模具英语

模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。

模具英语专业术语模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。

替换镶件：Interchangeable Mold Inserts。

模芯：Parting Core。

侧抽芯：Side Action 。

脱螺纹：unscrew。

excluding metallic parts price：不包括五金件价格。

Subtract to button up, convenient mold：反向弹出：reverse eject，硬度：hardness 。

牛角进胶：cashew gate 。

runner system：浇道系统。

stress crack：应力电裂。

orientation：定向。

sprue gate；射料浇口。

直浇口：nozzle射嘴。

slag well：冷料井。

bronze：青铜。

brass；黄铜。

prototype mold；手办模。

side gate：侧浇口。

edge gate：侧缘浇口。

tab gate：搭接浇口。

film gate：薄膜浇口。

flash gate：闸门浇口。

slit gate：缝隙浇口。

fan gate：扇形浇口。

dish gate：因盘形浇口。

Mold working automatic 模具自动生产 overmolding 包胶模H=F=1/2t~1/5t 。

T=2.5~3.5mm 。

diaphragm gate：隔膜浇口。

ring gate：环形浇口。

Sub gate：潜入式浇口。

tunnel gate：隧道式浇口 pin gate：针点浇口。

晒纹Texturing。

方铁;Spacer Block . 顶针板:Ejector Plate。

There are under cut at this area of part 零件这处有倒扣，can not be released 不能脱模 runner shut off 转水口cavity and core direct cut on A.B-plate 料位在A,B板上原身出。

2 stage ejection 二次顶出interchangeable cavity,core and sliders for each part互换前后模和行位生产每一个产品。

汽车冲压模具英语词汇Die / Tool= 模具Prog. Die=progressive die 级进模Casti ng die=W 造模Part=ffi 件Die material=制模材料Tool desig门=模具设计Strip desig门=料条设计Tool desig n approval^ 具设计审核Tool desig n modificatio n/revisio n=模具设计更改Tool parts design （detail） = 模具钣件设计（详细）FMC Make=保丽龙制作modification= 更改Check & measured查& 测试Machining= 机器加工Large m a c h i n i n g =在大型机器上加工上下模架（铣、车等）Small machi ning二在小型机器上加工模块等Assembly 二组立NC Machining=NC 雕刻加工Fitti ng=研磨组立Spott ing二合模Dowel pi n=定位销Assemble gas spri ng安装氮气缸Adjustme nt=调试Lower trim steels=下刃块Sectio门=冲头断面Trim pun ch=切刃冲头jack screw hole=起重［千斤顶］螺旋孑L Die set, lower plate=T 模架Die set, upper plate=h 模架Ball beari ng guide posts and bush in §$=球形滚珠导柱和轴套Cage=®Rigidity= 强度Thi n=薄Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”Heeled die sets, internally heel form & trim sections^箱根的模架，成形与切刃冲头带导引Con structio n method^ 构方法Lower die trim in serts=下模切刃块Lower trim in serts retai ner=T 模切刃块承盘Assemble in serts=fi 立镶块Punch stripp ing platesh 中头压料板Trim punch back ing plates=切刃冲头背板Stripper wi ndow in serts=# 条窗户镶块Die tryout=试模Cushi ng stroked 冲行程Guide lift pin= 导引升降销Stamp partsh 中钣件Run off parts=中钣件Hit parts=冲钣件Lifters=提升器Coil=卷材Guide block 二导弓I块Guide the coil through the tool=# 引卷材layout in spectio n=全尺寸检验Die in specti on & approval=模具检查和审核delivery=发货Rejected* 收Scrapped=报废Rework=返工stop block=停止块Hydro form液压成形Shear=K 切Sen sor=ft 感器Stretch web=S 伸网Layout the parts=S 计钣件Preced ing into the desig n继续设计Guide the coil through the tool=# 弓I卷材Check ing aid /check ing gage=检具Jig=夹具Fixture=夹具Ball beari ng guide posts and bush in gs= 球形滚珠轴套Guide post=导柱Bushings二导套Using material thickness radii where sharp corners are shown on the part reduces the occurre nee of chipped punch or die corners in the tool.=在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”Heeled die sets, intern ally heel form & trim sectio ns=带箱根的模架，成形与切刃冲头带导引Gra nite Tabled 岗岩平台Plotter=.描绘器,图形显示器,绘图器,坐标自记器，标图员Belt San der=# 磨机Metal Cutti ng Ba nd Saw^ 式带锯床Bla nchard Grin der=大型平面磨床Stretch carriers=S 伸运送装置Punch stripp ing platesh 中头压料板Trim punch back ing plates=切刃冲头背板Stripper wi ndow in serts=M 条窗户镶块Heel plates=W 托Prepare for delivery^® 备发货Key=键For locati ng reta iner blocks^ 盘键For holdi ng butt ons or pilots=冲母座或导销键For fixed heel or positive stop=B 根键Con structio n method=S 构方法Manual Surface Grin der=手动平面磨床Spott ing red=合模用丹红Layout ink=试模用蓝墨水Masking tape=M色不透明胶带(遮蔽胶带) Pliers=尖嘴钳，老虎钳Crese nt wren ch=可调扳手Pump pipe=泵管CMM=三次元测量仪Symmetric=对称的The axis of symmetry^ 称轴Tech nical^ 术上的Diago nal=对角线One two three block” 二三模块Adjustable parallels^ 调平行块Stop block=阻止块Backi ng Plate=背板Shoulder Bolt=肩头螺丝(Stripper bolt)Keeper Block=行程块Corner Guide Block=# 块Dowel pi n=定位销Joe Blocks=ft 密量块Whirly Gig=筒夹式冲子成形器Chamfer Tools= 到角刀具组Angle Plate=L形直角座Gage Pins=^寸塞规Si ne Plate (mag netic)=E 弦磁台Flute End Mill=硬质合金钢铣刀Mill Cutter=波纹粗铣刀(标准型) C' bore/ counter bore六角沉头铣刀Radius Dresser=^ 轮修整器Boring Head & Boring Bar=搪孔器、搪刀杆Pin二销Reamer=绞刀Approval 确认Impact wren ch二气动扳手Air pi n=空气销bumper[‘ bQmpE(rn.缓冲器Ven dor [ ‘ ven dE(r)d C:(r)] n.卖主stripper layout=排样图drawing of panel #987415&16=钣件设计图(公差)Arbor =柄轴；心轴Drill chuck=钻夹头Butt on=冲母座Nitroge n Cyli nder=氮气缸Pilot=导销Retai ner二承盘Butt on=冲母座Hose Straps嗽管夹(塑料)Set Screw=S 塞Jig & fixture =夹具Checking fixture二检具Guide Block 二导块Plu nger二柱塞Pierce=?中孑LWear Strip=W 磨板Mating area=ffl立的接触面Accommodate 二适应Wiping hard (very shiny)=过分摩擦闭合[接触](闪光)In crease the die cleara nee betwee n the form steels=®加成形块间隙Cleara nce= 间隙Oil paper 二油纸0-11” Micrometer=0-11 ”千分尺Trim line=切边+/-0.5mm uni ess otherwise specified除非另有规定，否则公差为+/-0.5mmPart tolera nce=R件公差Ball no se=球刀Bore二镗Line tap=攻丝校直Borer二镗刀，镗床Chamfer二倒角Radius=半径Coola nt=切削液Pun ch=^冲头Distribution Blocks=接头座Screw二螺丝Shop# 间Flat Feet Keepers顶料销Ejector Pin=顶出销Spring二弹簧Straight Port Adapter=直管接头Y-205 Hose=< 管(塑料)Short Neck Adapter=S 接头45 Swivel= 45 接头(adjustable) 45。

