当前位置：文档之家 › KS0107 KS0108控制的19264液晶驱动程序C51示例

KS0107 KS0108控制的19264液晶驱动程序C51示例

  • 格式：doc
  • 大小：66.50 KB
  • 文档页数：12

下载文档原格式

  / 12

合集下载

C51单片机模块驱动程序参考

C51单片机模块驱动程序参考
{0x30,0x31,0x32,0x33,0x34,0x35,0x36,0x37,
0x38,0x39,0x41,0x42,0x43,0x44,0x45,0x46
};定义在函数外部
unsigned char Key_ASC2(unsigned char key)
{
unsigned char key_asc2;
{
StartI2C();
Write8Bit(0xA2);
ChackAck();
Write8Bit(RomAddress);
ChackAck();
StartI2C();
Write8Bit(0xA3);
ChackAck();
for(;bytes!=1;bytes--)
{
*RamAddress=Read8Bit();
i=*ptr;
i &=பைடு நூலகம்0x80;
if(i==0)
break;
}
}
函数功能描述：向1602指令寄存器写指令；
void WriteW(uint a)
{
ptr=0xAFF0;//RS=0，R/W=0
*ptr=a;
}
函数功能描述：LCD初始化；
void LCD_Init(void)
{
CheckBF();
WriteW(0x38);
函数功能描述：键盘初始化，将标志位置1;
void Key_Init(void)
{
bKeyUp_Flag=1;//标志（全局变量）位置1
}
函数功能描述：键盘扫描函数，得到键的行列位置;
unsigned char GetScanKey(void)
{
unsigned char key, i, temp;

KS0107_KS0108控制器

KS0107_KS0108控制器
* 功能 : 全部清除KS0108显示存储器
* 输入 : 无
* 输出 : 无
***********************************************************************/
void Clr_Screen(void)
{
unsigned char j,k;
{
unsigned char j,k;
CSA=1;
CSB=0;
for(k=hang;k<=hang+1;k++)
{
Write_0108_Reg(Set_Page+k);
Write_0108_Reg(Set_Column);
for(j=0;j<64;j++) Write_0108_Data(0x00);
{
CSA=1;
CSB=0;
}
Write_0108_Reg(0x40+Y);
Write_0108_Reg(0xB8+1+X); //set page address
for(i=0;i<16;i++,p++)
{
if(i==n+1)
{
CSA=0;
* 创建人 ： 银剑
* 创建时间： 2011年11月5日
* 版本号 ： 2.0
* C51编译器 Keil 7.08
* 最高晶振：22.1184M
***********************************************************************/

北京青云液晶屏LCM19264C

北京青云液晶屏LCM19264C
指令/数据选择 当 RS 是 Low 时，MCU 会存取指令数据，而当 RS 是 High 时，MCU 会存取显示 RAM 的数据。 读取/写入信号(R/W)，高电位时表示为读取的动 作，低电位时表示为写入的动作。 E为Enable信号。 R/W 为 L 时，在 E 的下降沿写入数据； R/W为H时，在E为高电平时读出数据；
北京青云创新科技发展有限公司
TEL : 010-62168698
Page 9
北京青云创新
图形点阵模块
LCM19264C
Mar27 ,2006
读操作时序
MPU Read Timing
-------------------------------------------------------------------------------------------------------------------------------------------------
黑白模式（白底黑字，蓝底黑字），6:00 视角，正向显示； 3. LED 背光； 4. 工作电压：5V，工作电流：11mA（典型值）； 5. 控制器KS0108，芯片封装COB。
-------------------------------------------------------------------------------------------------------------------------------------------------
北京青云创新科技发展有限公司
TEL : 010-62168698
Page 8
北京青云创新
图形点阵模块
读写操作时序
LCM19264C
Mar27 ,2006

19264显示驱动程序

19264显示驱动程序

19264控制器KS0108#include <at89x52.h>#include <intrins.h>#include "zimo.h"#define RS P2_6 /*"H" is send or read the data;"L" is the instruction*/ #define RW P3_6#define E P2_5 /*Operation enable*/#define CS1 P2_4#define CS2 P2_3#define CS3 P2_2#define DATA P0#define uchar unsigned char#define uint unsigned int/* -------------------------------------------------Delay some time----------- */void delay10ms(unsigned char x){unsigned char i,j,k;for(i=0;i<x;i++)for(j=0;j<10;j++)for(k=0;k<120;k++);}/* -------------------------------------------------Send the instruction to the First KS0108 window--*/void OutFI(uchar i){unsigned char data_sta;do{E=0;RW=1;RS=0;CS1=0;_nop_();E=1;_nop_();data_sta=DATA;E=0;RW=0;CS1=1;E=1;}while(data_sta&0x80);E=0;RW=0;RS=0;CS1=0;_nop_();E=1;_nop_();DATA=i;_nop_();E=0;RW=1;CS1=1;E=1;}/* ------------------------------------------------- Send the instruction to the Second KS0108 window.--*/void OutSI(uchar i){unsigned char data_sta;do{E=0;RW=1;RS=0;CS2=0;_nop_();E=1;_nop_();data_sta=DATA;E=0;RW=0;CS2=1;E=1;}while(data_sta&0x80);E=0;RW=0;RS=0;CS2=0;_nop_();E=1;_nop_();DATA=i;_nop_();E=0;RW=1;CS2=1;E=1;}/* ------------------------------------------------- Send the instruction to the Third KS0108 window--*/void OutTI(uchar i){unsigned char data_sta;do{E=0;RW=1;RS=0;CS3=0;_nop_();E=1;_nop_();data_sta=DATA;E=0;RW=0;CS3=1;E=1;}while(data_sta&0x80);E=0;RW=0;RS=0;CS3=0;_nop_();E=1;_nop_();DATA=i;_nop_();E=0;RW=1;CS3=1;E=1;}/* -------------------------------------------------Send the data to the First ks0108 Window--*/void OutFD(uchar i){unsigned char data_sta;do{E=0;RW=1;RS=0;CS1=0;_nop_();E=1;_nop_();data_sta=DATA;E=0;RW=0;CS1=1;E=1;}while(data_sta&0x80);E=0;RW=0;RS=1;CS1=0;_nop_();E=1;_nop_();DATA=i;_nop_();E=0;RW=1;CS1=1;E=1;}/* ------------------------------------------------- Send the data to the Second ks0108 Window--*/void OutSD(uchar i){unsigned char data_sta;do{E=0;RW=1;RS=0;CS2=0;_nop_();E=1;_nop_();data_sta=DATA;E=0;RW=0;CS2=1;E=1;}while(data_sta&0x80);E=0;RW=0;RS=1;CS2=0;_nop_();E=1;_nop_();DATA=i;_nop_();E=0;RW=1;CS2=1;E=1;}/* ------------------------------------------------- Send the data to the Third ks0108 Window--*/void OutTD(uchar i){unsigned char data_sta;do{E=0;RW=1;RS=0;CS3=0;_nop_();data_sta=DATA;E=0;RW=0;CS3=1;E=1;}while(data_sta&0x80);E=0;RW=0;RS=1;CS3=0;_nop_();E=1;_nop_();DATA=i;_nop_();E=0;RW=1;CS3=1;E=1;}/* ------------------------------------------------- Read the data to the First ks0108 Window--*//*unsigned char RD_data_F(){unsigned char data_sta;do{E=0;RW=1;RS=0;CS1=0;_nop_();E=1;_nop_();data_sta=DATA;E=0;RW=0;CS1=1;E=1;}while(data_sta&0x80);E=0;RW=1;RS=1;CS1=0;_nop_();E=1;_nop_();_nop_();_nop_();data_sta=DATA;_nop_();E=0;RW=0;CS1=1;E=1;return (data_sta);}/* ------------------------------------------------- Read the data to the Second ks0108 Window--*//*unsigned char RD_data_S(){unsigned char data_sta;do{E=0;RW=1;RS=0;CS2=0;_nop_();E=1;_nop_();_nop_();_nop_();data_sta=DATA;E=0;RW=0;CS2=1;E=1;}while(data_sta&0x80);E=0;RW=1;RS=1;CS2=0;_nop_();data_sta=DATA;_nop_();E=0;CS2=1;E=1;return (data_sta);}/* ------------------------------------------------- Read the data to the Third ks0108 Window--*//*unsigned char RD_data_T(){unsigned char data_sta;do{E=0;RW=1;RS=0;CS3=0;_nop_();E=1;_nop_();_nop_();_nop_();data_sta=DATA;E=0;RW=0;CS3=1;E=1;}while(data_sta&0x80);E=0;RW=1;RS=1;CS3=0;_nop_();E=1;_nop_();data_sta=DATA;_nop_();E=0;CS3=1;E=1;return(data_sta);}/* ------------------------------------------------- Initialize the LCD,The system reset,invoke First time-*/void InitLCD(){OutFI(0x40); /*Set the Y address 0 */OutSI(0x40);OutTI(0x40);OutFI(0xb8); /*Set the Page 0 */OutSI(0xb8);OutTI(0xb8);OutFI(0xc0); /*Set the display start line 0 */OutSI(0xc0);OutTI(0xc0);OutFI(0x3f); /*Display ON */OutSI(0x3f);OutTI(0x3f);}/* -------------------------------------------------Clear the three ks0108's display ram.Clrscr screen-*/void Clrscreen(){unsigned char i,j;for(i=0;i<8;i++){OutFI(0xb8|i);for(j=0;j<64;j++){OutFI(j|0x40);OutFD(0);}}for(i=0;i<8;i++)(OutSI(0xb8|i);for(j=0;j<64;j++)(OutSI(j|0x40);OutSD(0);}}for(i=0;i<8;i++)(OutTI(0xb8|i);for(j=0;j<64;j++)(OutTI(j|0x40);OutTD(0);}}}/* -------------------------------------------------Display Chinese ideograph;x_add is the x address;It has 4 layers,0,1,2,3; Width is the Chinese ideograph width;bmp is the table's name-*/void DrawBmp(uchar x_add,uchar layer,uchar width,uchar *bmp)(unsigned char x;unsigned int i=0;for(x=x_add;x<x_add+width;x++)(if (x>127) /*The Third KS0108*/(OutTI((x-128)|0x40); /*Set the x address*/OutTI(layer|0xb8); /*Set the y address*/OutTD(bmp[i]); /*Send thd data to LCD ram*/OutTI((x-128)|0x40); /*Display the down screen*/ OutTI((layer|0xb8)+1); i++; /*Display zimo table address add 1*/ OutTD(bmp[i]);}else if (x>63) /*The Second ks0108*/{OutSI((x-64)|0x40);OutSI(layer|0xb8);OutSD(bmp[i]);OutSI((x-64)|0x40);OutSI((layer|0xb8)+1);i++;OutSD(bmp[i]);}else /*The First ks0108*/{OutFI(x|0x40);OutFI(layer|0xb8);OutFD(bmp[i]);OutFI(x|0x40);OutFI((layer|0xb8)+1);i++;OutFD(bmp[i]);}i++;}}/* -------------------------------------------------Display Chinese ideograph;x_add is the x address;It has 4 layers,0,1,2,3; Width is the Chinese ideograph width;bmp is the table's name.-*/void DrawBmp_f(uchar x_add,uchar layer,uchar width,uchar *bmp) {unsigned char x;unsigned int i=0;for(x=x_add;x<x_add+width;x++) (if (x>127)(OutTI((x-128)|0x40);OutTI(layer|0xb8);OutTD(~bmp[i]);OutTI((x-128)|0x40);OutTI((layer|0xb8)+1);i++;OutTD(~bmp[i]);}else if (x>63)(OutSI((x-64)|0x40);OutSI(layer|0xb8);OutSD(~bmp[i]);OutSI((x-64)|0x40);OutSI((layer|0xb8)+1);i++;OutSD(~bmp[i]);}else(OutFI(x|0x40);OutFI(layer|0xb8);OutFD(~bmp[i]);OutFI(x|0x40);OutFI((layer|0xb8)+1);i++;OutFD(~bmp[i]);}i++;}}/*Display indention; x_add is the x address;It has 4 layers,0,1,2,3; Width is the Chinese ideograph width-*/void _DrawBmp_(uchar x_add,uchar layer,uchar width){unsigned char x;for(x=x_add;x<x_add+width;x++){if (x>127){OutTI((x-128)|0x40);OutTI(layer|0xb8);OutTD(0);OutTI((x-128)|0x40);OutTI((layer|0xb8)+1);OutTD(0);}else if (x>63){OutSI((x-64)|0x40);OutSI(layer|0xb8);OutSD(0);OutSI((x-64)|0x40);OutSI((layer|0xb8)+1);OutSD(0);}else{OutFI(x|0x40);OutFI(layer|0xb8);OutFD(0);OutFI(x|0x40);OutFI((layer|0xb8)+1);OutFD(0);/* --------------------------------------------------Display indention; x_add is the x address;It has 4 layers,0,1,2,3; Width is the Chinese ideograph width-*/void _DrawBmp_black(uchar x_add,uchar layer,uchar width){unsigned char x;for(x=x_add;x<x_add+width;x++){if (x>127){OutTI((x-128)|0x40);OutTI(layer|0xb8);OutTD(0xff);OutTI((x-128)|0x40);OutTI((layer|0xb8)+1);OutTD(0xff);}else if (x>63){OutSI((x-64)|0x40);OutSI(layer|0xb8);OutSD(0xff);OutSI((x-64)|0x40);OutSI((layer|0xb8)+1);OutSD(0xff);}else{OutFI(x|0x40);OutFI(layer|0xb8);OutFD(0xff);}}OutFI(x|0x40);OutFI((layer|0xb8)+1);OutFD(0xff);}}}/* --------------------------------------------------Display the line display_data_graph is the display graph data-*/void _DrawBmp_line(uchar x_add,uchar layer,uchar width,uchar display_data_graph) {unsigned char x;unsigned int i=0;for(x=x_add;x<x_add+width;x++){if (x>127){OutTI((x-128)|0x40);OutTI(layer|0xb8);OutTD(display_data_graph);}else if (x>63){OutSI((x-64)|0x40);OutSI(layer|0xb8);OutSD(display_data_graph);}else{OutFI(x|0x40);OutFI(layer|0xb8);OutFD(display_data_graph);}i++;/*Display the column display_data_graph is the display graph data-*/void _DrawBmp_column(uchar x,uchar width) {unsigned int i=0;if (x>127){for(i=0;i<width;i++){OutTI((x-128)|0x40);OutTI(i|0xb8);OutTD(0xff);}}else if (x>63){for(i=0;i<width;i++){OutSI((x-64)|0x40);OutSI(i|0xb8);OutSD(0xff);}}else{for(i=0;i<width;i++){OutFI(x|0x40);OutFI(i|0xb8);OutFD(0xff);}}}}}。

