最新压铸件表面处理颜色常用语 (中英文双语

A安装尺寸 install dimension凹模固定板 retainer plate凹模 female die, female mold, negative moldB备件 spare parts变质 modification变质剂 modification agent扒渣 slagging-off保温炉 holding furnace保压压力 dwell pressure表面缺陷 surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢 forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥 divider/blast cone分型面 mold parting/parting face/mold joint附页 attachment/appendix复位杆 reset bar(rod)附件故障 accessory覆盖剂 covering flux废金属料scrap浮渣cinder反射炉 reverberatory furnace废品 reject飞边joint flash仿真simulationG规格 specification/standard数值孔径 numerical aperture (N.A)固定段 segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽 blind scab硅SiliconH滑块 sliding block滑块部件 moving parts滑块退让 return/move back焊补 welding-on横浇道 runner合模 die locking横流道 runner回炉料foundry returns合型 mold assembling/closing/die locking合型力 die locking force化学成分不合格chemical consistence analysisJ 浇口套 sprue bush浇排道系统pouring system浇不足 misrun浇注 pouring浇注断裂interrupted pour浇道比 gating ratio浇包 ladle精整dressing and finishing精度 accuracy接口 connector击伤 shot damage金相组织 metallographic structure金属残液heel金相检验metallographic test金属型涂料 die coating/coating for metal mold加压速度 rate of pressure increasing间隙 clearance精炼refining精炼剂refining flux精密铸造 precision casting静置holding/stewing渗透 impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具 tool fixturesK壳体 housing开炉 blowing in孔洞缺陷cavity库存 inventoryL冷却 cooling冷却水管 cooling water pipe冷却耐压管 cooling pressure pipe冷却水管用密封圈 O-ring/sealing ring/gasket ring冷室卧式压铸机 horizontal (cold chamber) die casting machine 冷却系统 cooling system冷却水接口 cooling water connector冷裂 cold crack冷隔 cold lap铝 Aluminum裂纹 crack拉伤 caught casting拉杆孔 draw bar螺纹 screw/thread螺纹结构 screw structure螺纹公称直径(直径 diameter)公称尺寸(名义尺寸) specified size/nominal dimension漏油 leakage of oil棱边倒角 edge炉料 charge炉衬 furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕 bloom/flow line力学性能不合格 physical-mechanical characteristic abnormalM 毛坯 rough/blank毛坯铸件 rough casting毛刺 veining/burr模芯 core模框 frame模槽 mold channel模套 chase/bolster/frame模具钢 die steel模具图纸 mold drawing内浇口 in-gate冒口 riser/feeder head冒口浇注系统 feeder head gating system镁 Magnesium锰 Manganese密闭耐压系统 tightness testN 内浇道 in-gate镍 NickleP配油盘 pressure plate排气块 exhaust block排气槽 air vent排气孔 vent/venting channel排气塞 venting plug配合套圆形:fitting sleeve 方型: fitting case跑铝 aluminum slop out of mold喷射冶金 injecting metallurgy喷丸清理 shot blasting cleaning抛丸清理 wheel blasting cleaning偏析 segregation破坏性实验 destructive testQ取件机 extractor去除浇冒口 de-gating清铲 chipping缺陷铸件 defecting casting气孔 blowhole/gas cavity/pinhole/porosity 气孔缩 blowhole shrinkage去毛刺 de-burring去除氧化皮 de-scaling氢 Hydrogen清理 cleaningR 热处理 heat treatment热电偶测温孔 thermocouple well热电偶 thermocouple (TC)/pyod热裂 hot heating熔炼 smelting熔化率 melting rate熔炼损耗 total melting loss熔池 bath熔剂 flux熔渣 slagS 水管 water pipe三维造型 3 D三坐标测量仪 coordinate 3上模座板 upper clamping plate缩孔 shrinkage缩松 dispersed shrinkage疏松 porosity(dispersed shrinkage)渗漏 leakage缩陷 sink/sink in/depression试块 test block/test piece/coupon实时控制系统 real-time control system试模 de-buggingT 推板 push plate推杆 push rod推板导柱 push plate guide pillar推板导套 push plate guide sleeve凸模固定板 punch-retainer plate铜 copper钛 TitaniumW 网状裂纹 craze crack/crazing/checking 未浇满 poured shortX 型芯 core型腔 mold cavity镶拼处 splicing place斜导柱孔 hole of inclined guide pillar 楔紧块 wedge型芯弯曲 core bending下模座板 lowering clamping plate型芯固定板 core-retainer plateX 光射线检验 X-ray inspectionY 压铸机 die casting machine压室 pressure chamber压室止口(定位)尺寸 dimension/size压实 squeezing compaction压射 shot/injection压射冲头 injection piston(ram)/plunger 压铸型 die casting die压力铸造模具 die-casting die易损镶块 wear insert易损件 wearing parts预应力 pre-stress永久型 permanent mold硬点 hard spot溢流槽 over flow well印痕 indentation氧 Oxygen荧光检验 fluorescent testZ真空接口 vacuum connector真空排气管 vacuum exhaust block总接头 main connector中接头 middle connector直浇道 sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing 铸钢 cast steel支架 ejector housing/mold base leg造渣 slag forming真空熔炼 vacuum