air drier 空气干燥器-Membrane

Why dry yourcompressed air?Compressed air contains oil, solid particles and water vapors. It is theinherent result of the compression process, which concentrates thenatural water vapors and particles in the air that surrounds us. Thisuntreated compressed air poses a substantial risk to your air system andend products. Its moisture content alone can cause corrosion in pipework, premature failure of pneumatic equipment, product spoilageand more. An air dryer is therefore essential to protect your systemsand processes.Refrigerant dryersby Atlas CopcoAtlas Copco’s refrigerant dryers provide the clean, dry air you need+) to expand the life of your equipment and ensure the quality of yourproducts. Our FD and FX dryers are designed in-house and tested usingthe most stringent methods. They meet or exceed the internationalstandards for compressed air purity and are tested according toISO 7183:2007.253614Controls the speed of the compressor to match your air demand and ensure the highest possible energy savings.1Opens the drain only when needed to eliminate unnecessary loss of compressed air during timed draining.4Counter-flow compact brazed plate or aluminum heat exchanger, with air-to-air side for optimum cooling efficiency and the lowest possible pressure drop.2®Touch controllerProvides advanced control and allows for remote monitoring.5Low velocity with high separation efficiency, even in low flow conditions.3Ensures plug-and-play installation.6VSD for superior energy savingsAtlas Copco’s in-house developed VSD technology matches your FD dryer’s power consumption to your production’s actual airflow. While a traditional refrigerant dryer can only be turned on or off, Atlas Copco’s FD VSD mirrors your production’s demand for compressed air as it fluctuates during the day, week or year. This ensures supreme energy savings as well as a stable dew point.Minimal environmental impactFD VSD dryers use the CFC-free R410A refrigerant, which has an ozone depletion potential (ODP) of zero. The refrigerant meets the strict F-Gas regulations and, due to its low powerconsumption, has an an outstanding TEWI (Total Equivalent Warming Impact) performance.Optimum performance and safety in all conditions• Hot gas bypass valve prevents freezing at lower loads.• The extremely reliable R410A rotary compressor provides the best performance with minimum environmental impact.Capillary tubes cope with all conditions – no moving parts for extra reliability.• Condenser with louvered fin technology for improved performance in dusty environments.Advanced remote monitoring and control• High-tech Elektronikon ® Touch controller with warning indications, dryer shutdown and maintenance scheduling. • Standard SMARTLINK remote monitoring to maximize air system performance and energy savings.Robust and compact design• Forklift opening for smooth transport. • Easy front and side panel access.• No bulky thermal mass heat exchanger needed to save on energy.FiltersIf your production requires higher levels of air quality andfiltration, UD + filters can be added on to your FD VSD dryer.Power consumptionVSD dryerFixed speed dryerSupreme energy efficiency• The FD offers a low pressure drop – typically below 0.2 bar/2.9 psi – and minimal energy consumption.• The compact brazed plate or aluminum heat exchanger was designed specifically to provide optimal pre-cooling and the lowest possible pressure drop.• The electronic no-loss condensate drain comes with a level sensor to open the drain only when needed, preventing unnecessary loss of compressed air.Comprehensive control and monitoring options• The Elektronikon ® Alpha controller displays the pressure dew point and relative humidity.• Remote alarm and start/stop control through voltage-free contact.• Additional features such as alarm history and standard remote visualization.Easy installation and long maintenance intervals• Small footprint thanks to an innovative all-in-one design. • Delivered ready for use, minimizing costly production downtime.Low environmental impactFD dryers use CFC-free refrigerants (R134A and R410A) with an ozone depletion potential (ODP) of zero.Counter-flow compact brazed plate or aluminum heatexchanger, with air-to-air side for optimum cooling efficiency and the lowest possible pressure drop.2condensate drainWith level sensor, backup manual drain and drain alarm.4separatorLasts longer thanks to limited vibrations, minimal moving parts, and reduced risk of leakage.1Reduces energy consumption and optimizes the pressure dew point at very low temperatures.5Low velocity with high separation efficiency even in low flow conditions.3Ensures stable pressure dew point and prevents freezing at lower loads.6connectionAllows for plug-and-play installation.8Eliminates the chance of moisture entering the compressed air system.7Reliable performance in tough conditions• Hot gas bypass valve prevents freezing at lower loads.