模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。

模具英语词汇表Aabrasive grinding 强力磨削L 3 a b r a s i v e[☜'breisiv] a.磨料的, 研磨的L2,3 absence ['✌bs☜ns] n.. 不在，缺席L17 accesssory[✌k'ses☜ri] n.附件L10 accommodate[☜'k m☜deit] v. 适应L 5 accordingly[☜'k :di☠li] adv.因此,从而,相应地L7,1 3 accuracy['✌kjur☜si] n精度,准确性L1, 3 a c t u a t e['✌k t j u e i t] vt.开动(机器), 驱动L8 adequate['✌dikwit] a. 足够的L1 3 adhesive[☜d'hi:siv] n. 粘合剂L2 2 adjacent[☜'d✞eisnt] a. 邻近的L1 3 adopt[☜'d pt] vt. 采用L 4 advance [☜d'v✌:ns] n.进步L7 advisable [☜d'vaizbl] adj. 可取的 L20 agitate['✌d✞iteit] v. 摇动L 2 a large extent 很大程度L4,1 3 algorithm ['✌l♈☜ri❆☜m] n. 算法L 6 align [☜'lain] v 定位，调准L17 alignment[☜'lainm☜nt] n. 校直L1 1 all-too-frequent 频繁L17 allowance[☜'l☜uens] n. 容差, 余量L5 alternate[' :lt☜nit]v.交替,轮流L 1 alternative[ :l't☜:n☜tiv] n. 替换物L 3 alternatively[ :l't☜:n☜tivli] ad. 做为选择, 也许L 5 aluminiun[ ✌lju'minj☜m] n.铝L 2 ample['✌mpl] adj. 充足的L20 analysis [☜'n✌l☜sis] n. 分析L 6 ancillary['✌nsil☜ri] a.补助的, 副的L 4 angular ['✌♈jul☜] adj. 有角的L20 annealing[☜'li:li☠] n.退火L 2 aperture ['✌p☜t☞☜] n.孔L17 applied loads 作用力L 1 ap p rop riat e [☜'p r☜up rieit] a. 适当的L6,20 arc[a:k] n.弧, 弓形L10 arise[☜'raiz] vi. 出现, 发生L2 1 arrange[☜'reid✞] v. 安排L1 2 article['a:tikl] n.制品, 产品L2 1 ascertain[ ✌s☜'tein] vt. 确定, 查明L 1 assemble[☜'sembl] vt.组装L 4 attitude ['✌titju:d] n 态度L17 auxiliary [ :♈'zilj☜ri]adj. 辅助的L8 avoid[☜'v id] v.避免L7 axis['✌ksis] n.轴L 5 axle['✌ksl] n.轮轴, 车轴L 1Bbackup['b✌k ✈p] n. 备份L9 batch [b✌t☞] n 一批L17 bearing['b☪☜ri☠] n.轴承,支座L2 1 bed[bed] n. 床身L 5 behavior[bi'heivj☜] n. 性能L 1 bench-work 钳工工作L 4 bend[bend] v.弯曲L 1 beneath[bi'ni: ] prep在···下L 4 bin [bin] n. 仓，料架L19 blank [bl✌☠k] n. 坯料L20 blank [bl✌☠k] v. 冲裁,落料L17 blanking tool 落料模L17 blast [bl✈st] n.一阵（风）L18 blemish['blemi☞] n. 缺点, 污点L1 3 bolster['b☜ulst☜] n. 模座,垫板L4,5 boost[bu:st] n. 推进L9 boring['b :ri☠] n.镗削, 镗孔L4, 5 bracket ['br✌kit] n. 支架L19 brass [br✌s] n.黄铜L 2 break down 破坏L 1 breakage ['breikid✞] n.破坏L17 bridge piece L1 6 brine[brain] n. 盐水L 2 brittle['britl] adv.易碎的L 1121buffer [b✈f☜] n.缓冲器L8 built-in 内装的L9 bulging [b✈ld✞i☠] n. 凸肚L2 2 burr [b☜:] n. 毛刺L17 bush [bu☞] n. 衬套L17 bush[bu☞]n. 衬套L 5 by far (修饰比较级, 最高级)···得多, 最L 3 by means of 借助于L 5Ccabinet ['k✌binit] n.橱柜L7 call upon 要求L17 carbide['ka:baid] n.碳化物L10 carburzing['ka:bjureti☠] n. 渗碳L 2 carriage['k✌rid✞] n.拖板, 大拖板L 5 carry along 一起带走L18 carry down over 从···上取下L2 1 carry out 完成L17 case hardening 表面硬化L 2 case[keis] n. 壳, 套L 2 cast steel 铸钢L17 casting['ka:sti☠] n. 铸造,铸件L 3 category['k✌t☜♈☜uri] n. 种类L6,1 5 caution ['k :☞☜n] n. 警告，警示L17 cavity and core plates 凹模和凸模板L1 1 cavity['k✌viti] n.型腔, 腔, 洞L4,10 centre-drilling 中心孔L 5 ceramic[si'r✌mik] n.陶瓷制品L 3 chain doted line 点划线L1 1 channel['t☞✌nl] n.通道, 信道L8 characteristic[k✌r☜kt☜'ristik] n.特性L 1 check[t☞ek] v.核算L2 1 chip[t☞ip] n.切屑, 铁屑L 3 chuck [t☞✈k] n.卡盘L5,8 chute [☞u:t] n. 斜道L19 circa ['s☜k☜:] adv. 大约L7 circlip['s☜:klip] n.(开口)簧环L2 2 circuit['s☜:kit] n. 回路, 环路L1 3 circular supoport block L 5 circulate['s☜:kjuleid] v.(使)循环L1 3 clamp [kl✌mp] vt 夹紧L17 clamp[kl✌mp] n.压板L1 2 clay[klei] n. 泥土L2,7 clearance ['kli☜r☜ns] n. 间隙L17 clip [klip] vt. 切断，夹住L19 cold hobbing 冷挤压L 4 cold slug well 冷料井L1 2 collapse[k☜'l✌ps] vi.崩塌, 瓦解L2 2 collapsible[k☜'l✌ps☜bl] adj.可分解的L2 2 combination [k mbi'nei☞☜n] n. 组合L18 commence[k☜'mens] v. 开始, 着手L1 6 commence[k☜'mens]v. 开始L2 1 c ommercial [k☜'m☜:☞☜l] adj. 商业的L7 competitive[k☜m'petitiv] a. 竞争的L9 complementary[ k mpli'ment☜ri] a. 互补的L 5 complexity [kem'pleksiti] n.复杂性L8 c o m p l i c at ed['k mp l☜keit id] adj.复杂的L2 complication [k mpli'kei☞☜n] n. 复杂化L5,20 compression [k☜m'pre☞☜n] n.压缩L 1 comprise[k☜m'prais] vt.包含L1 6 compromise['k mpr☜maiz] n. 妥协, 折衷L1 3 concern with 关于L 6 concise[k☜n'sais] a. 简明的, 简练的L9 confront[k☜n'fr✈nt] vt. 使面临L1 4 c o n n e c t or[k☜'nekt☜] n. 连接口, 接头L14 consequent['k nsikw☜nt] a. 随之发生的, 必然的L 3 console ['k nsoul] n.控制台L8 consume [k☜n'sjum] vt. 消耗, 占用L7 consummate [k☜n's✈meit] vt. 使完善L 6 container[k☜n'tein☜] n. 容器L1 1 c o n t i n gent[ken't ind✞☜nt] a.可能发生的L9 contour['k☜ntu☜] n.轮廓L5,2 1122c o nvent ional[k☜n'ven☞☜nl] a. 常规的L4 converge[k☜n'v☜:d✞] v.集中于一点L2 1 conversant[k n'v☜:s☜nt] a. 熟悉的L1 5 conversion[k☜n'v☜:☞☜n] n 换算, 转换L7 conveyer[ken'vei☜] n. 运送装置L1 2 coolant['ku:l☜nt] n. 冷却液L1 3 coordinate [k☜u' :dnit] vt. (使)协调L8 c o p y m a c h i n e仿形(加工)机床L4 core[k :] n. 