飞机维修常用工具

飞机维修中各类工具中英文对照扳手Wrenches/套筒Sockets开口扳手Open End Wrenches梅花扳手Spline End Wrenches块扳手Crowfoot Wrenches开口/梅花扳手Combination Wrenches六角扳手Hex Wrenches平板棘轮扳手Slab Ratchet棘轮扳手Ratchet Wrenches力矩扳手Torque Wrenches管钳Pipe Wrenches活动扳手Adjustable Wrenches六角套筒Six Point Sockets梅花套筒Twelve Point Sockets万向套筒Universal Sockets转接头Adaptor套筒接杆Socket Extension万向转接头Universal Joint螺刀Screwdrivers快速螺刀Fast Screwdrivers仪表螺刀Electronic miniature Screwdrivers 十字头螺刀PILLIPS Screwdrivers磁性螺刀Magnetic Screwdrivers一字头螺刀Flat Tip Screwdrivers摇把Speeders钳Pliers尖嘴钳Needle Nose Pliers大力钳Locking Pliers保险丝钳Safety Wire Twisters鹰嘴钳Adjustable Joint Pliers插头钳Connector Plug剥线钳Wire Strippers鱼口钳Combination Slip-Joint Pliers 卡环钳Convertible Snap Ring Pliers 剪线钳Diagonal Cutters压线钳Wire Crimpers电气工具Electronic Tools矿灯Safety Lamb(Miner’s Lamb)手电Flashing Light对讲机Interphone电烙铁Electronic Iron耳机Earphone防静电手腕Static Wrist电池Battery充电器Charger扬声器Speaker电源插座Receptacle电枪Electronic Runner电钻Electronic Drills指挥棒Flashing Emergency Light超声波Ultrasonic测量工具Measuring Tools钢板尺Steel Rulers卷尺Tape Rulers螺旋卡尺Outside Micrometer塞尺Feeler(Thickness)Gauges量杯Measuring Cup游标卡尺Dial Caliper表Gauges三用表Multi Meter兆欧表Meg Ohm Meter杂项Diversiform反光镜Inspection Mirror放大镜Magnifier软杆双爪式机械手Flexible Two_claw Pick Up Tool 软杆磁棒Flexible Magnetic Pick Up Tool划刀Utility Knife刮刀Scraper Knife剪刀Snip(Scissor)锯Saw凿子Chisels錾子Punch三脚架Tripod(Spider)铜榔头Copper Hammer铁榔头Iron Hammer胶榔头Rubber Hammer弯勾Hook锉File镊子Nipper(Pliers)销钉插拔工具Pin Removal Tools 气枪Pneumatic Runner气钻Pneumatic Drills铆钉枪Rivet Gun注射器Injector(Squirt)滑油加油车Oil Cart液压油加油车Hydraulic Fluid Cart 注油枪Grease Gun抹布Dishcloth手套Glove绳索Rope工具箱Tools Kit工具架Tools Rack千斤顶Jack撬棒Tommy Bar工作梯Work Ladder砂轮Grinding wheel砂纸Sand paper胶带Adhesive Tape焊锡Soldering Tin拖把Tow Bar发光背心Flashing Vest护目镜Goggle(Blinkers)安全带Life Belt(Safety Belt)增补两用扳手CONBINATION SPANNER两用扳手套装COMBINATION SPANNER SET加长型两用扳手COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET 梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET两用棘轮扳手COMBINATION RATCHET SPANNER两用棘轮扳手套装COMBINATION RATCHET SPANNER SET1/4'连接物ADAPTOR1/4'组合支架工具COMBINATION HOLDING TOOL小型发光二极管MINIATURE LED LAMP活动扳手SINGLE OPEN ENDED SPANNER扳手套装MAGNETO SPANNER SET单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER双开口扳手DOUBLE OPEN ENDED SPANNER双开口扳手套装DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手PLARE NUT SPANNER（OPEN）半月型梅花扳手HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN 开口敲击扳手OPEN ENDED SLOGGING SPANNER梅花敲击扳手RING SLOGGING SPANNER高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER 直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）延长管EXTENSION TUBE爪型扳手CROWFOOT SPANNER两用活头扳手COMBINATION SWIVEL HEAD WRENCH活结T型扳手SWIVEL HANDLE WITH SLIDING T套筒扳手SOCKET WRENCH弯头套筒扳手ANGLED SOCKET WRENCH双头套筒扳手DOUBLE ENDED SOCKET WRENCH旋棒TOMMY BAR分节旋棒STEPPED TOMMY BAR3C把手套筒扳手SOCKET WRENCH WITH3C-HANDLET型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET钩头扳手HOCK SPANNER WITH LUG带销扳手PIN SPANNER可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE 1/4'标准六角套筒HEXAGON SOCKET1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET棘轮扳手RATCHETS套筒SOCKETS套筒套装SOCKETS SETS摩擦棘轮扳手FRICTION RATCHETS冲击工具IMPACT TOOLS旋具头BITS扭矩扳手TORQUE WRENCHES1/4梅花套筒SOCKET UD PROFILE1/4六角套筒星型套筒SOCKET FOR PROTRUDING HEAD SCREWS 1/4一字，十字，星型，六角旋具套筒1/4’双向棘轮套筒扳手1/4’REVERSIBLE RATCHETT柄棘轮扳手RATCHET WITH T-HANDLE手用棘轮头HAND RATCHET WITHOUT HANDLE1/4转3/8转换接头CONVERTER1/4TO3/8T型滑动头手柄TOMMY BAR WITH SLIDING T活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT EXTENSION1/4四方驱动连接头SQUARE-DRIVE COUPLER1/4万向接头UNIVERSAL JOINT活动头手柄SWIVEL HANDLE套筒固定夹SOCKET RAIL WITH MAGNETIC3/8一字，十字，星型，六角旋具套筒3/8六角套筒SOCKET HEXAGON3/83/8梅花套筒SOCKET UD PROFILE塑料棘轮扳手PLASTIC RATCHET旋具头接头BIT ADAPTOR旋具头棘轮扳手BIT RATCHET旋具头螺丝起子BIT SCREWDRIVER旋具头延长杆BIT EXTENSION旋具头SCREWDRIVER BITS风动套筒IMPACT SOCKET风动套筒附件ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON 摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE0.6-5.4NM3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS 3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH 3C米字螺丝起子3C星型螺丝起子3C球头六角螺丝起子5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS电工螺丝旗子ELECTRONIC