铸造英文词汇自己总结

一、基本术语1.铸造：casting , founding ，foundry2。

砂型铸造：Sand casting process3。

特种铸造：Special casting process4.铸件：casting5.毛坯铸件: Rough casting6。

砂型铸件：Sand casting7.试制铸件: Pilot casting8。

铸态铸件：as—cast casting9。

铸型[型]：mold10.铸造工艺: Casting process，foundry technology11。

铸造用材料：Foundry materials12.铸造工艺材料：Consumable materials13。

铸造设备：Foundry equipment，foundry facilities14。

铸工：Caster，founder, foundry worker15。

铸造工作者：foundryman16.铸造车间：Foundry shop17。

铸造厂：Foundry18。

铸造分厂：Attached foundry, captive foundry, tied foundry19.铸造三废：Foundry affluent20.一批： A batch21。

一炉: A cast，a heat, a melt22。

铸焊: Cast welding，flow welding23.铸锭：ingot二、铸造合金及熔炼、浇注2.1铸造合金基础术语1.铸造合金：Cast alloy2.共晶合金系：Eutectic alloy system3.共晶合金：Eutectic alloy4.亚共晶合金: Hypoeutectic alloy5。

过共晶合金：Hypereutectic alloy6.共晶团：Eutectic cell7.共晶温度: Eutectic temperature8.共晶转变：Eutectic reaction，eutectic transformation 9。

铸造英语专用词汇大全材料科学与工程点击上方「材料科学与工程」快速关注材料类综合、全面、专业的微信平台1.基本术语铸造 foundry, founding, casting铸造工艺 foundry technology铸件 casting砂型铸造 sand casting process特种铸造 special casting process2. 合金性能流动性 fluidity充型能力 mold-filling capacity吸气 gas absorption过冷 undercooling supercooling过冷度 degree of undercooling成核 nucleation自发成核（均质成核） homogeneous nucleation非自发成核（非均质成核）heterogeneous nucleation凝固温度范围 solidification range定向凝固（顺序凝固） directional solidification液态收缩（液体收缩） liquid contraction凝固收缩 solidification contraction固态收缩（固体收缩） solid contraction凝固时间 solidification time自由收缩 free contraction受阻收缩 hindered contraction铸件线收缩率 shrinkage收缩应力 contraction stress热应力 thermal stress相变应力 transformation stress,phase change stress 铸造应力 casting stress残留应力（残余应力） residual stress3. 铸造用材料3.1. 金属原材料金属原材料 metallic raw material生铁 pig iron铁合金 ferro-alloy回炉料 foundry returns中间合金 master alloy3.2. 燃料铸造焦炭 foundry coke冶金焦炭 metallurgical coke固定碳 fixed carbon3.3. 熔剂熔剂 flux除气熔剂（除气剂） degassing flux覆盖熔剂（覆盖剂） covering flux精炼熔剂（精炼剂） refining flux耐火度（耐火性） refractoriness耐火砖 firebrick耐火粘土 fireclay硅砖 silica brick镁砂 grain magnesite3.4. 造型材料造型材料 molding material砂 sand水洗砂 washed-out sand硅砂 silica sand天然砂 natural sand人工砂 artificial sand天然粘土砂 naturally clay-bonded sand 橄榄石砂 olivine sand铬铁矿砂 chromite sand锆砂 zircon sand炭粒砂 carbon sand精硅砂 sharp sand红砂 red sand熟料砂 chamotte sand粘结剂 binder粘土 clay无机粘结剂 inorganic binder有机粘结剂 organic binder高岭土 kaolin膨润土 bentonite钠基膨润土 sodium bentonite钙基膨润土 calcium bentonite活化膨润土 activated bentonite干性油 drying oil硬粘结剂(冷硬粘结剂) no bake binder热固树脂粘结剂 thermosetting resin binder油类粘结剂 oil based binder水玻璃粘结剂 water glass binder, sodium silicate binder 纸浆废液 lignin liquor合脂粘结剂 synthetic fat binder水玻璃模数 sodium silicate modulus3.5. 辅助材料附加物 additives发热剂 exothermic mixture分型剂（脱模剂） parting agent,stripping agent固化剂（硬化剂）hardener悬浮剂suspending agent涂料 coating型砂制备（砂处理） sand preparation混砂 sand mulling, sand mixing型砂（造型混合料） molding sand芯砂（造芯混合料） core sand合成砂 synthetic sand自硬砂 self-hardening sand水玻璃砂 sodium silicate-bonded sand覆膜砂 precoated sand烂砂泥（麻泥） loam调匀砂 temper sand面砂 facing sand背砂（填充砂） backing sand单一砂 unit sand含泥量 clay content含水量 moisture content旧砂 floor sand枯砂（焦砂） burnt sand废砂 waste sand热砂 hot sand松砂 aeration , sand-cutting筛分（筛析） screen analysis旧砂处理 sand reconditioning旧砂再生 sand reclamation沉降分选 elutriation, decantation型砂性能及试验型砂试验 sand testing透气性 permeability流动性 flowability型砂强度 sand strength湿强度 green strength干强度 dry strength耐用性（复用性） durability砂型（芯）硬度 mold hardness热变形 hot deformation残留强度 retained strength热强度 hot strength韧性 toughness发气率（发气速度） gas evolution rate 发气性（发气量） gas evolution吸湿性 moisture absorption落砂性 knock-out capability潰散性 collapsibility胶质价 colloid index破碎指数 shatter index热气流烘砂装置 hot pneumatic tube drier混砂机 sand muller, sand mixer松砂机 aerator, sand cutter冷却提升机 cooling elevator, coolevator筛砂机 riddle磁力滚筒 magnetic separator旧砂再生设备 sand reclamation气力输送装置 pneumatic tube conveyor4. 铸造合金4.1. 铸铁铸铁 cast iron铸铁石墨形态 morphology of graphite in cast iron灰铸铁（灰口铸铁） gray cast iron白口铸铁 white cast iron麻口铸铁 mottled cast iron共晶度 degree of saturation碳当量 carbon equivalent初生石墨 primary graphite孕育铸铁 inoculated cast iron球墨铸铁 spheroidal graphite cast iron, nodular graphiteiron, ductile iron球状石墨 spheroidal graphite, nodular graphite可锻铸铁 malleable cast iron黑心可锻铸铁 black heart malleable cast iron珠光体可锻铸铁 pearlitic malleable cast iron铁素体可锻铸铁 ferritic malleable cast iron白心可锻铸铁 white heart malleable cast iron团絮石墨 tempered graphite冷硬铸铁（激冷铸铁） chilled iron耐磨铸铁 wear resisting cast iron耐热铸铁 heat resisting cast iron耐酸铸铁 acid resisting cast iron高硅铸铁 high silicon cast iron蠕墨铸铁 vermicular cast iron,compacted graphite cast iron 蠕虫状石墨 vermicular graphite合金铸铁 alloy cast iron4.2. 铸钢铸钢 cast steel炭素铸钢 carbon cast iron低合金铸钢 low alloy cast steel高锰钢 high manganese steel铁素体钢 ferritic steel铸造非铁合金青铜 bronze铅青铜 lead bronze铝青铜 aluminum bronze黄铜 brass铝铜合金 aluminum-copper alloy铝镁合金 aluminum-magnesium alloy铝硅合金 aluminum-silicon alloy镁合金 magnesium alloy轴承合金（减摩合金） bearing metal, antifrictional metal巴氏合金 babbitt alloy钛合金 titanium alloy5. 熔炼工艺及设备5.1. 熔炼基本术语熔化（熔炼） melting重熔 remelting炉料 charge熔化率 melting rate炉料计算 charge calculation双联熔炼 duplexing元素烧损（元素烧损率）melting losses of various chemical elements熔炼损耗（烧损） total melting loss还原气氛 reducing atmosphere氧化气氛 oxidizing atmosphere惰性气体 inert gas碱度（碱性指数） index of basicity碱性渣 basic slag酸性渣 acid slag精炼 refining遗传性 heredity风口比 tuyere ratio有效高度 effective height送风强度 blast intensity预热送风 hot blast底焦 coke bed层焦 coke split隔焦（结力焦） buffer coke charge炉衬 furnace lining碱性炉衬 basic lining酸性炉衬 acid lining棚料 bridging熔池 bath吸碳 carbon pick-up铁焦比（焦比） iron-coke ratio出渣 deslagging打炉 cupola drop5.2. 铸钢氧化熔炼法 oxidizing melting不氧化熔炼法 dead melting真空熔炼 vacuum refining电渣熔炼 electro-slag melting熔渣 slag沉渣 sludge浮渣 dross, cinder氧化期（沸腾期） oxidizing stage,boil 还原期 deoxidizing stage,blocking stage 还原渣 reducing slag氧化渣 oxidizing slag白渣 white slag脱氧 deoxidation扒渣 slagging- off脱碳 decarburization脱硫 desulphurization脱磷 dephosphorization增碳 recarburizing脱氧剂 deoxidizer挥发损耗 volatilizing losses静置 stewing, holding吹氮 nitrogen flushing5.3. 熔炼设备冲天炉 cupola水冷冲天炉 water-cooled cupola热风冲天炉 hot-blast cupola湿法除尘器 wet cap炉缸 cupola well前炉 forehearth冲天炉加料机 cupola charging machine爬式加料机 skip hoist电磁配铁称 electro-magnetic weighing balancer电磁盘 electromagnetic chuck电弧炉（直接电弧炉） arc furnace,direct arc furnace 感应电炉 electric induction furnace电渣炉 electroslag furnace电磁搅拌electromagnetic agitation浇包 ladle摇包 shaking ladle底注包 bottom pouring ladle保温炉holding furnace坩埚炉crucible furnace孕育 inoculation多孔塞法 porous plug process变质 modification墨化剂 graphitizer过热 superheating石墨球化处理 nodularizing treatment of graphite碳当量仪eutectometer三角试块 wedge test-piece真空除气vacuum degassing5.4. 浇注浇注 pouring保护气氛浇注 pouring under controlled atmosphere 浇注速度 pouring rate浇注温度 pouring temperature浇注时间 pouring time浇注位置 pouring position型内孕育 inmold inoculation压铁 weight捣冒口 churning, pumping点冒口（补注） teeming浸入式高温计 immersion pyremeter补炉 patching炉龄（炉衬寿命） campaign文章来源：粉末冶金圈今日编辑：麦片点击阅读原文，加入交流群。

