RMS产品使用手册

多功能电力仪表用户手册一、产品简介该系列产品是一种具有可编程测量、显示、数字通讯和电能脉冲变送输出等多功能智能仪表，能够完成电量测量、电能计量、数据显示、采集及传输，可广泛应用变电站自动化、配电自动化、智能建筑、企业内部的电能测量、管理、考核。

测量精度为0.5级，实现LED 现场显示和远程RS-485数字接口通讯，采用MODBUS-RTU通讯协议。

二、技术参数三、安装与接线1.1仪表尺寸96 96X 96 91X 91 96 96 95 8080*80 76*76 80 80 90 7272*7267*677272901.2 安装方法（1）在固定配电柜开开孔尺寸大小的孔； （2）取出仪表，松开螺丝，取下固定支架； （3）仪表由前插入安装孔；（4）插入仪表固定支架，并拧紧螺丝固定仪表。

1.3 端子接线图三相四线接线图三相三线接线图（注1：尺寸不同接线方式都相同）（注2：电流线星号为进线，进出线接反，电能计量到反相电能。

）四、编程操作4. 1进入和退出编程状态进入编程状态：在测量显示状态时按住“SET ”键1秒钟，进入密码认证页面，使用“<”键，“▲”键和“▼”键输 入密码（默认用户密码为1111），再按“SET ”键就进入编程状态页面。

注意：如果输入密码按SET ”键 后，退出到测量显示状态，则表示输入密码不正确。

退出编程状态：在编程状态，一直按住“SET ”键2秒钟，退出编程状态，会提示用户选择是否保存设置值，‘yes ”保存设 置值，“no ”不保存设置值。

按“SET ”键保存，按其它键不保存。

5. 2编程操作中按键的使用功能键SET ：确认设置值，进入下一项设置或退出设置。

位选键◄:循环选定要设置的数码管，选定的数码管呈闪烁状态。

增加键▲:改变闪烁位数码管的数值（数码管数值从0到9循环）。

减小键▼:改变闪烁位数码管的数值（数码管数值从9到0循环）。

6. 3设置参数说明序号序号内容说明 显示 范围UAA ----------B ----------C ----------- N ---------- |H | |1 2L NH 柞电黑甲甲甲甲甲甲甲甲甲1004 |rj 05'网UG UN [lA* 31A五、面板说明与测量信息显示2三相电流3有功功率、无功功率、功率因数4频率、第1到第4路开出信息、第1到第4路开入信息5有功电能5000K M O OV ▼ V vV A WHZ49 9 8 V AVarWh5.001 l vAPFvarh3.142 麻1009 v0952 VfHzAVarWhWHZAVarWhA PFVarhK M。