SCREWDRIVER木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器MAGNETIZER AND DEMAGNETIZER方刃锥子SQUARE BLADED AWLT型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLET型六角扳手HEXAGON SOCKET KEY WITH T-HANDLE六角扳手HEXAGON SOCKET KEY加长六角扳手EXTRA LONG HEXAGON SOCKET KEY加长球头六角扳手六角扳手套装HEXAGON SOCKET KEY SETT型星形螺丝起子SCREWDRIVER WITH T-HANDLE曲柄螺丝起子CRANKED SCREWDRIVER量规GARGE车灯测电笔CAR LIGHT TESTER6-24伏测电笔VOLTAGE TESTER6-24V150-250伏测电笔VOLTAGE TESTER150-250V钳子3件套装PLIERS SET，3-PIECE万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH48PIECE 小钢丝钳SMALL COMBINATION PLIERS钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）强力钢丝钳POWER COMBINATION PLIERS塑料水口钳SIDE CUTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）电工剪钳ELECTRICIAN’S SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）杠杆剪钳LEVER-ACTION SIDE CUTTERS杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS核头钳TOWER PINCERS拨钉钳PINCERS平头钳FLAT NOSE PLIERS圆头钳ROUND NOSE PLIERS直头尖嘴钳LONG NOSE PLIERS弯头尖嘴钳钳TELEPHONE PLIERS强力尖嘴钳TRIPLE-FUNCTION PLIERS直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳MECHANICS PLIER ANGLED PATTERN偏口机修工钳MECHANICS PLIER OFFSET PATTERN30度平圆机修钳MECHANICS PLIER WITH30电缆刀CABLE KNIFE电工电缆刀ELECTRICIAN’S CABLE KNIFE防静电专用钳子电子钳ELECTRONIC PLIERS迷你电子钳MINIATURE ELECTRONIC PLIERS防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳电缆剪钳CABLE CUTTERS小型万用剪SMALL UNIVERSAL SCISSORS万用电缆刀UNIVERSAL CABLE KNIFE自动剥线钳STRIPPING PLIERS ANTOMATIC剥线钳STRIPPING PLIERS固定剥线钳STRIP-FIX STRIPPING PLIERS剥线工具WIRE STRIPPER高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳INSULATING VARNISH STRIPPER剥线刀WIRE STRIPPING KNIFE绝缘胶带INSULATING TAPE压线钳CRIMPING PLIERS锁把式压线钳LOCK-GRIP CRIMPING PLIERS端子压线钳WIRE END-SLEEVE PLIERS模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳MODULAR CRIMPING PLIERS精确压线钳PRECISION CRIMPING PLIERS外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头卡簧钳（孔用）大型/重型卡簧钳X型把X-GRIP大力钳LOCK-GRIP PLIERS平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳WIDE JAW LOCKING PLIERS滑行杆式大力钳LOCK-GRIP SLIDE CLAMP固定大力钳GRIP WRENCH FOR GLUEING机械工作台钳MACHINE WORKBENCH CLAMP焊接大力钳LOCK-GRIP WELDING CLAMP管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMPC型大力钳LOCK-GRIP C CLAMP水泵钳UNIVERSAL PLIERS（7种设置/5种设置）水泵钳WATER PUMP PLIERS特殊水泵钳SPECIAL WATER PUMP PLIERS可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER 高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳MINI CHAIN PIPE WRENCH链钳CHANIN PIPE WRENCH重型管子钳STILLSON PIPE WRENCH断线钳BOLT CUTTERS钳子套装（3件/4件/6件/8件）VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLSVDE绝缘标准符合DIN EN60900IEC60900：2004以及VDE680适合在高压区安全工作（AC1000V DC1500V）VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/六角）VDE绝缘起子套装电压传感器/电压测试器VOLTAGE DETECTOR/TESTER绝缘扭力扳手VDE TORQUE WRENCH绝缘双向棘轮扳手VDE REVERSIBLE RATCHET绝缘六角套筒VDE SOCKET HEXAGONAL绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKETT型绝缘扳手VDE T-HANDLE绝缘延长杆VDE EXTENSION绝缘电工工具组套（3件/8件/14件/108件）VED3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH3C HANDLE绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET 绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNERVDE绝缘钢锯HACKSAW绝缘电缆刀VDE CABLE KNIFE绝缘电缆剪CABLE SHEARS棘轮式绝缘电缆剪钳CABLE CUTTERSVDE绝缘电缆剪VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳VDE绝缘橡胶垫VDE RUBBER COVER SHEETVDE绝缘电工安全手套VDE ELECTRICIANS’S SAFETY GLOVES绝缘塑料夹VDE PLASTIC CLAMPS车轮扳手WHEEL WRENCHES十字扳手4WAY WHEEL WRENCH撬棒TYRE LEVER轮毂罩移除工具HUBCAP RENOVING TOOS配重钳BALANCE-WEINHT PLIERS制动弹簧钳BRAKE-SPRING PLIERS闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE油壶OIL CANS过滤器扳手UNIVERSAL FILTER WRENCH皮带钳PULLEY WRENCH阀门研磨机VALVE GRUNDER阀门研磨工具VALVE LAPPING TOOS油封钳VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE活塞环钳PISTON RING PLIERS软管夹钳HOSE CLIP PLIERS电极拉马BATTERY TERMINAL PULLER电池测试器BATTERY TESTER火花塞套筒SPARK PLUG SOCKET火花塞套筒扳手SPARK PLUG SOCKET WRENCH 火花塞刷SPARK-PLUG BRUSH特殊尖冲凿SPECIAL PIN PUNCH弹簧撑开器SPRING SPREADER球头拉拔器UNIVERSAL BALL JOINT REMOVER 通用罐UMIVERSAL CANISTER防冻测试器ANTI-FREEZE TESTER安装钳INSTALLATION PLIERS吸盘SUCTION LIFTER磁性拾取工具MAGNETIC PICK-UP TOOL金属片切割器NIBBER杠杆剪切机LEVER-ACTION TIN