• R134A piston compressor with high coefficient of performance (extremely reliableR410A rotary compressor for models FD 60-FD 95) provides the best performance with minimum environmental impact. Capillary tubes cope with all conditions – no moving parts for extra reliability.• Condenser with louvered fin technology for improved performance in dusty environments.3748152637481526Pressure dew point precisionThe FX comes in a wide range of sizes (7-300 l/s or 15-636 cfm) to offer a steady pressure dew point as low as +3°C/+37.4°F. Its easy to use digital display precision-measures and monitors the pressure dew point and dryer performance.Digital display• Pressure dew point: exact measurement and visual monitoring. • Status: refrigerant compressor and fan.• Alarms: high/low pressure dew point and probe failure.• Service warning.ReliableBuilt according to the stringent Atlas Copco standards, the FX is made of high quality, generously sized components.Hot environmentsHigh ambient temperatures can put your equipment to the test. The FX range offers several high temperature models that ensure dependable performance in conditions up to 46°C/115°F.Significant cost savings• Increased reliability and lifetime of tools and equipment.• Reduced pipe work leaks and thus a lower energy bill.• Less equipment breakdowns and operational interruptions.• Minimal chance of product damage as a result of moisture carryover.Sustainable refrigerantThe FX range comes with refrigerant that is compliant with F-Gas regulations to ensure the lowest possible carbon footprint and energy consumption.separatorNo chance of moisture entering the compressed air system.1Ensures stable pressure dew point and eliminates the possibility of condensate freezing.2Provides peace of mind through precise monitoring of pressure dew point.3connectionAllows for plug-and-play installation.4componentsFor straightforward servicing.5Offers high efficiency for better pressure dew point.6with integrated liquid separatorLasts longer thanks to limited vibrations, minimal moving parts, and reduced risk of leakage.8For a small footprint.7VSD:a game-changer in energy savingsWhen purchasing a refrigerant dryer, the main focus is usually on the initial cost. However, this only represents approximately 10% of the lifecycle cost of the dryer. Energy, maintenance and installation make up the bulk of your actual dryer costs. Direct and indirect (pressure drop) energy costs are the most important.Indirect energy costsIndirect energy costs are related to the extra energy your aircompressor must consume to overcome the pressure drop that takesplace in the air dryer. By design, Atlas Copco FD VSD dryers offer a lowpressure drop and efficient heat transfer – both of which contribute toFD VSD 100-300:Elektronikon ® Touch controller• 4.3-inch high-definition color display with clear pictograms and service indicator.• Internet-based dryer visualization using a simple Ethernet connection.• Automatic restart after voltage failure.• Built-in SMARTLINK online monitoring.• More flexibility: four different week schedules.• Graphical service plan indication.• Remote control and connectivity functions.SMARTLINK & Total ResponsibilityGet the most out of SMARTLINK as part of a Total Responsibility Plan. Step back, relax, and let our service engineers monitor your compressed air system. We know exactly when to serviceyour machines, diagnose any issues and be there on time to fix them.FD 5-95:Elektronikon ® Alpha controller• Exact measurement and visual monitoring of pressure dew point and ambient temperature.• High/low pressure dew point alarm.• Relative humidity indicator.• Energy saving mode.• Switch off at freezing alarm.• Alarm history and standard remote visualization.FX 1-16: Digital display• Pressure dew point: exact measurement and visual monitoring. • Energy saving mode.• Alarms: high/low pressure dew point and probe failure.