亚安产品手册

25.10.2016 ­ 10:34:26hDatasheet ­ AZM 161 B ST1­AS A AZM 161 B ST1­AS AAS interface safety at work / Safety switchgear / Solenoid interlock / AZM 161ASPreferred typ(Minor differences between the printed image and the original product may exist!)• Solenoid interlock• Thermoplastic enclosure • High holding force 2000 N • 130 mm x 90 mm x 30 mm• Interlock with protection against incorrect locking.• Double­insulated • Long life• Integrated AS­Interface• Solenoid supply aus AS interface • Actuator monitored • Manual releaseOrdering detailsProduct type description AZM 161 B ST1­AS A Article number 101209091EAN code 4030661396446eCl@ss 27­27­26­03ApprovalApprovalAS­iTÜV USA/CANClassificationStandards EN ISO 13849­1, IEC 61508PLup c Control category 1PFH 1.14 x 10­6 / h­ notice up to max. 100.000 switching cycles/year SIL up 1Mission time20 Y earsIf a fault exclusion for hazardous damage of the 1­channel mechanics is authorized and an adequate protection against tampering is ensured, suitable for use up to:Standards EN ISO 13849­1, IEC 61508PLup d Control category 3PFH value 1.01 x 10­7 / h­ notice up to max. 100.000 switching cycles/year SIL up 2Mission time20 Y earsGlobal PropertiesProduct name AZM 161 ASStandards EN 50295, EN 60947­5­1, IEC 61508, EN ISO 13849­1 Compliance with the Directives (Y/N) Y esNumber of actuating directions3 pieceActive principle electromechanicalDuty cycle Magnet 100 %Materials­ Material of the housings Plastic, glass­fibre reinforced thermoplastic, self­extinguishingHousing coating NoneWeight450 gGuard locking monitored (Y/N)NoActuator monitored (Y/N)Y esResponse time< 100 msMechanical dataActuating play in direction of actuation 5.5 mmDesign of electrical connection connector plug M12, 4­poleconnector rightMechanical life> 1.000.000 operationsrestistance to shock30 g / 11 msResistance to vibration10 Hz ... 150 Hz, Amplitude 0,35 mmEmergency unlocking device (Y/N)NoManual release (Y/N)Y esEmergency release (Y/N)NoLatching force5 NClamping force F2000 NMax. Actuating speed2 m/sActuating frequency max. 1000 / hAmbient conditionsAmbient temperature­ Min. environmental temperature−25 °C­ Max. environmental temperature+60 °CStorage and transport temperature­ Min. Storage and transport temperature−25 °C­ Max. Storage and transport temperature+85 °CRelative humidity30 % ... 95 %­ non­condensingProtection class IP67 to IEC/EN 60529Protection rating IIAir clearances and creepage distances To IEC/EN 60664­1­ Rated impulse withstand voltage U imp0,8 kV­ Rated insulation voltage U i32 VDC­ Overvoltage category III­ Degree of pollution3Electrical dataPower to unlock NoPower to lock Y esElectrical data ­ AS interfaceAS­i Supply voltage26.5 ... 31.6 VDC, Protection against polarity reversalAS­i operating current≤ 250 mAAS­i Device insulation internally short­circuit proofAS­i Specification­ version V 2.1­ Profile S­7.B.F.E­ IO­Code0x7­ ID­Code0xB­ ID­Code10xF­ ID­Code20xEAS­i Inputs­ Channel 1Data bits DI 0/DI 1= dynamic code transmission­ Channel 2Data bits DI 2/DI 3= dynamic code transmissionAS­i Outputs­ DO 0Solenoid control­ DO 1not used­ DO 2not used­ DO 3not usedAS­i Parameter bits­ P0Actuator detected­ P1Solenoid interlock locked­ P2magnet voltage in tolerance range­ P3error message ­ locking/unlocking of the solenoid interlockblockedAS­i input module address0­ Default on address 0, programmable via