SNIPS打孔钳PUNCH PLIERS橡胶锤RUBBER HAMMER塑料锤PLASTIC HAMMER无后坐力锤RECOILLESS HAMMER钳工球头锤ENGINEERS’S BALL PEIN HAMMER钳工锤ENGINEERS’S HAMMER平面刮刀FLAT SCRAPER三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER密封刮刀GASKET SCRAPER平锉HAND FILE圆锉ROUND FILE三角锉TRIANGULAR FILE半圆锉HALF-ROUND FILE锉类6件套装中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW栓孔锯KEYHOLE SAW小金属锯SMALL METAL SAW小PUK钢锯PUK JUNIOR HACKSAWHOBBY锯台钳/台虎钳METALWORKING VICE（100/125/150mm）钢卷尺STEEL TAPE MEASURE（3米/5米/8米）阀塞尺VALVE FEELER GAUGE塞尺火花塞塞尺SPARK PLUG GAUGE螺纹规THREAD GAUGE游标卡尺POCKET VERNIER CALLIPER数显游标卡尺DIGITAL CALLIPER划线器SCRIBER镊子TWEEZERS十字镊子CROSSLOCK TWEEZERS螺钉取出器BOLT EXTRACTOR断螺钉取出器套装SCREW EXTRACTOR SET机械螺母破开器MECHANICAL NUT SPLITTER螺栓插入及取出器STUD INSERTER AND EXTRACTOR 丝锥THREAD FILE管子割刀PIPE CUTTER自动切割机AUTOMATIC PIPE CUTTER链式切管机CHAIN PIPE CUTTER虹吸扳手SIPHON TRAP PLIERS钢丝刷WIRE BRUSH锉刀清洁刷FILE CLEANING BRUSH裁缝剪TAILORS SCISSORS发光二极管井下检查灯LED INSPECTION LAMP井下检查灯INSPECTION LAMP发光二极管工作灯LED WORK LIGHT工程锤ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤ENGINEERS’BALL PEIN HAMMER桃木备用手柄SPARE HANDLE HICKORY工匠锤JOINERS’HAMMER ROTBAND-PLUS石匠锤CLUB HAMMER双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS 大锤SLEDGE HAMMER大碎石锤STONE SLEDGE HAMMER劈木锤WOOD SPLITTING HAMMER铺路锤PAVING HAMMER单板锤VENEER HAMMER磁性锤MAGNETIC HAMMER ROTBAND玻璃装配工锤GLAZIERS HAMMER炭化合金瓦锤CARBIDE TILE HAMMER羊角锤CLAW HAMMER电焊敲锤SCALING HAMMER ROTBAND-PLUS无弹力安全锤RECOILLESS HAMMER安全锤SAFETY HAMMER SOFT-PLUS塑料锤PLASTIC HAMMER橡皮锤RUBBER MALLET HARD尼龙锤NYLON HAMMER木锤WOOLEN MALLET铜锤COPPER HAMMER CLUB SHAPE铝锤ALUMINIUM HAMMER ROTBAND桶形铝锤LEAD HAMMER SARREL SHAPE冷凿锤COLD CHISEL HAMMER热凿锤HOT CHISEL HAMMER平底压摸锤SET HAMMER TOP PART压槽铁锤TOP FULLER上型模锤BOTTOM FULLER冲锤PUNCH HAMMER镰刀锤SCYTHE HAMMER锻工钳BLACKSMITH’S TONGS铆钉钳RIVETTING TONGS锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP 冲子组套DRIFT PUNCH SET铆钉装配器RIVET SETTER字母及数字冲子LETTER AND NUMBER PUNCHES装配冲子SETTING PUNCH撬杆PRVBAR起钉器NAIL FIFER OCTAGONAL撬棍CROWBAR通用拉马UNIVERSAL PULLER两爪拉马PULLER2-ARM PATTERN三爪拉马PULLER3-ARM PATTERN防腐蚀拉马COROSTOP PULLER PATTERN快速拉马QUICK-ACTION PULLER两爪液压拉马UNIVERSAL2-ARM PULLER拉马延长杆EXTENSION FOR PULLERS液压轴杆HYDRAULIC PRESSURE SPINDLE三爪液压拉马UNIVERSAL2-ARM PULLER拉马套装PULLER SET螺母劈开器NUT SPLITTER液压螺母劈开器NUT SPLITTER HYDRAULIC螺栓提取器STUD EXTRACTOR轴承提取器BALL BEARING EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTOR SET提取器INTERNAL EXTRACTOR冲击轴承拉马IMPACT BEARING PULLER汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE 分离拉马SEPARATOR PULLER轴承分离器BEARING SEPARATOR传动轴轴承拉马DRIVE SHAFT BEARING PULLER分离器及拉马套装SEPARATOR AND PULLER SET拉拔卡盘PULLING CHUCK液压泵HYDRAULIC PUMP液压手泵HYDRAULIC HAND PUMP液压工具拉马1.50PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器HYDRAULIC PRESS轮毂拉马WHEEL-HUB PULLER传动轴拉马DRIVE-SHAFT PULLER方向盘拉马STEERING-WHEEL PULLER装配叉DISMANTLING AND ASSEMBLY FORK球头拉拔器BALL JOINT PULLER三爪机滤扳手OIL FILTER HOOK弹簧撑SPRING SPREADER塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET法兰分离器FLANGE SEPARATORS轨距测量器TRACK ALIGNMENT GAUGE扳手WRENCHES管子切割器PIPE CUTTERS扩口工具FLARING TOOLS弯管机PIPE BENDERS管子工具PLUMBING TOOLS铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS管子清洁设备PIPE CLEANING EQUIPMENT弯管系统PIPE BENDING SYSTEMSSNAP管道扳手PIPE WRENCH ECK-SNAP钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES 管子修边器PIPE DEBURRING REAMER不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES 扩口工具套装FLARING TOOL SET BOERDEX钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机PIPE BENDER WITH ROLLER弯管钳PIPE BENDING PLIERS带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER手动弯管机MANUAL BENDING TOOL液压弯管机HYDRAULIC PIPE BENDER手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION管道矫直工具PIPE STRAIGHTENING TOOL金属片弯边钳SHEET METAL CRINPING PLIERS折边钳SEAMING PLIERS快速夹取扳手QUICK-CLAMP WRENCH夹管钳GRIPPING PLIERS分级扳手STEPPED KEY复合分级扳手COMBINATION STEPPED KEY铁皮剪TIN SNIPS/HOLE CUTTING SNIPS/PELICAN PATTERN SNIPS 断线钳BOLT CUTTER管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT排水管清洁器DRAIN PIPE CLEANER工作台几工作桌WORKBENCHES AND WORK TABLES工具车TOOL TROLLEYS工具柜TOOL CABINETS车间推车WORKSHOP TROLLEYS抽屉柜/箱DRAWER-CABINETS/BOXES衣柜/工作服柜WARDROBES矮橱LOWER CUPBOARD UNIT图纸夹DRAWING