烘炉燃烧控制器故障代码说明
- 格式：xls
- 大小：54.50 KB
- 文档页数：26
在错误的时间，继电器模块控制回 路激活
35
Call Service
报警
安全继电器应闭合时断开或者保险 死熔断
36
Call Service
报警
Main valve terminal was off when it should be on, or the internal 主阀端子应闭合时断开 fuse has blown. Pilot(Igntion)valve terminal was off when it should be on,or the 燃烧器阀门端子应闭合时断开 internal fuse has blown. Igntion terminal was off when it should be on,or the internal 点火端子应闭合时断开 fuse has blown. V2S valve terminal (usually terminal 21)was off when it should be on,or the internal fuse has blown. Safety relay was on when it should be off.
18
Flame Detected
火焰探测
Flame sensed when the shutter is 在预吹扫阶段，断路器打开，无火 open and no flame is expected 焰，但是探测到了火焰信号 during PREPURGE.
19
Main Flame lgn.
主火焰点燃
Flame was lost during MFEP or the first 10 seconds of the RUN state.
在MEEP或者运行状态最初的10秒钟 内，火焰熄灭
20
Low Fire Sw. Off
Low Fire interlock switch 低位火焰开关断开 failure to close during PREPURGE.
在待机状态，无火焰时出现了火焰 状态
16
Flame-Out Timer
火焰熄灭
No-flame detected during Pilot Flame Establishing Period.
在长明灯运行期间，检测不到火焰
17
Main Flame Fail
主火焰失败
Main flame failure during Run 点火成功后并运行至少10秒后，主 afted flame is established an on 火焰熄灭 ofr at least 10 seconds.
霍尼韦尔燃烧控制器故障代码
故障代码序号 Fault Code 故障代码 System Failure No card is plugged into the purege card slot 系统故障
Fault 1
"NO Purge Card"
无吹扫卡
无卡插入吹扫卡槽
Fault 2
AC Frequen/noise
设备在快频下运行
Fault 5
Low Line Voltage
低电压
Low ac line detected.
检测到低压交流电路
Fault 6
Purge Card Error
吹扫卡错
Purge card timing changed since card was initially read.
由于读了错误卡，吹扫时间改变
46
Flame Amp Type
火焰放大器
Device specific.
a、当仪器带电时，来自放大器的 FFRT或TYPE的输入值改变b、标准 的放大器用在了副阀上c、3秒火焰 失败响应时间放大器与再点火选择 一起用在RM7890继电模块上
47
Jumpers Changed
The configuration jumpers differ 端子连接卡不同于启动时所用的样 端子连接卡改变 from the sample taken at 品 startup. V2S Valve terminal,used as a delayed main valve,was on when it should be off.
火焰连锁（继电器）应断开时闭合
25
Call Service
报警
火焰连锁（继电器），应闭合时断 开
26
Man-Open Sw. Off
手动开关打开
The Manual Open Valve Switch was 手动开关应闭合时打开 off when it should be on(Device （RM7838B） specific)
交流频率/噪音
Excess noise or device running on slow ac.
噪音过大或者设备在低频下运行
Fault 3
AC Line Dropout
交流线路掉线
Ac line dropout detected.
检测到交流线路掉线
Fault 4
AC Frequency
交流频率
Device running on fast ac.
Hale Waihona Puke 在预吹扫阶段，低位火焰连锁开关 不能闭合
21
Running ILK
运行连锁
Running interlock fault during PREPURGE.
在预吹扫阶段，运行连锁故障
22
Lockout ILK
停机连锁
Lockout interlock fault during PREPURGE.
在预吹扫阶段，停机连锁故障
在运行期间，低火焰连锁开关不能 闭合
32
Airflow Switch
空气开关
Combustion Airflow interlock fault.
燃烧空气开关连锁失败
33
Pre-Igntion ILK
预点火连锁
Pre-Igntion interlock fault.
预点火连锁失败
34
Control On
点火火焰失败
29
Lockout ILK
停机连锁
Lockout interlock fault.
停机连锁故障
30
Running ILK
运行连锁
Running interlock fault.
运行连锁故障
31
Low Fire Sw. Off
Low Fire interlock Switch 低位火焰开关断开 failure to close during RUN(Device specific)
连接卡错
The sequence logic detected a combination of jumpers that is illegal ofr the sequence,e.g.,if 逻辑顺序探测到了不合法的连接卡 it is correct to clip jumper JR1 组合 or Jumper JR2,but not both,this fault woould be used when both are clipped(Device specific).
主阀端子应断开时闭合
42
Pilot Valve On
点火阀门闭合
Pilot(Igntion)Valve terminal was 点火阀端子应断开时闭合 on when it should be off.
43
Igntion On
点火闭合
IIgntion terminal was on when it 点火端子应断开时闭合 should be off.
14
High Fire Sw.
High Fire interlock Switch 高火位火焰开关 failure to close during PREPURGE.
在预吹扫段，高火焰连锁开关不能 关闭
15
Flame Detected
火焰探测
Flame sensed when no flame is expected during STANDBY.
27
Start Switch On
启动开关闭合
Start Switch was on during PREPURGE(Device specific).
在预吹扫阶段，启动开关闭合（仅 RM7838A，RM7838B）
28
Pilot Flame Fail
点火火焰失败
Pilot flame failure.
44
Pilot Valve 2 On
点火阀2闭合
V2S valve terminal,used as a pilot,is on when it should be off.
用作点火回路V2S阀端子，应断开 时闭合
45
Low Fire Sw. Off
低位火焰开关断开
Low Fire interlock switch 低位火焰连锁开关不能闭合或闭合 failure to close or stay closed. 不开
控制开
CTL input was energized at the wrong time for the relay module.This fault implies a field wiring error. Safety relay was off when it should be on or the internal fuse has blown.
48
Delayed MV On (2nd Stage Valve)