PN 4271782August 2012© 2012 Fluke Corporation. All rights reserved.All product names are trademarks of their respective companies.287/289True-rms Digital MultimetersSafety InformationGo to to register your product and find more information.A Warning identifies conditions and procedures that are dangerous to the user.WarningTo prevent possible electrical shock, fire, or personalinjury:•Read “Safety Information” before using this Meter. • Use this Meter only as specified in this manual or the protection provided by the Meter might beimpaired.• Do not use the Meter if it is damaged. Before you use the Meter, inspect the case. Look for cracksor missing plastic. Pay particular attention to theinsulation surrounding the connectors.• Make sure the battery door is closed and latched before operating the Meter.• Remove test leads from the Meter before opening the battery door.• Inspect the test leads for damaged insulation orexposed metal. Check the test leads forcontinuity. Replace damaged test leads beforeyou use the Meter.• Do not apply more than the rated voltage, as marked on the Meter, between the terminals orbetween any terminal and earth ground.• Never operate the Meter with the cover removed or the case open.• Use caution when working with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. These voltagespose a shock hazard.• Use only the replacement fuses specified by the manual.• Use the proper terminals, function, and range for measurements.•Avoid working alone.•When measuring current, turn off circuit power before connecting the Meter in the circuit.Remember to place the Meter in series with thecircuit.•When making electrical connections, connect the common test lead before connecting the live testlead; when disconnecting, disconnect the live test lead before disconnecting the common test lead. •Do not use the Meter if it operates abnormally.Protection may be impaired. When in doubt, havethe Meter serviced.•Do not operate the Meter around explosive gas, vapor, or dust.•Use only 1.5 V AA batteries, properly installed in the Meter case, to power the Meter.•When servicing the Meter, use only specified replacement parts.•When using probes, keep fingers behind the finger guards on the probes.•Do not use the Low Pass Filter option to verify the presence of hazardous voltages. Voltages greaterthan what is indicated may be present. First, makea voltage measurement without the filter to detectthe possible presence of hazardous voltage. Then select the filter function.•Only use test leads that have the same voltage, category, and amperage ratings as the meter andthat have been approved by a safety agency. •Use proper protective equipment, as required by local or national authorities when working inhazardous areas.•Comply with local and national safetyrequirements when working in hazardouslocations.•To avoid circuit damage and possibly blowing the Meter’s current fuse, do not place the probesacross (in parallel with) a powered circuit when alead is plugged into a current terminal. Thiscauses a short circuit because the resistancethrough the Meter's current terminals is very low. •To avoid possible electric shock or personal injury, do not use the Low Pass Filter option toverify the presence of hazardous voltages.Voltages greater than what is indicated may bepresent. First, make a voltage measurementwithout the filter to detect the possible presenceof hazardous voltage. Then select the filterfunction.•To avoid the potential for fire or electric shock, do not connect the thermocouple to electrically livecircuits.•To avoid damage to the Meter and possible injury, never attempt an in-circuit current measurementwhere the open-circuit potential to earth is greaterthan 1000 V.•To avoid electrical shock or personal injury,repairs or servicing not covered in this manualshould be performed only by qualified personnelas described in the 287/289 Service Information.•To avoid electrical shock or personal injury,remove the test leads and any input signalsbefore replacing the battery or fuses. To preventdamage or injury, install only Fluke specifiedreplacement fuses with the amperage, voltage,and speed ratings shown in the User’s Manual.•Do not exceed the Measurement Category (CAT) rating of the lowest rated individual component ofa Product, probe, or accessory.•Do not use the TL175 or TP175 test probes in CAT III or CAT IV environments without the probe tipfully extended and correct category rating visiblein the window.