward the gear drive. Coat the lipsof the seals with a thin film of grease, as specified in step 3.0.22.2.3. Install the seal carrier (21) on the vertical cover 12.22.2.4. Insert a grease fitting into one port on the seal carrier (21) and fill the seals with grease until it emerges fromthe other port. Use Mobile Grease #28.22.2.5. Remove the grease fitting and install a plug in the port.22.2.6. Pack the area above the top seal up to the shoulder of the shaft with grease.22.2.7. Apply a film of grease to the journal for the upper seal plate (11).22.2.8. Install the upper seal plate (11) and tighten the three set screws. Wipe off any grease that may have pushedout around the upper seal plate.22.2.9. After testing the gear drive, wipe off any grease that may have been purged from the seals and install a plugin the open port.Fig. 16Fig. 1723- ATTENTION -Please note that gear drives with a serial number above 231989 have all joints sealed with Loctite Gasket Eliminator 515 instead of gaskets. Loctite 515 is a formed in place gasket material, which provides superior sealing over conventional gaskets. After disassembly for repair or inspection, we recommend resealing with Loctite 515. However, gaskets may still be used. If a gasket is utilized between the horizontal carrier and the gear case for a gear drive originally built with Loctite, the flange thickness of bearing bushing (20) or hardened washer (201), if applicable, will have to be changed to maintain the proper position of the horizontal gear. To correct the horizontal gear position, increase the horizontal spacer thickness by the thickness of the gasket. If Loctite is used to re-seal the gear drive then no changes are required to the horizontal spacer.Post Office Box 1789 • Amarillo, Texas 79105 • 2401 Sundown Lane (79118) 806•622•1273 • FAX 806•622•3258 email:********************* © AGC 2009Amarillo Gear Company ®A Marmon Water/Berkshire Hathaway Company。

篇一：雨燕保养使用手册2013雨燕车主保养使用手册时尚外形的小车可以说是日系车中的擅长领域，Swift雨燕便是于2004年巴黎车展中正式亮相的小型车款。

自04年11月日本上市开始后，去年陆续在中国、匈牙利、印度等地上市，成为不折不扣的铃木世界战略小车。

良好的经济性受到了不少车友的追捧。

但也有部分车友对雨燕引擎、动力方面的表现持否定的观点。

在此收集整理出众多雨燕车主在实际使用感受中对雨燕的优缺点的评价，能客观的反映出雨燕的优势和不足，给所有喜爱雨燕的车友一个参考。

雨燕保养以及使用细节一、走合保养期新车里程在最初的0－100公里时，发动机等运动件表面还较粗糙，其内摩擦阻力大，如不控制车速、负荷、温度，机件就会发生急剧的磨损。

因此，在最初的1000－2000公里磨合期内，必须严格按规定行驶。

磨合良好的汽车，其使用寿命、可靠性及经济性将大大提高。

磨合保养期内基本规范要求：1、不能以最大油门过度行驶（建议车速60－80公里／小时）；2、各档发动机转速均不能超过最高转速的3／4；3、汽车最好不要满载；4、经常使用不同档位，以利于各零部件之间的均匀磨合；5、磨合后期可将车速逐渐提高到最高允许速度（各档位车速范围见使用手册）；6、出现任何异常现象，立即向专门人员请教。

注意：磨合后期（1500-2500公里），必须到就近的长安铃木特约维修站进行首次强制保养！以后视情况每6000-10000公里进行一次例行保养。

二、出车前的准备起动前1、检查汽车有无漏水、漏油现象；2、检查机油油位及清洁度；3、检查发动机冷却液、制动液、洗涤液液位（必要时添加）；4、检查皮带张紧度（必要时调整）；5、检查轮胎气压及磨损状况。

起动汽车后1、检查仪表、信号灯、操纵开关是否正常；2、检查发动机及运动附件是否正常，有无异响；3、汽车怠速是否正常。

注意：用户自己在保养车辆时请仔细阅读随车使用手册！三、行驶中注意事项1、冷机起动后，应让发动机预热3－5分钟，最初以中、低速行驶，发动机水温正常后才能高速行驶；2、从经济性及发动机寿命、环保等方面考虑要尽量使用高档行驶，因为此时在同样车速下，发动机的转速最低；3、当车下陡坡或长坡时，要挂上适当的低速档，用发动机辅助制动。

