MDR快速安装指南

安装 Crucial 英睿达 SSD 很简单，可让您的电脑速度明显变快！3. 备份重要文件在开始实际安装之前，花几分钟时间将您电脑中所有的重要文件保存到外部存储硬盘或 USB硬盘中。

4. 逐步仔细安装此处包含您所需的全部信息。

您的系统可能与所示系统的外观不同， 但是安装过程相同。

仔细阅读每个步骤，并查看帮助提示，以获取更多信息。

帮助提示对于 Mac 安装，遵守我们的 Mac 指定 SSD 安装步骤，地址 /mac-ssd-install ，因为安装步骤 明显不同，因此不是所有的 Mac 系统都是可升级的。

1. 准备用品您将需要准备系统、螺丝刀、Crucial 英睿达固态硬盘、一根 SATA 转 USB 数据线，还有系统用户手册。

如果您没有 SATA 转 USB 数据线， 则您可以在 Crucial 英睿达 SSD 安装套件中获得，该安装套件单独销售。

2. 将衬垫放置一旁 将 SSD 从盒子里取出来，您将看到这个 - 我们叫它衬垫，有的型号的固态硬盘中没有衬垫。

现在将其放置一旁。

到安装过程后面才需要，而且根据您的系统，甚至可能都不需要用到。

旧硬盘数据容量复制到新 SSD 可能需要的时间少于 256GB 20-30 分钟256-512GB30-60 分钟512GB-1TB 60-90 分钟您是否知道……？SSD 安装过程用时颇久的是从旧硬盘将所有数据复制到新的 SSD 。

