CH-805卡车耐磨衬里

组装、冲压、喷漆等专业词汇Layout布置图fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码fuse together熔合fuse machine热熔机repair修理cosmetic inspect外观检查inner parts inspect内部检查EMI gasket导电条front plate前板rear plate后板chassis基座bezel panel面板sheet metal parts 冲件trolley台车carton纸箱punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机to move, to carry, to handle搬运pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具buzzle蜂鸣器defective product label不良标签identifying sheet list标示单pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) with exposed fingers割手套band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprisedie worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料? spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine ?孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂?床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规。

科技与创新┃Science and Technology&Innovation ·172·2021年第15期文章编号：2095－6835（2021）15－0172－03大秦线C80型货车转向架卡入式滑槽磨耗板一系列故障及防控措施田振国（大秦铁路有限公司湖东车辆段，山西大同037005）摘要：针对目前大秦线重载C80系列万吨、两万吨货物列车转向架装用的卡入式滑槽磨耗板存在的一些常见问题进行深入细致的分析和研究，并找到一些故障的防控措施和办法。

关键词：转向架；卡入式滑槽磨耗板；常见故障；防控措施中图分类号：U279文献标志码：A DOI：10.15913/ki.kjycx.2021.15.0771概述大秦线是全国重载第一线，政治意义和经济意义十分重要，关系着整个太原铁路局。

大秦线铁路货物列车主要以C80系列敞车为主，C80敞车分为不锈钢C80B（H）和铝合金C80（H）两种车型。

随着万吨、两万吨列车的多年运行，一些车辆故障也随之暴露出来。

转向架是车辆负责走行的装置，铸钢侧架是转向架组成的主要部件之一，卡入式滑槽磨耗板是装用在侧架上的钢质基础制动系统的一个磨耗件，方便于更换，可降低侧架滑槽磨损的焊修次数，保证制动梁端部的滑块能在其内正常滑动并减少其磨耗。

通过滑槽磨耗板把侧架滑槽与制动梁滑块磨耗套的滑动接触，变为滑槽磨耗板与制动梁滑块磨耗套的滑动接触，将制动梁的闸瓦与车轮踏面抱紧和分开，实现车辆的正常制动和缓解作用。

各种卡入式滑槽磨耗板故障势必影响到车辆的制动作用，会对车辆行车安全造成一定影响。

一些不明原因的制动缓解不良与滑槽磨耗板的卡滞故障有直接的关系，如果卡入式滑槽磨耗板在运用中发生反装、错装、松动、窜出、裂损，极易造成制动梁在其槽内滑动受阻，一是引发滑槽磨耗板向后滑动造成卡入式滑槽磨耗板卡在枕簧上，出现制动梁在缓解时不易回位，始终保持在制动状态下而造成车辆制动，二是会给车辆运行安全带来重大隐患。

C80技术资料C80、C80B新技术学习资料1、车辆用途C80型铝合金运煤敞车是供大秦线2万吨重载列车运输煤炭用的专用敞车。

该车能与秦皇岛煤码头的三、四期翻车机及附属设备相匹配，实现不摘钩连续翻卸作业；并能适应环形装车、直进直出装车、解体装车作业及运行时机车动力集中牵引要求。

2、主要性能参数载重(t) 80自重(t) ≤20总重(t) 100轴重(t) 25自重系数 0.25每延米重(t/m) 8.33容积(m3) 87比容(m3/t) 1.09车辆通过最小曲线半径(m) 145商业运营速度(km/h) 100制动距离(重车、紧急，m) 电空制动≤1400空气制动≤1600 限界：符合GB146.1-1983《标准轨距铁路机车车辆限界》的要求。

3、主要尺寸单辆车长度(mm) 12000三辆车长度(采用牵引杆、mm) 36000车辆定距(mm) 8200车辆最大高度(mm) 3793车辆最大宽度(mm) 3184车体内长(mm) 10728车体内宽(mm) 2946浴盆底面距轨面高(空车、mm) 267车钩中心线高(mm) 880车轮直径(mm) 8404、车辆主要特点1.2.1 采用双浴盆结构，车体除底架外采用铝合金型材与板材的铆接结构，车体自重轻，容积大，载重达80t；同时铝合金材料耐腐蚀性强，延长了车辆检修周期及使用寿命。

