汽车焊装相关英语词汇表(全)

焊接专业英语词汇（共10部分）焊接专业英语词汇（共10部分）1、熔化焊熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequence/deposition sequence焊缝倾角weld slope/inclination of weld axis焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。

如水平固定管所进行的环缝焊接向下立焊vertical down welding/downward welding in the vertical position向上立焊vertical up welding/upward welding in the vertical position倾斜焊inclined position welding上坡焊upward welding in the inclined position下坡焊downward welding in the inclined position对接焊butt welding角焊fillet welding搭接焊lap welding船形焊fillet welding in the downhand position/fillet welding in the flat position平角焊horizontal fillet welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊flare groove welding卷边焊flanged edge welding纵缝焊接welding of longitudinal seam横缝焊接welding of transverse seam-环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seam环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊foreward welding (英国)/ forehand welding (美国)后倾焊backward welding(英国)/ backhand welding(美国)分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding右焊法rightward welding/backhand welding挑弧焊whipping method自动焊automatic welding手工焊manual welding/hand welding车间焊接shop welding工地焊接site welding(英国)/ field welding (美国)拘束焊接restraint welding堆焊surfacing/building up/overlaying隔离层堆焊buttering端部周边焊boxing/end return返修焊rewelding补焊repair welding塞焊plug welding槽焊slot welding衬垫焊welding with backing焊剂垫焊welding with flux backing窄间隙焊narrow-gap welding强制成形焊enclosed welding脉冲电弧焊pulsed are welding-电弧点焊arc spot welding螺柱焊stud welding热风焊hot gas welding高能焊high grade energy welding固态焊接solid-state welding单面焊双面成形one-side welding with back formation焊接条件welding condition焊接工艺参数welding parameter极性polarity正接electrode negative/straight polarity反接electrode positive/reversed polarity运条方式manipulation of electrode焊接电流welding current焊接电流增加时间welding current upslope time焊接电流衰减时间welding current downslope time电流密度current density短路电流short circuit current脉冲电流pulse level/pulse current level脉冲电流幅值pulse current amplitude基值电流background level脉冲频率pulse frequency脉冲焊接电流占空比duty cycle of pulse duration电弧电压arc voltage再引弧电压reignition voltage焊接速度welding speed行走速度rate of travel/travel speed送丝速度wire feed rate线能量heat input/energy input热输入heat input预热preheat后热postheat焊后热处理posweld heat treatment/postheat treatment预热温度preheat temperature层间温度interpass temperature焊接终了温度finishing temperature后热温度postheating temperature焊丝伸出长度wire extension弧长arc length熔化速度melting rate熔化时间melting time熔化系数melting coefficient熔敷速度rate of deposition/deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency-损失系数loss coefficient飞spatter飞溅率spatter loss coefficient融合比fusion ratio稀释dilution稀释率rate of dilution合金过度系数transfer efficiency/recovery (of an element)坡口groove坡口面groove face坡口面角度angle of bevel (英国)/ bevel angle (美国)坡口角度included angle(英国)/groove angle(美国)坡口高度groove depth钝边root face钝边高度thickness of root face/width of root face根部间隙root gap(英国)/root opening (美国)根部半径root radius/groove radius根部锐边root edge卷边高度height of flange卷边半径radius of flange单面坡口single groove双面坡口double groove坡口形式groove typeI形坡口square grooveV形坡口single V grooveY形坡口single V groove with root face双Y形坡口double Vgroove with root face带钝边U形坡口single U groove带钝边双U形坡口double U grooveVY形坡口single compound angle groove带钝边J形坡口single J groove带钝边双J形坡口double J groove单边V形坡口single bevel groove双V形坡口double V groove不对称双V形坡口asymmetric double V groove双单边V形坡口double bevel groove/K groove带垫板V形坡口V groove with backing/ single V groove with backing喇叭形坡口flare groove锁底坡口single bevel groove with backing locked坡形板边tapered edge焊缝weld接逢seam焊缝符号welding symbol焊缝金属weld metal填充金属filler metal-熔敷金属deposited metal焊缝表面weld face/ face of weld焊缝背面back of weld焊缝轴线axis of weld焊缝尺寸size of weld焊缝宽度weld width/ width of weld焊缝长度weld length/ length of weld焊缝有效长度effective length of weld焊缝厚度throat depth/ throat thickness焊缝计算厚度theoretical throat焊缝实际厚度actual throat熔深penetration/ depth of penetration焊缝成形appearance of weld焊缝成形系数form factor of weld余高reinforcement/ excess weld metal背面余高root reinforcement削平焊缝flush weld/ weld machined flush对接焊缝butt weld角焊缝fillet焊脚leg/ fillet weld leg角焊缝断面形状profile of fillet weld平形角焊缝flat fillet凸形角焊缝convex fillet weld凹形角焊缝concave fillet weld角焊缝凹度concavity侧面角焊缝side fillet weld/ fillet weld in parallel shear正面角焊缝front fillet weld/ fillet weld in normal shear立角焊缝fillet weld in the vertical position横角焊缝fillet weld in the horizontal position平角焊缝fillet weld in the flat position斜角焊缝oblique fillet weld连续焊缝continuous weld断续焊缝intermittent weld连续角焊缝continuous fillet weld断续角焊缝intermittent fillet weld交错断续角焊缝staggered intermittent fillet weld并列断续角焊缝chain intermittent fillet weld端接焊缝edge weld卷边焊缝flanged edge weld塞焊焊缝plug weld纵向焊缝longitudinal weld横向焊缝transverse weld环行焊缝girth weld/ circumferential weld螺旋形焊缝spiral weld/ helical weld-密封焊缝seal weld承载焊缝strength weld联系焊缝connective weld定位焊缝tack weld焊道bead/ run/ pass焊波ripple焊根weld root/ root of weld焊趾weld toe/ toe封底焊道sealing run (after making main weld)/ back weld打底焊道backing weld (before making main weld)/ back weld根部焊道root pass/ root run填充焊道filling bead盖面焊道cosmetic bead/ cover pass回火焊道temper bead/ annealing bead熔透焊道penetration bead焊层layer焊接接头welded joint接头形状joint geometry等强匹配接头equalmatching weld joint低强匹配接头undermatching weld joint超强匹配接头overmatching weld joint接头根部root of joint对接接头butt jointI形对接接头square butt jointV形对接接头single V butt jointU形对接接头single U butt jointJ形坡口接头single J butt joint双V形对接接头double V butt joint双单边V形对接接头double bevel butt joint/ K groove butt joint带钝边U形对接接头double U butt joint带钝边J形坡口接头double J joint角接接头corner jointT形接头T joint斜T形接头inclined T joint十字接头cruciform joint/ cross-shaped joint三联接头joint among three members搭接接头lap joint套管接头muff joint/ sleeve joint双盖板接头double strapped joint盖板接头strapped joint端接接头edge joint卷边接头flanged edge joint锁底对接接头lock butt joint斜对接接头oblique butt joint-混合接头mixed joint/ composite joint有间隙接头open joint无间隙接头closed joint焊接电弧welding arc电弧形态arc shape电弧物理行为arc physics behaviour引弧striking arc引弧电压striking voltage电弧气氛arc atmosphere阴极cathode热阴极hot cathode冷阴极cold cathode阴极斑点cathode spot阴极区cathode region阴极区电场强度intensity of the electric field in the cathode region阴极压降cathode drop阳极anode阳极斑点anode spot斑点压力spot pressure阳极区anode region阳极区电场强度intensity of the electric field in the anode region阳极压降anode drop弧柱arc column/ arc stream弧柱压降voltage drop in arc column弧柱电位梯度potential gradient in the arc column弧焰arc flame弧心arc core硬电弧forceful arc/ hard arc软电弧soft arc旋转电弧rotating arc脉冲电弧pulsed arc脉冲喷射电弧pulsed spray arc起皱现象puckering phenomena起皱电弧puckering arc起皱临界电流puckering critical current间接电弧indirect arc压缩电弧compressive arc磁控电弧magnetic controlling arc电弧力arc force电磁力electromagnectic force电磁收缩效应pinch effect电弧飘移wandering of arc电弧稳定性arc stability电弧静特性static characteristic of arc-电弧动特性dynamic characteristic of arc最小电压原理principle of minimum voltage电弧挺度arc stiffness电弧偏吹arc blow磁偏吹magnetic blow阴极清理作用cleaning action of the cathode电弧自身调节arc self-regulation挖掘作用digging action极性效应polarity effect熔滴droplet熔滴比表面积specific surface of droplet熔滴过渡metal transfer过度频率transition frequency粗滴过渡globular transfer; drop transfer短路过渡short circuiting transfer喷射过渡spray transfer旋转喷射过渡rotating spray transfer脉冲喷射过渡pulsed spray transfer爆炸过渡explosive transfer渣壁过渡flux wall guided transfer熔池molten pool沸腾状熔池boiling molten pool弧坑crater熔渣slag渣系slag system渣系相图slag system diagram碱性渣basic slag酸性渣acid slag碱度basicity酸度acidity长渣long slag短渣short slag粘性熔渣viscous slag氧化物型熔渣oxide melting slag盐型熔渣salt melting slag盐-氧化物型熔渣salt-oxide melting slag熔渣流动性fluidity of the slag; slag fluidity熔渣solidified slag多孔焊渣porous slag玻璃状焊渣vitreous slag自动脱落焊渣self-releasing slag脱渣性slag detachability焊接设备welding equipment; welding set焊机welding machine; welder-电焊机electric welding machine; electric welder焊接电源welding power source焊接热循环weld thermal cycle焊接温度场field of weld temperature; weld temperature field准稳定温度场quasi-stationary temperature field焊接热源welding heat source点热源point heat source线热源linear heat source面热源plane heat source瞬时集中热源instantaneous concentration heat source热效率thermal efficiency热能集中系数coefficient of heat flow concentration峰值温度peak temperature瞬时冷却速度momentary cooling rate冷却时间cooling time置换氧化substitutionary oxydation扩散氧化diffusible oxydation脱氧desoxydation先期脱氧precedent desoxydation扩散脱氧diffusible desoxydation沉淀脱氧precipitation desoxydation扩散氢diffusible hydrogen初始扩散氢initial diffusible hydrogen100℃残余扩散氢diffusible hydrogen remained at 100℃残余氢residual hydrogen去氢dehydrogenation去氢热处理heat treatment for dehydrogenation脱硫desulphurization脱磷dephosphorization渗合金alloying微量合金化microalloying一次结晶组织primary solidification structure二次结晶组织secondary solidification structure联生结晶epitaxial solidification焊缝结晶形态solidification mode in weld-bead结晶层状线ripple多边化边界polygonization boundary结晶平均线速度mean solidification rate针状铁素体acicular ferrite条状铁素体lath ferrite侧板条铁素体ferrite side-plate晶界欣素体grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite粒状贝氏体granular bainite板条马氏体lath martensite-过热组织overheated structure魏氏组织Widmannst?tten structureM-A组元martensite-austenite constituent焊件失效分析failure analysis of weldments冷裂判据criterion of cold cracking冷裂敏感系数cold cracking susceptibity coefficient脆性温度区间brittle temperature range氢脆hydrogen embrittlement层状偏析lamellar segregation愈合healing effect断口金相fractography断口fracture延性断口ductile fracture韧窝断口dimple fracture脆性断口brittle fracture解理断口cleavage fracture准解理断口quasi-cleavage fracture氢致准解理断口hydrogen-embrittlement induced沿晶断口intergranular fracture穿晶断口transgranular fracture疲劳断口fatigue fracture滑移面断口glide plane fracture断口形貌fracture apperance断口试验fracture test宏观断口分析macrofractography放射区radical zone纤维区fibrous zone剪切唇区shear lip aone焊接性weldability使用焊接性service weldability工艺焊接性fabrication weldability冶金焊接性metallurgical weldability热焊接性thermal weldability母材base metal; parent metal焊接区weld zone焊态as-welded (AW)母材熔化区fusion zone半熔化区partial melting region未混合区unmixed zone熔合区bond area熔合线weld junction (英)；bond line (美)热影响区heat-affected zone (HAZ)过热区overheated zone粗晶区coarse grained region-细晶区fine grained region过渡区transition zone硬化区hardened zone碳当量carbon equivalent铬当量chromium equivalent镍当量nickel equivalent舍夫勒组织图Schaeffler's diagram德龙组织图Delong’s diagram连续冷却转变图（CCT图）continuous cooling transformation裂纹敏感性cracking sensibility焊接裂纹weld crack焊缝裂纹weld metal crack焊道裂纹bead crack弧坑裂纹crater crack热影响区裂纹heat-affected zone crack纵向裂纹longitudinal crack横向裂纹transverse crack微裂纹micro-crack; micro-fissure热裂纹hot crack凝固裂纹solidification crack晶间裂纹intercrystalline crack穿晶裂纹transcrystalline crack多边化裂纹polygonization crack液化裂纹liquation crack失延裂纹ductility-dip crack冷裂纹cold crack延迟裂纹delayed crack氢致裂纹hydrogen-induced crack焊道下裂纹underbead crack焊根裂纹root crack焊趾裂纹toe crack锯齿形裂纹chevron cracking消除应力处理裂纹stress relief annealing crack (SR crack)再热裂纹reheat crack焊缝晶间腐蚀weld intercryctalline corrosion刀状腐蚀knife line attack敏化区腐蚀weld decay层状撕裂lamellar tearing焊接性试验weldability裂纹试验cracking testIIW裂纹试验IIW cracking testY形坡口裂纹试验slit type cracking test分块形槽热裂纹试验segmented circular groove cracking testH形裂纹试验H-type cracking test-鱼骨形裂纹试验fishbone cracking test指形裂纹试验finger (cracking) testT形裂纹试验Tee type cracking test环形槽裂纹试验circular-groove cracking test可调拘束裂纹试验varestraint testBWRA奥氏体钢裂纹试验BWRA cracking test for austenitie steel圆棒裂纹试验bar type cracking test; round bar cracking test里海裂纹试验Lehigh restraint cracking test圆形镶块裂纹试验circular-path cracking test十字接头裂纹试验cruciform cracking testZ向窗口拘束裂纹试验Z-direction window type restraint cracking testG-BOP焊缝金属裂纹试验G-BOP weld metal crack test巴特尔焊道下裂纹试验Battelle type underbead cracking testU形拉伸试验U-tension test缪雷克期热裂纹试验Murex hot cracking test菲斯柯裂纹试验FISCO (type) cracking testCTS裂纹试验controlled thermal severity拉伸拘束裂纹试验（TRC试验）tensile restraint cracking test刚性拘束裂纹试验（RRC试验）rigid restraint cracking test插销试验implant testTigamajig 薄板焊接裂纹试验Tigamajing thin plate cracking test焊道纵向弯曲试验longitudinal-bead test柯麦雷尔弯曲试验Kommerell bead bend test肯泽尔弯曲试验Kinzel test缺口弯曲试验notch bend test热朔性试验hot-ductility test热影响区冲击试验impact test of HAZ热影响区模拟试验synthetic heat-affected zone test最高硬度试验maximum hardness test落锤试验NRL (Naval Research Laboratory)测氢试验Hydrogen test焊接材料电极焊接材料welding consumables电极electrode熔化电极consumable electrode不熔化电极nonconsumable electrode钨电极tungsten electrode焊丝welding wire. Welding rod实心焊丝solid wire渡铜焊丝copper-plating welding wire自保护焊丝self-shielded welding wire药芯焊丝flux-cored