开始之前，请参考左边表格获悉所需时间。

3. 安装已下载的软件打开刚才下载的文件并接受所有提示，安装此软件。

您需要在弹出的屏幕上单击安装。

安装完成之后，启动 Acronis。

1. 将 SSD 连接到您的系统首先，使用 SATA 转 USB 数据线将 SSD 连接到电脑。

处理 SSD 时，避免手指触碰金色接头。

2. 下载将旧硬盘复制到新 SSD 的软件 现在开始下载可将旧存储硬盘复制到新 SSD 的软件。

在与 SSD 连接的电脑上，访问屏幕上显示的网站下载软件。

Quick Installation Guide ServeRAID M5100Series Battery Kit for IBM System xBefore using this information and the product it supports,read the Important Notices and Warranty Information documents that come with the ServeRAID M5100Series Battery Kit for IBM®System x®(referred to in this document as the battery unit).This Quick Installation Guide contains information about remotely mounting the battery unit in a server and connecting the battery unit to a transportable memory module.Statement1:DANGERElectrical current from power,telephone,and communication cables is hazardous.To avoid a shock hazard:v Do not connect or disconnect any cables or perform installation,maintenance,or reconfiguration of this product during an electrical storm.v Connect all power cords to a properly wired and grounded electrical outlet.v Connect to properly wired outlets any equipment that will be attached to this product.v When possible,use one hand only to connect or disconnect signal cables.v Never turn on any equipment when there is evidence of fire,water,or structural damage.v Disconnect the attached power cords,telecommunications systems,networks,and modems before you open the device covers,unless instructed otherwise in the installation and configurationprocedures.v Connect and disconnect cables as described in the following table when installing,moving,or opening covers on this product or attached devices.To Connect:To Disconnect:1.Turn everything OFF.2.First,attach all cables to devices.3.Attach signal cables to connectors.4.Attach power cords to outlet.5.Turn device ON.1.Turn everything OFF.2.First,remove power cords from outlet.3.Remove signal cables from connectors.4.Remove all cables from devices.Statement28:CAUTION:The battery is a lithium ion battery.To avoid possible explosion,do not burn the battery.Exchange it only with the IBM-approved part.Recycle or discard the battery as instructed by local regulations.In the United States,IBM has a process for collection of this battery.For information,call 1-800-426-4333.Have the IBM part number for the battery unit available when you call.Attention:The battery in the ServeRAID M5100series battery assembly must charge for at least six hours under normal operating conditions.To protect your data,the ServeRAID controller firmwarechanges the write policy to write-through until the battery unit is sufficiently charged.When the battery unit is charged,the ServeRAID controller firmware changes the write policy to write-back to take advantage of the performance benefits of data caching.The battery unit is an intelligent battery backup unit (iBBU)based on lithium ion (LiON)battery cell technology.The battery unit protects the integrity of the cached data on a ServeRAID M5100series controller for up to 48hours (depending on the derated retention time that is selected)in case of a complete ac power failure or a brief power outage.The battery unit is mounted inside a server and is connected by a 20-pin cable to a ServeRAID M5100Series 512MB Cache/RAID 5Upgrade for IBM System x (referred to in this document as thetransportable memory module).Option kit partsThe battery unit option kit contains the following parts:v One ServeRAID M5100Series Battery Kit for IBM System x0Li IonModel:BAT1S1P-A Front ViewRear Viewv Two remote-mount cables –One 50cm (19.7in.)20-pin remote-mount cable–One 95cm (37.4in.)20-pin remote-mount cable2v IBM ServeRAID M Documentation CDv IBM Warranty Information documentv IBM Important Notices documentHandling electronic devicesAttention:Static electricity can damage the server and other electronic devices.To avoid damage,keep an electronic device in its static-protective package until you are ready to install it.To reduce the possibility of damage from electrostatic discharge,observe the following precautions:v Limit your movement.Movement can cause static electricity to build up around you.v The use of a grounding system is recommended but is not required.For example,wear an electrostatic-discharge wrist strap,if one is available.v Handle the device carefully,holding it by its edges or its frame.v Do not touch solder joints,pins,or exposed circuitry.v Do not leave the device where others can handle and damage it.v While the device is still in its static-protective package,touch it to an unpainted metal part of the server for at least2seconds.This drains static electricity from the package and from your body.v If it is necessary to set down the device after you remove it from its static-protective package,put it back into the package.Do not place the device on the server cover or on a metal surface.v Take additional care when you handle the device during cold weather.Heating reduces indoor humidity and increases static electricity.Mounting the battery unit inside the serverAttention:To avoid the loss of data,back up your data before you change your system configuration.To mount the battery unit inside the server,complete the following steps:1.Read the safety information that comes with the server.2.Turn off the server and peripheral devices and disconnect the power cords.Remove the server cover.For more information,see the installation instructions that come with the server.3.In a static-free environment,carefully remove the battery unit from the antistatic bag and inspect it fordamage.If it appears to be damaged,contact your place of purchase.34.Mount the battery unit in a suitable location inside the server,observing the following guidelines:v There is no standard method for mounting the battery unit inside the server.The correct mounting location and procedure depends on the server configuration.v You must connect a remote-mount cable to the battery unit that is installed remotely in the server and to the transportable memory module that is mounted on the controller.Make sure that one of the remote-mount cables that come with the battery unit is long enough to make this connection when the controller is installed in the server.Notes:a.The following illustration shows the controller installed in a PCI Express slot in the server.Yourserver configuration might be different.b.For more information about mounting the battery unit in the server,see the documentation thatcomes with the server.(installed remotely in00L i I o n000Figure 1.Mounting the battery unit in the server4Connecting the battery unit to the transportable memory module on the controllerIf the controller to which you are connecting the battery module is installed in thesever,use thefollowing procedure to first remove the controller from the server.Otherwise,go to“Connecting the battery unit and reinstalling the controller in the server”on page6.Removing the controller from the serverTo remove the controller from the server,complete the following steps:1.Read the safety information that comes with the controller.2.If you have not already done so,turn off the server and peripheral devices and disconnect the powercords.Remove the server cover.For more information,see the installation instructions that come with the server.3.Ground yourself before you touch the controller.4.Disconnect all cables from the controller,remove the screw that attaches the bracket to the server,andcarefully remove the controller from the slot.Notes:a.The following illustration shows the controller installed in a PCI Express slot in the server.Yourserver configuration might be different.b.For more information about removing the controller from the server,see the documentation thatcomes with the server.5.Place the controller on a flat,clean,static-protective surface,and continue with the next section.Figure2.Removing the controller from the server5Connecting the battery unit and reinstalling the controller in the server To connect the battery unit and reinstall the controller in the server,complete the following steps:1.With the controller on a flat,clean,static-protective surface,ground yourself and make sure that the server is grounded.2.Make sure that the ServeRAID M5100Series 512MB Cache/RAID 5Upgrade for IBM System x (transportable memory module)is mounted on the controller.For the mounting instructions,see the Quick Installation Guide that comes with the transportable memory module.3.Connect the battery unit to the transportable memory module:a.Select one of the 20-pin remote-mount cables that come with the battery unit,making sure that it has the correct length for your configuration.The battery unit comes with a 50cm (19.7in.)remote-mount cable and a 95cm (37.4in.)remote-mount cable.b.Connect one end of the 20-pin cable to the battery unit (remotely mounted in the server)and