N089L6-L02 Ver 2[1].1 for Dell

TFT LCD Approval Specification MODEL NO.: N089L6 - L02O2008-09-19 11:48:05 CST PMMD IIIDirectorannie_hsu(®Zq/56522 /54873)Director Accept- CONTENTS -REVISION HISTORY ------------------------------------------------------- 31. GENERAL DESCRIPTION ------------------------------------------------------- 4 1.1 OVERVIEW1.2 FEATURES1.3 APPLICATION1.4 GENERAL SPECIFICATIONS1.5 MECHANICAL SPECIFICATIONS2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 5 2.1 ABSOLUTE RATINGS OF ENVIRONMENT2.2 ELECTRICAL ABSOLUTE RATINGS2.2.1 TFT LCD MODULE2.2.2 BACKLIGHT UNIT3. ELECTRICAL CHARACTERISTICS ------------------------------------------------------- 73.1 TFT LCD MODULE3.2 BACKLIGHT UNIT4. BLOCK DIAGRAM ------------------------------------------------------- 104.1 TFT LCD MODULE5. INPUT TERMINAL PIN ASSIGNMENT ------------------------------------------------------- 11 5.1 TFT LCD MODULE5.2 TIMING DIAGRAM OF LVDS INPUT SIGNAL5.3 COLOR DATA INPUT ASSIGNMENT5.4 EDID CODE DATA STRUCTURE6. CONVERTER SPECIFICATION ------------------------------------------------------- 186.1 ABSOLUTE MAXIMUM RATINGS6.2 RECOMMENDED OPERATING RATINGS7. INTERFACE TIMING ------------------------------------------------------- 197.1 INPUT SIGNAL TIMING SPECIFICATIONS7.2 POWER ON/OFF SEQUENCE8. OPTICAL CHARACTERISTICS ------------------------------------------------------- 21 8.1 TEST CONDITIONS8.2 OPTICAL SPECIFICATIONS9. PRECAUTIONS ------------------------------------------------------- 259.1 SYSTEM MATCHING PRECAUTIONS9.2 HANDLING PRECAUTIONS9.3 STORAGE PRECAUTIONS9.4 OPERATION PRECAUTIONS10. PACKING ------------------------------------------------------- 2610.1 CARTON10.2 PALLET11. DEFINITION OF LABELS ------------------------------------------------------- 2811.1 CMO MODULE LABEL11.2 CMO CARTON LABEL11.3 DELL CARTON LABELREVISION HISTORYVersion Date Page(New)Section DescriptionVer. 2.0 Ver. 2.1 Jul. 03, 2008Sep. 08,2008All2930All11.2drawingApproval specification first issued.Compal project code on CMO carton label is canceled.Adding protecting tape on corner of BLU FPC twist.1. GENERAL DESCRIPTION1.1 OVERVIEWN089L6 - L02 is a 8.9” TFT Liquid Crystal Display module with LED Backlight unit and 40 pins LVDSinterface. This module supports 1024 x 600 Wide-SVGA mode and can display 262,144 colors. Theoptimum viewing angle is at 6 o’clock direction. The converter module for Backlight is built in.1.2 FEATURES- WSVGA (1024 x 600 pixels) resolution- DE only mode- 3.3V LVDS (Low Voltage Differential Signaling) interface with 1 pixel/clock- Build in LED Converter1.3 APPLICATION- TFT LCD Notebook1.4 GENERAL SPECIFICATI0NSNoteUnit Item SpecificationActive Area 195.072(H) x 113.4(V) mm(1)Bezel Opening Area 198.27(H) x 116.6(V) mmDriver Element a-si TFT active matrix - -Pixel Number 1024 x R.G.B. x 600 pixel -Pixel Pitch 0.1905(H) X 0.189(V) mm -Pixel Arrangement RGB vertical stripe - -Display Colors 262,144 color -Transmissive Mode Normally white - -Surface Treatment Hard coating (3H), Glare Type - -1.5 MECHANICAL SPECIFICATIONSUnitMax.NoteTyp.Item Min.Horizontal (H) 213.06 213.36 213.66 mmModule Size(1)Vertical (V) 129.25 129.55 129.85 mmDepth (D) --- 5.15 5.45 mm-g185200Weight ---Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.2. ABSOLUTE MAXIMUM RATINGS2.1 ABSOLUTE RATINGS OF ENVIRONMENTValueItem SymbolMin. Max.Unit NoteStorage TemperatureT ST -20 +60 ºC (1) Operating Ambient Temperature T OP 0 +50 ºC (1), (2) Shock (Non-Operating) S NOP - 220/2 G/ms (3), (5)Vibration (Non-Operating)V NOP - 1.5 G (4),(5)Note (1) (a) 90 %RH Max. (Ta 40 ºC).