HOLDER电源面板PWER SUPPLY PANEL防酸放腐蚀工作台面板六边形工作台HEXAGONAL WORKBENCH带抽屉工作台WORKBENCH WITH DRAWER CABINET塑料抽屉插件PLASTIC DRAWER INSERT工作桌推车WORKSHOP TABLE TROLIEYS工作台WORKBENCH带背板工作台坚固推车TROUGH TROLLEY平板车PLATFORM TROLLEY带手柄平板车PLATFORM TROLLYE WITH HANDLE维护推车SERVICE TROLLEY带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST工具箱TOOL CHEST存放斗STORAGE TRAY卷纸架PAPER ROLL HOLDER垃圾桶WASTE BASKET移动架写字板LECTERN WORKTOP存储盒STORAGE BOXES带门库架CUPBOARD WITH SHELVING WITH DOORS开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS 存物柜LOCKER WITH HINGED DOORS滑门橱CUPBOARD WITH SLIDING DOORS电脑柜COMPUTER CABINET桌上设备DESK INSTALLATION移动电脑架PC STAION MOBILE电脑车间组合PC WORKPLACE COMBINATION更衣室条凳CHANGING CUBICLE SEAT BENCH安全橱SAFETY CUPBOARD衣橱CLOTHES LOCKER带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH消防员衣橱FIREFIGHTER’S CUPBOARD工具橱TOOL CABINET移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE 固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY 分类垃圾收集站WASTE-COLLECTION STATION CONTAINER 立式烟灰缸STAND ASHTRAYOCHSENKOPF系列斧头欧洲ILTIS型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS特殊工具KLANN汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扭距测试仪及设备TORQUE TESTER AND EQUIPMENT扭距倍增器TORQUE MULTIPLIERS扭距角度指示器TORQUE ANGLE INDICATORS特殊DREMO工具SPECIAL DREMO TOOLS DREMOMETER系列扭力工具DREMOMETER TOOLS扭距螺丝刀TORQUE SCREWDRIVERS扭距扳手/扭力扳手TORQUE WRENCHES电子扭距测试仪ELECTRONIC TORQUE TESTERDKD校准遵守DKD准则3-7/3-8/DIN EN ISO6789 RAHSOL DREMOTEC产品校准按照DIN EN ISO6789标准迷你型扭距扳手DREMOMETER MINIDREMOMETER高强度铝合金扭距扳手含：DREMOMETER1-12NM/10-100LBF.IN（塑料外表）DREMOMETER6-30NM/50-270LBF.INDREMOMETER8-40NM/70-350LBF.INDREMOMETER20-120NM/15-90LBF.FT DREMOMETER40-200NM/30-150LBF.FT DREMOMETER50-300NM/35-220LBF.FT DREMOMETER80-360NM/60-260LBF.FT DREMOMETER110-550NM/80-405LBF.FT DREMOMETER140-760NM/105-560LBF.FT DREMOMETER520-1000NM/380-730LBF.FT DREMOMETER750-2000NMDREMOMETER1500-3000NMDREMOMETER系列棘轮头RATCHET HEADS DREMOMTER 扭距限制接合器TORQUE LIMIT UNIT转角仪TORQUE ANGLE INDICATOR圆形插头式扭距扳手（覆盖围8-1000NM）开口扳子头OPEN END RTTING梅花扳子头RING END RTTING半开口梅花扳子头FLARED END FITTING棘轮头RATCHET HEAD四方头FIXED SQUARE HEAD方形插头式扭距扳手（覆盖围8-400NM）开口插头RECTANGULAR OPEN END RTTING梅花插头RECTANGULAR RING END RTTING半开口梅花插头RECTANGULAR FLARED END RTTINGTORCOFIX系列带四方驱动的扭距扳手TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K含：4549-011-5NM1/4’方头4549-022-25NM1/4’方头4549-055-50NM3/8’方头4550-1010-100NM1/2’方头4550-2020-200NM1/2’方头4550-3060-300NM1/2’方头4550-4075-400NM1/2’方头4550-55100-550NM3/4’方头4550-75140-750NM3/4’方头TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SETTORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K蘑菇头MUSHROOM HEADTORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX Z TORCOFIX SE扭距扳手（四方插头）TORQUE WRENCH TORCOFIX SE TORCOFIX FS扭距扳手（可预设扭力值2-200NM）TORQUE WRENCH TORCOFIX FSTORCOFIX UK扭距扳手TORCOFIX UK TORQUE WRENCHTORCOFIX K扭距扳手TORCOFIX K TORQUE WRENCH扭距螺丝刀/扭力螺丝起子TORQUE SCREWDRIVERSFS型扭距螺丝刀围0.02-13.6NMS型扭距螺丝刀围0.05-9NMSP型扭距螺丝刀围10-500CNMTSN预置扭距滑转扳手TSN SLIPPER QORQUE WRENCH围3-125NM TBN折弯式扭距扳手TBN BREAKER QORQUE WRENCH围0.2-135NMTSP预置扭距滑转扳手TSP SLIPPER QORQUE WRENCH围1-10NM TSC预置扭距滑转扳手TSC SLIPPER QORQUE WRENCH围1-10NM 电线标示系统PLASTIC-TAG MARKING SYSTEM刻度盘/表盘扭距扳手DIAL MEASUREMENT TORQUE WRENCHES适用场合：测试控制维护工作应用环境ADS40.8-4NM1/4’方头ADS12D 2.4-12NM1/4’方头ADS255-25NM3/8’方头ADS408-40NM3/8’方头BDS80E16-80NM1/2’方头BDS20040-200NM1/2’方头CDS400S80-400NM3/4’方头DDS800S160-800NM3/4’方头EDS1400S280-1400NM1’方头EDS2000S400-2000NM1’方头88型折弯式扭距扳手TYPE88BREAKER TORQUE WRENCH围100-1500NM8800-013/4’方头100-500NM8800-023/4’方头150-700NM8800-033/4’方头300-1000NM8800-043/4’方头700-1500NM8800-06圆形插头16mm130-550NM扭距倍增器/扭力放大器/齿轮减速器TORQUE MULTIPLIERS在狭小的空间获得巨大的扭距输出型号不同围含1000NM-47500NM比例有1：51：151：15.51：251：261：751：125等等数字扭距扳手/数显扭力扳手ELECTRONIC TORQUE WRENCHE-TORC微处理器控制扭距扳手E-TORC ELECTRONIC TORQUE WRENCHTORCOTRONIC数显扭距扳手TORCOTRONIC ELECTRONIC TORQUE WRENCH电子扭距测试仪ELECTRONIC TORSIONS TORQUE TESTER E-TP智能型电子扭距测试仪系列E-TP ELECTRONIC TORSIONS TORQUE TESTER围包括：0.5-1000NM 的测试扭距扳手测试架TORQUE WRENCH TEST FRAMEE-TP打印机E-TP PRINTERE-TP固定架E-TP ADAPTER PLATEE-TP转接器E-TP ADAPTORE-TP软件及数据线E-TP SOFTWARE INCL AND PC-CONNECTION CABLE E-TP包装箱E-TP PLASTIC-CASE。