wire复合焊丝combined wire-堆焊焊丝surfacing welding rod填充焊丝filler wire焊条electrode/ covered electrode焊芯core wire药皮coating (of an electrode)/ covering (of an electrode)涂料coating flux/coating material造气剂gas forming constituents造渣剂slag forming constituents合金剂alloying constituent脱氧剂dioxidizer稳弧剂arc stabilizer粘接剂binder水玻璃water glass水玻璃模数modules of water glass酸性焊条acid electrode高钛型焊条high titania (type) electrode钛钙型焊条lime titania type electrode钛铁矿形焊条ilmenite type electrode氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode高纤维素型焊条high cellulose (type) electrode石墨型焊条graphite type electrode碱性焊条basic electrode/ lime type covered electrode低氢型焊条low hydrogen type electrode高韧性超低氢焊条high toughness super low hydrogen electrode奥氏体焊条austenitic electrode铁素体焊条ferritic electrode不锈钢焊条stainless steel electrode珠光体耐热钢焊条pearlitic heat resistant steel electrode低温钢焊条low temperature steel electrode/ steel electrode for low temperature铝合金焊条aluminum alloy arc welding electrode铜合金焊条copper-alloy arc welding electrode铜芯铸铁焊条cast iron electrode with steel core纯镍铸铁焊条pure nickel cast iron electrode球墨铸铁焊条electrode for welding spheroidal graphite cast iron铸芯焊条electrode with cast core wire镍基合金焊条nickel base alloy covered electrode蒙乃尔焊条Monel electrode纯铁焊条pure iron electrode渗铝钢焊条alumetized steel electrode高效率焊条high efficiency electrode铁粉焊条iron powder electrode底层焊条backing welding electrode深熔焊条deep penetration electrode重力焊条gravity electrode-立向下焊条electrode for vertical down position welding节能焊条saving energy electrode水下焊条underwater welding electrode耐海水腐蚀焊条seawater corrosion resistant steel electrode低尘低毒焊条low-fume and harmfulless electrode/low-fume and low-toxic electrode堆焊焊条surfacing electrode耐磨堆焊焊条hardfacing electrode钴基合金堆焊焊条cobalt base alloy surfacing electrode碳化钨堆焊焊条tungsten carbide surfacing electrode高锰钢堆焊焊条high manganese steel surfacing electrode双芯焊条twin electrode绞合焊条stranded electrode编织焊条braided electrode双层药皮焊条double coated electrode管状焊条flux-cored electrode气渣联合保护型药皮semi-volatile covering焊条工艺性usability of the electrode/ technicality of the electrode焊条使用性running characteristics of an electrode/ operating characteristics of an ele ctrode焊条熔化性melting characteristics of an electrode焊条直径core diameter焊条偏心度eccentricity (of an electrode)药皮重量系数gravity coefficient of coating焊条药皮含水量percentage of moisture for covering焊条夹吃持端bare terminal (of an electrode)焊条引弧端striking end (of an elcetrode)焊剂welding flux/ flux熔炼焊剂fused flux粘结焊剂bonded flux烧结焊剂sintered flux/ agglomerated flux窄间隙埋弧焊焊剂flux for narrow-gap submerged arc welding低氢型焊剂low hydrogen type flux高速焊剂high speed welding flux无氧焊剂oxygen-free flux低毒焊剂low poison flux磁性焊剂magnetic flux电弧焊arc welding直流电弧焊direct current arc welding交流电弧焊alternating current arc welding三相电弧焊three phase arc welding熔化电弧焊arc welding with consumable金属极电弧焊metal arc welding不熔化极电弧焊arc welding with nonconsumable-碳弧焊carbon arc welding明弧焊open arc welding焊条电弧焊shielded metal arc welding (SMAW)重力焊gravity welding躺焊fire cracker welding电弧堆焊arc surfacing自动堆焊automatic surfacing躺板极堆焊surfacing by fire cracker welding带极堆焊surfacing with band-electrode振动电弧堆焊vibratory arc surfacing耐磨堆焊hardfacing埋弧焊submerged arc welding (SAW)多丝埋弧焊multiple wire submerged arc welding纵列多丝埋弧焊Tandem sequence (submerged-arc welding)横列多丝埋弧焊series submerged arc welding (SAW-S)横列双丝并联埋弧焊transverse submerged arc welding热丝埋弧焊hot wire submerged-arc welding窄间隙埋弧焊narrow-gap submerged arc welding弧压反馈电弧焊arc voltage feedback controlling arc welding自调节电弧焊self-adjusting arc welding适应控制焊接adaptive control welding焊剂层burden; flux layer气体保护电弧焊gas shielded arc welding保护气体protective atmosphere惰性气体inert-gas活性气体active-gas惰性气体保护焊inert-gas (arc) welding氩弧焊argon arc welding熔化极惰性气体保护电弧焊metal inert-gas arc welding钨极惰性气体保护电弧焊tungsten inert-gas arc welding钨极氢弧焊argon tungsten arc welding脉冲氢弧焊pulsed argon arc welding熔化极脉冲氢弧焊argon metal pulsed arc welding钨极脉冲氢弧焊argon tungsten pulsed arc welding热丝MIG焊hot wire MIG welding热丝TIG焊hot wire TIG welding氨弧焊helium-arc welding活性气体保护电弧焊metal active-gas arc welding混合气体保护电弧焊mixed gas arc welding二氧化碳气体保护电弧焊carbon-dioxide arc welding; CO2 arc welding细丝CO2焊CO2 arc welding with thin wire粗丝CO2焊CO2 arc welding with thick wire磁性焊剂CO2焊unionarc welding-药芯焊丝CO2焊arcos arc process; dual shield arc welding气电立焊electrogas (arc) welding氮弧焊nitrogen-arc welding水蒸气保护电弧焊water vapour arc welding原子氢焊atomic hydrogen welding冲器室中电弧焊controlled atmosphere arc welding旋转电弧焊rotating arc welding短路过渡电弧焊short circuiting arc welding焊丝横摆频率weaving speed of wire焊丝停摆时间electrode keep time of slider等离子弧焊plasma arc welding (PAW)等离子弧plasma arc等离子流plasma jet转移弧transferred arc非转移弧nontransferred arc联合型等离子弧combined plasma arc主弧main arc维弧pilot arc维弧电流pilot arc surrent双弧现象double arcing双弧临界电流critical current of double arcing等离子弧焊枪plasma (welding) torch压缩喷嘴constricting nozzle单孔喷嘴single port nozzle多孔喷嘴multiport nozzle压缩喷嘴孔径orifice diameter孔道长度orifice throat length孔道比orifice throat ratio等离子气plasma gas; orifice gas电极内缩长度electrode setback小孔效应keyhole effect小孔型等离子弧焊keyhole-mode welding熔透型等离子弧焊fusion type plasma arc welding大电流等离子弧焊high-current plasma arc welding中电流等离子弧焊intermediate-current plasma arc welding小电流等离子弧焊low-current plasma arc welding微束等离子弧焊micro-plasma arc welding交流等离子弧焊AC plasma arc welding脉冲等离子弧焊pulsed plasma arc welding等离子弧堆焊plasma arc surfacing热丝等离子弧堆焊hot wire plasma arc surfacing粉末等离子弧堆焊plasma arc powder surfacing等离子-熔化极惰性气体保护电弧焊plasma MIG welding转移弧电源transferred arc power supply-非转移弧电源nontransferred arc power supply电弧焊设备arc welding equipment电弧焊机arc welding machine直流弧焊机DC arc welding machine交流弧焊机AC arc welding machine交直流两用弧焊机AC/DC arc welding machine单站弧焊机single operator arc welding machine多站弧焊机multi-operator arc welding set固定式弧焊机stationary arc welding machine移动式弧焊机portable arc welding machine台式弧焊机bench arc welding machine内燃机驱动式弧焊机combustion engine driven arc welding set电动机驱动式弧焊机motor driven arc welding set熔化极弧焊机arc welding machine using a consumable electrode不熔化极弧焊机arc welding machine using a non-consumable electrode脉冲弧焊机pulsed arc welding machine气体保护弧焊机gas shielded arc welding machine氩弧焊机argon arc welding machine二氧化碳弧焊机CO2 arc welding machine钨极惰性气体保护弧焊机tungsten inert-gas welding machine熔化仍惰性气体保护弧焊机metal inert-gas welding machine气电立焊机electrogas (arc) welding machine等离子弧焊机plasma arc welding machine微束等离子弧焊机micro-plasma welding equipment原子氢焊机atomic hydrogen welding apparatus埋弧焊机submerged arc welding machine弧焊电源arc welding power source直流弧焊电源DC arc welding power source交流弧焊电源AC arc welding power source交直流两用弧焊电源AC/DC arc welding power source脉冲弧焊电源pulsed arc welding power source上升特性弧焊电源rising characteristic arc welding power source平特性弧焊电源constant –voltage arc welding power source下降特性弧焊电源dropping characteristic arc welding power source垂降特性弧焊电源constant-current arc welding power source多特性弧焊电源slope-controlled arc welding power source逆变式焊接电源inverter welding power source晶体管弧焊电源transistor arc welding power source电源动特性dynamic characteristic电源外特性external characteristic弧焊变压器arc welding transformer弧焊整流器arc welding rectifier硅弧焊整流器silicon arc welding rectifier晶闸管弧焊整流器SCR arc welding rectifier; arc welding silicon controlled rectifier-脉冲弧焊整流器pulsed arc welding rectifier弧焊发电机arc welding generator焊车welding tractor焊接机头welding head行走机构traveller送丝机构wire feeder等速送丝方式constant wire-feed system变速送丝方式alternate wire-feed system跟踪装置tracer焊丝盘wire reel焊钳electrode holder焊枪welding gun电极夹electrode holder导电嘴tip; contact tube喷嘴nozzle焊剂漏斗flux-hopper高频振荡器oscillator; HF unit脉冲引弧器pulsed arc starter; surge injector脉冲稳弧器pulsed arc stabilizer脉冲激弧器pulsed arc exciter输出电抗器out put reactor镇定变阻器ballast rheostat直流分量抑制器direct current suppressor焊接回路welding circuit额定焊接电流rated welding current焊接电流调节范围range of welding current regulation空载电压open circuit voltage(no load voltage)约定负载电压conventional load voltage负载持续率duty cycle额定负载持续率rated duty cycle; standard service手工弧焊机manual arc welding machine电焊渣electroslag welding (ESW)手工电渣焊manual electroslag welding丝极电渣焊electroslag welding with wire electrode板极电渣焊electroslag welding with plate electrode熔嘴电渣焊electroslag welding with consumable nozzle管极电渣焊electroslag welding with tube electrode窄间隙电渣焊narrow-gap electroslag welding电渣堆焊electroslag surfacing电渣焊机electrosalg welding machine熔嘴consumable nozzle; consumable wire钢档板steel shoe (钢冷却板Cu-cooling plate铜滑板copper shoe-渣池slag bath渣池深度depth of slag bath渣池电压voltage of slag bath电渣过程稳定性electroslag process stability焊丝间距distance between welding wires电子束焊electron beam welding (EBW)脉冲电子束焊pulsed electron beam welding加速电压acceleration voltage/ operating voltage电子束电流beam current电子束功率beam power电子束功率密度beam power density焦点focal spot焦距focal length工作距离work distance电子束焊机electron beam welding machine高真空电子束焊机full vacuum electron beam welder低真空电子束焊机partial vacuum electron beam welder非真空电子束焊机nonvacuum electron beam welder真空度vacuum电子枪electron gun二极电子枪diode gun三极电子枪triode gun偏压电极bias electrode电磁透镜electromagnetic lens电子束偏转线圈electron beam deflection coils导流系数perveance钉尖spiking激光焊laser welding/ laser beam welding连续激光焊continuous laser welding脉冲激光焊impulsed laser welding激光焊机laser welding equipment气体激光器gas laser固体激光器solid laser焦斑直径focussed diameter of the beam离焦量clearance between focal point and (plate) surface焊缝深宽比weld seam depth-to-width ratio-3、气焊、热剂焊、水下焊gas welding氧乙炔焊oxy-acetylene welding氢氧焊oxy-hydrogen welding空气乙炔焊air-acetylene welding氧乙炔焊oxy-acetylene flame氢氧焰oxy-hydrogen flame氧煤气焰oxy-coal gas flame焊接火焰welding flame混合比mixing ratio混合气体可燃范围inflammable limit of the gaseous一次燃烧primary combustion二次燃烧secondary combustion燃烧速度combustion rate燃烧强度combustion intensity火焰热效率flame heating efficiency焰芯inner cone; flame cone内焰internal flame外焰flame envelope中性焰neutral flame氧化焰oxidizing flame碳化焰carburizing flame回火flashback逆火backfire回烧flashback气体发生速度gasification speed焊炬torch; blow pipe等压式焊炬balanced pressure torch射吸式焊炬injector torch氧乙炔焊炬oxy-acetylene torch焊割两用炬combined cutting and welding torch混合室mixing chamber喷射器injector焊嘴welding nozzle; welding tip液氧气化器oxygen evaporator气瓶gas cylinder乙炔瓶acetylene cylinder阀罩cylinder cap气瓶阀cylinder valve汇流排cylinder manifold减压器pressure regulator; gas regulator单级减压器single stage regulator两级减压器two stage regulator回火防止器flashback arrestor-干式回火防止器dry flashback arrestor水封式回火防止器water-closing type arrestor净化器purifier乙炔发生器acetylene generator低压乙炔发生器low pressure acetylene generator热剂补焊thermit repair welding钢轨热剂焊thermit rail welding热剂thermit powder热剂钢水thermit steel热剂反应thermit reaction热剂溶渣thermit slag热剂铸模thermit mold; mold for thermit weld热剂坩埚thermit crucible焊筋collar水下焊underwater welding水下气体保护电弧焊underwater gas shielded arc welding水下等离子弧焊underwater plasma arc welding温式水下焊wet method underwater welding干式水下焊dry method underwater welding局部干式水下焊local dry underwater welding水帘局部干式水下焊water curtain type dry underwater welding4、压焊（电阻焊摩擦焊爆炸焊扩散焊超声波焊等）电阻焊resistance welding (RW)点焊spot welding; resistance spot welding凸焊projection welding缝焊seam welding滚点焊roll-spot welding连续点焊stitch welding多点焊multiple spot welding手压点焊push welding; poke welding脉冲点焊pulsation spot welding; multiple-impulse welding双面点焊direct spot welding单面点焊indirect spot welding串联点焊series spot welding多点凸焊multiple projection welding频道进缝焊step-by-step seam welding压平缝焊mash seam welding串联缝焊series seam welding对接缝焊butt seam welding; foil-butt seam电阻对焊upset butt welding闪光对焊flash butt welding (FBW)-储能焊stored energy welding电容储能点焊condenser discharge spot welding高频电阻焊high frequency resistance welding冲击电阻焊percussion welding胶接点焊spot weld-bonding; weld-bonding闪光flashing; flash过梁bridge; lintel顶锻upsetting; upset夹紧力clamping force顶锻力upsetting force; upset force电极压力electrode force; electrode pressure电极滑移electrode skid焊接循环welding cycle预压时间squeeze time锻压时间forge-delay time; forge time焊接通电时间（电阻焊）welding time (resistance welding)预热时间preheat time加热时间heat time冷却时间cool time间歇时间quench time; chill time回火时间temper time维持时间hold time休止时间off time闪光时间flash time; flashing time顶锻时间upset time; upsetting time有电顶锻时间upset current time无电顶锻时间upset current-off time闪光速度flashing speed闪光电流flashing current; flash current顶锻电流upset current预热电流preheat current回火电流temper current调伸长度initial overhange; extension闪光留量flash allowance顶锻留量upset allowance顶锻速度upset speed电极接触面electrode contact surface贴合面faying surface焊点welding spot熔核nugget熔核直径diameter of nugget塑性金属环区corona bond焊透率penetration rate压痕indentation。