19264液晶模块显示51单片机汇编程序

19264液晶模块显示51单片机汇编程序
mov dptr,#table3
call wordw
mov r3,#0b8h ;页地址暂存
mov r4,#70h ;列地址暂存
mov dptr,#table4
call wordw
call select2
mபைடு நூலகம்v r3,#0b8h ;页地址暂存
mov r4,#40h ;列地址暂存
mov com,r4 ;设置起始列为第0列，总共64列
call rswrite
clear1:
mov dat,#00h ;清除显示（清屏）
call datawrite
djnz r2,clear1 ;列循环64列
mov r2,#64
inc r3
setb cs3
ret
select3:
setb cs1
setb cs2
clr cs3
ret
;********************
DELAY10ms: MOV R4,#20
D1: MOV R5,#248
w1:
movc a,@a+dptr
mov dat ,a
call datawrite
inc dptr
djnz county,w1
djnz r5,w2
sjmp w3
w2:
inc r3 ; 页地址增加1
mov com,r3
call rswrite
mov com,r4 ;列地址为原来的
db 82h, 80h,0FFh, 80h, 80h,0C0h, 80h, 00h
db 00h, 00h, 40h, 20h, 18h, 07h, 00h, 00h

19264 程序

19264 程序

/****************************************************************************** *************--------------------------------------------------------------------------------------**** 文件名:**** Copyright (c) 2010-2010 **xxx（中国）电子有限公司研发部**** 创建人: 酥蒸饼**** 日期: 2010.10.07**** 修改人: 酥蒸饼**** 日期: 2010.10.207**** 描述: LCD19264-1 ES-9116控板驱动头文件****** 版本: NO.1****--------------------------------------------------------------------------------------********************************************************************************* ***********/#ifndef _DIY_LCD19264_#define _DIY_LCD19264_#define uchar unsigned char#define uint unsigned int#define DATA_BUFFER P0sbit E=P2^3; //使能端sbit RS=P2^1; //指令数据选择端sbit RW=P2^2; //读写选择信号sbit RST=P2^6; //复位端sbit CS1=P2^7; //左屏片选sbit CS2=P2^5; //中屏片选sbit CS3=P2^4; //右屏片选/*unsigned char bdata Temp_Buffer; //接收字节sbit D_Buf0=Temp_Buffer^0; //Temp_Buffer第0位sbit D_Buf1=Temp_Buffer^1; //Temp_Buffer第1位sbit D_Buf2=Temp_Buffer^2;sbit D_Buf3=Temp_Buffer^3;sbit D_Buf4=Temp_Buffer^4;sbit D_Buf5=Temp_Buffer^5;sbit D_Buf6=Temp_Buffer^6;sbit D_Buf7=Temp_Buffer^7; //Temp_Buffer第7位0////////////////unsigned char bdata Temp_Buffer_1; //接收字节sbit Buf0=Temp_Buffer_1^0; //Temp_Buffer第0位sbit Buf1=Temp_Buffer_1^1; //Temp_Buffer第1位sbit Buf2=Temp_Buffer_1^2;sbit Buf3=Temp_Buffer_1^3;sbit Buf4=Temp_Buffer_1^4;sbit Buf5=Temp_Buffer_1^5;sbit Buf6=Temp_Buffer_1^6;sbit Buf7=Temp_Buffer_1^7; //Temp_Buffer第7位0 *//****************************************************************************** ****************-------------------------------------------------------------------------------------------** 函数名:lcd_busy()** 输入:** 输出:** 功能描述:忙检测** 全局变量:** 调用模块:** 日期:**-------------------------------------------------------------------------------------------******************************************************************************* **************/void lcd_busy(void) //Read State Data function{P0=0Xff;RS=0;RW=1; //读状态条件E=1;// _nop_();while(DATA_BUFFER&0x80); //busy位// _nop_();E=0;}/****************************************************************************** ****************-------------------------------------------------------------------------------------------** 函数名: uchar rd_lcd_data()** 输入:** 输出: RAM数据** 功能描述: 读操作，读液晶屏RAM数据** 全局变量:** 调用模块:** 日期:**-------------------------------------------------------------------------------------------******************************************************************************* **************/uchar rd_lcd_data() //Read Display Data function{uchar temp_data;lcd_busy();RS=1;RW=1; //读用户数据条件P0=0xff; //51端口想输入时先拉高E=1;//_nop_();//_nop_(); //指该操作有效,即当E=1时，液晶模块数据的数据读到总线上。

19264液晶完整驱动程序 带字库st7920芯片驱动

void SendByteTo19264(u8 nbit,u8 bit);
void SendStringTo19264(u8 bit,u8 select,u8 data);
void Init_19264();
void screen_chear();
void display_chinese(u8 hang,u8 lie,u8 *array);
_delay_ms(3);
}
//------------------清屏JM12864---------------------
void screen_chear()
{
SendStringTo19264(upscreen,0,0x01);
SendStringTo19264(downscreen,0,0x01);
SendStringTo19264(upscreen,0,0x30); //使能基本指令 8位数据格式（在XY12864中）
//001DL X RE XX
/* DL=1,8位MPU接口；DL=0,4位MPU接口
RE＝1，扩充指令集；RE＝0，基本指令集
同一指令的动作不能同时改变DL和RE，需先改变DL再改变RE才能确保设置正确*/
SendStringTo19264(downscreen,0,0x30);
#define pin_19264data PINB&(1<<hf19264_data)
//--------------------------------------------------------
#define upscreen 1
#define downscreen 0