melting真空压铸 vacuum die casting/ evacuated die casting 增压 pressurization针孔 pinhole沾铝 adhesive aluminum直读光谱分析仪 direct-reading spectrograph转运包 transfer ladle转向器steering rack柴油式传动叉车 Diesel forklift复印机 copying machine服务器 Server绘图仪 Graphic plotter兼容机 compatible machine材料库 warehouse投影仪 projector半自动车床 semi-automatic lathe半自动立式钻床 drill machine表面粗度测量仪 surface roughness gauge布洛维硬度计 Brinell hardness gauge测氢仪 Hydrogen gauge叉车充电机 charger程控交换机 exchanger齿轮油泵 oil pump储气罐 accumulator tank电动葫芦 Gantry crane电动试压泵 press tester电动斜切机 bias cutter电子秤 weighing scale电子扫描仪 scanner吊斗 spoon hopper高压离心风机 combustion blower管道泵 process water pump烘箱 oven监控系统 monitoring system简易数控车床 digital lathe交流弧焊机 Are welder抛光机 polisher锯床 saw空压机 air compressor冷冻式干燥机 dryer红外线测温仪冷却塔 cooling tower立式带锯床 band saw滤油机 oil filter焊接机 welder模温机 die heater喷粉室回收设备 painter system平面磨床 grinder气动量仪 air gauge切割机 cut-off machine清洗机 washer散热器攻丝机 tapping machine台式光谱仪 spectrograph台式砂轮机 abrasive machine卧式液压拉床 broaching machine铣床 milling machine钻床 drilling machine液压机 hydraulic machine真空机 vacuum pump时效炉 aging furnace电阻炉 stress relief furnace探伤机 diagnostic machine加工中心 machining center车床 lathe钻削中心 drilling & cutting center别克 Buick切边机 trim press冷却塔循环泵 cooling tower pump循环水离心泵 process water pump脱模剂压送机 die lube station取件机 extractorFL充痒压铸系统 FL oxygen feed die cast system 装卸车 loader在建工程 construction in progress捡漏机 picker纸芯式滤油器paper element filter电磁阀 solenoid valve溢流阀spillover valve调速阀 speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀 float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing带防尘盖单列轴承single row bearing shielded急停按钮 scram button三相开关threephase switch行程开关 limit/travel switch断路器circuit breaker接触器 contactor中间继电器intermediate relay时间继电器 time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp 电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线 wire for sliding出模斜度 draft angle隔皮 bur掉肉 misrun研配 grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封) Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔 oil filter point牛皮纸 kraft/brown paper瓦楞纸 fluting paper崩料 charge downslide/collapse卡涉现象 interference phenomenon 机械加工余量 stocking复制模 replaced mould偏心距 offset distance抽大缸 pull tie bar料头 biscuit抽芯 loose core光整平滑度 flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒] casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架 (car) frame钣金 sheet metal测板 side plate内侧板Inner side plate焊钳soldering turret焊条 welding rod焊点 welding spot焊接机器人 welding robot寿命周期成本 life cycle cost前轴 fore/leading axle后翼子板 rear fender切削性能 cutting characteristic散热性能 heat dispersion耐磨性能 wear resistant property摩擦系数 friction coefficient灰铸铁 gray iron; graphitic cast iron过盈配合 tight/interference fit缸套 cylinder, sleeve, barrel tube pipe导轨面 guide way (face)铣刀盘 face milling cutter/facing cutter刀盘 tool pan/cutter head磨削余量 grinding allowance耐用性 endurance钝化 passivation刀尖圆弧 circular profile of knife point(刀具)主偏角 entering angle; plan angle弹性变形量 amount of elastic deformation燃烧室 combustion chamber磨屑 abrasive dust滤器芯 strainer core差速器 differential gear反冲减震器 recoiling shock absorber废气涡轮 exhaust turbine涡轮增压器 turbocharger增压盲区 turboloch喷油器 oil sprayer/atomizer汽化器 carburetor硬质合金刀具 carbide tipped tool精镗刀具 fine boring tool动力传动系统 power transmission systemspanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrenchcalipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床 side planer插床 slotting machine车刀 lathe tool车轮车床 car wheel lathe车削 turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化 age hardening气体硬化 air hardening空气韧化 air patterning退火 annealing阳极效应 anode effect阳极氧化处理 anodizing滚镀 barrel plating滚筒打光 barrel tumbling染黑法 blackening青熟脆性 blue shortness碳酸盐薄膜防锈法 bonderizing箱位退火 box annealing封箱渗碳 box carburizing辉面电镀 bright electroplating光辉热处理 bright heat treatment 旁路热处理 bypass heat treatment 化学电镀 chemical plating化学蒸镀 chemical vapor deposition 大气热处理 controlled atmosphere 锐角效应 corner effect儒缓放电 creeping discharge压花 embossing部分淬火 selective quenching。