•When the TL175 is used with instruments or other accessories, the lowest category rating of thecombination applies. One exception is when theprobe is used with the AC172 or AC175.Safety SpecificationsBattery Type: 6 AA Alkaline batteries, NEDA 15A IEC LR6 Temperature:Operating: -20 °C to +55 °CStorage: -40 °C to +60 °CAltitude: Operating: 3000 m; Storage: 10,000 mFrequency Overload Protection: Input is limited to the product of a V rms sinewave times frequency of 2 x 107 V-Hz.SymbolsSymbol Description Risk of Danger. Important information. SeeManual.Hazardous voltage.Battery (Low battery when shown on the display)BatteryUnderwriters Laboratory listed productFuseInspected and licensed by TÜV Product ServicesAC (Alternating Current or Voltage)DC (Direct Current or Voltage)Continuity test or continuity beeper toneConforms to European Union directivesConforms to relevant North American SafetyStandards.Conforms to relevant Australian EMC requirements FuseCAT II Measurement Category II is applicable to test and measuring circuits connected directly to utilization points (socket outlets and similar points) of the low-voltage MAINS installation.CAT III Measurement Category III is applicable to test and measuring circuits connected to the distribution part of the building’s low-voltage MAINS installation.CAT IV Measurement Category IV is applicable to test and measuring circuits connected at the source of the building’s low-voltage MAINS installation.Double InsulationThis product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control Instrumentation" product. Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycling information.Lifetime Limited WarrantyEach Fluke 20, 70, 80, 170, 180 and 280 Series DMM will be freefrom defects in material and workmanship for its lifetime. As usedherein, “lifetime” is defined as seven years after Flukediscontinues manufacturing the product, but the warranty periodshall be at least ten years from the date of purchase. Thiswarranty does not cover fuses, disposable batteries, damage fromneglect, misuse, contamination, alteration, accident or abnormalconditions of operation or handling, including failures caused byuse outside of the product’s specifications, or normal wear andtear of mechanical components. This warranty covers the originalpurchaser only and is not transferable.For ten years from the date of purchase, this warranty also coversthe LCD. Thereafter, for the lifetime of the DMM, Fluke willreplace the LCD for a fee based on then current componentacquisition costs.To establish original ownership and prove date of purchase,please complete and return the registration card accompanyingthe product, or register your product on .Fluke will, at its option, repair at no charge, replace or refund thepurchase price of a defective product purchased through a Flukeauthorized sales outlet and at the applicable international price.Fluke reserves the right to charge for importation costs ofrepair/replacement parts if the product purchased in one countryis sent for repair elsewhere.If the product is defective, contact your nearest Fluke authorizedservice center to obtain return authorization information, thensend the product to that service center, with a description of thedifficulty, postage and insurance prepaid (FOB Destination). Flukeassumes no risk for damage in transit. Fluke will pay returntransportation for product repaired or replaced in-warranty. Beforemaking any non-warranty repair, Fluke will estimate cost andobtain authorization, then invoice you for repair and returntransportation.THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULARPURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE SHALLNOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTALOR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDINGLOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT AUTHORIZED TOEXTEND ANY DIFFERENT WARRANTY ON FLUKE’S BEHALF.Since some states do not allow the exclusion or limitation of animplied warranty or of incidental or consequential damages, thislimitation of liability may not apply to you. If any provision of thiswarranty is held invalid or unenforceable by a court or otherdecision-maker of competent jurisdiction, such holding will notaffect the validity or enforceability of any other provision.Fluke Corporation Fluke Europe B.V.P.O. Box 9090 P.O. Box 1186Everett, WA 98206-9090 5602 BD EindhovenU.S.A. TheNetherlands 6/07。