一、基本术语1.铸造：casting , founding , foundry2.砂型铸造：Sand casting process3.特种铸造：Special casting process4.铸件：casting5.毛坯铸件：Rough casting6.砂型铸件：Sand casting7.试制铸件：Pilot casting8.铸态铸件：as-cast casting9.铸型[型]：mold10.铸造工艺：Casting process, foundry technology11.铸造用材料：Foundry materials12.铸造工艺材料：Consumable materials13.铸造设备：Foundry equipment, foundry facilities14.铸工：Caster, founder, foundry worker15.铸造工作者：foundryman16.铸造车间：Foundry shop17.铸造厂：Foundry18.铸造分厂：Attached foundry, captive foundry, tied foundry19.铸造三废：Foundry affluent20.一批： A batch21.一炉： A cast, a heat, a melt22.铸焊：Cast welding, flow welding23.铸锭：ingot二、铸造合金及熔炼、浇注2.1铸造合金基础术语1.铸造合金：Cast alloy2.共晶合金系：Eutectic alloy system3.共晶合金：Eutectic alloy4.亚共晶合金：Hypoeutectic alloy5.过共晶合金：Hypereutectic alloy6.共晶团：Eutectic cell7.共晶温度：Eutectic temperature8.共晶转变：Eutectic reaction, eutectic transformation9.共晶组织：Eutectic structure10.铸造复合材料：Cast composite11.定向共晶复合材料：Directional eutectic composite12.非晶态合金：noncrystalline alloy13.合金元素：Alloying element14.杂质合金：Tramp element15.合金遗传性：Alloy heredity16.铸态组织：As-cast structure17.铁碳相图：iron-carbon phase diagram18.碳化物：Carbide19.渗碳物：cementite20.碳化物形成元素：Carbide forming element21.单铸试块：Separated test bar of casting22.附铸试块：test lug23.本体试样：Test specimen from casting itself24.过热：Superheating25.过冷：supercooling, undercooling26.成分过冷：constitutional supercooling27.过冷度：degree of undercooling28.加热相变点[Ac相变点]：Ac transformation temperature29.冷却相变点[Ar相变点]：Ar transformation temperature30.结晶：Crystallization31.形核[成核]：Nucleation32.均质形核[自发形核]：Homogeneous nucleation33.非均质形核[非自发形核]：Heterogeneous nucleation34.动力形核：Dynamic nucleation35.大冲击形核：Big bang nucleation36.形核剂：nucleant37.形核率：Nucleation rate38.成长：Growth39.内生生长：Endogenous growth40.外生生长：Exogenous growth41.共生生长：Coupled growth42.小平面型生长：Faceted growth43.非小平面生长：nonfaceted growth44.晶体生长界面[界面]：Growth interface of crystal, interface45.吸气（金属）：Gas absorption (metal)2.2铸钢1.铸钢：Cast steel2.铸造碳钢：Carbon cast steel3.铸造合金钢：Alloy cast steel4.低合金铸钢：Low alloy cast steel5.微量合金化铸钢：Micro-alloying cast steel, trace alloying cast steel6.铁素体铸钢：ferritic cast steel7.奥氏体铸钢：Austenitic cast steel8.不锈钢：Stainless steel9.无磁性铸钢：Non-magnetic cast steel10.高锰钢：Austenitic manganese steel, high manganese steel11.高强度铸钢：High strength cast steel12.超高强度铸钢：Ultra high strength cast steel13.耐磨铸钢：Wear resisting cast steel14.耐热铸钢：Heat resisting cast steel15.耐蚀铸钢：Corrosion resisting cast steel16.石墨钢：Graphitic steel17.铸钢锚链钢：Cast steel for chain cables2.3铸铁1.铸铁：Cast iron2.合成铸铁：Synthetic cast iron3.共晶铸铁：Eutectic cast iron4.亚共晶铸铁：Hypoeutectic cast iron5.过共晶铸铁：Hypereutectic cast iron6.灰铸铁[片墨铸铁]：Flake graphite cast iron, gray cast iron7.球墨铸铁[球铁]：ductile iron, nodular graphite iron, spheroidalgraphite cast iron8.高韧性球墨铸铁：High ductility nodular graphite iron9.中锰球墨铸铁：Medium manganese ductile iron10.中硅球墨铸铁：Medium silicon nodular iron11.可锻铸铁[马铁]：Malleable cast iron12.白心可锻铸铁：White heart malleable cast iron13.黑心可锻铸铁：Black heart malleable cast iron14.花心可锻铸铁：partially graphitized makkeable cast iron15.铁素体可锻铸铁：ferritic malleable cast iron16.珠光体可锻铸铁：pearlitic malleable cast iron17.球墨可锻铸铁：spheroidal graphite malleable cast iron18.蠕墨铸铁[蠕铁，紧密石墨铁]：Vermicular graphite cast iron, compacted graphitecast iron19.白口铸铁：White cast iron20.麻口铸铁：Mottled cast iron21.奥氏体铸铁：Austenitic cast iron22.贝氏体铸铁：bainitic cast iron23.贝氏体球墨铸铁：bainitic ductile cast iron, austferritic ductile castiron24.等温热处理球墨铸铁：austempered ductile iron, ADI25.贝氏体白口铸铁：bainitic white cast iron26.针状铸铁：Acicular cast iron27.马氏体铸铁：martensitic cast iron28.铁素体铸铁：ferritic cast iron29.珠光体铸铁：pearlitic cast iron30.索氏体铸铁：sorbitic cast iron31.合金铸铁：Alloy cast iron32.低合金铸铁：Low alloy cast iron33.铬铸铁：Chromium cast iron34.高铬铸铁：High chromium cast iron35.高硅铸铁：High silicon cast iron36.中硅铸铁：Medium silicon cast iron37.高磷铸铁：High phosphorus cast iron38.铝铸铁：Aluminum cast iron39.高铝铸铁：High aluminum cast iron40.镍铸铁：Nickel cast iron41.硼铸铁：Boron cast iron42.高级铸铁：High grade cast iron43.高强度铸铁：High duty cast iron, high strength cast iron44.工程铸铁：Engineering cast iron45.特种铸铁：Special cast iron46.抗磨铸铁：Abrasion resistant cast iron47.冷硬铸铁[激冷铸铁]：Chilled cast iron48.耐磨铸铁：Wear resisting cast iron49.耐热铸铁：Heat resisting cast iron50.耐蚀铸铁：Corrosion resistant cast iron51.耐酸铸铁：Acid resisting cast iron52.密烘铸铁：Meehanite cast iron53.孕育铸铁：Inoculated cast iron54.总碳量：Total carbon55.碳当量：Carbon equivalent56.碳当量仪：eutectometer57.共晶度：Carbon saturation degree58.硅碳比：Silicon-carbon ratio59.锰硫比：manganese-sulphur ratio60.铸铁石墨形态：Graphite morphology of cast iron61.片状石墨[片墨]：Flake graphite62.球状石墨[球墨]：Nodular graphite, spheroidal carbon63.絮团状石墨[退火t]：Temper graphite, annealing carbon64.团絮石墨：quasi-spheroidal temper graphite65.蠕虫状石墨[蠕墨、紧密石墨]：Compacted graphite, vermicular graphite66.开花状石墨：Exploded graphite67.初生石墨：Primary graphite68.过冷石墨：undercooled graphite69.共晶石墨：Eutectic graphite70.共晶碳化物：Eutectic carbide71.游离碳：Free carbon72.石墨化：graphitizing73.石墨退火化：graphitizing annealing74.石墨化度：graphitizing grade75.石墨化因子：graphitizing factor76.石墨面积率：Percentage of graphite area77.阻碍石墨化元素：hindered graphitizing element78.墨化剂：graphitizer79.石墨球化处理[球化处理]：nodularizing treatment of graphite80.球化率：percent of spheroidization81.石墨球数[球墨数]：number of nodular graphites82.球化剂：nodulizer, nodulizing alloy, spheroidal agent,spheroidizer83.镁焦：magcoke, impregnated coke84.型内球化：in-mold nodularization85.密容加镁包：sealed spheroidizing treatment ladle86.干扰元素：Interference element87.石墨蠕化处理[蠕化处理]：vermiculation of graphite88.蠕化剂：vermicular agent89.蠕化率：percent of vermiculation90.铸铁净化：Purification of cast iron91.三角试块：Wedge test-piece2.4铸造有色合金1.铸造有色合金[铸造非铁合金]：Nonferrous cast alloy2.铸造铝合金：Cast aluminum alloy3.高强度铸造铝合金：High strength cast aluminum alloy4.铝硅合金：Aluminum-silicon alloy5.共晶铝硅合金：Eutectic aluminum-silicon alloy6.亚共晶铝硅合金：Hypoeutectic aluminum-silicon alloy7.过共晶铝硅合金：Hypereutectic aluminum-silicon alloy8.初生硅：Primary silicon phase9.共晶硅：Eutectic silicon phase10.铝镁合金：Aluminum-magnesium alloy11.铝铜合金：Aluminum-copper alloy12.铝锌合金：Aluminum-zinc alloy13.铝锂合金：Aluminum-lithium alloy14.铸造铜合金：Cast copper alloy15.铸造黄铜：Cast brass16.硅黄铜：Silicon brass17.高强度黄铜：High strength brass18.青铜：Bronze19.锡青铜：Tin bronze20.铝青铜：Aluminum bronze21.铅青铜：Lead bronze22.硅青铜：Silicon bronze23.