汽车维修方面常用英语名词Abbreviation 省略；略语Abnormal combustion 异常燃烧Abnormal knocking 异响Abnormal motion 异常运动Abrasion 磨蚀，磨损，研磨Abrasion resistance 耐磨性、抗磨性Abrasion resisting properties 耐磨性Abrasion test 磨损试验Abrasive 磨料Abrasive cloth 砂布Abrasive paper 砂纸Abrasive powder 研磨粉Abrasive resistance 耐磨性Abrasive stick 油石、磨条Abrasive stone 油石Abrasive wear 磨损，磨蚀Abrasive wheel 磨轮，砂轮Abrator 抛丸清理机Abscissa 横坐标Absolute altitude 绝对高度Absolute humidity 绝对湿度Absolute motion 绝对运动Absolute pressure 绝对压力Absolute temperature 绝对温度Absolute unit 绝对单位Absolute value 绝对值Absolute velocity 绝对速度Absorb 吸收Absorbed power 吸收功率Absorbed torque （测功器）吸收扭矩Absorption 吸收Accel 加速器；加速踏板；催化剂Accelerated ageing 加速老化Accelerated life test 加速寿命试验Accelerated load test 加速负荷试验Accelerating ability 加速能力Accelerating jet 加速喷嘴Accelerating pump加速泵Accelerating resistance 加速阻力Accelerating winding加速线圈Acceleration 加速度Acceleration lane 加速车行道Acceleration limiter 加速限制器Acceleration meter加速度计Acceleration of vibration 振动加速度Acceleration performance 加速性Acceleration pickup加速度传感器Acceleration spectrum 加速度谱Acceleration vector of center of mass质心加速度矢量Accelerator （美）油门（踏板）Accelerator jet 加速喷嘴（量孔）Accelerator nozzle 加速喷嘴Accelerator pedal 加速踏板Accelerator pump加速泵Accelerator vacuum switch加速踏板真空开关Accel pedal 加速踏板，油门踏板Acceptance验收Acceptance test 验收试验Accessibility 可接近性Accessories附件Accessory device 附属装置Accident 意外，事故Accommodation 适应；调节作用；居住设备Accordion 可折叠的；折叠屏风Accordion coil 折形线圈Accordion door 折叠门Accordion partition 折叠隔板Accumulation wear average 累计平均磨耗Accumulator 蓄能器，蓄电池Accuracy 精度Accuracy class 精度等级Accuracy control 精确控制Accuracy of manufacture 制造精度Accuracy of measurement 测量精度Accuracy of positioning 定位精度Accuracy of reading 读数精度Accuracy of repetition 复制精度；重复精度Accuracy of thread 螺纹精度Aceton 丙酮Acetylene 乙炔AC generator 交流发电机Acid 酸Acid-proof alloy 耐酸合金Acid-proof pipe 耐酸管Acid tanker 酸罐车Acid vapour 酸罐汽Acme thread 梯形螺纹，爱克姆螺纹Acoustic absorption 吸音Acoustic insulation 隔音Acoustic panel 吸声板Acoustimeter 声级计，噪声计Acquisition 探测；搜索Acquisition of signal 信号采集Acre 英亩Acryl 丙烯酸树脂Active braking distance 有效制动距离Active braking time 有效制动时间Active suspension 主动悬架[挂]Actuating arm 驱动臂Actuating cam 致动凸轮Actuating line 促动管路Actuating motor 伺服电动机Actuating time 促动时间Actuator 执行机构，操作机构Actuator track 滑轨Adapter 接头；适配器Adapter plate 安装板，固定板Adapter ring 接合环Adapter sleeve 紧固套，连接套Addendum 齿顶高，齿顶Addendum circle 齿顶圆Addendum face 齿顶面Additional seat 附加座椅Additional temperature error 温度附加误差Additional wheel drive control 附加驱动车轮的操纵件Adhesion 附着；附着力；Adhesion coefficient 附着系数Adhesive 黏合剂Adiabatic 绝热的Adiabatic compression 绝热压缩Adjust 调整，调节，校正Adjustable 可调节的Adjustable brush 可调电刷Adjustable fork spanner 可调叉形扳手Adjustable pedal 可调踏板Adjustable reamer 可调铰刀Adjustable seat 可调节的座椅Adjustable shutter 可调百叶窗Adjustable spanner 活动扳手Adjustable stop screw 活动止动螺钉Adjustable wheel 可调式车轮Adjustable wrench 可调扳手，活扳手Adjusting 调整用的Adjusting cam 调整凸轮Adjusting hand wheel 调整手轮Adjusting lever 调整杆Adjusting nut 调整螺母Adjusting shim 调整垫片Adjusting spring 调整弹簧Adjusting washer 调整垫圈Adjustment 调整，调节Admission cam 进气凸轮Admission cam shaft 进气凸轮轴Admittance 导纳；加工余量；通道Advanced ignition 提前点火Advancer （点火）提前装置Advertising car 广告汽车Aerial 天线Aerial pollution 大气污染Aerodynamic angle of attack 气动迎角Aerodynamic body 流线形车身Aerodynamic drag 空气动力阻力Aerodynamic force 气动力Aerodynamic retarder 空气动力缓速装置[器] Aerodynamics 空气动力学Aero-stabilizer 气动力稳定装置Affinity 亲和力，亲和性After-burning 补燃，后燃，复燃After fire 消音器内爆炸；（点火开关切断后）自燃现象After-running 发动机惯性运转Age 年龄；老化；使用期限Age hardening 时效硬化Age resister 老化防止剂Aging 老化；时效Aiming of headlamp 前照灯对准Air bag （撞车保护用）气袋Air bleeding 放气Air bleed screw 放气螺钉Air bleed valve 空气溢流阀Air booster 气压助力器Air brake 空压制动Air brake actuator 气压制动执行器Air brake antifreeze tank 气压制动防冻液罐Air brake chamber 气压制动室Air brake equalizer 气压制动补偿器Air brake governor 气压制动调节器Air brake hose dummy coupling气压制动软件管（未连接时的）堵头Air brake reservoir pressure indicator 贮气简压力表Air brake valve 气制动阀Air braking system 气制动系Air bypass 空气旁路Air car 气垫汽车Air chamber type combustion chamber 空气室式燃烧室Air check valve （空气）单向阀Air choke 阻风门Air cleaner 空气滤清器Air cleaner bracket 空气滤清器支架Air cleaner cartridge 空气滤清器滤芯Air cleaner casing 空气滤清器外壳Air compression ga(u)ge 空气压力表Air compressor 空气压缩机Air conditioner 空调装置Air conditioning 空气调节Air conditioning control 空调装置操纵件Air cooler 空气冷却器Air cooling engine 风冷式发动机Aircraft shunt bus 机场联运客车Aircraft tire 航空轮胎Air damper 空气缓冲器Air dam skirt 气堰裙板，前阻风板Air deflector 导流板Air dryer 空气干燥器Air duct 通气道Air exhaust filter 排气滤清器Air feed pipe 送气管Air filter 空气滤清器Air filter tell-tale 空气滤清器警报灯Air flow meter 空气流量计Air fuel ratio 空气燃料比Air ga(u)ge 气压表Air gate 气流调节门Air governor 空气调速器Air gun 空气喷枪Air hammer 空气锤Air horn 气喇叭Air hose 空气软管Air injection 空气喷射Air inlet 进气口Air inlet port 进气孔Air insulation 空气绝缘Air intake 进气，吸气Air intake filter 进气滤清器Air leak 漏气Airless injection 无气喷射Air line lubricator 气压供油中央润滑系统Air lock 气阻，气障Air nozzle 喷气嘴Air outlet 出气口Air over hydraulic booster 气顶油助力器Air pipe 通气管Air pollution 大气污染Air pressure 气压Air pressure relay valve 气压继动阀Air quench hardening glass 风冷钢化玻璃Air regulating valve 空气调节阀Air relief cock 放气旋塞，放气开关Air required for combustion 燃烧必要空气量Air resistance 空气阻力Air speed governor 空气式调速器Air spoiler 空气阻流板Air sprayer 空气喷雾器Air spring 空气弹簧Air storage reservoir 储气罐Air strangler 阻风门Air strangler spindle 阻风门轴Air suction pipe 进气管，吸气管Air suspension 空气悬架[挂]Air tank 储气罐Air throttle valve 空气节气门Air-tight 气密的Air-tight chamber 气密室Air-tightness 气密性Air tube （轮胎）内胎Air valve 气阀，气门Air vent 通气孔Air wiper 压缩空气式刮水器Aisle 通道Alarm device 报警装置Alarm pressure 报警压力Alcohol 酒精Alcohol-blended fuel 掺酒精的燃料Align 调整，校直，定中心Aligner 定位器，校直器，调整器；前轮定位仪Aligning(torque) stiffness 回正（力矩）刚度Aligning (torque) stiffness coefficient 回正（力矩）刚度系数Aligning torque 回正力矩Aligning torque coefficient 回正力矩系数Alignment 定位，对中心Alignment check 定位检查Alkali 碱性，强碱Alkali degreater 碱脱油剂Alkali detergent 碱去垢剂Alkohol 乙醇，酒精All dog clutch transmission 全齿套变速器Allen wrench 内六角扳手Alligator bonnet 鳄口形发动机罩Alligator shears 鳄式剪床Allowable cargo load 容许载货量Allowable deflection 容许挠度[变位] Allowable dimension variation 允许尺寸偏差All-purpose adhesive 万能胶All-sponge rubber upholstery 全海绵橡胶汽车内饰All-steel body 全钢车身All synchromesh transmission 全同步器式变速器All-weather body 全天候车身All wheel drive 全轮驱动Alternating current 交流Alternator 交流发电机Altimeter 测高仪Altitude compensating 海拔补偿Altitude control device （化油器）适应高度控制油量的装置Aluminium alloy 铝合金Aluminium soap grease 铝基润滑脂Amber light 琥珀色灯光Ammeter 电流表，安培表Ammonia gas 氨（气）Ampere 安（培）Amplitude 振幅，幅度Anchor 支承销Anchor plate 支承板，支承块Angle bar 角铁Angle ga(u)ge 量角器，角度计Angle iron 角铁Angle of advance 提前角Angle of cone 锥角Angle of delay 滞后角Angle of friction 磨擦角Angle of lead 超前角Angle of lock 锁角Angle of repose 静止角Angle of retarded closing 延迟关闭角Angle of roll 侧倾角Angle of steering lock 最大转向角Angle of twist 扭转角Angular acceleration 角加速度Angular clearance 拔模斜度Angularity of connecting rod 连杆倾斜角Angular moment 转矩Angular momentum 角动量Angular wheel 圆锥齿轮Animal oil 动物油Anneal 退火Annealing 退火（作用）Annual average daily traffic 年平均日交通量Annual survey 年度检验Annular seat 环形座Annular spring 环形弹簧Annulus （行星齿轮系的）内齿环Ante-chamber 预燃室Antenna 天线Antibacklash spring 消隙弹簧Anti-blocking brake 防抱死制动器Anticorrosion 抗蚀性Anticorrosive oil 防锈油Antidazzle screen 遮阳板Antidazzle switch 变光开关Antidetonant 抗爆剂Anti-freezer 防冻器；防冻液Antifreezing solution 防冻液Antifriction alloy 耐磨合金Antifriction bearing 滚动轴承Antiknock gasoline 抗爆汽油Anti-knock nature 抗爆性Antiknock value 抗爆值Anti-lock brake sensor防抱死制动传感器Anti-lock brake system 防抱死制动系统Antioxidant 抗氧燃料Anti-rattle spring 防震弹簧Antiroll bar 防侧摆杆Antirust grease 防锈脂Antiscale agent 防垢剂Antiskid tread 防滑轮胎纹Antiskid tyre 防滑轮胎Anti-spatter compound 防溅剂Anti-squat 抗后坐Antiwear hydraulic oil搞磨液压油Aperture 孔，口，缝隙，孔径Apex 反射点；顶点，顶部；填充胶条Apex seal （转子）顶端密封垫片Appearance 外观，外形Appearance test 外观检验Application force 作用力Approach angle 接近角Apron 挡板；拖板箱Apron control 拖板控制Aquaplaning 水层效应；漂滑现象Aqueous ingredients 含水量Arbo(u)r 轴，心轴；芯骨Arbo(u)r press 手扳压床，矫正机Arc 电弧Arc welding 电弧焊Areometer 液体比重计Arm 臂Armature 电枢Armature changed type starter 电枢移动式起动机Armature core 电枢铁芯Armature reaction 电枢反应Armature shaft 电枢轴Armature spindle 电枢轴Armature terminal 电枢输出端接线柱Armature tester 电枢测试装置Armature winding 电枢绕组Arm of wheel 轮辐Armored motor car 装甲车Arm rest 肘靠Arm shaft 臂轴Arm support 肘靠Arm winker 臂式方向指示器Arrangement of camshaft 凸轮轴装置Articulated bus 铰接客车Articulated cross shaft 铰接式横轴Articulated jack 铰接式千斤顶Articulated joint 关节接合Articulated sixwheeler 铰接式六轮汽车Articulated utility carrier 铰接式通用载运车Articulation piece 铰接件Artificial gasoline 人造汽油Asbest(os) 石棉Asbestos-copper gasket 铜石棉衬垫Ash content 灰分，灰分量Ash tray 烟灰盘Aspect concrete pavement 沥青混凝土路面Asphalt distribution truck沥青洒布车Assembly 装配，总成Assembly belt 装配传送带Assembly conveyor 装配传送线Assembly drawing 装配图Assembly jig 装配夹具Assembly part 装配零件Assembly shop 装配车间Assist grip （副驾驶）扶手Asymmetrical beam 非对称光Asymmetric low beam headlamp 不对称近光束前照灯Asymptotic stability 渐近稳定性Atmospheric electricity 天电，大气电Atmospheric moisture 大气温度Atmospheric pressure compensating 气压补偿Atomising installation 喷雾装置Atomization 喷雾Atomizer 喷雾器Atomizer orifice 喷雾器喷嘴Atomizing chamber 雾化室Atomizing disc 雾化盘Attachment face 安装面Attendance 保养Audible warning (horn)control 音响警告（喇叭）操纵件Austenite 奥氏体Austenite steel 奥氏体钢Authorized maximum towed mass 允许最大拖挂质量Autobahn(德) 高速公路Autobicycle 摩托车，机器脚踏车Auto-body 汽车车身Autocorrelation 自相关Autocorrelation coefficient 自相关系数Autocorrelation function 自相关函数Autodrive 自动定速驾驶器Autolevelizer 自动水平调节器Autolift 举车器Automatic 自动的Automatic advance of ignition 自动提前点火Automatically advanced distributor 自动提前分电器Automatically timed magneto 自动正时磁电机Automatic antenna control 自动天线操纵杆Automatic braking system 自动制动系Automatic circuit breaker 自动断路器Automatic circulation 自动循环Automatic clutch 自动离合器Automatic control 自动操纵Automatic door closing device 自动关门装置Automatic door tell-tale 显示门未闭好的警报灯Automatic engine stop tell-tale 发动机自动停机警报灯Automatic gear change 自动换档Automatic gearbox indicator 变速器自动指示器Automatic jet control valve 自动喷孔控制阀Automatic level control 自动调平控制Automatic lubrication 自动润滑Automatic lubricator 自动润滑器Automatic mechanical transmission 自动换档机械式变速器Automatic mixture control 混合气浓度自动控制Automatic overdrive gear transmission 超越式自动变速器Automatic spark advancer 自动提前点火装置Automatic spark extinguisher 自动火花消除器Automatic starter 自动起动机Automatic steering 自动转向Automatic steering effect 自动转向(回位)效应Automatic switch 自动开关Automatic timing control 自动正时控制Automatic traffic control 自动交通管制Automatic transmission 自动变速器Automatic valve 自动阀门Automation 自动化Automobile 汽车Automobile fuel 汽车燃料Automobile styling 汽车造型Automotive body 汽车车身Automotive engineer 汽车工程师Automotive industry 汽车工业Automotive polish 汽车抛光剂Automotive trim 汽车内饰Automotive upholstery 汽车内饰件Autothermic piston 防热变形的活塞Auxiliary air valve 辅助空气阀Auxiliary box 分动箱Auxiliary brake 辅助制动器Auxiliary braking system 辅助制动系Auxiliary bulb 辅助灯泡Auxiliary combustion chamber 副燃烧室Auxiliary device 辅助装置Auxiliary exhaust 辅助排气,辅机排气Auxiliary field 辅助磁场Auxiliary filter 辅助过滤器Auxiliary frame 副车架Auxiliary fuel pump 副油泵Auxiliary headlamp 辅助前照灯Auxiliary transmission 副变速器Auxiliary valve 辅助阀Average cruising range 平均行驶范围Average speed 平均速度Awning 篷布,帐篷Awning pipe 篷杆Axial gas turbine 轴流式燃气轮机Axial pitch 轴向节距Axial thrust 轴向推力Axial water inlet 轴向进水口Axial whirl 轴向涡流Axis of rotation 旋转轴Axis pin 销轴Axis system 坐标系Axle 轴;车轴Axle bracket 轴架Axle distance 轴距Axle drive bevel pinion 主动锥齿轮Axle housing 桥壳Axle housing straightener 桥壳校直器Axle load 轴载荷Axle shaft 驱动轴,半轴Axle shaft gear 半轴齿轮,驱动轴齿轮Axle steer 轴转向Axle tube 半轴套管,轴管Axle wrench 轴盖扳手Baby car 微型小客车Baby truck 小型货车Back axle (汽车)后车轴Backbone frame 脊骨形底架Backbone tubular chassis 管状脊背底盘Backbone-type frame 中央梁式车架Backfire 回火,逆火Backfire check valve 防逆火单向阀Back gear 倒档Backing-off lathe 铲齿车床Backing-up lamp 倒车灯Back kick (发动机起动时)逆转Backlash 齿隙;侧向间隙Backlash adjusting screw 齿隙调节螺钉Backlash spring 消隙弹簧Back light 后窗玻璃Back mirror 后视镜Back noise 背景噪声Back panel 后围板Back plate (美) 制动底板;离合器盖Back pressure 背压,反压力Back pressure valve 背压阀Back rest 座椅靠背Back shaft 后轴Back scanner 后方障碍警报器Backspray 后溅Back squab 靠垫Back-up buzzer 倒车报警器Back-up light 倒车灯Back wall 后围Bad conductor 不良导体Bad land 崎岖地Baffle plate 隔板,导流板Baggage car 搬运车,行李车Bainite 贝氏体Bakelite 胶木;酚醛塑料Bakelite seal 胶木水封Baking 烤干Baking enamel 烘干瓷漆Balance 平衡Balance patch 平衡补片Balancer 平衡器;配重Balance shaft 平衡轴Balance weight 平衡重,平衡配量Balancing 平衡的Balancing machine 平衡机Balancing of mass 质量平衡Balancing patch 平衡片Balancing weight 平衡重Bald tire 花纹已磨光的轮胎Baling machine 包装机Ball and socket gear shifting 球座式换档装置Ball and trunion universal joint 球销式万向节Ballast resistor 附加电阻Ball bearing 球轴承Ball circuit