1.2.2 车辆结构按2万吨列车的考核标准进行设计，底架中梁采用屈服强度为450MPa的高强度耐候钢，并对牵引梁部分进行了加强。

1.2.3 车辆外形尺寸满足秦皇岛三、四期翻车机及其附属设施的匹配要求，可以实现不摘钩连续翻卸作业。

1.2.4 制动装置采用制动主管压力能满足500Kpa和600Kpa的空气制动装置，同时预留ECP 有线电空制动系统安装位置。

1.2.5 转向架采用转K6型转向架或转K5型转向架，具有运行速度高、动力学性能稳定等特点。

5、车体1.5.1.1 车体结构该车车体为双浴盆式、铝合金铆接结构，主要由底架、浴盆、侧墙、端墙和撑杆等组成（见图1.3）。

大秦线C80型货车17号车钩裂纹原因分析及应对措施1 大秦线货车运用现状C80 型货车是齐齐哈尔车辆厂为大秦线设计、生产的运煤专用车，自2002年正式上线运行。

钩缓装置采用的是国产化的E级钢联锁式转动车钩和固定车钩（17号车钩），在车钩的强度及抗疲劳方面较转13A型有较大提高，为提高C80车的运行安全起到了关键性的作用，但随着大秦线提速、重载增运要求17号车钩发生裂纹故障机率逐渐增多，在一定程度上已成为行车安全隐患。

在大秦线运用货车中，17 号车钩的装车辆数比例占到85%以上。

因此，对17号车钩裂纹出现的新动向进行调查、分析势在必行。

2 车钩配件裂纹情况调查2006年，段修中发现C80型敞车装用的17号钩体、钩舌裂纹比例分别为64.6%，而2007年检修中，钩体、钩舌裂纹所占比例已上升到65.3%。

车钩裂纹部位在钩尾销孔和钩耳孔处，尾销孔裂纹全部在销孔后部内侧面，裂纹走向与销孔轴线平行，最长裂纹达到45mm。

钩耳孔裂纹多数在下钩耳孔护销处，最长裂纹15mm。

钩体裂纹多数伴有铸造缺陷。

钩舌裂纹部位全部在钩舌内侧面上下弯角及中内处，裂纹最长达40mm。

近期，在进行C80型敞车临修时，又连续发现5件钩舌裂纹故障，其中有3件是经过检修后运行时间均不足1年半出现的裂纹，从17型钩舌在新造装车后第1个段修（全面检查修）期内已有超过60%裂纹的情况来看，绝大部分都将在装车使用4年（2个段修期）内产生裂纹，而在车钩连挂状态下，钩舌裂纹均为非可视部位，列检等部门很难发现。

3 裂纹形成原因分析3.1 大秦线运用车辆受力工况大秦线C80型车在1个定检期内所走行里程是其它线路上车辆走行里程的2倍。

在大秦线长大坡道多、曲线多的运行条件下，C80车由于频繁使用和提速增载，车辆受力较大，钩缓配件的受力还增加了侧向力和扭转力，引起材质疲劳速度加快，再加上运行中不正常的冲撞、超偏载和装卸时碰撞等因素，从客观上增加了裂纹故障的发生率。