•Service warnings.SMARTLINK: Data Monitoring ProgramSMARTLINK captures live data from your compressed air equipment and translates it in clear insights. At a glance, you can check uptime, energy efficiency and machine health.• Remote monitoring that helps you optimize your compressed air system and save energy and costs.• Provides a complete insight in your compressed air network.• Anticipates potential problems by warning you upfront.• Efficient service planning and parts handling to give you improved uptime.Advanced controlAtlas Copco’s refrigerant dryers are built to reliably and efficiently deliver quality air. But in the end, it’s all about how they perform on your work floor, meeting your individual needs and responding to your specific conditions. That is why the FD VSD, FD and FX come with comprehensive control options to allow you to get the best performance from your Atlas Copco dryer.Remote monitoringHow refrigerant dryers workA refrigerant dryer uses a refrigerant circuit and heat exchanger(s) to pre-coolair, refrigerate it to condense out moisture vapor, and then re-heat the air toAir circuit1Air-to-air heat exchanger: Incoming air is cooled downby the outgoing dry, cold air2Air-to-refrigerant heat exchanger: The air is cooled tothe required dew point by the refrigerant circuit. Thewater vapor condenses into water droplets3Integrated water separator: The moisture is collectedand evacuated by the electronic drainRefrigerant circuit4Refrigerant compressor: Compresses the gaseousrefrigerant to a higher pressure5Regulation device: The hot gas bypass valve regulatesthe dryer to prevent freezing at lower load conditions6Refrigerant condenser: Cools the refrigerant so that itchanges from a gas to a liquid7Refrigerant filter: Protects the expansion device fromharmful particles8Thermostatic expansion valve: The expansion processreduces the pressure and cools the refrigerant further9Liquid separator: Ensures that only refrigerant gasenters the compressorHot refrigerant gasCold refrigerant liquidExpanded refrigerant liquid2935 0868 41 © 2020, A t l a s C o p c o A i r p o w e r N V , B e l g i u m . A l l r i g h t s r e s e r v e d . D e s i g n s a n d s p e c i fi c h a n g e w i t h o u t n o t i c e o r o b l i g a t i o n . R e a d a l l s a f e t y i n s t r u c t i o n s i n t h e。

城市轨道交通车辆专业英语COMPONENTS组成：1.Car body车身It is to accommodate passengers and the driver.这是为了容纳乘客和司机。

Meanwhile, it is the basic component to connect to other devices or car bodies.同时，它是连接到其他设备或车身的基本部件。

For the purpose of meeting the strength requirement while keeping the self-weight at its lowest. 为了满足强度要求，同时保持自重最低。

Integrated steel structure or light metal structure is adopted.采用整体式钢结构或轻型金属结构。

It usually comprises of the floor, the roof, sides and end walls.它通常包括地板、屋顶、侧壁和端壁。

2. Bogies转向架Motor and trailer bogies are located between the car body and the track, to drag and guide the vehicles moving along the track.汽车和拖车转向架位于车体与轨道之间，拖曳和引导车辆沿轨道运动。

They cab bear and transfer a variety of load from lines and the car body, easing its dynamic action.他们从线路和车体上承担和传递各种载荷，减轻其动力作用。

It usually comprises of frame, spring suspension, wheel axle box and brake devices, etc.它通常包括车架、弹簧悬架、车轮轴箱和制动装置等。

Parker Balston ® SMART Dryer ™Installation, Operation, and Maintenance ManualModels SMRT5100, SMRT5200, SMRT5300, SMRT5400, SMRT5500, and SMRT5600Figure 1 - Overall Dimensions Model SMRT5400These instructions must be thoroughly read and understood before installing and operating this product. Any modification of the product will result in void -ing the warranty. Failure to operate this product in accordance with the instruc -tions set forth in this manual could jeopardize the safety of the operator. If you have any questions or concerns, please call the Technical Services Department at 800-343-4048, 8AM to 5PM Eastern Time (North America only) or email at: *****************************.Forotherlocations,pleasecontactyourlocal ***************************************************.Model SMRT5300Bulletin TI-5100JModel SMRT5100Model SMRT5200Model SMRT5500Model SMRT5600Location All installation, operation, and maintenance procedures for the Balston SMRT Series Air Dryers should be performed by suitable personnel using reasonable care.Warning: Use PTFE tape on all threaded components . Use of pipe sealants other than PTFE tape will damage the membrane and void the warranty. Please