Maintaining Guide Manualof the Air Disc BrakeContentCATALOGUE1. Summarize2. Maintaining description2.1 Safety briefing during maintaining2.2 Breaking function check2.2.1 Clearance check2.2.2 Adjuster check2.3 Brake pads check2.4 Rotor check3. Brake pads replacement4. Brake replacement5. Dust cap replacement5.1 Dust cap & bushing replacement5.2 Screw dust cap replacement6. Rotor check/replacement6.1 Rotor check6.2 Rotor replacement7. Brake chamber replacement7.1 Brake chamber removal7.2 Brake chamber installation8. Adjuster replacement9. Troubleshooting10. Exploded view11. List of mounting & maintaining toolsBrief introduction of YOUFINYOUFIN was established on May 20th, 1998. It is a Sino-Foreign joint-venture enterprise registered in Wuhan Economic and T echnological Development Zone with multi-investors among which private investors dominate. It is a professional company engaged in manufacturing disc brakes and serving the principal automobile manufacturers by providing modularized supply. The main prod ucts cover hydraulic disc brakes and air disk brakes in close to thirty sizes.YOUFIN developed the air disc brake autonomously and patented the product. So far we are the only manufacturer in China that can mass produce air discs to be used in long distance coaches and inner city buses. It is evaluated that the quality of our products is close to the advanced international level in field use. The product development is part of the National T orch Plan and is also sponsored by the Small and Medium-sized Enterprise T echnical Innovation Foundation of Chinese Ministry of S&T.Our Air Disc Brake products are on an absolute leading position in China and the same international level as far as the key technology is concerned.1. SummarizeYOUFIN Air Disc Brake has four sizes (16’’, 17.5’’19.5’’, 22.5’’). It can satisfy different vehicles. The brakes have compact structure; automatically wear compensation and can easily changing the brake pad.2. Maintaining descriptionSafety briefing during maintainingIt’s most important to ensure safety driving and breaking by goodcharacteristics of the brake.Observe brake pad and rotor wear limits. When they warned already to assigned smallest thickness, it need replace immediately, otherwise, it may cause the accident. The pads scorches, grinds or greases must replace immediately.Every pad on each bridge must replace at the same time.When services the brake, the vehicle must park in smooth gound and the wheel withstand with the block/ stone prevent rolls.Note:●Must guarantee it does not occur with careless brake. When replace brakepad don’t make the brake, otherwise, it will hurts the body!●Do not use the compressed air or other cleaning up equipment clean thebrake, in order to avoid injures the body.●Be sure your hands and fingers place outside the caliper, in order to avoidinjures the body.●When moves and installs the brake should have some assistance, avoids ittoo heavy to hurts the body.●When take off the brake to make maintenance, it must fix on the clamp withhigh strength bolt, in order to avoid hurts the body.●Only allowed genuine YOUFIN kits and pads permitted by YOUFIN. Duringthe first 50 miles driving after new pad replacement, should avoid promptlybrake and brake at a long distance, Prevent overhigh temperature.●Allowed genuine YOUFIN kits and brake pads permitted by YOUFIN.●Only can use the recommendation kits in service. Screws the bolt/nutaccording to the request moment of force.Brake Function checkClearance checkProcess:●T ake off the hexagon bolt (39), loosen the pad retainer (38).●Remove pad retainer (38) from caliper.●Remove 3pcs of pad clip (37).●Move the cable (40) to the side.●Push the caliper towards the wheel and check the clearance with tune-upgauge.0.5mm ≤ clearance ≤ 1.2mmNote: Insert tune-up gauge between the caliper (1) and the brake pad (35). Should check the adjuster while the clearance is out of standard.Adjuster checkProcess:●Remove the rubber cap (12).●Turn hexagon head (22) clockwise by wrench to ensure clearance larger than3mm. (Or remove the brake pad and the push board)Note:a. Need enough room (3mm<clearance) for turn adjuster preventing un-fit.b. Never force to adjust the hexagon head (22) and/or the adjuster!Push the pressure arm 5 times in small increments and observe the hexagon head (22). While the adjuster is in good condition, hexagon head (22) must rotate clockwise.c. As the regulated quantity increase, rotation angle decreases.If the adjuster hexagon head (22):a) Not running at allb) Only running at first pushc) Running, but stopped in the middleWhile considers adjuster failed. Y ou should replace the brake on the basis of section 4 or change the adjuster in accordance with section 8.●Keep the clearances at 1mm (section 3) after adjuster check is finished.●Reinstall the rubber cap (12).Brake pads wearing check●Scorches, grinds and greased brake pad must replaces immediately.●Brake pads at the same bridge must replace at the same time.●Brake pad and pad clip must replace at the same time.Rotor checkProcess:●Remove the brake pad according to section 3.●T est thickness of the rotor.Note: Observe the brake pads and the rotor attrition situation. Excessive attrition of the rotor and the brake pads will reduce their potency and causes the brake fail!CAUTION: Rotors on the same bridge must replace at the same time. Single side rotor replacement is unacceptable. Recommend installs new brake pads whilereplace the new rotors.Rotor Dimension limitsRotor jumpiness (↗) check:2.4.1 Process:●Installs division indicator on the bracket (dial guage).●Measure jumpiness (↗) through turns the wheel. Jumpiness (↗) should lessthan 0.15.●Replaces the rotor to satisfy the request of section 6.●Modified brake pad should fulfil the specific requirements in section 3.2.4.2 Rotor test:At each change of Pads check the Rotor for grooves and cracks.The diagram at the right shows possible conditions of the surface.A = Small cracks spread over the surface are allowedB = Cracks less than 0.02in. (0.5mm) wide, running in a Radial direction, are allowedC = Grooves (circumferential) less than 0.06in. (1.5mm) wide are allowedD = Cracks in the vanes are not allowed and the Rotor MUST BE REPLACED.a = Pad contact area3. Brake Pad replacementNote: Do not use the pipe spanner/ board die! Keep your hands and fingers outside the caliper avoid the hurts of body!Brake Pad dismantle process:●T ake off hexagon bolt (39) from the Pad Retainer with spanner.●Remove the pad retainer from caliper (1).●T ake off the pad clip (37), which is above the pads (35,36) and push board (19).●Remove the sensor on brake pad.●T ake off the push board (19) & the brake pads (35,36).●Adjust hexagon head to make tappet back to the initial position.●Clean the pad groove & push board and anchor surface with brush.Note: Don’t hurt the dust cap (5 & 10). Be sure of no grease on installation surface!●Check the adjuster on the basis of section 2.2.2.Note: Fix the key while checking & turning the adjuster cap to avoid screw rotate.●Check the rotor according to section 2.4.3.2 Brake pad installing process:●Need enough room between the caliper & the rotor to insert brake pad.●Insert push board (19) at the place the caliper combine with the adjust screw.Note: Push board must on the bracket supporting surface. Adjust screw pin must in groove. Otherwise it will do harm to Adjuster mechanism. Ensure the dust cap untwisted by rotate the adjust screw.●Insert the cable sensor to pad groove. Fix cable on bearing (40).Note: The sensor contactor must face the brake disc and installs at the correctposition. Attention the wire trend to prevents the friction.●Insert new pad (36) at side of the push board.●Push caliper toward the wheel until the pad touch the rotor.Insert the brake padat wheel side.Note: Don’t adjust hexagon head violently.Note: Turn the adjuster counter-clockwise to decrease the clearance between pads.Don’t install the retainer before adjustment.Note: Check the rubber cap (12), be sure it is correctly seated.4. Brake replacementNote: Don’t use pipe wrench. Ensure your hands and fingers outside the caliperavoid hurt your body!Note: The Brake will supplies in assembly.CAUTION: The left brake and the right brake cannot exchange. Arrow direction on the brake is same as the forward direction of the wheel.4.1 Brake removal process:●Remove brake pad (see Section 3).●Release nut on the caliper, take of brake chamber.●Remove brake assessment from the bridge.●Check brake pad on the basis of section 2.3.●Check rotor on the basis of section 2.4.4.2 Brake installing process:●Install the new brake over rotor on the bridge. Screwed bolt with the spanner.Note: The right install order of the bolt is screwed both side symmetry.●T ake down the flange protection cap on the brake chamber.Note:Air chamber installment position. Open the scupper faces the ground, and stops other mouths.●Install brake pad and push board on the basis of section 3.●Install the air chamber and tighten with spanner.●Adjust the clearance.5. Guide Pin dust cap replacementNote: Do not use the pipe spanner/ board die! Keep your hand & finger outside the caliper, in order to avoid injuries.Note: When replaces all dust cap of guide bushing, section 5.1 & 5.2 should unify to avoids repetitive work. Single bushing replacement according to 5.1 and 5.2 corresponding work orders.5.1. Dust cap & bushing replacement●T ake off the brake pad according to section 3.●Loosen the chamber bolt and remove the brake chamber from caliper.●Remove the caliper assessment from bridge.●T ake off the steel cap (11) from guide bushing (8 & 9) by suitable tools.Dismantle caliper (1) from the bracket (2).Note: Don’t hurt the hole, the lid while open the steel cap with tools.●Loosen the bolt (6 & 7); separate the caliper (1) from the bracket (2).Note: When caliper moves, it may hurt body.●Cleaning up the bracket bonding plane●Take off the guide pin (8&9) on caliper (1). Then remove the dust cap (5).●Presses out bushing 4 with mandril from caliper1.●Cleans up the guide pin hole of caliper.Installing process:●Long guide pin hole must press in two new bushings. Short guide pin holepress in one.●Guarantee the size in drawing.●Greases between them and the bushing●Install new dust cap in the guide pin hole.Note: Cleans up the guide pin hole and grease the edge of dust cap before install for easy installation. Ensure the dust cap installs steadily, without crease and inside the ring groove of the caliper.●Install long/short guide pin to each hole and dust cap upside set in guide pinring groove.●Put the caliper (1) on the bracket (2) and plug guide pin (8&9) in guide hole.●Plug new bolt (6&7) (long one for pin 8, short one for pin 9) and screwed onbracket (2) with spanner.Note: Assembly must be careful, don’t damage the dust cap (5). First, screws bolt on long pin (8), and then screws bolt on short pin (9).When service maintenance, remove the guide pin (8&9) and replace by new bolt (6&7)!●Move the caliper on guide pin (8,9) forward and backward to check whether thecaliper can move freely.●Put on new copper cap on caliper (1) hole and push it in with correct kits. Note: Avoids the hurts of surface.●Raising the guide pin dust cap (5) carefully for cancel the air pressure.●Install brake across the rotor on bridge. Screwed bolt with the spanner.Note: Correct install process of the hexagon bolt.●Install brake pads and adjust clearance. Implemented section 3, notice theexplanation.●Cleaning the install flange on caliper and grease inside the pressure arm ballsocket before reinstall the brake chamber.●Install the brake chamber and screwed with spanner.Note: After the installation of brake chamber, the lowest chamber hole face theground must open, other mouths stop up.5.2. Screw dust cap replacementNote: If only replace the screw dust cap, does not need to remove the caliper andthe air chamber.Process:●Remove brake pad and push board according to section 3.●Push the caliper towards to brake chamber.●T ake off screw dust cap (10) from the ring groove on adjust screw (21).●T ake down from dust cap base with screwdriver.●Check screw thread.●Turning the adjust bolt for 30mm clockwise with the spanner.●Inspection thread corrosion and whether is damaged.●Turning it clockwise, feeling its lubrication and check the adjust screw thread.●Clean the base of caliper dust cap (10). (Arrow pointed)●Push new dust cap (10) on adjust screw. Install it on the base with kits. Observes itinstalls whether arrived.●Grease on the edge of dust cap (10) and install it on the base of adjust screw (21).Note: Guarantees the dust cap steadily in place and does not have the corrugation in the adjust screw ring groove.Installation process:●Install the brake pad and adjust the clearance (see Section 3).6. Rotor check/replacement6.1 Rotor check Check the rotor (Section 2.4) If the rotor reached the minimumthickness, it must be replaced.6.2 Rotor replacementNote: Generally recommend use new brake pad while install new/machined rotor.6.2.1 Uninstall the rotor:●R emove the brake pad. (see section 3)●T ake off the brake chamber. (see section 7)●T ake down brake from bridge. (see section 4)●T ake off the wheel and the rotor.(Refer to V ehicle Manufacture’srecommendations)6.2.2 Rotor installation:●I nstall the wheel and rotor. (refer to V ehicle Manufacture’s recommendations)●D egrease the rotor.●T urn the wheel and check the installed rotor (Section 2.4).●A djust ABS sensor refer to V ehicle Manufacture’s recommendations.●I nstall the brake (see Section 4).●I nsert pad (see Section 3).●I nstall brake chamber (see Section 7).7. Brake chamber replacementNote: Don’t use pipe wrench! Ensure your hands and fingers outside the caliperavoid hurts body!Note: Can only use the chamber assigned by the Vehicle Manufacture.7.1. Brake chamber removal:●Bleeds off the compressed air.●Remove the upper air pipe of brake chamber.●Remove the chamber from caliper.7.2. Brake chamber installation:Note: According to the brake installment position, only can open the scupperunderneath.●Cleans the sealing plane of the pressure are ball socket (arrow) and caliper beforethe brake chamber installation.●Screwed the chamber mounting nut alternately with spanner in torque ratingrequired by the air chamber supplier.●Connection the air pipe.Note: Never twist the braking line, place it originally avoid fiction with other sets.While exist air leak, finds the leakage and check the connection.●Function and performance examination.8. A djuster replacement8.1 A djuster removal●Remove brake pad (see Section 3).●Remove brake chamber (see Section 7).●T ake off brake (see Section 4).●T ake off upper bolt by hexagon wrench.●Remove adjuster and other parts in the caliper.Note: Don’t hurt the screw dust cap.8.2 A djuster installation●Grease inside the caliper.●Put the return spring (18) at each side.●Install the needle assembly and the adjuster.●Puts the washer and top head, screwed the bolt with spanner according to theopposite angle principle.Note: Guarantee the bolt tighted the moment of force.9. Troubleshooting11. List of mounting & maintaining toolsYOUFIN is in the process of logo replacement, new logo will put into practice gradually. It with the original logo is still the YOUFIN’s product. Final interpret right for the logo belongs to YOUFIN.。