铸造铜铬合金[铬青铜]：Cast copper-chromium alloy24.高阻尼铜合金：High damping copper alloy25.螺旋桨用铸造铜合金：Cast copper alloy for propeller26.铸造镁合金：Cast magnesium alloy27.铸造锌合金：Cast zinc alloy28.低熔点合金：Fusible alloys29.轴承合金[减摩合金]：antifrictional alloys, bearing alloys30.巴氏合金：Babbitt metal, white metal31.钛合金：Titanium alloy32.铸造高温合金：cast superalloy33.镍基铸造高温合金：nickel-base cast superalloy34.蒙乃尔合金：monel metal35.钴基铸造高温合金：cobalt-base cast superalloy36.铁基铸造高温合金：iron-base cast superalloy37.压铸合金：diecast alloy38.压铸铝合金：aluminium alloy39.铸压镁合金：magnesium diecast alloy40.压铸铜合金：copper diecast alloy41.压铸锌合金：zinc diecast alloy42.锌当量：Zinc equivalent2.5熔炼基本术语1.熔炼：Smelting2.熔化率：Melting rate3.熔炼损耗[熔损、烧损]：Total melting loss4.挥发损耗：V olatilizing loss5.元素烧损：Melting of alloying element6.元素增加：Gain of element7.熔池：Bath8.溶剂：Flux9.除气剂：Degassing flux10.覆盖剂：Covering flux11.炉料：Charge12.金属炉料：Metallic charge13.中间合金[母合金]：Master alloy14.回炉料：Foundry returns15.废金属料：Scrap16.炉料计算[配料]：Charge calculation17.熔渣[炉渣]：Slag18.沉渣：Sludge19.浮渣：Cinder, dross, scum20.碱性渣：Basic slag21.酸性渣：Acid slag22.造渣：Slag forming23.出渣：deslagging24.出渣口：Slag hole, slag notch25.炉衬：Furnace lining26.碱性炉衬：Basic lining27.酸性炉衬：Acid lining28.耐火粘土：Fireclay29.碱度[碱性指数]：index of basicity30.补炉：Patching31.炉龄[炉衬寿命]：Furnace campaign32.开炉：Blowing in, power on33.炉内气氛：Furnace atmosphere34.炉气分析：Flue gas analysis35.控制气氛：Controlled atmosphere36.炉前分析：On-the-spot sample analysis37.出炉口：Tap hole38.出炉温度：Tapping temperature39.重熔：remelting40.真空自耗电弧重熔：Consumable electrode vacuum arc refining41.喷射冶金：Injection metallurgy42.区域熔炼：Zone melting43.悬浮熔炼：Levitation melting, suspension melting44.真空熔炼：Vacuum melting45.坩埚炉：Crucible furnace46.坩埚：Crucible, pot47.保温炉：Holding furnace48.反射炉：reverberatory furnace49.感应电炉：Electric induction furnace50.凝壳炉：Skull furnace51.增碳：recarburizing2.6铸钢熔炼1.铸钢熔炼：Smelting of steel2.不氧化熔炼法：Dead melting3.氧化熔炼法：Oxidizing melting4.氧化期[沸腾期]：Oxidizing stage, boil stage5.氧化气氛：Oxidizing atmosphere6.氧化渣：Oxidizing slag7.还原期：Blocking stage, deoxidizing stag8.还原气氛：Reducing atmosphere9.还原渣：Reducing slag10.白渣：White slag11.电弧炉：Electric arc furnace, direct electric arc furnace 12碱性电弧炉：Basic electric arc furnace13.酸性电弧炉：Acid electric arc furnace14.电渣熔炼：Electro-slag melting15.电渣炉：Electro-slag furnace16.氩氧脱碳法[AOD法]：AOD process, Argon-Oxygen Decarburizationprocess17.脱碳：decarburization18.脱氧：deoxidation19.脱氧剂：deoxidizer20.脱磷：dephosphorization21.脱硫desulphurization22.脱硫剂desulphurizer2.7铸铁熔炼1.铸铁熔炼：smelting of cast iron2.双联熔炼：duplexing smelting3.冲天炉：cupola4.大间距双排风口冲天炉：spacious twin-tuyeres cupola,Twin-wind blast system cupola5.多排小风口冲天炉：multiple row small tuyeres cupola6.卡腰冲天炉：Waist shaped cupola7.热风冲天炉：hot blast cupola8.水冷冲天炉：water-cooled cupola9.水冷热风无炉衬冲天炉：hot blast liningless cupola with water cooling10.无焦冲天炉：cokeless cupola11.碱性冲天炉：basic cupola12.酸性冲天炉：acid cupola13.生铁：pig iron14.铸造生铁：foundry pig iron15.焦炭：coke16.铸造焦炭[铸造焦]：foundry coke17.固定碳：fixed carbon18.铁焦比[焦比]：iron coke ratio19.底焦：coke bed20.层焦：coke split21.隔焦：extra split22.接力焦：buffer coke charge23.铁合金：ferro-alloy24.有效高度：effective height25.炉缸：cupola well26.前炉：forehearth27密筋炉胆：ribbed preheating jacket28.出铁槽：cupola spout29.熔化带：melting zone30.风带：air belt, air box, wind box31.风口：tuyere32.风口比：tuyere ratio33.炉壁效应：cupola wall effect34.冲天炉特性曲线：cupola operation chart35.冲天炉炉前控制：front control of molten iron of cupola,inspection in front of cupola36.冲天炉检控仪：tester and controller for cupola melting37.熔化密度：melting intensity38.风量：blast volume39.送风速度：blast intensity40.送风压力：blast pressure41.富氧送风：oxygen enriched blast42.脱湿送风：dehumidification blast43.预热送风：hot blast44.送风预热器：blast preheater45.火花捕集器：spark arrestor46.冲天炉加料机：cupola charging machine47.爬式加料机：skip hoist48.冲天炉自动加料机：automatic cupola charging equipment49.电磁盘：electromagnetic chuck50.电磁配铁秤：electromagnetic weighing balancer51.吸碳：carbon pick-up52.棚料[搭棚]：bridging53.封炉：banking the cupola54.打炉：cupola drop55.碎铁机：breaker2.8金属液处理1.精炼：refining2.真空精炼：vacuum refining3.炉外精炼：ladle refining4.精炼溶剂[精炼剂]：refining flux5.除气[起气]：degassing6.真空除气：vacuum degassing7.吹气净化：blow purifying8.多孔塞法：porous plug process9.变质：modification10.变质剂：modification agent, modificator11.磷变质：phosphorus modification12.钠变质：sodium modification13.长效变质剂：permanent modificator14.型内变质：in-mold modification15.孕育：inoculation16.瞬时孕育[后孕育]：instantaneous inoculation,late stage inoculation, post inculation17.随流孕育：metal-stream inoculation18.型内孕育：in-mold inoculation19.浇口盆孕育：pouring basin inoculation20.孕育剂：inoculant, inoculating agent21.孕育期：inoculation period22.孕育衰退：inoculation fading23.孕育不良：abnormal inoculation, under-inoculation24.合金化处理：alloying treatment25.喂线法[喂丝法]：CQ process, wire feeding process,wire injection process26.摇包：shaking ladle27.电磁搅拌：electromagnetic agitation28.静置：holding, stewing29.扒渣：slagging-off30.型内过滤：in-mold filtering31.型内合金化：in-mold alloying32.晶粒细化：grain refinement33.晶粒细化剂：grain refiner2.9浇注1.浇注：pouring2.保护气氛浇注：pouring under controlled atmosphere3.真空浇注：vacuum pouring4.自动浇注装置：automatic pouring device5.自动浇注机：automatic pouring machine6.电磁浇注机：electromagnetic pouring machine7.捣冒口：churning, pumping8.点冒口[补注]：hot topping up, teeming9.浇包：ladle10.底浇包：bottom pouring ladle11.转运包：transfer ladle12.金属残液：heel13.冷金属：cold metal14.压铁：weight三、造型材料3.1基本术语1.造型材料：molding material2.铸造用砂[砂]：foundry sand, sand3.原砂[新砂]：base sand, new sand, raw sand4.旧砂：used sand5.回用砂：reconditioned sand6.再生砂：reclaimed sand]7.枯砂[焦砂]：burned sand]8.热砂：hot sand9.废砂：waste sand3.2原砂1.标准砂：standard sand2.硅砂[石英砂]：silica sand3.刚玉砂：alumina sand4.镁砂：magnesite sand5.锆砂：zircon sand6.镁橄榄石砂[橄榄石砂]：fosterite sand, olivine sand7.铬铁矿砂：chromite sand8.煤矸石砂：coal gangue sand9.熟料砂：chamotte sand10.炭粒砂：carbon sand11.石灰石砂：limestone sand12.天然砂：natural sand13.人工砂[人造砂]：artificial sand14.水洗砂：washed-out sand15.擦洗砂：scrubbed sand16.浮选砂[精选砂]：floated sand17.松散密度[砂型]：aerated density, riddled sand18.原砂细度[AFS平均细度]：AFS fineness number,fineness number,grain fineness number19.原砂细度[原砂颗粒尺寸]：particle size of base sand20.原砂颗粒分布：grain size distribution of base sand21.原砂角形因数[原砂角形系数，原砂粒形系数]：angularity of base sand22.原砂颗粒形状：grain shape of base sand3.3粘结剂1.粘结剂：binder2.无机粘结剂：inorganic binder3.粘土：clay4.高岭土：kaolin5.膨润土：bentonite6.钠基膨润土：sodium bentonite7.钙基膨润土：calcium bentonite8.活化膨润土：activated bentonite9.