尿微量白蛋白(mALB)检测试剂盒(化学发光—免疫分析法)产品技术要求深圳安群生物

尿微量白蛋白检测试剂盒（胶体金免疫层析法）适用范围：本产品适用于对人尿液中白蛋白进行体外定性检测。

1. 产品型号/规格及其划分说明1.1 产品型号产品型号及分类如下表1：表1 产品型号及分类U系列（卡型）G系列（条型）宽度(mm)U2 G2 2.5U3 G3 3.3U4 G4 4.0U5 G5 5.0注：产品相同系列不同型号间除试剂条宽度外，其余完全一致。

U系列是在G系列试剂条的基础上加卡壳，其余完全一致。

1.2包装规格卡型：25人份/盒、1人份/袋；条型：100人份/盒；50人份/盒；25人份/盒；1人份/袋。

1.3主要组成成分（1）检测试剂卡/条由样品垫、金结合物垫（胶体金标记的抗人白蛋白单克隆抗体复合物垫片）、硝酸纤维素膜（T线包被有人白蛋白，C线包被有羊抗鼠IgG 抗体）、吸水纸、PVC胶板构成。

（2）干燥剂。

2. 性能指标2.1 物理性状2.1.1 外观a)试剂盒的外观应平整、边缘无毛刺；包装完整、标签清晰可辨；b)测试块与基底片固定应紧密、不能有缺损或脱落；c)测试块外观整齐、色泽均匀、不能有色斑或污渍。

2.1.2 膜条宽度试纸条宽度应U2、G2不小于2.5mm；U3、G3不小于3.3mm；U4、G4不小于4.0mm；U5、G5不小于5.0mm。

2.1.3 液体移行速度液体移行速度应不低于10mm/min。

2.2 临界值及重复性临界值为17.5μg/ml；用浓度为20μg/ml白蛋白质控液重复检测次数≥20，测定结果的阳性率应≥95%，且显色一致；用浓度为15μg/ml白蛋白质控液重复检测次数≥20，结果的阴性率应≥95%，且显色一致。

2.3 准确性用浓度为20μg/ml的尿微量白蛋白阳性质控品重复检测3次，结果应均为阳性。

2.4 批间差取三个批次的试剂盒，用浓度为20μg/ml白蛋白质控液重复检测次数≥20，结果的阳性率应≥95%，且显色一致；用浓度为15μg/ml白蛋白质控液重复检测次数≥20，结果的阴性率应≥95%，且显色一致。

尿微量白蛋白（MAU）测定试剂盒（胶体金免疫层析法）适用范围：于体外定量测定人尿液中的尿微量白蛋白(MAU)含量。

1.1包装规格20人份/盒1.2 主要组成成分本试剂盒由MAU检测卡、干燥剂和滴管组成。

MAU检测卡由试纸条外壳与试纸条构成。

试纸条由样品垫、胶体金垫（喷有由胶体金标记的MAU单克隆抗体）、层析膜（T线包被有MAU单克隆抗体，C线包被有羊抗鼠IgG抗体）、吸水纸、衬垫构成。

检测卡为20人份/盒，干燥剂为1个/袋，滴管为20个/盒。

2.1 物理性状2.1.1 外观试剂盒各组分齐全、完整；包装袋应密封性好无破损；标签清晰；材料附着牢固，条宽应适应于卡壳且装配紧密。

2.1.2 膜条宽度膜条宽度应不低于4.0mm。

2.1.3 液体移行速度液体移行速度应不低于10mm/min。

2.2 空白检测限应小于5.0mg/L。

2.3 重复性用10mg/L尿微量白蛋白（MAU）参考品和100mg/L尿微量白蛋白（MAU）参考品各重复检测10次，其变异系数（CV）应不大于15%。

2.4 准确度将200.0mg/L尿微量白蛋白(MAU)参考品加入到尿微量白蛋白（MAU）含量5.0mg/L 正常人尿液参考品中，按照体积比1:9混合，对混合后样本进行检测，回收率应在85%～115%范围内。