aberration ⾊差atomization 雾化bank mark 斜料纹bite 咬⼊blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛⽩body wrinkle 侧壁皱纹breaking-in 冒⼝带⾁bubble 膜泡burn mark 糊斑burr ⽑边camber 翘曲cell ⽓泡center buckle 表⾯中部波皱check 细裂痕checking 龟裂chipping 修整表⾯缺陷clamp-off 铸件凹痕collapse 塌陷color mottle ⾊斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎⽚edge crack 裂边fading 退⾊filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling ⽑边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation ⽔锈indentation 压痕internal porosity 内部⽓孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘⽪状表⾯缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock ⿇点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表⾯划伤seam 裂痕shock line 模⼝挤痕short shot 充填不⾜shrinkage pool 凹孔sink mark 凹痕skin inclusion 表⽪折叠straightening 矫直streak 条状痕surface check 表⾯裂痕surface roughening 橘⽪状表⽪皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening ⽩化wrinkle 皱纹。

压铸件表面处理颜色常用语（中英文双语）珍珠叻(pearl nickel)金属产品丝印(silk screening on Metal parts)电彩锌(electric coloring zinc)珍珠铬(pearl chrome)移印(PAD printing)表调(Pre-dips)珍珠金(pearl gold)焗漆(baking enamel)磷化(phosphatizing)金(gold)镁合金阳极处理(anodizing)铬化(chromating)尼龙叻(satin nickel)新铝色(alusilber)钝化(passivating)哑灰(dull grey)无铬钝化(deactivator)古青(antique brass)闪银(sparkle silver)除漆剂(varnish remover)黑白(antique bronze)特(微)闪银[extra (light) sparkle silver]古红(antique copper )超幼银(super fine silver)黑胚抛光(as-cast polished)特幼银(extra fine silver)喷珍珠镍(painted pearl nickel)镁合金电镀化学镍DNC-MG (electroless Nickel plating) 喷珍珠铬(painted pearl chrome)镁合金非铬皮膜MAGPASS (Cr-Free passivation)砂铬(satin chrome) 光铬(bright chrome)电泳漆(electrophoretic coating)哑银灰(dull/Matte silver grey)氟/碳聚合物喷涂(KYNAR 500-PVF2 coatings)半哑粗(细)银[semi-dull coarse/fine silver]静电粉沫喷涂(electrostatics powder coatings)喷砂阳极处理(anodization of sand blast)聚氨酯漆喷涂(polyurethane coatings )磨光阳极染色(polishing anode dyeing)聚脂漆喷涂(polyester coatings)环氧树酯喷涂(epoxy coatings)普通焗漆(baking enamel coatings)高温厨具焗漆(Non-stick debron coatings)微弧氧化白色MAO (micro-arc oxidation white)微弧氧化灰色(MAO grey)微弧氧化黑色(MAO black)非铬化（灰色）[Cr-free passivation treatment (grey)]陶瓷氧化灰色(ceramic oxidation grey)陶瓷氧化黑色(ceramic oxidation black)无色磷化(环保)[clear