【大全】汽车维修手册大全好好收藏【关键字】大全汽车维修手册大全下载地址：上海通用别克陆尊维修手册F50日产风雅维修手册/sort03/sort0147/down-406.htmlC11颐达维修手册中文/sort03/sort0147/down-410.html2005 凯迪拉克XLR 维修手册/sort03/sort0147/down-415.html 2005 凯迪拉克CTS 维修手册/sort03/sort0147/down-416.html 柯斯达维修手册/sort03/sort0147/down-467.html丰田花冠维修手册/sort03/sort0147/down-471.html2007别克林荫大道维修手册/sort03/sort0147/down-499.html 奥迪A4维修手册免费下载/sort03/sort0147/down-781.html 别克维修手册/sort03/sort0147/down-784.html丰田花冠维修手册下载/sort03/sort0147/down-787.html景程维修手册/sort03/sort0147/down-851.html依维柯汽车维修手册/sort03/sort0147/down-1110.html东风雪铁龙赛纳轿车维修手册/sort03/sort0147/down-1111.html别克荣誉维修手册/sort03/sort0147/down-1112.html毕加索维修手册/sort03/sort0147/down-1113.html奥迪A6维修手册-下册/sort03/sort0147/down-1114.html奥迪A6维修手册-上册/sort03/sort0147/down-1115.html爱利舍维修手册/sort03/sort0147/down-1116.htmlA6维修手册2005年/sort03/sort0147/down-1117.html2005 凯迪拉克CTS 维修手册/sort03/sort0147/down-1118.html北京JEEP维修手册/sort03/sort0147/down-1119.html奥迪C6A6维修手册/sort03/sort0147/down-1124.html2003款AUDI A8中文维修手册/sort03/sort0147/down-一汽奥迪A6L维修手册2005（C6）/sort03/sort0147/down-1234.html 新皇冠维修手册/sort03/sort0147/down-1236.html 新广本维修手册/sort03/sort0147/down-1237.html新M3维修手册/sort03/sort0147/down-1239.html维修手册_丰田亚洲龙下/sort03/sort0147/down-1240.html维修手册_丰田亚洲龙上/sort03/sort0147/down-1241.html威驰维修手册/sort03/sort0147/down-1242.html上海雪佛兰乐骋維修手冊/sort03/sort0147/down-1245.html 上海大众高尔维修手册(2003) /sort03/sort0147/down-1246.html瑞风英文维修手册/sort03/sort0147/down-1248.html瑞风第三版发动机维修手册2006 /sort03/sort0147/down-1250.html瑞风第三版底盘维修手册2006 /sort03/sort0147/down-1251.html瑞风第二版发动机维修手册2006 /sort03/sort0147/down-1252.html日产FUGA(Y50)风雅维修手册/sort03/sort0147/down-1256.html普利马维修手册/sort03/sort0147/down-1258.html克莱斯勒土星原厂手册/sort03/sort0147/down-1262.html克莱斯勒彩虹原厂维修手册/sort03/sort0147/down-1264.html 凯迪拉克XLR /sort03/sort0147/down-1265.html花冠维修手册/sort03/sort0147/down-1266.html花冠NZE12.ZZE12维修手册/sort03/sort0147/down-1267.html国产奥迪A6、帕萨特全车维修手册/sort03/sort0147/down-1270.html丰田特锐修理手册-最终版 B /sort03/sort0147/down-丰田特锐修理手册-最终版 A /sort03/sort0147/down-1275.html丰田陆地巡洋舰3400维修手册（下册）/sort03/sort0147/down-1276.html丰田陆地巡洋舰3400维修手册（上册）/sort03/sort0147/down-1277.html2002款stream时韵维修手册/sort03/sort0147/down-1324.html04MY富士森林人原厂维修手册/sort03/sort0147/down-1325.html爱利舍维修手册/sort03/sort0147/down-1329.html东风雪铁龙赛纳维修手册/sort03/sort0147/down-1336.html 福特05款领航员维修手册/sort03/sort0147/down-1337.html 雷诺RENAULT维修手册/sort03/sort0147/down-1339.html 新皇冠原厂维修手册包括电路/sort03/sort0147/down-1346.html雪铁龙赛纳维修手册(电路图部分) /sort03/sort0147/down-1347.html一汽A6L维修手册2005（C6）/sort03/sort0147/down-1348.html翼豹维修手册中文版/sort03/sort0147/down-1349.html悦达千里马维修手册/sort03/sort0147/down-1350.html福克斯维修手册/sort03/sort0147/down-1352.html双龙爱腾SUV-ACTYON维修手册/sort03/sort0147/down-1355.html奇瑞东方之子维修手册(部分) /sort03/sort0147/down-1356.html奇瑞T11维修手册（瑞虎SUV）/sort03/sort0147/down-1357.html凯美瑞原厂维修手册06 /sort03/sort0147/down-1358.html嘉年华维修资料/sort03/sort0147/down-1360.html富士森林人05、06原厂维修手册/sort03/sort0147/down-1361.html丰田特锐维修手册/sort03/sort0147/down-1362.html东风雪铁龙凯旋电器手册-原厂2006-10 /sort03/sort0147/down-1364.html东风雪铁龙毕加索轿车维修手册/sort03/sort0147/down-1365.html大捷龙中文维修手册/sort03/sort0147/down-1367.html北京现代特拉卡T erracan维修手册/sort03/sort0147/down-1368.html宝来Bora A4维修手册/sort03/sort0147/down-1370.html一汽大众速腾维修手册/sort03/sort0147/down-1438.html丰田皇冠CROWN维修手册——原厂扫描2004 /sort03/sort0147/down-1439.html东南新菱帅台湾版JT(Virage) /sort03/sort0147/down-1440.html东南凌绅维修手册/sort03/sort0147/down-1441.html东风日产（骐达颐达）维修手册/sort03/sort0147/down-1444.html东风本田CR-V维修手册/sort03/sort0147/down-1447.html2006 ODYSEEY奥德赛维修手册/sort03/sort0147/down-1450.html2005 ODYSEEY奥德赛维修手册/sort03/sort0147/down-1451.html2002 ODYSEEY奥德赛维修手册/sort03/sort0147/down-1453.html欧洲汽车自动变速器维修手册/sort03/sort0147/down-1626.html夏利2000金夏利环保夏利轿车维修手册/sort03/sort0147/down-1632.html哈飞赛马全车维修手册/sort03/sort0147/down-1643.html奥迪A4 01V型自动变速器前轮驱动和全轮驱动维修手册/sort03/sort0147/down-1649.html 雪佛兰开拓者汽车维修手册/sort03/sort0147/down-1658.html夏利2000维修手册/sort03/sort0147/down-1661.html帕萨特B5维修手册/sort03/sort0147/down-1696.html中华轿车维修手册/sort03/sort0147/down-1701.html奇瑞QQS11维修手册/sort03/sort0147/down-1712.html奇瑞QQ6维修手册/sort03/sort0147/down-1713.html奇瑞A113维修手册/sort03/sort0147/down-1715.html凯迪拉克维修手册/sort03/sort0147/down-1716.html广州飞度轿车维修手册(1.3L) /sort03/sort0147/down-1717.html大众途安维修手册(英文版) /sort03/sort0147/down-1719.html 2007款凯美瑞原厂维修手册B（英文）/sort03/sort0147/down-1724.html 2007款凯美瑞原厂维修手册A （英文）/sort03/sort0147/down-1725.html2003雅阁Accord维修手册/sort03/sort0147/down-1726.html 丰田supra维修手册/sort03/sort0147/down-1732.htmlNISSAN全系列乘用车维修保养手册/sort03/sort0147/down-1745.html羚羊世纪星轿维修手册/sort03/sort0147/down-1972.html上海雪弗兰乐驰维修手册/sort03/sort0147/down-1973.htmlAQ015变速器维修手册/sort03/sort0147/down-2111.htmlb11东方之子维修手册/sort03/sort0147/down-2112.html保时捷968维修手册/sort03/sort0147/down-2114.html东方之子的变速箱维修手册/sort03/sort0147/down-2115.html 东南菱帅维修手册/sort03/sort0147/down-2116.html比亚迪F3维修手册/sort03/sort0147/down-2123.html湖汽_长丰猎豹汽车维修手册/sort03/sort0147/down-2130.html花冠维修手册/sort03/sort0147/down-2131.html吉利自由舰维修手册/sort03/sort0147/down-2132.html凯迪拉克维修手册/sort03/sort0147/down-2133.html轩逸维修手册/sort03/sort0147/down-2140.html雪佛兰开拓者汽车维修手册/sort03/sort0147/down-2141.html 起亚电路维修手册/sort03/sort0147/down-2192.html奔驰BENZS320维修手册/sort03/sort0147/down-2211.html 《A55 江淮瑞风维修手册》/sort03/sort0147/down-2218.html 