51单片机实现的多图显示用12864液晶驱动程序设计

51单片机实现的多图显示用12864液晶驱动程序设计作者：佚名日期：2010年06月02日来源：不详【字体：大中小】我要评论(0)核心提示：/************************************************程序名称：12864液晶驱动程序（显示多图）简要说明：控制器：KS0107 LCD型号：FM12864、TS12864A-2或兼容型号（不带字库）&nbs/************************************************程序名称：12864液晶驱动程序（显示多图）简要说明：控制器：KS0107LCD型号：FM12864、TS12864A-2或兼容型号（不带字库）MCU：AT89S5*，晶体频率：11.0592MHz取模方式：纵向取模、字节倒序CS1和CS2为高电平有效************************************************/;***************硬件端口定义***********RS EQU P2.0RW EQU P2.1E EQU P2.2CS1 EQU P2.3CS2 EQU P2.4RST EQU P2.5COM EQU 20H ;指令数据寄存器DAT EQU 21H ;显示数据寄存器;**********************************主程序入口地址ORG 0000HAJMP STRORG 0003H;*********************************中断程序入口地址STR:AJMP L0100L0100: CLR RSTNOPNOPSETB RST;********************************以上是软件复位MOV SP,#60HMOV IE,#81H ;中断允许MOV IP,#01H ;优先中断MOV TCON,#00H ;电平中断MOV COM,#3FH ;显示开LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;----------------------------------------------------------------------MOV COM,#0C0H ;第一行LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;----------------------------------------------------------------------MOV COM,#0B8H ;第一页LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;----------------------------------------------------------------------MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;********************************************************以上是软件初始化MOV B,#0AAHLCALL XIHX ;显示横线1LCALL DELAY; MOV B,#55H; LCALL XIHX; LCALL DELAY ;显示横线2MOV B,#0FFHMOV 29H,#00HLCALL XISXLCALL DELAY ;显示竖线1; MOV B,#00H; MOV 29H,#0FFH; LCALL XISX; LCALL DELAY ;显示竖线2MOV DPTR,#TAB1LCALL LEFTMOV DPTR,#TAB2LCALL RIGHTLCALL DELAY ;显示第一幅图片MOV DPTR,#TAB3LCALL LEFTMOV DPTR,#TAB4LCALL RIGHTLCALL DELAY ;显示第二幅图片MOV DPTR,#TAB5LCALL LEFTMOV DPTR,#TAB6LCALL RIGHTLCALL DELAY ;显示第三幅图片AJMP L0100;=======================================================以上是主程序LEFT: MOV R1,#0B8H_AB: MOV COM,R1 ;第一页LCALL S02A9 ;左半屏写指令子程序MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序MOV R0, #64S027B: MOV A,#00HMOVC A,@A+DPTRMOV DAT,ALCALL S02B1 ;左半屏写数据子程序INC DPTRDJNZ R0,S027BINC R1CJNE R1, #0C0H,_ABRET;======================================================以上是左半屏写数据子程序RIGHT: MOV R1,#0B8HABC: MOV COM,R1 ;第一页LCALL S02C1 ;右半屏写指令子程序MOV COM,#40H ;第一列LCALL S02C1 ;右半屏写指令子程序MOV R0, #64S027D: MOV A,#00HMOVC A,@A+DPTRMOV DAT,ALCALL S02B9 ;右半屏写数据子程序INC DPTRDJNZ R0,S027DINC R1CJNE R1, #0C0H,ABCRET;*******************************************************以上是右半屏写数据子程序XIHX: MOV R1,#0B8HBA: MOV COM,R1 ;第一页LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV R0, #64W027B: MOV DAT,BLCALL S02B1 ;左半屏写数据子程序LCALL S02B9 ;右半屏写数据子程序DJNZ R0,W027BINC R1CJNE R1, #0C0H,BARET;---------------------------------------------------------XISX: MOV R1,#0B8HCA: MOV COM,R1 ;第一页LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV R0, #32X027B: MOV DAT,BLCALL S02B1 ;左半屏写数据子程序LCALL S02B9 ;右半屏写数据子程序MOV DAT,29HLCALL S02B1 ;左半屏写数据子程序LCALL S02B9 ;右半屏写数据子程序DJNZ R0,X027BINC R1CJNE R1, #0C0H,CARET;****************************************************以上是显示线条程序S02A9: SETB CS1LCALL S02C9CLR CS1 ;左半屏写指令子程序RETS02B1: SETB CS1 ;左半屏写数据子程序LCALL S02E0CLR CS1RETS02C1: SETB CS2 ;右半屏写指令子程序LCALL S02C9CLR CS2RETS02B9: SETB CS2 ;右半屏写数据子程序LCALL S02E0CLR CS2RET;****************************************************S02C9: CLR RSSETB RWS02C9A: MOV P0,#0FFHSETB EMOV A, P0CLR EJB ACC.7,S02C9ACLR RWMOV P0,COMSETB ENOPCLR ERET;*************************************************以上是写指令子程序S02E0: CLR RSSETB RWS02E0A: MOV P0,#0FFHSETB EMOV A, P0CLR EJB ACC.7,S02E0ASETB RSCLR RWMOV P0,DATSETB ENOPCLR ERET;************************************************以上是写数据子程序DELAY: MOV R5,#0BH ;延时D1: MOV R7,#0FFHD2: MOV R6,#0FFHD3: DJNZ R6,$DJNZ R7,D2DJNZ R5,D1RET;****************************************************************TAB1:;-- 调入了一幅图像：C\128x64-1.bmp --;-- 宽度x高度=64x64 --DB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,080H,080H,0C0H,0C0 HDB0E0H,0E0H,0E0H,0F0H,0F0H,0F0H,0F0H,0F0H,0F8H,0F8H,0F8H,0F8H,0F8H,0F8H,0F8H,0F 8HDB0FCH,0FCH,0FCH,0FCH,0FCH,0FCH,0FCH,0FCH,0FCH,0FCH,07CH,078H,078H,038H,038H ,030HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,0E0H,0F0H,0FCH,0FEH,0FFH,0FFH,0FFH,0FFH,0F FHDB0FFH,0FFH,0FFH,0FFH,0EFH,0CFH,0E7H,0E7H,0E7H,0F3H,073H,033H,03BH,019H,00DH,0 8DHDB0CDH,0E7H,0F6H,0FEH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,07FH,03EH,01CH, 000HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,0E0H,0E0H,0F0H,0F0H,0F0H,0F8H,0F9H,0FDH,0FDH,0FDH,0DFH,09FH,08EH,08FH,0 8FHDB08FH,00FH,00FH,00FH,00FH,00FH,007H,003H,001H,060H,060H,06CH,06CH,06EH,06FH,06 7HDB067H,0E7H,0F7H,0F7H,0F3H,0F3H,0F3H,0F3H,0F9H,0F9H,0F8H,0F8H,0FCH,0FCH,0FEH,0 FEHDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,001H,00FH,07FH,0FFH,0FFH,0FFH,0FFH,0FFH,07FH,01FH,00FH,007H,003H,003H,00 1HDB081H,0E0H,0F0H,0F8H,0FCH,0FEH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FEH,0FEH,0FEH, 0FEHDB0FEH,0FCH,0FCH,0FCH,0F8H,0F0H,061H,001H,001H,003H,003H,007H,0DFH,0FFH,0FFH,0 FFHDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,001H,00FH,07FH,0FFH,0FFH,0E0H,0C0H,0C0H,080H,000H,000H,00 0HDB003H,007H,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00FH,00 7HDB087H,087H,0C3H,0C3H,0C1H,0E0H,0F0H,0F0H,0F8H,0FCH,0FCH,0FFH,0FFH,0FFH,0FFH, 0FFHDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,001H,00FH,07FH,0FFH,0FFH,0FFH,0FFH,0FFH,0F FHDB0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FEH,0FFH,0FFH,0FFH ,0FFHDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,07FH,07FH,03FH,03FH,03FH,01FH,01FH,01FH,0 0FHDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,003H,00FH,07FH,0FFH,0FFH,0FF HDB0FFH,07FH,07FH,03FH,03FH,03FH,01FH,01FH,01FH,00FH,00FH,00FH,007H,007H,003H,00 3HDB003H,001H,001H,001H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HTAB2:;-- 调入了一幅图像：C:\128x64-2.bmp --;-- 宽度x高度=64x64 --DB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,080H,080H,080H,0C0 HDB0C0H,0C0H,0E0H,0E0H,0E0H,0F0H,0F0H,0F8H,0F8H,0F8H,0FCH,0FCH,0FCH,0FEH,0FEH, 0FFHDB0FFH,0FFH,0FFH,0FEH,0F8H,0C0H,000H,000H,000H,000H,000H,000H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB030H,038H,078H,0F8H,0FCH,0FCH,0FCH,0FEH,0FEH,0FEH,0FFH,0FFH,0FFH,0FFH,0FFH, 0FFHDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH, 0FFHDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FEH,0F0H,0C0H,000H,000H,000H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,080H,0C0H,0F1H,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0 FFHDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH, 0FFHDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FEH,0F0H,080H,000H,000H,000H,0 00HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,03FH,007H,001H,001H,001H,001H,00 1HDB0E1H,0FDH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,01FH,007H,001H,001H,001H,0C1H,0 C1HDB001H,001H,001H,007H,01FH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FEH,0F0H,080H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,03FH,007H,001H,000H,000H,000H,000H,0E0H,0F8H,0F FHDB0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,03FH,007H,000H,000H,000H,000H,038H,03EH,03FH,0B FHDB0BFH,0F8H,0C0H,0C0H,0E0H,0E0H,0E7H,0FFH,0FFH,09FH,01FH,00FH,00FH,007H,007H,0 00HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB0FFH,0FFH,0FFH,0FFH,0EFH,0E1H,0E0H,0E0H,0E0H,0E0H,0E0H,0F8H,07FH,07FH,07FH,0 3FHDB03FH,03FH,07FH,07FH,07FH,078H,07CH,07CH,07CH,07EH,00EH,007H,003H,003H,003H,00 3HDB003H,003H,003H,00FH,03FH,07FH,07FH,07FH,07FH,07FH,07CH,070H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB00FH,00FH,007H,007H,003H,003H,003H,001H,001H,001H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HTAB3:;-- 调入趣味性文字和图片像右半屏：纵向取模下高位,数据排列:从左到右从上;-- 宽度x高度=64x64 --DB000H,000H,000H,000H,000H,000H,000H,000H,000H,0E0H,0C0H,080H,0C0H,0F8H,0F0H,0B 