2.5 线性线性范围为[5.0,200]mg/L，试剂盒的相关系数r应≥0.99。

2.6 批间差用3个批号试剂盒分别对10.0mg/L尿微量白蛋白（MAU）参考品和100.0mg/L 尿微量白蛋白（MAU）参考品各重复检测10次，则3个批号试剂盒之间的批间相对偏差（R）应不大于15%。

2.7 稳定性效期稳定性：2～30℃条件下放置有效期12个月后一个月内，检测物理性状、空白检测限、重复性、准确度、线性应符合2.1～2.6项的要求。

尿微量白蛋白质控品
适用范围：本产品与本公司相应试剂盒配套使用，用于临床检验实验室尿微量白蛋白项目的质量控制。

1.1规格
液体型
1mL×1（水平1）；3mL×1（水平1）；
1mL×1（水平2）；3mL×1（水平2）；
1mL×2（水平1，水平2）；1mL×6（水平1，水平2）；
3mL×2（水平1，水平2）；3mL×6（水平1，水平2）。

1.2规格划分说明
根据净含量划分规格。

1.3主要组成成分
本产品以PBS缓冲液为基质,并添加含有人源性的白蛋白成分。

主要成分为白蛋白，定值范围：水平1: 20～50mg/L，水平2: 120～200mg/L（每批定值）。

2.1 外观
本质控品为无色或浅黄色透明溶液，无混浊，无未溶解物，外包装完整无破损。

2.2 质控品定值有效性
测定结果应在质控范围内。

2.3 重复性
变异系数（CV）应≤10%。

2.4稳定性
原包装质控品在2℃～8℃条件下避光贮存，有效期为12个月。

在质控品有效期满后3个月内，质控品性能应符合2.1、2.2、2.3要求。

尿微量白蛋白（ALB）测定试剂盒（酶联免疫吸附法）适用范围：本试剂盒用于体外定量测定人尿液样本中微量白蛋白(ALB)浓度。

1.1 包装规格48人份、96人份1.2 主要组成成分质控品质控范围批特异，详见标签。

2.1 外观2.1.1 试剂盒各组分应齐全、完整，液体无渗漏。

2.1.2 标识应清晰，易识别。

2.2 空白检出限空白检出限浓度应不高于2.0ng/ml。

2.3 线性在[0.4，51.2]mg/L范围内线性相关系数r≥0.9900。

2.4 重复性分别用高、低浓度的样品各重复检测10次（样品浓度范围20mg/L±4.0mg/L和12.8mg/L±3.0 mg/L），其变异系数（CV）应不大于10%。

2.5 准确度用中国食品药品检定研究院的人血清白蛋白标准品（270009）对试剂盒进行测试，相对偏差（B）应不超过±20%。

2.6 分析特异性按表1所示交叉反应物规定浓度进行测定，检测结果的浓度值不得超过4.0mg/L。

表1：交叉反应物及浓度列表2.7 溯源性根据GB/T21415-2008《体外诊断医疗器械生物样品中量的测量校准品和控制物质赋值的计量学溯源性》及有关规定提供校准品的来源、赋值过程及测量不确定度等内容。

校准品溯源至企业工作校准品，并与已上市产品比对赋值。

2.8 质控品赋值有效性本试剂盒质控品的测定结果应在质控范围内。

2.9 批间差用3个批号试剂盒检测同一份样品（样品浓度范围20mg/L±4.0mg/L），则三个批号试剂盒之间的批间变异系数CV(%)应不超于15%。

2.10 稳定性将试剂盒各组分置2℃～8℃放置，有效期为12个月，效期后两个月内，检定结果应符合2.1、2.2、2.3、2.4、2.5、2.6的规定。

人尿微量白蛋白(m-Alb)检测试剂盒(透射微板法)简介：Viberti 等人发现尿中白蛋白排泄的增加率，可以提示胰岛素依赖性糖尿病肾病发作，但此时尿中总蛋白排泄正常，尿常规蛋白定性实验为阴性，而尿白蛋白排泄增加，称之为微量白蛋白(microablumin ，m-Alb)尿。

Leagene 人尿微量白蛋白(m-Alb)检测试剂盒(透射微板法)其检测原理是尿液中的白蛋白与抗白蛋白特异抗体在液相中反应生成m-Alb 抗原抗体复合物，使反应液呈一定浊度。