1985款丰田卡车及四轮驱动汽油机车维修手册/sort03/sort0147/down-2224.html 东风雪铁龙毕加索轿车结构与维修/sort03/sort0147/down-2225.html凌志LS400维修手册/sort03/sort0147/down-2229.html帕萨特领驭空调维修手册/sort03/sort0147/down-3240.html欧宝电路维修手册/sort03/sort0147/down-3242.html雷诺风景维修手册/sort03/sort0147/down-3243.html奔驰S600维修手册/sort03/sort0147/down-3246.html保时捷卡宴维修手册/sort03/sort0147/down-3247.html07款新猎豹CS6车间维修手册/sort03/sort0147/down-4361.html东风悦达起亚福瑞迪/sort03/sort0147/down-4362.html比亚迪F3DS15-41型变速器结构图册/sort03/sort0147/down-4616.html比亚迪F3安全气囊维修手册/sort03/sort0147/down-4617.html比亚迪F3变速器维修手册/sort03/sort0147/down-4618.html 比亚迪F3车身附件维修手册/sort03/sort0147/down-4619.html比亚迪F3车身维修手册/sort03/sort0147/down-4620.html比亚迪F3外饰维修手册/sort03/sort0147/down-4621.html比亚迪F3维修手册/sort03/sort0147/down-4622.html丰田普瑞维亚PREVIA 维修手册/sort03/sort0147/down-6655.html07款三菱LANCER EVOLUTION IX 维修手册/sort03/sort0147/down-7089.html 2005年斯巴鲁翼豹维修手册中文版/sort03/sort0147/down-7098.html2006飞度FIT维修手册增补版/sort03/sort0147/down-7099.html99年NISSAN(Y61)维修手册/sort03/sort0147/down-7104.htmlNISSAN_日产骐达电子维修手册TIIDA(DFL7160) /sort03/sort0147/down-7105.html PASSATB5维修手册/sort03/sort0147/down-7106.htmlVOLVOS80维修手册/sort03/sort0147/down-7107.html北京现代途胜使用手册/sort03/sort0147/down-7108.html北京现代雅坤特使用手册/sort03/sort0147/down-7109.html昌河铃木北斗星维修手册/sort03/sort0147/down-7111.html长安CM8原厂维修手册/sort03/sort0147/down-7112.html长安福特嘉年华维修手册/sort03/sort0147/down-7117.html长安福特蒙迪欧维修手册/sort03/sort0147/down-7118.html朝阳柴油机_4102-c3a-c3b维修手册/sort03/sort0147/down-7128.html朝阳柴油机_4102C3C至C3G系列维修手册/sort03/sort0147/down-7129.html朝阳柴油机_电控发动机常见故障的检/sort03/sort0147/down-7130.html道奇锋哲Avenger中文维修手册/sort03/sort0147/down-7131.html东风雪铁龙凯旋原厂维修手册/sort03/sort0147/down-7134.html福特蒙迪欧维修手册/sort03/sort0147/down-7167.html广州本田飞度维修手册/sort03/sort0147/down-7169.html花冠Corolla 2004维修手册/sort03/sort0147/down-7173.html 卡迪拉克英文版维修手册/sort03/sort0147/down-7174.html凌志LS430电器维修手册/sort03/sort0147/down-7175.html 羚羊世纪星轿车维修手册/sort03/sort0147/down-7176.html尼桑Y61 99-3电子维修手册/sort03/sort0147/down-7177.html尼桑Y61电子维修手册/sort03/sort0147/down-7178.html欧宝电路维修手册/sort03/sort0147/down-7179.html欧蓝德2004维修手册/sort03/sort0147/down-7181.html帕杰罗06英文版维修手册/sort03/sort0147/down-7182.html 奇瑞瑞麒2维修手册/sort03/sort0147/down-7183.html起亚电路维修手册/sort03/sort0147/down-7186.html日产俊逸维修手册/sort03/sort0147/down-7187.html日产尼桑A33电子维修保养手册/sort03/sort0147/down-7188.html日产尼桑B14电子维修保养手册/sort03/sort0147/down-7189.html日产尼桑D22电子维修保养手册01年/sort03/sort0147/down-7190.html日产尼桑D22电子维修保养手册98年/sort03/sort0147/down-7191.html日产尼桑E25电子维修保养手册/sort03/sort0147/down-7192.html日产尼桑N16电子维修保养手册/sort03/sort0147/down-7193.html日产尼桑T30电子维修保养手册/sort03/sort0147/down-日产尼桑U13电子维修保养手册/sort03/sort0147/down-7195.html日产尼桑W41电子维修保养手册/sort03/sort0147/down-7196.html日产尼桑Y61电子维修保养手册01年/sort03/sort0147/down-7197.html日产尼桑风度A32电子维修保养手册/sort03/sort0147/down-7200.html上汽荣威750维修手册【上】/sort03/sort0147/down-7203.html上汽荣威750维修手册【中】/sort03/sort0147/down-7202.html上汽荣威750维修手册【下】/sort03/sort0147/down-7201.html双龙汽车维修手册/sort03/sort0147/down-7204.html天籁电子维修手册/sort03/sort0147/down-7206.html原厂丰田凯美瑞维修手册/sort03/sort0147/down-7209.html原厂威驰维修手册/sort03/sort0147/down-7217.html丰田锐志2005原厂维修手册/sort03/sort0147/down-9082.html广州本田honda维修手册/sort03/sort0147/down-10866.html 途安维修手册(无电路图）/sort03/sort0147/down-13851.html 宝马315-323i 维修手册/sort03/sort0147/down-14412.html 本田CRV维修手册/sort03/sort0147/down-14413.html长安之星微型汽车维修手册(上) /sort03/sort0147/down-14421.html长安之星微型汽车维修手册(下) /sort03/sort0147/down-14422.html依维柯汽车与长安微型汽车维修手册/sort03/sort0147/down-北京现代酷派汽车电路维修手册(上) /sort03/sort0147/down-14440.html北京现代酷派汽车电路维修手册(中) /sort03/sort0147/down-14439.html北京现代酷派汽车电路维修手册(下) /sort03/sort0147/down-14438.html别克世纪、皇朝汽车维修手册（电控发动机）上/sort03/sort0147/down-14442.html 别克世纪、皇朝汽车维修手册（电控发动机）下/sort03/sort0147/down-14441.html 长安1.6L发动机维修手册/sort03/sort0147/down-14443.html长安MF514A01手动变速器维修手册/sort03/sort0147/down-14444.html道奇捷龙汽车维修手册/sort03/sort0147/down-14451.html菲亚特汽车维修手册/sort03/sort0147/down-14453.html广州本田飞度汽车车身电器维修手册/sort03/sort0147/down-14454.html广州本田飞度汽车空调暖风系统维修手册/sort03/sort0147/down-14455.html捷达前卫轿车维修手册/sort03/sort0147/down-14457.html奇瑞瑞虎汽车电路维修手册/sort03/sort0147/down-14458.html通用鲁米娜汽车维修手册/sort03/sort0147/down-14465.html 本田雅阁轿车悬挂系统检修手册/sort03/sort0147/down-14518.html比亚迪F6维修手册（部分）/sort03/sort0147/down-14519.html丰田霸道原厂维修手册/sort03/sort0147/down-14521.html丰田佳美2.2／3.0轿车维修手册(上) /sort03/sort0147/down-14522.html丰田佳美2.2／3.0轿车维修手册(下) /sort03/sort0147/down-14523.html2003 赛欧SGM7160 SL SC 系列中文维修手册/sort03/sort0147/down-14672.html 江铃汽车T系列汽油欧Ⅲ维修手册/sort03/sort0147/down-14684.html江淮瑞风英文维修手册/sort03/sort0147/down-14711.html上海POLO轿车维修手册/sort03/sort0147/down-14714.html 上海大众GOL(2003)维修手册(下) /sort03/sort0147/down-14781.html上海大众GOL(2003)维修手册(上) /sort03/sort0147/down-14782.html比亚迪F0电喷系统维修手册/sort03/sort0147/down-14947.html雨燕维修手册/sort03/sort0147/down-14989.html吉利金刚原厂维修手册/sort03/sort0147/down-15103.html雪弗兰科西佳轿车维修手册（上）/sort03/sort0147/down-15134.html雪弗兰科西佳轿车维修手册（下）/sort03/sort0147/down-15133.html日产汽车D22 98-10维修手册(增补2) /sort03/sort0147/down-15240.html日产汽车D22 98-10维修手册/sort03/sort0147/down-15241.html日产汽车E25维修手册/sort03/sort0147/down-15242.html日产汽车N16维修手册/sort03/sort0147/down-15243.html .14/List_feizhuliu/3387407_70_1.html二月六号后更新维修手册请进入网站下载更多汽车维修手册、维修电路图到精通维修下载站下载此文档是由网络收集并进行重新排版整理.word可编辑版本！。