1 1 一、转向架部分TB/T35-1999 中心销450 Q235A2 2 QCZ133-00-01 承载鞍ZG230-4503 3 QCZ133-00-02A 心盘磨耗盘尼龙4 4 QCZ133-00-03 外圆弹簧(1) 60Si2CrVAT5 5 QCZ133-00-04 内圆弹簧60Si2CrVAT6 6 QCZ133-00-05 减振外圆弹簧60Si2CrVAT7 7 QCZ133-00-06 减振内圆弹簧60Si2CrVAT8 8 QCZ133-00-07 外圆弹簧(2) 60Si2CrVAT9 9 QCZ133-00-08A 挡键TB/T2942-B级10 10 QCZ133-00-09A 螺栓M16X95 16 8.8级11 11 QCZ103-00-05 调整垫 5 Q235A12 12 GB/T6170 螺母M16 8级13 13 GB/T93 垫圈16 65Mn14 14 GB/T870 半沉头铆钉6X24 BL215 15 QCZ133-20-00 侧架组成16 15.1 QCZ133-20-01 侧架B+级钢17 15.2 QCZ133-20-02 右支撑座Q235D18 15.3 QCZ133-20-03 左支撑座Q235D19 15.4 QCZ133-20-04 磨耗板45#20 15.5 QCZ85-20-05 保持环Q345A21 15.6 QCZ85-20A-02 左滑槽磨耗板T1022 15.7 QCZ85-20A-03 右滑槽磨耗板T1023 15.8 QCZ85A-20-02 折头螺栓20MnTiB24 15.9 GB/97.1 垫圈20 3 140HV25 15.10 GB/T889.1 螺母M20 10级26 16 QCZ133/4-40A-00 摇枕组成27 16.1 QCZ133-40-01 摇枕B+级钢28 16.2 QCZ75-40-02 下心盘ZG230-45029 16.3 QCZ133-40A-01 托板(1) 8 Q235A30 16.4 QCZ85-42-01 销轴22 Q235A31 16.5 QCZ85-42-03 滚套尼龙32 16.6 QCZ133-40A-02 托板(2) 8 Q235A33 16.7 QCZ85A-40-01 斜面磨耗板 6 0Cr18Ni934 16.8 GB/T31.1 螺栓M24X100 24 10.9级35 16.9 BY型防松螺母M24 10级36 16.10 GB/T7244 垫圈M24 24 65Mn37 16.11 GB/T91 销5X45 Q215A38 16.12 GB/T91 销 3.2X20 Q215A39 16.13 GB/T95 垫圈12 100HV40 16.14 QCZ133-41A-00 固定杠杆支点座组成(1)41 16.14.1 固定杠杆支点座(1) ZG230-45042 16.14.2 Q/QC35-096-2000 衬套28X38X25-BC 奥-贝球铁43 16.15 QCZ134-41A-00 固定杠杆支点座组成(2)44 16.15.1 固定杠杆支点座(2) ZG230-45045 16.15.2 Q/QC35-096-2000 衬套28X38X25-BC 奥-贝球铁46 17 QCZ133/4-50A-00 制动装置47 17.1 TB/T34 闸瓦销环低碳钢丝SZ-F-300-GB/T343-9448 17.2 TB/T33 闸瓦插销Q235A49 17.3 QCZ133-50A-01 链蹄环Q235A50 17.4 TB/T54 圆销36X85X75 4551 17.5 TB/T54 圆销28X75X67 4552 17.6 TB/T1167 扁孔圆销36X100X65 4553 17.7 QCZ133-50A-02 支点Q235A54 17.8 GB/T91 销8X80 Q215A55 17.9 GB/T91 销 6.3X60 Q215A56 17.10 TB/T780 扁开口销A6X20X75 Q215A.F57 17.11 QCZ133-50-01 中拉杆Q235A58 17.12 QCZ133-51-00 游动杠杆组成59 17.12.1 游动杠杆Q235A60 17.12.2 Q/QC35-96-2000 衬套36X46X25-BC 奥-贝球铁61 17.12.3 Q/QC35-96-2000 衬套28X38X25-BC 奥-贝球铁62 17.13 QCZ133-53-00 固定杠杆组成63 17.13.1 固定杠杆Q235A64 17.13.2 Q/QC35-96-2000 衬套36X46X25-BC 奥-贝球铁65 17.13.3 Q/QC35-96-2000 衬套28X38X25-BC 奥-贝球铁66 17.14 QCP704A-10/20-00 右(左）组合式制动梁67 17.14.1 QCP704A-10-01B 右闸瓦托TB/T2942-B级68 17.14.2 QCP704A-10-02B 左闸瓦托TB/T2942-B级69 17.14.3 QCP704-10-02 制动梁架Q460E70 17.14.4 QCP704-10-03 夹扣Q235A71 17.14.5 QCP704-10-05 右支柱Q235A72 17.14.6 QCP704-20-01 左支柱Q235A73 17.14.7 Q/QC35-096-2000 衬套36X46X18-BC 奥-贝球铁74 17.14.8 QCP704-10-08A 滑块磨耗套改性尼75 17.14.9 QCP704-10-09 制造标记牌OCr1376 17.14.10 QCP704A-10-11 制动梁安全链卡子2077 17.14.11 QCP704-11-00 制动梁安全链78 17.14.11.1 QCP704-11-01 长孔眼环螺栓Q235A79 17.14.11.2 QCP704-11-02 链环8X45 8 Q235-A80 17.14.11.4 QCZ3-36A-01 链蹄环Q235A81 17.14.11.5 QCZ3-36A-02 链环12X55 Q235A82 17.14.11.6 