the other end of the cable to the 20-pin cable connector on the transportable memory module that is mounted on the controller.Attention:If you have to remove the controller after the battery unit is connected to it,you must disconnect the remote-mount cable from the transportable memory module on the controller and then remove the controller from the server.Notes:1)The following illustration shows the controller installed in a PCI Express slot in the server.Your server configuration might be different.2)For more information about installing the controller in the server,see the documentation that comes with the server.00L i I o n0000Figure 3.Connecting the battery unit to the transportable memory module and installing the controller in the server 64.Position the controller by aligning the PCIe x8connector with the PCIe x8slot on the system board.Insert the controller firmly into the connector and press down on the top edge of the controller so that it is firmly seated in the connector.See the previous illustration for the correct place to press on the controller.Note:Do not apply pressure to the transportable memory module when you insert the controller.Instead,press down only on the top edge of the controller.5.Replace the expansion-slot bracket screw if you removed it.6.Reconnect the controller to the SAS and SATA devices in the server.7.Replace the server cover,reconnect the power cords,and turn on the server.Replaceable componentsField replaceable units(FRUs)must be replaced only by a trained service technician,unless they are classified as customer replaceable units(CRUs).Tier1CRU:Replacement of Tier1CRUs is your responsibility.If IBM installs a Tier1CRU at your request without a service contract,you will be charged for the installation.Tier2CRU:You may install a Tier2CRU yourself or request IBM to install it,at no additional charge, under the type of warranty service that is designated for your product.For more information about the terms of the warranty and getting service and assistance,see the Warranty Information document that comes with the controller.Table1.Field replaceable units for the ServeRAID M5100Series Battery Kit for IBM System xDescription CRU part number(Tier1)CRU part number(Tier2)FRU part number(trained service technicianonly)ServeRAID M5100Series Battery Kit forIBM System x81Y4491Remote-mount cables for ServeRAIDM5100Series Battery Kit for IBM System x(2cables)90Y73097Getting help and technical assistanceIf you need help,service,or technical assistance or just want more information about IBM products,you will find a wide variety of sources available from IBM to assist e this information to obtain additional information about IBM and IBM products,determine what to do if you experience a problem with your IBM system or optional device,and determine whom to call for service,if it is necessary. Before you callBefore you call,make sure that you have taken these steps to try to solve the problem yourself:v Check all cables to make sure that they are connected.v Check the power switches to make sure that the system and any optional devices are turned on.v Check for updated firmware and operating-system device drivers for your IBM product.The IBM Warranty terms and conditions state that you,the owner of the IBM product,are responsible for maintaining and updating all software and firmware for the product(unless it is covered by an additional maintenance contract).Your IBM service technician will request that you upgrade your software and firmware if the problem has a documented solution within a software upgrade.v If you have installed new hardware or software in your environment,check / systems/info/x86servers/serverproven/compat/us/to make sure that the hardware and software is supported by your IBM product.v Go to /supportportal/to check for information to help you solve the problem.v Gather the following information to provide to IBM Support.This data will help IBM Support quickly provide a solution to your problem and ensure that you receive the level of service for which you might have contracted.–Hardware and Software Maintenance agreement contract numbers,if applicable–Machine type number(IBM4-digit machine identifier)–Model number–Serial number–Current system UEFI and firmware levels–Other pertinent information such as error messages and logsv Go to /support/entry/portal/Open_service_request/to submit an Electronic Service Request.Submitting an Electronic Service Request will start the process of determining a solution to your problem by making the pertinent information available to IBM Support quickly and efficiently.IBM service technicians can start working on your solution as soon as you have completed and submitted an Electronic Service Request.You can solve many problems without outside assistance by following the troubleshooting procedures that IBM provides in the online help or in the documentation that is provided with your IBM product. The documentation that comes with IBM systems also describes the diagnostic tests that you can perform. Most systems,operating systems,and programs come with documentation that contains troubleshooting procedures and explanations of error messages and error codes.If you suspect a software problem,see the documentation for the operating system or program.Using the documentationInformation about your IBM system and preinstalled software,if any,or optional device is available in the documentation that comes with the product.That documentation can include printed documents, online documents,readme files,and help files.See the troubleshooting information in your system documentation for instructions for using the diagnostic programs.The troubleshooting information or the diagnostic programs might tell you that you need additional or updated device drivers or other software. IBM maintains pages on the World Wide Web where you can get the latest technical information and download device drivers and updates.To access these pages,go to /supportportal/. Also,some documents are available through the IBM Publications Center at /shop/ publications/order/.8Getting help and information from the World Wide WebOn the World Wide Web,up-to-date information about IBM systems,optional devices,services,and support is available at /supportportal/.The address for IBM System x information is /systems/x/.The address for IBM BladeCenter®information is/systems/bladecenter/.The address for IBM IntelliStation®information is/systems/intellistation/.How to send Dynamic System Analysis data to IBMUse the IBM Enhanced Customer Data Repository to send diagnostic data to IBM.Before you send diagnostic data to IBM,read the terms of use at /de/support/ecurep/terms.html. You can use any of the following methods to send diagnostic data to IBM:v Standard upload:/de/support/ecurep/send_http.htmlv Standard upload with the system serial number:/app/upload_hwv Secure upload:/de/support/ecurep/send_http.html#securev Secure upload with the system serial number:https:///app/upload_hwCreating a personalized support web pageAt /support/mynotifications/,you can create a personalized support web page by identifying IBM products that are of interest to you.From this personalized page,you can subscribe to weekly email notifications about new technical documents,search for information and downloads,and access various administrative services.Software service and supportThrough IBM Support Line,you can get telephone assistance,for a fee,with usage,configuration,and software problems with your IBM products.For information about which products are supported by Support Line in your country or region,see /services/supline/products/.For more information about Support Line and other IBM services,see /services/,or see /planetwide/for support telephone numbers.In the U.S.and Canada,call1-800-IBM-SERV(1-800-426-7378).Hardware service and supportYou can receive hardware service through your IBM reseller or IBM Services.To locate a reseller authorized by IBM to provide warranty service,go to /partnerworld/and click Find Business Partners on the right side of the page.For IBM support telephone numbers,see/planetwide/.In the U.S.and Canada,call1-800-IBM-SERV(1-800-426-7378).In the U.S.and Canada,hardware service and support is available24hours a day,7days a week.In the U.K.,these services are available Monday through Friday,from9a.m.to6p.m.9IBM Taiwan product serviceIBM Taiwan product service contact information: IBM Taiwan Corporation3F,No7,Song Ren Rd.Taipei,TaiwanTelephone:0800-016-8881011First Edition(March2012)IBM,the IBM logo,and System x are trademarks of International Business Machines Corp.,registered in many jurisdictions worldwide.Printed in USA©Copyright IBM Corporation2012.US Government Users Restricted Rights–Use,duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.(1P)P/N:81Y1389。