本文部分内容来自网络整理，本司不为其真实性负责，如有异议或侵权请及时联系，本司将立即删除！== 本文为word格式，下载后可方便编辑和修改！ ==1.5雨燕说明书篇一：关于雨燕保养费用总结关于雨燕保养费用总结对于YY保养费用都是我们最关心问题，身边很多哥们在保养的时候，都被4s收了超额费用，或者增加很多不必要的保养项目，感觉很有必要对雨燕保养费用做个总结。

以下内容是我从各地儿收集的信息来给大家看看参考参考总的来说，雨燕，特别是 1.3雨燕的保养费用还是比较便宜的，特别是和大众、通用、丰田、日产等合资品牌比。

但4S有些保养件价格偏贵，而且有些项目并非必须或者很早去做。

以下分别列出一些可以节约开支的地方。

(本文分析以1.3雨燕为基础)一．保养周期。

所有4s都说雨燕保养周期是5000公里。

但实际上保养手册中规定的强制周期是10000公里或者6个月。

保修期内达到这个强制周期必须到指定的4s去保养，否则视同弃保。

这意味着：1.对于自带高级机油如美孚1号或者灰壳的车友，完全可以适当延长保养周期。

2. 对于用普通矿物机油的车友，可以选择5000公里在其他地方换机油机滤，1万公里再到4s做保养。

当然，这是理论上的分析，具体是否可以实行，还需要看各地4s的态度和车友沟通的结果。

毕竟中国的国情所限，很多正当的规定并非能够顺利执行。

节约总结：至少可以节约50元。

二．保养配件。

除了机滤本身比较便宜外，4s保养配件价格和网上价格差距通常在2到3倍。

例如，1. 空气滤芯，4s价格在70元，网上价格通常在20到30块之间，差价2-3倍。

雨燕的空气滤芯非常好换，不用工具，只需要打开4个卡子即可换。

建议自买自换。

1. 汽油滤芯，原厂为索菲玛品牌，此品牌淘宝价格通常在35元左右，4s价格在110元左右，差价在3倍多。

2. 机油滤芯，原厂15元左右，网上有10元左右的滤芯，差价不大，可以继续用原厂滤芯。

但对于延长换油周期的朋友，可以考虑用Denso等好品牌的滤芯。

Suzuki Swift MK3 – replacementguideVIDEO TUTORIAL415)Important!REPLACEMENT: BRAKE PADS – SUZUKI SWIFT MK3.TOOLS YOU MIGHT NEED:Wire brushWD-40 sprayBrake cleanerAnti-squeal pasteCopper greaseCombination spanner #15Drive socket # 13Wheel impact socket #21Ratchet wrench Torque wrench Brake caliper wind back tool Crow bar Wheel chockCARRY OUT REPLACEMENT IN THE FOLLOWING ORDER:1Open the bonnet. Unscrew the brake fluid reservoir cap.Perform the replacement of brake pads in complete set for eachaxis. This provides effective braking.The replacement procedure is identical for all brake pads on thesame axle.Please note: all work on the car – Suzuki Swift MK3 – should bedone with the engine switched off.2Secure the wheels with chocks.3Loosen the wheel mounting bolts. Use wheel impact socket #21.4Raise the front of the car and secure on supports.5Unscrew the wheel bolts.AUTODOC recommends:6Remove the wheel.Important! Hold the wheel while unscrewing the fastening bolts.Suzuki Swift MK37Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.8Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.9Spread the brake pads. Use a crowbar.10Remove the brake caliper.Tie the caliper to the suspension or to the body with a wire withoutdisconnecting from the brake hose to prevent depressurization ofthe brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has beenremoved. As a result, the piston can fall out from the brake cylinder,and brake fluid leakage and depressurization of the system mayoccur.Check the brake caliper bracket, brake caliper guide pins and boots.Clean them. Replace, if necessary.11Remove the brake pads.experts recommend:12Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.Measure the brake disc thickness. Upon reaching the wear limit thepart must be replaced.13Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.recommend:Replacement: brake pads – Suzuki Swift MK3. After applying thespray, wait a few minutes.Make sure the disc surface is clean before installing the pads.14Install new brake pads.recommends:Make sure the pads are installed with linings facing the disc.15Treat the brake caliper piston. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – Suzuki Swift MK3. After applying thespray, wait a few minutes.16Press in the brake caliper piston. Use brake caliper wind back tool.17.1Install the brake caliper and fix it.17.2Use a combination spanner #15. Use a drive socket #13. Use a torque wrench. Tighten it to 35 Nm torque.18Treat the surface where the brake disc contacts the wheel rim. Use copper grease.19Clean the brake disk surface. Use a brake cleaner.recommend:20Install the wheel.After applying the spray, wait a few minutes.21Screw in the wheel bolts. Use wheel impact socket #21.22Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 125 nm torque.Warning! To avoid injury, hold the wheel while screwing in thefastening bolts on the car. Suzuki Swift MK323Remove the jacks and chocks.Check the brake fluid level in the expansion tank and refill ifnecessary.24Tighten the brake fluid reservoir cap. Close the hood.experts recommend:Without starting the engine, press the brake pedal several timesuntil you feel significant resistance.Slow down smoothly for first 150-200 km after the brake padsreplacement. Avoid unneccessary and sharp braking to a stop.DID YOU FIND THESE INSTRUCTIONSHELPFUL?YES NOAUTODOC — TOP QUALITY AND AFFORDABLE CARPARTS ONLINESHOPPINGA GREAT SELECTION OF SPARE PARTS FOR YOUR CARBRAKE PADS: A WIDE SELECTIONBRAKE PADS FOR SUZUKI: BUY NOWBRAKE PADS FOR SUZUKI SWIFT MK3: THE BEST DEALS & OFFERS The document contains only general recommendations that may be useful for you when you perform repair or replacement work. AutoDoc shall not be liable for any loss, injury, damage of property occurring in the repair or replacement process due to incorrect use or misinterpretation of the provided information.AutoDoc shall not be liable for any possible mistakes and uncertainties in this guide. The information provided is for information purposes only and cannot replace advice from specialists.AutoDoc shall not be liable for incorrect or hazardous usage of equipment, tools and car parts. AutoDoc strongly recommends to be careful and observe the safety rules when performing repair or replacement works. Remember: usage of low quality auto parts does not guarantee you the appropriate level of road safety.© Copyright 2018 – All the contents of this website, in particular texts, photographs and graphics, are protected by copyright. All rights,including reproduction, publication, editing and translation rights, are reserved by Autodoc GmbH. 21–21Disclaimer:。