本试剂盒专门用于人尿液中的微量白蛋白含量测定。

本试剂盒仅用于科研领域，不宜用于临床诊断或其他用途。

组成：操作步骤(仅供参考)：1、 准备试剂：临用前，各种试剂均应平衡至室温。

2、 绘制标准曲线：取白蛋白标准(198mg/L)，依次稀释后供标准曲线用，其浓度分别为198mg/L 、99.0mg/L 、49.5mg/L 、19.8mg/L 、9.9mg/L 。

3、 m-Alb 测定操作：酶标仪检测，按下表依次加入试剂：4、 充分混匀, 盖上塑料膜，37℃孵育。

5、 再次混匀，酶标仪测定波长处的吸光度。

以空白管调零，读取标准管和各待测管的最终吸光度为A 2。

编号 名称TC0687100T Storage试剂(A): m-Alb buffer 10ml RT 试剂(B): 白蛋白标准(198mg/L) 0.1ml -20℃ 试剂(C): m-Alb 抗体工作液 0.15ml -20℃ 试剂(D): m-Alb 生理盐水 10mlRT 使用说明书1份标准管 待测管 m-Alb buffer(μl) 200 200 白蛋白标准(μl) 20 待测样本(μl)20混匀，m-Alb 生理盐水调零，读取起始吸光度A 1，然后加入： m-Alb 抗体工作液(μl)20206、绘制标准曲线：以上述5种浓度的标准液，分别制作5个标准管，同上操作，测定吸光度。