有机膨润土：organic bentonite10.有效粘土：effective clay11.活粘土：active clay12.枯粘土（死粘土）：burned clay13.白泥：white clay14.水玻璃粘结剂：sodium silicate binder, water glass binder15.水玻璃波美浓度：Be’concentration of water glass16.水玻璃模数：sodium silicate modulus17.有机粘结剂：organic binder18.纸浆废液[纸浆残液，亚硫酸盐纸浆废液]：lignin liquor19.油类粘结剂：oil based binder20.干性油：drying oil21.合脂粘结剂：synthetic fat binder22.渣油粘结剂：residual oil binder23.自硬粘结剂[冷硬粘结剂]：cold setting binder, no bake binderself-hardening binder24.树脂粘结剂：resin binder25.热固性树脂粘结剂：thermosetting resin binder26.热塑性树脂粘结剂：thermoplastic resin binder27.铸造用树脂：foundry resin28.自硬树脂系[非烘树脂系]：no-bake resin system,self-hardening resin system29.气硬树脂系：gas cured resin system30.热硬树脂系：hot hardening resin system31.呋喃树脂：furan resin32.酚醛树脂：phenol-formaldehyde(PF)resin33.碱性酚醛树脂：alkaline phenolic resin34.糖醇：furfuryl-alcohol35.游离甲醛含量：free formaldehyde content36.游离苯醛含量：free phenol content37.粘结效率：bonding efficiency3.4辅助材料1.型砂附加物：sand addlitives2.煤粉：seacoal3.煤粉代用品：seacoal substitutes4.铸型涂料：dressing mold coating, paint5.砂型涂料：sand coating6.模样涂料：pattern paint7.水基涂料：water-base mold coating8.非水基涂料：non-aqueous coating, non-aqueous paint9.自于涂料：self-drying dressing10.摊开系数[铺展系数]：spreading coefficient11.触变性：thixotropy12.悬浮剂：suspending agent13.分型剂：parting agent14.脱模剂：stripping agent15.固化剂[硬化剂]：hardener16.有机酯：organic ester17.溃散剂：break-down accelerator, break-down agent18.发热剂：exothermic mixture19.冒口覆盖剂：riser cover20.补芯膏：core mud4.5型砂和芯砂1.型砂[造型混合料]：molding mixture, molding sand2.芯砂：core sand3.合成砂：synthetic sand4.粘土砂：clay-bonded sand5.天然型砂[天然粘土砂]：natural molding sand,naturally clay-bonded sand6.红砂：red sand7.面砂：facing sand8.背砂[填充砂]：backing sand9.单一砂：unit sand10.调匀砂：temper sand11.湿型砂：green molding sand, green sand12.煤粉：black sand13.烂泥砂[嘛泥]：loam14.油砂：oil-bonded sand15.合脂砂：synthetic fatty acid bonded sand16.石墨型砂：graphite mold sand17.化学硬化砂：chemical hardening sand18.自硬砂：self-hardening sand, no-bake sand19.水泥砂：cement sand20.水玻璃砂：sodium silicate-bonded sand21.酯硬水玻璃砂：ester cured sodium silicate sand,sodium silicate-ester no-bake sand22.树脂自硬砂：no-bake resin sand,self-hardening resin sand23.呋喃树脂自硬砂：no-bake furan resin sand24.酚醛尿烷树脂自硬砂：pep-set no-bake sand,phenolic resin no-bake sand25.酯固化碱性酚醛树脂自硬砂：ester cured alkaline phenolicresin no-bake sand26.磷酸盐自硬砂：phosphate no-bake sand27.流态砂：castable sand, fluid sand28.气硬砂[冷芯盒砂]：cold box sand, gas hardening sand29.热硬树脂砂：hot hardening resin sand30.覆膜砂：precoated sand, resin coated sand31.壳型（芯）树脂砂：shell mold (core) resin sand32.热芯盒砂：hot box sand33.结球（型砂）：agglomeration (molding sand)3.6型砂性能及试验1.型砂试验：sand testing2.原砂试验：base sand testing3.型砂试样：sand specimen4.型砂膨胀试验：sand expansion testing5.型砂高温试验：elevated temperature testing of sands6.差热分析：differential thermal analysis7.型砂试验仪：sand tester8.铸造用标准筛：standard sieves for foundry9.筛析：screen analysis10.沉降分选：decantation, elutriation11.型砂强度：sand strength12.湿强度：green strength13.干强度：dry strength14.热强度：hot strength15.热湿拉强度：hot wet tensile strength16.风干强度：air dried strength17.型砂韧度：toughness18.破碎指数：shatter index19.起模性：liftability20.表面安定性：surface stability index(SSI)21.残留强度：retained strength22.溃散性：collapsibility23.落砂性：knockout capability24.砂型（芯）硬度：mold hardness25.紧实度：degree of ramming26.紧实率：compactability27.舂实性：rammability28.流动性（砂）：flowability(sand)29.成型性：moldability30.孔隙率：porosity31.透气孔：permeability32.发气量[发气性]：gas evolution33.发气率[发气速度]：gas evolution rate34.退让性[容让性]：deformability rate35.热变形[型砂]：hot deformation (mold sand)36.吸湿性：moisture absorption37.粘模性：stickiness38.保存性（型砂）：preservability(mold sand)39.可使用时间：bench life, working time40.型砂耐火度：refractoriness of molding sand41.微粉含量：micro-grains content42.含泥量：clay content43.含水量[水分]：moisture content44.型砂酸碱度值[型砂pH值]：pH value of sand45.酸耗值：acid demand value46.灼烧减量[灼减]：loss on ignition47.型砂缺陷倾向：defect tendency of molding sand48.胶质价：colloid index49.膨润值：swelling value50.膨胀指数：swelling index51.吸蓝量试验：methylene blue value test52.有效膨润土量：effective bentonite content53.耐用性[复用性]：durability54.涂刷性：brushability55.覆膜砂熔点：melting point of precoated sand四、铸造工艺设计及工艺装备4.1基本术语1.铸造性能：castability2.流动性(金属)：fluidity(metal)3.充型能力：mold-folling capacity4.充型流速[浇注]：delivery rate, pouring rate5.充型时间：filling time6.浇注温度：pouring temperature7.比浇注速度：specific pouring rate8.浇注时间：pouring time9.平衡分配系数：equilibrium distribution,equilibrium partition ratio10.凝固：solidification11.凝固温度范围：solidification range12.凝固时间：solidification time13.均衡凝固：proportional solidification14.同时凝固：simultaneous solidification15.顺序凝固[方向凝固]：directional solidification16.无溶质再分配凝固[无偏析凝固]：partitionless solidification,segregationless solidification17.收缩：contraction18.液态收缩：liquid contraction19.凝固收缩：solidification contraction20.固态收缩：solid contraction21.液-固收缩：liquid-solid contraction22.自由收缩：free contraction23.受阻收缩：hindered contraction24.收缩余量：shrinkage allowance25.缩前膨胀[共晶石墨化膨胀]：eutectic graphitizing expansion26.收缩应力：contraction stress27.热应力：thermal stress28.相变应力：phase change stress,transformation stress29.铸造应力：casting stress30.残留应力[残余应力]：residual stress31.合金线收缩率[自由线收缩率]：alloy linear contraction,free linear contraction coefficient 32.铸件线收缩率：casting linear contraction coefficient,casting linear shirinkage coefficient 33.热裂倾向性：tendency to hot tearing4.2铸件工艺设计1.铸造工艺设计：casting process design2.铸造工艺计算机辅助设计[铸造工艺CAD]：computer-aided design of the castingprocess, casting process CAD3.实体造型：constructive soild geometry,solid modeling4.充型分析：mold filling analysis5.铸造工艺装备设计：foundry tools design6.铸造工艺图：foundry molding drawing7.铸造工艺卡：foundry process card8.铸型装配图：mold assembly drawing9.铸件图[毛坯图]：mold assembly rough casting10.铸造工艺设备：preparation for casting technique11.铸件设计：casting design12.铸件基准面：reference face for machining of casting13.铸合结构：cast fabricated constructure14.分型面：mold joint, mold parting, parting face15.不平分型面：irregular joint, irregular parting,match parting16.阶梯分型面：stepped joint, stepped parting17.过渡角：transition angle18.分型负数：joint allowance, parting allowance19.浇注位置：pouring position20.工艺补正量：design modification, molding allowance21.吃砂量：mold thickness22.补贴：pad23.交接壁：intersection24.十字交接[Ⅹ形交接]：x-junction25.内圆角[圆角]：fillet26.热节：hot spot27.铸筋[铸肋]：ribs28.加强筋[加强肋]：stiffening ribs29.冷铁：densener, chill30.外冷铁：surface densener31.内冷铁：internal densener32.