screw 循环球螺杆Ball cup 球座Ball gear shift lever 环座式换档杆Ball cup 球座Ball gear shift lever 环座式换档杆Ball joint 球形接头Ball joint dust cover 球接头防尘套Ball knob for control lever 控制杆球头钮Ball-nut type steering gear 循环球式转向器Ballon tire 低压轮胎Ball pin 球头销Ball pivot 钢球支枢Ball race 球轴承座圈Ball retainer 轴承滚珠保持架Ball socket 球座,球窝Ball spline rzeppa universal joint 滚动花键球笼式万向节Ball stud 球头销Ball stud adjusting plug 球销调整旋塞Ball thrust bearing 推力球轴承Ball trunion 钢球支枢Ball valve 球(形)阀Ball yoke 球叉Band brake 带式制动器Band track 履带Band track chain (履带)防滑链Band type damper 板式阻尼器[减震器] Banisters 扶手Banjo (type) axle housing 整体式桥壳Bar 巴(压强单位);棒,条状物Bar iron 钢条,扁铁Barium carbonate 碳酸钡Barometer 气压计Barometric regulator 气压调节器Barrier 障碍物Base circle 基圆Bastard file 粗锉刀Batch manufacturing 批量生产Bath lubrication 油浴式润滑Bathtub type combustion chamber 浴缸式燃烧室Battery 蓄电池Battery box 蓄电池箱Battery car 电瓶车Battery cell 蓄电池单元Battery cell tester 蓄电池试验器Battery charger 充电机Battery charging condition indicator 蓄电池充电状况指示器Battery compartment 蓄电池箱Battery cover 蓄电池盖Battery cradle 蓄电池架Battery filling cap 蓄电池注液盖Battery ignition 蓄电池点火Battery plate 蓄电池极板Battery plug 电源接头Battery socket 电源插头Battery support 蓄电池托架Battery terminal 蓄电池接线柱Battery tray 蓄电池座盘Baulk ring 同步齿环Baume scale 波美比重计算尺Bayonet-coupled buld 卡口灯泡Bead 胎圈,胎缘Bead base 胎圈底部Bead core 胎圈芯Bead fit pressure 胎圈密合压力Bead heel 胎踵Beading machine 弯边路,卷边机Bead ring 钢丝圈Bead ring fracture 钢丝圈断裂Bead ring wrapper 钢丝圈缠绕布Bead roughness 胎圈凹凸不平Bead seat 胎圈座Bead toe 胎趾Bead width 胎圈宽度Bead wire core 胎缘钢丝芯Beam 梁,光束Beam adjusting disk plate 调光座盘Beam center 光束中心,亮区Beam of light (前照灯)光束Bearing 轴承Bearing bush 轴承套Bearing cap 轴承盖Bearing face 支承面Bearing friction 轴承摩擦Bearing lining machine 轴承浇铸机Bearing metal 轴承合金,轴瓦Bearing pressure 支承压力,轴承压力Bearing puller 轴承拆卸器Bearing retainer 轴承保持架Bearing spacer 轴承隔圈Bearing steel 轴承钢Bell crank 曲柄Bell frame 钟形架Bell housing 钟形外壳Bellows 风箱;波纹管Bellows thermostat 波纹管式节温器Bellows type pneumatic suspension 风箱式空气悬架Bellow type container 波纹管式容器Belt 皮带；(轮胎)带束层Belt conveyor 传送带Belt drive 皮带传动Belt drive fan 皮带驱动风扇Belt fastener 传动带接头Belt pulley 皮带轮Belt stretching device 传动带拉紧装置Belt tension 传动带张力Bench seat 长凳车座Bench test 台架试验Bending 弯曲Bending moment 弯矩Bending strength 抗弯强度Bending tester 弯曲试验机Bendix-type starter 惯性接合式起动机Bend of road 道路弯度Bend of spring 弹簧拱度Bent socket wrench 弯形套简扳手Bevel gear 锥齿轮Bevel gear lapping machine 锥齿轮研磨机Bevel gear wheel 大锥齿轮Bias 斜交,斜角Bias belted tire 带束斜交轮胎Bias fabric 斜经帘布Bias ratio 差速器锁止系数Bicycle 自行车Bicycle tire 自行车轮胎Big end (连杆)大头Big end bearing 大端轴承Bimetal 双金属,复合钢材Bimetal fuel ga(u)ge 双金属油量计Bimetallic oil pressure indicator 双金属式油压指示器Bimetallic oil pressure sensor 双金属式油压传感器Bimetal strip 双金属带Bimetal thermostat 双金属式节温器Binary alloy 二元合金Binary fuel 二元燃料Binding (车身)压条Binding end cap 压条封盖Binding screw 紧固螺钉Biotechnology 生物工艺学Bite 切削刀;腐蚀Bitone horn 双音喇叭Black nut 粗制螺母Blackout 防空灯火管制Black-out lamp 防空灯Black smoke 黑烟Blade 叶片Blade angles 叶片角Blade socket 片式插座Blade spacing 叶片间距Blade terminal 接线片;片式插头Bleeder 泄放器[阀,管];排放,放油[气] Bleeder cap 放气螺钉帽Bleeder connection 放泄接头Bleeder hose 放泄软管Bleeder tube 放气[油]管Bleeding 放气,抽气Bleed screw 排气螺塞Blind crack 细微裂纹Blind hole 不通孔,盲孔Blind rivet 盲孔铆钉Blinker 闪光信号灯Blinker bulh 闪光灯泡Blinker unit 闪光报警器Blister (内外轮胎内部)气泡Block ga(u)ge 块规Blow back (内燃机的)回爆Blow by (活塞环)漏气Blowby gas 漏气Blower 鼓风机Blow-fed engine 增压发动机Blowing torch 喷灯Blowoff cock 放泄旋塞Blowout 爆(胎)Blowout magneto 喷弧式磁电机Blowout of tire 轮胎爆破Blowtorch 喷灯;焊枪Blueprint 蓝图Blue smoke 蓝烟Bluff body 钝体(汽车造型)Blunt nose 钝头型(汽车造型)Boarding ladder 登车梯Body 身;车身Body accessories 车身附件Body-chassis frame construction 非承载式车身Body dent 车身凹坑Body frame 车身骨架Body insulation 车身隔热层Body lighting 车身照明Body panel 车身板件Body shell 车身本体Body side rack 车身侧架Body skeleton 车身骨架Body skirt 车身裙部Body stake 车身栅柱Body understructure 车身底架,车身底部构件Bodywork 车身制造Bogie unit 中后轴平衡悬挂Bolster 支承板;横梁;鞍座Bolster end cover 梁端盖板Bolster trailer 鞍座式挂车Bolster truck 鞍座式货车Bolster-type 鞍座式的Bolt 螺栓Bolt strap 螺柱连锁片Bond 粘接Bonded type lining 铸入式衬面Bond strap 搭铁线Bone 骨架Bonnet 发动机罩Bonnet prop 机罩支柱Bonnet side piece 发动机罩侧板Bonnet unlocking handle 发动机罩开锁把手Boost 增压Booster 增压器Booster pump增压泵Boot (汽车后部)行李箱;胎垫;皮套;防尘罩Borax 硼砂;四硼酸钠Bore 缸径;孔径Boring 钻孔,镗孔Boring machine 镗床;镗孔机Bottom dead center 下止点Bounce (簧上质量)跳动Bourdon tube pressure ga(u)ge 弹簧管式压力表Bowden cable 拉线Box body 箱式车身Box spanner 套简扳手Box truck 仓栅式货车Box-type frame 箱状车架Box wrench 套简扳手Brace 支柱;斜柱;支架;(货箱)定位拉条Bracket 支架;托架Braided wire 编织电线Brake 制动;制动器Brake action 制动作用Brake adjuster 制动调节器Brake and clutch reliner 制动器与离合器衬片拆换机Brake backing plate 制动器底板Brake band 制动带Brake band lining 制动带衬层Brake bleeding 制动器放气Brake booster 制动加力器Brake bottom plate 制动底板Brake cable 制动拉索Brake cable conduit 制动拉索管Brake caliper 制动钳Brake caliper plate yoke 制动钳板臂Brake cam 制动凸轮Brake camshaft 制动器凸轮轴Brake chamber 制动气室Blake chamber diaphragm 制动室膜片Brake chatter 制动颤振Brake clearance 制动间隙Brake compensating device 制动器均力装置Brake control 制动控制Brake control rod 制动控制杆Brake cross shaft 制动拉杆横轴Brake cylinder 制动缸Brake disc 制动盘Brake disc shield 制动盘护罩Brake distance 制动距离Brake drum 制动鼓Brake drum liner 制动鼓衬套Brake equalizer 制动器前后平衡装置Brake equalizer shaft 制动器平衡轴Brake fluid 制动液;刹车油Brake fluid reservoir 制动液贮存箱Brake flushing 制动器冲洗Brake force 制动力Brake gear 制动装置Brake hand control 手制动器控制杆Brake handle 制动手把Brake hop 制动跳跃,脱闸Brake horse power 制动马力Brake hose 制动软管Brake hysteresis 制动器滞后Brake judder 颤振Brake lamp 制动灯Brake lever 制动杆，制动手柄，制动踏板Brake lining 制动摩擦片Brake lining glue 制动摩擦片粘胶Brake lining grinding machine 制动器衬片研磨机Brake linkage 制动拉杆系统Brake master cylinder 制动主缸Brake noise 制动噪声Brake oil 制动油Brake operating valve 制动器操纵阀Brake pad 制动衬块；摩擦块Brake pad back plate 制动衬块［摩擦块］背板Brake pedal 制动踏板Brake pipe 制动管Brake pull rod 制动拉杆Brake quadrant 制动扇形齿轮板Brake ragging 制动拉杆系统Brake relining machine 铆制动蹄片机Brake rod 制动杆Brake shoe 制动蹄Brake shoe abutment 制动蹄支承座Brake shoe actuating camshaft 制动蹄促动凸轮轴Brake shoe carrier 制动蹄片座Brake shoe clearance 制动蹄间隙Brake shoe grinder 制动蹄片磨削装置Brake shoe holddown kit 制动蹄安装成套工具Brake shoe lining 制动蹄摩擦片Brake shoe link 制动蹄导板Brake shoe return spring 制动蹄回位弹簧Brake specific emission （制动）比排放量Brake stop 制动停车Brake system application time 制动机构滞后时间Brake tension rod 制动拉杆Brake tester 制动试验台Brake valve 制动阀Braking adhesion coefficient 制动附着系数Braking deviation 制动跑偏Braking distance 制动距离Braking drag 制动拖滞Braking efficiency factor 制动器效能因数Braking effort 制动力Braking equipment 制动装备Braking failure 制动失效Braking force 制动力Braking force coefficient 制动力系数Braking force distribution rate 制动力分配率Braking hop 制动跳动（间断离开地面）Braking jackknifing 制动折叠Braking line 制动管［线］路Braking nose dive 制动点头Braking power 制动功率Braking skid 制动滑移Braking stiffness 制动刚度Braking stiffness coefficient 制动刚度系数Braking system 制动系Braking system hysteresis 制动系滞后Braking time 制动时间Braking torque 制动力矩Braking trace 制动轨迹Braking vapour lock制动气阻Braking work 制动功Branch pipe 歧管Brass 黄铜Brazing 钎焊，铜焊Break away 侧滑Break bulk cargo carrier 厢式零担运输车Breakdown lorry 修理车Breakdown truck 抢修工程车Breaker 断电器；（轮胎）缓冲层Breaker cam 断电器凸轮Breakerless ignition system 无触点点火系统Breaker plate 断电器板Breaker point 断电器触点Breaker point gap 断电器触点间隙Breaker strip 缓冲胶片Breaking load 破坏负荷Breaking stength 断裂强度Breather 通风装置Breather tube 通气管Breathing mask 防毒面具Cab （公用，出租）汽车；驾驶室；化油器Cab assembly support 驾驶总成支座Cab-behind engine bus 长头式客车Cab body 驾驶室本体Cab closure 驾驶室隔板Cab guard 驾驶室防护板Cable 缆索；电缆Cable car 缆车Cable clip 缆索夹Cable conduit 缆索管道；电缆管道Cable laying equipment 电缆敷设设备Cable reel trailer 电缆卷筒挂车Cable shoe 电缆终端套管Cable support 缆索托架Cable terminal 电缆接头Cab lock tell-tale 驾驶室锁止警报灯Cab over 平头型（卡车）Cab over engine 平头驾驶室Cab-over-engine truck 平头式货车Cab-over-engine bus 平头式客车Cab over type body 平头型车身Cabriolet 活顶轿车Cab seat 司机座Cab tire 汽车轮胎Cab type body 箱形车身Cab warning 汽车（车内）报警器Cadmium plating 镀镉Cage 保持架Calcium carbide 碳货钙，电石Calibrated dial 校准刻度盘Calibration 校正；标定Caliper 卡钳，卡尺，圆规；制动钳Caliper disc brake 钳盘式制动器Caliper ga(u)ge 卡规Caliper plate 制动钳板Caliper rule 卡尺Caliper type brake 钳盘式制动器Calorie 卡（热量单位）Calorific value 发热量，热值Cam 凸轮Cam and lever type steering gear 蜗杆曲柄销式转向机构Cam and piston type hydraulic damper 凸轮活塞型液力减振器Cam angle 凸轮转角Cam bearer 凸轮支座Camber 车轮外倾Camber angle 车轮外倾角Cambered axle 有外倾车轮的轮轴Camber ga(u)ge （汽车前轮）外倾角测定器Camber of spring 板弹簧拱度Camber stiffness 外倾刚度Camber stiffness coefficient 外倾刚度系数Camber thrust 外倾推力Cam bowl 凸轮滚轮Cam brake 凸轮张开式制动器Cam controlled slide 凸轮控制滑块Cam disc 盘形凸轮Cam-driven fuel pump 凸轮驱动燃油泵Cam grinding 凸轮磨削Cam-ground piston 椭圆形活塞Camion 重型载货汽车，军用卡车Cam lobe crest 凸轮凸脊Cam of double lift 双级凸轮Camouflage 伪装，迷彩Camouflage net 伪装网Camp stool 折椅Cam ring 凸轮环；（叶片泵的）定子Cam roller 凸轮滚轮Camshaft 凸轮轴Cam shaft bearing 凸轮轴轴承Camshaft phasing gear 凸轮轴正时齿轮Camshaft sprocket 凸轮轴链轮Camshaft thrust washer 凸轮轴止推垫圈Camshaft timing gear 凸轮轴正时齿轮Camshaft turning lathe 凸轮轴车床Can 罐；罩，金属管壳Canibalize 汽车拆件拼装Canopy 顶盖；顶篷Canopy express truck 有篷的载货汽车Canopy top 盖式车顶Cantilever spring 悬臂弹簧Canvased light van 帆布篷轻型货车Canvas top 帆布车顶Cap 帽；盖Capacitor type flasher 电容式闪光器Capacity 容量Capacity factor （液力变矩器）能容系数Capacity of storage battery 蓄电池容量Capacity of tank 油箱容量Cape chisel 扁尖凿Cap nut 盖螺母Cap packing 盖衬垫Cap screw 有头螺灯Capstan 主动轴，主动轮；纹盘，起锚机Capstan nut 槽形螺母，带孔螺母Capstan winch 绞盘Capsule 囊；小容器；膜盒；膜片式传感器Car 汽车；轿车Caravan 大篷车；车队Car barn 车库Car body 车身Carbon 碳，积碳Carbon brush 碳刷Carbon brush holder 碳刷架Carbon deposit 积碳；碳质沉淀物Carbon dioxide 二氧货碳Carbon electrode 碳精电极Carbon fibre 碳纤维Carbonisation 碳化作用Carbonitriding 碳氨共渗；气体氰化Carbonization 碳化，渗碳；干馏Carbonized silicon 碳货硅，金刚砂Carbonized tungsten 一氧化碳Carbon pile regulator 碳堆式调节器Carbon-pile type current regulator 碳堆式电流调节器Carbon remover 除积碳器Carbon scraper 积碳刮除器Carbon steel 碳钢Carburet(t)er 化油器，汽化器Carburetion 汽化Carburetted air 增碳空气Carburetter air funnel 化油器空气进气喉管Carburetter body 化油器体Carburetter choke 化油器阻风门Carburetter engine 化油器式发动机Carburetter flange 化油器突缘Carburetter pipe wrench 化油器管扳手Carburizing by gas 气体渗碳Carcass 胎体，骨架Car container 汽车用集装箱Car cooler 汽车冷气设备Cardan 万向接头Cardan drive 万向节传动Cardan joint 万向节Cardan shaft 万向节传动轴Car floor 汽车底板Car ga(u)ge 汽车标准［规格，尺寸］Cargo floor 货箱底板Cargo gear （货物）装卸设备Cargo handling 货物装卸Cargo hatch 货舱口Cargo liner 定期运货汽车Car gondola 活底高边货车，无盖货车Cargo room 货舱Cargo truck 载货卡车Car heater 汽车暖风装置Car industry 汽车工业Car lift 举车器Car polish 汽车抛光腊Carport 敞开的汽画间；停车场Car radio 汽车收音机Carrige 车辆，铁路客车；刀架，溜板，滑动架Car trim 汽车装饰件Car trunk 汽车行李箱Car washer 洗车装置Car wax 车蜡Cascade 级联；串联Cascade control 级联控制Case-hardened steel 表面硬化钢Case hardening 表面硬化Case hardening steel 渗碳钢Casing 外壳Castellated nut 槽式螺母Caster (美) 主销后倾，主销后倾距；脚轮Caster angle 主销后倾角Caster camber ga(u)ge 主销后倾和前轮外倾角测量仪Caster effect of steering 主销后倾的转向效应Casting 铸件；铸造Casting machine of cylinders 缸套浇铸机Casting mo(u)ld 铸型Casting wheel 铸造车轮Cast iron 铸铁Cast iron liner 铸铁缸套Castle nut 槽顶螺母Cast steel 铸钢Cast steel spoke wheel辐条式铸钢轮辋Catalyst 催化剂，触媒Catalytic converter 催化转化器Catalytic cracking 催化裂化Catalytic postcombustion 催化后燃烧Caterpillar drive 履带驱动Cat's eye 小型反光镜Cattle transport truck 牲畜运输车Caution plate （汽车或机器上的）标牌C-clamp C形夹Ceiling lamp 顶灯Cell connector 电池连接条Cell cover 电池盖Cellophane 玻璃纸；胶膜Cement 水泥；黏结剂Cementation 渗碳Cementation flux 渗碳剂Cemented carbide tool 硬质合金刀具Cemented steel 渗碳钢Center bearing 中心轴承Center bolt 中心螺栓Center brake 中央制动器Center console 中央控制台Center drill 中心孔钻Center electrode 中心电极Center ga(u)ge 定中心规Center gear （行星齿轮机构的）中心轮，太阳轮Center hole grinder 中心孔磨床Centering ball （万向节）定心钢球Centering device 定中心装置Centering machine 打中心孔机Center lathe 普通车床Centerless grinding machine 无心磨床Center of air pressure 风压中心Center of gravity 重心Center of gyration 回转中心Center of mass 质量中心Center of oscillation 振荡中心Center of tire contact 轮胎接地中心Center pillar 中柱Center pole 中心极；中心柱Center post 中柱Centrifugal clutch 离心式离合器Centrifugal force 离心力Centrifugal governor 离心式调速器Centrifugal ignition advancer 离心式点火提前器Centrifugal moment 离心力矩Centrifugal oil filter 离心式机油滤清器Centrifugal pump离心泵Centrifugal pump runner 离心泵叶轮Centrifugal spark advancer 离心提前机构Centrifugal speed governor 离心式调速器Centrifugal supercharger 离心式增压器Centrifugal weight 离心重块，离心重锤Damper 减振器，阻尼器Damper oil 减振起油Damper pin 减振器销Damping 衰减；缓冲Dash board 仪表板，前围板Dash pot 缓冲简Data 数据；资料Data memory system 数据存储系统Deadener 消声材料Dead load 自重Dead weight 自重；净重Debonder （制动器蹄片）剥离器Deburring machine 去毛刺机Decompression cam 减压凸轮Decompression cock 减压旋塞Decompression shaft 减压轴Decontamination kit 清除沾染包Decorative moulding 装饰线条Decorative rib （轮胎侧）装饰线Decorative sidewall 装饰胎侧Defective 不合格的，故障的；次品Defectometer 探伤仪Deflection 挠度；挠曲；Deflection ratio （轮胎）下沉率Defogger 除雾器Deformation 变形Deformed steel 异型钢Defroster 除霜器，除霜装置Defroster control 除霜器控制器Defroster diffusor 除霜器扩散口。