A标准=A2标准-A1标准A标准和对应的白蛋白浓度在半对数纸上制图，绘制标准曲线。

Human microalbunminuria(MAU/ALB) ELISA kit Catalog Number. CSB-E08970hFor the quantitative determination of human microalbunminuria(MAU/ALB) concentrations in serum, plasma, urine.This package insert must be read in its entirety before using this product.If You Have ProblemsTechnical Service Contact informationPhone: 86-27-87582341Fax: 86-27-87196150Email:****************Web: In order to obtain higher efficiency service, please ready to supply the lot numberof the kit to us (found on the outside of the box).1PRINCIPLE OF THE ASSAYThis assay employs the competitive inhibition enzyme immunoassay technique. Antibody specific for MAU has been pre-coated onto a microplate. Standards and samples are pipetted into the wells with biotin-conjugated MAU. A competitive inhibition reaction is launched between MAU (Standards or samples) and biotin-conjugated MAU with the pre-coated MAU antibody. After washing, avidin conjugated Horseradish Peroxidase (HRP) is added to the wells. Following a wash to remove any unbound reagent, a substrate solution is added to the wells and color develops in opposite to the amount of MAU bound in the initial step. The color development is stopped and the intensity of the color is measured.DETECTION RANGE0.078 µg/ml-5 µg/ml.SENSITIVITYThe minimum detectable dose of human MAU is typically less than 0.019 µg/ml. The sensitivity of this assay, or Lower Limit of Detection (LLD) was defined as the lowest human MAU concentration that could be differentiated from zero.SPECIFICITYThis assay has high sensitivity and excellent specificity for detection of human MAU. No significant cross-reactivity or interference between human MAU and analogues was observed.Note: Limited by current skills and knowledge, it is impossible for us to complete the cross-reactivity detection between human MAU and all the analogues, therefore, cross reaction may still exist.2PRECISIONIntra-assay Precision (Precision within an assay): CV%<8%Three samples of known concentration were tested twenty times on one plate to assess.Inter-assay Precision (Precision between assays):CV%<10%Three samples of known concentration were tested in twenty assays to assess.LIMITATIONS OF THE PROCEDUREFOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.The kit should not be used beyond the expiration date on the kit label.Do not mix or substitute reagents with those from other lots or sources.If samples generate values higher than the highest standard, dilute the samples with Sample Diluent and repeat the assay.Any variation in Sample Diluent, operator, pipetting technique, washing technique, incubation time or temperature, and kit age can cause variation in binding.This assay is designed to eliminate interference by soluble receptors, binding proteins, and other factors present in biological samples. Until all factors have been tested in the Immunoassay, the possibility of interference cannot be excluded.3MATERIALS PROVIDEDReagents QuantityAssay plate (12 x 8 coated Microwells) 1(96 wells) Standard (Freeze dried) 2Biotin-conjugate (100 x concentrate) 1 x 60 µlHRP-avidin (100 x concentrate) 1 x 120 µlBiotin-conjugate Diluent 1 x 10 mlHRP-avidin Diluent 1 x 20 ml Sample Diluent 2 x 20 mlWash Buffer (25 x concentrate) 1 x 20 mlTMB Substrate 1 x 10 mlStop Solution 1 x 10 ml Adhesive Strip (For 96 wells) 4Instruction manual 1STORAGEUnopenedkitStore at 2 - 8°C. Do not use the kit beyond the expiration date.Opened kitCoated assayplateMay be stored for up to 1 month at 2 - 8°C.Try to keep it in a sealed aluminum foil bag,and avoid the damp.Standard May be stored for up to 1 month at 2 - 8° C.If don’t make recent use, better keep it storeat -20°C.HRP-avidinBiotin-conjugateBiotin-conjugateDiluentMay be stored for up to 1 month at 2 - 8°C. HRP-avidinDiluentSample DiluentWash BufferTMB SubstrateStop Solution*Provided this is within the expiration date of the kit.4OTHER SUPPLIES REQUIREDMicroplate reader capable of measuring absorbance at 450 nm, with the correction wavelength set at 540 nm or 570 nm.An incubator which can provide stable incubation conditions up to 37°C±0.5°C.Squirt bottle, manifold dispenser, or automated microplate washer.Absorbent paper for blotting the microtiter plate.100ml and 500ml graduated cylinders.Deionized or distilled water.Pipettes and pipette tips.Test tubes for dilution.PRECAUTIONSThe Stop Solution provided with this kit is an acid solution. Wear eye, hand, face, and clothing protection when using this material.5SAMPLE COLLECTION AND STORAGESerum Use a serum separator tube (SST) and allow samples to clot for30 minutes before centrifugation for 15 minutes at 1000 x g, 2 - 8°C.Remove serum and assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw cycles. Centrifuge the sample again after thawing before the assay.Plasma Collect plasma using EDTA, or heparin as an anticoagulant.Centrifuge for 15 minutes at 1000 x g, 2 - 8°C within 30 minutes of collection. Assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw cycles. Centrifuge the sample again after thawing before the assay.Urine Use a sterile container to collect urine samples. Remove any particulates