飞机机翼维修工具使用说明书1. 引言飞机机翼是飞行器的重要组成部分，其安全性和完整性对飞行安全至关重要。

因此，为了保障飞机的正常运行，机翼的维修和保养工作必不可少。

本文将详细介绍飞机机翼维修工具的使用方法，以帮助维修人员正确高效地进行机翼维护。

2. 工具准备在进行机翼维修工作之前，需要准备以下工具：- 扳手：用于拆卸和安装机翼上的螺栓和螺母。

- 砂纸和砂轮：用于清洁和修复机翼表面的损伤。

- 铝合金钉枪：用于固定机翼上的铝合金板。

- 焊接机：用于修复机翼上的金属结构。

- 温度计：用于监测机翼表面和内部的温度变化。

3. 工具使用方法3.1 扳手的使用方法- 使用正确尺寸的扳手，将其插入螺栓或螺母的头部。

- 逆时针旋转扳手，拆下或安装螺栓或螺母。

3.2 砂纸和砂轮的使用方法- 使用粗砂纸或砂轮，清洁机翼表面的污垢和涂层。

- 使用细砂纸或砂轮，修复机翼表面的轻微划痕和损伤。

3.3 铝合金钉枪的使用方法- 选择适当的钉子规格，并将其插入钉枪。

- 将铝合金板对准机翼位置，使用钉枪将钉子固定在机翼上。

- 确保钉子处于正确的深度，以防止损坏机翼表面。

3.4 焊接机的使用方法- 清洁和准备焊接区域，确保无杂质存在。

- 调整焊接机的电流和温度设置。

- 将焊接机的焊接头对准焊接区域，开始焊接操作。

- 注意焊接结束后的冷却时间，以避免热引起的损伤。

3.5 温度计的使用方法- 将温度计的探头对准机翼表面或内部。

- 确保温度计读数的准确性和稳定性。

- 监测温度变化，并及时采取必要措施，以避免过高或过低的温度对机翼造成损害。

4. 安全注意事项- 在使用任何工具之前，确保自身和周围环境的安全。

- 仔细阅读并遵守每个工具的操作手册和安全准则。

- 在使用焊接机和温度计时，注意防护措施，以免对人体和机翼造成伤害。

- 在工具使用完毕后，将其妥善保管并存放在安全位置，以防止丢失和损坏。

5. 结论本说明书详细介绍了飞机机翼维修工具的使用方法，希望能为维修人员提供有效的指导。

航空行业飞机维修工具说明书首章：前言本维修工具说明书旨在介绍航空行业中常用的飞机维修工具，以便维修人员能够正确使用和操作这些工具，确保飞机的安全和可靠性。

第一节：工具概述本节将对飞机维修工具的种类和功能进行概述，帮助维修人员对工具有一个整体的了解。

1.1 工具分类根据不同的维修任务和使用频率，飞机维修工具可以分为通用工具、专用工具和特殊工具三类。

1.1.1 通用工具通用工具是指可以用于多个维修任务的基础工具，如螺丝刀、扳手、钳子等。

这些工具在飞机维修过程中经常使用，维修人员应熟悉并掌握其正确使用方法。

1.1.2 专用工具专用工具是针对特定维修任务设计和制造的工具，如飞机钻孔机、精密测试仪器等。

这些工具通常由专门的制造商生产，并且使用时需要按照相应的操作手册进行操作。

1.1.3 特殊工具特殊工具是针对特殊情况下的维修任务设计和制造的工具，如航空救生工具、火灾控制工具等。

这些工具的使用通常需要特殊的许可和培训，维修人员在使用时需要严格遵守相关的规定和流程。

1.2 工具功能飞机维修工具的功能多种多样，包括但不限于拧紧螺栓、检测电路、修复液压系统等。

为了确保维修任务的进行，维修人员应熟悉各种工具的功能和使用方法。

第二节：工具清单本节将列出常用的飞机维修工具清单，并对每种工具的功能和使用要点进行详细介绍。

2.1 通用工具清单- 螺丝刀：用于拆卸飞机部件上的螺钉，常见的有十字螺丝刀、平头螺丝刀等。

- 扳手：用于拧紧和松螺母，根据不同的情况可以选择活动扳手、定扳手等。

- 钳子：用于夹紧零部件，常见的有直嘴钳、圆嘴钳等。

...2.2 专用工具清单- 飞机钻孔机：用于在飞机结构上钻孔，具有更高的精度和稳定性。

- 精密测试仪器：用于测试飞机系统的性能和故障，常见的有多功能测试仪、电子测量计等。

...2.3 特殊工具清单- 航空救生工具：用于紧急情况下的人员救生和逃生，包括安全绳、降落伞等。

- 火灾控制工具：用于航空器火灾的控制和灭火，常见的有灭火器、火焰喷洒系统等。

航空器维修设备表1. 简介本文档列出了航空器维修过程中所需的各种维修设备。

这些设备是确保航空器安全运行和维护的关键工具。

维修人员应根据需要使用这些设备，以确保维修工作的高效和准确性。

2. 设备列表以下是航空器维修过程中常用的维修设备：1. 螺丝刀套装：包括不同尺寸和类型的螺丝刀，用于拆卸和安装各种航空器部件。

2. 扳手套装：包括不同尺寸的扳手，用于紧固和松开螺栓和螺母。

3. 气动工具：包括气动钻、气动砂轮等，用于加工和修复航空器的金属部件。

4. 高压气源：用于供应气动工具所需的高压气体。

5. 焊接设备：包括电弧焊机和气体焊接设备，用于金属焊接和修复。

6. 测量工具：包括千分尺、卷尺等，用于测量各种航空器部件的尺寸。

7. 检测设备：包括超声波检测仪、磁粉检测仪等，用于发现潜在的航空器结构缺陷。

8. 电气测试设备：包括万用表、电源电压测试仪等，用于检测和排除航空器电气系统故障。

9. 清洁设备：包括各种清洁剂、刷子等，用于清洁航空器表面和部件。

10. 安全设备：包括安全帽、护目镜、防护手套等，用于保护维修人员的安全。

以上设备列表仅为参考，并不是详尽无遗。

实际使用中，维修人员应根据具体情况和要求，选择合适的设备进行维修工作。

3. 维修设备的管理为了确保维修设备的有效使用和管理，以下是一些管理措施建议：1. 定期检查设备：定期检查维修设备的完好状态，确保设备正常工作，并及时修理或更换损坏的设备。