(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).(c) No condensation.Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max.Note (3) 1 time for ± X, ± Y , ± Z. for Condition (220G / 2ms) is half Sine Wave,. Note (4) 10 ~ 500 Hz, 30 min/cycle,1cycles for each X, Y, Z axis.Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigidenough so that the module would not be twisted or bent by the fixture. The fixing condition is shown as below:2.2 ELECTRICAL ABSOLUTE RATINGS2.2.1 TFT LCD MODULEValueItem SymbolMin. Max.Unit Note Power Supply Voltage V CC -0.3 +4.0 VLogic Input Voltage V IN -0.3 V CC+0.3 VLED Converter Enable ENA 0 5 VLED BLU Brightness Control ADJ 0 5 V(1)Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions.2.2.2 BACKLIGHT UNITValueItem SymbolMin. Max.Unit Note LED Light Bar Power SupplyVoltageV L 0 30.6 VLED Light Bar Power Supply Current I L 0 55.5 mA(1), (2)Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions.Note (2) Specified values are for LED (Refer to 3.2 for further information).3. ELECTRICAL CHARACTERISTICS3.1 TFT LCD MODULE Ta = 25 ± 2 ºCValueParameter SymbolMin. Typ. Max.Unit NotePower Supply Voltage VCC 3.0 3.3 3.6 V - Ripple Voltage V RP - 50 - mV - Rush Current I RUSH - - 1.5 A (2) Initial Stage Current I IS - - 1.0 A (2)White - 150 162 mA (3)aPower Supply Current Black Lcc- 198 212 mA (3)bLVDS Differential Input High Threshold V TH(LVDS)- - +100 mV(5),V CM =1.2VLVDS Differential Input Low Threshold V TL(LVDS)-100 - - mV(5)V CM =1.2VLVDS Common Mode Voltage V CM 1.125 - 1.375 V (5) LVDS Differential Input Voltage |V ID | 100 - 600 mV (5) Terminating Resistor R T - 100 - Ohm - Power per EBL WG P EBL - 1.02 - W (4) Note (1) The ambient temperature is Ta = 25 ± 2 ºC. Note (2) I RUSH : the maximum current when VCC is rising I IS : the maximum current of the first 100ms after power-onMeasurement Conditions: Shown as the following figure. Test pattern: black.SWVcc+3.3VNote (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, f v = 60 Hz, whereas a power dissipation check pattern below is displayed.Note (4) The specified power are the sum of LCD panel electronics input power and the inverter input power. Test conditions are as follows.(a) Vcc = 3.3 V, Ta = 25 ± 2 ºC, f v = 60 Hz,(b) The pattern used is a black and white 32 x 36 checkerboard, slide #100 from the VESA file“Flat Panel Display Monitor Setup Patterns”, FPDMSU.ppt.(c) Luminance: 60 nits.Active Areaa. White PatternActive Areab. Black PatternVcc rising time is 470usNote (5) The parameters of LVDS signals are defined as the following figures.3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºCValueParameter Symbol Min. Typ. Max.Unit NoteLED Quantity 27 PCs (1) LED Light Bar PowerSupply VoltageV L 26.1 28.8 30.6 VLED Light Bar PowerSupply CurrentIL - 48 - mA(1),(2) (Duty 100%)Power Consumption P L - 1.382 - W (3), (Duty 100%) LED Life TimeL BL 15000 - - Hrs (4) Note (1) LED light bar configuration is shown as below.Note (2) For better LED light bar driving quality, it is recommended to utilize the adaptive boost converter with currentbalancing function to drive LED light-bar.Note (3) P L = I L V LNote (4) The lifetime of LED