Maintenance of Pleasureboat Diesel EngineGM Series1.Safety Precaution for Inspection1)Battery FluidBattery fluid is diluted sulfuric acid. It can blind you if it gets in your eyes, or burn your skin. Keep the fluid away from your body. Wash it off immediately with a large quantity of fresh water if you get any on you.2)Fire due to Electric Short-CircuitsAlways turn off the battery switch or detach the earth cable(-) before inspecting the electrical system.Failure to do so could cause short-circuiting and fires.3)Precautions for Moving PartsStop the engine before you service it. If you must inspect while the engine is operating, never touch moving parts. Keep your body and clothing well clear of all moving parts as this could result in injury.4)Precautions for Removing Hot Oil and Water to Prevent BurnsIf extracting oil from the engine while it is still hot, do not let the oil splash on you.Wait until the temperature has dropped before removing cooling water from the engine to avoid getting scalded.5)Burns from Contact with Hot Engine PartsThe whole engine is hot during operation and immediately after stopping.The turbocharger, exhaust manifold, exhaust pipe, and engine are very hot.Never touch these parts with your body or clothing.6)Burns from Scaldingl Never remove the filler cap of the fresh water cooler while the engine is still hot. Stream and hot water will spurt out and seriously burn you. Wait until the water temperature has dropped, thenwrap a cloth around the cap and loosen it slowly.l After inspection, refasten the filler cap firmly. If the cap is not secure, steam or scalding watermay be emitted during operation causing burns.2.Engine SpecificationsType Vertical water-cooled 4-cycle diesel engineEngine Model 1GM10 2GM20(F) 3GM30(F) Number of cylinders 1 2 3Cont. rating output 5.9kW(8PS)/3400min-111.8kW(16PS)/3400min-117.7kW(24PS)/3400min-1Max. output 6.6kW(9PS)/3600min-113.2kW(18PS)/3600min-119.9kW(27PS)/3600min-1Lube oil capacity EngineoilL 1.3L 2.0L 2.7L Clutch oil L 0.25L 0.25L 0.3L3.Fuel oil, lube oil and cooling water 3.1 fuel oil3.2 Lube oil3.3 Cooling water (Fresh water cooling type)1)1) Selection of fuel oilUse the following diesel fuels or equivalents. Select fuels of a higher quality for best engine performance.[Diesel fuel standard for various countries]l ISO 8217 DMAl ASTM D975 Grade No.1-D or No.2-Dl JIS K2204 Grade No.2, No.3 or special-No.3 lBS 2869 Part-1 class-A1 or A2At low temperatures, fuel oil becomes difficult to ignite and will not flow easily, making startingdifficult. Select fuel oil of a cetane of 45 or greater to insure ignitability, and use the outside temperature as a guide for selecting the proper grade to insure fluidity. 2)Handling of Fuel OillKeep the fuel oil in a clean container. Store the container in a place away from rain and dirt as water and dust mixed in with the fuel cause engine failure.lKeep the fuel container stationery for several hours to allow any dirt or water to settle to the bottom. Use a pump to extract the clear, filtered fuel from the top of the container for use.1)Selection of Engine oil Use the following lube oil API Classification•• CD SAE Viscosity •• 15W402)2) Selection of Marine gear lube oil API Classification •• CD SAE Viscosity •• #30 3)Handling the Lube OillWhen handling and storing lube oil, be careful not to allow dust and water to enter the lube oil. Clean around the filler port before refilling.lDo not mix. lube oils of different types or brands.Mixing may reduce the lubricating performance. Different oils are used for the engine and the marine gear.Be careful to use the correct oil for each one and store in separate clearly labeled containers1)Always use soft water (tap water) for the fresh water. Never use dirty water or hard water. Impurities in the cooling water cause scale and rust to build up in the cooling system reduction cooling efficiency and causing the engine to overheat.2)During the cold season, add antifreeze to the cooling water to prevent freezing. Failure to add antifreeze will result in damage to various parts in the cooling water system.3)Refer to the instruction accompanying the antifreeze for the proper mixing ratio. Select the ratio for the lowest temperature of the cold season. If the mixture is too thick, the cooling efficiency will be reduced.4)Do not mix different brands of antifreeze or anti-rust. Mixing reduces cooling efficiency and leads to parts damage.5)When the amount of cooling water is too low, refill with fresh water only.4.Maintenance and Inspection4.1 Fuel Oil System4.1.14.1.1 Checking and Supplying Fuel OilCheck the fuel level inside the fuel tank and supply with the recommended fuel if necessary.Inspection •• daily (before starting)4.1.2Draining the fuel tank1.Put a pan under the drain to catch the fuel.2.Loosen the drain cock at the bottom of the fuel tank, and drain off any water and dirt collectedinside.3.Once the water and dirt have been drained off and the fuel coming out is clear, close the drainplug.Inspection •• every 50hrs.4.1.3Replacing the fuel filter1.Close the fuel cook.2.Turn the element casing fixing screw to the left withthe filter wrench and remove.3.Clean the filter casing.4.Turn the element casing fixing screw to the right, usethe filter wrench to tighten.5.Be sure be bleed air out of the fuel system.4.2 Lube Oil System4.2.1Checking and Supplying Engine oil1.Check the engine oil level with the oil dipstick.2.If the oil level is low, supply with the recommended lube oil using the filler port.Supply oil up to the upper mark on the oil dipstick.Inspection •• daily (before start-up)4.2.2Check and supply of Marine gear oil1.Check the marine gear oil level with the oil dipstick.2.Supply with the recommended oil if necessary.Check the oil level with the dipstick while to the uppermark.Inspection •• daily (before starting)4.2.3 Replacing the Engine Lube Oil and Lube Oil Filters1.Drain off the lube oil.It is easier and more effective to drain the engine lube oil while the engine is still warm afteroperation.1) After removing the oil dipstick, attach the hose of the oil drain pump to the dipstick guidehole.2) Drain off the oil with the drain pump.2.Replace the lube oil filter1) Turn the lube oil filter to the left with the filter wrench and remove.2) Clean the filter installation face.3) Apply engine oil to the installation face and put on the new filter, turning it to the right byhand. Next, tighten an additional 3/4 of a turn with the filter wrench.3.Fill with new lube oil.1) Fill with the specified amount of engine oil.¡Remove the oil inlet cap on the top of the bonnet and fill with oil.¡Remove the oil dipstick and check the level of the oil with the gauge on the stick. Oilshould be filled to the upper mark on the dipstick gauge¡Replace the dipstick and tighten the oil inlet cap firmly by hand.2•Run the engine for approximately 5 minutes and check to see if there is any oilleakage3) Approximately 10 minutes after stopping, check the oil level again with the oildipstick and more oil if necessary.Replace first ••• after initial 50 hoursSecond time and thereafter •• every 250 hours( 1 year)4.2.4 Replacing the Marine Gear Lube OilReplace the lube oil in the marine gear by using the procedure described above.Replacefirst •• after initial 50 hourssecond time •• every 250 hoursthereafter •• every 1000 hours4.3 Cooling Water System4.3.1Check and supply of cooling water1.Check the cooling water level in the sub-tank.If the water level is close to the lower limit, remove the sub tank cap and fill with fresh waterto the upper limit.2.When the water level in the sub-tank is low, remove the filler cap for the fresh water tank andcheck the amount of cooling water in the fresh water tank. Fill with fresh water to overflowingif the level is low.¡Check the fresh water level before operation while the engine is cold.Checking the water level while the engine is hot is dangerous, and the cooling waterreading will be misleading due to thermal expansion.¡Check and supply cooling water daily at the sub-tank.Do not remove the fresh water cooler f1iller cap regularly.¡The amount of water in the sub tank will increase during operation. This is normal.When the engine is stopped, the temperature of the cooling water will drop causing theextra water in the sub tank to return to the fresh water tank.Inspection •• daily (before starting)4.3.2Checking discharged from the seawater outlet pipeCheck that sufficient cooling water is discharged from the seawater outlet pipe. Operation with too little seawater discharge will burn the impeller of the seawater pump. If seawater discharge is too small, stop the engine immediately, identify the cause and repair.¡Is the Kingston cock open¡Is the inlet of the Kingston cock clogged¡Is the sea water suction hose broken, or does the hose suck in air due to a loose joint4.3.3Inspecting Inner Parts of the Seawater PumpThe inside parts of the seawater pump will deteriorate with use, and discharge performance falls. At the specified interval or when the volume of seawater discharged is reduced, inspect the seawater pump in accordance with the following procedures.1.Loosen the side cover set bolt and remove the side cover.2.Illuminate the inside of the seawater pump with a flashlight and inspect. If any of the followingproblems is found, disassembly and maintenance are necessary.¡Impeller blades are cracked or nicked. Edges or surfaces of the blades are marred orworm. The impeller must be replaced periodically every 2000 hrs.¡Wear plate is damaged.3.If no damage is found when inspecting the inside of the pump, replace the side cover. Fit theO-ring to the groove of the joint face before replacing the side cover.If a large amount of water leaks continuously from the seawater pump during operation,disassembly and maintenance ( replacement of the mechanical seal ) are necessary.When disassembly and maintenance of the seawater pump are necessary, consult your Yanmardealer or distributor.Inspection •• every 1000 hours.Replace •• every 2000 hours.4.3.4Inspection and Replace Anti-corrosive zinc (seawater cooling line)1.Close the Kingston cock.2.Drain the cooling seawater.3.Remove the plug labeled ZINC and indicated in the diagram.4.Check the zinc on the inside of the plug to determine the amount of wear to the anti-corrosivezinc.¡Replace the anti-corrosive zinc when it has been reduced to less than 1/2 of its originalsize.¡If there is only a little bit of wear, clean the surface by sanding off any corroded areas.5.Replace plug.6.Open the Kingston cock and check water leakage.Inspection •• every 500 hours.4.4 Inspection of the Electrical Parts4.4.1 Inspection of Batteryl Check the level of fluid in the battery.When the amount of fluid nears the lower limit, fill with battery fluid (available in the market)to the upper limit. If operation continues with insufficient battery fluid, the battery life isshortened, and the battery may overheat and explode.l Battery fluid tends to evaporate more quickly in the summer, and the fluid level should bechecked earlier than the specified times.l If the engine turns over at a slower than usual rate and refuses to start, recharge the battery.l If the engine still will not start after charging, replace the battery.Inspection •• daily (before start-up)4.4.2 Checking the Tension of the V-Belt of the AlternatorWhen there is not enough tension in the V-belt, the belt will slip making it impossible for thealternator to generate power.Additionally, the fresh water pump will not work causing the engine to overheat.Check the tension of the V-belt in the following manner.1.Press the V-belt down with your thumb at the middle of the belt to check the tension.The give in the V-belt should measure about 8 • 10mm at the depression.2.To adjust the V-belt tension, loosen the set bolt and move the alternator.3.Replace the belt if it is damaged.Inspection •• every 500 hoursReplace •• every 2000 hours4.4.3Adjusting the Remote Control HandleThe remote control handles and the engine control levers are connected by an accelerator cable. Over time the cable becomes stretched and the connections loose causing deviation in the position, which makes operation unsafe. Inspect the cable periodically and adjust if necessary.1.Adjusting the Governor Remote Control Handle¡Check to see that the speed lever on the engine side is touching the high speed limitingbolt when the governor handle is put in H ( High Speed ).¡Check to see that the speed lever on the engine side is touching the low speed limitingbolt when the governor handle is put in L ( Low Speed ).¡If the speed lever does not touch the limiting bolt for either the high or low speed, whenyou check them, loosen the setting screws on the fittings for the accelerator cable andadjust the position of the cable.2.Adjusting the Clutch Remote Control Handle for the Marine Gear¡Check to see that the clutch lever on the engine side is in the neutral position when theremote control handle is in NEUTRAL.¡ If the position of the clutch lever is incorrect, loosen the setting screw of the cable.¡Check the clutch lever in▲ FWD ( Forward )▼ REV ( Reverse )making sure it is correctly aligned.¡Make any necessary adjustments using NEWTRAL as the central point.Inspection •• every 250 hours5. Principal specifications5.1 SpecificationsEngine Model 1GM10 2GM20(F) 3GM30(F)Idling speed min-1 850±25High idling speed min-1 3825±25Firing order -1-2-1 1-3-4-2-1 Valve clearanceSuction •• 0.2±0.03 Exhaust•• 0.2±0.03Injection timing (FID) bTDC 15°±1 bTDC 15°±1 bTDC 18°±1Injection pressureMpa 19.6±0.49 (200±5kg/cm2) Lubricant pressure Mpa0.39±0.05 (4.0±0.5kg/cm2)6. Trouble and troubleshootingIf you should encounter some difficulty during operation, refer to the following table for countermeasures. Trouble Probable Cause Measure Problem occurs during operation. NOTICEWhen the alarm equipment indicates a problem, immediately put the clutch in neutral and run the engine at low speed.Check to see which alarm indicator is lit, then stop the engine and inspect.When you cannot determine the source of the problem, return to port at low speed and ask your Yanmar dealer for repair.Alarm buzzer sounds and alarm come on. Faulty battery Check battery fluid.V-belt is loose or damagedAdjust V-belt tension or replacebelt.Charge Lamp(Alarm buzzer does not sound)Alternator is not generatingelectricityAsk for repairs.Insufficient cooling water in fresh water tankCheck and replenish coolingwater.Leakage in fresh water cooling system Ask for repairs for water leakage. Fresh water cooling pump is damaged Ask for repairs. C.W. Temp. Lamp goes on Inside of C.W. system is dirty Ask for repairs. L.O. Press. Alarm Lamp goes on Insufficient engine oil Replenish engine oil.Insufficient discharge of cooling seawaterKingston cock is closed. Kingston cock is clogged. Suction hose is damaged or joints loose.Exhaust Alarm Lamp goes on Damaged cooling seawater pump Check seawater pump impeller. Faulty Alarm DeviceNOTICEDo not operate the engine if alarm devices are not working properly.Serious accidents may result if difficulties are not spotted due to faulty alarm lamps.Before starting when switch is turned from OFF → ON, alarm devices do not work.Alarm buzzer does not sound. Circuit broken or buzzerdamaged.Ask for repairs.Some alarm lamps do not light up. Circuit broken or lamp burnt out. Ask for repairs.After starting when switch returns from START → ON, alarm devices do not work.Alarm buzzer does not cut off. Short circuit Ask for repairs.Some alarm lamps do not go out. Damaged sensor or switch Ask for repairs.Starting FailuresNo fuel Replenish fuel: bleed.Air in fuel line Bleed.Bad fuel Replace with recommended fuel. Clogged fuel filter Replace fuel filter.Poor fuel injection Ask for repairs.Starter does not turn. Pressure leakage fromintake/exhaust valvesAsk for repairs.Insufficient battery charge Check battery fluid, recharge.Faulty cable connection at terminal Remote rust from terminal; retightenFaulty starter switch Ask for repairs.Starter does not turn or turns toosolely(can be turned by hand)Faulty starter Ask for repairs.Cannot be turned manually Inner parts seized or damaged Ask for repairs.Poor exhaust colorOverload Reduce load.Insufficient fuel Replace with recommended fuel. Faulty spraying of F.O. injection Ask for repairs.Black smoke emitted. Excessive intake/exhaust valvetop clearanceAsk for repairs.Insufficient fuel Replace with recommended fuel. Faulty spraying of F.O. injection Ask for repairs.Fuel injection timing off Ask for repairs.White smoke emitted. Lube oil burns/excessiveconsumptionAsk for repairs.。