0HDB060H,068H,0D0H,0F0H,0F0H,020H,020H,060H,0C0H,0C0H,0C0H,0C0H,080H,080H,080H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,0C0H,0F0H,0FCH,0EFH,0F3H,0F9H,0FCH,0F1H,07BH,07DH,0 3FHDB03EH,038H,03EH,03CH,03DH,038H,03FH,03FH,03EH,03EH,03FH,03FH,03FH,03FH,07FH,0 7FHDB0FFH,0FEH,0FEH,0FCH,0F8H,0F0H,0E0H,080H,000H,000H,000H,000H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,0E0H,0FEH,0FFH,0FFH,0FFH,07FH,007H,001H,000H,000H,008H,008H,00 8HDB010H,010H,020H,040H,000H,000H,000H,000H,000H,040H,020H,010H,010H,008H,008H,008 HDB000H,000H,001H,007H,03FH,0FFH,0FFH,0FFH,0FEH,0E0H,000H,000H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,080H,09FH,0FFH,0FFH,063H,061H,0E0H,0E0H,0F0H,0F0H,0F0H,0F0H,0D0H,08 0HDB010H,010H,020H,020H,0C0H,060H,060H,060H,0C0H,0E0H,0E0H,0F0H,0F0H,0F0H,0F0H,0D 0HDB010H,010H,010H,020H,0E0H,060H,061H,0FFH,0FFH,09FH,080H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB006H,009H,010H,010H,020H,039H,060H,080H,001H,003H,007H,007H,007H,007H,007H,007 HDB007H,004H,004H,022H,041H,040H,040H,040H,041H,023H,007H,007H,007H,007H,007H,007 HDB007H,004H,004H,002H,001H,080H,060H,039H,020H,010H,010H,019H,0E6H,000H,004H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,080H,0C0H,0C0H,0E1H,0E2H,0E2H,0F4H,0F4H,0F4H,0F8H,0F 8HDB0F8H,0F0H,0F0H,0F0H,090H,090H,090H,090H,090H,070H,0F0H,0F0H,0E8H,0E8H,0E8H,0C 4HDB0C4H,084H,082H,002H,0FBH,0F4H,0E4H,0F4H,0FCH,004H,002H,001H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,007H,00FH,01FH,03FH,03FH,07FH,07FH,0FFH,021H,001H,003H,007 HDB00FH,09FH,0FFH,0FFH,0FFH,0FEH,0F9H,0F7H,0FEH,0F8H,0FFH,0FFH,0FFH,0FFH,0FFH,0 E7HDB00FH,00FH,01FH,01FH,03FH,03FH,03FH,03FH,01FH,000H,000H,000H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,001H,002H,004H,004H,004 HDB002H,001H,00FH,03FH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0 FFHDB0FFH,0FCH,0F0H,060H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HTAB4:;-- 调入了一幅图像：帅呆了吧DB000H,000H,0E0H,000H,0F8H,000H,0E0H,020H,0F8H,020H,020H,0E0H,000H,000H,000H,078 HDB048H,048H,0C8H,048H,048H,078H,000H,000H,000H,000H,008H,008H,008H,008H,0C8H,048 HDB028H,018H,008H,000H,000H,0F0H,010H,0F0H,000H,0F0H,010H,010H,0F0H,010H,0F8H,010 HDB000H,000H,000H,000H,000H,000H,000H,000H,0E0H,0F0H,0F0H,0E0H,000H,000H,000H,000 HDB000H,020H,017H,008H,007H,000H,00FH,000H,03FH,000H,008H,00FH,000H,021H,011H,009 HDB005H,003H,03FH,003H,005H,009H,011H,011H,000H,000H,000H,000H,020H,020H,03FH,000 HDB000H,000H,000H,000H,000H,007H,004H,007H,000H,01FH,021H,021H,021H,021H,021H,038 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,01BH,01BH,000H,000H,000H,000H,000 HDB000H,0F4H,05CH,034H,05CH,0F4H,000H,05CH,048H,07EH,048H,048H,000H,040H,05EH,0D 4HDB054H,054H,040H,0DEH,054H,054H,052H,058H,000H,000H,002H,002H,002H,002H,0F2H,012DB00AH,006H,002H,000H,000H,0FCH,084H,084H,0FCH,000H,03AH,022H,0A2H,0FEH,022H,02 2HDB000H,000H,000H,000H,000H,000H,000H,000H,038H,0FCH,0FCH,038H,000H,000H,000H,000 HDB000H,00FH,005H,005H,005H,00FH,000H,00FH,009H,009H,009H,00FH,000H,00AH,009H,00B HDB005H,003H,000H,00FH,00AH,009H,009H,00EH,000H,000H,000H,000H,008H,008H,00FH,000 HDB000H,000H,000H,000H,000H,001H,000H,008H,009H,004H,002H,009H,008H,00FH,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,006H,006H,000H,000H,000H,000H,000 HDB000H,018H,0FFH,008H,050H,044H,044H,0FFH,044H,044H,07CH,040H,000H,020H,022H,02 AHDB0B2H,062H,0FFH,062H,0B2H,02AH,022H,020H,000H,004H,004H,0FFH,004H,004H,0FCH,00 0HDB0FCH,004H,004H,0FCH,000H,000H,000H,000H,0C1H,031H,00EH,030H,0C0H,000H,000H,00 0HDB000H,000H,000H,07CH,055H,056H,0FCH,056H,055H,054H,07CH,000H,000H,000H,000H,00 0HDB000H,000H,007H,0C4H,004H,002H,001H,0C0H,001H,002H,004H,004H,000H,002H,002H,0C 1HDB000H,000H,087H,080H,080H,0C1H,082H,002H,000H,004H,003H,080H,044H,004H,003H,000 HDB0C7H,002H,002H,007H,000H,004H,082H,001H,000H,0C0H,000H,000H,000H,0C1H,002H,00 4HDB000H,001H,001H,0C1H,041H,041H,0C7H,041H,041H,041H,0C1H,001H,000H,000H,000H,00DB000H,000H,080H,07FH,012H,012H,012H,013H,0F2H,002H,002H,002H,000H,061H,019H,0FF HDB009H,091H,07FH,000H,000H,0FFH,000H,0C0H,000H,0FFH,091H,091H,091H,0FFH,004H,00 BHDB031H,001H,001H,0FFH,000H,002H,0FFH,002H,002H,07FH,022H,022H,022H,07FH,002H,002 HDB000H,020H,020H,017H,08DH,075H,007H,005H,0FDH,015H,027H,020H,000H,000H,000H,000 HDB000H,001H,000H,000H,000H,000H,000H,000H,001H,000H,000H,000H,000H,000H,000H,001 HDB001H,000H,000H,000H,000H,001H,001H,001H,000H,001H,000H,000H,000H,001H,000H,000 HDB001H,001H,001H,000H,000H,000H,001H,001H,001H,001H,001H,001H,001H,001H,001H,001 HDB000H,000H,001H,001H,000H,000H,000H,000H,001H,000H,000H,000H,000H,000H,000H,000 HTAB5:;-- 调入图像：纵向取模下高位,数据排列:从左到右从上到下;-- 宽度x高度=64x64 --DB000H,000H,000H,000H,000H,000H,000H,000H,000H,0C0H,0E0H,0E0H,0F0H,0F0H,0F0H,0F 0HDB0F0H,0F0H,0F8H,0BCH,01CH,08CH,0CEH,0CFH,0CFH,0EBH,0C9H,0D0H,090H,010H,010H, 010HDB020H,021H,061H,041H,043H,0C2H,08CH,000H,001H,001H,002H,006H,00CH,00FH,010H,03 EHDB023H,046H,085H,089H,019H,033H,066H,08DH,0DBH,0F9H,0A6H,02FH,03FH,007H,08FH,0C FHDB000H,000H,000H,080H,0E0H,0F0H,0F0H,0F0H,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0 FFHDB0FFH,07FH,0FFH,0EFH,0FFH,0FFH,0FFH,0FFH,07FH,06FH,037H,01BH,00FH,007H,001H,0 0FHDB009H,00AH,00EH,006H,006H,004H,004H,00CH,008H,018H,010H,020H,060H,040H,0C0H,08 0HDB000H,000H,000H,001H,0C3H,007H,00DH,037H,022H,0C2H,083H,001H,00FH,037H,01FH,03 7HDB000H,000H,000H,0FFH,0FFH,0FFH,0FFH,01FH,006H,0C6H,0E6H,066H,07EH,0FFH,0EFH,0 D1HDB0D9H,0E9H,0E9H,0F9H,0F2H,0E6H,01CH,030H,000H,000H,000H,000H,000H,000H,000H,00 0HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,001 HDB003H,0C6H,078H,0B0H,0E0H,083H,00EH,018H,0E0H,080H,003H,00EH,038H,0C0H,018H,0F 0HDB000H,000H,000H,000H,007H,00FH,01FH,01FH,01CH,0FFH,07FH,060H,038H,027H,079H,0C 1HDB0F3H,0F3H,0FFH,0FFH,078H,03FH,002H,000H,000H,000H,000H,000H,000H,000H,002H,071 HDB039H,019H,0F9H,0F9H,0F9H,0FBH,0FBH,073H,073H,0E6H,0CEH,09CH,038H,030H,000H,0 00HDB000H,01FH,0E0H,0FFH,0FFH,0FFH,0FCH,0F8H,0E0H,087H,0F8H,000H,000H,007H,0FEH,0 F1HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,07FH,0C0H,000H,000H,000H,000H,000 HDB080H,000H,000H,010H,010H,000H,020H,020H,020H,000H,000H,000H,000H,000H,01CH,03E HDB070H,07CH,07CH,078H,0FFH,0FFH,07FH,07EH,03EH,01FH,003H,003H,002H,000H,000H,00 0HDB000H,000H,000H,0FBH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,000H,000H,000H,0FFH,0 F3HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,003H,018H,0E0H,000H,000H,000 HDB003H,006H,00EH,00EH,00EH,018H,018H,018H,008H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,080 HDB0C0H,0C6H,0EFH,0A7H,073H,07BH,009H,084H,0CCH,0E3H,0FFH,0F8H,0FCH,0FEH,0FFH, 0FFHDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,002H,006 HDB000H,00CH,008H,008H,000H,010H,010H,010H,010H,010H,018H,018H,008H,084H,084H,004 HDB006H,0F2H,0B2H,016H,034H,0E4H,004H,004H,004H,00CH,0CCH,08CH,01CH,018H,03FH,0 3FHDB07CH,0DEH,0DFH,0DFH,0EEH,0F7H,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH, 0FFHDB000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000H,000 HDB000H,000H,000H,000H,000H,000H,000H,004H,004H,00EH,036H,064H,07CH,018H,001H,003 HDB00EH,000H,001H,001H,003H,001H,000H,000H,000H,000H,003H,003H,003H,001H,000H,000 HDB000H,000H,001H,007H,00FH,03FH,07FH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0 FFHTAB6:;-- 调入图像：纵向取模下高位,数据排列:从左到右从上到下;-- 宽度x高度=64x64;-- 调入了一幅图像：我们年轻.bmp --;-- 宽度x高度=64x64 --DB000h,000h,000h,000h,000h,000h,000h,000h,080h,080h,000h,0C0h,000h,080h,000h,000h DB000h,000h,000h,000h,000h,0C0h,000h,040h,080h,000h,080h,080h,080h,000h,000h,000h DB000h,000h,0C0h,000h,000h,000h,000h,000h,000h,000h,080h,000h,000h,000h,000h,000h DB0C0h,000h,000h,000h,080h,080h,080h,080h,080h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,044h,044h,045h,025h,0FFh,014h,014h,084h,07Fh,0C4h,024h,015h,084h