2. 建立设备借用系统：建立设备借用系统，记录设备的借用情况和归还情况，以确保设备的正常流转和使用。

3. 培训维修人员：为维修人员提供设备使用培训，确保其正确、安全地使用维修设备。

4. 设备存放和保护：妥善存放维修设备，避免受潮、受热或受损，保护设备的寿命和性能。

维修设备的管理对于航空器的安全和维护至关重要。

维修人员应遵守相关规定和要求，正确使用和管理维修设备。

4. 结论航空器维修设备表是维修人员在航空器维修过程中参考的重要工具。

飞机维修中各类工具中英文对照扳手Wrenches/套筒Sockets开口扳手Open End Wrenches梅花扳手Spline End Wrenches块扳手Crowfoot Wrenches开口/梅花扳手Combination Wrenches内六角扳手Hex Wrenches平板棘轮扳手Slab Ratchet棘轮扳手Ratchet Wrenches力矩扳手Torque Wrenches管钳Pipe Wrenches活动扳手Adjustable Wrenches六角套筒Six Point Sockets梅花套筒Twelve Point Sockets万向套筒Universal Sockets转接头Adaptor套筒接杆Socket Extension万向转接头Universal Joint螺刀Screwdrivers快速螺刀Fast Screwdrivers仪表螺刀Electronic miniature Screwdrivers 十字头螺刀PILLIPS Screwdrivers磁性螺刀Magnetic Screwdrivers一字头螺刀Flat Tip Screwdrivers摇把Speeders钳Pliers尖嘴钳Needle Nose Pliers大力钳Locking Pliers保险丝钳Safety Wire Twisters鹰嘴钳Adjustable Joint Pliers插头钳Connector Plug剥线钳Wire Strippers鱼口钳Combination Slip-Joint Pliers卡环钳Convertible Snap Ring Pliers剪线钳Diagonal Cutters压线钳Wire Crimpers电气工具Electronic Tools矿灯Safety Lamb (Miner’s Lamb)手电Flashing Light对讲机Interphone电烙铁Electronic Iron耳机Earphone防静电手腕Static Wrist电池Battery充电器Charger扬声器Speaker电源插座Receptacle电枪Electronic Runner电钻Electronic Drills指挥棒Flashing Emergency Light超声波Ultrasonic测量工具Measuring Tools钢板尺Steel Rulers卷尺Tape Rulers螺旋卡尺Outside Micrometer塞尺Feeler (Thickness) Gauges量杯Measuring Cup游标卡尺Dial Caliper表Gauges三用表Multi Meter兆欧表Meg Ohm Meter杂项Diversiform反光镜Inspection Mirror放大镜Magnifier软杆双爪式机械手Flexible Two_claw Pick Up Tool 软杆磁棒Flexible Magnetic Pick Up Tool 划刀Utility Knife刮刀Scraper Knife剪刀Snip (Scissor)锯Saw凿子Chisels錾子Punch三脚架Tripod (Spider)铜榔头Copper Hammer铁榔头Iron Hammer胶榔头Rubber Hammer弯勾Hook锉File镊子Nipper (Pliers)销钉插拔工具Pin Removal Tools气枪Pneumatic Runner气钻Pneumatic Drills铆钉枪Rivet Gun注射器Injector (Squirt)滑油加油车Oil Cart液压油加油车Hydraulic Fluid Cart注油枪Grease Gun抹布Dishcloth手套Glove绳索Rope工具箱Tools Kit工具架Tools Rack千斤顶Jack撬棒Tommy Bar工作梯Work Ladder砂轮Grinding wheel砂纸Sand paper胶带Adhesive Tape焊锡Soldering Tin拖把Tow Bar发光背心Flashing Vest护目镜Goggle (Blinkers)安全带Life Belt(Safety Belt)增补两用扳手CONBINATION SPANNER两用扳手套装COMBINATION SPANNER SET加长型两用扳手COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET 梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET两用棘轮扳手COMBINATION RATCHET SPANNER两用棘轮扳手套装COMBINATION RATCHET SPANNER SET1/4'连接物ADAPTOR 1/4'组合支架工具COMBINATION HOLDING TOOL小型发光二极管MINIATURE LED LAMP活动扳手SINGLE OPEN ENDED SPANNER扳手套装MAGNETO SPANNER SET单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER双开口扳手DOUBLE OPEN ENDED SPANNER双开口扳手套装DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手PLARE NUT SPANNER（OPEN）半月型梅花扳手HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN 开口敲击扳手OPEN ENDED SLOGGING SPANNER梅花敲击扳手RING SLOGGING SPANNER高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）延长管EXTENSION TUBE爪型扳手CROWFOOT SPANNER两用活头扳手COMBINATION SWIVEL HEAD WRENCH活结T型扳手SWIVEL HANDLE WITH SLIDING T套筒扳手SOCKET WRENCH弯头套筒扳手ANGLED SOCKET WRENCH双头套筒扳手DOUBLE ENDED SOCKET WRENCH旋棒TOMMY BAR分节旋棒STEPPED TOMMY BAR3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLET型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET 钩头扳手HOCK SPANNER WITH LUG带销扳手PIN SPANNER可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE1/4'标准六角套筒HEXAGON SOCKET1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET棘轮扳手RATCHETS套筒SOCKETS套筒套装SOCKETS SETS摩擦棘轮扳手FRICTION RATCHETS冲击工具IMPACT TOOLS旋具头BITS扭矩扳手TORQUE WRENCHES1/4梅花套筒SOCKET UD PROFILE1/4六角套筒星型套筒SOCKET FOR PROTRUDING HEAD SCREWS1/4一字，十字，星型，内六角旋具套筒1/4’双向棘轮套筒扳手1/4’REVERSIBLE RATCHETT柄棘轮扳手RATCHET WITH T-HANDLE手用棘轮头HAND RATCHET WITHOUT HANDLE1/4转3/8转换接头CONVERTER 1/4 TO 3/8T型滑动头手柄TOMMY BAR WITH SLIDING T活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT EXTENSION1/4四方驱动连接头SQUARE-DRIVE COUPLER1/4万向接头UNIVERSAL JOINT活动头手柄SWIVEL HANDLE套筒固定夹SOCKET RAIL WITH MAGNETIC3/8一字，十字，星型，内六角旋具套筒3/8六角套筒SOCKET HEXAGON 3/83/8梅花套筒SOCKET UD PROFILE塑料棘轮扳手PLASTIC RATCHET旋具头接头BIT ADAPTOR旋具头棘轮扳手BIT RATCHET旋具头螺丝起子BIT SCREWDRIVER旋具头延长杆BIT EXTENSION旋具头SCREWDRIVER BITS风动套筒IMPACT SOCKET风动套筒附件ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING 安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH3C米字螺丝起子3C星型螺丝起子3C球头六角螺丝起子5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS电工螺丝旗子ELECTRONIC SCREWDRIVER木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器MAGNETIZER AND DEMAGNETIZER方刃锥子SQUARE BLADED AWLT型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLET型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE内六角扳手HEXAGON SOCKET KEY加长内六角扳手EXTRA LONG HEXAGON SOCKET KEY加长球头内六角扳手内六角扳手套装HEXAGON SOCKET KEY SETT型星形螺丝起子SCREWDRIVER WITH T-HANDLE曲柄螺丝起子CRANKED SCREWDRIVER量规GARGE车灯测电笔CAR LIGHT TESTER6-24伏测电笔VOLTAGE TESTER 6-24V150-250伏测电笔VOLTAGE TESTER 150-250V钳子3件套装PLIERS SET，3-PIECE万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE 小钢丝钳SMALL COMBINATION PLIERS钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）强力钢丝钳POWER COMBINATION PLIERS塑料水口钳SIDE CUTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）电工剪钳ELECTRICIAN’S SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）杠杆剪钳LEVER-ACTION SIDE CUTTERS杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS核头钳TOWER PINCERS拨钉钳PINCERS平头钳FLAT NOSE PLIERS圆头钳ROUND NOSE PLIERS直头尖嘴钳LONG NOSE PLIERS弯头尖嘴钳电话钳TELEPHONE