is defined as the time when it continues to operate under the conditions at Ta = 25 2 o C and I L = 16.0 mA(Per EA) until the brightness becomes 50% of its original value.0V V CM|Single Ended0V |V TH(LVDS)V TL(LVDS)DifferentialV I Channels4. BLOCK DIAGRAM 4.1 TFT LCD MODULE5. INPUT TERMINAL PIN ASSIGNMENT5.1 TFT LCD MODULEPin Symbol Description PolarityRemark1 GND Ground2 VCC Power Supply (+3.3V typ.)3 VCC Power Supply (+3.3V typ.)4 V EDID EDID power (+3.3V typ.)5 NCNo Connection (Reserved for CMOtest)6 CLK EDID EDID clock7 DATA EDID EDID data8 Rxin0- LVDS Differential Data Input Negative9 Rxin0+ LVDS Differential Data Input PositiveR0~R5,G010 GND Ground 11 Rxin1- LVDS Differential Data Input Negative12 Rxin1+ LVDS Differential Data Input PositiveG1~G5,B0,B113 GND Ground 14 Rxin2- LVDS Differential Data Input Negative15 Rxin2+ LVDS Differential Data Input PositiveB2~B5,DE,Hsync,Vsync16 GND Ground 17 CLK- LVDS Clock Data Input Negative18 CLK+ LVDS Clock Data Input PositiveLVDS Level Clock19 GND Ground 20 NC No Connection21 NC No Connection22 GND Ground 23 NC No Connection 24 NC No Connection 25 GND Ground 26 NC No Connection 27 NC No Connection 28 GND Ground 29 VLED LED Converter Input Power30 VLED LED Converter Input PowerLED Power Input31 LED_GND LED Ground 32 LED_GND LED Ground 33 LED_GND LED Ground 34 NC No Connection 35 NC No Connection 36 NC No Connection 37 NC No Connection 38 ADJ LED BLU Brightness Control (PWM) (3) 39 NC No Connection 40 NC No ConnectionNote (1) Connector Part No.: I-PEX 20347-340E-12 or equivalent Note (2) User’s connector Part No: I-PEX 20345-040T-31 or equivalent Note (3) BLU brightness is proportion to the duty of ADJ signal. Note (4) The first pixel is odd as shown in the following figure.5.2 TIMING DIAGRAM OF LVDS INPUT SIGNALRxin0 Rxin1 Rxin2 CLK+5.3 COLOR DATA INPUT ASSIGNMENTThe brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input forthe color. The higher the binary input, the brighter the color. The table below provides the assignment ofcolor versus data input.Data SignalRed Green Blue ColorR5R4 R3 R2R1R0G5G4G3G2G1G0B5 B4 B3 B2B1B0Basic Colors BlackRedGreenBlueCyanMagentaYellowWhite111111111111111111111111111111111111111111111111111111111111111111111111Gray Scale Of Red Red(0)/DarkRed(1)Red(2)::Red(61)Red(62)Red(63)::111::111::111::1111::111::11::::::::::::::::::::::::Gray Scale Of Green Green(0)/DarkGreen(1)Green(2)::Green(61)Green(62)Green(63)::::::::::::::111::111::111::1111::111::11::::::::::::Gray Scale Of Blue Blue(0)/DarkBlue(1)Blue(2)::Blue(61)Blue(62)Blue(63)::::::::::::::::::::::::::111::111::111::1111::111::11Note (1) 0: Low Level Voltage, 1: High Level Voltage5.4 EDID DATA STRUCTUREThe EDID (Extended Display Identification Data) data formats are to support displays as defined in the VESA Plug & Display and FPDI standards.Byte # (decimal) Byte #(hex)Field Name and CommentsValue(hex)Value(binary)0 0Header 0000000000 1 1Header FF11111111 2 2Header FF11111111 3 3Header FF11111111 4 4Header FF11111111 5 5Header FF11111111 6 6Header FF11111111 7 7Header 00000000008 8 EISA ID manufacturer name (“CMO”) 0D 000011019 9 EISA ID manufacturer name (Compressed ASCII) AF 1010111110 0A ID product code (N089L6-L02) 09 0000100111 0B ID product code (hex LSB first; N089L6-L02) 02 0000001012 0C ID S/N (fixed “0”) 00 0000000013 0D ID S/N (fixed “0”) 00 0000000014 0E ID S/N (fixed “0”) 00 