冲压车间 Press Shop焊装车间 Body Shop涂装车间 Paint Shop总装车间 GA=general assembly 前地板 FF=front floor后地板 RF=rear floor内板 inner panel侧围 body side外板 outer panel 前围板 front panel 后围板 back panel 门槛 rocker panel侧围 body side下车体 underbody总成 assembly分总成 sub-assembly点焊 spot welding补焊 respot welding翼子板 fender汽缸 cylinder顶盖 roof天窗 sunroof机舱 motor compartment后备箱 deck lid白车身 BIW=body in white 夹具 tooling/jig涂胶 sealer滑橇 skid滑轨 slide主线 main line调整线 mental finish line 对中台 centering table 滚边 roller hemming滚床 roller bed地坑 pit滚头 roller head物流方向 logistic direction 视觉系统 vision system仿真 simulation地坑 pit踏台 platform钢结构 steel structure圆销 round pin菱形销 diamond pin椭圆销 slot pin固定销 fixed pin伸缩销 shift pin翻销 swing pin基准点系统 RPS=reference point system 上件导向 loading guide焊接导向 welding guide 夹紧 clamp抓手 Geo gripper弹簧 spring上件 load取件 unload流向 flow坐标 coordinate 品牌 brand料箱、料架 rack 顶升 eject/lift 铜 copper助力手/机械手 manipulator 厚度 thickness金属 metal铝 aluminum铜 copper铁 iron人机界面/接口 HMI=Human Machine Interface 同步工程 SE=simultaneous engineering重力输送 gravity conveyor通道 aisle/crane转台 rotate table磁铁 magnet支撑 supporter吸盘 vacuum限位块 stopper盲区 blind area三层焊 3 panels/3 layers welding 外购件 outsourcing吸盘 vacuum误差 error供应商质量管理 SQE=supplier quality engineering 混凝土 concrete磁条 tape充电站 recharge station大件 big part小件 small part上件顺序 loading sequence点焊 spot welding下线工位 takeout station 螺栓/螺柱 bolt螺母 nut凸焊 projection welding 点焊 spot welding绝缘体 insulator铰链 hinge传感器 sensor气动 pneumatic/air control 折边胶 hemming sealer工艺卡 process sheet托盘 tray模板 template轮罩 wheel house激光扫描 laser scanning总拼工位 framing 图纸 drawing光栅 light curtain精度 precision/accuracyPLC=programmable logic controller 精定位台车 Geo pallet标牌 plate直径 diameter参数 parameter容积 capacity胶泵 sealer pump叉车 fork lift涂胶台 sealer table有效长度 useful length 防误防错 Poka yoke冲压 stamping叉车 fork lift。