INSTALLATION GUIDE QuickGuard® STANDARD & EXPRESSTABLE OF CONTENT1. FOREWORD (1)2. SPECIAL NOTES (1)3. SAFETY PRECAUTIONS (1)4. FENCING DESCRIPTION (1)5. GENERAL INSTRUCTIONS (1)6. MODIFY FENCE (3)7. FENCE ASSEMBLING (5)Assemble framework (5)Fixation of infill material (13)Assembly of conventional door. (21)Assembly of sliding door. (23)8. QUICK GUARD-EXPRESS ASSEMBLY (25)9. CLEANING AND MAINTENANCE (27)10. TECHNICAL DATA (27)All given dimensions are in mm unless otherwise statedWe reserve the right to make technical changes or modify the contents of this document prior notice. With regard to purchase orders, the agreed particulars shall prevail. Troax AB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents – whole or in parts – is forbidden without prior written consent of Troax AB.1.FOREWORDThis installation guide describes how to assemble QuickGuard Standard fence in general.For installation of QuickGuard Express –see “QuickGuard Express Installation guide”2.SPECIAL NOTESPay attention to the following special notes in this guideImportant!A tip!3.SAFETY PRECAUTIONSAlways use adequate personal safety equipment during installation, e.g. safety googles and ear protection.Always use safety googles and ear protection when cutting aluminum profiles with a hacksaw or mitre saw, and use protection gloves when handling meshes, glass or other material that can have sharp edges.If the fence isn’t bolted to the ground, secure it temporary to p revent it from tipping over.4.FENCING DESCRIPTIONThere are two versions of QuickGuard fencing system available, QuickGuard Standard and QuickGuard Express. Both versions are aluminum systems and can be combined with each other if needed.The main difference between QuickGuard Standard and QuickGuard Express, is that Standard have a 44x44 profile between the posts and Express have a U-profile in between.QuickGuard Standard has more possibilities in terms of infill materials and adaptations.5.GENERAL INSTRUCTIONSFixation of the fence to the ground is normally done at the very end. Do not fix the fence to the floor unless vertical profiles (posts) are aligned vertically and parallel to each other.If possible, start the installation were the fence can stand free, e.g. a corner or were it can be supported temporary to a fixed part.L-brackets are used in corners, end posts, door blade etc.T-brackets are used when connecting e.g. two horizontal profiles with a post.There is no drilling or tapping needed to connect the aluminum profiles, just press the pre-assembled bracket against the profiles and loosen the screw(s) about one turn anti-clockwise. Then tighten the screw clockwise until it’s fixed.IMPORTANT!Make sure that hammer nut has turned (90°) into correct position in the aluminum profile.Lower and middle horizontal profile shall be connected to each post with one bracket, normally mounted on the side facing outwards from the machine.Upper horizontal profile shall be connected to each post with two brackets, one on the inside and one on the outside.6.MODIFY FENCEQuickGuard can easily be adapted and modified on site. Aluminum profiles, polycarbonate sheets, steel mesh e.t.c. can easily be cut without using any tools that generate heat (=no fire risk).•Avoid tools that can generate heat and cause a fire, e.g. angle grinder.•Make sure that material to be cut is adequately supported and clamped during the cutting operation.•Use adequate personal safety equipment.Cut meshWhen cutting the welded mesh the wire ends should be at least 15 mm or cut flush to the joining wire.DIMENSION TABLE FOR INFILL MATERIALSExampleA polycarbonate sheet shall be cut to fit an opening where A=1500 and B=800. According to the dimension table the sheet should be 1520 (1500+20) x 820 (800+20).7.FENCE ASSEMBLINGAssemble frameworkSTEP 1.Pre-mount floor brackets on to the post profile according to example pictures below. Make sure that bottom part of the floor bracket aligns with the profile end before tightening the fixation screws. Also, make sure that hammer nuts are positioned correctly inside the profile.Note!At least two (2) floor brackets shall be used on each postMark where the fence will be installed. Use a chalk line to get a straight line as a reference.STEP 3.Mount lower horizontal profile on to a post. Make sure that distance between floor and lower part of the horizontal profile is correct, and that hammer nuts are positioned correctly inside the profile.Note!Post must be mounted so that floor brackets are perpendicular to the fence.TIP!Use a spacer block to facilitate installation and mount the horizontal profile in correct position.Mount next post on to the horizontal profile. Use a spacer block to place the profile in correct position.Polycarbonate sheetTear off a small area of the protective film from both sides of the polycarbonate sheet (fig1), and insert infill material in lower part. Bend the sheet (fig.2) and/or press the post apart to insert the sheet in to the profile T-slot.Tip!Leave the protective film on as long as possible to prevent damages on the surface.MeshBend the mesh and/or press the post apart to insert the mesh in to the profile T-slot. Make sure that the mesh is oriented with the vertical wires facing closest to the outside.Steel panelBend the steel panel and/or press the post apart to insert the mesh in to the profile T-slot. The convex side of the steel panel should be facing outwards.If steel panel shall be secured with infill securing strip (JSM PL1_) and cellular rubber (JSM G2), cellular rubber have to be mounted on to the steel panel before inserting the steel panel in to the frame work. Cellular have to beLaminated glass 6,4mmMount rubberstrip (JSM G3) all around the glass.Fig.1 Fig.2 Fig.3Place the middle horizontal profile between the posts and press it down against the polycarbonate sheet. Lift the middle horizontal profile ~3mm and fix it with L-brackets. Make sure that distance between the two horizontal profiles are correct. It shall be possible to move the infill material ~3mm vertically and horizontally when profile is fixed.Mount the rest of the fence…3. 4.5. 6.7. 8.11. 12.13.Position the fence on the floor and make sure that door posts are aligned vertically and parallel to each other before fixing the fence to the floor. Use adequate fixation bolts and center the drill in the fitting holes (fig.1)Note!Make sure that posts are in line with each other and that door posts are parallel before fixing the fence to the floor.Fixation of infill materialSelection of fixation componentJSM PL1_ / -PL2_Infill securing stripJSM PL3 Panel lockJSM NL3 Net lockJSM G2 Cellular rubber 5x20mmProduct W JSM PL1_ 6,5 JSM PL2_7,5Polycarbonate sheetTear and fold up about 100mm of the protective film all around the sheet, on both sides before securing the sheet in the frame work.3mm thicknessUse infill securing strip (JSM PL1_) together with cellular rubber (JSM G2) or panel lock (JSM PL3) to secure the sheet in the frame.4mm thickness.Use infill securing strip (JSM PL2_) or panel lock (JSM PL3) to secure the sheet in the frame.5mm thicknessUse infill securing strip (JSM PL1_) or panel lock (JSM PL3) to secure the sheet in the frame.Fixation with panel lock JSM PL3Panel lock JSM PL3 is normally mounted from the outside of the fence, on all four sides. Mount panel lock evenly distributed every 300-400mm starting maximum 250mm from corner (fig 1). Tighten the torx (T25) screw so it penetrates the polycarbonate surface about 2mm, max torque 3Nm.Use a cordless drill machine with torque control when mounting panel lock.Fig 1Fixation with infill securing strip JSM PL1_ or JSM PL2_Infill securing strip JSM PL1_/-PL2_ is normally mounted from the outside of the fence, on all four sides. JSM PL1_/-PL2_ is available in a few pre-cut lengths as listed in table 1 below. Any other length has to be cut on site. Length should be about 2mm shorter than the distance between the connecting profiles.Table 1Laminated glassThe glass is mounted with a u-rubber strip (JSM G3) in the profile groove. Rubber strip should be mounted all around the glass, before the glass are inserted in to the frame work.• Use protection gloves. • Carry the glass upright• It’s recommended to be two persons handling the glass.Fig.1Mounting the rubber stripL= (L1+L2) x 2 + 50 Step 2Make a 90° V-cut out from the rubber stripStep 3Mount the rubber strip on to the edge of the glass. Step 4Fold the rubber strip and press it on to next edge.Step 5Make a new V-cut and press it on to the next edge.Step 6Mounting laminated glass and sound absorbing panel1.Premount vertical profiles with floor brackets by first loosening the screw anti-clockwise. Then tighten the screw clockwise in the usual way. A spacer between the floor and the lower horizontal profile will make the installation easier.3.Insert the sound absorbing panel (1) in to the frame and put the horizontal profile above (2). The perforated side of the panel should normally be facing towards the sound source.5.Insert the glass (1) in to the frame and put the upper horizontal profile above (3). 2.Assemble mounting profile JSM AS1 all around the panel. The profile should be fixed on to the panel. If it’s to loose, increase the slot a little by pressing the “walls” together.4.Assemble the U-rubberstrip (JSM G3) all around the glass.6.Insert next sound absorbing panel at the same way as described previously, see step 2 and 3 above.7.Insert next glass same way as described previously, see step 4 and 5 above.8.Fix the profiles with L- and T-brackets, two brackets on the upper part (inside and outside) if possible, and one bracket on the other parts, normally on the outside.9.Adjust the fence and fix it to the floor with accurate fixations.Normally two (2) floor brackets are used per post and then fixed with one (1) bolt per floor bracket. If only one (1) floor bracket is used per post, both (2) fixation holes must be used.Assembly of conventional door.1) Install and fix fence to ground. Mount L- and T-brackets (JSM 32B-K & JSM 33B-K) on both sidesof the fence on the top. Make sure the door posts are paralell to each other before fixing them to the ground.2) Premount the door. Mount L-brackets (JSM 32B-K) on both sides on corners.3) Open the hinges for access to the screws. Put the door on the ground in the opening and mount the hinges onto the fence. Make sure that nuts turn out correctly and lift the dorr to correct hight and then tighten the screws,4) Mount door stops (JSM D13A) and eventual safety switches.Assembly of sliding door.1) Install and fix fence to ground. Mount L- and T-brackets (JSM 32B-K & JSM 33B-K) on both sides of the fence on the top. Make sure the door posts are paralell to each other before fixing them to the ground.2Premount the sliding door. Slide in the suspension wheels (JSM D5) into the 44x44 profile before putting on the endcaps (JSM L1B). Mount L-brackets (JSM 32B-K) on both sides on corners.3) Mount guiding components (JSM D12 & JSM D12A) onto the fence.4) Take the premounted door blade and slide it in to the guiding rail and guiding components.5) Mount door stops (JSM D13 & JSM D13B) and eventual safety switches.8.QUICK GUARD-EXPRESS ASSEMBLY9.CLEANING AND MAINTENANCECleaningAluminium profiles (anodized)•Use a mild neutral detergent (pH 6-8) and/or waterPolycarbonate sheets•Use a mild soap solution and a soft cloth.•Do not use abrasive or highly alkaline cleaners.•Never scrape the sheet with squeegees, razor blades or other sharp instruments.•Do not clean sheet in hot sun or at elevated temperatures as this can lead to staining.10.TECHNICAL DATA。