型芯, 核心L2, 4 corresponding [ka:ri'sp di☠] n.相应的L7 counteract [kaunt☜'r✌kt] vt. 反作用,抵抗L20 couple with 伴随L20 CPU (central processing unit) 中央处理器L9 c r a c k[k r✌k] v.（使）破裂，裂纹L1,17 critical['kritikl] adj.临界的L 2 cross-hatching 剖面线L1 6 cross-section drawn 剖面图L1 1 cross-slide 横向滑板L 5 C R T(c a t h o d er-ray t ube) 阴极射线管L9 crush[kr✈☞]vt.压碎L 1 cryogenic[ krai☜'d✞enik ]a.低温学的 L 1 crystal['kristl] adj.结晶状的L 1 cubic['kju:bik] a. 立方的, 立方体的L 3 cup [k✈p] vt (使)成杯状, 引伸L18 curable ['kjur☜bl] adj. 可矫正的L20 curvature['k☜:v☜t☞☜] n.弧线L2 1 curve [k☜:v] vt. 使弯曲L20 cutter bit 刀头, 刀片L 3 cyanide['sai☜naid] n.氰化物L 2Ddash [d✌☞] n. 破折号L 6 daylight ['deilait] n. 板距L1 2 decline[di'klain] v.下落,下降,减少, L3,9 deform[di'f :m] v. (使)变形L1, 3 demonstrate['dem☜streit ] v证明L2 1 depict[di'pikt ] vt 描述L18 deposite [di'p zit] vt. 放置L20 depression[di'pre☞☜n] n. 凹穴L1 2 descend [di'sent] v. 下降L20 desirable[di'zair☜bl] a. 合适的L 2 detail ['diteil] n.细节，详情L17 deterioration[diti☜ri:☜'rei☞☜n] n. 退化, 恶化L1 2 determine[di't☜:min] v.决定L1 6 diagrammmatic[ dai☜gr☜'m✌tik].a.图解的，图表的L10 dictate['dikteit] v. 支配L1 2 die[dai] n.模具, 冲模, 凹模L 2 dielectric[daii'lektrik] n. 电介质L10 die-set 模架L19 digital ['did✞itl ] n.数字式数字, a.数字的L3, 6 dimensional[dddi'men☞☜nl] a. 尺寸的, 空间的L 3 discharge[dis't☞a:d✞] n.v. 放电, 卸下, 排出L 3 discharge[dis't☞a:d✞] v.卸下L8 d i s c r e t e[dis'cri:t] adj. 离散的,分立的L7 dislodge[dis'l d✞] v. 拉出, 取出 L1 2 dissolution[dis☜'lu:☞☜n] n.结束L9 distinct [dis'ti☠kt] a.不同的，显著的L 6 distort [dis'd :t] vt. 扭曲L20 distort[dis't :t] vt. (使)变形, 扭曲L 1 distributed system 分布式系统L9 dowel ['dau☜l] n. 销子L19 d r a m a t i c l l y[dr☜'m✌t ikli] adv. 显著地L7 drastic ['dr✌stik] a.激烈的L17 draughting[dra:fti☠] n. 绘图L1 6 draughtsman['dr✌ftsm☜n] n. 起草人L1 6 drawing['dr :i☠] n. 制图L1 1 drill press 钻床L8 drum [dr✈m] n.鼓轮L8 dual ['dju:☜l] adv. 双的，双重的 L18 ductility [d✈k'tiliti ] n.延展性L1,2 1123dynamic [dai'n✌mik ] adj 动力的L 6Eedge [ed✞] n .边缘L20 e.g.(exempli gratia) [拉] 例如L1 2 ejector [i'd✞ekt☜] n.排出器，L18 ejector plate 顶出板L1 6 ejector rob 顶杆L 5 elasticity[il✌'stisiti] n.弹性L 1 e l e c t r i c dicharge machining 电火花加工L3electrical discharge machining电火花加工L10 e l e c t r o c h e m i c a l machining 电化学加工L3 electrode[i'lektr☜ud] n. 电极L10 electro-deposition 电铸L 4 elementary [el☜'ment☜ri] adj.基本的L 2 eliminate[i'limineit] vt. 消除, 除去L10 elongate[i'l ☠♈et] vt. (使)伸长, 延长L 1 emerge [i'm☜:d✞] vi. 形成, 显现 L20 emphasise['emf☜saiz] vt. 强调L 4 endeavour[en'dev☜] n. 尽力L17 engagement[in'♈eid✞ment] n. 约束, 接合L2 2 enhance[in'h✌ns] vt. 提高, 增强L9 ensure [in'☞u☜] vt. 确保，保证L17 envisage[in'vizid✞] vt.设想L1 5 erase[i'reis] vt. 抹去, 擦掉L1 6 evaluat ion[i'v✌lju ei☞☜n] n. 评价, 估价L1 eventually[i'v☜nt☞u☜li ] adv.终于L2 1 evolution[ev☜'lu:☞☜n] n.进展L1 6 excecution[eksi'kju:☞☜n] n. 执行, 完成L9 execute ['ekskju:t] v. 执行L8 exerte [i♈'z☜:t] vt. 施加L20 experience[iks'piri☜ns] n. 经验L1 6 explosive[iks'pl☜usiv]adj.爆炸(性)的L2 2 extend[eks'tend] v. 伸展L 2 external[eks't☜:nl] a. 外部的L5,1 1 extract[eks'tr✌kt] v. 拔出L1 4 extreme[iks'tri:m] n. 极端L1 3 extremely[iks'tri:mli] adv. 非常地 L1 2 extremity[iks'tmiti] n. 极端L1 3 extrusion[eks'tru:✞☜n] n. 挤压, 挤出L 3FF (Fahrenheit)['f✌r☜nhait]n.华氏温度L2 fabricate ['f✌brikeit] vt.制作,制造L7 facilitate [f☜'siliteit] vt. 帮助L 6 facility[f☜'siliti] n. 设备L 4 facing[feisi☠] n. 端面车削L 5 fall within 属于, 适合于L1 5 fan[f✌n] n.风扇L7 far from 毫不, 一点不, 远非L9 fatigue[f☜'ti♈] n.疲劳L 1 feasible ['fi:z☜bl] a 可行的L18 feature ['fi:t☞☜] n.特色, 特征L7,17 feed[fi:d] n.. 进给L 5 feedback ['fi:db✌k] n. 反馈L8 female['fi:meil] a. 阴的, 凹形的L1 1 ferrule['fer☜l] n. 套管L1 4 file system 文件系统L9 fitter['fit☜] n.装配工, 钳工L 4 fix[fiks] vt. 使固定, 安装, vi. 固定L1 1 fixed half and moving half 定模和动模L1 1 f l a t-p a n e l t e c h n o l ogy平面(显示)技术L9 f l e xi b i l it y[fleksi'bilit i] n. 适应性, 柔性L9 flexible['fleks☜bl] a. 柔韧的L1 3 flow mark 流动斑点L13 follow-on tool 连续模L18 f o r e go i n g ['f :'♈☜ui☠]adj. 在前的,前面的L8 f o r e t e l l[f :'t ell] vt. 预测, 预示, 预言L9 forge[f :d✞] n. v. 锻造L 3 forming[f :mi☠] n. 成型L 3 four screen quadrants 四屏幕象限L9 fracture['fr✌kt☞☜] n.破裂L2 1124free from 免于L2 1Ggap[♈✌p] n. 裂口, 间隙L10 gearbox['♈i☜b ks] n.齿轮箱L 5 general arrangement L1 6 govern['♈✈v☜n] v.统治, 支配, 管理 L1 3 grain [♈rein] n. 纹理L20 graphic ['♈r✌fik] adj. 图解的L 6 grasp [♈r✌sp] vt. 抓住L8 grid[♈rid] n. 格子, 网格L1 6 grind[♈raind] v. 磨, 磨削, 研磨L 3 gr i n d i n g ['♈raindi☠] n. 