0000000015 0F ID S/N (fixed “0”) 00 0000000016 10 Week of manufacture 1F 0001111117 11 Year of manufacture 12 0001001018 12 EDID structure version # (“1”) 01 0000000119 13 EDID revision # (“3”) 03 0000001120 14 Video I/P definition (“Digital”) 90 1001000021 15 Active area horizontal 21.3cm 15 0001010122 16 Active area vertical 12.9cm 0C 0000110023 17 Display Gamma (Gamma = ”2.2”) 78 0111100024 18 Feature support (“Active off, RGB Color”) 0A 0000101025 19 Rx1, Rx0, Ry1, Ry0, Gx1, Gx0, Gy1, Gy0 B9 1011100126 1A Bx1, Bx0, By1, By0, Wx1, Wx0, Wy1, Wy0 85 1000010127 1BRx=0.584 95 10010101 28 1CRy=0.362 5C 01011100 29 1DGx=0.350 59 01011001 30 1EGy=0.583 95 10010101 31 1FBx=0.154 27 00100111 32 20By=0.105 1B 00011011 33 21Wx=0.313 50 01010000 34 22Wy=0.329 54 0101010035 23 Established timings 1 (1024*600@60Hz) 00 0000000036 24 Established timings 2 (1024*600@40Hz) 00 0000000037 25 Manufacturer’s reserved timings 00 0000000038 26 Standard timing ID # 1 01 0000000139 27 Standard timing ID # 1 01 0000000140 28 Standard timing ID # 2 01 0000000141 29 Standard timing ID # 2 01 00000001Byte # (decimal) Byte #(hex)Field Name and CommentsValue (hex) Value (binary) 42 2A Standard timing ID # 3 01 0000000143 2B Standard timing ID # 3 01 0000000144 2C Standard timing ID # 4 01 0000000145 2D Standard timing ID # 4 01 0000000146 2E Standard timing ID # 5 01 0000000147 2F Standard timing ID # 5 01 0000000148 30 Standard timing ID # 6 01 0000000149 31 Standard timing ID # 6 01 0000000150 32 Standard timing ID # 7 01 0000000151 33 Standard timing ID # 7 01 0000000152 34 Standard timing ID # 8 01 0000000153 35 Standard timing ID # 8 01 0000000154 36 Detailed timing description # 1 60Hz Timing Pixel clock(“50.83MHz”, According to VESA CVT Rev1.1)DB 1101101155 37 # 1 60Hz Timing Pixel clock (hex LSB first) 13 0001001156 38 # 1 60Hz Timing H active (“1024”) 00 0000000057 39 # 1 60Hz Timing H blank (“296”) 28 0010100058 3A # 1 60Hz Timing H active : H blank (“1024 : 296”) 41 010******* 3B # 1 60Hz Timing V active (”600”) 58 010******* 3C # 1 60Hz Timing V blank (”42”) 2A 0010101061 3D # 1 60Hz Timing V active : V blank (”600 :42”) 20 0010000062 3E # 1 60Hz Timing H sync offset (81”) 51 010******* 3F # 1 60Hz Timing H sync pulse width ("54”) 36 0011011064 40 # 1 60Hz Timing V sync offset : V sync pulse width (”5 : 7”) 57 0101011165 41 # 1 60Hz Timing H sync offset :H sync pulse width : V sync offset :V sync width (”81: 54 : 5 : 7”)00 0000000066 42 # 1 60Hz Timing H image size (”195 mm”) C3 1100001167 43 # 1 60Hz Timing V image size (”113 mm”) 71 0111000168 44 # 1 60Hz Timing H image size : V image size (”193 : 115”) 00 0000000069 45 # 1 60Hz Timing H boarder (”0”) 00 0000000070 46 # 1 60Hz Timing V boarder (”0”) 00 0000000071 47 # 1 60Hz Timing Non-interlaced ; Normal display, no stereo ; DigitalSeparate ; V sync POL is negative ; H sync POL is positive1A 0001101072 48 Detailed timing description # 2 40Hz Timing Pixel clock(“33.89MHz”, According to VESA CVT Rev1.1)3D 0011110173 49 # 2 40Hz Timing Pixel clock (hex LSB first) 0D 0000110174 4A # 2 40Hz Timing H active (“1024”) 00 0000000075 4B # 2 40Hz Timing H blank (“296”) 28 0010100076 4C # 2 40Hz Timing H active : H blank (“1024 : 296”) 41 010******* 4D # 2 40Hz Timing V active (”600”) 58 010******* 4E # 2 40Hz Timing V blank (”42”) 2A 0010101079 4F # 2 40Hz Timing V active : V blank (”600 :42”) 20 0010000080 