the AS­Interface Master or Hand­held programming deviceLED switching conditions displayLED switching conditions display (Y/N)Y esAS­i LED switching conditions display(1) yellow LED Channel 2 / AS­i SaW Bit 2,3(2) green/red LED (AS­i duo LED)Supply voltage / Communication error / slave address = 0or periphery error(3) yellow LED Channel 1 / AS­i SaW Bit 0,1ATEXExplosion protection categories for gases NoneExplosion protected category for dusts NoneMiscellaneous dataApplicationssliding safety guard,removable guard,hinged safety guardDimensionsDimensions of the sensor­ Width of sensor130 mm­ Height of sensor90 mm­ Length of sensor30 mmPin assignment1AS­i +2Aux − (P)3AS­i −4Aux + (P)noticeInterlocks with power to lock principle may only be used in special cases after a thorough evaluation of the accident risk, since the guarding device can immediately be opened on failure of the electrical power supply or when the main switch is opened.Manual release• For maintenance, installation, etc.• For manual release using M5 triangular key, available as accessoryIncluded in deliveryActuators must be ordered separately.Ordering codeAZM 161 (1) (2)­AS (3)(4)(5)(6)(1)Z Guard lockingmonitoredB Actuator monitoredBZ(2)ST1Connector bottomST2Connector right(3)without Latching force 5 NR Latching force 30 N(4)without Power to unlockA Power to lock(5)without Solenoid supply ausAS interfaceP Solenoid supply aus24 VDC (Aux)(6)without Manual releaseN Emergency releaseT Emergency exitDocumentsOperating instructions and Declaration of conformity (en) 569 kB, 12.03.2010Code: mrl_azm161as_enOperating instructions and Declaration of conformity (it) 493 kB, 15.03.2010Code: mrl_azm161as_itOperating instructions and Declaration of conformity (es) 495 kB, 16.03.2010Code: mrl_azm161as_esOperating instructions and Declaration of conformity (pl) 319 kB, 11.02.2015Code: mrl_azm161as_plOperating instructions and Declaration of conformity (de) 572 kB, 12.03.2010Code: mrl_azm161as_deOperating instructions and Declaration of conformity (fr) 485 kB, 15.03.2010Code: mrl_azm161as_frOperating instructions and Declaration of conformity (jp) 712 kB, 14.11.2011Code: mrl_azm161as_jpOperating instructions and Declaration of conformity (nl) 478 kB, 15.03.2010Code: mrl_azm161as_nlBG­test certificate (de, en) 286 kB, 01.06.2010Code: z_161p01ImagesDimensional drawing (basic component)Contact arrangementOperating principleSystem componentsActuator101145117 ­ AZM 161­B1101144416 ­ AZM 161­B1E101171859 ­ AZM 161­B1ES101175431 ­ AZM 161­B1F101171125 ­ AZM 161­B1S101173089 ­ AZM 161­B1­2053 WITH BALL LATCH101164100 ­ AZM 161­B1­1747 WITH MAGNETIC LATCH101178199 ­ AZM 161­B1­2024101176642 ­ AZM 161­B1­2177 WITH CENTERING GUIDE101174113 ­ AZM 161­B6­2177 WITH CENTERINGGUIDE• For very smal actuating radii101170375 ­ AZM 161­B6S101144420 ­ AZM 161­B6• For very smal actuating radiiDoor­handle systemAZM 161­STS30• Latching handle• Suitable for all types of guard• einsetzbar in Verbindung mit EX­AZM 161suitable in combination with #01#Accessories101100887 ­ TRIANGULAR KEY TK­M5• For manual release using M5 triangular key, available asaccessory• For maintenance, installation, etc.K.A. Schmersal GmbH & Co. KG, Möddinghofe 30, D­42279 WuppertalThe data and values have been checked throroughly. Technical modifications and errors excepted.Generiert am 25.10.2016 ­ 10:34:26h Kasbase 3.2.5.F.64I。