RMS Clamp-on Logger Model OM-SL-CL600 USER MANUALM-3443/0899FOR WARRANTY RETURNS, please have the followinginformation available BEFORE contacting OMEGA:1. P.O. number under which the product wasPURCHASED,2. Model and serial number of the product underwarranty, and3. Repair instructions and/or specific problemsrelative to the product.WARRANTY/DISCLAIMEROMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA's customers receive maximum coverage on each product.If the unit should malfunction, it must be returned to the factory for evaluation. OMEGA's Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will be repaired or replaced at no charge. OMEGA's WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of being damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA's control. Components which wear are not warranted, including but not limited to contact points, fuses, and triacs.OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence,indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential,incidental or special damages.CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a "Basic Component" under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/ DISCLAIMER language, and additionally,purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.RETURN REQUESTS/ INQUIRIESDirect all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.OMEGA's policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and engineering.OMEGA is a registered trademark of OMEGA ENGINEERING, INC.© Copyright 1996 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied,photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of OMEGA ENGINEERING, INC.FOR NON-WARRANTY REPAIRS , consult OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA:1. P.O. number to cover the COST of the repair,2. Model and serial number of product, and 3. Repair instructions and/or specific problems relative to the product.Table of ContentsWarning (4)International Electrical Symbols (4)Receiving Your Shipment (5)Packaging (5)Specifications (6)Features (8)Indicators and Buttons (8)Inputs and Outputs (9)Battery Installation (9)Operation (10)Software (10)Minimum Computer Requirements (10)Installation (10)Using The Software (11)Cleaning (11)WarningThese safety warnings are provided to ensure the safety of personnel and proper operation of the instrument.• Read the instruction manual completely and follow all the safety information before attempting to use or service this instrument.• Use caution on any circuit: Potentially high voltages and currents may be present and may pose a shock hazard.• Read the Safety Specifications section prior to using the current probe.Never exceed the maximum voltage ratings given.• Safety is the responsibility of the operator.• For maintenance, use only original replacement parts.• NEVER open the back of the instrument while connected to any circuit or input.• Replace any defective parts immediately.• NEVER use the Model OM-SL-CL600 on electrical conductors rated above 600 V in overvoltage category III (CAT III).International Electrical SymbolsThis symbol signifies that the Loggers are protected by double orreinforced insulation. Use only specified replacement parts whenservicing the instrument.This symbol signifies CAUTION! and requests that the user referto the user manual before using the instrument.For more information about the Logger, refer to disk 2: MAIN MANUALReceiving Your ShipmentUpon receiving your shipment, make sure that the contents are consistent with the packing list. Notify OMEGA of any missing items. If the equipment appears to be damaged, file a claim immediately with the carrier and notify OMEGA at once, giving a detailed description of any damage.PackagingThe Model OM-SL-CL600 includes the following:• User manual• One 9 V battery• Two 3½” disks containing the window-based download and graphic software and a generic user manual• Six ft. long RS232 cableSpecificationsELECTRICALNumber of Channels: 1Measurement Range: 0 to 600 ArmsInput Connection: Split jaw*Accuracy: 2% of readings + resolution (0-400A)5% of readings + resolution (400-600A)Resolution : 8 Bit (0.5 Arms)Scale Range Maximum Input Resolution100%600 Arms 4 Arms50%500 Arms 2 Arms25%250 Arms 1 Arms12.5%125 Arms0.5 ArmsSample Rate:4096/hr max; decreases by 50% each time memory is fullData Storage: 8192 readingsData Storage Technique: TXR™ Time Extension Recording™Power: 9V Alkaline NEDA 1604, 6LF22, 6LR61Battery Life Recording:Up to 1 year continuous recording @ 25°COutput: RS-232 via DB9 connector*Reference condition: 23°C ± 3K, 20 to 70% RH, Frequency 50/60Hz, No AC external magnetic Field, DC magnetic field ≤ 40A/m, centered conductor, battery voltage 9 V ± 10%.INDICATORSOperation Mode Indicator: One Red LED• Single Blink in stand-by mode• Double Blink in logging mode• Continuously on: Overload condition• No Blinks in OFF modeCONTROLS:One button used to start and stop recording sessions and to turn the data logger ON and OFF.ENVIRONMENTALOperating Temperature: -4 to + 158°F (-20 to +70°C)Storage Temperature: -4 to + 174°F (-20 to +80°C)Relative Humidity: 5 to 