暗冷铁：coated chill, indirect chill33.强制冷却：forced cooling34.起模斜度：pattern draft35.上型[上箱]：cope, top part36.下型[下箱]：bottom part, drag37.型冷时间：mold cooling time38.型腔：mold cavity39.造型余量：molding allowance40.砂芯设计：sand core design41.芯头：core print42.芯头间隙：core print clearance43.芯头斜度：core taper44.芯座：core seat45.定位芯头：locating print46.加大芯头：enlarged core print,strengthened core print47.工艺孔：technological hole48.铸件凝固数值模拟：numerical simulation of casting solidification49.前处理：pre-processing50.潜热处理：latent heat treatment51.网格剖分：enmeshment, mesh generation4.3浇冒口系统1.浇注系统：gating system, running system2.浇注系统设计：design of gating system3.浇道比：gating ratio4.封闭式浇注系统：choked running system, pressurized gatingsystem5.半封闭式浇注系统：enlarged runner system6.开放式浇注系统：non-pressurized gating system,unchoked running system7.阶梯式浇注系统：step gating system8.缝隙式浇注系统：slot gate system9.离心集渣浇注系统：whirl gate dirt trap system10.阻流浇注系统：choked runner system11.冒口浇注系统：feeder head gating, riser gating12.顶注式浇注系统：top gating system13.雨淋式浇注系统：shower gate system14.底注式浇注系统：bottom gating system15.中注式浇注系统：parting-line gating system16.垂直浇注系统：vertical gate system17.等流量浇注系统：equal-volume pressurized system,flow-rate equalized gating18.阻流截面：choked area19.大孔出流：large orifice discharge20.浇口盆[外浇口]：pouring basin21.浇口塞：blanking-off plug22.浇口杯：pouring cup23.直浇道：sprue24.直浇道窝：sprue base25.横浇道：runner26.集渣横浇道：skim runner27.集渣装置（浇注系统）：dirt traps ( in gating system )28.反应室（浇注系统）：reaction chamber ( in gating system )29.内浇道：ingate30.压边浇口：lip runner, kiss runner31.牛角浇口：horn gate32.挡渣片：baffle core33.过滤片[过滤网]：filter screen, strainer core34.冒口：riser, feeder head35.明冒口：open riser36.暗冒口：blind riser37.侧冒口：side riser38.热冒口：hot riser, hot top39.保温冒口：insulating riser40.发热冒口：exothermic riser41.电热冒口：electric arc feed42.压力冒口：pressure riser43.发气压力冒口：gas-delivered pressure riser44.大气压力冒口：atmospheric riser45.易割冒口：knock-off head46.离心集渣冒口：whirl-gate riser47.冷冒口：cold riser48.出气冒口[出气口]：flow off, pop, riser vent, whistler49.冒口设计：riser design50.内接圆法：inscribed circle method51.模数计算法（冒口）：moduli calculation method52.周界商：perimetrischen quotient53.冒口效率：riser efficiency54.补缩：feeding55.有效补缩距离：effective feeding distance,feeding zone56.补缩通道：feeding channel57.反补缩：inverse feeding58.冒口根：riser pad59.冒口颈：riser neck60.冒口圈：feeder bush, riser bush61.冒口套：heat insulating feeder sleeve62.冒口窝：riser base63.冒口高度：riser height64.易割片：knockoff core, washburn core4.4铸造工艺设备1.铸造工艺设备：foundry tools equipment2.模板：pattern plate3.组合模板：composite pattern plate4.双面模板：match plate5.单面模板：single face pattern plate6.模板图：pattern plate drawing7.模板设计：pattern plate design8.缩尺[模样工放尺]：pattern-maker＇s rule ,shrinkage rule9.放样[伸图]：hot dimensional drawing, layout10.模底板：pattern mounting plate11.模样[铸模、模]：pattern12.祖模：grand master pattern13.母模：master pattern14.金属模：metal pattern15.木模：wooden pattern16.石膏模：plaster pattern17.塑料模：plastic pattern18.骨架模：skeleton pattern19.单位模：loose pattern20.整体模：one-piece pattern, solid pattern21.分块模[分开模]：loose pattern, split pattern22.分模面：parting line23.模样分级：pattern classification24.活块：loose piece25.砂箱：flask, molding box26.组合砂箱：built up molding box27.砂箱设计：flask design28.套箱：mold jacket29.套销：hollow pin, stub pin30.箱带[箱挡]：cross bar, flask bar31.芯盒：core box32.芯盒设计：core box design33.芯盒图：core box drawing34.对开芯盒：half core box35.脱落式芯盒：troughed core box36.分盒面：parting of core box五、砂型铸造5.1砂处理1.型砂制备[砂处理]：sand preparation2.型砂质量控制：sand quality control3.型砂水分控制设备：automatic moisture controller of sand4.旧砂处理：sand reconditioning5.旧砂再生：sand reclamation6.旧砂热法再生：thermal reclamation of used sand7.旧砂湿法再生：wet reclamation of used sand8.旧砂干法再生：dry reclamation of used sand9.旧砂回用率：reusable rate of used sand10.砂冷却：sand cooling11.热砂冷却装置：hot sand cooler12.砂温调节器：sand temperature modulator13.冷却提升机：coolelevator, cooling elevator14.热气流烘砂装置：hot pneumatic tube drier15.沸腾床：fluidized bed16.滚筒筛：rotary screen, drum screen17.磁力滚筒：magnetic separator18.滚筒破碎筛：drum breaking screen19.筛砂机：riddle20.原砂擦洗机：sand scrubber21.轮碾机：roller22.配砂：formulation of sand mixture23.预混：premixing24.混砂：sand mixing, sand mulling25.混砂机：sand mixer, sand muller26.连续混砂机：continuous sand mixer27.碗形混砂机：cup-type sand mixer28.树脂自硬砂混砂机：no-bake resin sand mixer29.松砂：aeration, sand-cutting30.松砂机：aerator, sand cutter31.回性[调匀]（型砂）：homogenization of sand,temper of molding sand 32.除尘器：dust catcher, dust collector5.2造型1.造型：molding2.有箱造型：flask molding3.无箱造型：flaskless molding4.手工造型：hand molding5.机器造型：machine molding6.地坑造型：pit molding7.地面造型：floor molding8.叠箱造型：stack molding9.多箱造型：multiple-part molding10.两箱造型：two-part molding11.假箱造型：oddside molding12.劈箱造型：split box molding13.脱箱造型：removable flask molding14.刮板造型：sweep molding15.抛砂造型：impeller ramming,sand slinging molding16.漏模造型：stripping plate molding17.模板造型：pattern plate molding18.实物造型：machine part reproduced molding19.组芯造型：core assembly molding20.微振压实造型：vibratory squeezing molding21.高压造型：high pressure molding22.射压造型：injection and squeeze molding23.负压造型[真空密封造型，V法造型]：vacuum molding24.气冲造型：air impact molding25.静压造型：air-flow press molding,static pressure molding26.切削造型法：molding with molding27.自硬砂造型：self-curing sand molding,self-hardening sand molding28.流态砂造型：fluid sand molding29.造型机：molding machine30.造型线：molding line31.高压造型机：high pressure molding machine32.多触头高压造型机：equalizing piston squeezer33.震实造型机：jolt molding machine34.震压造型机：jolt-squeeze machine35.微振压实造型机：shockless jolt squeeze molding machine,vibratory squeezer36.压实造型机：squeezing molding machine37.射压造型机：shooting and squeezing molding machine38.气冲造型机：air impact molding machine39.水平分型脱箱造型机：horizontal parting flaskless moldingmachine40.多工位造型机：multiple station molding machine41.抛砂机：sand slinger42.震击台[震实台]：bumper43.振动台：vibrating table44.填砂：mold-filling45.辅助框[填砂框]：prefiller46.紧实[紧砂]：compacting47.震实：jolt compacting48.压实：squeezing compacting49.高密度紧实法：high density compaction50.舂砂：ramming51.预紧实：precompact52.砂床：sand bed53.铸坑：casting pit54.吊砂：cod55.塞砂：tucking56.造型工具：hand tools of molding57.修型：patching58.修型工具：mending tools59.砂舂：sand rammer60.镘勺[镘刀]：trowel61.提钩：cleaner62.砂钩：lifter63.通气针：vent wire64.刷水：swabbing65.水笔：swab66.起模：stripping67.起模机：drawing68.起模时间：stripping time69.漏模：pattern stripping70.敲模：rapping71.刮砂：strike-off72.合型[合箱]（砂型铸造）：mold assembling, closing (sand molding )。