亚安产品手册亚安产品型号定义（适用范围：镜头、控制主机键盘、云台、防护罩、球型云台、球型云台/球型摄像机、摄像机、监视器、数字录像存储设备、音频视频解码器）模块化综合传输光端机光端机，就是光信号传输的终端设备。

由于目前技术的提高，光纤价格的降低使它在各个领域得到很好的应用，因此各个光端机的厂家就好比是雨后春笋般发展起来。

但是这里的厂家大部分技术并不是完全成熟，开发新技术需要耗资和人力、物力等，这就产生厂家多是中小企业，各品牌也先后岀现。

但是质量上还是差不多的，国外的光端机好但是价格昂贵，因此，国内厂家把生产光端机转型岀路了，用来满足国内的需要。

园区视频监控方案展开光端机简介概念工作原理光端机的常用术语光端机分类PDH光端机SDH光端机SPDH光端机通常所说的光端机概述1、模拟光端机2、数字光端机光端机从模拟走向数字光端机的传输距离光端机接口类型光端机品牌常见故障及解决方法一、没有视频信号二、画面出现干扰雪花常见故障解决之道视频光端机的选型视频光端机网管介绍主要特点如下光端机的特性：传输系统原理园区视频监控方案展开10MHz，音频带宽为40Hz〜20KHZ，体现了较强的动态范围宽度。

信噪比信噪比(SNR:Signal To Noise Ratio )是指光端机音源产生最大不失真声音信号强度与同时发岀的噪音强度之间的比率，通常以S/N表示，一般用分贝(dB)为单位。

信噪比越高表示音频质量越好，一般音频光端机的信噪比应该在60dB以上。

误码率误码率(BER : Bit Error Ratio )是衡量数据在规定时间内数据传输精确性的指标。

误码率=传输中的误码/所传输的总码数*100%。

如果有误码就有误码率。

信号电平信号电平(signal level )是指设备输岀信号和输入信号的功率比然后取对数值，通常用P表示，P=lgP2/P1。

信号阻抗信号阻抗(Signal Inpedanee )是指输入信号的电压与电流的比值，单位通常是Q (欧姆)。

高清网络摄像机使用手册声明本手册可能在某些技术细节方面描述不够准确或存在印刷错误，假如您在使用过程中按照使用手册无法解决问题时，请致电我公司技术部垂询相关操作方法。

本手册的内容将做不定期的更新，恕不另行通知。

✋远离高温的热源和环境；避免阳光直接照射；✋为确保服务器的正常散热，应避开通风不良的场所，注意防水，防潮，防雷。

如需安装到户外，则需要安置防水箱，将服务器固定其中；✋本机应水平安装或壁挂安装，避免安装在会剧烈震动的场所，勿将其它设备放于本机上。

2、避免电击和失火✋切记勿用湿手触摸电源和服务器；✋勿将液体溅落在服务器上，以免造成机器内部短路或失火；✋勿将其它设备直接放置于本服务器上部；✋非专业人员请勿自行拆开机壳，避免损坏和电击；3、运输与搬运✋本机的包装经过抗震设计和实验，确保在运输过程中服务器不会受到意外损坏，所以在搬运本机时，最好使用原来的包装材料和纸箱；✋运输装有硬盘的服务器时，务必将硬盘固定安装在服务器内的硬盘卡位内，并用螺丝固定，否则可能会造成硬盘损伤而影响正常工作；✋避免在过冷、过热的场所间相互搬动服务器，以免机器内部产生结露，影响机器的使用寿命；✋严禁带电搬动本机，否则会损坏硬盘和主板；目录1 产品简介 (4)1.1产品简介 (4)1.2功能简介 (4)1.3技术规格 (4)2 外观与说明 (5)3 设备与安装 (7)3.1 运行环境 (7)3.2 设备安装 (7)4 IE 版客户端 (7)4.1 准备工作 (7)4.2 开始登陆 (7)4.3 功能简介 (8)4.3.1实时监视 (8)4.3.2录像回放 (10)4.3.3 参数设置 (11)4.3.3.1基本信息设置 (12)4.3.3.2网络参数设置 (15)4.3.3.3通道参数设置 (20)4.3.3.4报警参数设置 (24)4.3.3.5前端存储设置 (26)5.常见问题解答 (29)5.1无法通过浏览器访问网络摄像机 (29)5.2云台或球型摄像机不能控制 (30)5.3程序升级以后，无法正常播放视频 (30)5.4如何使网络摄像机在公网（Internet）上进行视频传输服务 (30)5.5为何正常数据不能通过交换机 (31)5.6为何升级后通过浏览器访问网络摄像机会出错 (31)6.附录 (32)附录A关于网络摄像机端口占用（映射）的问题说明 (32)附录B 出厂默认参数 (33)7.术语解释 (34)1产品简介1.1产品简介感谢您使用本公司产品，我们将向您提供最好的服务。