by centrifugation for 15 minutes at 1000xg, 2 - 8°C and assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw cycles. Centrifuge again before assaying to remove any additional precipitates that may appear after storage.SAMPLE PREPARATIONRecommend to dilute the serum or plasma samples 50000-fold before test.The suggested 50000-fold dilution can be achieved by adding 2µl sample to 398µl of normal saline. Complete the 50000-fold dilution by adding 2µl of this solution to 498µl of Sample Diluent. The recommended dilution factor is for reference only. The optimal dilution factor should be determined by users according to their particular experiments.Recommend to dilute the urine samples with Sample Diluent(1:40) before test. The suggested 40-fold dilution can be achieved by adding 6µl sample to 234µl of Sample Diluent. The recommended dilution factor is for reference only. The optimal dilution factor should be determined by users according to their particular experiments6Note:1. CUSABIO is only responsible for the kit itself, but not for the samplesconsumed during the assay. The user should calculate the possible amount of the samples used in the whole test. Please reserve sufficient samples in advance.2. Samples to be used within 5 days may be stored at 2-8°C, otherwisesamples must be stored at -20°C (≤1month) or -80°C (≤2month) to avoid loss of bioactivity and contamination.3. Grossly hemolyzed samples are not suitable for use in this assay.4. If the samples are not indicated in the manual, a preliminary experiment todetermine the validity of the kit is necessary.5. Please predict the concentration before assaying. If values for these arenot within the range of the standard curve, users must determine the optimal sample dilutions for their particular experiments.6. Tissue or cell extraction samples prepared by chemical lysis buffer maycause unexpected ELISA results due to the impacts of certain chemicals.7. Owing to the possibility of mismatching between antigen from otherresource and antibody used in our kits (e.g., antibody targets conformational epitope rather than linear epitope), some native or recombinant proteins from other manufacturers may not be recognized by our products.8. Influenced by the factors including cell viability, cell number and alsosampling time, samples from cell culture supernatant may not be detected by the kit.9. Fresh samples without long time storage are recommended for the test.Otherwise, protein degradation and denaturalization may occur in those samples and finally lead to wrong results.7REAGENT PREPARATIONNote:Kindly use graduated containers to prepare the reagent. Please don't prepare the reagent directly in the Diluent vials provided in the kit. Bring all reagents to room temperature (18-25°C) before use for 30min.Prepare fresh standard for each assay. Use within 4 hours and discard after use.Making serial dilution in the wells directly is not permitted.Please carefully reconstitute Standards according to the instruction, and avoid foaming and mix gently until the crystals have completely dissolved.To minimize imprecision caused by pipetting, use small volumes and ensure that pipettors are calibrated. It is recommended to suck more than 10µl for once pipetting.Distilled water is recommended to be used to make the preparation for reagents. Contaminated water or container for reagent preparation will influence the detection result.1. Biotin-conjugate (1x) - Centrifuge the vial before opening.Biotin-conjugate requires a 100-fold dilution. A suggested 100-fold dilution is 10 µl of Biotin-conjugate + 990 µl of Biotin-conjugate Diluent.2. HRP-avidin (1x) - Centrifuge the vial before opening.HRP-avidin requires a 100-fold dilution. A suggested 100-fold dilution is 10 µl of HRP-avidin + 990 µl of HRP-avidin Diluent.3. Wash Buffer(1x)- If crystals have formed in the concentrate, warm up toroom temperature and mix gently until the crystals have completely dissolved. Dilute 20 ml of Wash Buffer Concentrate (25 x) into deionized or distilled water to prepare 500 ml of Wash Buffer (1 x).894.StandardCentrifuge the standard vial at 6000-10000rpm for 30s.Reconstitute the Standard with 1.0 ml of Sample Diluent . Do not substitute other diluents. This reconstitution produces a stock solution of 5 µg/ml. Mix the standard to ensure complete reconstitution and allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making dilutions.Pipette 150 µl of Sample Diluent into each tube (S0-S6). Use the stock solution to produce a 2-fold dilution series (below). Mix each tube thoroughly before the next transfer. The undiluted Standard serves as the high standard (5 µg/ml). Sample Diluent serves as the zero standard (0 µg/ml).Tube S7 S6 S5S4 S3 S2 S1 S0 µg/ml52.51.250.6250.3120.1560.078ASSAY PROCEDUREBring all reagents and samples to room temperature before use. Centrifuge the sample again after thawing before the assay.It is recommended that all samples and standards be assayed in duplicate.1. Prepare all reagents, working standards, and samples as directed in theprevious sections.2. Refer to the Assay Layout Sheet to determine the number of wells to beused and put any remaining wells and the desiccant back into the pouch and seal the ziploc, store unused wells at 4°C.3. Set a Blank well without any solution.4. Add 50µl of standard and sample per well.5. Add 50µl of Biotin-conjugate(1x) to each well(not to Blank well). Coverwith a new adhesive strip. Incubate for 60 minutes at 37°C.