note that pipe dope of any kind is not to be used in the installation of Balston Air Dryers; use only PTFE tape.Warning: Warranty will be void if black iron pipe or other material that will rust or corrode is used between the prefilters and SMART Air Dryer. Do not weld any connec -tions between prefilters and dryer. Use only stainless steel or brass for all piping and fittings between prefilters and SMART Air Dryer.The Balston SMART Series Air Dryers should be mounted on the floor. The vibration free dry -ers should be installed indoors, in an area where the ambient temperature is less than 110°F(43°C) and above 37°F (3°C). Do not install the dryer outdoors if the tempurature mayexceed these limits. Otherwise, a covered outdoor installation is acceptable.A typical compressed air system with a membrane dryer is shown in Figure 2. The ambientair surrounding the compressor should be free of contaminants (e.g. ammonia compounds,chemical solvents, etc.) which can be drawn into the compressed air and damage the dryer.Compressed Air - The compressed air supply pressure should be between 60 psig and 150 psig (4.1 barg and 10.3 barg) for proper operation of the dryer. The compressed airtemperature should be within 10°F (6°C) of the ambient temperature and should not exceed120°F (49°C) for optimal operation of the membrane dryer. The ambient air temperatureshould not exceed 110°F (43°C). If the ambient temperature or compressed air temperatureexceeds recommendations, a properly sized aftercooler should be installed upstream from thedryer. Do not exceed inlet air or ambient air recommended temperatures or the perfor -mance and life of the dryer may be adversely affected and the warranty will be void. InstallationUtilitiesGeneral DescriptionThe Balston SMART Dryers (see Figure 1) provide clean, dry compressed air from an existingcompressed air supply through the use of state-of-the-art membrane technology. The dryerdelivers dry air with a dewpoint of 35°F (2°C). The compressed air supply should be between60 - 150 psig (4.1 - 10.3 barg). The dryer monitors system conditions and adjusts the sweep(regeneration flow) as system conditions warrant. The variable sweep system results in sig -nificant energy savings. Each membrane dryer is equipped with a high efficiency condensateseparator and two high efficiency coalescing prefilters to remove oil, water, and particulatecontamination to 0.01 micron.Flow Capacity(1)Model SCFM lpm SMRT5100100 2830SMRT5200200 5660SMRT5300300 8490SMRT5400400 11320SMRT5500500 14150SMRT5600600 16980Notes:1 For 35°F (2°C) dewpoint.Table 1: Compressed Air Han-dling Capacity and OperatingPressure RangePrefilter Installation Shutoff valves should be installed directly upstream and downstream from the Balston Mem-brane Dryer to facilitate routine maintenance. Use only a gate valve or other slow-opening valve upstream from the dryer. Use of a valve which is not slow-opening will pressurizethe dryer too quickly and may cause membrane rupture. Membrane failures resulting from improper valve installation will not be covered under warranty (see figure 2 or 3 for recom-mended dryer installation).The Balston Membrane Air Dryers utilize a variable "sweep" flow to carry water vapor laden air away from the membrane. The variable sweep system works by monitoring system condi-tions through the dryer and adjusting the sweep flow proportionately to the airflow throughthe dryer. The sweep flow rate is approximately 13.2% of the actual airflow through the dryer. This sweep flow results in a hiss of air from the top of the membrane modules. The total com-pressed air consumption of the dryer is the sum of the downstream demand plus the "sweep" flow. See Table 2 for the sweep flow as a function of dryer flow rate. The compressor and associated piping components must be adequately sized to supply the sweep flow and compressed air demand. (See Principal Specifications for Maximum Compressed Air Requirement for each Model.)The high efficiency condensate separator and coalescing prefilters are shipped separately from the dryer (see figure 2 or 3 for recommended prefilter installation). The drain on the prefilters will pass water and compressor oil which should be piped away to a suitable contain-ment device or drain.If the compressed air supply contains an excessive amount of condensate, a properly sized drip leg or receiver tank should be installed directly upstream