SFA CompaniesFuel Tank AdapterCapacity 80 lb.Model Number40080SAFETY and GENERAL INFORMATIONSave these instructions. For your safety read, understand, and follow the information provided with and on this device before using. The owner and operator of this equipment shall have an understanding of it and safe operating procedures before attempting to use. The owner and operator shall be aware that use of this product requires special skills and knowledge pertaining to bonding and grounding of personnel and components. Instructions and safety information shall be conveyed in the operator's native language before use of this product is authorized. If any doubt exists as to the safe and proper use of this device, remove from service immediately.Inspect before each use. Do not use if broken, bent, cracked, or damaged parts (including labels) are noted. Any ramp that appears damaged in any way, operates abnormally or is missing parts, shall be removed from service immediately. If you suspect that the ramp was subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately discontinue use until the ramp has been checked by a factory authorized service center (contact distributor or manufacturer for list of authorized service centers). It is recommended that an annual inspection bedone by qualified personnel. Labels and owner’s manuals are available from manufacturer.Omega Fuel Tank Adapter is designed for fuel tank removal and fuel tank installation. This Fuel Tank Adapter must ONLY be secured to Omega transmission jack model 41000 and 41001. It is designed for use with passenger cars and light trucks only.The Fuel Tank Adapter should only be used on METAL FUEL TANKS!Use of this product requires special skills and knowledge pertaining to grounding and Use ONLY on METAL FUEL TANKS!PRODUCT DESCRIPTIONArmRatchetSupport StandFigure 1 - Fuel Tank Adapter Components1. Remove saddle from the transmission jack.2. Drill two 7/16” size holes on the saddle. Ensure the holes are 9 1/2" apart and, should be located equally away from the saddle edges about 1” (Refer figures 2 & 3 for location of holes).Note: The integrity of your transmission jack should not be affected by these two holes as long as the instructions are followed. Omega will warrant its transmission jack original warranty for this specific fuel tank adapter installation.3. Secure the fuel tank adapter to the saddle with two 3/8”-24x1 1/2" bolts, flat washers, lock washers and nuts provided (Figure 4).(Refer to Figure 5 for below procedures)4. Slide support stand (1) over one end of the two arms (2). Repeat procedure on other end of same arm; Slide support stand (3) over one end of the other arm. Repeat procedure on other end of same arm.5. Secure each support stand by inserting snap pin (4) through the aligned holes on arm, snapping the latch over the end of pin as shown.6. Insert the 3/8"-16 x 2 1/2" Bolt (5) through the last set of holes in arm and 20x 1 hole.INSTALLATION (refer Figure 1 thru 5)Note: Below instruction is illustrating the use of fuel tank adapter conjunction with Model 41000 and 41001.Estimated Time: 30 minutesTools required: Drill, 7/16" drill bit, 17mm & 19mm wrenches.Fig. 3Fig. 2BEFORE USE1. Verify that the product and the application are compatible.2. Before using this product, read this fuel tank adapter manual, the transmission jack manual, and the vehicleservice manual completely. Familiarize yourself thoroughly with the product, its components, and recognize the potential hazards associated with its use.3. Locate and place a Class B fire extinguisher near the working area.4. Affix the fuel tank adapter to transmission jack properly before removing or installing the fuel tank.5. Bond the Fuel Tank Adapter to the transmission jack and to the fuel tank while grounding the transmission jack toearth before removing or installing the fuel tank. Operator must be bonded to both the jack and tank! If unsure how to provide proper grounding and bonding of personnel and equipment STOP, discontinue use, and seek the advice of qualified personnel.6. Replace worn or damaged parts and assemblies with factory authorized replacement parts