PLIERS强力尖嘴钳TRIPLE-FUNCTION PLIERS直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳MECHANICS PLIER ANGLED PATTERN偏口机修工钳MECHANICS PLIER OFFSET PATTERN30度平圆机修钳MECHANICS PLIER WITH 30电缆刀CABLE KNIFE电工电缆刀ELECTRICIAN’S CABLE KNIFE防静电专用钳子电子钳ELECTRONIC PLIERS迷你电子钳MINIATURE ELECTRONIC PLIERS防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳电缆剪钳CABLE CUTTERS小型万用剪SMALL UNIVERSAL SCISSORS万用电缆刀UNIVERSAL CABLE KNIFE自动剥线钳STRIPPING PLIERS ANTOMATIC剥线钳STRIPPING PLIERS固定剥线钳STRIP-FIX STRIPPING PLIERS剥线工具WIRE STRIPPER高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳INSULATING VARNISH STRIPPER剥线刀WIRE STRIPPING KNIFE绝缘胶带INSULATING TAPE压线钳CRIMPING PLIERS锁把式压线钳LOCK-GRIP CRIMPING PLIERS端子压线钳WIRE END-SLEEVE PLIERS模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳MODULAR CRIMPING PLIERS精确压线钳PRECISION CRIMPING PLIERS外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头内卡簧钳（孔用）大型/重型卡簧钳X型把X-GRIP大力钳LOCK-GRIP PLIERS平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳WIDE JAW LOCKING PLIERS滑行杆式大力钳LOCK-GRIP SLIDE CLAMP固定大力钳GRIP WRENCH FOR GLUEING机械工作台钳MACHINE WORKBENCH CLAMP焊接大力钳LOCK-GRIP WELDING CLAMP管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMPC型大力钳LOCK-GRIP C CLAMP水泵钳UNIVERSAL PLIERS（7种设置/5种设置）水泵钳WATER PUMP PLIERS特殊水泵钳SPECIAL WATER PUMP PLIERS可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER 高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳MINI CHAIN PIPE WRENCH链钳CHANIN PIPE WRENCH重型管子钳STILLSON PIPE WRENCH断线钳BOLT CUTTERS钳子套装（3件/4件/6件/8件）VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLSVDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V DC1500V）VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角）VDE绝缘起子套装电压传感器/电压测试器VOLTAGE DETECTOR/TESTER绝缘扭力扳手VDE TORQUE WRENCH绝缘双向棘轮扳手VDE REVERSIBLE RATCHET绝缘六角套筒VDE SOCKET HEXAGONAL绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKETT型绝缘扳手VDE T-HANDLE绝缘延长杆VDE EXTENSION绝缘电工工具组套（3件/8件/14件/108件）VED 3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH 3C HANDLE绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET 绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNERVDE绝缘钢锯HACKSAW绝缘电缆刀VDE CABLE KNIFE绝缘电缆剪CABLE SHEARS棘轮式绝缘电缆剪钳CABLE CUTTERSVDE绝缘电缆剪VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳VDE绝缘橡胶垫VDE RUBBER COVER SHEETVDE绝缘电工安全手套VDE ELECTRICIANS’S SAFETY GLOVES绝缘塑料夹VDE PLASTIC CLAMPS车轮扳手WHEEL WRENCHES十字扳手4 WAY WHEEL WRENCH撬棒TYRE LEVER轮毂罩移除工具HUBCAP RENOVING TOOS配重钳BALANCE-WEINHT PLIERS制动弹簧钳BRAKE-SPRING PLIERS闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE 油壶OIL CANS过滤器扳手UNIVERSAL FILTER WRENCH皮带钳PULLEY WRENCH阀门研磨机VALVE GRUNDER阀门研磨工具VALVE LAPPING TOOS油封钳VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE 活塞环钳PISTON RING PLIERS软管夹钳HOSE CLIP PLIERS电极拉马BATTERY TERMINAL PULLER电池测试器BATTERY TESTER火花塞套筒SPARK PLUG SOCKET火花塞套筒扳手SPARK PLUG SOCKET WRENCH火花塞刷SPARK-PLUG BRUSH特殊尖冲凿SPECIAL PIN PUNCH弹簧撑开器SPRING SPREADER球头拉拔器UNIVERSAL BALL JOINT REMOVER通用罐UMIVERSAL CANISTER防冻测试器ANTI-FREEZE TESTER安装钳INSTALLATION PLIERS吸盘SUCTION LIFTER磁性拾取工具MAGNETIC PICK-UP TOOL金属片切割器NIBBER杠杆剪切机LEVER-ACTION TIN SNIPS打孔钳PUNCH PLIERS橡胶锤RUBBER HAMMER塑料锤PLASTIC HAMMER无后坐力锤RECOILLESS HAMMER钳工球头锤ENGINEERS’S BALL PEIN HAMMER钳工锤ENGINEERS’S HAMMER平面刮刀FLAT SCRAPER三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER密封刮刀GASKET SCRAPER平锉HAND FILE圆锉ROUND FILE三角锉TRIANGULAR FILE半圆锉HALF-ROUND FILE锉类6件套装中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW栓孔锯KEYHOLE SAW小金属锯SMALL METAL SAW小PUK钢锯PUK JUNIOR HACKSAWHOBBY锯台钳/台虎钳METALWORKING VICE（100/125/150mm）钢卷尺STEEL TAPE MEASURE（3米/5米/8米）阀塞尺VALVE FEELER GAUGE塞尺火花塞塞尺SPARK PLUG GAUGE螺纹规THREAD GAUGE游标卡尺POCKET VERNIER CALLIPER数显游标卡尺DIGITAL CALLIPER划线器SCRIBER镊子TWEEZERS十字镊子CROSSLOCK TWEEZERS螺钉取出器BOLT EXTRACTOR断螺钉取出器套装SCREW EXTRACTOR SET机械螺母破开器MECHANICAL NUT SPLITTER螺栓插入及取出器STUD INSERTER AND EXTRACTOR丝锥THREAD FILE管子割刀PIPE CUTTER自动切割机AUTOMATIC PIPE CUTTER链式切管机CHAIN PIPE CUTTER虹吸扳手SIPHON TRAP PLIERS钢丝刷WIRE BRUSH锉刀清洁刷FILE CLEANING BRUSH裁缝剪TAILORS SCISSORS发光二极管井下检查灯LED INSPECTION LAMP井下检查灯INSPECTION LAMP发光二极管工作灯LED WORK LIGHT工程锤ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤ENGINEERS’BALL PEIN HAMMER胡桃木备用手柄SPARE HANDLE HICKORY工匠锤JOINERS’HAMMER ROTBAND-PLUS石匠锤CLUB HAMMER双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS大锤SLEDGE HAMMER大碎石锤STONE SLEDGE HAMMER劈木锤WOOD SPLITTING HAMMER铺路锤PAVING HAMMER单板锤VENEER HAMMER磁性锤MAGNETIC HAMMER ROTBAND玻璃装配工锤GLAZIERS HAMMER炭化合金瓦锤CARBIDE TILE HAMMER羊角锤CLAW HAMMER电焊敲锤SCALING HAMMER ROTBAND-PLUS无弹力安全锤RECOILLESS HAMMER安全锤SAFETY HAMMER SOFT-PLUS塑料锤PLASTIC HAMMER橡皮锤RUBBER MALLET HARD尼龙锤NYLON HAMMER木锤WOOLEN MALLET铜锤COPPER HAMMER CLUB SHAPE铝锤ALUMINIUM HAMMER ROTBAND桶形铝锤LEAD HAMMER SARREL SHAPE冷凿锤COLD CHISEL HAMMER热凿锤HOT CHISEL HAMMER平底压摸锤SET HAMMER TOP PART压槽铁锤TOP FULLER上型模锤BOTTOM FULLER冲锤PUNCH HAMMER镰刀锤SCYTHE HAMMER锻工钳BLACKSMITH’S TONGS铆钉钳RIVETTING TONGS锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP 冲子组套DRIFT PUNCH SET铆钉装配器RIVET SETTER字母及数字冲子LETTER AND NUMBER PUNCHES装配冲子SETTING PUNCH撬杆PRVBAR起钉器NAIL FIFER OCTAGONAL撬棍CROWBAR通用拉马UNIVERSAL PULLER两爪拉马PULLER 2-ARM PATTERN三爪拉马PULLER 3-ARM PATTERN防腐蚀拉马COROSTOP PULLER PATTERN快速拉马QUICK-ACTION PULLER两爪液压拉马UNIVERSAL 2-ARM PULLER拉马延长杆EXTENSION FOR PULLERS液压轴杆HYDRAULIC PRESSURE SPINDLE三爪液压拉马UNIVERSAL 