from the dryer. Install an auto-matic drain on any drip leg or receiver tank used in the compressed air supply system (see figure 2 or 3 for recommended dryer installation).Model Number Max. Downstream Sweep Flow Maximum CompressedDemand Demand* Air Consumption SMRT5100 100 13.2 113.2 SMRT5200 200 26.4 226.4 SMRT5300 300 39.6 339.6 SMRT5400 400 52.8 452.8 SMRT5500 500 66.0 566.0 SMRT5600 600 79.2 679.2Table 2: Sweep Flow as a Function of Dryer Flow Rate* Sweep Flow Demand is measured at 100 PSIG and 100°F PDP per CAGI ADF 100-2001(Refrigerated Compressed Air Dryers - Methods for Testing and Rating.) Consult factory formaximum compressed air consumption at different operating conditions.To maximize membrane dryer performance, Parker recommends the following installation for a single membrane air dryer:Compressor - Piston, rotary screw, rotary vane, or liquid ring compressor.Aftercooler - Sized to bring compressed air temperature below 100°F. Air to air aftercooler should be on the same electri -cal circuit as compressor to insure operation.Air Receiver - Air line to enter the tank in the lower 1/5th of the vessel, exit at the top 1/5th . For horizontal tanks, enter the side of the tank and exit from the top.Condensate Separator - Install condensate separator in line after the receiver tank. Separator is equipped with automatic drain.Timed Solenoid Drain - Install at bottom of air receiver to remove condensate.Coalescing Filter Housings - (Included with Smart Dryer System) Install immediately upstream of dryer. Use only brass, copper, or stainless steel piping between the filters and the air dryer. Maximum distance between the filters and the air dryer should be 10 linear feet of pipe.Air Dryer - 60 to 150 psig operating pressure.Bypass Valves - (Recommended) Bypass valves should be installed after coalescing filters and before dryer.Figure 2 - Recommended SMART Membrane Dryer InstallationNotes:1 Aftercooler and condensate separator should be installed after air receiver if compressor and air receiver are built as one unit.2 Each drain line should be vented to atmosphere. Do not tie together.3 Assure that the room ambient temperature does not exceed 110°F.4 If copper piping is used, dielectric fittings must be installed on the inlet port of the air dryer.5 Compressed Air Feed Temperature to dryer must not exceed 120°F.Failure to follow these guidelines will void the warranty.Compressor - Piston, rotary screw, rotary vane, or liquid ring compressor.Aftercooler - Sized to bring compressed air temperature below 100°F. Air to air aftercooler should be on the same electri-cal circuit as compressor to insure operation.Air Receiver - Air line to enter the tank in the lower 1/5th of the vessel, exit at the top 1/5th. For horizontal tanks, enter the side of the tank and exit from the top.Timed Solenoid Drain - Install at bottom of air receiver to remove condensate with minimum line size of one inch.Drip Leg - Install drip leg from bottom of air supply header with automatic drain.Condensate Separators - Install condensate separators in line in front of coalescing filters. Separators remove excess condensate from the air line. Separators are equipped with automatic drains.Coalescing Prefilters - (Included with SMART Dryer) Install prefilter immediately upstream of dryer. Use copper, brass, or stainless pipe between filter and dryer.Membrane Air Dryer - Install non-iron piping between prefilters and membrane module cabinet.Bypass Valves - Bypass valves install after coalescing filter and before dryer.Notes:1 Each condensate drain must be functioning and vented to atmosphere. Maximum two feet incline for condensate drain lines.2 Piping must be from top of main line header to each SMART membrane air dryer.3 All SMART membrane air dryers must be piped in parallel with all feed and product air piping an equal distance from main air line headers.4 Compressed air feed temperature to dryer must not exceed 120°F.5 Assure that ambient room temperature does not exceed 110°F.Failure to follow these guidelines will void the warranty.All maintenance procedures for the SMART Dryer should be performed by suitable per -sonnel using reasonable care.Depressurize the dryer prior to performing any service.If necessary, the SMART Dryer may be wiped clean with a dry cloth on an as-needed basis. DONOT use water, aerosols, or other cleaning agents to clean the unit.The only maintenance