50 # 2 40Hz Timing H sync offset (”81”) 51 010******* 51 # 2 40Hz Timing H sync pulse width ("54”) 36 0011011082 52 # 2 40Hz Timing V sync offset : V sync pulse width (”5 : 7”) 57 0101011183 53 # 2 40Hz TimingH sync offset : H sync pulse width : V sync offset :V sync width (”81: 54 : 5 : 7”)00 00000000Byte # (decimal) Byte #(hex) Field Name and CommentsValue (hex) Value (binary) 84 54 # 2 40Hz Timing H image size (”195 mm”) C3 1100001185 55 # 2 40Hz Timing V image size (”113 mm”) 71 0111000186 56 # 2 40Hz Timing H image size : V image size (”195 : 113”) 00 0000000087 57 # 2 40Hz Timing H boarder (”0”) 00 0000000088 58 # 2 40Hz Timing V boarder (”0”)00 0000000089 59# 2 40Hz Timing Non-interlaced ; Normal display, no stereo ; DigitalSeparate ; V sync POL is negative ; H sync POL is positive1A 0001101090 5A Detailed timing description # 3 00 0000000091 5B # 3 Flag 00 0000000092 5C # 3 Reserved 00 0000000093 5D # 3 FE (hex) defines ASCII string (Model Name “N089L6”, ASCII) FE 1111111094 5E # 3 Flag 00 0000000095 5F # Dell P/N " K862H" 1st character (“K”) 4B 010******* 60 # Dell P/N " K862H" 2nd character (“8”) 38 0011100097 61 # Dell P/N " K862H" 3rd character (“6”) 36 0011011098 62 # Dell P/N " K862H" 4th character (“2”) 32 0011001099 63 # Dell P/N " K862H" 5th character (“H”) 48 010******** 64 LCD Supplier EEDID Revision #: "1" (MP Stage) 81 10000001101 65 Manufacturer P/N ( "N") 4E 010******** 66 Manufacturer P/N ( "0" ) 30 00110000103 67 Manufacturer P/N ( "8" ) 38 00111000104 68 Manufacturer P/N ( "9" ) 39 00111001105 69 Manufacturer P/N ( "L" ) 4C 010******** 6A Manufacturer P/N ( "6" )3600110110107 6BManufacturer P/N (If <13 char, then terminate with ASCII code 0Ah,set remaining char = 20h)0A 00001010108 6C Flag 00 00000000109 6D Flag 00 00000000110 6E Flag 00 00000000111 6F Data Type Tag: 00 00000000112 70 Flag 00 00000000113 71 SMBUS value @ 10 [cd/m2]=00 00 00000000114 72 SMBUS value @ 17 [cd/m2]=00 00 00000000115 73 SMBUS value @24 [cd/m2]=00 00 00000000116 74 SMBUS value @ 30 [cd/m2]=00 00 00000000117 75 SMBUS value @ 60 [cd/m2]=00 00 00000000118 76 SMBUS value @ 100 [cd/m2]=00 00 00000000119 77 SMBUS value @ 140[cd/m2]=00 00 00000000120 78 SMBUS value @ 180 [cd/m2]=0000 00000000121 79 Bit[1:0] 00:reserved , 01: single LVDS, 10: dual LVDS, 11: reservedBit[2] 0: No RTC support , 1: RTC supportBit[7:3] Reserved01 00000001122 7A BIST Enable: Yes = '01' No = '00' ("Yes")0100000001123 7B(If <13 char, then terminate with ASCII code 0Ah, set remainingchar = 20h)0A 00001010124 7C(If <13 char, then terminate with ASCII code 0Ah, set remainingchar = 20h)20 00100000Byte # (decimal) Byte # (hex)Field Name and CommentsValue (hex)Value (binary)125 7D(If <13 char, then terminate with ASCII code 0Ah, set remainingchar = 20h)20 00100000126 7E Extension flag 00 00000000127 7F Checksum A5 101001016. CONVERTER SPECIFICATION6.1 ABSOLUTE MAXIMUM RATINGSSymbol Ratings Vin 6.0V Gnd +/-0.3V ADJ -0.3V~6.0V6.2 RECOMMENDED OPERATING RATINGSValueParameter SymbolMin. Typ. Max.Unit NoteConverter Input power supply voltage V in 4.5 5.0 5.5 VADJ High Level 2.0 --- 5.0 VADJ Control Level ADJ Low Level0 --- 0.5 VADJ Control Duty Ratio 20 100 % ADJ Control Frequency f PWM 190 210 230 HzVin=4.5V 433 524 mA (1)Converter Input Current Vin=5.5V I BL354 429 mA (2) Note (1) The specified LED power supply current is under the conditions at Vin = 4.5V, Ta = 