phosphatization (unharmed to environment)]无色磷化(不环保)[clear phosphatization (harmed to environment)]喷砂+无色磷化(环保) [sand blasting + clear phosphatization (unharmed to environment) ]喷砂+无色磷化(不环保) [sand blasting + clear phosphatization (harmed to environment) ]无色铬化(clear chroming)彩色铬化(各色) (colored chroming)彩色钝化(各色) (colored passivation)和种间色(spacing color)光镍+银+透明大红色泳漆(bright nickel + silver + clear scarlet e-coatings)[ 电尼龙叻(10-20μm)，扫尼龙之后上光油(聚脂漆最少为50μm，光泽度为90) ] [satin nickel plated (10-20μm), brushed to satin surface and then clear lacquer (polyester clear lacquer min 50μm gloss 90) ] ;透明泳漆(clear e-coatings)透明蓝色泳漆(clear blue e-coatings)透明黑色泳漆(clear black e-coatings)黑色泳漆(不透明) [black e-coatings (unclear) ]金泳漆(gold e-coatings)光镍+扫尼龙+透明黄色泳漆(bright nickel + brushed to satin surface + clear yellow e-coatings)光镍+透明浅黄色泳漆(bright nickel + clear buff e-coatings )光镍+银+透明深黄色泳漆(bright nickel + silver + clear deep-yellow e-coatings) 光镍+透明红紫色泳漆(bright nickel + clear purple e-coatings)光镍+透明深紫色泳漆(bright nickel + clear amaranth e-coatings)光镍+扫尼龙+透明浅红色泳漆(bright nickel + brushed to satin surface + clear light-red e-coatings)光镍+透明红色泳漆(bright nickel + clear red e-coatings)光镍+银+透明大红色泳漆(bright nickel + silver + clear scarlet e-coatings)光镍+透明啡色泳漆(bright nickel + clear coffee e-coatings)光镍+透明深绿色泳漆(bright nickel + clear dark green e-coatings)六价铬(hexavalent chromium)三价铬(trivalent chromium)尼龙镍+透明泳漆(satin nickel + clear e-coatings)光青铜+透明泳漆(bright bronze + clear e-coatings)光青铜+扫尼龙+透明泳漆(bright bronze + brushed to satin surface + cleare-coatings)珍珠镍+透明泳漆(pearl nickel + clear e-coatings)珍珠镍+扫尼龙+透明泳漆(pearl nickel + brushed to satin surface + cleare-coatings)哑镍+透明泳漆(matte nickel + clear e-coatings)古青铜+透明泳漆(antique bronze + clear e-coatings)古青铜+哑泳漆(antique bronze + matte e-coatings)古红铜+透明泳漆(antique copper + clear e-coatings)古红铜+哑泳漆(antique copper + matte e-coatings)古黄铜+透明泳漆(antique brass + clear e-coatings)古黄铜+哑泳漆(antique brass + matte e-coatings)新古色+哑泳漆(neo-patina + matte e-coatings)古铜+哑泳漆(bronzed + matte e-coatings)物理汽相淀积钛/氮化钛涂层[PVD (physical vapor deposition) Ti/ TiN (titanium nitride) ]三价铬黑锌zinc electroplating + trivalent chromate (black)。