磨光,磨削L3,20 grinding machine 磨床L 5 gripper[♈rip☜] n. 抓爪, 夹具L9 groove[♈ru:v] n. 凹槽L1 2 guide bush 导套L 5 guide pillar 导柱L 5 guide pillars and bushes 导柱和导套L1 1Hhandset['h✌ndset] n. 电话听筒L 4 hardness['ha:dnis] n.硬度L1, 2 hardware ['ha:dw☪☜] n. 硬件L 6 h e a d s t o c k['h e d s t k] n.床头箱, 主轴箱L5 hexagonal[hek's✌♈☜nl] a. 六角形的, 六角的L1 1 h i n d r a n c e['h i n d r☜ns] n.障碍, 障碍物L11 hob[h b] n. 滚刀, 冲头L 4 hollow-ware 空心件L2 1 horizontal[h ri'z ntl] a. 水平的L1 6 hose[h☜uz] n. 软管, 水管L1 3 hyperbolic [haip☜'b lik] adj.双曲线的L7Ii.e. (id est) [拉] 也就是L1 2 identical[ai'dentikl] a同样的L1 6 identify [ai'dentifai] v. 确定, 识别L7 idle ['aidl] adj.空闲的L8 immediately[i'mi:dj☜tli] adv. 正好, 恰好L1 2 impact['imp✌kt] n.冲击L 1 impart [im'pa:t] v.给予L11,17 implement ['implim☜nt] vt 实现L 6 impossibility[imp s☜'biliti] n.不可能L2 1 impression[im'pre☞☜n] n. 型腔L1 1 in contact with 接触L 1 in terms of 依据L 1 inasmuch (as)[in☜z'm✈t☞] conj.因为, 由于L 3 inch-to-metric conversions 英公制转换L7 inclinable [in'klain☜bl] adj. 可倾斜的L20 inclusion [in'klu☞☜n] n. 内含物L19 inconspicuous[ink☜n'spikju☜s] a. 不显眼的L1 4 incorp orat e [in'k :p☜reit] v 合并,混合L17 indentation[ inden'tei☞☜n ] n.压痕L 1 indenter[in'dent☜] n. 压头L 1 independently[indi'pein☜ntli] a. 独自地, 独立地L1 6 inevitably[in'evit☜bli] ad. 不可避免地L1 4 inexpensive[inik'spensiv]adj. 便宜的L 2 inherently [in'hi☜r☜ntli] adv.固有的L7 injection mould 注塑模L1 1 injection[in'd✞ek☞☜n] n. 注射L1 1 in-line-of-draw 直接脱模L1 4 insert[in's☜:t] n. 嵌件L1 6 inserted die 嵌入式凹模L19 inspection[in'spek☞☜n] n.检查,监督L9 installation[inst☜'lei☞☜n] n. 安装L10 integration [inti'♈rei☞☜n] n.集成L 6 intelligent[in'telid✞☜nt]a. 智能的L9 intentinonally [in'ten☞☜n☜li] adv 加强地，集中地L17 interface ['int☜feis] n.. 界面L 6 internal[in't☜:nl] a. 内部的L1, 5 int erp olat ion [int☜p☜'lei☞☜n] n.插值法L7 investment casting 熔模铸造L 4125irregular [i'regjul☜] adj. 不规则的，无规律L17 irrespective of 不论, 不管L1 1 irrespective[iri'spektiv] a. 不顾的, 不考虑的L1 1 issue ['isju] vt. 发布，发出L 6Jjoint line 结合线L1 4Kkerosene['ker☜si:n] n.煤油L10 keyboard ['ki:b :d ] n. 健盘L 6 knock [n k] v 敲，敲打L17Llance [la:ns] v. 切缝L19 lathe[lei❆] n. 车床L 4 latitude ['l✌titju:d] n. 自由L17 lay out 布置L1 3 limitation[limi'tei☞☜n] n.限度,限制,局限(性)L 3 local intelligence局部智能L9 locate [l☜u'keit] vt. 定位L18 logic ['l d✞ik] n. 逻辑L7 l ongit udinal['l nd✞☜'t ju:dinl] a. 纵向的L5 longitudinally['l nd✞☜'tju:dinl] a. 纵向的L1 3 look upon 视作, 看待L17 lubrication[lju:bri'kei☞☜n ] n.润滑L2 1Mmachine shop 车间L 2 machine table 工作台L8 machining[m☜'☞i:ni☠] n. 加工L 3 made-to-measure 定做L1 5 m a i n t e n a n c e['m eint in☜ns] n.维护,维修L7 majority[m☜'d✞a:riti] n.多数L2 1 make use of 利用L 2 male[meil] a. 阳的, 凸形的L1 1 malfunction['m✌l'f✈☠☞☜n] n. 故障L9 mandrel['m✌dtil] n.心轴L2 2manifestation[m✌nif☜s'tei☞☜n] n. 表现, 显示L9 m a s s i v e n e s s['m✌sivnis ] 厚实，大块L19 measure['me✞☜] n. 大小, 度量L 1 microcomputer 微型计算机L9 microns['maikr n] n.微米L10 microprocessor 微处理器L9 mild steel 低碳钢L17 milling machine 铣床L 4 mineral['min☜r☜l] n.矿物, 矿产L 2 minimise['minimaiz] v.把···减到最少, 最小化L1 3 minute['minit] a.微小的L10 mirror image 镜像L1 6 mirror['mir☜] n. 镜子L1 6 MIT (Massachusetts Institute of Technology) 麻省理工学院L7 moderate['m d☜rit]adj. 适度的L1, 2 modification [m difi'kei☞☜n ] n. 修改, 修正L 6 modulus['m djul☜s] n.系数L 1 mold[m☜uld] n. 模, 铸模, v. 制模, 造型L 3 monitor ['m nit☜ ] v. 监控L 6 monograph['m n☜♈ra:f] n. 专著L 4 more often than not 常常L20 motivation[m☜uti'vei☞☜n] n. 动机L9 mould split line 模具分型线L1 2 moulding['m☜udi☠] n. 注塑件L5,1 1 move away from 抛弃L17 multi-imprssion mould 多型腔模L1 2Nnarrow['n✌r☜u] a. 狭窄的L1 2 NC (numerical control ) 数控L7 nevertheless[ nev☜❆☜'les] conj.,adv.然而,不过L1 1 nonferrous['n n'fer☜s] adj.不含铁的, 非铁的L 2126normally['n :mli]adv.通常地L2 2 novice['n vis] n. 新手, 初学者L1 6 nozzle['n zl] n. 喷嘴, 注口L1 2 numerical [nju'merikl] n. 数字的L 6Oobjectionable [☜b'd✞ek☞☜bl] adj. 有异议的，讨厌的L17 observe[☜b'z☜:v] vt. 观察L 2 obviously [' bvi☜sli] adv 明显地L17 off-line 脱机的L 6 on-line 联机L9 operational [ p☜'rei☞☜nl] adj.操作的, 运作的L8 opportunity[ p☜'tju:niti] n. 时机, 机会L1 3 o p p osing[☜'p☜uz i☠] a.对立的, 对面的L12 opposite[' p☜zit] n. 反面L1a.对立的,对面的L1 2 op t imiz at ion [ p t imai'z ei☞☜n] n.最优化L6 orient [' :ri☜nt] vt. 确定方向L8 orthodox [' : ☜d ks] adj. 正统的，正规的L19 o v e r a l l['☜uv☜r :l] a.全面的,全部的L8,13 overbend v.过度弯曲L20 overcome[☜uv☜'k✈m] vt.克服, 战胜L10 overlaping['☜uv☜'l✌pi☠] n. 重叠L 4 overriding[☜uv☜'raidi☠] a. 主要的, 占优势的L1 1Ppack[p✌k] v. 