汽车零部件生产术语
标题: 汽车零部件生产术语
1. 冲压 (Stamping): 将金属板材冲压成所需形状的工艺过程。

2. 焊接 (Welding): 利用高温将金属或合金材料熔化并连接的过程。

3. 铸造(Casting): 将熔融金属或合金倒入模具中,在其凝固后取出所需零件的工艺过程。

4. 机加工(Machining): 通过切削、镗孔、铣削等方式将金属、塑料等材料加工成所需形状。

5. 表面处理 (Surface Treatment): 如电镀、喷涂等工艺,为零件提供保护或装饰效果。

6. 装配 (Assembly): 将各个零部件按特定顺序组装在一起的过程。

7. 检测(Inspection): 对零部件进行尺寸、强度、外观等质量检测的过程。

8. 模具 (Mold/Die): 用于冲压、铸造等工艺的金属或合金模具。

9. 夹具 (Fixture): 用于固定工件进行加工或检测的工装夹具。

10. 自动化(Automation): 应用机器人、自动化生产线等先进技术实现自动化生产。

以上是汽车零部件生产中一些常见的术语和概念,旨在规范化生产流程,确保产品质量。

焊装线术语A/D/V Analysis/Development/Validation 分析/发展/验证AA Approve Architecture 审批体系ACD Actual Completion Date 实际完成日期ALBS Assembly Line Balance System 装配线平衡系统ANDON 暗灯AP Advanced Purchasing 提前采购API Advanced Product Information 先进的产品信息APQP Advanced Product Quality Planning 先期产品质量策划ATT Actual Tact Time 实际单件工时BIQ Building in Quality 制造质量BIW Body In White 白车身BOD Bill of Design 设计清单BOE Bill of Equipment 设备清单BOL Bill of Logistic 装载清单BOM Bill of Material 原料清单BOP Bill of Process 过程清单BPD Business Plant Deployment 业务计划实施CAD Computer-Aided Design 计算机辅助设计CAE Computer-Aided Engineering 计算机辅助工程(软件)CARE Customer Acceptance & Review Evaluation 用户接受度和审查评估CAS Concept Alternative Selection 概念可改变的选择CIP Continue Improve Process 持续改进CIT Compartment Integration Team 隔间融合为组CKD Complete Knockdown 完全拆缷CMM Coordinate Measuring Machines 坐标测量仪CPV Cost per Vehicle 单车成本CR&W Controls/Robotics & Welding 控制/机器人技术和焊接CS Contract Signing 合同签订CTD Cumulative Trauma Disadjust 累积性外伤失调CTS Component T echnical Specification 零件技术规格CVIS Completed Vehicle Inspection Standards 整车检验标准D/PFMEA Design/process failure mode & effects analysis 设计/过程失效模式分析DAP Design Analysis Process 设计分析过程DES Design Center 设计中心DFA Design for Assembly 装配设计DOE Design Of Experiments 试验设计DOL Die Operation Line-Up 冲模业务排行DPV Defect per Vehicle 单车缺陷数DQV Design Quality Verification 设计质量验证DRE Design Release Engineer 设计发布工程师DRL Direct Run Loss 直行损失率DRR Direct Run Run 直行率DSC Decision Support Center 决策支持中心ECD Estimated Completion Date 计划完成日期EGM Engineering Group Manager 工程组经理ELPO Electrode position Primer 电极底漆ENG Engineering 工程技术、工程学EOA End of Acceleration 停止加速EPC&L Engineering Production Cntrol &Logistics 工程生产控制和后勤EQF EarlyQuality Feedback 早期质量反馈EWO Engineering Work Order 工程工作指令FA Final Approval 最终认可FE Functional Evaluation 功能评估FEDR Functional Evaluation Disposition Report 功能评估部署报告FFF Free Form Fabrication 自由形态制造FIN Financial 金融的FL 听FMEA Failure Mode and Effects Analysis 失效形式及结果分析FPS Fixed Point Stop 定点停FTP File Transfer Protocol 文件传送协议FTQ First Time Quality 一次送检合格率GA General Assembly 总装GA Shop General Assembly Shop 总装车间Paint Shop 涂装车间Body Shop 车身车间Press Shop 冲压车间GCA Global Customer Audit 全球顾客评审GD&T Geometric Dimensioning & T olerancing 几何尺寸及精度GDS Global Delivery Survey 全球发运检查GM General Motors 通用汽车GMAP GM Asia Pacific 通用亚太GME General Motors Europe 通用汽车欧洲GMIO General Motors International Operations 通用汽车国际运作GMIQ General Motors Initial Quality 通用汽车初始质量GMPTG General Motors Powertrain Group 通用汽车动力组GMS Global Manufacturing System 通用全球制造系统GP General Procedure 通用程序GQTS Global Quality Tracking System 全球质量跟踪系统GSB Global Strategy Board 全球战略部HVAC Heating, Ventilation ,and Air Conditioning 加热、通风及空调I/P Instrument Panel 仪表板IC Initiate Charter 初始租约ICD Interface Control Document 界面控制文件IE Industrial Engineering 工业工程IEMA International Export Market Analysis 国际出口市场分析ILRS Indirect Labor Reporting System 间接劳动报告系统IO International Operations 国际业务IOM Inspection Operation Mathod 检验操作方法IOS Inspection Operation Summary 检验操作概要IPC International Product Center 国际产品中心IPTV Incidents Per Thousand Vehicles 每千辆车的故障率IQS Initial Quality Survey 初始质量调查IR Incident Report 事故报告ISP Integrated Scheduling Project 综合计划ITP Integrated Training Process 综合培训方法ITSD Interior Technical Specification Drawing 内部技术规范图IUVA International Uniform Vehicle Audit 国际统一车辆审核JES Job Element Sheet 工作要素单JIS Job Issue Sheet工作要素单JIT Just in Time 准时制JPH Job per hour 每小时工作量KCC Key Control Characteristics 关键控制特性KCDS Key Characteristics Designation System 关键特性标识系统KPC Key product Characteristic 关键产品特性LT Look at 看MFD Metal Fabrication Division 金属预制件区MFG Manufacturing Operations 制造过程MIC Marketing Information Center 市场信息中心MIE Manufacturing Integration Engineer 制造综合工程师MKT Marketing 营销MLBS Material Labor Balance System 物化劳动平衡系统MMSTS Manufacturing Major Subsystem Technical Specifications 制造重要子系统技术说明书MNG Manufacturing Engineering 制造工程MPG Milford Proving Ground 试验场MPI Master Process Index 主程序索引MPL Master Parts List 主零件列表MPS Material Planning System 原料计划系统MRD Material Required Date 物料需求日期MSDS Material Safery Data Sheets 化学品安全数据单MSE Manufacturing System Engineer 制造系统工程MSS Market Segment Specification 市场分割规范MTBF Mean Time Between Failures 平均故障时间MTS Manufacturing Technical Specification 生产技术规范MVSS Motor Vehicle Safety Standards 汽车发动机安全标准NAMA North American Market Analysis 北美市场分析NAO North American Operations 北美业务NAOC NAO Containerization NAO货柜运输NC Numerically Controlled 用数字控制NOA Notice of Authorization 授权书NSB NAO Strategy Board 北美业务部OED Organization and Employee Development 组织和员工发展OSH Occupational Safety & Health 职业安全健康OSHA Occupational Safety & Health Act 职业安全与健康法案OSHMS Occupational Safety & Health Management System 职业安全健康管理体系OSHS Occupational Safety & Health Standards 职业安全标准PA Production Achievement 生产结果PAA Product Action Authorization 产品临时授权PAC Performance Assessment Committee 绩效评估委员会PACE Program Assessment and Control Environment 项目评估和控制条件PAD Product Assembly Document 产品装配文件PARTS Part Readiness Tracking System 零件准备跟踪系统PC Problem Communication 问题信息PCL Production Control and Logistics 生产控制和支持PCM Process Control Manager 工艺控制负责人PCRProblem Communication Report 问题交流报告PDC Portfolio Development Center 证券发展中心PDM Product Data Management 产品资料管理PDS Product Description System 产品说明系统PDT Product Development Team 产品发展小组PED Production Engineering Department 产品工程部PEP Product Evaluation Program 产品评估程序PER Personnel 人员PET Program Execution Team 项目执行小组PGM Program Management 项目管理PI People Involement 人员参与PIMREP Project Incident Monitoring and Resolution Process 事故方案跟踪和解决过程PLP Production Launch Process 生产启动程序PMI Process Modeling Integration 加工建模一体化PMM Program Manufacturing Manager 项目制造经理PMR Product Manufacturability Requirements 产品制造能要求PMT Product Management Team 产品车管理小组POMS Production Order Management System 产品指令管理小组POP Point of Purchase 采购点PP Push - Pull 推拉PPAP Production Part Approval Process 生产零部件批准程序PPE 个人防护用品PPH Problems Per Hundred 百辆车缺陷数PPM Problems Per Million 百万辆车缺陷数PPS Practical Problem Solving 实际问题解决PR Performance Review 绩效评估PR/R Problem Reporting and Resolution 问题报告和解决PRTS Problem Resolution and Tracking System 问题解决跟踪系统PSC Portfolio Strategy Council 部长职务策略委员会PST Plant Support Team 工厂支持小组PTO Primary Tryout 第一次试验PTR Production Trial Run 生产试运行PUR Purchasing 采购PVD Production Vehicle Development 生产汽车发展PVM Programmable Vehicle Model 可设计的汽车模型QA Quality Audit 质量评审QAP Quality Assessment Process 质量评估过程QBC Quality Build Concern 质量体系构建关系QC Quality Characteristic 质量特性QCOS Quality Control Operation Sheets 质量风险控制QE Quality Engineer 质量工程师QET Quality Engineering Team 质量工程小组QFD Quality Function Deployment 质量功能配置QRD Quality, Reliability,andDurability 质量、可靠性和耐久力QS Quality System 质量体系QUA Quality 质量RC Review Charter 评估特许RCD Required Completion Date 必须完成日期RFQ Request For Quotation 报价请求RGM Reliability Growth Management 可靠性增长小组RONA Return on Net Assets 净资产评估RPO Regular Production Option 正式产品选项RQA Routing Quality Assessment 程序安排质量评定RT&TM Rigorous Tracking and Throughout Managment 严格跟踪和全程管理SDC Strategic Decision Center 战略决策中心SF Styling Freeze 造型冻结SIL Single Issue List 单一问题清单SIP Stansardized Inspection Process 标准化检验过程SIU Summing It All Up 电子求和结束SL System Layouts 系统规划SLT Short Leading Team 缩短制造周期SMARTSMBP Synchronous Math-Based Process 理论同步过程SME Subject Matter Expert 主题专家SMT Systems Management Team 系统管理小组SNR 坏路实验SOP Start of Production 生产启动SOP Safe Operating Practice 安全操作规程SOR Statement of Requirements 技术要求SOS Standardization Operation Sheet 标准化工作操作单SOW Statement of Work 工作说明SPA Shipping Priority Audit 发运优先级审计SPC Statistical Process Control 统计过程控制SPE Surface and Prototype Engineering 表面及原型工程SPO Service Parts Operations 配件组织SPT Single Point Team 专一任务小组SQA Supplier Quality Assurance 供应商质量保证（供应商现场工程师）SQC Supplier Quality Control 供方质量控制SQD Supplier Quality Development 供应方质量开发SQE Supplier Quality Engineer 供方质量工程师SQIP Supplier Quality Improvement Process 供应商质量改进程序SSF Start of System Fill 系统填充SSLT Subsystem Leadership Team 子系统领导组SSTS Subsystem Technical Specification 技术参数子系统STD Standardization 标准化STO Secondary Tryout 二级试验SUI 安全作业指导书SUW Standard Unit of Work 标准工作单位SWE Simulated Work Environment 模拟工作环境TAG Timing Analysis Group 定时分析组TBD To Be Determined 下决定TCS Traction Control System 牵引控制系统TDC Technology Development Centre 技术中心TDMF Text Data Management Facility 文本数据管理设备TG Tooling 工具TIMS Test Incident Management System 试验事件管理系统TIR Test Incident Report 试验事件报告TMIE Total Manufacturing Integration Engineer 总的制造综合工程TOE T otal Ownership Experience 总的物主体验TPM Total Production Maintenance 全员生产维护TSM Trade Study Methodology 贸易研究方法TT Tact Time 单件工时TVDE T otal Vehicle Dimensional Engineer 整车外型尺寸工程师TVIE Total Vehicle Integration Engineer 整车综合工程师TWS Tire and Wheel System 轮胎和车轮系统UAW United Auto Workers 班组UCL Uniform Criteria List 统一的标准表UDR Unverified Data Release 未经核对的资料发布UPC Uniform Parts Classification 统一零件分级VAE Vehicle Assembly Engineer 车辆装配工程师VAPIR Vehicle & Progress Integration Review Team 汽车发展综合评审小组VASTD Vehicle Assembly Standard Time Data 汽车数据标准时间数据VCD Vehicle Chief Designer 汽车首席设计师VCE Vehicle Chief Engineer 汽车总工程师VCRI Validation Cross-Reference Index 确认交叉引用索引VDP Vehicle Development Process 汽车发展过程VDPP Vehicle Development Production Process 汽车发展生产过程VDR Verified Data Release 核实数据发布VDS Vehicle Description Summary 汽车描述概要VDT Vehicle Development Team 汽车发展组VDTO Vehicle Development Technical Operations 汽车发展技术工作VEC Vehicle Engineering Center 汽车工程中心VIE Vehicle Integration Engineer 汽车综合工程师VIN Vehicle Identification Number 车辆识别代码VIS Vehicle Information System 汽车信息系统VLE Vehicle Line Executive 总装线主管VLM Vehicle Launch Manager 汽车创办经理VMRR Vehicle and Manufacturing Requirements Review 汽车制造必要条件评审VOC Voice of Customer 顾客的意见VOD Voice of Design 设计意见VS Validation Station 确认站VSAS Vehicle Synthesis,Analysis,and Simulation 汽车综合、分析和仿真VSE Vehicle System Engineer 汽车系统工程师VTS Vehicle Technical Specification 汽车技术说明书WBBA Worldwide Benchmarking and Business Analysis 全球基准和商业分析WOT Wide Open Throttle 压制广泛开放WPO Work Place Organization 工作场地布置WWP Worldwide Purchasing 全球采购COMMWIP Correction 纠错浪费Overproduction 过量生产浪费Material Flow 过度物料移动浪费Motion 过度移动浪费Waiting 等待浪费Inventory过度库存浪费Processing 过度加工浪费。