age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理。

压铸件表面处理颜色常用语（中英文双语）珍珠叻(pearl nickel)金属产品丝印(silk screening on Metal parts)电彩锌(electric coloring zinc)珍珠铬(pearl chrome)移印(PAD printing)表调(Pre-dips)珍珠金(pearl gold)焗漆(baking enamel)磷化(phosphatizing)金(gold)镁合金阳极处理(anodizing)铬化(chromating)尼龙叻(satin nickel)新铝色(alusilber)钝化(passivating)哑灰(dull grey)无铬钝化(deactivator)古青(antique brass)闪银(sparkle silver)除漆剂(varnish remover)黑白(antique bronze)特(微)闪银[extra (light) sparkle silver]古红(antique copper )超幼银(super fine silver)黑胚抛光(as-cast polished)特幼银(extra fine silver)喷珍珠镍(painted pearl nickel)镁合金电镀化学镍DNC-MG (electroless Nickel plating) 喷珍珠铬(painted pearl chrome)镁合金非铬皮膜MAGPASS (Cr-Free passivation)砂铬(satin chrome) 光铬(bright chrome)电泳漆(electrophoretic coating)哑银灰(dull/Matte silver grey)氟/碳聚合物喷涂(KYNAR 500-PVF2 coatings)半哑粗(细)银[semi-dull coarse/fine silver]静电粉沫喷涂(electrostatics powder coatings)喷砂阳极处理(anodization of sand blast)聚氨酯漆喷涂(polyurethane coatings )磨光阳极染色(polishing anode dyeing)聚脂漆喷涂(polyester coatings)环氧树酯喷涂(epoxy coatings)普通焗漆(baking enamel coatings)高温厨具焗漆(Non-stick debron coatings)微弧氧化白色MAO (micro-arc oxidation white)微弧氧化灰色(MAO grey)微弧氧化黑色(MAO black)非铬化（灰色）[Cr-free passivation treatment (grey)] 陶瓷氧化灰色(ceramic oxidation grey)陶瓷氧化黑色(ceramic oxidation black)无色磷化(环保)[clear phosphatization (unharmed to environment)]无色磷化(不环保)[clear phosphatization (harmed to environment)]喷砂+无色磷化(环保) [sand blasting + clear phosphatization (unharmed to environment) ]喷砂+无色磷化(不环保) [sand blasting + clear phosphatization (harmed to environment) ]无色铬化(clear chroming)彩色铬化(各色) (colored chroming)彩色钝化(各色) (colored passivation)和种间色(spacing color)光镍+银+透明大红色泳漆(bright nickel + silver + clear scarlet e-coatings)[ 电尼龙叻(10-20μm)，扫尼龙之后上光油(聚脂漆最少为50μm，光泽度为90) ] [satin nickel plated (10-20μm), brushed to satin surface and then clear lacquer (polyester clear lacquer min 50μm gloss 90) ] ;透明泳漆(clear e-coatings)透明蓝色泳漆(clear blue e-coatings)透明黑色泳漆(clear black e-coatings)黑色泳漆(不透明) [black e-coatings (unclear) ]金泳漆(gold e-coatings)光镍+扫尼龙+透明黄色泳漆(bright nickel + brushed to satin surface + clear yellow e-coatings)光镍+透明浅黄色泳漆(bright nickel + clear buff e-coatings )光镍+银+透明深黄色泳漆(bright nickel + silver + clear deep-yellow e-coatings) 光镍+透明红紫色泳漆(bright nickel + clear purple e-coatings)光镍+透明深紫色泳漆(bright nickel + clear amaranth e-coatings)光镍+扫尼龙+透明浅红色泳漆(bright nickel + brushed to satin surface + clear light-red e-coatings)光镍+透明红色泳漆(bright nickel + clear red e-coatings)光镍+银+透明大红色泳漆(bright nickel + silver + clear scarlet e-coatings)光镍+透明啡色泳漆(bright nickel + clear coffee e-coatings)光镍+透明深绿色泳漆(bright nickel + clear dark green e-coatings)六价铬(hexavalent chromium)三价铬(trivalent chromium)尼龙镍+透明泳漆(satin nickel + clear e-coatings)光青铜+透明泳漆(bright bronze + clear e-coatings)光青铜+扫尼龙+透明泳漆(bright bronze + brushed to satin surface + cleare-coatings)珍珠镍+透明泳漆(pearl nickel + clear e-coatings)珍珠镍+扫尼龙+透明泳漆(pearl nickel + brushed to satin surface + cleare-coatings)哑镍+透明泳漆(matte nickel + clear e-coatings)古青铜+透明泳漆(antique bronze + clear e-coatings)古青铜+哑泳漆(antique bronze + matte e-coatings)古红铜+透明泳漆(antique copper + clear e-coatings)古红铜+哑泳漆(antique copper + matte e-coatings)古黄铜+透明泳漆(antique brass + clear e-coatings)古黄铜+哑泳漆(antique brass + matte e-coatings)新古色+哑泳漆(neo-patina + matte e-coatings)古铜+哑泳漆(bronzed + matte e-coatings)物理汽相淀积钛/氮化钛涂层[PVD (physical vapor deposition) Ti/ TiN (titanium nitride) ]三价铬黑锌zinc electroplating + trivalent chromate (black)。