25 ± 2 ºC, f PWM= 200 Hz, Duty=100%.Note (2) The specified LED power supply current is under the conditions at Vin = 5.5V, Ta = 25 ± 2 ºC, f PWM= 200 Hz, Duty=100%.7. INTERFACE TIMING7.1 INPUT SIGNAL TIMING SPECIFICATIONSThe input signal timing specifications are shown as the following table and timing diagram.Signal Item Symbol Min. Typ. Max. Unit Note DCLK Frequency 1/Tc 40.5 45 47.25 MHz -Vertical Total Time TV 610 625 800 TH - Vertical Active Display Period TVD 600 600 600 TH- Vertical Active Blanking Period TVB TV-TVD 25 TV-TVD THHorizontal Total Time TH 110012001400 Tc (2) Horizontal Active Display Period THD 102410241024 Tc (2)DEHorizontal Active Blanking Period THB TH-THD 176 TH-THD Tc (2) Note (1) Because this module is operated by DE only mode, Hsync and Vsync are ignored.(2) 1 channel LVDS input.INPUT SIGNAL TIMING DIAGRAMDCLKDEDE DATA7.2 POWER ON/OFF SEQUENCETiming Specifications:0.5 ¡t1 10 ms 0 t2 50 ms 0 t3 50 ms t4 ¡ 500 ms t5 ¡ 200 ms t6 ¡ 200 msNote (1) Please follow the power on/off sequence described above. Otherwise, the LCD module might bedamaged.Note (2) Please avoid floating state of interface signal at invalid period. When the interface signal is invalid, besure to pull down the power supply of LCD Vcc to 0 V.Note (3) The Backlight converter power must be turned on after the power supply for the logic and theinterface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid.Note (4) Sometimes some slight noise shows when LCD is turned off (even backlight is already off). To avoidthis phenomenon, we suggest that the Vcc falling time is better to follow 50us t710 ms.- Power Supplyfor LCD, Vcc- LVDS Interface- Power for Lamp RestartPower OnPower Off0V0V8. OPTICAL CHARACTERISTICS8.1 TEST CONDITIONS Item Symbol Value UnitAmbient Temperature Ta 25±2 o CAmbient Humidity Ha 50±10 %RH Supply Voltage V CC 3.3 V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"LED Light Bar Input Current I L 52.5 mAThe measurement methods of optical characteristics are shown in Section 8.2. The following items should be measured under the test conditions described in Section 8.1 and stable environment shown in Note (5).8.2 OPTICAL SPECIFICATIONSThe relative measurement methods of optical characteristics are shown in 8.2. The following itemsshould be measured under the test conditions described in 8.1 and stable environment shown in Note (5). ItemSymbol Condition Min. Typ. Max. Unit Note Contrast RatioCR 300 400 - - (2), (5)T R - 3 8 ms Response TimeT F - 7 12 ms (3) Average Luminance of WhiteL 5p 180 200 - cd/m 2(4), (5)Luminance Non-UniformityδW 5p - - 1.25 (5), (6)Rx 0.571 - RedRy 0.360 - Gx 0.351 - Green Gy 0.573 - Bx 0.156 - BlueBy 0.118- Wx 0.313 - ColorChromaticity WhiteWy θx =0°, θY =0° Viewing Normal Angle TYP -0.050.329 TYP +0.05 - θx + 40 45 - Horizontalθx - 40 45 - θY + 20 20 - Viewing AngleVerticalθY -CR ≥10 40 45 - Deg. (1), (5)Note (1) Definition of Viewing Angle (θx, θy):Note (2) Definition of Contrast Ratio (CR):The contrast ratio can be calculated by the following expression.Contrast Ratio (CR) = L63 / L0L63: Luminance of gray level 63L 0: Luminance of gray level 0CR = CR (1)CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (T R, T F):100%90%Optical10%0%Note (4) Definition of Average Luminance of White (L AVE):Measure the luminance of gray level 63 at 5 pointsL AVE = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5L (x) is corresponding to the luminance of the point X at Figure in Note (6)Note (5) Measurement Setup:The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room.Note (6) Definition of White Variation (δW):Measure the luminance of gray level 63 at 5 pointsδW = { Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]Active AreaV e r t i c a l L i n e Horizontal Line : Test Point X=1 to 59. PRECAUTIONS9.1 SYSTEM MATCHING PRECAUTIONS(1) Refer to the drawing.