包装L 2 package ['p✌kid✞] vt.包装L7 pallet ['p✌lit] n.货盘L8 panel ['p✌nl] n.面板L7 paraffin['p✌r☜fin] n. 石蜡L10 parallel[p✌r☜lel] a.平行的L 5 penetration[peni'trei☞☜n ] n.穿透L 1 peripheral [p☜'rif☜r☜l] adj 外围的L 6 periphery [p☜'rif☜ri] n. 外围L18 permit[p☜'mit] v. 许可, 允许L1 6 pessure casting 压力铸造L 4 pillar['pil☜] n. 柱子, 导柱L5,17 pin[pin] n. 销, 栓, 钉L5,17 pin-point gate 针点式浇口L1 2 piston ['pist☜n] n.活塞L 1 plan view 主视图L1 6 plasma['pl✌zm☜] n. 等离子L9 plastic['pl✌stik] n. 塑料L 3 platen['pl✌t☜n] n. 压板L1 2 plotter[pl t☜] n. 绘图机L9 plunge [pl✈nd✞] v翻孔L18 plunge[pl✈nd✞] v.投入L 2 plunger ['pl✈nd✞☜ ] n. 柱塞L19 pocket-size 袖珍L9 portray[p :'trei] v.描绘L2 1 pot[p t] n.壶L2 1 pour[p :] vt. 灌, 注L2 2 practicable['pr✌ktik☜b] a. 行得通的L1 4 preferable['pref☜r☜bl] a.更好的, 更可取的L 3 preliminary [pri'limin☜ri] adj 初步的，预备的L19 press setter 装模工L17 p r e s s[p r e s]n.压,压床,冲床,压力机L2,8 prevent [pri'vent] v. 妨碍L20 primarily['praim☜rili] adv.主要地L 4 procedure[pr☜'si:d✞☜] n.步骤, 方法, 程序L2,1 6 p roduct ivit y.[p r☜ud✈k't ivit i] n. 生产力L9 profile ['pr☜ufail] n.轮廓L10 progressively[pr☜'♈resiv] ad.渐进地L1 5 project[pr☜'d✞ekt] n.项目L 2 project[pr☜'d✞ekt] v. 凸出L1 1 projection[pr☜'d✞ek☞☜n] n.突出部分L2 1 proper['pr p☜] a. 本身的L10 property['pr p☜ti] n.特性L 1 prototype ['pr☜ut☜taip] n. 原形L7127proximity[pr k'simiti] n.接近L9 prudent['pru:d☜nt] a. 谨慎的L1 6 punch [p✈nt☞] v. 冲孔L 3 punch shapper tool 刨模机L17 punch-cum-blanking die 凹凸模L18 punched tape 穿孔带L 3 purchase ['p☜:t☞☜s] vt. 买，购买L 6 push back pin 回程杆L 5 pyrometer[pai'n mit☜] n. 高温计L 2Qquality['kwaliti] n. 质量L1, 3 quandrant['kw dr☜nt] n. 象限L9 quantity ['kw ntiti] n. 量，数量L17 quench[kwent☞] vt. 淬火L 2Rradial['reidi☜l] adv.放射状的L2 2 ram [r✌m] n 撞锤. L17 rapid['r✌pid]adj. 迅速的L 2 rapidly['r✌pidli]adv. 迅速地L 1 raster['r✌st☜] n. 光栅L9 raw [r :] adj. 未加工的L 6 raw material 原材料L 3 ream [ri:m] v 铰大L17 reaming[ri:mi☠] n. 扩孔, 铰孔L8 recall[ri'k :l] vt. 记起, 想起L1 3 recede [ri'si:d] v. 收回, 后退L20 r e c e s s[r i's e s]n. 凹槽,凹座,凹进处L4,18 redundancy[ri'd✈nd☜nsi] n. 过多L9 re-entrant 凹入的L1 2 r e f e r[r i'f☜:]v.指, 涉及, 谈及L1,12 reference['ref☜r☜ns] n.参照,参考L2 1 refresh display 刷新显示L9 register ring 定位环L1 1 r e gi s t e r['red✞st☜] v. 记录, 显示, 记数L2 regrind[ri:'♈aind](reground[ri:'gru:nd]) vt. 再磨研L1 2 relative['rel☜tiv] a. 相当的, 比较的L1 2 relay ['ri:lei] n. 继电器L7 release[ri'li:s] vt. 释放L1relegate['rel☜geit] vt. 把··降低到L9 reliability [rilai☜'biliti] n. 可靠性L7 relief valves 安全阀L2 2 relief[ri'li:f] n.解除L2 2 relieve[ri'li:v ]vt.减轻, 解除L 2 remainder[ri'meind☜] n. 剩余物, 其余部分L 4 removal[ri'mu:vl] n. 取出L1 4 remove[ri'mu:v] v. 切除, 切削L 4 reposition [rip☜'zi☞☜n] n.重新安排L17 represent[ repri'zent☜] v 代表,象征L1 1 reputable['repjut☜bl] a. 有名的, 受尊敬的L1 5 reservoir['rez☜vwa: ] n.容器, 储存器L2 2 resident['rezid☜nt] a. 驻存的L9 resist[ri'zist] vt.抵抗L 1 resistanc e[ri'zist☜ns] n.阻力, 抵抗L1 resolution[ rez☜'lu:☞☜n] n. 分辨率L9 r e s p e c t i v e[ri'sp ekt iv] a.分别的,各自的L11 respond[ris'p nd] v.响应, 作出反应L9 responsibility[risp ns☜'biliti] n.责任L1 3 restrain[ris'trein]v.抑制L2 1 restrict [ris'trikt] vt 限制，限定L18 restriction[ris'trik☞☜n] n. 限制L1 2 retain[ri'tein] vt.保持, 保留L2,1 2 retaining plate 顶出固定板L1 6 reveal [ri'vil] vt.显示，展现L17 reversal [ri'v☜sl] n. 反向L1,20 right-angled 成直角的L20 rigidity[ri'd✞iditi] n. 刚度L 1 rod[r d] n. 杆, 棒L1, 5 rotate['r☜uteit] vt.(使)旋转L 5 rough machining 粗加工L 5 rough[r✈f] a. 粗略的L5,2 1 routine [ru:'ti:n] n. 程序L7 rubber['r✈b☜] n.橡胶L3,2 2 runner and gate systems 流道和浇口系统128L1 1Ssand casting 砂型铸造L 3 satisfactorily[ s✌tis'f✌ktrili] adv. 满意地L 1 saw[a :] n. 锯子L 4 scale[skeil]n. 硬壳L 2 score[sk :] v. 刻划L1 4 s c r a p[s k r✌p]n.废料,边角料, 切屑L2,3 screwcutting 切螺纹L 4 seal[si:l] vt.密封L2 2 secondary storage L9 section cutting plane 剖切面L1 6 secure[si'kju☜] v.固定L2 2 s e c u r e[s i'kju☜] vt.紧固,夹紧,固定L5,22 segment['se♈m☜nt] v. 分割L10 sensitive['sensitiv]a.敏感的L1,7 sequence ['si:kw☜ns] n. 次序L 6 sequential[si'kwen☞☜l] a.相继的L1 6 seriously['si☜ri☜sli] adv.严重地L 1 servomechanism ['s☜:v☜'mek☜nizm] n.伺服机构L7 Servomechanism Laboratoies 伺服机构实验室L7 servomot or ['s☜:v☜m☜ut☜] n.伺服马达L8 setter ['set☜] n 安装者L17 set-up 机构L20 sever ['sev☜] v 切断L17 severity [si'veriti] n. 严重L20 shaded[☞✌did] adj.阴影的L2 1 shank [☞✌☠k] n. 柄. L17 shear[☞i☜]n.剪,切L 1 shot[☞t] n. 注射L1 2 shrink[☞ri☠k] vi. 收缩L1 1 side sectional view 侧视图L1 6 signal ['si♈nl] n.信号L8 similarity[simi'l✌riti] n.类似L1 5 simplicity[sim'plisiti] n. 