本文部分内容来自网络整理，本司不为其真实性负责，如有异议或侵权请及时联系，本司将立即删除！== 本文为word格式，下载后可方便编辑和修改！ ==铃木雨燕,说明书,pdf篇一：家用实用小车铃木雨燕解析铃木雨燕是一款定位于A0级的紧凑型小车，价位低、时尚的设计及较低的油耗，让它变成了新时代家用及操控两不误的实用车型。

谁说外形不重要！一款想要给消费者留下深刻印象的车，一定要有自己的特色及设计风格。

力求消费者从看到它的那一刻开始，它的形象就会深深地印在脑海中。

雨燕在这点上并不例外，其经典的外形设计完全能够赢得大多数消费者的青睐，而与时俱进的细节特征则保证了它能够始终站在时尚的前沿。

相对来说，合资及自主品牌旗下的小型车利润都不算高，但是小型车市场中的竞争却愈演愈烈，特别是合资自主品牌车型的出现，让一些合资车企都感受到了不小的压力。

作为长安铃木的主力车型，雨燕肩负着拉高品牌销量的重任，因此适时的升级改款必不可少。

相比于老款车型，雨燕在保留经典外形设计的同时，对一些细节之处进行了重新设计，新车型采用了大尺寸蜂窝形进气格栅和带有银边锋锐造型的雾灯，全新多辐灵动轮毂充满动感气息，后保险杠以及后雾灯造型同样有所改变，让原本就时尚可爱的雨燕变得更新颖，更富有朝气。

长安铃木雨燕的轴距为2390mm，因此车内空间对于雨燕来说是个不小的考验。

在试驾过程中，我首先坐进雨燕的后排试乘，看着并不宽敞的腿部空间却没有让我的膝盖顶到前排座椅后背，而头部空间也算是够用，不过余量都不算大，想必如果后排坐上3个身材娇小的女士，乘坐感还是比较舒服的，但如果是像笔者这样膀大腰圆的壮汉，那就有些难为雨燕了。

当我换乘到驾驶员座椅时，立刻觉得车内空间宽敞了不少，不但头部空间完全够用，而且在保证前排乘员腿部空间的前提下，并没有过分“压榨”后排乘员那原本就不富裕的空间。

雨燕使用的是麦弗逊式独立前悬架和纵臂扭力梁式半独立后悬架，虽然后悬并非独立悬架，不过千万不要低估雨燕的操控表现，沉稳的转向盘配合铃木工程师精心调校的悬架，依然让驾驶者在高速过弯或者变线时镇定自若。

雨燕1.3说明书篇一：雨燕保养使用手册20XX雨燕车主保养使用手册时尚外形的小车可以说是日系车中的擅长领域，Swift 雨燕便是于20XX年巴黎车展中正式亮相的小型车款。

自04年11月日本上市开始后，去年陆续在中国、匈牙利、印度等地上市，成为不折不扣的铃木世界战略小车。

良好的经济性受到了不少车友的追捧。

但也有部分车友对雨燕引擎、动力方面的表现持否定的观点。

在此收集整理出众多雨燕车主在实际使用感受中对雨燕的优缺点的评价，能客观的反映出雨燕的优势和不足，给所有喜爱雨燕的车友一个参考。

雨燕保养以及使用细节一、走合保养期新车里程在最初的0－100公里时，发动机等运动件表面还较粗糙，其内摩擦阻力大，如不控制车速、负荷、温度，机件就会发生急剧的磨损。

因此，在最初的1000－20XX 公里磨合期内，必须严格按规定行驶。

磨合良好的汽车，其使用寿命、可靠性及经济性将大大提高。

磨合保养期内基本规范要求：1、不能以最大油门过度行驶（建议车速60－80公里／小时）；2、各档发动机转速均不能超过最高转速的3／4；3、汽车最好不要满载；4、经常使用不同档位，以利于各零部件之间的均匀磨合；5、磨合后期可将车速逐渐提高到最高允许速度（各档位车速范围见使用手册）；6、出现任何异常现象，立即向专门人员请教。

注意：磨合后期（1500-2500公里），必须到就近的长安铃木特约维修站进行首次强制保养！以后视情况每6000-10000公里进行一次例行保养。

二、出车前的准备起动前1、检查汽车有无漏水、漏油现象；2、检查机油油位及清洁度；3、检查发动机冷却液、制动液、洗涤液液位（必要时添加）；4、检查皮带张紧度（必要时调整）；5、检查轮胎气压及磨损状况。

起动汽车后1、检查仪表、信号灯、操纵开关是否正常；2、检查发动机及运动附件是否正常，有无异响；3、汽车怠速是否正常。

注意：用户自己在保养车辆时请仔细阅读随车使用手册！三、行驶中注意事项1、冷机起动后，应让发动机预热3－5分钟，最初以中、低速行驶，发动机水温正常后才能高速行驶；2、从经济性及发动机寿命、环保等方面考虑要尽量使用高档行驶，因为此时在同样车速下，发动机的转速最低；3、当车下陡坡或长坡时，要挂上适当的低速档，用发动机辅助制动。

本文部分内容来自网络整理，本司不为其真实性负责，如有异议或侵权请及时联系，本司将立即删除！== 本文为word格式，下载后可方便编辑和修改！ ==雨燕,说明书篇一：雨燕保养使用手册201X雨燕车主保养使用手册时尚外形的小车可以说是日系车中的擅长领域，Swift雨燕便是于201X年巴黎车展中正式亮相的小型车款。

自04年11月日本上市开始后，去年陆续在中国、匈牙利、印度等地上市，成为不折不扣的铃木世界战略小车。

良好的经济性受到了不少车友的追捧。

但也有部分车友对雨燕引擎、动力方面的表现持否定的观点。

在此收集整理出众多雨燕车主在实际使用感受中对雨燕的优缺点的评价，能客观的反映出雨燕的优势和不足，给所有喜爱雨燕的车友一个参考。

雨燕保养以及使用细节一、走合保养期新车里程在最初的0－100公里时，发动机等运动件表面还较粗糙，其内摩擦阻力大，如不控制车速、负荷、温度，机件就会发生急剧的磨损。

因此，在最初的1000－201X公里磨合期内，必须严格按规定行驶。

磨合良好的汽车，其使用寿命、可靠性及经济性将大大提高。

磨合保养期内基本规范要求：1、不能以最大油门过度行驶（建议车速60－80公里／小时）；2、各档发动机转速均不能超过最高转速的3／4；3、汽车最好不要满载；4、经常使用不同档位，以利于各零部件之间的均匀磨合；5、磨合后期可将车速逐渐提高到最高允许速度（各档位车速范围见使用手册）；6、出现任何异常现象，立即向专门人员请教。

注意：磨合后期（1500-2500公里），必须到就近的长安铃木特约维修站进行首次强制保养！以后视情况每6000-10000公里进行一次例行保养。

二、出车前的准备起动前1、检查汽车有无漏水、漏油现象；2、检查机油油位及清洁度；3、检查发动机冷却液、制动液、洗涤液液位（必要时添加）；4、检查皮带张紧度（必要时调整）；5、检查轮胎气压及磨损状况。