词汇整理冲压车间Press Shop焊装车间Body Shop涂装车间Paint Shop总装车间GA=general assembly前地板FF=front floor后地板RF=rear floor内板inner panel外板outer panel前围板front panel后围板back panel门槛rocker panel侧围bodyside下车体underbody总成assembly分总成sub-assembly点焊spot welding补焊respot welding翼子板fender汽缸cylinder顶盖roof天窗sunroof机舱motor compartment后备箱deck lid白车身BIW=body in white夹具tooling/jig涂胶sealer滑橇skid滑轨slide主线main line调整线mental finish line对中台centering table滚边roller hemming滚床roller bed滚头roller head物流方向logistic direction视觉系统vision system仿真simulation地坑pit踏台platform钢结构steel structure圆销round pin菱形销diamond pin椭圆销slot pin固定销fixed pin伸缩销shift pin翻销swing pin基准点系统RPS=reference point system上件导向loading guide焊接导向welding guide夹紧clamp抓手Geo gripper弹簧spring上件load取件unload流向flow坐标coordinate品牌brand料箱、料架rack顶升eject/lift助力手/机械手manipulator厚度thickness金属metal铝aluminum铜copper铁iron人机界面/接口HMI=Human Machine Interface同步工程SE=simultaneous engineering重力输送gravity conveyor通道aisle/crane转台rotate table磁铁magnet支撑supporter限位块stopper盲区blind area三层焊3 panels/3 layers welding外购件outsourcing吸盘vacuum误差error供应商质量管理SQE=supplier quality engineering 混凝土concrete磁条tape充电站recharge station大件big part小件small part上件顺序loading sequence下线工位takeout station螺栓/螺柱bolt螺母nut凸焊projection welding点焊spot welding绝缘体insulator铰链hinge传感器sensor气动pneumatic/air control折边胶hemming sealer工艺卡process sheet托盘tray模板template轮罩wheel house激光扫描laser scanning总拼工位framing图纸drawing光栅light curtain精度precision/accuracyPLC=programmable logic controller 精定位台车Geo pallet标牌plate直径diameter参数parameter容积capacity胶泵sealer pump涂胶台sealer table有效长度useful length防误防错Poka yoke冲压stamping叉车fork lift。

汽车装配专业词汇一、汽车零部件相关词汇。

1. engine [ˈendʒɪn]，名词，发动机。

2. chassis [ˈʃæsi]，名词，底盘。

3. body [ˈbɒdi]，名词，车身。

4. wheel [wiːl]，名词，车轮。

5. tire [ˈtaɪə(r)]，名词，轮胎（美语，英式为tyre）6. brake [breɪk]，名词/动词，刹车；制动。

- 例如：The brake system is very important for a car.（名词用法）- He braked suddenly.（动词用法）7. transmission [trænzˈmɪʃn]，名词，变速器。

8. axle [ˈæksl]，名词，车轴。

二、装配动作相关词汇。

1. assemble [əˈsembl]，动词，装配；组装。

- 例如：Workers assemble cars on the assembly line.2. install [ɪnˈstɔːl]，动词，安装。

- 例如：They install the engine into the chassis.3. mount [maʊnt]，动词，安放；安装。

- 例如：Mount the wheels on the axles.4. fasten [ˈfɑːsn]，动词，使固定；系紧。

- 例如：Fasten the bolts tightly.5. connect [kəˈnekt]，动词，连接。

- 例如：Connect the wires properly.三、装配工具相关词汇。

1. wrench [rentʃ]，名词，扳手。

2. screwdriver [ˈskruːdraɪvə(r)]，名词，螺丝刀。

3. bolt [bəʊlt]，名词，螺栓。

4. nut [nʌt]，名词，螺母。

5. rivet [ˈrɪvɪt]，名词，铆钉。

焊接专业英语词汇（焊接及相关工艺英文缩写）AW——ARC WELDING——电弧焊AHW——atomic hydrogen welding——原子氢焊BMAW——bare metal arc welding——无保护金属丝电弧焊CAW——carbon arc welding——碳弧焊CAW-G——gas carbon arc welding——气保护碳弧焊CAW-S——shielded carbon arc welding——有保护碳弧焊CAW-T——twin carbon arc welding——双碳极间电弧焊EGW——electrogas welding——气电立焊FCAW——flux cored arc welding——药芯焊丝电弧焊FCW-G——gas-shielded flux cored arc welding——气保护药芯焊丝电弧焊FCW-S——self-shielded flux cored arc welding——自保护药芯焊丝电弧焊GMAW——gas metal arc welding——熔化极气体保护电弧焊GMAW-P——pulsed arc——熔化极气体保护脉冲电弧焊GMAW-S——short circuiting arc——熔化极气体保护短路过度电弧焊GTAW——gas tungsten arc welding——钨极气体保护电弧焊GTAW-P——pulsed arc——钨极气体保护脉冲电弧焊MIAW——magnetically impelled arc welding——磁推力电弧焊PAW——plasma arc welding——等离子弧焊SMAW——shielded metal arc welding——焊条电弧焊SW——stud arc welding——螺栓电弧焊SAW——submerged arc welding——埋弧焊SAW-S——series——横列双丝埋弧焊RW——RWSISTANCE WELDING——电阻焊FW——flash welding——闪光焊RW-PC——pressure controlled resistance welding——压力控制电阻焊PW——projection welding——凸焊RSEW——resistance seam welding——电阻缝焊RSEW-HF——high-frequency seam welding——高频电阻缝焊RSEW-I——induction seam welding——感应电阻缝焊RSEW-MS——mash seam welding——压平缝焊RSW——resistance spot welding——点焊UW——upset welding——电阻对焊UW-HF——high-frequency ——高频电阻对焊UW-I——induction——感应电阻对焊SSW——SOLID STATE WELDING——固态焊CEW——co-extrusion welding——CW——cold welding——冷压焊DFW——diffusion welding——扩散焊HIPW——hot isostatic pressure diffusion welding——热等静压扩散焊EXW——explosion welding——爆炸焊FOW——forge welding——锻焊FRW——friction welding——摩擦焊FRW-DD——direct drive friction welding——径向摩擦焊FSW——friction stir welding——搅拌摩擦焊FRW-I——inertia friction welding——惯性摩擦焊HPW——hot pressure welding——热压焊ROW——roll welding——热轧焊USW——ultrasonic welding——超声波焊S——SOLDERING——软钎焊DS——dip soldering——浸沾钎焊FS——furnace soldering——炉中钎焊IS——induction soldering——感应钎焊IRS——infrared soldering——红外钎焊INS——iron soldering——烙铁钎焊RS——resistance soldering——电阻钎焊TS——torch soldering——火焰钎焊UUS——ultrasonic soldering——超声波钎焊WS——wave soldering——波峰钎焊B——BRAZING——软钎焊BB——block brazing——块钎焊DFB——diffusion brazing——扩散焊DB——dip brazing——浸沾钎焊EXB——exothermic brazing——反应钎焊FB——furnace brazing——炉中钎焊IB——induction brazing——感应钎焊IRB——infrared brazing——红外钎焊RB——resistance brazing——电阻钎焊TB——torch brazing——火焰钎焊TCAB——twin carbon arc brazing——双碳弧钎焊OFW——OXYFUEL GAS WELDING——气焊AAW——air-acetylene welding——空气乙炔焊OAW——oxy-acetylene welding——氧乙炔焊OHW——oxy-hydrogen welding——氢氧焊PGW——pressure gas welding——气压焊OTHER WELDING AND JOINING——其他焊接与连接方法AB——adhesive bonding——粘接BW——braze welding——钎接焊ABW——arc braze welding——电弧钎焊CABW——carbon arc braze welding——碳弧钎焊EBBW——electron beam braze welding——电子束钎焊EXBW——exothermic braze welding——热反应钎焊FLB——flow brazing——波峰钎焊FLOW——flow welding——波峰焊LBBW——laser beam braze welding——激光钎焊EBW——electron beam welding——电子束焊EBW-HV——high vacuum——高真空电子束焊EBW-MV——medium vacuum——中真空电子束焊EBW-NV——non vacuum——非真空电子束焊ESW——electroslag welding——电渣焊ESW-CG——consumable guide eletroslag welding——熔嘴电渣焊IW——induction welding——感应焊LBW——laser beam welding——激光焊PEW——percussion welding——冲击电阻焊TW——thermit welding——热剂焊THSP——THERMAL SPRAYING——热喷涂ASP——arc spraying——电弧喷涂FLSP——flame spraying——火焰喷涂FLSP-W——wire flame spraying——丝材火焰喷涂HVOF——high velocity oxyfuel spraying——高速氧燃气喷涂PSP——plasma spraying——等离子喷涂VPSP-W——vacuum plasma spraying——真空等离子喷涂TC——THERMAL CUTTING——热切割OC——OXYGEN CUTTING——气割OC-F——flux cutting——熔剂切割OC-P——metal powder cutting——金属熔剂切割OFC——oxyfuel gas cutting——氧燃气切割CFC-A——oxyacetylene cutting——氧乙炔切割CFC-H——oxyhydrogen cutting——氢氧切割CFC-N——oxynatural gas cutting——氧天然气切割CFC-P——oxypropanne cutting——氧丙酮切割OAC——oxygen arc cutting——氧气电弧切割OG——oxygen gouging——气刨OLC——oxygen lance cutting——氧矛切割AC——ARC CUTTING——电弧切割CAC——carbon arc cutting——碳弧切割CAC-A——air carbon arc cutting——空气碳弧切割GMAC——gas metal arc cutting——熔化极气体保护电弧切割GTAC——gas tungsten arc cutting——钨极气体保护电弧切割PAC——plasma arc cutting——等离子弧切割SMAC——shielded metal arc cutting——焊条电弧切割HIGH ENERGY BEAM CUTTING——高能束切割EBC——electron beam cutting——电子束切割LBC——laser beam cutting——激光切割LBC-A——air——空气激光切割LBC-EV——evaporative——蒸气激光切割LBC-IG——inert gas——惰性气体激光切割LBC-O——oxygen——氧气激光切割激光切割laser cutting(LC); laser beam cutting电子束切割electron beam cutting喷气激光切割gas jet laser cutting碳弧切割carbon arc cutting水下切割underwater cutting喷水式水下电弧切割waterjet method underwater arc cutting氧矛切割oxygen lancing; oxygen lance cutting溶剂氧切割powder lancing手工气割manual oxygen cutting自动气割automatic oxygen cutting仿形切割shape cutting数控切割NC (numerical-control) cutting快速切割high-speed cutting垂直切割square cut叠板切割stack cutting坡口切割beveling; bevel cutting碳弧气割carbon arc air gouging火焰气刨flame gouging火焰表面清理scarfing氧熔剂表面修整powder washing预热火焰preheat flame预热氧preheat oxygen切割氧cutting oxygen/ cutting stream切割速度cutting speed切割线line of cut/ cut line切割面face of cut/ cut face切口kerf切口上缘cutting shoulder切口宽度kerf width后拖量drag切割面平面度evenness of cutting surface/ planeness of cutting surface 割纹深度depth of cutting veins/ stria depth切割面质量quality of cut face上缘熔化度shoulder meltability/ melting degree of shoulder切口角kerf angle缺口notch挂渣adhering slag结瘤dross割炬cutting torch/ cutting blowpipe/ oxygen-fuel gas cutting torch割枪cutting gun割嘴cutting nozzle/ cutting tip快速割嘴divergent nozzle/ high-speed nozzle表面割炬gouging blowpipe水下割炬under-water cutting blowpipe水下割条electrode for under-water cutting粉剂罐powder dispenser数控切割机NC cutting machine门式切割机flame planer光电跟踪切割机photo-electric tracing cutting火焰切管机pipe flame cutting machine磁轮式气割机gas cutting machine with magnetic wheels 焊接结构welded structure/ welded construction焊件weldment焊接部件weld assembly组装件built-up member接头设计joint design焊接应力welding stress焊接瞬时应力transient welding stress焊接残余应力welding residual stress热应力thermal stress收缩应力contraction stress局部应力local stress拘束应力constraint stress固有应力inherent stress固有应变区inherent strain zone残余应力测定residual stress analysis逐层切割法Sach’s methodX射线衍射法X-ray stress analysis小孔释放法Mathar method固有应变法inherent strain method消除应力stress relieving局部消除应力local stress relieving应力重分布stress redistribution退火消除应力stress relieving by annealing温差拉伸消除应力low temperature stress relieving机械拉伸消除应力mechanical stress relieving应力松弛stress relaxation焊接变形welding deformation焊接残余变形welding residual deformation局部变形local deformation角变形angular distortion自由变形free deformation收缩变形contraction deformation错边变形mismatching deformation挠曲变形deflection deformation波浪变形wave-like deformation火焰矫正flame straightening反变形backward deformation焊接力学welding mechanics断裂力学fracture mechanics弹塑性断裂变形elasto-plastic fracture mechanics线弹性断裂力学linear elastic fracture mechanics延性断裂ductile fracture脆性断裂brittle fracture应力腐蚀开裂stress corrosion cracking热应变脆化hot straining embrittlement临界裂纹尺寸critical crack size裂纹扩展速率crack propagation rate裂纹张开位移（COD）crack opening displacement拘束度restraint intensity拘束系数restraint coefficient应变速率strain rate断裂韧度fracture toughness应力强度因子stress intensity factor临界应力强度因子critical stress intensity factors应力腐蚀临界应力强度因子critical stress intensity factor of stress corrosion cracking J积分J-integration罗伯逊止裂试验Robertson crack arrest testESSO试验ESSO test双重拉伸试验doucle tension test韦尔斯宽板拉伸试验Well’s wide plate test帕瑞斯公式Paris formula断裂分析图fracture analysis diagram焊接车间welding shop焊接工作间welding booth焊接工位welding post/ welding station焊接环境welding surroundings焊工welder电焊工manual arc welder气焊工gas welder焊接检验员weld inspector焊工培训welders training焊工模拟训练器trainer of synthetic weld焊工考试welder qualification test焊工合格证welder qualification/ welder qualified certification钢板预处理steel plate pretreatment喷沙sand blast喷丸shot blast矫正straighten开坡口bevelling (of the edge)/ chanfering装配assembly/ fitting安装erect刚性固定rigid fixing装配焊接顺序sequence of fitting and welding焊接工艺评定welding procedure qualification（转载自第一范文网，请保留此标记。