(Biotin-conjugate(1x) may appear cloudy. Warm up to room temperature and mix gently until solution appears uniform.)6. Aspirate each well and wash, repeating the process two times for a total ofthree washes. Wash by filling each well with Wash Buffer (200µl) using a squirt bottle, multi-channel pipette, manifold dispenser, or autowasher, and let it stand for 2 minutes, complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.7. Add 100µl of HRP-avidin(1x) to each well(not to Blank well). Cover themicrotiter plate with a new adhesive strip. Incubate for 60 minutes at 37°C.8. Repeat the aspiration/wash process for five times as in step 6.9. Add 90µl of TMB Substrate to each well. Incubate for 20 minutes at 37°C.Protect from light.10. Add 50µl of Stop Solution to each well, gently tap the plate to ensurethorough mixing.1011. Determine the optical density of each well within 5 minutes, using amicroplate reader set to 450 nm. If wavelength correction is available, set to 540 nm or 570 nm. Subtract readings at 540 nm or 570 nm from the readings at 450 nm. This subtraction will correct for optical imperfections in the plate. Readings made directly at 450 nm without correction may be higher and less accurate.*Samples may require dilution. Please refer to Sample Preparation section. Note:1. The final experimental results will be closely related to validity of theproducts, operation skills of the end users and the experimental environments.2. Samples or reagents addition: Please use the freshly prepared Standard.Please carefully add samples to wells and mix gently to avoid foaming. Do not touch the well wall as possible. For each step in the procedure, total dispensing time for addition of reagents or samples to the assay plate should not exceed 10 minutes. This will ensure equal elapsed time for each pipetting step, without interruption. Duplication of all standards and specimens, although not required, is recommended. To avoid cross-contamination, change pipette tips between additions of each standard level, between sample additions, and between reagent additions.Also, use separate reservoirs for each reagent.3. Incubation: To ensure accurate results, proper adhesion of plate sealersduring incubation steps is necessary. Do not allow wells to sit uncovered for extended periods between incubation steps. Once reagents have been added to the well strips, DO NOT let the strips DRY at any time during the assay. Incubation time and temperature must be observed.4. Washing: The wash procedure is critical. Complete removal of liquid ateach step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting and remove any drop of water and fingerprint on the bottom of the plate. Insufficient washing will result in poor precision and falsely elevated absorbance reading. When using an automated plate washer, adding a 30 second soak period following the addition of wash buffer, and/or rotating the plate 180 degrees between wash steps may improve assay precision.115. Controlling of reaction time: Observe the change of color after adding TMBSubstrate (e.g. observation once every 10 minutes), TMB Substrate should change from colorless or light blue to gradations of blue. If the color is too deep, add Stop Solution in advance to avoid excessively strong reaction which will result in inaccurate absorbance reading.6. TMB Substrate is easily contaminated. TMB Substrate should remaincolorless or light blue until added to the plate. Please protect it from light.7. Stop Solution should be added to the plate in the same order as the TMBSubstrate. The color developed in the wells will turn from blue to yellow upon addition of the Stop Solution. Wells that are green in color indicate that the Stop Solution has not mixed thoroughly with the TMB Substrate.1213ASSAY PROCEDURE SUMMARY*Samples may require dilution. Please refer to Sample Preparation section.CALCULATION OF RESULTSUsing the professional soft "Curve Expert" to make a standard curve is recommended, which can be downloaded from our web.Average the duplicate readings for each standard and sample and subtract the average optical density of Blank.Create a standard curve by reducing the data using computer software capable of generating a four parameter logistic (4-PL) curve-fit. As an alternative, construct a standard curve by plotting the mean absorbance for each standard on the x-axis against the concentration on the y-axis and draw a best fit curve through the points on the graph. The data may be linearized by plotting the log of the MAU concentrations versus the log of the O.D. and the best fit line can be determined by regression analysis. This procedure will produce an adequate but less precise fit of the data.If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor.14人尿微量白蛋白(MAU/ALB)酶联免疫试剂盒使用说明书【产品编号】CSB-E08970h【预期应用】ELISA法定量测定人血清、血浆、尿液中MAU含量。