起动汽车后1、检查仪表、信号灯、操纵开关是否正常；2、检查发动机及运动附件是否正常，有无异响；3、汽车怠速是否正常。

IndexAccessoriesInstallation.................................. 109ACCESSORY (Ignition KeyPosition)........................................ 50AddingAutomatic TransmissionFluid........................................ 152Brake Fluid................................. 154Clutch Fluid................................ 155Engine Coolant........................... 148Engine Oil................................... 143Manual Transmission Fluid ..... 153Power Steering Fluid................. 155Windshield Washer Fluid......... 151Additional Safety Information........ 18Door Locks................................... 19Driving with Pets......................... 19Head Restraint Position.............. 18Seat-back Position........................ 18Storing Cargo Safely................... 19Additives, Engine Oil..................... 144AdjustmentsMirrors.......................................... 60Head Restraints (56)Seats.............................................. 55Steering Wheel............................ 44Airbag (SRS).................................... 11Air Cleaner..................................... 156Air Conditioning............................... 72Maintenance............................... 165Usage............................................ 74Air Outlets (Vents).......................... 70Air Pressure, Tires........................ 167Alcohol and Drugs........................... 27Alcohol in Gasoline........................ 102Antifreeze....................................... 147Anti-lock Brakes (ABS)Description................................. 220Indicator Light.................... 35, 122Operation.................................... 122Anti-theft Steering Column Lock .. 50Appearance Care........................... 183Ashtray.............................................. 66Audio System................................... 77Automatic Speed Control................ 46Automatic Transmission.............. 116Capacity, Fluid........................... 218Checking Fluid Level................ 152Shifting........................................ 116Shift Lever Positions.. (117)Shift Lock Release (120)BatteryCharging System Light............... 34Jump Starting............................. 200Maintenance............................... 160Specifications............................. 219Before Driving............................... 101Belts, Seat........................................... 5Beverage Holder.............................. 64Body Repair.................................... 190BrakesAnti-lock System (ABS)............ 122Break-in, New Linings .............. 102Fluid............................................ 153Light, Burned-out...................... 176Parking.......................................... 62System Indicator.......................... 34Wear Indicators......................... 121Brakes, ABSDescription................................. 220Operation.................................... 122System Indicator................. 35, 122CONTINUEDIndexBraking System.............................. 121Break-in, New Car......................... 102Brightness Control, Instruments... 41Brights, Headlights......................... 40Bulb ReplacementBack-up Lights........................... 176Brake Lights............................... 176Ceiling Light............................... 179Front Parking Lights................. 175Front Side Marker Lights......... 175Headlights.................................. 172High-mount Brake Light.......... 178License Plate Lights.................. 178Rear Side Marker Lights.......... 177Specifications............................. 219Turn Signal Lights..................... 174Bulbs, Halogen. (173)Cables, Jump Starting With.......... 200Capacities Chart............................. 218Carbon Monoxide Hazard.............. 28Cargo, Loading............................... 110Cassette PlayerCare (97)Operation................................ 81, 90CAUTION, Explanation of.............. ii CD Player.......................................... 93Certification Label......................... 216Chains............................................. 171Change OilHow to......................................... 145When to....................................... 136Changing a Flat Tire..................... 193Changing Engine Coolant............. 149Charging System Indicator .... 34, 205Check Engine Light........................ 35CheckingAutomatic TransmissionFluid........................................ 152Battery Condition...................... 160Brake Fluid................................. 154Clutch Fluid............................... 155Drive Belts.................................. 166Engine Coolant........................... 147Engine Oil................................... 142Fuses.......................................... 208Manual Transmission Fluid..... 153Power Steering Fluid................. 155Checklist, Before Driving............. 112Child Safety.. (20)Cigarette Lighter............................. 66Cleaner, Air.................................... 156CleaningAluminum Wheels..................... 185Carpeting.................................... 187Exterior....................................... 184Fabric.......................................... 187Interior........................................ 187Leather....................................... 187Seat Belts.................................... 188Vinyl............................................ 187Window...................................... 188CLEAN Light................................... 97Clock, Setting the ............................ 63Clutch Fluid.................................... 155Coin Box........................................... 65CO in the Exhaust......................... 221Cold Weather, Starting in............. 114Compact Spare............................... 192Consumer Information.................. 227Controls, Instruments and.............. 31CoolantAdding........................................ 148Checking..................................... 147Proper Solution.......................... 147Temperature Gauge....................38IndexCorrosion Protection..................... 185Crankcase Emission ControlSystem......................................... 224Cruise Control Operation............... 46Customer Relations Office.. (227)DANGER, Explanation of................. ii Dashboard........................................ 32Daytime Running Lights................. 40Dead Battery, What to Do............ 200Defects, Reporting Safety............... 29Defogger, Rear Window................. 43Defrosting the Windows................. 76DEXRON* II AutomaticTransmission Fluid.................... 152Dimensions..................................... 218Dimming the Headlights................ 40DipstickAutomatic Transmission........... 152Engine Oil................................... 142Directional Signals........................... 41Disabled, Towing Your Car If...... 213Disc Brake Wear Indicators......... 121Disposal of Used Oil. (147)DoorsLocking and Unlocking............... 51Power Door Locks....................... 51DOT Tire Quality Grading........... 222Downshifting, 5-speed ManualTransmission.............................. 115Drive Belts...................................... 166Driving............................................ 111Economy..................................... 108In Bad Weather.......................... 123In Foreign Countries.. (103)Economy. Fuel............................... 108Emergencies on the Road............. 191Battery, Jump Starting.............. 200Changing a Flat Tire.. (193)Charging System Indicator...... 205Check Engine Light.................. 206Checking the Fuses................... 209Low Oil Pressure Indicator...... 204Malfunction Indicator Lamp.... 206Manually Closing Moonroof.... 207Overheated Engine................... 202Emergency Brake. (62)Emergency Flashers....................... 43Emission Controls......................... 224EngineBelts............................................. 166Check Engine Light............ 35, 206Coolant Temperature Gauge..... 38Malfunction IndicatorLamp................................. 35, 206Oil Pressure Indicator......... 34, 204Oil, What Kind to Use (143)Overheating................................ 202Specifications............................. 218Ethanol in Gasoline....................... 103Evaporative Emission Controls.... 224Exhaust Fumes................................ 28Expectant Mothers, Use of SeatBelts by......................................... 10Exterior, Cleaning the. (184)Fabric, Cleaning............................. 187Fan, Interior.. (72)CONTINUEDIndexFeatures, Comfort andConvenience................................. 69Filling the Fuel Tank..................... 104FilterOil................................................ 145First Gear, Shifting........................ 1195-speed Manual Transmission,Checking Fluid Level................ 1535-speed Manual Transmission,Shifting the................................. 115Flashers, Hazard Warning.............. 43Flat Tire, Changing a.................... 193FluidsAutomatic Transmission........... 152Brake.......................................... 154Clutch.......................................... 155Manual Transmission............... 153Power Steering........................... 155Windshield Washer................... 151FM Stereo RadioReception...................................... 80Folding Rear Seat............................ 57Foreign Countries, Driving in...... 103Four-way Flashers........................... 43Front End, Towing byEmergency Wrecker (213)Fuel................................................. 102Fill Door and Cap....................... 104Gauge............................................ 38Octane Requirement................. 102Oxygenated................................ 102Tank, Filling the......................... 104Fuses, Checking the. (208)Gas Mileage, Improving................ 108Gasohol........................................... 102Gasoline.......................................... 102Gauge............................................ 38Octane Requirement................. 102Tank, Filling the......................... 104Gas Station Procedures................. 104GaugesEngine Coolant Temperature .... 38Fuel............................................. 38Gearshift Lever PositionsAutomatic Transmission........... 1175-speed ManualTransmission.......................... 115Glass Cleaning............................... 188Glove Box.. (53)Halogen Headlight Bulbs.............. 173Hazard Warning Flashers............... 43Headlights....................................... 40Daytime Running Lights............. 40High Beam Indicator................... 36High Beams, Turning on............ 40Low Beams, Turning on ............. 40Reminder Chime.......................... 40Replacing Halogen Bulbs ......... 172Turning on.................................... 40Head Restraints............................... 56Heating and Cooling........................ 70High Altitude, Starting at.............. 114High-Low Beam Switch .................. 40Hood, Opening the ........................ 105Horn................................................. 49Hot Coolant, Warning About........ 148Hydraulic Clutch............................ 155Hydroplaning. (123)Identification Number, Vehicle.... 216If Your Car Has to be Towed.......213IndexIgnitionKeys.............................................. 49Switch............................................ 50Timing Control System............. 225Indicator Lights, InstrumentPanel............................................. 33Infant Restraint................................ 22Inflation, Proper Tire .................... 167Inside Mirror.................................... 60Inspection, Tire.............................. 168Instrument Panel............................. 32Instrument Panel Brightness......... 41Interior Cleaning............................ 187Interior Lights.................................. 67Introduction.. (i)Jacking up the Car......................... 195Jack, Tire........................................ 194Jump Starting (200)Keys (49)Label, Certification........................ 216Lane Change, Signaling.................. 41Lap Belt............................................... 6Lap/Shoulder Belts........................... 6Leaking of Exhaust into Car.......... 28Lighter, Cigarette............................ 66LightsBulb Replacement..................... 172Indicator........................................ 33Parking.......................................... 40Turn Signal................................... 41Loading Cargo................................ 110LOCK (Ignition Key Position)....... 50LocksAnti-theft Steering Column........ 50Fuel Fill Door............................. 104Glove Box..................................... 53Power Door.................................. 51Trunk............................................ 52Low Coolant Level......................... 147Lower Gear, Downshifting to a.... 115Low Oil Pressure Indicator.... 34, 204Lubricant Specifications Chart.... 218Luggage (110)Maintenance................................... 131Periodic Items............................ 140Record.................................. 138-139Required Indicator....................... 38Schedule.............................. 134-137Malfunction Indicator Lamp.. 35, 206Manual Transmission.................... 115Manual Transmission Fluid ......... 153Maximum Shift Speeds........ 116, 120Meters, Gauges................................ 37Methanol in Gasoline.................... 103Mirrors, Adjusting........................... 66Moonroof.......................................... 59Closing Manually....................... 207Operation.. (59)Neutral Gear Position.................... 118New Vehicle Break-in ................... 102Normal Shift Speeds...................... 115NOTICE, Explanation of................. ii Numbers, Identification. (216)CONTINUED。