压铸件表面处理颜色常用语（中英文对照）珍珠叻(pearl nickel)金属产品丝印(silk screening on Metal parts)电彩锌 (electric coloring zinc)珍珠铬(pearl chrome)移印(PAD printing)表调(Pre-dips)珍珠金(pearl gold)焗漆(baking enamel)磷化(phosphatizing)金(gold)镁合金阳极处理(anodizing)铬化(chromating)尼龙叻(satin nickel)新铝色(alusilber)钝化(passivating)哑灰(dull grey)无铬钝化(deactivator)古青(antique brass)闪银(sparkle silver)除漆剂(varnish remover)黑白(antique bronze)特(微)闪银[extra (light) sparkle silver]古红(antique copper )超幼银(super fine silver)黑胚抛光(as-cast polished)特幼银(extra fine silver)喷珍珠镍(painted pearl nickel)镁合金电镀化学镍DNC-MG (electroless Nickel plating) 喷珍珠铬(painted pearl chrome)镁合金非铬皮膜MAGPASS (Cr-Free passivation) 砂铬 (satin chrome) 光铬(bright chrome)电泳漆(electrophoretic coating)哑银灰(dull/Matte silver grey)氟/碳聚合物喷涂(KYNAR 500-PVF2 coatings)半哑粗(细)银[semi-dull coarse/fine silver]静电粉沫喷涂(electrostatics powder coatings)喷砂阳极处理(anodization of sand blast)聚氨酯漆喷涂 (polyurethane coatings )磨光阳极染色(polishing anode dyeing)聚脂漆喷涂(polyester coatings)环氧树酯喷涂(epoxy coatings)普通焗漆(baking enamel coatings)高温厨具焗漆(Non-stick debron coatings)微弧氧化白色MAO (micro-arc oxidation white)微弧氧化灰色(MAO grey)微弧氧化黑色(MAO black)非铬化（灰色）[Cr-free passivation treatment (grey)]陶瓷氧化灰色(ceramic oxidation grey)陶瓷氧化黑色(ceramic oxidation black)无色磷化(环保)[clear phosphatization (unharmed to environment)]无色磷化(不环保)[clear phosphatization (harmed to environment)]喷砂+无色磷化(环保) [sand blasting + clear phosphatization (unharmed to environment) ]喷砂+无色磷化(不环保) [sand blasting + clear phosphatization (harmed to environment) ]无色铬化(clear chroming)彩色铬化(各色) (colored chroming)彩色钝化(各色) (colored passivation)和种间色(spacing color)光镍+银+透明大红色泳漆 (bright nickel + silver + clear scarlet e-coatings) [ 电尼龙叻(10-20μm)，扫尼龙之后上光油 (聚脂漆最少为50μm，光泽度为90) ] [satin nickel plated (10-20μm), brushed to satin surface and then clear lacquer (polyester clear lacquer min 50μm gloss 90) ] ;透明泳漆(clear e-coatings)透明蓝色泳漆(clear blue e-coatings)透明黑色泳漆(clear black e-coatings)黑色泳漆(不透明) [black e-coatings (unclear) ]金泳漆(gold e-coatings)光镍+扫尼龙+透明黄色泳漆(bright nickel + brushed to satin surface + clear yellow e-coatings)光镍+透明浅黄色泳漆(bright nickel + clear buff e-coatings )光镍+银+透明深黄色泳漆(bright nickel + silver + clear deep-yellow e-coatings)光镍+透明红紫色泳漆(bright nickel + clear purple e-coatings)光镍+透明深紫色泳漆(bright nickel + clear amaranth e-coatings)光镍+扫尼龙+透明浅红色泳漆(bright nickel + brushed to satin surface + clear light-red e-coatings)光镍+透明红色泳漆(bright nickel + clear red e-coatings)光镍+银+透明大红色泳漆(bright nickel + silver + clear scarlet e-coatings) 光镍+透明啡色泳漆(bright nickel + clear coffee e-coatings)光镍+透明深绿色泳漆(bright nickel + clear dark green e-coatings)六价铬 (hexavalent chromium)三价铬(trivalent chromium)尼龙镍+透明泳漆(satin nickel + clear e-coatings)光青铜+透明泳漆(bright bronze + clear e-coatings)光青铜+扫尼龙+透明泳漆(bright bronze + brushed to satin surface + cleare-coatings)珍珠镍+透明泳漆(pearl nickel + clear e-coatings)珍珠镍+扫尼龙+透明泳漆(pearl nickel + brushed to satin surface + cleare-coatings)哑镍+透明泳漆(matte nickel + clear e-coatings)古青铜+透明泳漆(antique bronze + clear e-coatings)古青铜+哑泳漆(antique bronze + matte e-coatings)古红铜+透明泳漆(antique copper + clear e-coatings)古红铜+哑泳漆(antique copper + matte e-coatings)古黄铜+透明泳漆(antique brass + clear e-coatings)古黄铜+哑泳漆(antique brass + matte e-coatings)新古色+哑泳漆(neo-patina + matte e-coatings)古铜+哑泳漆(bronzed + matte e-coatings)物理汽相淀积钛/氮化钛涂层 [PVD (physical vapor deposition) Ti/ TiN (titanium nitride) ]三价铬黑锌 zinc electroplating + trivalent chromate (black)。