DB000h,000h,008h,004h,0FFh,000h,0FFh,000h,000h,000h,000h,000h,0FFh,000h,000h,000h DB044h,042h,079h,049h,049h,049h,0FFh,049h,049h,049h,049h,041h,000h,000h,089h,08Fh DB049h,0FDh,029h,001h,028h,024h,0E2h,023h,024h,008h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,080h,080h,088h,0B2h,003h,020h,0A1h,028h,030h,020h,0E1h,022h,023h DB000h,000h,080h,040h,03Bh,020h,023h,020h,0E0h,020h,020h,022h,033h,020h,000h,000h DB020h,0E0h,038h,0A0h,020h,020h,013h,090h,050h,070h,090h,000h,000h,000h,020h,0A0h DB0A8h,0B3h,0A0h,0A2h,082h,0FAh,083h,092h,0A2h,082h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,040h,020h,01Fh,020h,050h,048h,045h,042h,045h,048h,050h,040h DB000h,000h,008h,008h,00Fh,009h,009h,009h,07Fh,009h,009h,009h,009h,008h,000h,000h DB011h,011h,009h,07Fh,005h,040h,045h,044h,07Ch,044h,044h,041h,000h,000h,020h,01Bh DB042h,07Eh,00Ah,053h,020h,01Fh,000h,07Fh,040h,070h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,040h,040h,040h,05Fh,055h,055h,0D5h,055h,05Fh,040h,040h,040h DB000h,000h,010h,011h,0F6h,000h,000h,0FCh,056h,055h,054h,05Eh,0C4h,000h,000h,000h DB010h,0D4h,014h,0FFh,094h,094h,022h,022h,0FEh,022h,022h,020h,000h,000h,008h,008hDB008h,008h,0C8h,03Fh,048h,088h,008h,008h,00Ch,008h,000h,000h,000h,000h,000h,000hDB000h,000h,000h,000h,000h,0C8h,044h,043h,0C4h,008h,0CFh,049h,049h,049h,0E9h,048h DB000h,000h,008h,084h,0C3h,0A4h,088h,00Bh,00Ah,0EAh,08Ah,08Ah,08Bh,008h,000h,000h DB08Ch,003h,004h,0E7h,008h,008h,008h,0E8h,00Bh,008h,008h,008h,000h,000h,048h,044hDB042h,041h,040h,041h,046h,040h,041h,042h,06Ch,044h,000h,000h,000h,000h,000h,000hDB000h,000h,000h,000h,000h,0FFh,022h,025h,018h,000h,0FFh,044h,044h,044h,0FFh,000hDB000h,000h,000h,0FFh,088h,088h,0FFh,002h,005h,018h,080h,000h,0FFh,000h,000h,000hDB020h,013h,008h,0FFh,002h,002h,002h,0FFh,002h,002h,002h,002h,000h,000h,000h,0FFhDB009h,011h,0FFh,000h,000h,0FFh,009h,011h,0FFh,000h,000h,000h,000h,000h,000h,000hDB 000h,000h,000h,000h,000h,001h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB 000h,000h,000h,001h,000h,000h,001h,000h,000h,000h,000h,001h,000h,000h,000h,000h DB 000h,000h,000h,001h,000h,001h,001h,001h,001h,001h,001h,000h,000h,000h,000h,001h DB 000h,001h,001h,000h,000h,001h,000h,001h,001h,000h,000h,000h,000h,000h,000h,000h END上传两个显示画面液晶屏是朋友托卖的，无背光无字库，带负压产生电路，有些成色比较新，先到先得了，45RMB一块，送资料，驱动程序，QQ以下是程序//**************************************;* 控制器：KS0107 *;* LCD型号：TS12864A-2或兼容型号 *;* MCU:AT89S5* ,晶体频率：11.0592MHz *;* 取模方式：纵向字节倒序 *;* CS1和CS2为高电平有效 * *;***************硬件端口定义***********RS EQU P2.4RW EQU P2.3E EQU P2.2CS1 EQU P2.7CS2 EQU P2.6RST EQU P2.5BUF EQU P0;******************************************COM EQU 20H ;指令数据寄存器DAT EQU 21H ;显示数据寄存器;**********************************主程序入口地址ORG 0000HAJMP STRORG 0003H;*********************************中断程序入口地址STR:AJMP L0100L0100: CLR RSTNOPNOPSETB RST;********************************以上是软件复位MOV SP,#60HMOV IE,#81H ;中断允许MOV IP,#01H ;优先中断MOV TCON,#00H ;电平中断MOV COM,#3FH ;显示开LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;---------------------------------------------------------------------- MOV COM,#0C0H ;第一行LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;---------------------------------------------------------------------- MOV COM,#0B8H ;第一页LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;---------------------------------------------------------------------- MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序;********************************************************以上是软件初始化MOV B,#0AAHLCALL XIHX ;显示横线1LCALL DELAYMOV B,#55HLCALL XIHXLCALL DELAY ;显示横线2MOV B,#0FFHMOV 29H,#00HLCALL XISXLCALL DELAY ;显示竖线1MOV B,#00HMOV 29H,#0FFHLCALL XISXLCALL DELAY ;显示竖线2MOV DPTR,#TAB1LCALL LEFTMOV DPTR,#TAB2LCALL RIGHTLCALL DELAY ;显示第一幅图片MOV DPTR,#TAB3LCALL LEFTMOV DPTR,#TAB4LCALL RIGHTLCALL DELAY ;显示第二幅图片MOV DPTR,#TAB5LCALL LEFTMOV DPTR,#TAB6LCALL RIGHTLCALL DELAY ;显示第三幅图片AJMP L0100;=======================================================以上是主程序LEFT: MOV R1,#0B8H_AB: MOV COM,R1 ;第一页LCALL S02A9 ;左半屏写指令子程序MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序MOV R0, #64S027B: MOV A,#00HMOVC A,@A+DPTRMOV DAT,ALCALL S02B1 ;左半屏写数据子程序INC DPTRDJNZ R0,S027BINC R1CJNE R1, #0C0H,_ABRET;======================================================以上是左半屏写数据子程序RIGHT: MOV R1,#0B8HABC: MOV COM,R1 ;第一页LCALL S02C1 ;右半屏写指令子程序MOV COM,#40H ;第一列LCALL S02C1 ;右半屏写指令子程序MOV R0, #64S027D: MOV A,#00HMOVC A,@A+DPTRMOV DAT,ALCALL S02B9 ;右半屏写数据子程序INC DPTRDJNZ R0,S027DINC R1CJNE R1, #0C0H,ABCRET;*******************************************************以上是右半屏写数据子程序XIHX: MOV R1,#0B8HBA: MOV COM,R1 ;第一页LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV R0, #64W027B: MOV DAT,BLCALL S02B1 ;左半屏写数据子程序LCALL S02B9 ;右半屏写数据子程序DJNZ R0,W027BINC R1CJNE R1, #0C0H,BARET;--------------------------------------------------------- XISX: MOV R1,#0B8HCA: MOV COM,R1 ;第一页LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV COM,#40H ;第一列LCALL S02A9 ;左半屏写指令子程序LCALL S02C1 ;右半屏写指令子程序MOV R0, #32X027B: MOV DAT,BLCALL S02B1 ;左半屏写数据子程序LCALL S02B9 ;右半屏写数据子程序MOV DAT,29HLCALL S02B1 ;左半屏写数据子程序LCALL S02B9 ;右半屏写数据子程序DJNZ R0,X027BINC R1CJNE R1, #0C0H,CARET;****************************************************以上是显示线条程序S02A9: SETB CS1LCALL S02C9CLR CS1 ;左半屏写指令子程序RETS02B1: SETB CS1 ;左半屏写数据子程序LCALL S02E0CLR CS1RETS02C1: SETB CS2 ;右半屏写指令子程序LCALL S02C9CLR CS2RETS02B9: SETB CS2 ;右半屏写数据子程序LCALL S02E0CLR CS2RET;****************************************************S02C9: CLR RSSETB RWS02C9A: MOV BUF,#0FFHSETB EMOV A, BUFCLR EJB ACC.7,S02C9ACLR RWMOV BUF,COMSETB ENOPCLR ERET;*************************************************以上是写指令子程序S02E0: CLR RSSETB RWS02E0A: MOV BUF,#0FFHSETB EMOV A, BUFCLR EJB ACC.7,S02E0ASETB RSCLR RWMOV BUF,DATSETB ENOPCLR ERET;************************************************以上是写数据子程序DELAY: MOV R5,#0BH ;延时D1: MOV R7,#0FFHD2: MOV R6,#0FFHD3: DJNZ R6,$DJNZ R7,D2DJNZ R5,D1RET;****************************************************************TAB1:;-- 调入菲戈幅图像左半屏：纵向取模下高位,数据排列:从左到右从上到下;-- 宽度x高度=64x64DB000h,000h,000h,040h,080h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,010h DB060h,080h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,0FCh,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,0C0h,030h,008h,000h,000h,000h,000h DB000h,000h,000h,000h,000h,080h,040h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,000h,001h,002h,004h,008h,010h,020h,040h,080h,000h,000h,000h DB000h,001h,006h,018h,060h,080h,000h,000h,000h,000h,000h,000h,000h,0FFh,000h,000h DB000h,000h,000h,000h,000h,0C0h,030h,00Ch,003h,000h,000h,000h,000h,080h,040h,020h DB010h,008h,004h,002h,001h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB002h,002h,004h,004h,008h,008h,010h,010h,020h,020h,040h,040h,080h,081h,002h,004h DB008h,010h,020h,040h,080h,001h,006h,018h,020h,000h,000h,000h,080h,09Fh,080h,000h DB000h,040h,030h,00Ch,003h,080h,040h,020h,010h,008h,004h,002h,001h,000h,000h,080h DB080h,040h,040h,020h,020h,010h,010h,010h,008h,008h,004h,004h,002h,002h,000h,000h000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,001h,001h DB002h,002h,004h,004h,008h,009h,000h,030h,0CCh,002h,001h,001h,000h,000h,000h,001h DB001h,002h,0CCh,030h,001h,000h,008h,008h,004h,004h,002h,002h,001h,001h,001h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,004h,018h DB060h,080h,000h,000h,000h,000h,000h,000h,000h,001h,002h,002h,084h,0FCh,044h,042h DB022h,021h,020h,020h,010h,010h,010h,060h,080h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,003h,004h,004h,002h,002h,002h,001h,001h,001h,001h,000h,0FFh,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,001h,006h,008h,010h,000h,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h,000h DB000h,000h,080h,080h,040h,040h,020h,020h,010h,010h,008h,008h,004h,00Fh,010h,020h。