required by the Balston SMART Series Air Dryer is the replacement of theprefilter cartridges (see Figure 4) every 12 months. The part numbers for the replacement filtersare listed in the Ordering Information table at the end of this section.The high efficiency condensate separator and coalescing prefilter housings are included withthe SMART Dryer and are installed by the customer per Figure 2 or 3. The filter cartridges arereplaced by removing the filter bowl and then unscrewing the element retainer to remove the filtercartridge. Insert a new filter cartridge and reassemble the housing in reverse order. The timerequired to change the prefilter cartridge on the Balston SMART Series Air Dryer is less than 5minutes.In the unlikely event of a membrane module failure, the membrane module can be replaced byremoving 8 socket screws on the top and bottom of the module. Slowly lift the module away fromthe dryer and disconnect the tubing from the fitting on the bottom of the membrane module. (Thetubing is disconnected by pushing on the ring then pulling on the tubing).To install a new module, install the o-ring in the grooves on the membrane module end caps andinstall the module in reverse order. First connect the tubing on the bottom then secure all8 socket cap screws. The time required to change the membrane module on the Balston SMARTSeries Air Dryer is less than 5 minutes.OperationGauges To operate the Balston Membrane Air Dryer, simply open the shutoff valves (customer installed) on the inlet and outlet air lines. Do not exceed rated flow or pressure of dryer (see Table 1).There are three gauges on the SMART Dryer. Two differential pressure (DPI) gauges aremounted on the top of the coalescing prefilter housings. A system pressure gauge is mounted onthe front panel of the SMART Dryer.MaintenanceOperationFigure 4 - Maintenance Item LocationsMembrane Air Dryers Model Number SMRT5100NA SMRT5200NA SMRT5300NA SMRT5400NA SMRT5500NA SMRT5600NA Max Flow Rate @35°F dewpoint 100 SCFM 200 SCFM 300 SCFM 400 SCFM 500 SCFM 600 SCFMDewpoint (1)35°F (2°C)Min/Max Inlet Air Temp.40°F/120°F (4°C/49°C)Ambient Temp. Range40°F/110°F (4°/43°C)Min/Max Inlet Pressure 60 psig/150 psig (4.1 barg/10 barg)Max Feed Dewpoint 120°F PDP (Pressure Dewpoint)Altitude 2000M Max Compressed Air 113 SCFM 226 SCFM 339 SCFM 452 SCFM 565 SCFM 678 SCFM Requirement (1)Max Pressure Drop 10 psi (0.7 bar)Inlet/Outlet Port Size 1-1/2"NPT(female) 2"NPT(female) 2"NPT(female) 2"NPT(female) 2-1/2"NPT(female) 3"NPT(female)Physical Dimensions (See Figure 1)Shipping Weight175 lbs(79 kg) 225 lbs(79 kg) 300 lbs(136 kg) 375 lbs(170 kg) 475 lbs(216 kg) 550 lbs(250 kg)1 Dewpoint and maximum com -pressed air required are specified for 100 psig @ 100°F PDP per CAGI ADF 100-2001 (Refrigerated com -pressed air dryers - methods for test -Principal Specifications Notes:Ordering InformationModel Number SMRT5100NA SMRT5200NA SMRT5300NA SMRT5400NA SMRT5500NA SMRT5600NAReplacement Element for Separator EK602B EK602G EK602G EK602G EK602G EK602GDrain Kit for Separator SA603D SA603D SA603D SA603D SA603D SA603DCoalescing Prefilter 2312N-1B1-DX A15/80-DX CO2-2356 CO2-2358 CO2-2360 CO2-2362Assembly - Stage 2, 3 2312N-1B1-BX A15/80-BX CO2-2357 CO2-2359 CO2-2361 CO2-2363Replacement Prefilter 200-35-DX 200-80-DX 210-800-DX 210-955-DX 300-960-DX 300-960-DX Cartridges (every 6 mos.) 200-35-BX 200-80-BX 210-800-BX 210-955-BX 300-960-BX 300-960-BXMembrane ModuleD01-0086(2ea.) D01-0086(4ea.) D01-0086(6ea.) D01-0086(8ea.) D01-0086(10ea.) D01-0086(12ea.)Automatic Drain Kit 21552 21552 21552 21552 21552 21552Drip Leg Drain 20-613 20-613 20-623 20-623 20-211 20-211►►►►►►►►ing and rating.) Contact factory for dewpoint and maximum compressed air requirement at different operating conditions.2 If compressed air is extremely contaminated, additional coalescing filters should be installed before the dryer./igfg111-800-343-4048All troubleshooting activities should be performed by suitable personnel using reasonable care.Symptom Course of Action Check drain for leaks. Replace automatic drain kit (P/N 21552 or 20-211) if necessary.Check flow demand. Match process flow requirements to dryer capacity.Check inlet filter for particulate clogging; replace if necessary.Check for leaks in dryer and downstream piping and process.Check supply line source (compressor).Check to make sure all customer installed valves are open.Check fittings and drain for