QCZ3-36A-03 链环12X45 Q235A83 17.14.11.7 Q/QC56-116-92 螺栓M16X65 4.8级84 17.14.11.8 GB/T41 螺母M16 5级85 17.14.11.9 GB/T95 垫圈16 100HV86 17.14.11.10 GB/T91 销4X40 Q235A87 17.14.11.11 TB/T897-1999 眼环螺栓M16X55 Q235A88 17.14.11.12 GB6172-86 螺母M16 04级89 17.14.11.13 GB/T95 垫圈16 100HV90 17.14.11.14 GB/T6172.1 螺母M16 04级91 17.14.12 GB/T863.2 铆钉12X38 BL392 17.14.13 GB/T5780 螺栓M16X110 4.8级93 17.14.14 GB/T41 螺母M16 5级94 17.14.15 GB/T93 垫圈M16 65Mn95 17.14.16 GB/T848 垫圈M16 140HV96 17.14.17 GB/T869 铆钉8X58 LF1097 17.14.18 哈克拉铆钉B0M-R16-1098 17.15 新型高磨合成闸瓦99 18 QCZ85A/86A-70-00 交叉支撑装置100 18.1 QCZ85-70-01 锁紧板Q235A101 18.2 QCZ85A-70-01 双耳垫圈Q235A102 18.3 QCZ85A-70-02 螺栓20MnTiB103 18.4 QCZ85A-70-04 标志板0Cr13104 18.5 GB/T5781 螺栓M12X40 4.8级105 18.6 GB/T41 螺母M12 4级106 18.7 GB/T95 垫圈12 100HV107 18.8 QCZ85A-71A-00 交叉杆组成108 18.8.1 QCZ85A-71A-01 交叉杆上扣板Q235A109 18.8.2 QCZ85A-71A-02 X型弹性垫聚酯弹110 18.8.3 QCZ85A-71A-03 U型弹性垫聚酯弹性体111 18.8.4 QCZ85A-71A-04 交叉杆下扣板Q235A112 18.8.5 QCZ85A-72A-00 上交叉杆113 18.8.5.1 QCZ105-71A-01 交叉杆端头Q345D114 18.8.5.2 QCZ85A-72-01 上交叉杆杆身CR-1 115 18.8.6 QCZ85A-73A-00 下交叉杆116 18.8.6.1 QCZ105-71A-01 交叉杆端头Q345D117 18.8.6.2 QCZ85A-71-02 下交叉杆杆身CR-1 118 18.9 QCZ85A-73-00 橡胶垫119 18.10 QCZ85A-74A-00 安全索120 18.10.1 QCZ85A-74A-01 安全索端头BL2 121 18.10.2 QCZ85A-74A-02 安全索接头6063-O122 18.10.3 安全索钢丝绳GB/T8918-1996 4ZBB6X19+IWS1770ZS123 19 QCZ83JX-80-00 JC型双作用弹性旁承124 19.1 QCZ83JX-81-00 JC型弹性旁承体组成125 19.1.1 QCZ83JX-82-00 JC型弹性旁承体126 19.1.2 QCZ83JX-81-01A 旁承磨耗板127 19.2 QCZ85-80A-01 调整垫板Q235A128 19.3 QCZ83JX-80-01 旁承座TB/T2942-B级129 19.4 QCZ83JX-80-02 滚子45130 19.5 QCZ83JX-80-03 滚子轴45131 19.6 QCZ85-80A-02 垫片Q235A132 19.7 QCZ83JX-80-04 垫板Q235A133 20 SKTD25C-00-00 轴箱橡胶垫134 21 QCZ133-90-00 组合式斜楔135 21.1 QCZ133-90-01 斜楔ADI136 21.2 QCZ129-30-12 垫圈Q235A137 21.3 QCZ133-90-02 主磨擦板高分子复合材料138 21.4 GB/T91 销5X70 Q235A139 22 QCZ133B-90-00 横跨梁总成140 22.1 QCZ133B-91-00 横跨梁托141 22.1.1 QCZ133B-91-01 横跨梁托座120X53X5.5 Q235A142 22.1.2 QCZ86A-91A-02 定位挡24X24 Q235A143 22.1.3 QCZ86A-91A-03 底板 6 Q235A144 22.2 QCZ86A-92B-00 横跨梁组成145 22.2.1 QCZ86A-92B-01 横跨梁50X30X3 Q235A146 22.2.2 QCZ86A-92A-03 垫板 6 Q235A 147 22.2.3 触板8 0Cr18Ni9-8X120X160148 22.2.4 QCZ86A-92B-02 套筒20 炉钢管光-20-GB/T3092-93-Q235A149 22.3 QCZ50A-40-010 横跨梁总成安全链150 22.3.1 TB/T897 眼环螺栓M16X55 Q235A 151 22.3.2 TB/T894 链环10X32 10 Q235A 152 22.3.3 HT32-01-91 吊座8 Q215A153 22.3.4 GB/T95 垫圈16 3 Q235A154 22.3.5 GB/T41 螺母M16 4级155 22.3.6 GB/T6172 螺母M16 04级156 22.4 QCZ86A-90A-01 调整板 5 Q235A.F 157 22.5 QCZ86A-90A-02 磨耗垫板尼龙158 22.6 QCZ50A-40-001 跨梁吊座63X63X8 Q235A159 22.7 Q/QC56-116-92 螺栓M20X100 20 4.8级160 22.8 GB/T91 销4X50 4X50 Q215A161 22.9 GB/T97.1 垫圈20 20 Q215A162 22.10 GB/T6179 螺母M20 M20 5级。