NetStor ® iSUM530快速安装指南V7.0北京同有飞骥科技股份有限公司NetStor® iSUM530快速安装指南- 2 -文档修订记录版本号日期描述说明V1.0V1.1V7.02009-6-182010-8-162011-1-24初始版本添加16R1/2FS12两个机型公司名称变更，产品工程统一切换NetStor ® iSUM530快速安装指南- 3 -声 明● 北京同有飞骥科技股份有限公司2011年版权所有。

● 如未事先得到北京同有飞骥科技股份有限公司的任何书面许可，手册中任何部分都不得进行复制，或以任何形式、任何手段进行转载。

● 北京同有飞骥科技股份有限公司对本手册未作任何形式的担保，包括对具体用途的商品性和适用性的隐含担保。

北京同有飞骥科技股份有限公司对本材料中可能出现的任何错误都不承担任何责任。

● 本公司对文件中的资讯有最终解释权，如有变更，恕不另行通知。

● 手册中涉及第三方的品牌和名称是他们相应的拥有者的产权。

● NetStor ®为同有公司的注册商标。

NetStor® iSUM530快速安装指南- 4 - 目录第1章警告和注意事项 (1)1.1 警告 (1)避免受伤 (1)系统供电 (1)1.2 注意事项 (2)静电保护 (2)散热和通风 (2)1.3 安全规范要求 (3)第2章磁盘阵列介绍与安装 (6)2.1打开iSUM 530包装 (6)2.2安装导轨 (6)2.3 安装iSUM530磁盘阵列 (10)2.3.1安装HBA卡 (10)2.3.2安装磁盘 (10)2.3.3扩展柜的连接 (14)2.3.4 服务器与存储的连接 (16)2.3.5 连接管理链路 (17)2.3.6连接电源 (18)第3章启动磁盘阵列 (19)3.1 开启磁盘阵列电源 (19)3.2 磁盘阵列启动完成 (19)3.3 开启服务器 (19)第4章配置磁盘阵列 (20)4.1安装SANManager软件 (20)4.2进入管理界面 (21)4.3查看磁盘信息 (24)4.4创建RAID (25)4.5创建逻辑卷 (27)NetStor ® iSUM530快速安装指南- 5 - 4.6创建分区 (29)4.7创建映射 (32)4.8查询分区 (35)4.9对新分区初始化 (35)4.10读写数据 (35)第5章 技术支持 (36)5.1 联系技术支持部门 (36)5.2 技术支持服务方式 (36)NetStor ® iSUM530快速安装指南1第1章 警告和注意事项本章节包含在安装使用iSUM530磁盘阵列之前以及在安装使用过程中需要注意的一些事项。