简单L1 2 single-point cutting tool 单刃刀具L 5 situate['sitjueit] vt. 使位于, 使处于L1 1 slide [slaid] vi. 滑动, 滑落L20 slideway['slaidwei] n. 导轨L 5 slot[sl t] n. 槽L 4 slug[sl✈♈] n. 嵌条L1 2 soak[s☜uk] v. 浸, 泡, 均热L 2 software ['s ftw☪☜] n. 软件L 6 solid['s lid] n.立体, 固体L9 solidify[s☜'lidifai] vt.vi. (使)凝固, (使)固化L1 3 solution[s☜'lu:☞☜n] n.溶液L 2 sophisiticated [s☜'fistikeitid] adj.尖端的,完善的L8 sound[saund] a. 结实的, 坚固的) L 1 spark erosion 火花蚀刻L10 spindle['spindl] n. 主轴L5,8 spline[splain] n.花键L 4 split[split] n. 侧向分型, 分型L12,1 4 spool[spu:l] n. 线轴L1 4 springback n.反弹L20 spring-loaded 装弹簧的L18 sprue bush 主流道衬套L1 1 sprue puller 浇道拉杆L1 2 square[skw☪☜] v. 使成方形L 4 stage [steid✞] n. 阶段L16,19 standardisation[ st✌nd☜dai'zei☞☜n] n. 标准化L1 5 startling['sta:tli☠] a. 令人吃惊的L10 steadily['sted☜li ] adv. 稳定地L2 1 step-by-step 逐步L8 stickiness['stikinis] n.粘性L2 2 stiffness['stifnis] n. 刚度L 1 stock[st k] n.毛坯, 坯料L 3 storage tube display 储存管显示L9 storage['st :rid✞] n. 储存器L9 s t r aight forward[st reit'f :w☜d]a.直接的L10 strain[strein] n.应变L 1129strength[stre☠] n.强度L 1 stress[stres] n.压力,应力L 1 stress-strain应力--应变L 6 stretch[stret☞] v.伸展L1,2 1 strike [straik] vt. 冲击L20 stringent['strind✞☜nt ] a.严厉的L2 2 stripper[strip☜] n. 推板L1 5 stroke[strouk] n. 冲程, 行程L1 2 structrural build-up 结构上形成的L1 1 sub-base 垫板L19 subject['s✈bd✞ikt] vt.使受到L2 1 submerge[s☜b'm☜:d✞] v.淹没L2 2 subsequent ['s✈bsikwent] adj. 后来的L20 subsequently ['s✈bsikwentli] adv. 后来, 随后L 5 substantial[s☜b'st✌n☞☜l] a. 实质的L10 substitute ['s✈bstitju:t] vt. 代替,.替换L7 subtract[s☜b'tr✌kt] v.减, 减去L1 5 s u i t a b l e['s u:t☜b l] a. 合适的, 适当的L5 suitably['su:t☜bli] ad.合适地L1 5 sunk[s✈☠k](sink的过去分词) v. 下沉, 下陷L1 1 superior[s☜'pi☜ri☜] adj.上好的L2 2 s u scep t ible[s☜'sep t☜bl] adj.易受影响的L7 sweep away 扫过L17 symmetrical[si'metrikl] a. 对称的L1 4 s y n c hroniz e ['si☠kr☜naiz] v.同步,同时发生L8Ttactile['t✌ktail] a. 触觉的, 有触觉的L9 tailstock['teilst k] n.尾架L 5 tapered['teip☜d] a. 锥形的L1 2 tapping['t✌pi☠] n. 攻丝L8 technique[tek'ni:k] n. 技术L1 6 tempering['temp☜r☠] n.回火L 2 tendency['tend☜nsi] n. 趋向, 倾向L1 3 t ensile['tensail] a.拉力的, 可拉伸的L2 拉紧的, 张紧的L 1 tension ['ten☞☜n] n.拉紧,张紧L 1 terminal ['t☜:m☜nl ] n. 终端机L 6 terminology[t☜:mi'n l☜d✞i ] n. 术语, 用辞L1 1 theoretically [ i:☜'retikli ] adv.理论地L2 1 thereby['❆☪☜bai] ad. 因此, 从而L1 5 t hermoplastic[' ☜:m☜u'pl✌stik] a. 热塑性的, n. 热塑性塑料L 3 thermoset[' ☜:m☜set] n.热固性L1 2 thoroughly[' ✈r☜uli] adv.十分地, 彻底地L 2 thread pitch 螺距L 5 thread[ red] n. 螺纹L 5 thrown up 推上L17 tilt [tilt] n. 倾斜, 翘起L20 tolerance ['t l☜r☜ns] n..公差L17 tong[t ☠] n. 火钳L 2 tonnage['t✈nid✞] n.吨位, 总吨数L 3 tool point 刀锋L 3 tool room 工具车间L10 t o o l h o l d e r['t u:lh☜uld☜] n.刀夹,工具柄L5 t o o l m a k er ['t u:l'meik☜] n 模具制造者L17 toolpost grinder 工具磨床L 4 toolpost['tu:l'p☜ust] n. 刀架L 4 torsional ['t :☞☜nl] a扭转的. L 1 toughness['t fnis] n. 韧性L 2 trace [treis] vt.追踪L7 tracer-controlled milling machine 仿形铣床L 4 transverse[tr✌ns'v☜:s] a. 横向的L 5 tray [trei] n. 盘，盘子，蝶L19 treatment['tri:tm☜nt] n.处理L 2 tremendous[tri'mend☜s] a. 惊人的, 巨大的L9 trend [trend] n.趋势L7 trigger stop 始用挡料销L17 tungsten['t✈☠st☜n] n.钨L10 turning['t☜:ni☠] n.车削L4, 5130模具英语词汇表131twist[twist ] v.扭曲，扭转 L 1 two-plate mould 双板式注射模L 12 Uultimately['✈ltimitli] adv 终于. L 6 undercut moulding 侧向分型模 L 1 4 undercut['✈nd ☜k ✈t] n. 侧向分型 L 1 4 undercut['✈nd ☜k ✈t] n.底切 L 1 2 underfeed['✈nd ☜'fi:d] a, 底部进料的 L 15 undergo[✈nd ☜'♈☜u] vt.经受L 1 underside['✈nd ☜said] n 下面,下侧L1 1 u n d u e [✈n 'd j u :] a.不适当的, 过度的 L4,10 uniform['ju:nif :m] a.统一的, 一致的 L 12 utilize ['ju:tilaiz] v 利用L17Utopian[ju't ☜upi ☜n] adj.乌托邦的, 理想化的L 2 1 Vvalve[v ✌lv] n.阀L22vaporize['veip ☜raiz] vt.vi. 汽化, (使)蒸发L10 variation [v ☪☜ri'ei ☞☜n] n. 变化L 20v a rious ['v ☪☜ri ☜s] a.不同的,各种的 L1,20 vector feedrate computation 向量进刀速率计算L 7 vee [vi:] n. v 字形L 20 velocity[vi'l siti] n.速度L1versatile['v ☜s ☜tail] a.多才多艺的,万用的L5,8 vertical['v ☜:tikl] a. 垂直的 L 16 via [vai ☜] prep.经,通过 L 8 vicinity[v ☜'siniti] n.附近L 1 3 viewpoint['vju:p int] n. 观点L 4 Wwander['w nd ☜] v. 偏离方向 L 1 3 warp[w :p] v. 翘曲 L 2 washer ['w ☞☜] n. 垫圈L 18 wear [w ☪☜] v.磨损 L 7 well line 结合线L1 3 whereupon [hw ☪☜r ☜'p n] adv. 于是 L19 winding ['waindi ☠] n. 绕, 卷 L 8 with respect to 相对于 L 1,5 w i t h s t a n d [w i ❆'s t ✌n d ] vt.经受,经得起 L1work[w ☜:k] n. 工件 L 4 workstage 工序L 19 wrinkle['ri ☠kl] n.皱纹vt.使皱L 2 1 Yyield[ji:ld] v. 生产L 9 Zzoom[zu:] n. 图象电子放大L9。