128x64液晶KS0108控制器驱动程序

#include "absacc.h"#include "intrins.h"//自定义库在"C:\comp51\UserLib\"文件夹中#include ".\inc\ASCII816.h" //标准ASCII库#include ".\inc\HZTable.h" //汉字点阵库(自做)#include ".\inc\Menu.h" //菜单库(自做)// LCD128*64 数据线#define LCD12864DataPort P1// LCD128*64 I/O 信号管脚sbit di =P3^1; // 数据\指令选择sbit rw =P3^3; // 读\写选择sbit en =P3^2; // 读\写使能sbit cs1 =P3^4; // 片选1,低有效(前64列)sbit cs2 =P3^5; // 片选2,低有效(后64列)sbit reset=P0^7; // 复位/*----------------------------------------------------------------------------------------------------*/ /* ****函数列表****//开关显示void SetOnOff(unsigned char onoff)//选择屏幕//screen: 0-全屏,1-左屏,2-右void SelectScreen(unsigned char screen)//清屏//screen: 0-全屏,1-左屏,2-右void ClearScreen(unsigned char screen)//显示8*8点阵//旋转90度:字模被竖着切分//lin:行(0-7), column: 列(0-15)//address : 字模区首地址void Show88(unsigned char lin,unsigned char column,unsigned int address)//显示8*16字符//旋转90度:字模被竖着切分//lin:行(0-3), column: 列(0-15)//character:字符代码(标准ASCII码)void ShowChar(unsigned char lin,unsigned char column,unsigned char character)//显示8*16字符串//!!!只能显示在一行上即: 串长+column <=15//旋转90度:字模被竖着切分//lin:行(0-3), column: 列(0-15)//address : 字模区首地址void ShowString(unsigned char lin,unsigned char column, unsigned char *string)//显示一个汉字//旋转90度:字模被竖着切分//lin:行(0-3), column: 列(0-15)//hzcode: 汉字代码(自定义的)void ShowHZ(unsigned char lin,unsigned char column,unsigned int hzcode)//显示图片//旋转90度:字模被竖着切分//startline :开始行//startcolumn:开始列//linechar :图片行点除8(图片以8*8点阵为单位)//columnchar :图片列点除8(图片以8*8点阵为单位)//address : 字模区首地址void ShowPicture(unsigned char startline,unsigned char startcolumn,unsigned char linechar,unsigned char columnchar,unsigned int address)//!!问题大户//显示一行汉字//lin:行//lineheadaddr: 此行汉字代码区首地址void ShowLine(unsigned char lin,unsigned int lineheadaddr)//显示一屏汉字//pageheadaddr:此屏汉字代码地址区首地址void ShowPage(unsigned int pageheadaddr)//反显一个8*8字块//lin:行(0-3), column: 列(0-7)void ReverseShow88(unsigned char lin,unsigned char column)//反显一个字符//lin:行(0-4), column: 列(0-15)void ReverseShowChar(unsigned char lin,unsigned char column)//反显一个汉字//lin:行(0-3), column: 列(0-7)ReverseShowHZ(unsigned char lin,unsigned char column)//反显一行汉字//lin:行ReverseShow(unsigned char lin)//初始化LCDvoid InitLCD()****函数列表结束**** *//*----------------------------------------------------------------------------------------------------*//*--基本函数源程序------------------------------------------------------------------------------------*/ //延时Lcd12864delay(){unsigned int i=500;while(i--) {;}}/*----------------------------------------------------------------------------------------------------*///状态检查void CheckState(){unsigned char dat;di=0;rw=1;do{LCD12864DataPort=0xff;en=1; dat=LCD12864DataPort; en=0;dat=0x90 & dat; //仅当第4,7位为0时才可操作}while(!(dat==0x00));}/*----------------------------------------------------------------------------------------------------*///写显示数据//dat:显示数据void WriteByte(unsigned char dat){CheckState();di=1; rw=0;LCD12864DataPort=dat;en=1; en=0;}/*-----------------------------------------------------------------------------------------------------*/ //向LCD发送命令//command :命令SendCommandToLCD(unsigned char command){CheckState();rw=0;LCD12864DataPort=command;en=1; en=0;}/*----------------------------------------------------------------------------------------------------*/ //设定行地址(页)--X 0-7void SetLine(unsigned char line){line=line & 0x07; // 0<=line<=7line=line|0xb8; //1011 1xxxSendCommandToLCD(line);}//设定列地址--Y 0-63void SetColumn(unsigned char column){column=column &0x3f; // 0=<column<=63column=column | 0x40; //01xx xxxxSendCommandToLCD(column);}//设定显示开始行--XXvoid SetStartLine(unsigned char startline) //0--63{startline=startline & 0x07;startline=startline|0xc0; //1100 0000SendCommandToLCD(startline);}//开关显示void SetOnOff(unsigned char onoff){onoff=0x3e | onoff; //0011 111xSendCommandToLCD(onoff);}/*---------------------------------------------------------------------------------------------------*///选择屏幕//screen: 0-全屏,1-左屏,2-右屏void SelectScreen(unsigned char screen){ //北京显示器:负有效cs1: 0--右; cs2: 0--左switch(screen){ case 0: cs1=0;//全屏_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();cs2=0;_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();_nop_();break;case 1: cs1=1;//左屏_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();cs2=0;_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();break;case 2: cs1=0;//右屏_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();cs2=1;_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();break;}}/*---------------------------------------------------------------------------------------------------*///清屏//screen: 0-全屏,1-左屏,2-右void ClearScreen(unsigned char screen){ unsigned char i,j;SelectScreen(screen);for(i=0;i<8;i++){ SetLine(i);for(j=0;j<64;j++){WriteByte(0x00);}}}/*--------------------------------------------------------------------------------------------------*/ //显示8*8点阵//旋转90度:字模被竖着切分//lin:行(0-7), column: 列(0-15)//address : 字模区首地址void Show88(unsigned char lin,unsigned char column,unsigned int address) { unsigned char i;if(column>16) {return;}if(column<8) SelectScreen(1); //如果列数<8(0,1,2,3,4,5,6,7)则写在第一屏上else {SelectScreen(2); //否则(8,9,10,11,12,13,14,15)写在第二屏上column=column & 0x07; //防止越界}SetLine(lin);SetColumn(column<<3);for(i=0;i<8;i++) WriteByte( CBYTE[address+i] );}/*------------------------------------------------------------------------------------------------*///显示8*16字符//旋转90度:字模被竖着切分//lin:行(0-3), column: 列(0-15)//character:字符代码(标准ASCII码)void ShowChar(unsigned char lin,unsigned char column,unsigned char character) { lin=lin<<1;Show88(lin ,column,ASCII816[character-0x20] );Show88(lin+1,column,ASCII816[character-0x20]+8 );}/*-----------------------------------------------------------------------------------------------*//*//显示8*16字符串//!!!只能显示在一行上即: 串长+column <=15//旋转90度:字模被竖着切分//lin:行(0-3), column: 列(0-15)//address : 字模区首地址void ShowString(unsigned char lin,unsigned char column, unsigned char *string) { unsigned char ch;unsigned char i=0;while(*string!='\0'){ch=*string;if(i+column >15) break; //(只能显示在一行上即: 串长+column <=15) ShowChar(lin,i+column,ch);string++; i++;}}*//*----------------------------------------------------------------------------------------------*///显示一个汉字//旋转90度:字模被竖着切分//lin:行(0-3), column: 列(0-7)//hzcode: 汉字代码(自定义的)//uchar code HZtablevoid ShowHZ(unsigned char lin,unsigned char column,unsigned int hzcode){lin=lin<<1; //lin*2Show88(lin,column,HZTable[hzcode]);Show88(lin,column+1,HZTable[hzcode]+8);Show88(lin+1,column,HZTable[hzcode]+16);Show88(lin+1,column+1,HZTable[hzcode]+24);}/*----------------------------------------------------------------------------------------------*///显示图片//旋转90度:字模被竖着切分//startline :开始行//startcolumn:开始列//linechar :图片行点除8(图片以8*8点阵为单位)//columnchar :图片列点除8(图片以8*8点阵为单位)//address : 字模区首地址void ShowPicture(unsigned char startline,unsigned char startcolumn,unsigned char linechar,unsigned char columnchar,unsigned int address){ unsigned char i,j;for(i=0;i<columnchar;i++)for(j=0;j<linechar;j++)Show88(startline+i , startcolumn+j , address+(i*linechar+j)*8 );}/*----------------------------------------------------------------------------------------------*///显示一行字符串(汉字,字母混排,一行16字节)//lin:行//lineheadaddr: 此行汉字代码区首地址void ShowLine(unsigned char lin,unsigned char linehead[]) { unsigned char i;unsigned char byte;unsigned int hzcode;for( i=0; i<16; ){ byte=linehead[i];if(byte < 0x80) //字母{if(i>15) return; //!!编译器有问题,须强制退出ShowChar(lin, i , byte);i=i+1;}else // byte >= 0x80(汉字){if(i>15) return; //!!编译器有问题,须强制退出byte=byte & 0x7f; //最高位置0,即:减去0x8000 hzcode=(unsigned int)byte<<8; //?? //高8位hzcode=hzcode+linehead[i+1]; //加低8位,组合成整型数地址ShowHZ( lin,i,hzcode);i=i+2;}}}/*----------------------------------------------------------------------------------------------------*///显示一屏汉字//pageheadaddr:此屏汉字代码地址区首地址void ShowPage(unsigned char pagehead[][16]){ unsigned char i;for(i=0;i<4;i++) ShowLine(i,pagehead[i]); //1行8个汉字,16字节}/*----------------------------------------------------------------------------------------------------*///读显示数据unsigned char ReadByte(){unsigned char dat;CheckState();di=1; rw=1;LCD12864DataPort=0xff;en=1; dat=LCD12864DataPort; en=0;return(dat);}/*----------------------------------------------------------------------------------------------------*/ //反显一个8*8字块//lin:行(0-3), column: 列(0-7)void ReverseShow88(unsigned char lin,unsigned char column){ unsigned char i;unsigned char tab[8];if(column<8) SelectScreen(1); //如果列数<4(0,1,2,3),则写在第一屏上else SelectScreen(2); //否则(4,5,6,7), 写在第二屏上//读上部8列column=column<<3; //每个方块8*8大小SetLine(lin);SetColumn(column);tab[0]=ReadByte(); //空读!!!!! //?for(i=0;i<8;i++) tab[i]=~ReadByte();//写回SetLine(lin);SetColumn(column);for(i=0;i<8;i++) WriteByte(tab[i]);}/*----------------------------------------------------------------------------------------------------*/ /*----------------------------------------------------------------------------------------------------*/ //反显一个字符//lin:行(0-4), column: 列(0-15)void ReverseShowChar(unsigned char lin,unsigned char column){ lin=lin<<1;ReverseShow88(lin ,column);ReverseShow88(lin+1,column);}/*----------------------------------------------------------------------------------------------------*///反显一个汉字//lin:行(0-3), column: 列(0-7)ReverseShowHZ(unsigned char lin,unsigned char column){lin=lin<<1;column=column<<1;ReverseShow88(lin ,column );ReverseShow88(lin ,column+1);ReverseShow88(lin+1,column );ReverseShow88(lin+1,column+1);}/*----------------------------------------------------------------------------------------------------*/ //反显一行汉字//lin:行ReverseShow(unsigned char lin){ unsigned char i;for(i=0;i<8;i++) ReverseShowHZ(lin,i);}/*----------------------------------------------------------------------------------------------------*/ void InitLCD() //初始化LCD{ unsigned char i=250; //延时while(i--);//reset=0;//复位//reset=1;SelectScreen(0);SetOnOff(0); //关显示ClearScreen(1);//清屏ClearScreen(2);SelectScreen(0);SetOnOff(1); //开显示SelectScreen(0);SetStartLine(0); //开始行:0}/*----------------------------------------------------------------------------------------------------*/void Reset() //液晶复位{//reset 低复位_|-reset=0;_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();reset=1;//全屏cs1=0;_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();cs2=0;_nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_(); _nop_();_nop_(); SendCommandToLCD(0x3F);}</FONT< p>。