3M Interconnect Products3MDR ConnectorSelection GuideHigh DensityInput/Output Connectors3M™ Mini Delta Ribbon (MDR) ConnectorsPerformance and Reliability in MiniatureThe Mini Delta Ribbon (MDR) is a half pitch interconnect system from 3M,designed to meet the needs of high speed/density input/output applications.With more than 20 years on the market, the MDR system is an establishedand well-proven solution for high density I/O.MDR enjoys widespread acceptance by offering a combination of design features:n Shielded shells provide EMI/ESD protectionn Pre-loaded ribbon contacts provide proven reliable connectionn IDC U-shaped contacts allow mass terminationn W ide range of pin counts and form factors enable design flexibilityAs one of the world’s most innovative companies, 3M is continually developing its products to meet your I/O needs. The currentrange of MDR system components can easily be expanded to meet the specific requirements of a broad range of applications.The MDR connector system contains a ribbon-style contact based on 0.050" centerlines. Both the receptacle and the mating plug containpre-loaded contacts for reliable contact during insertion and withdrawal cycles. The cable connectors utilize an insulation stripping U-contact to connect to the cable conductor wires. The contact is stamped from a high performance copper alloy, which provides an excellent combination of mechanical strength, electrical conductivity and corrosion resistance.Round Shielded Round Shielded Jacketed Round Shielded Jacketed Pleated Foil ShieldedWiremount ConnectorsIDC Wiremount Solder Plug, Shielded Non-Shielded IDC IDC Wiremount Straddlemount Plug Through-Hole Plug, Through-Hole Plug, Plug, Shielded Plug Receptacle Right Angle, Shielded3M™ MDR Assembly Press 10960For the assembly of the 3M™ MDR Wiremount Plug101XX-60x0 (14-100 pos.) Series onto 3M™ Round JacketedDiscrete Wire Cables (e.g. Series 3600, 3647, KU-C-).Accessories:n 10960 Hand Pressn 10961 Cutting Unit; includes2 spare blades (10970-9)n 10962-2000 Fixture Unit; includes 14, 20, 26, 36,40, 50, 68, 80 and 100 positionconnector stopsn 10964-1 Cable Clamp; Black,14–50 positionn 10964-2 Cable Clamp; Silver, 68–100 position3M™ MDR Hand Tool Kit 3829For the assembly of 3M™ MDR Wiremount Plug 101xx-60x0 (14-68 pos) Seriesonto 3M™ Round Jacketed Discrete Wire Cables (e.g. Series 3600, 3647, KU-C-).Right Angle Receptacle, Right Receptacle, Straight, Receptacle, Right Angle, Through-Hole Receptacle, Right Angle, Through Receptacle, Straight, Through-Hole, Condo Receptacle Angle, SCSI-2 Layout Through-Hole, Solder Tails Solder Tails, Shielded, Diecast -Hole, Solder Tails, Shielded Compliant Pin, ShieldedFor Boardlock andPanel MountingTS-0142MDR Jack SocketsFor I/OPanel MountingTS-0142SMT Receptacle Connectors SMT Receptacle Connectors Through-Hole ConnectorsReceptacle, Shielded, Receptacle, Shielded, Receptacle, Shielded, Receptacle, Shielded, Receptacle, Shielded, Receptacle, Shielded, SMT, Straight SMT, Right Angle SMT, Straight Through-Hole, Right Angle SMT, Right Angle Through-Hole, Straight Pincount10214-1210 PE 12214-51x0-00 FR 12214-82x0-00 FR 12214-11x0-00 FR 1410220-22x0 PE 10220-1210 PE 2010226-22x0 PE 10226-1210 PE 10226-1A10 PE 12226-51x0-00 FR 12226-82x0-00 FR 12226-11x0-00 FR 2610236-22x0 PE36 10240-1210 PE40 10250-1210 PE 12250-51x0-00 FR 50 68 72 80100132200x = 0 without Jack Socket x = 0 without Jack Socket x = 0 without Jack Socket x = 5 with Jack Socket x = 5 with Jack Socket x = 5 with Jack Socket Panel/Board Retention Ultra low signal skew Ultra low signal skew I/O Mounting Hardware I/O Mounting Hardware I/O Mounting Hardware for high data rate for high data rate for high data rate Jack Sockets Jack Sockets Jack Sockets transmission transmission 12600-S-08 12600-S-08 12600-S-08 x = 1 M2.5 (Standard) 12600-S-10 12600-S-10 12600-S-10 x = 0 M2.6 (Special) Horizontally 12600-S-12 12600-S-12 12600-S-12 balanced to resist tipping during wave TS-2123 TS-2123 TS-2123 soldering20µ" (0.50 µm) Gold 20µ" (0.50 µm) Gold 20µ" (0.50 µm) Gold 30µ" (0.76 µm) Gold 30µ" (0.76 µm) Gold 30µ" (0.76 µm) Gold PlatingWiping Area E68080 E68080 E68080E68080E68080 E68080 UL-File UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL Flammability -55°C to +85°C -55°C to +85°C -55°C to +85°C -40°C to +70°C -40°C to +70°C -40°C to +70°CTemp. Range YesYes YesYesYesYes *RoHS Compliant TS-0638 TS-0755TS-0874TS-2124TS-2125TS-2126Tech Sheet No.MDR Connector Mating ChartPart No. Tech Sheet Description SurfacemountThrough-HoleStraight Right Angle Straight Right Angle Condo 101xx-3000 TS-0669 MDR Solder Plug, Shielded 102xx-22x0 PE 102xx-1210 PE 102xx-62x2 PC 102xx-55x3 PC 102xx-M218 101xx-60x0 TS-0423 MDR IDC Wiremount Plug, Shielded10226-1A10 XE 102xx-52xx PC 10220-L8A9 PE102xx-1S10 XE10250-PB17 PE 101xx-900x TS-0698 MDR Straddlemount Plug N/A 102xx-1210 PE 102xx-62x2 PC 102xx-55x3 PC N/A102xx-1S10 XE102xx-52xx PCPart No. Tech Sheet Description Straddlemount Wiremount Solder102xx-0210 TS-0425 MDR Boardmount Plug 101xx-900x101xx-60x0 xx101xx-3000 xx102xx-R2xxSTS-09613M ™ Shrunk Delta Ribbon SystemSMT Receptacle Connectors SMT Receptacle Connectors Through-Hole ConnectorsReceptacle, Shielded, Die-Cast Receptacle, Receptacle, Shielded, Receptacle, Shielded Receptacle, Shielded, Receptacle, Shielded, Receptacle, Shielded,SMT, Straight Shielded, SMT, Right Angle SMT, Right Angle SMT, Straight Through-Hole, Right Angle SMT, Right Angle Through-Hole, Straight Pincount 10214-1S10-PC 10214-1210 PE 12214-51x0-00 FR 12214-82x0-00 FR 12214-11x0-00 FR 1410220-22x0 PE 10220-1S10-PC 10220-1210 PE 