HEM750压裂车控制器用户手册HMU8-750显示模块HEM750主控模块郑州众智科技股份有限公司SMARTGEN (ZHENGZHOU) TECHNOLOGY CO.,LTD.目次前言 (4)1概述 (6)2性能特点 (7)2.1HMU8-750显示模块性能特点 (8)2.2HEM750主控模块性能特点 (8)3规格 (9)4显示与操作 (11)4.1显示模块前面板 (11)4.2显示界面与操作 (12)4.2.1主页显示 (12)4.2.2详细信息显示 (13)4.2.3报警显示 (14)4.2.4历史记录显示 (15)4.2.5关于显示 (16)4.3参数配置 (17)4.3.1显示模块参数配置 (17)4.3.2主控模块参数配置 (18)4.3.3高级参数配置 (20)4.4手动开停机操作 (20)4.4.1开机顺序 (20)4.4.2停机顺序 (20)4.5调速操作 (20)4.5.1CAN调速 (20)4.5.2GOV调速 (21)4.5.3继电器调速 (21)5保护 (22)5.1警告报警 (22)5.2停机报警 (26)5.3故障怠速报警 (31)5.4散热停机报警 (35)6接线 (40)6.1HMU8-750显示模块背面板 (40)6.2HEM750主控模块面板 (41)6.3显示模块和主控模块连接示意图 (44)7编程参数范围及定义 (44)7.1显示模块参数设置内容及范围 (44)7.2主控模块参数设置内容及范围 (46)7.3报警项目设置说明 (58)7.4可编程输出口1-10可定义内容 (58)7.4.1自定义时间段输出 (64)7.4.2自定义组合输出 (64)7.5开关量输入口1-9可定义内容 (65)7.6传感器选择 (67)7.7起动成功条件选择 (68)7.8维护设置 (68)8传感器设置 (69)9试运行 (70)10典型应用 (71)11安装 (72)11.1HMU8-750安装 (72)11.1.1卡件 (72)11.1.2外形及开孔尺寸 (72)11.2HEM750安装 (73)11.2.1螺钉及导轨安装方式 (73)11.2.2外形尺寸 (74)12控制器与发动机的J1939连接 (75)12.1CUMMINS ISB/ISBE(康明斯) (75)12.2CUMMINS QSL9 (75)12.3CUMMINS QSM11(进口) (75)12.4CUMMINS QSX15-CM570 (76)12.5CUMMINS GCS-MODBUS (76)12.6CUMMINS QSM11(西安康明斯) (77)12.7CUMMINS QSZ13(东风康明斯) (77)12.8DETROIT DIESEL DDEC III/IV(底特律) (77)12.9DEUTZ EMR2(道依茨) (77)12.10JOHN DEERE(强鹿) (78)12.11MTU MDEC (78)12.12MTU ADEC(SMART模块) (78)12.13MTU ADEC(SAM模块) (79)12.14PERKINS(珀金斯) (79)12.15SCANIA (79)12.16VOLVO EDC3(沃尔沃) (80)12.17VOLVO EDC4 (80)12.18VOLVO-EMS2 (80)12.19玉柴 (81)12.20潍柴 (81)13故障排除 (82)前言是众智的中文商标是众智的英文商标SmartGen ― Smart的意思是灵巧的、智能的、聪明的，Gen是generator(发电机组)的缩写，两个单词合起来的意思是让发电机组变得更加智能、更加人性化、更好的为人类服务！不经过本公司的允许，本文档的任何部分不能被复制(包括图片及图标)。