五金行业中英对照一、表面处理中英文对照Finish:表面处理Aluminium coloured铝本色Antique black青古铜色Antique pewter古典白Antique silver coloured仿古银色Black nickel plated镀黑镍Blue matt蓝色亚光Brass plated镀铜Bright亮色Bright black亮黑色Bronzed and brushed棕色磨亚光Chrome coloured亮铬色Chrome plated镀铬Chrome plated matt镀铬拉丝Chrome plated polished镀铬抛光Clear透明Copper tinge lightened淡色调亮铜Galvanized电镀Gold coloured matt金色，拉丝Gold coloured polished金色，抛光Lacquered涂漆Matt拉丝Matt black黑色亚光Matt brushed拉丝,亚光Matt fluorescent拉丝，亮光Natural天然的Nickel coloured Natural coloured 镍色本色Nickel plated 镀镍Nickel plated brushed镀镍拉丝Nickal plated matt镀亚光Nickel plated matt brushed镀镍磨砂效果Nickel plated polished镀镍抛光Pewter coloured白蜡色Polished抛光Red matt红色亚光Silver coloured银色Silver coloured anodized银色，阳极电镀Silver coloured matt银色，拉丝Silver coloured matt anodized银色，拉丝，阳极电镀Silver metallized金属银色Stainless steel coloured不锈钢色Stainless steel coloured matt不锈钢色，拉丝Tinted染色Transparent透明White bright亮白色二、材料中英文对照Material:材料Aluminium铝Beech榉木Brass黄铜Carbon碳Cherry樱桃木Glass玻璃Maple枫木Leather 皮革Metal金属Mirror glass镜面玻璃Oak橡木Plastic 塑料Polycarbonate共聚聚乙烯塑料(聚碳酸脂) Rubber橡胶Procelain白瓷Soft rubber软橡胶Stainless steel 不锈钢Steel 钢质Wood 木质Walnut 胡桃木Wenge 柞木Zebrano斑马木Zinc alloy锌合金Stainless steel,quality 1.4301不锈钢1.4301型Stainless steel,quality1.4305不锈钢1.4305型三、安装中英文对照Installation:安装For clamp fixing用夹具安装For clip fixing 用夹子安装For drilling of doors给门打孔安装(开槽安装) For drilling of flaps 打孔安装上翻门For drilling of front panels打孔安装前面板For glue fixing 用胶固定For gluing in胶粘For hooking in 用钩安装For screw fixing 螺丝固定For screwing in 螺丝固定Wall mounting 墙式安装。