2010226-22x0 PE 10226-1S10-PC 10226-1210 PE 10226-1A10 PE 12226-51x0-00 FR PE 12226-82x0-00 FR 12226-11x0-00 FR 2610236-22x0 PE36 10240-1S10-PC 10240-1210 PE40 10250-1S10-PC 10250-1210 PE 12250-51X0-00 FR 50 68 72 80 100132200 X = 0 without Jack Socket X = 0 without Jack Socket X = 0 without Jack Socket X = 5 with Jack Socket X = 5 with Jack Socket X = 5 with Jack SocketPanel/Board Retention Rugged die-cast body Ultra low signal skew Ultra low signal skew I/O Mounting Hardware I/O Mounting Hardware I/O Mounting Hardware for high data rate resists tipping during for high data rate for high data rate Jack Sockets Jack Sockets Jack Sockets automated soldering transmission transmission 12600-S-08 12600-S-08 12600-S-08 operations 12600-S-10 12600-S-10 12600-S-10 x = 1 M2.5 (Standard) Horizontally balanced 12600-S-12 12600-S-12 12600-S-12 x = 0 M2.6 (Special) Ultra low signal skew to resist tipping for high data rate during wave soldering TS-2123 TS-2123 TS-2123 transmission 20µ" (0.76 µm) Gold L = 8 µ" Gold with Lubricant 20µ" (0.76 µm) Gold 20µ" (0.76 µm) Gold 30µ" (0.76 µm) Gold 30µ" (0.76 µm) Gold 30µ" (0.76 µm) Gold Plating Wiping Treatment, E = 20 µ" Gold, Area C = 30 µ" Gold E68080 E68080 E68080 E68080 E68080E68080 E68080 UL-File UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL 94V-0 UL-Flammability -55˚C to +85˚C -55˚C to +85˚C -55˚C to +85˚C -55˚C to +85˚C -40˚C to +70˚C -40˚C to +70˚C -40˚C to +70˚C Temp. Range Yes Yes YesYes YesYesYes *RoHS Compliant TS-0638 TS-2242 TS-0755 TS-0874 TS-2124 TS-2125TS-2126 Tech Sheet No.Metal 10314-3210-000 10314-A200-00 10314- A500-00Plastic10314-52A0-008 10314-52F0-008 10314-42A0-008 10314-42F0-00810320-52A0-008 10320-52F0-008 10320-42A0-008 10320-42F0-008High Speed MDR Cable Assemblies3M ™ Mini Delta Ribbon (MDR) High Speed Transmission SystemThe 3M MDR High Speed Transmission System is a digital interconnect system designed to meet the needs of today’s high performance data transmission applications.Low Voltage Differential Signaling (LVDS) technology meets the requirements for a general purpose, high bandwidth interface for serialand parallel data at speeds up to 655 Mbps. The LVDS Standard is based on the use of 100 Ohm differential impedance transmission medium from driver to receiver. Signal skew is the largest factor inhibiting speed within a system and can occur at all points along the transmission path: driver to receiver circuits, circuit board traces, cables and connectors. Both types of skew within pair skew and channel skew can prohibit optimum performance in high speed transmission systems. 3M MDR Connectors provide an excellent solution for the demanding requirements of LVDS applications.3M ™ MDR High Speed Cable Assemblies for Camera Link ® Standard Machine Vision Applicationsn Supports the Automated Imaging Association’s Camera Link Standardfor industrial camera to frame grabber communicationsn 11 shielded twisted pairs and four drain wires n Entire cable bundle is shielded with foil and braidfor additional signal protectionn Rugged MDR ribbon type contact n Rugged thumbscrew retentionn EMI shielded junction shell in either plastic orovermolded constructionn RoHS * compliant3M ™ Shrunk Delta Ribbon (SDR) High Speed Cable Assemblies for Mini Camera Link ® Standard Machine Vision Applicationsn Supports AIA Industrial Mini Camera Link Standardfor new Mini C/L camera to frame grabber applicationsn 11 shielded twisted pairs with four drain wires n Entire cable bundle is shielded with foil and braidfor additional signal protectionn Rugged ribbon contact type n Rugged thumbscrew retentionn Available right angle overmolded SDR backshellseliminate bend radiusn EMI shielded cable assemblyn A vailable in configurations to mate between Mini Camera Linkand Camera Link products3M ™ LVDS/TMDS High Speed Cable Assemblies Transmission Systemsn Several shielded differential pairs (according to application)n Supports VESA/DFP standard for 20-position MDR at host device n LCD monitor assembly for Panel Link ™/TMDS interface n Solution for Digital Displays, Datacom and Telecom applications n Supports LVDS FP Link, Flat Link ™, Channel Link ™,Panel Link ™/TMDS electrical interfacesn Each differential twin-ax pair has foil shield and drain wire n Entire cable bundle is shielded with foil and braidfor additional signal protectionn Rugged MDR ribbon type contact n Quick release latches or thumbscrews n RoHS * compliant*RoHS Statement:“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. This information represents 3M ’s knowledge and belief, which may be based in whole or in part on information provided by third party suppliers to 3M.In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty (see back cover).Electronic Solutions Division Interconnect Products6801 River Place Blvd.Austin, TX 78726-9000800/225 5373Fax 800/325 5329/interconnectsPlease recycle. Printed in USA.© 3M 2008. All rights reserved.80-4000-1965-1 (080810) K/TG-133M is a trademark of 3M Company. Channel Link is a trademark of National Semiconductor. Flat Link is a trademark of Texas Instruments. Mini Camera Link and Camera Link are certification marks of Automated Imaging Association. Panel Link is a trademark of Silicon Image, Inc.Important NoticeBefore using this product, you must evaluate it and determine if it is suitable for your intended application.Y ou assume all risks and liability associated with such use.Warranty; Limited Remedy; Limited Liability.3M’s product warranty is stated in its Product Literature available upon request. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted.。