95% non-condensingTemperature Influence: 5 cts.MECHANICALSize: 9-1/4" x 4" x 1-5/8" (235 x 102 x 41mm)Weight (with battery): 17.1 oz.Maximum Conductor Size: 1 conductor 1.65” (42mm)2 conductors 1” (25.4mm) eachCase Material: Polycarbonate UL V0SAFETYWorking Voltage: IEC 1010-1, 600V, Cat IIIORDERING INFORMATIONRMS Clamp-On Logger ........................................Model OM-SL-CL600FeaturesModels OM-SL-CL600:Indicators and ButtonsThe data logger has one start/stop button and one indicator.The button is used to start and stop recordings and to turn the data logger on and off. The red LED indicates the status of the data logger; OFF, STANDBY or RECORDING.Inputs and OutputsInput to the logger is via a split jaw CT. The bottom of the data logger has a female 9 pin “D” shell serial connector used for data transmission from the data logger to your computer.Battery InstallationUnder normal conditions, the battery will last up to a year of continuous recording unless the logger is re-started very frequently.In the OFF mode, the logger puts almost no load on the battery. Use the OFF mode when the logger is not in use. Replace the battery once a year in normal use.If the logger will be used at temperatures below 32°F (0°C) or is frequently turned on and off, replace the battery every six to nine months.1. Make sure your logger is turned off (no light blinking) and allinputs are disconnected.2. Turn the data logger upside down. Unscrew the batterycompartment.3. Locate the two wire (red/black) battery connector and attach the9 V battery to it. Make sure that you observe polarity by lining upthe battery posts to the proper terminals on the connector.4. Once the connector is plugged onto the battery, insert the batteryinto the battery compartment.5. Close the battery compartment.Your data logger is now recording (LED blinking). Press the test button for 5 seconds to stop the instrumentNote: For long term storage, remove the battery to prevent discharge effects.OperationPosition the Model CL600 around the conductor to be measured. Be sure that the positioning of the CL600 allows the jaws to firmly close before beginning the recording session.Next, press the start/stop button on the front of the unit to begin the recording session. The indicator light will double blink to indicate that the recording session has started. When the recording session has been completed, press the start/stop button to end the recording. The indicator light will single blink to indicate that the recording session has ended and the unit is in stand-by. Remove the logger from the conductor and transport it to the computer for data downloading. See section 2 page 19 of the main manual for downloading.Note: If the LED is continuously lit. You are measuring a current above 600A. Unclamp the probe immediately.SoftwareMINIMUM COMPUTER REQUIREMENTSProcessor: 386 or higherRAM Storage: 4 MB minimumHard Drive Space:100K for application, approximately 200K for each stored file Environment: Windows 3.1 or Windows 95Port Access: 1 available 9 pin serial port1 parallel port for printer supportINSTALLATIONYour data logger software is supplied on a single 3½” floppy disk. To install the program on your Windows based computer, proceed as follows: The software is Multilanguage. A prompt will ask you to select the language at the end of the installation process.Windows 3.1 Systems1. Insert the floppy disk containing the data logger software in yourcomputer’s floppy drive (usually Drive A).2. From the Program Manager select “File” on the command line.3. Select “Run” from the pull-down menu and type a:setup in thedialog box then click on “OK”.4. The set up program will temporarily load onto your computer.5. Next the setup program will offer C:\DATALOG as location wherethe software will be installed. Click on “Next” to use this directory or type in a new name, then click on “Next”.6. A bar graph will appear showing the progress of installation. Wheninstallation is complete a message screen will appear stating that the program has been installed. Click on “OK”. You are now ready to use the data logger software.Windows 95 Systems1. Insert the floppy disk containing the data logger software in yourcomputer’s floppy drive (usually Drive A).2. Click on the “Start” button on the bottom left side of the screen.3. Select “Run” from the menu and type a:setup in the dialog box thenclick on “OK”.4. The setup program will temporarily load onto your computer.5. Next the setup program will offer C:\DATALOG as location wherethe software will be installed. Click on “Next” to use this directory or type in a new name, then click on “Next”.6. A bar graph will appear showing the progress of installation. Wheninstallation is complete a message screen will appear stating that the program has been installed. Click on “OK”. You are now ready to use the data logger software.USING THE SOFTWARELaunch the software and connect the RS232 cable from your computer from the logger.Select “FILE”, “Baud rate” and “1200”, then select “PORT”, Com1, Com2, Com3 or Com4 (see your computer manual). The logger must now communicate