铸造学专业英语词汇铸造学专业英语词汇铸造是人类掌握比较早的一种金属热加工工艺，已有约6000年的历史。

以下是为大家分享的铸造学专业英语词汇，供大家参考借鉴，欢迎浏览!碱性熔铁炉 basic cupola碱性熔渣 basic slag碱性生铁 basic pig iron碱性氧化物 basic oxide碱性氧气吹炼法 basic oxygen process碱性造渣法 basic slag practice碱性砖 basic brick渐进时效 progressive aging键形进模口 key gate溅铁 iron spillage僵土 dead clay浆 slurry降伏点，屈服点 yield point降伏强度 yield strength交流电精密仪器接机 alternate current welder交替浸渍试验 alternate immersion test焦[炭]头 ashy top焦块粒度 coke size焦炭比，煤焦比 coke ratio焦炭粉，煤焦粉 coke powder焦炭炉，煤焦炉 coke furnace焦炭生铁，煤焦生铁 coke pig iron焦油 tar焦油白云石砖 tar dolomite brick浇杯 pouring cup浇池 pouring basin浇出嘴(斗、桶、埚、炉） pouring lip浇道 pouring gate浇道棒 runner stick浇道比 runner ratio浇道废料 runner scrap浇道接种法 mold inoculation浇道系连结模型 pattern incorporating the runner system 浇道砖 cluster bottom mold，runner core浇斗，糊料 ladle cement浇斗，浇桶，盛桶 ladle浇斗柄，浇斗抬架 shank浇斗车 ladle car浇斗车 ladle on wheels浇斗抬架 ladle carrier浇斗嘴 lip浇斗，浇桶 pouring ladle浇斗覆盖草灰 limmer浇斗瞬间接种法 instantaneous ladle inoculation浇口，进模口 gate浇口棒 gate stick浇口杯 sprue cup浇口发热剂 pouring gate feeding compound 浇口剖面积，进模口剖面积 gate area浇口切断 gate cutting浇口切断 sprne shearing浇口切断机 gate cutter浇口切断机 gate cutting machine浇口套筒(压铸) sprue bush浇口箱 runner box浇流系方案 gating system plan浇流系统 gating system浇满 gating with run-of浇冒口布置 running and feeding layout浇冒口方案(美) gating and risering(us)浇冒口方案(英) gating and feeding(gb)浇冒口切断机 sprue cutter浇冒口系统 running and feeding system浇皿，浇碟 pouring dish浇套，浇杯 pouring bush浇桶 foundry ladle浇桶(半)取样 ladle sampling浇桶(斗)车 ladle bogie浇桶(斗)挂起梁 ladle bail浇桶(斗)架 ladle chair"浇桶(斗)浇完时间 ladle emptying time浇桶(斗)浇完时间 ladle pouring time浇桶(斗)取样分析 ladle analysis浇桶(斗)容量 ladle capacity浇桶(斗)剩料 ladle residues浇桶(斗)试验 ladle ttest浇桶(斗)抬架 ladle shank浇桶(斗)液面遮盖 ladle covering compound浇桶(斗)预热器 ladle preheater浇桶(斗)嘴 ladle lip浇桶粑 skull浇桶吊车 ladle crane浇桶接种法，浇斗接种法，取熇接种法吊 ladle inoculation 浇桶抬架 carrying tongs浇桶置冲法 open ladle method浇桶砖 ladle brick浇桶转浇 reladle浇铸(浇钢锭) teeming浇铸，浇注 pouring浇铸不到(铸疵) short run浇铸不足(铸疵) poured short浇铸不足(铸疵) short pours浇铸操作 pouring operation浇铸过程 casting cycle浇铸区 casting area浇铸区 casting bay浇铸设备 casting equipment浇铸时间 casting time浇铸时间 pouring time浇铸速率 casting rate。

机械铸造英语词汇及句法翻译 Machine Casting Vocabulary and Syntax Translation 机械铸造英语词汇及句法翻译中文 1000字1. Casting - 铸件/铸造2. Mold - 模具3. Foundry - 铸造厂4. Melting - 熔化5. Pouring - 浇注6. Solidification - 凝固7. Cooling - 冷却8. Shakeout - 摇落9. Cleaning - 清理10. Machining - 机加工11. Defect - 缺陷12. Core - 芯子13. Draft - 倾斜14. Gate - 浇口15. Parting line - 分型线16. Riser - 浇冒17. Sprue - 断道18. Sand - 砂料19. Sand casting - 砂铸造20. Die casting - 压铸21. Investment casting - 熔模铸造22. Gravity casting - 垂直铸造23. Centrifugal casting - 离心铸造24. Permanent mold casting - 半永久模铸造25. Tolerance - 公差26. Dimension - 尺寸27. Surface finish - 表面处理28. Porosity - 孔隙率29. Inclusion - 夹杂物30. Sand mold - 砂模31. Die mold - 压模32. Investment mold - 熔模33. Core sand - 芯砂34. Green sand - 粘性砂35. Sand binder - 砂粘剂36. Casting defect - 铸造缺陷37. Cavity - 腔体38. Hot cracking - 热裂纹39. Cold shut - 冷隔离40. Shrinkage - 收缩41. Mold release - 模具释放剂42. Runner - 导道43. Cope - 上模44. Drag - 下模45. Tapping - 蓄能46. Core removal - 芯子取出47. Finishing - 完工48. Flash - 毛刺49. Sandblasting - 喷砂50. Grinding - 磨削。

常用铸造词汇的中英文对照和解释1. 铸件后处理(post treatment of casting) [ 铸件] 对清理后的铸件进行热处理﹑整形﹑防锈处理和粗加工的过程。

铸件后处理是铸造生产的最后一道工序。

2. 铸件清理(cleaning of casting) [ 铸件] 将铸件从铸型中取出﹐清除掉本体以外的多余部分﹐并打磨精整铸件内外表面的过程。

主要工作有清除型芯和芯铁。

3. 铸造有色合金(cast non ferrous alloy) [ 铸造合金] 用以浇注铸件的有色合金(见有色金属)﹐是铸造合金中的一类。

主要有铸造铜合金﹑铸造铝合金﹑铸造镁合金等。

4. 浇注系统(gating system) [ 铸型] 为将液态金属引入铸型型腔而在铸型内开设的信道。

包括﹕浇口杯，直浇道，横浇道，内浇道。

5. 模样(pattern) [ 铸型] 仿真铸件形状形成铸型型腔的工艺装备或易耗件。

为保证形成符合要求的型腔﹐模样应具有足够的强度﹑刚度。

6. 冒口(riser) [ 铸型] 为避免铸件出现缺陷而附加在铸件上方或侧面的补充部分。

在铸型中﹐冒口的型腔是存贮液态金属的容器。

7. 芯盒(core box) [ 铸型] 将芯砂制成型芯的工艺装备。

可由木材﹑塑料﹑金属或其它材料制成。

8. 芯砂(core sand) [ 造型材料] 铸造生产中用于制造型芯的材料﹐一般由铸造砂﹑型砂黏结剂和辅加物等造型材料按一定的比例混合而成9. 型砂(molding sand) [ 造型材料] 在砂型铸造中用来造型的材料。

型砂一般由铸造砂﹑型砂黏结剂和辅加物等造型材料按一定的比例混合而成。

10. 型砂粘结剂(molding sand binder) [ 造型材料] 将松散的铸造砂粘结在一起使之成为型砂或芯砂的造型材料。

11. 再生砂(reclaimed sand) [ 造型材料] 铸造生产中经过处理基本上恢复了使用性能可以回用的旧砂。

机械铸造英语词汇及句法翻译机械铸造是指使用机械设备和工具进行铸造的过程。

以下是一些常用的机械铸造英语词汇及句法翻译：1. Foundry - 铸造厂2. Casting - 铸件3. Mold - 模具4. Core - 芯子5. Melting - 熔化6. Pouring - 浇铸7. Cooling - 冷却8. Shakeout - 抖砂9. Cleaning - 清理10. Finishing - 整理11. Sand - 砂模12. Binder - 粘结剂13. Sand mixture - 砂浆14. Sand box - 砂箱15. Sprue - 浇注道16. Riser - 铸造孔17. Vents - 通风孔18. Shrinkage - 收缩19. Dross - 渣滓20. Defects - 缺陷21. Die - 模具22. Pattern - 主模23. Core box - 芯盒24. Gate - 浇口25. Runner - 浇注道26. Cavity - 腔体27. Fillet - 圆角28. Draft - 脱模锥度29. Parting line - 分型线30. Ejector pins - 弹簧顶针31. Ejection system - 弹射系统32. Sand inclusion - 砂掺杂33. Porosity - 孔隙率34. Dimension - 尺寸35. Tolerance - 公差36. Surface finish - 表面处理37. Roughness - 粗糙度38. Machining - 机械加工39. Drilling - 钻孔40. Boring - 镗孔41. Milling - 铣削42. Grinding - 磨削43. Polishing - 抛光44. Assembly - 组装45. Welding - 焊接46. Riveting - 铆接47. Brazing - 焊锡48. Inspecting - 检查49. Quality control - 质量控制50. Non-destructive testing - 无损检测。