迅达5400A P M M R现场安装手册(总126页)-CAL-FENGHAI.-(YICAI)-Company One1-CAL-本页仅作为文档封面，使用请直接删除安装缩略图摘要本手册提供了在亚太区范围内使用脚手架安装300P MMR主要安装步骤的详细说明。

本手册为保密文件，并仅供授权的培训人员使用。

目录1 安全建议 (4)1.1 概要 (4)1.2 使用符号 (4)2 先决条件 (5)2.1 产品概述 (5)2.2 安装步骤 (7)2.3 专用工具 (9)3 施工现场准备工作 (10)4 导轨安装 (15)4.1 准备工作 (15)4.2 导轨支架安装 (15)4.3 导轨安装 (21)4.3.1 导轨基座 (21)4.3.2 导轨安装 (22)4.4 连接板校正 (24)5 Varidor 30AP C2 厅门入口安装 (25)5.1 门框预安装 (27)5.2 地坎支架 (30)5.3 门框和机械横梁 (31)5.4 地坎和护脚板 (35)5.5 门板 (36)5.6 C2井道互锁装置 (40)5.7 门解锁装置 (41)5.8 安装门重锤 (42)5.9 防护罩 (44)6 PMS420无齿轮机组安装 (45)6.1 机组支架 (47)6.2 安装PMS420无齿轮机组 (48)6.3 *手动应急操作选配装置 (51)6.4 制动器调整和制动力测试 (57)6.5 *曳引钢丝绳悬挂装置安装 (58)6.6 *安装限速器 (62)7 *安装GGM2-AP对重 (71)7.1 先决条件 (71)7.2 *机械安装 (72)7.2.1 *缓冲器支撑 (72)7.2.2 *对重校正 (73)7.2.3 *安全钳（选配） (74)7.2.4 *导靴 (76)7.2.5 油杯（选配） (79)7.2.6 *对重块 (79)7.2.7 *补偿链悬挂装置 (80)7.2.8 地震传感器（选配） (81)7.3 *调整和最后检查 (82)7.4 对重防护屏 (83)7.4.1 *对重防护屏后置 (83)7.4.2 *对重防护屏侧置 (84)8 安装轿厢架FRS9-AP/FRM9-AP (87)8.1 安装轿厢架FRS9-AP (87)8.2 FRS9-AP安全钳和导靴选配件 (98)8.3 FRM9-AP安全钳和导靴选配件 (99)9 安装曳引绳 (100)9.1 处理钢丝绳 (100)9.2 安装钢丝绳 (101)9.3 钢丝绳绳头安装 (105)9.4 检查钢丝绳张紧度和绳的润滑 (109)9.5 限速器钢丝绳 (110)10 轿厢P9KD-AP(CM)安装 (117)10.1 轿厢安装步骤 (118)10.2 *安装轿厢装璜 (134)10.3 安装满载、超载开关 (143)10.4 轿厢平衡装置 (144)11 V30 AP轿门安装 (145)11.1 C2轿门 (145)11.1.1 轿门机驱动 (146)11.1.2 轿门板 (147)11.1.3 轿门刀 (149)11.2 安装光幕(MiniMax光幕LVH) (151)12 安装缓冲器 (157)13 安装补偿链 (159)13.1 补偿链导向装置 (159)13.1.1 4-滚轮导靴 (159)13.1.2 2-滚轮导靴 (162)13.2 补偿链 (165)14 安装MX-GC (170)14.1 先决条件 (170)14.2 材料范围 (171)14.3 控制柜 (172)14.4 井道信息 (174)14.4.1 井道信息IGSI (174)14.4.2 绝对值线型井道信息系统 (190)14.5 控制柜内模块 (210)14.6 机房电缆 (211)14.7 井道电缆 (215)14.7.1 准备 (220)14.7.2 安装 (223)14.7.3 调整和最后检查 (229)14.8 OKR (231)14.9 随行电缆 (236)14.9.1 带IGSI和LONCIB的MX-GC，HQ<=70m (237)14.9.2 带IGSI和LONCIB的MX-GC，HQ>70m (238)14.9.3 带IGSI和LONIC/LONICK的MX-GC，HQ<=70m (239)14.9.4 带IGSI和LONIC/LONICK的MX-GC，HQ>70m (240)14.10 控制柜内ASIXA32.Q的概述与名称 (241)15 VARIODYN VF44BR和VF88BR安装 (243)15.1 VARIODYN VF44BR安装 (243)15.2 VARIODYN VF88BR安装 (249)1 安全建议1.1 概要安全要求所有参与的安装人员必须熟悉并遵守公司以及当地的安全规范，特别要注意以下几点：•照明必须充足，以保证安全生产。

CLI及WEB网管操作本章将介绍如何通过CLI网管来配置MG6000系列设备，进行CLI配置的同时会以图片的形式标明WEB界面中对应的配置项。

1.1 Web网管的登录1.1.1 Web网管的配置模式Web网管只有一种配置模式，用户在一个IE窗口内完成对设备的配置。

Web网管定义了三种不同的用户权限，分别为普通用户、高级用户、超级用户。

只有高级用户和超级用户才有修改配置的权限。

超级用户还具有完成配置保存、配置恢复、软件升级等其他等级用户所不具备的权限。

Web网管的出厂默认用户名和密码如表4-1所示。

问高等级用户才有权访问的页面，系统会提示用户无权访问，请用户进入登录页面重新登录。

1.1.2 系统登录在IE浏览器的地址行中输入http://xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx为设备IP地址)，进入登录页面（如图4-1所示）。

只有在输入合法的用户名和密码后，才可以进入网管主页面。

Web网管支持中英文切换，进入英文界面请点击【English Version】。

图1-2 进入WEB登录页面注意：1.设备出厂时WAN口的默认IP为：138.0.60.1,子网掩码：255.255.0.0，LAN口的默认IP为：192.168.1.1，子网掩码：255.255.255.0；2.在登录系统之前，必需确保电脑与设备在同一网段，例如：通过WAN口将设备与电脑相连，如果设备W AN口IP为出厂时默认的IP，可以将电脑的IP设置为：138.0.0.221，子网掩码：255.255.0.0；1.2 CLI网管的基本命令CLI网管有两种配置模式，用户模式和特权模式。

不同的模式下可操作的命令有所不同。

在用户模式“MG6016>”提示符下输入<?>，会列出用户模式下可用的所有命令和命令的解释；在特权模式“MG6016#”提示符下输入<?>，会列出特权模式下可用的所有命令和命令的解释。