leaks.Check inlet air temperature of compressor air to dryer. Inlet air should not exceed 10 degrees above ambient air temperature.Make sure inlet air is conditioned properly before the dryer. Follow guidelines on page 4 and 5. Compressor outlet should have an aftercooler with separator, air receiver with autodrain, dripleg with autodrain.Directly before the dryer check that coalescing filters are properly installed and that autodrains function properly.Check coalescing filters for excess water.Check flow rate, do not exceed dryer's maximum flow capabilities.Auto float drains are stuck in the open position. Replace autodrains, P/N 21552.Check autodrain on coalescing filters for leaks.Check inlet filters for particulate clogging; replace if necessary.Check for leaks in dryer.Make sure dryer purge is not excessive. All membranes should purge the same amount of air from top purge ports.Check flow demand. Do not exceed maximum flow capabilities of dryer.Membrane could be ruptured. See course of action for "water in outlet line" above.Replace suspect membrane.High Pressure Drop Through Dryer (low flow)No Flow Through Dryer Note: To arrange for system service, contact the Technical Services Department at 1-800-343-4048, 8AM-5PM Eastern Time or emailat:*****************************.ForlocationsoutsideNorthAmerica,pleasecallyourlocalrepresentativeoremailat ****************************.Troubleshooting Water in air outlet line Coalescing filters air constantly Large pressure drop across dryer Purge very loud from 1 or more membranes/igfg121-800-343-4048Explanation of Warning SymbolsSymbol DescriptionCaution, refer to accompanyingdocuments for explanation.Caution, risk of electric shock.1 Complete and mail or fax in your Warranty Registration Card.2Keep your product certification in a safe place.3 Call the Technical Services Department at 800-343-4048, 8AM to 5PM Eastern Time with anyquestionsoremailat:*****************************.ForlocationsoutsideNorth America,*************************************************************************.The serial number label is attached to the side of the unit, near the inlet and outlet ports. For your own records, and in case service is required, please record the following:DATE IN SERVICE SERIAL NO.Please have the serial number available when calling for assistance.Don’t Forget To:Serial Numbers WARRANTY (NORTH AMERICA ONLY)(FOR INFORMATION CONTACT YOUR LOCAL REPRESENTATIVE)Parker Hannifin guarantees to the original purchaser of this product, that if the product fails or is defectivewithin 12 months from the date of purchase, when this product is operated and maintained according to the instructions provided with the product, then Parker guarantees, at Parker’s option, to replace the product, repair the product, or refund the original price for the product. This warranty applies only to defects in material or workmanship and does not cover: ring and valve wear on compressors, routine maintenance recommended by the instructions provided with this product, or filter cartridges. Any modification of the product without written approval from Parker will result in voiding this warranty. Complete details of the war -ranty are available on request. This warranty applies to units purchased and operated in North America.CELL: SMD Parker Hannifin (UK) Ltd Gas Separation & Filtration Division EMEA Dukesway, Team Valley Trading Estate Gateshead, Tyne & Wear, NE11 0PZ United Kingdom Ph: +44 (0)191 402 /gsfeParker Hannifin Corporation Industrial Gas Filtration and Generation Division 4087 Walden Avenue Lancaster, NY 14086Tel: 716-686-6400 Fax: /igfg Copyright© Parker Hannifin Corporation 2004, 2018Printed in U.S.A. Bulletin TI-5100J。

Notes: All height, width and depth dimensions are shown in inches. BSH reserves the absolute and unrestricted right to change product materials and specifications, at any time, without notice. Consult the product’s installation instructions for final dimensional data and other details prior to making cutout.
Minimum water pressure 14 lb/sin
Length outlet hose
78 3/4"
Dimensions & Weight
ห้องสมุดไป่ตู้
Overall appliance dimensions (HxWxD)
33 7/8" x 23 9/16" x 23 3/4"
Required cutout size (HxWxD)
Enhance your cleaning experience with Wi-Fi enabled Home Connect®. Access additional wash cycles and options or choose the right one for your needs using Smart Cycle.
33 7/8" x 24" x 24"
Adjustable feet
Yes
Net weight