铸造专业术语英文
铸造 (foundry) 是一种将熔化金属或其他材料倒入模具中，然后使其凝固和冷却以获得所需形状和尺寸的制造过程。

铸造是一种广泛应用的制造技术，用于制造各种零件和设备，例如汽车发动机零件、飞机部件、船舶零件、计算机零件和电子设备组件等。

以下是一些铸造专业术语的英文:
1. Foundry - 铸造厂
2. Furnace - 熔炉
3. Mold - 模具
4. Torch - 熔炉炬
5. Furnace gas - 熔炉气体
6. Iron ore - 铁矿石
7. Coal - 煤
8. Coke - 焦粉
9. Dross - 金属氧化物
10. Foundry process - 铸造过程
11. billet - 铸件
12. casting - 铸件
13. gating - 浇口
14. Shell - 壳模
15. foundry equipment - 铸造设备
16. float - 浮砂
17. draw - 拉砂
18. blow - 吹砂
19. malleable iron - 可铸铁
20. Hardened steel - 硬化钢
这些专业术语对于铸造工人、工程师和研究人员来说非常重要，因为它们用于描述铸造过程中的各种步骤和材料。

铸造实用词汇(英文)————————————————————————————————作者：————————————————————————————————日期：21. charging mixture (配料)2. gas vent (通气孔)air vent (通气孔)3. alcohol base wash (酒精基涂模剂)4. alloy (合金)alloy cast iron (合金铸铁)5. anchor pin (定位销)6. annealing (退火)annealing furnace (退火炉)7. arc welding (电弧熔接)8. as cast (铸胚/毛胚铸件)9. atmospheric core / pencil core(砂心/ 增压/透气砂心)10. bath analysis (炉前分析)11. hand molding (手工造模)12. bending strength (抗弯强度)13. bending test (弯曲试验)14. binder (黏结剂)15. furan resin夫喃树脂16. blow hole / gas hole (气孔) 17. Brinell hardness (布氏硬度)18. brittleness (脆性)19. broken casting at gate / riser or vent(铸件破损)去除浇口, 冒口, 溢流口时, 一起将铸件主体部分也去除的破坏缺陷20. case hardening (表面硬化)21. pouring / pour / cast (浇铸/浇注)22. castability (铸造性)23. casting design / casting plan (铸造方案)24. cast iron / iron castings (铸铁)25. cavity (缩孔)26. ceramic core (陶瓷砂心)27. ceramic filter (陶瓷过滤片)28. ceramic tube (陶管)29. chaplet (砂心撑)30. chill (冷硬/冷激)31. chiller / densener (冷铁)32. chunky graphite (块状/短小石墨)33. clay (黏土)34. riser(冒口)35. coat/mold wash/facing material (涂料/涂模剂)36. washing / coating (涂模/上涂料)37. cold junction (冷接点)38. composites / composite material (复合材料)sand mill / sand mixer (混砂机)sand mixing (练砂)sand mold (砂模)39. contraction / shrinkage (收缩/缩孔/疏松)40. conveyor (输送机)41. core assemble (组合砂心)44. core box (砂心盒)45. core grid / rodding (砂心骨)46. core making machine (砂心机)47. lifting / raised mold / core raise (砂心上浮)48. core washing (砂心涂料)49. corrosion (腐蚀)50. crack (裂痕)=龟裂51. crystal (晶体)52. curing (硬化)53. cut (冲砂)=冲蚀354. metallic pattern (金属模)55. galvanizing (镀锌)56. dirt / scum / dross / slag (熔渣/ 浮渣/ 炉渣)57. sprue / down sprue / down gate (下浇道/ 竖浇道)58. draft (拔模斜度)59. drag (下模/下砂箱/下模箱)60. dressing / cleaning (上涂料/涂料/清理)61. electric furnace (电炉)62. electron microscope (电子显微镜)63. elongation (伸长/伸长率)64. etching solution/etching agent/etchingreagent (浸蚀液)65. open shrinkage / external shrinkage (外缩孔)66. ferritic spheroidal graphite cast iron(肥粒体球状石墨铸铁)67. ferrite (肥粒铁)68. machining allowance / finishing allowance (加工余量)69. flake graphite cast iron (片状石墨铸铁) 70. flow chart (流程图)71. CE meter (热分析)72. full size /full dimension (全尺寸)73. graphitic carbon / graphite carbon (石墨碳)74. gray cast iron (灰口铸铁/普通铸铁/片状石墨铸铁)75. green sand mold (湿砂模)76. hardener / hardening agent (硬化剂)77. hardness test (硬度试验)78. high frequency electric induction furnace (高周波感应电炉)79. holding furnace (保温炉)80. impact test (冲击试验)81. Charpy impact test（夏比冲击试验）82. impact value (冲击值)83. indirect chiller (间接冷铁)84. inlet / pouring basin / pouring cup (浇杯)85. Inoculant (接种剂)86. Inoculation (接种)87. ladle（浇包/浇桶/铁水包）88. molding flask (砂箱)89. joint surface (合模面)90. keel block (Y型试块)91. knock-out / shake-out (清箱/开箱)92. low frequency induction furnace (低周波感应电炉)93. liquid penetrant testing (渗透探伤试验/PTtest)94. low temperature annealing (低温退火)95. magnetic powder test (MT/磁粉探伤)96. melting furnace (熔解炉)97. metal flask (金属砂箱)98. metallographic microscope (金相显微镜)99. metallography (金相学)100. parting line (分模线).101. parting plane（分割面）102. pattern (模型/模具)103. pattern coating (模型涂漆)104. pearlite (波来铁)105. burn on / sand burning (烧结/结砂)4106. pig iron (生铁)107. scrap steel (废钢)108. pin hole (针孔)109. pore (气孔)110. porosity (多孔性/气孔率)111. pouring rate (浇铸速度)112. pouring temperature (浇注温度)113. pouring time (浇注时间)114. pouring weight (浇注重量)115. quality control (质量管理)116. X-ray inspection / radiography (X线探伤) 117. rapping (起模)118. ratio of graphite spheroidization (球化率) 119. rejected castings (不良品)120. residual stress (残留应力/铸造应力) 121. roll over machine (翻转机)122. sag core (砂心下垂)123. sand blast (喷砂)124. sand inclusion (夹砂)125. short pours / short run (浇注不足) 126. shot blast (抛丸)127. shrinkage cavity (缩孔)128. shrinkage crack (缩裂)129. s lag off agent / slag disposal agent (除渣剂)130. s lag inclusion (夹渣)131. s olidification time (凝固时间)132. s pherodial graphite (球状石墨)133. s pheroidizing agent (球化剂)134. strength test (强度试验)135. stress concentration (应力集中)136. stress relief (应力消除)137. rough surface (表面粗糙)138. surface fold / gas run (皱皮/流缝/冷隔)139. surface roughness (表面粗糙度)140. surface treatment (表面处理)141. tensile strength (抗拉强度)142. tensile test (拉伸试验)143. test piece/test lug (试片)144. used sand (旧砂)145. working reference point (加工基准)146. Ultrasonic testing (UT/超声波检测)147. Gating system （浇注系统）148. test coupon （试棒）149. Non-destructive testing (NDT/非破坏性测试)150. Visual inspection (VT/目测)151. rough machining (粗加工)152. finishing machining（精加工）153. Non conformity report (NCR 不符合报告)154. Corrective action report (改善措施报告)155. solidification simulation (凝固模拟)5。