尿微量白蛋白（MALB）测定试剂盒（胶乳免疫比浊法）适用范围：用于体外定量测定人尿液中微量白蛋白（MALB）的含量。

1.1 包装规格试剂1：1×80mL，试剂2：1×20mL；试剂1：50×240μL，试剂2：1×3mL；试剂1：30×240μL，试剂2：1×1.8mL。

1.2 主要组成成分2.1 外观和性状试剂1为清澈透明的液体，无沉淀、悬浮物和絮状物。

试剂2为乳白色悬浮液，无沉淀。

2.2 净含量每瓶试剂的净含量应不少于标示值。

2.3 试剂空白吸光度用纯化水加入试剂作为样品测试时，试剂空白吸光度A应≤1.5。

2.4 分析灵敏度测含156mg/L微量白蛋白尿液样本时，吸光度差值（ΔA）应≥0.04。

2.5 线性试剂盒在[10,200]mg/L的线性范围内分析性能应符合如下要求：2.5.1 线性相关系数（r）≥0.990；2.5.2 相对偏差：浓度在（35，200]mg/L范围内，相对偏差不超过10%；2.5.3 绝对偏差：浓度在[10，35]mg/L范围内，绝对偏差不超过3.5mg/L。

2.6 测量精密度2.6.1 重复性用高低两个浓度样本重复测试，所得结果变异系数（CV）应≤10%。

2.6.2 批间差试剂盒的批间相对极差（R）应≤15.0％。

2.7 准确度在样品中加入一定量的纯品，计算回收率，应在85%～115%范围内。

2.8 稳定性2℃～8℃避光贮存，有效期为12个月，取过有效期后一个月内的试剂盒进行检测，试剂盒应仍能符合2.1、2.3、2.4、2.5、2.6.1、2.7要求。

微量白蛋白测定试剂盒（免疫透射比浊法）2.性能指标2.1外观a)试剂盒各组分应齐全、完整；液体无渗漏；包装标签应清晰、准确、牢固。

b)试剂瓶内的试剂应为清澈透明液体，无沉淀、无悬浮物、无絮状物。

2.2装量试剂装量应符合表 2 的要求。

表 2 装量要求试剂组分数量（瓶）每瓶装量R1 3 ≥ 60 mLR2 1 ≥ 60 mLR1 3 ≥ 60 mLR2 1 ≥ 60 mL 校准品 1 1 ≥ 10 mL校准品 6 1 ≥ 2 mLR1 1 ≥ 60 mLR2 1 ≥ 20 mLR1 1 ≥ 60 mLR2 1 ≥ 20 mL 校准品 1 1 ≥ 10 mL校准品 6 1 ≥ 2 mLR1 2 ≥ 30 mL R2 2 ≥ 10 mL R1 2 ≥ 30 mL R2 2 ≥ 10 mL试剂组分数量（瓶）每瓶装量校准品1 1 ≥ 10 mL校准品6 1 ≥ 2 mL2.3空白限不大于0.6 mg/L。

2.4分析灵敏度试剂盒测试30 mg/L 的被测物时，其吸光度差值≥0.040 Abs。

2.5线性区间试剂盒线性在[7，1000] mg/L 区间内，应符合如下要求：a)线性相关系数（r）≥0.990；b) [7，100] mg/L 区间内，线性绝对偏差在±10 mg/L 范围内；(100，1000] mg/L 区间内，线性相对偏差在±10%范围内。

2.6精密度2.6.1重复性试剂盒测试浓度在（25±5）mg/L 和（200±40）mg/L 范围内的样本时，变异系数（CV）≤5.0%。

2.6.2批间差试剂盒测试浓度在（25±5）mg/L 和（200±40）mg/L 范围内的样本时，相对极差（R）≤10.0%。

2.7准确度测试有证参考物质或可溯源至有证参考物质的企业校准品，测定值与理论值的相对偏差应在±10.0%范围内。

2.8校准品外观a)校准品的外观应整洁，标识应清晰、准确、牢固；b)瓶内液体清澈透明，无沉淀、无悬浮物、无絮状物。

水平1：1mL×1；1mL×10；5mL×1；5mL×10；
水平2：1mL×1；1mL×10；5mL×1；5mL×10；
水平1：1mL×1，水平2：1mL×1；
水平1：5mL×1，水平2：5mL×1。

1.2主要组成成分
2水平，牛血清基质冻干质控品
注：质控品质控范围批特异，详见瓶签。

2.1性状
质控品为白色至淡黄色冻干粉末。

2.2可接受区间
质控品测定值应在靶值范围内。

2.3瓶间均匀性
赋值结果的瓶间均匀性变异系数（CV）≤5%。

2.4稳定性
2.4.1效期稳定性
质控品原包装在2℃～8℃避光保存，有效期为18个月，在稳定期内赋值结果的变化趋势不显著。

2.4.2复溶稳定性
质控品复溶后，在2℃～8℃下避光密封保存，可保存24小时，在-20℃下避光密封保存，避免反复冻融，可保存30天，在稳定期内赋值结果的变化趋势不显著。