KS0108内核液晶驱动程序介绍

直接看指令表：由以上指令可以得到如下初始化液晶的程序：void vLCDInitialize(){CS1=1;CS2=1;vWriteCMD(0x38); //8位形式，两行字符。

vWriteCMD(0x0F); //开显示。

vWriteCMD(0x01); //清屏。

vWriteCMD(0x06); //画面不动，光标右移。

vWriteCMD(LCDSTARTROW); //设置起始行。

}全屏初始化，不忙？写命令，这里注意，控制显示的指令和ST7920相同，这里没有详细列出。

不同的是，起始行,列，和页分别定义如下：#define LCDSTARTROW 0xC0 //设置起始行指令。

#define LCDPAGE 0xB8 //设置页指令。

#define LCDLINE 0x40可以通过上面的指令表查表宏定义。

//在8×128的格子里显示自定义长度的一行void vShowCustomRow(unsigned char ucPage,unsigned char ucLine,unsigned char ucWidth,unsigned char *ucaRow){unsigned char ucCount;if(ucLine<64) {CS1=1;CS2=0;vWriteCMD(LCDPAGE+ucPage);vWriteCMD(LCDLINE+ucLine);if((ucLine+ucWidth)<64){for(ucCount=0;ucCount<ucWidth;ucCount++)vWriteData(*(ucaRow+ucCount));}else{for(ucCount=0;ucCount<64-ucLine;ucCount++)vWriteData(*(ucaRow+ucCount));CS1=0;CS2=1;vWriteCMD(LCDPAGE+ucPage);vWriteCMD(LCDLINE);for(ucCount=64-ucLine;ucCount<ucWidth;ucCount++)vWriteData(*(ucaRow+ucCount));}}else{CS1=0;CS2=1;vWriteCMD(LCDPAGE+ucPage);vWriteCMD(LCDLINE+ucLine-64);for(ucCount=0;ucCount<ucWidth;ucCount++)vWriteData(*(ucaRow+ucCount));}}1、void vShowCustomRow(unsigned char ucPage,unsigned char ucLine,unsigned char ucWidth,unsigned char *ucaRow)：四个参数：从那一页开始写，从哪一列开始写，写入多宽数据，写入的数据存放在哪里。