常用铸造术语中英对照2021-6-26整理(BY BARRY)Ⅰ.根本术语1.压力铸造die casting2.铸造casting,foundry,founding3.铸件casting4.毛坯铸件rough casting5.试制铸件pilot casting6.试模trial shot7.模具mold,mould8.压铸机die casting machine9.铸造设备foundry equipment,foundry facilities10.铸工caster,founder,foundry worker11.压铸工die carter12.铸造厂foundry13.铸造车间foundry shop14.铸造工作者foundry man15.批〔batch一批:a batch;每批:each batch, per batch);lot16.一炉a cast,a heat,a melt17.焊接welding18.铸造三废foundry effluent19.铸锭ingotⅡ.铸造合金、熔炼和浇注1.铸造合金cast alloy2.铝合金aluminium alloy3.铸造复合材料cast composite4.合金元素alloy element5.杂质元素tramp element6.碳化物carbide7.过热superheating8.过冷supercooling9.熔点melting point10.总碳量total carbon11.碳当量carbon equivalent12.碳当量仪eutectometer13.铝硅合金aluminium-silicon alloy14.压铸合金die cast alloy15.压铸铝合金aluminium diecast alloy16.压铸镁合金magnesium diecast alloy17.熔炼smelting18.熔化率melting rate19.元素增加gain of element20.熔剂flux21.熔池bath22.除气熔剂degassing flux23.覆盖剂covering flux24.炉料charging25.金属炉料metallic charging26.回炉料foundry returns 27.废金属料scrap28.熔渣slag29.沉渣sludge30.浮渣dross,scum,cinder31.造渣slag forming32.出渣deslagging33.出渣口slag hole34.炉衬furnace liner35.出炉口tap hole36.出炉温度tapping temperature37.重熔remelting38.坩埚炉crucible furnace39.保温炉holding furnace40.精炼refining41.真空精炼vacuum refining42.除气degassing43.残料heel44.浇注pouring45.自动浇注装置automatic pouring device46.浇包，料斗(勺)ladle47.转运包transfer ladle48.金属残液heel49.冷金属cold matelⅢ铸造工艺与工艺设备die casting process and process device1.铸造性能castability2.流动性fluidity3.充型能力mold-filling capacity4.充型速度(浇注速度)pouring rate;delivery rate5.充型时间filling time6.浇注温度pouring temperature7.比浇注速度specific pouring rate8.浇注时间pouring time9.凝固solidification10.凝固时间solidification11.收缩contraction;shrinkage12.收缩率shrinkage13.液态收缩liquid contraction14.凝固收缩solidification contraction15.固态收缩solid contraction16.液-固收缩liquid-solid contraction17.自由收缩free contraction18.收缩余量shrinkage allowance19.收缩应力contraction stress20.热应力thermal stress21.铸造应力casting stress22.残留应力(剩余应力)residual stress23.热裂倾向性tendency to hot tearing24.铸造工艺设计casting process design25.铸造工艺计算机辅助设计Computer-aided design for the casting process;casting process CAD26.实体造型constructive solid geometry;solid modeling27.充型分析mold filling analysis28.铸造工艺设备设计foundry tools design29.铸造工艺卡casting process card;foundry process card30.铸型装配图mold assembly drawing31.铸件图(毛坯图)drawing of rough casting32.铸造工艺准备preparation of casting technique33.铸件设计casting design34.铸件基准面reference face for machining of casting35.分型面parting face;(mold joint;mold parting)36.不平分型面irregular parting;(irregular joint;match parting)37.阶梯分型面stepped parting;stepped joint38.浇注位置pouring position39.交接壁intersection40.十字交接X-junction41.圆角fillet42.热节(点)hot spot43.加强筋stiffening ribs44.拨模斜度draft45.型腔mold cavity46.工艺孔technological hole47.浇注系统gating system;running system48.直浇道sprue49.横浇道runner50.内浇口ingate,gate51.溢流槽overflow well52.排气槽air vent53.分流锥sprue spreader;spreaderⅣ压力铸造〔特种铸造〕die-casting1.压铸机die casting machine2.冷室压铸机cold chamber die casting machine3.冷室卧式压铸机(卧式压铸机)horizontal(cold chamber)die casting machine4.冷室立式压铸机〔立式压铸机〕vertical(cold chamber)die casting machine5.热室压铸机hot chamber die casting machine6.真空压铸evacuated die casting;vacuum die casting7.压射injection;shot8.压射机构injection system9.压室injection chamber10.压射冲头injection ram;plunger11.压射速度injection speed12.压射比压injection pressure13.增压pressurization 14.充填率rate of filling15.锁型(合型)die locking16.合型机构(锁型机构)die closing mechanism17.锁型力die locking force;clamping force18.拉杆tie bar;tie rod19.压铸模die;die casting die20.定模(定型)fixed die;cover die half21.动模(动型)moving die;ejection die half22.浇口套sprue bush23.留型时间opening time24.顶出机构ejection mechanism25.顶杆ejector pin26.抽芯机构core puller27.余料biscuit;slug28.压铸涂料coating of diecasting;releaseagent29.充型压力mold filling pressure30.充型速度filling speed31.保压压力dwell pressure32.保压时间dwell timeⅤ压铸后加工及其工具1.喷砂清理sand blasting cleaning2.喷丸清理shot blasting cleaning3.抛丸清理wheel blasting cleaning4.滚筒清理tumbling5.抛丸清理机wheel blasting machine6.除浇口degating;trimming7.除毛刺deburring8.去氧化皮descaling9.打磨grinding10.弹丸shot11.抛丸器shot wheel12.喷丸器shot blaster13.砂轮机grinder14.浸渗处理impregnantion15.浸渗剂impregnant16.矫型rectification;straightening coining;17.外表处理surface treatment18.砂带打磨belt sanding19.钻孔;镗孔boring20.脱脂degreasing21.电镀electroplating;electrostatic coating22.夹具clamp;fixture23.机加工machining24.铣milling25.台式铣床bench milling machine26.数控加工中心CNC27.铸件机加工余量machining allowance of casting28.切削液mineral cutting oil29.抛光polishing30.粗加工rough working31.喷涂painting32.冲孔punching33.外表处理surface treatment34.洗净rinse35.车床lathe36.磨床grinder,grinding machine37.铣床milling machine38.钻床drill press39.刨床planerⅥ检测方式/设备/工具量具inspection equipment/facility1.合格质量水平acceptable quality level(AQL)2.气密性试验air tightness test3.大气暴露试验atmospheric corrosion test4.成分分析试验chemical analysis5.破坏性检测destructive inspection6.非破坏性检测nondestructive inspection7.尺寸检测dimensional test8.硬度试验hardness test9.冲击试验impact test10.逐件检查individual check11.抽样检查sampling inspection12.三座标检测microcode13.耐压试验pressure test14.盐雾试验salt spray test15.盐雾试验机salt spray test machine16.拉力测量机tensile test machine17.平面度检测仪flatness inspection guage18.检漏机leakage test machine19.普通检具normal guage20.抽样检查sampling inspection21.耐气候试验weathering test22.x光探伤x-ray test23.X光机X-ray machine24.塞规plug guage25.丝攻screw tap26.锥度规conical guage27.螺纹塞规thread plug guage28.游标卡尺vernier caliper29.半径规radius guage30.测角器/量角器bevel guage31.测径规,厚簿规calliper guage32.高度尺height guage33.深度尺depth guage34.三座标CMM35.光谱仪spectrographⅦ.包装packaging1.护边edge protection2.中间夹层intermediate layer3.多插入口式托盘multiple-entry pallet4.一次性托盘throw-away pallet5.耐气候wether resistanceⅧ图纸相关Drawing Related1.喷砂清理abrasive cleaning2.研磨剂abrasive3.依据according to/Acc to4.阳极氧化anodic oxidation5.外观appearance6.踏板autowalk pallet7.底座基座基准base8.盲孔blind hole9.气孔,气泡blow hole10.孔径hole diameter11.凸台boss12.基准面datum plane13.模定位面cast locator datum plane14.铸造应变casting strain15.中心孔center bore16.外圆角,倒角chamfer17.内圆角fillet18.同心度concentricity19.平面度flatness20.平行度parallel21.粗糙度roughness22.垂直度perpendicularity23.清洁度cleanness24.符合conform to25.残留物，污物contamination26.抽芯孔,铸孔core hole27.耐腐蚀corrosion resistance28.沉孔counterbore29.盖板cover30.关键尺寸critical dimension31.横切试验cross-cut test32.脱炭decarburize33.拔模斜度draft angle/draft34.导电性electric conductivity35.电动扶梯梯级escalator step36.外径〔大径〕external diameter37.内径(小径)internal diameter38.外螺纹external thread39.加工余量machining allowance40.法兰flange41.披锋flash42.自由状态free state43.通用公差〔未注公差〕general tolerance44.符合in accondance with45.来料检验incoming inspection46.标识indication,marking47.绝缘性isolation characteristics48.金属互化物intermetallic compound49.内螺纹internal thread50.每per51.边缘periphery52.永久伸长permanent stretch53.垂直于perpendicular to54.针孔，销孔pin hole55.平面图plan,plane figure56.磨光剂polish agent57.聚酯纤维polyester58.容许应力proof stress59.剩余应力residual stress60.试生产铸件prototype casting61.质量保证quality assurance62.散热器radiator63.耐磨性resistance to abrasion64.肋；筋条rib65.滚丝攻通roll thread thru66.剖面图section67.模具寿命service life of dies68.螺距pitch69.阴影毛坯区域shaded area cast70.收缩shrink71.缩孔shrinkage porosity72.碎片sliver73.烧伤soldering mark74.标准standard/std.75.强度范围strength division76.分层;剥落stripped mark;peeling77.清理外表;外表加工;外表抛光surface finish78.抗拉强度tensile strength79.未注unless otherwise specified/unspecified/unmarked80.凸纹/直纹vein grain81.壁厚wall thickness82.屈服点yield pointⅨ压铸报价Quotation1.适用检测标准acceptable inspection standard2.压铸附加费additional casting cost3.铸造费用casting cost4.折扣价depreciation expenses5.估价estimated price6.离岸价free on board(FOB)7.到岸价cost insurance freight(CIF)8.信用证letter of credit(LC)9.后加工费finishing cost10.定率法fixed rate method11.先行生产go-ahead of produce 12.铝锭价格ingot price13.插件费insert cost14.检测费inspection cost15.熔炼费melting cost16.制造间接(额外)费overhead manufacturing expense17.附加利益profit added18.废品比例rejection percentage19.废品率standard rejection rate20.报废时价值,剩余价值,剩余价值residual value/scrap value21.机器运转费;机器运营本钱running cost of machine22.卖价selling expense23.销售间接费selling overhead24.寿命service life25.(合金)掺合比例standard alloying ratio26.标准价格standard price27.试铸时间time of trial shot28.总价格total cost29.试铸费trial casting cost30.除浇口费trimming cost31.生产yield32.生产率yield rate33.后加工合格率yield rate of finishing34.熔炼生产率yield rate of melting35.压铸成品率overall yield of castingⅩ压铸质量和缺陷casting quality and defect1.废品reject2.化学成分不合格chemical consistenceabnormal3.飞边joint flash4.毛刺veining;burr5.气孔blowhole6.气泡blister7.气泡bubble8.激冷区chill zone9.冷脆性cold shortness10.冷隔cold shut;cold filling11.裂纹crack12.铸点dot13.花纹flower msrk;stripping for shot blast14.外部材料foreign material。