模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。

L：分模线EJECT PIN/E。

P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：淬火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩水DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期注塑英语型厚大小Thick size锁模结构（机绞/直压）Mode locking structure(machine twists/straight pressure)最大开模距离The biggest die sinking is away from动模板最大模具重量Moves the template maximum mold weight哥林柱间距Elder brother forest column spacing顶出形式（电动五点，油压五点，油压十三点）Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots)顶出长度Goes against the length顶棍孔直径Goes against the stick hole diameter顶棍孔中心矩Goes against the stick hole central moment螺杆材质（合金）Screw rod material quality (alloy)螺杆转速Screw rod rotational speed最大射出体积Projects the volume most greatly最大射出量Projects the quantity most greatly射出率Ejection rate每10mm射出量（理论）Each 10mm projects the quantity (theory)射咀直径Shoots ju the diameter射咀R值Shoots ju the R value射咀空径Shoots ju the spatial diameter定位环直径Locating ring diameter溶胶能力Sol ability驱动方式（全自动/全液压）Drive type (completely automatic/entire hydraulic pressure)电压Voltage电热功率Electric heating power电机功率Electrical machinery power作动油量Does moves the oil mass机械尺寸Mechanical size机械重量Mechanical weight最高溶胶温度Highest sol temperature是否带中子Whether to bring the neutron是否带吹气Whether to have the air flus开模行程，open ould stroke定产，order production定产效率，efficiency of order prod uction注胶切换点，glue-injection switching point保压压力1，protective pressure倒索，inverse sling模保护，mould protection关模低压，close mould low pressure炮筒温度，gun barrel temperature回料量，returning amount注射压力，injecting pressure色母配比，raw color ratio mixing配套摸具，matched mold顶针次数，thimble times立式注胶机vertical injector工艺卡，WSP(work specification procedure)工作指导work instr uction注塑机部分英语钣金machine cover / upper cover/ side cover锁模部分clamping unit射胶部分injection unit机架machine frame / base电气系统electric system液压系统hydraulic system机械系统mechanical system机门safety door / fixed door / movable door锁模部分clamping unit电脑控制器computer controller机械安全锁mechanical safety interlock射胶部分injection unit液压系统hydraulic system电箱electrical cabinet / cable机架分体线stand split line机架螺丝孔foundation bolt hole机架machine base / supporting frame理论注射容积theoretical shot volume实际注射量shot weight螺杆直径screw diameter注射压力injection pressure注射速度injection speed注射速率injection rate螺杆长径比screw L/D ratio螺杆行程screw stroke螺杆转速screw speed熔胶能力plasticizing capacity锁模力clamping force开模/锁模行程mold clamping / opening stroke模板尺寸platen size拉杆间距distance between tie bars / rods模板最大距离max. daylight容模量mold thickness (min. & max.)顶出行程hydraulic ejection stroke顶出力hydraulic ejection force顶针数nos. of ejector pin液压系统压力hydraulic system pressure油泵马达pump motor电热量heating capacity温度控制区数nos. of temp control zones射嘴接触力nozzle contact forceInjection 注射Mould closing 关模Cooling time冷却时间Holding time 保压时间Injection start delay 注射延迟Injection alarm time注射报警时间Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压Screwvalue for change-over to holding加料Hydraulic pressure in holding锁模力Filling stage pressure limit充模压力Injection speed注射速度Plasticizing delay预塑延时1st suck-back speed储料一速度1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点Decompression value at end of plasticizing预塑终点Mould close force关模压力Mould closing safety time .. 时间Mould closing pressure .. 压力1st closing safety stage pressure 合模一段压力1st mould closing speed ...成型速度1st stage mould closing safety position.....位置High pressure start position高压锁模位置注塑专业英语Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡Void孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to 产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in e xtra …添加多一点…Reduced … content减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption预计年/月用量--- 详细信息1. 注射模具名称注射模：Injection mould热塑性塑料注射模：Injection mould for thermoplasctics 热固性塑料注射模：Injection mould for thermosets无流道模：Runerless mould热流道模：Hot runner mould绝热流道模：Insulated温流道模：Warm runner mould2. 浇注，排溢，分型浇注系统：Feed system主流道：Sprue分流道：Runner浇口：Gate直接浇口：Direct gate ;Sprue gate环行浇口：Ring gate盘型浇口：Disk gate ;Diaphragm轮辐浇口：Spoke gate :Spider gate点浇口：Pin-point gate侧浇口：Edge gate潜伏浇口：Submarine gate护耳浇口：Tab gate扇型浇口：Fan gate 牛角浇口：Horn gate冷料穴：Cold-slug well浇口套：Sprue bush ;Sprue bushing浇口镶块：Gating insret分流锥：Sprader流道板：Runner plate热流道板：Manifold block;Hot-runner manifold温流道板：Warm runner plate二级喷嘴：Secondary nozzle鱼雷形组合体：Torpedo;Torpedo body assembly管式加热器：Cartridge heater热管：Heat pipe阀式浇口：Valve gate加热腔：Loading chamber柱塞：Force plunger;Pot plungr溢料槽：Flash grorve ;Spew grovve排气槽：Vent分型面：Parting line水平分型面：Horizontal parting half垂直分型面：Vertical parting half3. 成型零件定模：Stationary mould:Fixed half动模；Movable mould ;Moving half上模:Upper mould;Upper half下模：Lower mould :Lower half型腔：Cavity凹模：Impression;Cavity plate镶件：Mould insert活动镶件：Movable insert;Lose detail拼块：Splits凹模拼块：Cavity splits型芯拼块：Core splits型芯：Core侧型芯：Side core:slide core螺纹型芯：Thread plug;Threaded core螺纹型环：Thread ring;Threaded cavity凸模：Punch;Force嵌件：Insert for mould4. 支持与固定零件定模座板：Fixed clamp plate:Top clamping plate;Top plate动模座板：Moving clamp plate :Bottom clamping plate; Bottm plate 上模座板：Upper clamping plate下模座板：Lower clamping plate凹模固定板：Cavity-retaier plate型芯固定板：Core-retaier plate凸模固定板：Punch-retaier pilte模套：Chase ;Bolster;Frame;支撑板：Backing plate垫块：Spacer parallel支架：Ejector housing支撑柱：Support pillar模板：Mould plate5. 抽芯零件斜销：Angle pin; Finger cam滑块：Slide;Cam slide侧型芯滑块：Slide core-slide滑块导板：Slide guide strip锲紧块：Heel block;Wedge block;Locking heel斜槽导板：Finger guide plate弯销：Dog-leg cam斜滑块：Angled-lift splits6. 导向零件导柱：Guide pillar;Guide pin;Leader pin带头导柱：Guide pillar ;Straight leader pin带肩导柱：Guide pillar Shouldered;Shoulder leader pin推板导柱：Ejector guide pillar;Ejeector guide pin导套：Guide bush ;Guide bushing直导套：Guide bush ;Straight ;Straight bushing带头导套：Guide bush ;Shoulder bushing推板导套：Ejector guide bush;Ejector bushing7. 定位和限位零件定位圈：Locating ring锥形定位圈：Mould bases locating elements复位杆：Ejector plate return pin;Push-back pin限位钉：Stop pin;Stop button限位块：Stop block ;Stop pad定距拉杆：Length bolt;Puller bolt定距拉板：Puller plate;Limit plate8. 推出零件推杆：Ejector pin圆柱头推杆：Ejector pin with cytindrical head带肩推杆:Shouldered ejector pin扁推杆:Flar ejector pin推管：Ejector sleeve推块：Ejector pad推件板：Stripper plate推件环：Stripper ring;Stripper dlisk推杆固定板：Ejector retainer plate推板：Ejector plate;Ejection plate连接推杆：Ejector tie rod 拉料杆：Sprue puller钩形垃料杆：Sprue puller ;Z-shaped球头垃料杆：Sprue puller;Ball headed圆锥头垃料杆：Sprue puller;Conical headed分流道垃料杆：Runner puller;Runner lock pin推流道板：Runner stripper plate9. 冷却和加热零件冷却通道：Cooling channel;Cooling line隔板：Baffle加热板：Heating plate隔热板：Thermal insulation board10. 模架模架：Mould base标准模架：Standard mould base11. 塑料成型模具的主要设计要素注射能力：Shot capacity收缩率：Shrinkage注射压力：Injection pressure锁模力：Clamping force ;Locking force成型压力：Moulding pressure模内压力：Internal mould pressure;Cavity pressure 开模力：Mould opening force脱模力：Ejection force抽芯力：Core-pulling force抽芯距：Core-pulling distance闭合高度：Mould shut height最大开距：Maximum daylight;Open daylight投影面积：Projected area脱模斜度：Draft脱模距：Stripper distance。