  1. 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

KS0107 KS0108控制的19264液晶驱动程序C51示例2007年01月29日星期一 11:57// 19264 Demo Program//***************************************************************************//连线表: CPU=89C52*//RS=P3.0 R/W=P3.1 E=P3.2 CS1=P3.3 CS2=P3.4 CS3=P3.5 *//SysClock=12MHz DB0-DB7=P1.0-P1.7 /Reset=InBoar d *//***************************************************************************#include <reg52.h>#include <stdlib.h>#include <intrins.h>#include <stdio.h>/********************引脚定义********************/sbit RS =P3^0; //数据指令sbit RW =P3^1; //读写sbit E =P3^2; //使能sbit CSL =P3^3; //左片选sbit CSM =P3^4; //中片选sbit CSR =P3^5; //右片选unsigned char Page; //页地址unsigned char Col; //列地址unsigned char code BMP1[];unsigned char code BMP2[];void Delay(unsigned int MS);void wtcom(void);/***************************//*检查Busy *//***************************/void BusyL(void){CSL= 0;CSM= 1;CSR= 1;wtcom();}void BusyM(void){CSL= 1;CSM= 0;CSR= 1;wtcom();}void BusyR(void){CSL= 1;CSM= 1;CSR= 0;wtcom();}void wtcom(void){RS = 0; //指令RW = 1;P1 = 0xFF; //输出0xff以便读取正确E = 1;_nop_();while(P1 & 0x80); //Status Read Bit7 = BUSYE = 0;_nop_();}/********************************************************//*根据设定的坐标数据，定位LCM上的下一个操作单元位置*//********************************************************/void Locatexy(void){unsigned char x,y;switch (Col&0xc0) /* col.and.0xC0*/{ /*条件分支执行*/case 0: {BusyL();break;}/*左区*/case 0x40: {BusyM();break;}/*中区*/case 0x80: {BusyR();break;}/*右区*/}x = Col&0x3F|0x40; /* col.and.0x3f.or.Set Y Addres s*/y = Page&0x07|0xB8; /* row.and.0x07.or.set Page */wtcom(); /* waitting for enable */RS = 0; //指令RW = 0; //写P1 = y; //设置页面地址E = 1;_nop_();E = 0;_nop_();wtcom(); /* waitting for enabl e */RS = 0;RW = 0;P1 = x; //设置列地址E = 1;_nop_();E = 0;_nop_();}/***************************//*写指令*//***************************/void WriteCommandL( unsigned char CommandByte ){BusyL();P1 = CommandByte;RS = 0; //指令RW = 0;E = 1;_nop_();E = 0;_nop_();}void WriteCommandM( unsigned char CommandByte ){BusyM();P1 = CommandByte;RS = 0; //指令RW = 0;E = 1;_nop_();E = 0;_nop_();}void WriteCommandR( unsigned char CommandByte ){BusyR();P1 = CommandByte;RS = 0; //指令RW = 0;E = 1;_nop_();E = 0;_nop_();}/***************************//*读数据*//***************************/unsigned char ReadData( void ){unsigned char DataByte;Locatexy(); /*坐标定位，返回时保留分区状态不变*/RS = 1; /*数据输出*/RW = 1; /*读入*/P1 = 0xFF; //输出0xff以便读取正确E = 1; /*读入到LCM*/_nop_();DataByte = P1; /*数据读出到数据口P1 */E = 0;_nop_();return DataByte;}/***************************//*写数据*//***************************/void WriteData( unsigned char DataByte ){Locatexy(); /*坐标定位，返回时保留分区状态不变*/RS = 1; /*数据输出*/RW = 0; /*写输出*/P1 = DataByte; /*数据输出到数据口*/E = 1; /*写入到LCM*/_nop_();E = 0;_nop_();}void LcmClear( void ){Page = 0;Col = 0;for(Page=0;Page<8;Page++)for(Col=0;Col<192;Col++)WriteData(0);}void LcmInit( void ){WriteCommandL(0x3f); //开显示WriteCommandM(0x3f);WriteCommandR(0x3f);WriteCommandL(0xc0); //设置起始地址=0WriteCommandM(0xc0);WriteCommandR(0xc0);WriteCommandL(0x3f); //开显示WriteCommandM(0x3f);WriteCommandR(0x3f);LcmClear();Col = 0;Page= 0;Locatexy();}void LcmPutDots( unsigned char DotByte ){Page = 0;Col = 0;for(Page=0;Page<8;Page++){for(Col=0;Col<192;Col++){WriteData( DotByte );DotByte = ~DotByte;}}}void LcmPutBMP( unsigned char *puts ){unsigned int X=0;Page = 0;Col = 0;for(Page=0;Page<8;Page++){for(Col=0;Col<192;Col++){WriteData( puts[X] );X++;}}}void LcmReverseBMP( void ){unsigned char temp;Page = 0;Col = 0;for(Page=0;Page<8;Page++){for(Col=0;Col<192;Col++){temp = ReadData(); //空读一次temp = ReadData();temp = ~temp;WriteData(temp);}}}void Delay(unsigned int MS){unsigned char us,usn;while(MS!=0){usn = 2; //for 12Mwhile(usn!=0){us=0xf6;while (us!=0){us--;};usn--;}MS--;}}void Main( void ){Delay(200); //等待复位LcmInit();LcmClear();while(1){LcmPutBMP(BMP1);Delay(1500);LcmReverseBMP();Delay(1500);LcmPutBMP(BMP2);Delay(1500);LcmReverseBMP();Delay(1500);}}unsigned char code BMP1[]={/*-- 宽度x高度=192x64 --*/0xFF,0x01,0xFD,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05, 0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0x05,0xFD,0x01,0xFF, 0xFF,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x10,0xF8,0x00,0x00,0x00, 0x00,0x00,0x00,0xE0,0x10,0x08,0x08,0x08,0x08,0x10,0xE0,0x00,0x00,0x70,0x08,0x08, 0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x80,0x60,0x10,0x08,0x08,0x08,0x08,0x30,0x00,0x00,0x00,0x00,0xC0,0x20,0x10, 0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x82,0x42,0x32,0x3E,0x56,0x92,0x52,0x32, 0x12,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x04,0x04,0xFC,0x04,0x04,0x04,0xFC, 0x04,0x84,0xC4,0x20,0x10,0x08,0x86,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x80, 0x80,0x80,0x80,0x7E,0x90,0x90,0x90,0x90,0xD0,0x08,0x00,0x00,0x00,0x00,0x00,0xFC, 0x04,0x44,0xB4,0x0E,0x10,0x10,0xF0,0x1C,0x16,0xD0,0x10,0x10,0x10,0x08,0x00,0x00, 0x00,0x00,0x20,0xE0,0xFE,0xA0,0x18,0x28,0xE8,0x48,0x5E,0x48,0x48,0x5F,0x48,0xE8, 0x04,0x00,0x00,0x00,0x40,0x40,0x40,0xFE,0x40,0x60,0x60,0x20,0x20,0xFE,0x22,0x20, 0x20,0x20,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0xFF, 0xFF,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0xFF,0x80,0x80,0x00, 0x00,0x00,0x00,0x61,0x82,0x84,0x84,0x84,0x44,0x32,0x0F,0x00,0x00,0xC0,0xA0,0x90, 0x88,0x84,0x83,0xE0,0x00,0x00,0x00,0x81,0xC3,0xA5,0x18,0x18,0xA5,0xC3,0x81,0x00, 0x00,0x3F,0x42,0x81,0x81,0x81,0x81,0x42,0x3C,0x00,0x00,0x0C,0x0B,0x08,0x88,0x88, 0xFF,0x88,0x88,0x00,0x00,0x00,0x00,0xFF,0x08,0x04,0x02,0x22,0x25,0x24,0x69,0x42, 0x02,0x06,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x80,0x61,0x1F,0x01,0x01,0x01,0xFF, 0x01,0x08,0x08,0x84,0x82,0x41,0x20,0x18,0x00,0x00,0x00,0x00,0x00,0x80,0x1F,0x1F, 0x10,0xD0,0x10,0x10,0x10,0xD0,0x10,0x10,0x1F,0x40,0x80,0x00,0x00,0x00,0x00,0xFF, 0x10,0x10,0x10,0x1F,0x20,0x23,0x22,0x22,0x22,0xFF,0x22,0x22,0x22,0x11,0x10,0x00, 0x00,0x18,0x06,0x01,0xFF,0x00,0x03,0x20,0x2F,0x25,0xE5,0x3D,0x25,0x65,0xA5,0x27, 0x10,0x10,0x00,0x00,0x40,0x60,0x20,0x3F,0x24,0x14,0x94,0xC4,0x64,0x1F,0x0C,0x14, 0x64,0xC4,0x83,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0xFF, 0xFF,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x01, 0x02,0x02,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x01,0x00,0x00, 0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x00,0x03, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x01, 0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x02,0x02,0x01,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x01,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0xFF, 0xFF,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x10,0x10,0x90,0xF0,0xB0,0x90,0x90,0x90,0x90, 0x10,0x10,0x10,0xF0,0x00,0x00,0x00,0x00,0x20,0x20,0xE0,0x20,0x20,0x20,0xE0,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20, 0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0xF0,0x00,0xC0,0x40,0x40,0x40,0xF0,0x40,0x40,0xF8,0x40,0x40,0x20, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x10,0x00,0x10, 0x60,0x40,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0xFF, 0xFF,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x44,0x22,0x11,0x11,0x2A,0x24,0x4A,0x11,0x10, 0x30,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x08,0xFF,0x08,0x08,0x08,0xFF,0x08, 0x44,0x46,0x21,0x10,0x08,0x04,0xC4,0x00,0x00,0x00,0x00,0x00,0x20,0xCF,0x09,0x09, 0xF9,0x19,0x09,0x09,0xF9,0x09,0x09,0x8F,0x60,0x00,0x00,0x00,0x00,0x04,0x04,0x04, 0xC4,0x74,0x14,0x04,0x04,0xFC,0x04,0x04,0x14,0x24,0x44,0x84,0x02,0x00,0x00,0x00, 0xC0,0x31,0x0F,0xFF,0x05,0x18,0x01,0x7F,0x2A,0x2A,0xEA,0x2A,0x2A,0x2A,0x3F,0x80, 0x80,0x00,0x00,0x00,0x01,0x11,0x11,0xF1,0x11,0x11,0x09,0x01,0x03,0x7F,0xC1,0x01, 0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0xFF, 0xFF,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x08,0x08,0x08,0x09,0x09,0x09,0x0B,0x0A,0x08, 0x08,0x08,0x08,0x0F,0x00,0x00,0x00,0x08,0x04,0x03,0x00,0x00,0x00,0x00,0x0F,0x10, 0x10,0x08,0x04,0x04,0x02,0x01,0x00,0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x0B,0x08, 0x0F,0x08,0x08,0x08,0x0F,0x0A,0x09,0x08,0x08,0x0C,0x08,0x00,0x00,0x04,0x02,0x01, 0x00,0x00,0x00,0x08,0x18,0x0F,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x00,0x00,0x00, 0x00,0x00,0x00,0x1F,0x10,0x10,0x11,0x09,0x09,0x07,0x01,0x01,0x03,0x05,0x09,0x18, 0x08,0x00,0x00,0x04,0x0C,0x04,0x04,0x03,0x02,0x02,0x02,0x02,0x01,0x00,0x01,0x03, 0x04,0x08,0x1E,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0xFF, 0xFF,0x80,0xBF,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0, 0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xA0,0xBF,0x80,0xFF,};unsigned char code BMP2[]={/*-- 宽度x高度=192x64 --*/0xFF,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01, 0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0xFF, 0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x80,0xC0,0xC0,0xA0,0xB0,0x90,0x98,0x98,0x9C,0x9C,0xBC,0xBC,0x38,0x58,0x98,0x18, 0x30,0xE0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xF0,0xF0,0xF0,0xF0,0xF0,0xF0,0xFC,0xFC, 0xFC,0xFC,0xFC,0xFC,0xF8,0xF0,0xF8,0xF8,0xFC,0xF8,0xF8,0xF8,0xF0,0xC0,0x80,0x80, 0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFC,0xFE,0x06,0x06,0x06,0x0C, 0x0C,0x98,0xF8,0xE0,0xF0,0xF0,0xF0,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8, 0xF8,0xF8,0xF0,0xF0,0xF0,0xE0,0xF0,0xF8,0x98,0x0C,0x0C,0x06,0x06,0x06,0xFE,0xFC, 0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xC0,0xC0,0xA0,0xB0,0x90,0x98,0x98,0x9C,0x9C, 0xBC,0xBC,0x38,0x58,0x98,0x18,0x30,0xE0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF, 0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x42, 0x81,0xFD,0x83,0xC1,0xFC,0xE2,0xC1,0xFE,0x61,0x40,0xFF,0xE1,0xC1,0xE2,0xC6,0x8D, 0xF0,0xC0,0x01,0x3F,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x80,0x80,0x80,0xE0,0xF8,0xF8,0xFC,0xFF,0xFF,0xFF,0xFF,0xF1,0x00,0x00,0x03,0x03, 0x33,0x33,0x03,0x03,0x03,0x33,0x33,0x07,0x03,0x01,0xC1,0xE1,0xF3,0xFF,0xFF,0xFF, 0xFF,0xFF,0xFE,0xE0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xCF,0xFC,0xF8,0xFE, 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF, 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFC,0xF8,0xF8,0x9E,0x07,0x01, 0x00,0x00,0x00,0x00,0x7C,0x42,0x81,0xFD,0x83,0xC1,0xFC,0xE2,0xC1,0xFE,0x61,0x40, 0xFF,0xE1,0xC1,0xE2,0xC6,0x8D,0xF0,0xC0,0x01,0x3F,0xFE,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF, 0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x1F,0x3F,0xE5,0xCB,0x8F,0x23,0x40,0x20,0x85,0x8B,0xCF,0xE1,0xF3,0xFF, 0xFF,0xFF,0xC0,0xFE,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xF9,0xFF,0xFF,0xFF,0xFF,0xFF,0x0F,0x07,0x03,0x00,0x00,0x00,0x00, 0x00,0x30,0x28,0x28,0x38,0x30,0x00,0x00,0x00,0x00,0x03,0x07,0x0F,0x3F,0xFF,0xFF, 0xFF,0xFF,0xFF,0xF7,0xE3,0x00,0x00,0x00,0x00,0x20,0x20,0x20,0x7F,0xFF,0xFF,0xFF, 0xFF,0x83,0x01,0x01,0x01,0x31,0x79,0x31,0x83,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF, 0xCF,0x23,0x71,0x71,0x21,0x01,0x01,0x03,0x87,0xFF,0xFF,0xFF,0xFF,0x7F,0x40,0x40, 0x40,0x40,0x40,0x00,0x00,0x00,0x00,0x00,0x1F,0x3F,0xE5,0xCB,0x8F,0x23,0x40,0x20, 0x85,0x8B,0xCF,0xE1,0xF3,0xFF,0xFF,0xFF,0xC0,0xFE,0xFF,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF, 0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x3C,0x52,0xF9,0x80,0x00,0x03,0x05,0x05,0x03,0x01,0x00,0x40,0xE1,0xA3, 0x57,0x3F,0x1F,0x0F,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xF8,0xF8,0xF8, 0xF8,0xF8,0xF0,0x00,0x00,0x00,0x80,0xE0,0x28,0x27,0xE0,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0xC1,0x03,0x9F,0x3F,0x7F,0x7F,0x7F,0xFC,0xF8,0xF0,0xE0,0xC0,0x80,0x80, 0x80,0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0xC0,0xE0,0xF0,0xF8,0xFC,0xFF,0xFF, 0xFF,0xFF,0xFF,0x3F,0x03,0x00,0x00,0x00,0x00,0x10,0x10,0x18,0x08,0x0D,0x07,0x07, 0x0F,0x1F,0x1F,0x3E,0x3E,0x7E,0x7E,0x7F,0xFF,0x7F,0x7F,0x7D,0x7C,0x7C,0x7D,0x7F, 0x7F,0xFF,0x7E,0x7E,0x7E,0x7E,0x3E,0x3F,0x1F,0x1F,0x0F,0x0F,0x09,0x10,0x10,0x20, 0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x52,0xF9,0x80,0x00,0x03,0x05,0x05, 0x03,0x01,0x00,0x40,0xE1,0xA3,0x57,0x3F,0x1F,0x0F,0x07,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF, 0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x03,0x7E,0x86,0x0E,0x1E,0x8E,0x06,0x02,0xC2,0x7F,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x03,0x03, 0x03,0x03,0x05,0x04,0x04,0x07,0x05,0x02,0x00,0x00,0xFD,0x00,0x00,0x00,0x00,0x00, 0xAC,0x03,0x00,0x00,0x3F,0x00,0x00,0x00,0x01,0x03,0x87,0xAF,0x0F,0xFF,0x0F,0x07, 0x1F,0x1F,0xBF,0x3F,0x3F,0x3F,0xDF,0x0F,0x0F,0x1F,0x1F,0xFF,0x0F,0x0F,0x07,0x01, 0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x70,0xE0,0x80, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xF6,0xC6,0x3E,0x7E,0x7E,0x7E,0x32, 0x86,0xFF,0xFE,0xF0,0xF0,0xF0,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x7E,0x86,0x0E,0x1E, 0x8E,0x06,0x02,0xC2,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF, 0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x53,0x4E,0x40,0x7F,0x80,0x80,0x9F,0xA0,0xC0, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x08,0x08,0x08,0x08,0x08, 0x0B,0x00,0x06,0x00,0x03,0x04,0x04,0x0C,0x04,0x0C,0x1D,0x05,0x00,0x57,0xE0,0xC0, 0xC0,0x54,0x7B,0x00,0x1C,0x24,0x27,0x40,0x20,0x40,0x40,0x63,0x24,0x18,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01, 0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x03,0x01,0x03,0x3F,0x7F,0x7F,0x7E,0x7E,0x7F, 0x63,0x03,0x03,0x03,0x03,0x03,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x53,0x4E,0x40, 0x7F,0x80,0x80,0x9F,0xA0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0xFF, };。