文案大全Assembly line 组装线 Layout 布置图Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管supervisor 课长 ME 制造工程师 MT 制造生技cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸front plate 前板traightener 整平机punching machine 冲床 robot 机械手 hydraulic 液压 rear plate 后板 chassis 基座 bezel panel 面板power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序material check list 物料检查表 work cell 工作间 trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车personnel resource department 人力资源部production department 生产部门 planning department 企划部 QC Section 品管科stamping factory 冲压厂 painting factory 烤漆厂 common equipment 常用设备 uncoiler and s machine 油压机 lathe 车床planer |'plein|刨床 miller 铣床 grinder 磨床 driller??床linear cutting 线切割 electrical sparkle 电火花 welder 电焊机staker=reviting machine 铆合机 position 职务 president 董事长general manager 总经理special assistant manager 特助 factory director 厂长 department director 部长deputy manager | =vice manager 副理section supervisor 课长deputy section supervisor =vice section superisor 副课长 group leader/supervisor 组长 line supervisor 线长 assistant manager 助理to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil 擦油 final inspection 终检 to connect material 接料 to reverse material 翻料 wet station 沾湿台 Tiana 天那水cleaning cloth 抹布 tname of a department 部门名称 a o load material 上料 to unload material 卸料to return material/stock to 退料 scraped |'skræpid|报废 scrape ..v.刮;削deficient purchase 来料不良 manufacture procedure 制程 deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch 刮伤 dents 压痕defective upsiding down 抽芽不良 defective to staking 铆合不良 embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力 education and training 教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓 dministration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screwhead螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模文案大全to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified 不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具文案大全figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap 切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetorysecond count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting departmentfor reference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingdepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory Listandphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料not included in physicalinventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明文案大全part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆文案大全edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）文案大全top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口文案大全H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection新品首件检查FAA first article assurance 首件确认TVR tool verification report模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management文案大全全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国文案大全A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionInspect 高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一文案大全TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形 rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shellcasting 壳模铸造foam forming ?泡成形sinterforging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形 warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具burnishing die 挤光模landedpositive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswtbending die 双折冷弯模具extrusion die 挤出模 palletizingdie 叠层模family mold 反套制品模具 plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具 pressuredie 压紧模fishtail die 鱼尾形模具 profiledie 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具solid forging die 整体锻模 splitforging die 拼合锻模split mold 双并式模具 spruelessmold 无注道残料模具squeezing die 挤压模stretch文案大全form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coilspring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢diaphragmgate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin顶出梢ejector plate 顶出板 ejector rod顶出杆ejector sleeve 顶出衬套 ejectorvalve 顶出阀eye bolt 环首螺栓 filling core椿入蕊film gate 薄膜形浇口 finger pin指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头headlesspunch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injectionram 压射柱塞inlay busher 嵌入衬套innerplunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockoutbar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套liftingpin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush活动衬套making die 打印冲子manifoldblock 歧管档块master plate 靠模样板matchplate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板movingbolster 换模保持装置moving bolster plate 可动侧模板文案大全。

铸造常用词中英文对照及解释铸造常用词中英文对照及简释1. 铸件后处理(post treatment of casting) [ 铸件] 对清理后的铸件进行热处理﹑整形﹑防锈处理和粗加工的过程。

铸件后处理是铸造生产的最后一道工序。

2. 铸件清理(cleaning of casting) [ 铸件] 将铸件从铸型中取出﹐清除掉本体以外的多余部分﹐并打磨精整铸件内外表面的过程。

主要工作有清除型芯和芯铁。

3. 铸造有色合金(cast non ferrous alloy) [ 铸造合金] 用以浇注铸件的有色合金(见有色金属)﹐是铸造合金中的一类。

主要有铸造铜合金﹑铸造铝合金﹑铸造镁合金等。

4. 浇注系统(gating system) [ 铸型] 为将液态金属引入铸型型腔而在铸型内开设的信道。

包括﹕浇口杯，直浇道，横浇道，内浇道。

5. 模样(pattern) [ 铸型] 仿真铸件形状形成铸型型腔的工艺装备或易耗件。

为保证形成符合要求的型腔﹐模样应具有足够的强度﹑刚度。

6. 冒口(riser) [ 铸型] 为避免铸件出现缺陷而附加在铸件上方或侧面的补充部分。

在铸型中﹐冒口的型腔是存贮液态金属的容器。

7. 芯盒(core box) [ 铸型] 将芯砂制成型芯的工艺装备。

可由木材﹑塑料﹑金属或其它材料制成。

8. 芯砂(core sand) [ 造型材料] 铸造生产中用于制造型芯的材料﹐一般由铸造砂﹑型砂黏结剂和辅加物等造型材料按一定的比例混合而成9. 型砂(molding sand) [ 造型材料] 在砂型铸造中用来造型的材料。

型砂一般由铸造砂﹑型砂黏结剂和辅加物等造型材料按一定的比例混合而成。

10. 型砂粘结剂(molding sand binder) [ 造型材料] 将松散的铸造砂粘结在一起使之成为型砂或芯砂的造型材料。

11. 再生砂(reclaimed sand) [ 造型材料] 铸造生产中经过处理基本上恢复了使用性能可以回用的旧砂。