巨一自动化机器人事业部JEE Automation Robotics Division序号英文全称缩写中文全称备注A1 AC Gun 工频焊钳2 accuracy 精度3 acquisition of signal 信号采集4 aging 时效处理5 air 压缩空气6 air hoist 气动葫芦7 air spanner 气动扳手8 alternator 交流发电机9 alternator bracket 发动机支架10 anneal 退火11 anti-lock brake system ABS 防抱死刹车系统12 Arc Welding 弧焊13 ARM 电极臂14 assembly drawing 装配图15 asynchronous motor 异步电动机16 ATC 自动换枪装置17 Auto Gun 自动焊钳18 automatic feed 自动喂料19 automatic mechanical transmission AMT 自动换档机械式变速器20 automatic transmission AT 自动变速箱B21 ball bearing 球轴承22 bar 棒材23 billet 方钢24 black oxide coating 发黑/发蓝25 blank 坯料，半成品26 blanking 下料27 BODY IN WHITE BIW 白车身28 BODY INSPECTION FIXTURE 车身综合检具29 BODY RESPOT LINE 车身补焊线30 BODY SHOP 车身车间31 breaker 断电器32 brittleness 脆性33 BURR 毛刺C34 C Type Welding Gun C型焊枪35 calibration 校准36 capacity 容量，规格37 carbon-dioxide arc welding; CO2 arc welding 二氧化碳气体保护电弧焊MAG焊一种38 case hardening 表面硬化39 catalog 库40 chromium 铬41 clamping force 夹紧力42 Commission 现场调试43 Computer Aided Design CAD 计算机辅助设计44 Computer Numerical Control CNC 计算机数控加工45 concurrent engineering CE 并行工程46 configuration 组态47 control cabinet 控制柜48 control panel 控制屏，控制盘49 control System 操纵系统50 converter 变频器51 coordinate frame of car 车身坐标系52 cotter 开口销53 crack 裂纹54 current gauge 电流测试仪55 cycle time 节拍56 cylinder 气缸1 v1.0巨一自动化机器人事业部JEE Automation Robotics Division序号英文全称缩写中文全称备注D57 damped glue 膨胀减振胶58 data acquisition 数据采集59 data preprocessing 数据预处理60 data Processing 数据处理61 data processor 数据处理器62 DEBUG 程序调试63 definition 定义64 deflection /offset 偏移65 relay 延时66 DIE 冲模67 DIE CHANGER 模具交换器68 digital model 数模69 digital signal processing DSP 数字信号处理70 display 显示71 dowel pin 定位销72 duty ratio 负荷比E73 electric hoist 电动葫芦74 electric welding machine; electric welder 电焊机75 electrically operated valve 电控阀76 electrocladding /plating 电镀77 electrode holder 焊钳78 electromagnetic compatibility EMC 电磁兼容性79 engine 发动机80 epoxy resin glue for hemming 环氧折边胶F81 fault diagnosis 故障诊断82 feedback 反馈83 fender 防护板、翼子板84 field bus 现场总线85 fillet 角焊缝86 fillet welding 角焊87 flange 法兰88 FLEXIBLE BODY LINE FBL 柔性车身线89 flow chart 流程图90 frame/coordination 坐标91 friction stir welding 搅拌摩擦焊G92 gantry 龙门架93 gap 间隙94 gauge 型板95 gears 档位96 Geo-Gripper 定位抓具97 Geometry GEO 几何98 Geo-spot 定位焊点99 gluing 涂胶100 Gluing Robot 涂胶机器人101 governor 调速器102 grinder 磨光机103 gripper 抓具104 groove 坡口105 GUN HANGER 焊钳吊钩106 GUN SWITCH 焊钳开关H107 HAND GUN 手动焊钳108 HANDLING ROBOT 取件机器人；搬运机器人109 hardening and tempering 调质110 heat/thermal treatment 热处理2 v1.0巨一自动化机器人事业部JEE Automation Robotics Division序号英文全称缩写中文全称备注111 hemming 滚边112 HEMMING DIE 包边模具113 Hemming Machine 包边压力机114 HEMMING PRESS 包边压力机115 horizontal 水平116 hot-melt adhesive 热熔胶117 human-machine interface HMI 人机界面I118 induction machine 感应式电机119 information of weld point 焊点信息120 inner dimension 内部尺寸121 INSPECTION FIXTURE I/F 检具122 interference 干涉123 isolating transformer 隔离变压器J124 jog 点动（机器人等）125 joint 运动关节K126 kinematic 运动学的, 运动学上的L127 laser welding/ laser beam welding 激光焊128 layout 规划,布局图129 leg/ fillet weld leg 焊脚130 lifter 升降机131 linear unit 直线单元132 location 位置133 location pin 定位销134 lubricating oil 润滑油M135 main control point chart MCP图136 main reducer 主减速器137 man-machine coordination 人机协调138 MASTER CONTROL POINT MCP 主要控制点139 MASTER CONTROL SECTION MCS 主控截面140 master station 主站141 mechanical transmission MT 机械式变速箱142 mechanism 机构143 Metal Active Gas welding MAG 金属极（熔化极）活性性气体保护焊144 Metal Inert Gas welding MIG 金属极（熔化极）惰性气体保护焊145 MF Gun 中频焊枪146 MIG WELDING MIG焊147 modify 更改148 mounting plate 安装面149 multiple spot welding 多点焊N150 normalizing 正火151 nozzle 喷嘴O152 Off-line Programming OLP 离线编程153 ON-BOARD DIAGNOSTICS OBD 在线检测154 open 大开155 operating mechanism 操作机构156 orientation 方位157 over voltage relay 过电压继电器P158 pallet 物料架，小车托盘159 part drawing 零件图160 peak time 峰值时间161 performance characteristic 工作特性3 v1.0巨一自动化机器人事业部JEE Automation Robotics Division序号英文全称缩写中文全称备注162 pneumatic 气动163 pillar 立柱164 planning 规划165 position 位置166 postweld heat treatment/postheat treatment 焊后热处理167 PRESS 压力机168 Press Line 冲压线169 pressing robot 冲压机器人170 process 工序；工艺(强调过程）171 project 工程、项目、投影172 projection welding 凸焊173 property 属性Q174 quenching 淬火R175 rack 支架176 rail 轨道;横梁177 reachable 可达178 Reinforce glue 补强胶179 reinforcement 加强180 reliability 可靠性181 rigidity 刚度182 Regulator Interface Panel RIP 水气排183 robot programming language 机器人编程语言184 robot simulation 机器人仿真185 robot teaching 机器人示教S186 Sealer Pump 涂胶泵187 seam 接缝188 section 型材，断面189 semiopen小开190 sensor 传感器191 Servo Gun 伺服焊钳192 servo motor 伺服电机193 short-circuiting，bridge 短路194 shuttle 往复输送195 simulated interrupt 仿真中断196 spatter 飞溅197 Spot Welding Sealants 点焊密封胶198 spot welding; resistance spot welding 点焊199 stability 稳定性200 stand 换枪架201 station 工位202 strength 强度203 stud welding 植焊204 summary 摘要205 sun roof 天窗206 surface roughness 表面粗糙度T207 tapping 攻丝208 task 任务209 technique 工艺（强调技术手段）210 temperature control device 温度控制元件211 test signal 测试信号212 TIMER CONTROLLER T/C 焊接控制箱213 TIP 电极帽214 tip dresser 修磨器215 tip; contact tube 导电咀216 tool changer 换枪装置4 v1.0巨一自动化机器人事业部JEE Automation Robotics Division序号英文全称缩写中文全称备注217 torch 焊炬；弧焊焊枪218 touch screen；touch panel 触摸屏219 TRANSFORMER T/R 焊接变压器220 TROLLY 滑车221 Tungsten Inert Gas/Gas Tungsten Arc Welding TIG/GTAW 钨极（非熔化极）惰性气体保护焊；钨极氩弧焊222 TURN TABLE 回转台V223 valve 阀224 velocity transducer 速度传感器225 vertical 垂直226 virtual manufacturing 虚拟制造W227 washer 垫片228 wear and tear 磨损229 weldability焊接性230 welding current downslope time 焊接电流衰减时间231 welding cycle 焊接循环232 welding gun 焊枪233 welding machine; welder 焊机234 welding power source 焊接电源235 welding process 焊接工艺236 Welding Robot 焊接机器人237 welding spot 焊点238 welding technique 焊接技术239 wire cutting 电火花线切割X240 X Type Welding Gun X型焊枪5 v1.0巨一自动化机器人事业部JEE Automation Robotics Division序号英文全称缩写中文全称备注250 ASSEMBLY ASSY 总成BIW Abbr.251 BODY BUILD B/B 总成BIW Abbr.252 BODY COMPLETE B/C 总成BIW Abbr.253 BODY FLOOR B/F 地板BIW Abbr.254 BODY IN WHITE BIW 白车身BIW Abbr.255 BODY SIDE B/S 侧围BIW Abbr.256 BRACKET BRKT 支架BIW Abbr.257 CENTER CTR 中央通道BIW Abbr.258 COMPLETE COMPLT 组件；总成BIW Abbr. 259 DOOR DR 门BIW Abbr.260 ENGINE ENG 发动机BIW Abbr.261 EXTENTION EXTN 延伸BIW Abbr.262 FLOOR FLR 地板BIW Abbr.263 FRONT FR；FRT 前部BIW Abbr.264 HEAD LAMP H/LAMP 前大灯BIW Abbr.265 INNER INR 内部的BIW Abbr.266 LEFT HAND LH 左侧BIW Abbr.267 LOWER LWR 下部BIW Abbr.268 MEMBER MBR 纵梁BIW Abbr.269 OUTER OTR 外部BIW Abbr.270 PANEL PNL 面板BIW Abbr.271 RADIATOR RAD 水箱BIW Abbr.272 RADIATOR SUPPORT R/SUPT 水箱横梁BIW Abbr. 273 REAR RR 后部BIW Abbr.274 REINFORCEMENT REINF 加强BIW Abbr.275 RIGHT HAND RH 右侧BIW Abbr.276 ROOF RF 顶盖BIW Abbr.277 SIDE OUTER S/OTR 外侧BIW Abbr.278 SIDE SILL S/SILL 侧裙边BIW Abbr.279 SUB ASSEMBLY SUB ASSY 分总成BIW Abbr. 280 SUN ROOF S/RF 天窗BIW Abbr.281 SUPPORT SUPT 支撑BIW Abbr.282 UNDERBODY UB 地板BIW Abbr.283 UPPER UPR 上部BIW Abbr.284 intake pipe 进气管BIW285 fire wall，dash panel 前围板BIW286 rear wall 后围板BIW287 tailgate 后背板BIW288 fender 翼子板；挡泥板BIW289 fuel filler 加油口BIW290 front pillar,A-pillar A柱BIW291 center pillar,B-pillar B柱BIW292 rear pillar,C-pillar C柱BIW293 rail 横梁BIW294 hinge 铰链BIW295 guide rail 导轨BIW一级：169个（阴影）编制：欧智华日期：2009.04.156 v1.0__。