with your computer (ID number of the logger and number of points recorded displayed).Select download to display the graph. (Download takes about 90 seconds)CleaningThe body of the clamp should be cleaned with a cloth moistened with soapy water. Rinse with a cloth moistened with clean water. Do not use solvent.11OMEGAnet SM On-Line Service: Internete-mail:**************Servicing North America:USA:One Omega Drive, Box 4047ISO 9001 Certified Stamford, CT 06907-0047Tel: (203) 359-1660FAX: (203) 359-7700e-mail:**************Canada:976 BergarLaval (Quebec) H7L 5A1Tel: (514) 856-6928FAX: (514) 856-6886e-mail:****************For Immediate Technical or Application Assistance:USA and Canada:Sales Service: 1-800-826-6342 1-800-TC-OMEGA SMCustomer Service: 1-800-622-2378 / 1-800-622-BEST SMEngineering Service: 1-800-872-9436 / 1-800-USA-WHEN SMTELEX: 996404 EASYLINK 62968934 CABLE: OMEGAMexico and Tel: (95) 800-TC-OMEGA SM FAX: (95) 203-359-7807 Latin America:En Espanol: (203) 359-1660 ext: 2203e-mail:*****************Servicing Europe:Benelux:Postbus 8034,1180 LA Amstelveen, The NetherlandsTel: (31) 20 6418405FAX: (31) 20 6434643Toll Free in Benelux: 06 0993344e-mail:************Czech Republic:Ostravska 767, 733 01 KarvinaTel: 420 (69) 6311899FAX: 420 (69) 6311114e-mail:***************France:9, rue Denis Papin, 78190 TrappesTel: (33) 130-621-400FAX: (33) 130-699-120Toll Free/France: 0800-4-06342e-mail:**************** Germany/Austria:Daimlerstrasse 26, D-75392 Deckenpfronn, GermanyTel: 49 (07056) 3017FAX: 49 (07056) 8540Toll Free in Germany: 0130 11 21 66e-mail:*****************United Kingdom:25 Swannington Road,P.O. Box 7, Omega Drive, 150 9002 Certified Broughton Astley, Leicestershire,Irlam, Manchester,LE9 6TU, England M44 5EX, EnglandTel: 44 (1455) 285520Tel: 44 (161) 777-6611FAX: 44 (1455) 283912FAX: 44 (161) 777-6622Toll Free in England: 0800-488-488e-mail:************It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice. WARNING: These products are not designed for use in, and should not be used for, patient connected applications.Where Do I Find Everything I Need for Process Measurement and Control?OMEGA ... Of Course!TEMPERATURE οThermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies οWire: Thermocouple, RTD & Thermistor οCalibrators & Ice Point References οRecorders, Controllers & Process Monitors οInfrared PyrometersPRESSURE / STRAIN FORCE οTransducers & Strain GaugesοLoad Cells & Pressure GaugesοDisplacement TransducersοInstrumentation & AccessoriesFLOW / LEVEL οRotameters, Gas Mass Flowmeters & Flow Computers οAir Velocity IndicatorsοTurbine / Paddlewheel SystemsοTotalizers & Batch ControllerspH/CONDUCTIVITY οpH Electrodes, Testers & AccessoriesοBenchtop / Laboratory MetersοControllers, Calibrators, Simulators & PumpsοIndustrial pH & Conductivity EquipmentDATA ACQUISITION οData Acquisition & Engineering SoftwareοCommunications-Based Acquisition SystemsοPlug-in Cards for Apple, IBM & CompatiblesοDatalogging SystemsοRecorders, Printers & PlottersHEATERS οHeating CableοCartridge & Strip HeatersοImmersion & Band HeatersοFlexible HeatersοLaboratory HeatersENVIRONMENTAL MONITORING AND CONTROL οMetering & Control InstrumentationοRefractometersοPumps & TubingοAir, Soil & Water MonitorsοIndustrial Water & Wastewater Treatment 333333333333333333333333333333333ο pH, Conductivity & Dissolved Oxygen Instruments14。

产品处置声明 使用本产品或产品达到使用寿命期限后的非欧盟成员国家客户和第三方是恰当处置产 品废弃物的唯一责任人。任何个人、公司、组织或者机构在产品使用过程中不得违反 美国州法律、美国联邦法律、当地国家法律或国际法律对废弃物的规定。本特利内华 达公司不承担产品使用过程中或者达到寿命期限后废弃物处理的责任。
2.2.1 定位 ............................................................................................................................................... 5 2.2.2 安装 ............................................................................................................................................... 5 2.2.3 电缆布线 ..................................................................................................................................... 6 2.2.4 电缆导管布置 ........................................................................................................................... 6 2.2.5 铠装电缆布线 ........................................................................................................................... 6 2.2.6 互连电缆密封 ........................................................................................................................... 6 2.3 电源和信号连接 ................................................................................................................................ 7 2.3.1 3300 监测系统 .............................................................................................................................. 7 2.3.2 2201 监测系统 .............................................................................................................................. 7 2.3.3 3500 监测系统 .............................................................................................................................. 7 2.3.4 外部电源 ..................................................................................................................................... 8