模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance叮叮小文库热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket四、模具零件：mold components三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin叮叮小文库司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder叮叮小文库液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture叮叮小文库证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。

Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。

汽车冲压模具英语词汇Die / Tool= 模具Prog. Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套Casting die=铸造模Cage=套Part=钣件Rigidity=强度Die material=制模材料Thin=薄Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”Tool design approval=模具设计审核Tool design modification/revision=模具设计更改Tool parts design (detail) = 模具钣件设计（详细）Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引FMC Make=保丽龙制作Construction method=结构方法modification= 更改Check & measure=检查& 测试Machining= 机器加工Large machining=在大型机器上加工上下模架（铣、车等）Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块Lower trim inserts retainer=下模切刃块承盘Assemble inserts=组立镶块Punch stripping plates=冲头压料板Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块Fitting=研磨组立Spotting=合模Die tryout=试模Cushing stroke=缓冲行程Dowel pin=定位销Guide lift pin=导引升降销Assemble gas spring=安装氮气缸Stamp parts=冲钣件Adjustment=调试Run off parts=冲钣件Lower trim steels=下刃块Hit parts=冲钣件Section=冲头断面Lifters=提升器Trim punch=切刃冲头Coil=卷材jack screw hole=起重[千斤顶]螺旋孔Guide block=导引块Die set, lower plate=下模架Guide the coil through the tool=导引卷材Die set, upper plate=上模架layout inspection=全尺寸检验Die inspection & approval=模具检查和审核Stretch carriers=拉伸运送装置delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托stop block=停止块Prepare for delivery=准备发货Hydro form 液压成形Key=键Shear=剪切For locating retainer blocks=承盘键Sensor=传感器For holding buttons or pilots=冲母座或导销键Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷材Spotting red=合模用丹红Checking aid /checking gage=检具Layout ink=试模用蓝墨水Jig=夹具Masking tape=黄色不透明胶带(遮蔽胶带) Fixture=夹具Pliers=尖嘴钳，老虎钳Ball bearing guide posts and bushings=球形滚珠轴套Cresent wrench=可调扳手Guide post=导柱Bushings=导套Pump pipe=泵管Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪Symmetric=对称的The axis of symmetry=对称轴Technical=技术上的Diagonal=对角线Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块Granite Table=花岗岩平台Backing Plate=背板Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记器, 标图员Shoulder Bolt=肩头螺丝(Stripper bolt)Belt Sander=带磨机Keeper Block=行程块Metal Cutting Band Saw=立式带锯床Corner Guide Block=导块Blanchard Grinder=大型平面磨床Dowel pin=定位销Joe Blocks=精密量块Set Screw=螺塞Whirly Gig=筒夹式冲子成形器Jig & fixture =夹具Chamfer Tools=倒角刀具组Checking fixture=检具Angle Plate=L形直角座Guide Block=导块Gage Pins=英寸塞规Plunger=柱塞Sine Plate (magnetic)=正弦磁台Pierce=冲孔Flute End Mill=硬质合金钢铣刀Wear Strip=耐磨板Mill Cutter=波纹粗铣刀（标准型）Mating area=组立的接触面C’bore/ counter bore=六角沉头铣刀Accommodate=适应Radius Dresser=砂轮修整器Wiping hard (very shiny)= 过分摩擦闭合[接触]（闪光）Boring Head & Boring Bar=搪孔器、搪刀杆Pin=销Increase the die clearance between the form steels=增加成形块间隙Reamer=绞刀Clearance=间隙Approval=确认Oil paper=油纸Impact wrench=气动扳手0-11” Micrometer=0-11”千分尺Air pin=空气销Trim line=切边bumper[‘bQmpE(r)] n.缓冲器+/-0.5mm unless otherwise specified除非另有规定，否则公差为+/-0.5mmVendor [‘vendE(r), -dC:(r)] n.卖主Part tolerance=钣件公差stripper layout=排样图Ball nose=球刀drawing of panel #987415&16=钣件设计图（公差）Bore=镗Line tap=攻丝校直Arbor =柄轴；心轴Borer=镗刀，镗床Drill chuck=钻夹头Chamfer=倒角Button=冲母座Radius=半径Nitrogen Cylinder=氮气缸Coolant=切削液Pilot=导销Punch=冲头Retainer=承盘Distribution Blocks=接头座Button=冲母座Screw=螺丝Hose Straps=软管夹（塑料）Shop=车间Flat Feet Keepers=顶料销Crib=仓库Ejector Pin=顶出销CNC mill= CNC机床Spring=弹簧Jack=千斤顶Straight Port Adapter=直管接头Strips=料条Y-205 Hose=软管（塑料）Styrofoam [`stairEfEum]n.聚苯乙烯泡沫塑料（保丽龙材料）Short Neck Adapter=短接头Cut off=落料45。