only.7. Inspect before each use. Do not use if bent, broken or cracked components are noted.NO SMOKING!use fuel tank handler near open flame,heat sources or spark inducing environments.have a Class B fire extinguisherfuel from the vehicle fuel tank intoOperator must be bonded to both the jack and tank! If unsure how to provide proper bonding ofpersonnel and equipment STOP, discontinue use, and seek the advice of qualified personnel. BEFORE USE1. Verify that the product and the application are compatible, if in doubt call Omega Tech. Service (888) 332-6419.2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with theproduct and the hazards associated with its improper use.3. Inspect before each use. Do not use if bent, broken or cracked components are noted.4. Ensure that all parts move freely.OPERATIONRemoval of Fuel Tank (Refer to Figure 6)1. Read and follow the fuel tank removal/installation procedures as stated in the vehicle service manual.2. Drain the existing fuel into an approved and grounded fuel storage tank.3. Raise the transmission jack to directly underneath the designated fuel tank, refer to your transmission jack owner/operator’s manual for instructions on how to raise and lower the transmission jack.4. Clip one bonding cable to the fuel tank.5. Clip the other bonding cable to the transmission jack.6. Ground the transmission jack to earth.7. Center the fuel tank on all four of the Fuel Tank Adapter padded supports. For adjustment,:a. Open the latch of the safety snap pin and remove.b. Slide the support stand to the desired location.c. Re-insert safety snap pins through the holes in both the support stand and arm. Close the latch of snap pin.d. Adjust the opposite support stand to match the previously repositioned support stand.e. Ascertain that the load is centered with respect to the transmission jack.8. Place the safety nylon straps around the fuel tank, and hook them to the holes on the on support pads (refer toFigure 6 and Figure 5 side view ).9. Securely tighten using the ratchet.Note: To loosen the strap, pull the safety latch on the ratchet downward and rotate handle 180 degrees. When the strap has been fully opened, the strap may be pulled through the ratchet to take up excess slack. 10. Ascertain that the hooks stay in place while tightening with the ratchet. 11. Remove fuel tank according to the vehicle service manual.12. Lower the transmission jack to its lowest position before transporting the fuel tank.Operator must be bonded to both the jack and tank! If unsure how to provide proper bonding ofpersonnel and equipment STOP , discontinue use , and seek the advice of qualified personnel.Figure 6TROUBLESHOOTINGMAINTENANCEInspections should be made before each use of the Fuel Tank Adapter, checking for abnormal conditions.1. It is important to keep the product clean.2. Periodically wipe the product with an oily cloth.3. Inspect the product annually.StorageStore the fuel tank adapter in a clean, dry area when not in use.SFA Companies10939 N. Pomona Ave. Kansas City, MO 64153888-332-6419*******************REPLACEMENT PARTSNot all components of the Fuel Tank Adapter are replacement items, but are illustrated as a convenient reference of parts location. When ordering parts, give part number and parts description. Call or write for current pricing: SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A. Tel: (888) 332-6419 Fax: (816) 891-6599E-Mail:*******************************:Figure 7 - Replacement Parts Illustration for 4008012453SFA Companies10939 N. Pomona Ave. Kansas City, MO 64153888-332-6419*******************ONE YEAR LIMITED WARRANTYFor a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer’s exclusive remedy.Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas city, MO 64153 or to Omega Authorized dealer from which you purchased.Except where such limitations and exclusions are specifically prohibited by applicable law. (1) THE CONSUMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE. (2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION, ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY .Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.。