(2) To avoid wireless noise interference, please keep the antenna away from LCD control board.9.2 HANDLING PRECAUTIONS(1) The module should be assembled into the system firmly by using every mounting hole. Be careful notto twist or bend the module.(2) While assembling or installing modules, it can only be in the clean area. The dust and oil may causeelectrical short or damage the polarizer.(3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection andassembly process.(4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer isvery soft and easily scratched.(5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not useKetone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might permanently damage the polarizer due to chemical reaction.(6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel fora long time.(7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. Incase of contacting with hands, legs or clothes, it must be washed away thoroughly with soap.(8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC.(9) Do not disassemble the module.(10) Do not pull or fold the lamp wire.(11) Pins of I/F connector should not be touched directly with bare hands.9.3 STORAGE PRECAUTIONS(1) High temperature or humidity may reduce the performance of module. Please store LCD module withinthe specified storage conditions.(2) It is dangerous that moisture come into or contacted the LCD module, because the moisture maydamage LCD module when it is operating.(3) It may reduce the display quality if the ambient temperature is lower than 10 ºC. For example, theresponse time will become slowly, and the starting voltage of lamp will be higher than the room temperature.9.4 OPERATION PRECAUTIONS(1) Do not pull the I/F connector in or out while the module is operating.(2) Always follow the correct power on/off sequence when LCD module is connecting and operating. Thiscan prevent the CMOS LSI chips from damage during latch-up.(3) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock whileassembling with inverter. Do not disassemble the module or insert anything into the Backlight unit.9.5 OTHER PRECAUTIONS(1) When fixed patterns are displayed for a long time, remnant image is likely to occur.10. PACKINGCARTON10.110.2 PALLETFigure. 10-2 Packing method11. DEFINITION OF LABELS11.1 CMO MODULE LABELThe barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.(a) Model Name: N089L6 - L02(b)Revision: Rev. XX, for example: A1, …, C1, C2 …etc. (c)(d) Production Location: MADE IN XXXX. XXXX stands for production location.Serial ID includes the information as below:(a) Manufactured Date: Year: 1~9, for 2001~2009Month: 1~9, A~C, for Jan. ~ Dec.Day: 1~9, A~Y , for 1st to 31st , exclude I , O and U(b) Revision Code: cover all the change(c) Serial No.: Manufacturing sequence of productYear, Month, Date CMO Internal Use Revision Serial No. CMO Internal Use CMO Internal UseN089L6-L02Lead freeXXXXX。