2-ARM PULLER拉马套装PULLER SET螺母劈开器NUT SPLITTER液压螺母劈开器NUT SPLITTER HYDRAULIC螺栓提取器STUD EXTRACTOR轴承提取器BALL BEARING EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTOR SET内提取器INTERNAL EXTRACTOR冲击轴承拉马IMPACT BEARING PULLER汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE 分离拉马SEPARATOR PULLER轴承分离器BEARING SEPARATOR传动轴轴承拉马DRIVE SHAFT BEARING PULLER分离器及拉马套装SEPARATOR AND PULLER SET拉拔卡盘PULLING CHUCK液压泵HYDRAULIC PUMP液压手泵HYDRAULIC HAND PUMP液压工具拉马1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器HYDRAULIC PRESS轮毂拉马WHEEL-HUB PULLER传动轴拉马DRIVE-SHAFT PULLER方向盘拉马STEERING-WHEEL PULLER装配叉DISMANTLING AND ASSEMBLY FORK球头拉拔器BALL JOINT PULLER三爪机滤扳手OIL FILTER HOOK弹簧撑SPRING SPREADER塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET 法兰分离器FLANGE SEPARATORS轨距测量器TRACK ALIGNMENT GAUGE扳手WRENCHES管子切割器PIPE CUTTERS扩口工具FLARING TOOLS弯管机PIPE BENDERS管子工具PLUMBING TOOLS铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS管子清洁设备PIPE CLEANING EQUIPMENT弯管系统PIPE BENDING SYSTEMSSNAP管道扳手PIPE WRENCH ECK-SNAP钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES管子修边器PIPE DEBURRING REAMER不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES 扩口工具套装FLARING TOOL SET BOERDEX钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机PIPE BENDER WITH ROLLER弯管钳PIPE BENDING PLIERS带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL 带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER手动弯管机MANUAL BENDING TOOL液压弯管机HYDRAULIC PIPE BENDER手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION 管道矫直工具PIPE STRAIGHTENING TOOL金属片弯边钳SHEET METAL CRINPING PLIERS折边钳SEAMING PLIERS快速夹取扳手QUICK-CLAMP WRENCH夹管钳GRIPPING PLIERS分级扳手STEPPED KEY复合分级扳手COMBINATION STEPPED KEY铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS 断线钳BOLT CUTTER管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT排水管清洁器DRAIN PIPE CLEANER工作台几工作桌WORKBENCHES AND WORK TABLES工具车TOOL TROLLEYS工具柜TOOL CABINETS车间推车WORKSHOP TROLLEYS抽屉柜/箱DRAWER-CABINETS/BOXES衣柜/工作服柜WARDROBES矮橱LOWER CUPBOARD UNIT图纸夹DRAWING HOLDER电源面板PWER SUPPLY PANEL防酸放腐蚀工作台面板六边形工作台HEXAGONAL WORKBENCH带抽屉工作台WORKBENCH WITH DRAWER CABINET塑料抽屉插件PLASTIC DRAWER INSERT工作桌推车WORKSHOP TABLE TROLIEYS工作台WORKBENCH带背板工作台坚固推车TROUGH TROLLEY平板车PLATFORM TROLLEY带手柄平板车PLATFORM TROLLYE WITH HANDLE维护推车SERVICE TROLLEY带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST工具箱TOOL CHEST存放斗STORAGE TRAY卷纸架PAPER ROLL HOLDER垃圾桶WASTE BASKET移动架写字板LECTERN WORKTOP存储盒STORAGE BOXES带门库架CUPBOARD WITH SHELVING WITH DOORS开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS 存物柜LOCKER WITH HINGED DOORS滑门橱CUPBOARD WITH SLIDING DOORS电脑柜COMPUTER CABINET桌上设备DESK INSTALLATION移动电脑架PC STAION MOBILE电脑车间组合PC WORKPLACE COMBINATION更衣室条凳CHANGING CUBICLE SEAT BENCH安全橱SAFETY CUPBOARD衣橱CLOTHES LOCKER带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH消防员衣橱FIREFIGHTER’S CUPBOARD工具橱TOOL CABINET移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY 分类垃圾收集站WASTE-COLLECTION STATION CONTAINER立式烟灰缸STAND ASHTRAYOCHSENKOPF系列斧头欧洲ILTIS型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS特殊工具KLANN汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扭距测试仪及设备TORQUE TESTER AND EQUIPMENT扭距倍增器TORQUE MULTIPLIERS扭距角度指示器TORQUE ANGLE INDICATORS特殊DREMO工具SPECIAL DREMO TOOLSDREMOMETER系列扭力工具DREMOMETER TOOLS扭距螺丝刀TORQUE SCREWDRIVERS扭距扳手/扭力扳手TORQUE WRENCHES电子扭距测试仪ELECTRONIC TORQUE TESTERDKD校准遵守DKD准则3-7/3-8/DIN EN ISO 6789RAHSOL DREMOTEC产品校准按照DIN EN ISO 6789标准迷你型扭距扳手DREMOMETER MINIDREMOMETER高强度铝合金扭距扳手含：DREMOMETER 1-12NM /10-100LBF.IN （塑料外表）DREMOMETER 6-30NM /50-270LBF.INDREMOMETER 8-40NM /70-350LBF.INDREMOMETER 20-120NM /15-90LBF.FTDREMOMETER 40-200NM /30-150LBF.FTDREMOMETER 50-300NM /35-220LBF.FTDREMOMETER 80-360NM /60-260LBF.FTDREMOMETER 110-550NM /80-405LBF.FTDREMOMETER 140-760NM /105-560LBF.FTDREMOMETER 520-1000NM /380-730LBF.FTDREMOMETER 750-2000NMDREMOMETER 1500-3000NMDREMOMETER系列棘轮头RATCHET HEADS DREMOMTER扭距限制接合器TORQUE LIMIT UNIT转角仪TORQUE ANGLE INDICATOR圆形插头式扭距扳手（覆盖范围8-1000NM）开口扳子头OPEN END RTTING梅花扳子头RING END RTTING半开口梅花扳子头FLARED END FITTING棘轮头RATCHET HEAD四方头FIXED SQUARE HEAD方形插头式扭距扳手（覆盖范围8-400NM）开口插头RECTANGULAR OPEN END RTTING梅花插头RECTANGULAR RING END RTTING半开口梅花插头RECTANGULAR FLARED END RTTINGTORCOFIX系列带四方驱动的扭距扳手TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K 含：4549-01 1-5NM 1/4’方头4549-02 2-25NM 1/4’方头4549-05 5-50NM 3/8’方头4550-10 10-100NM 1/2’方头4550-20 20-200NM 1/2’方头4550-30 60-300NM 1/2’方头4550-40 75-400NM 1/2’方头4550-55 100-550NM 3/4’方头4550-75 140-750NM 3/4’方头TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SETTORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K 蘑菇头MUSHROOM HEADTORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX ZTORCOFIX SE扭距扳手（四方插头）TORQUE WRENCH TORCOFIX SE TORCOFIX FS扭距扳手（可预设扭力值2-200NM）TORQUE WRENCH TORCOFIX FSTORCOFIX UK扭距扳手TORCOFIX UK TORQUE WRENCHTORCOFIX K扭距扳手TORCOFIX K TORQUE WRENCH扭距螺丝刀/扭力螺丝起子TORQUE SCREWDRIVERSFS型扭距螺丝刀范围0.02-13.6NMS型扭距螺丝刀范围0.05-9NMSP型扭距螺丝刀范围10-500CNMTSN预置扭距滑转扳手TSN SLIPPER QORQUE WRENCH 范围3-125NM TBN折弯式扭距扳手TBN BREAKER QORQUE WRENCH 范围0.2-135NM TSP预置扭距滑转扳手TSP SLIPPER QORQUE WRENCH 范围1-10NM TSC预置扭距滑转扳手TSC SLIPPER QORQUE WRENCH 范围1-10NM 电线标示系统PLASTIC-TAG MARKING SYSTEM刻度盘/表盘扭距扳手DIAL MEASUREMENT TORQUE WRENCHES适用场合：测试控制维护工作应用环境ADS 4 0.8-4NM 1/4’方头ADS 12D 2.4-12NM 1/4’方头ADS 25 5-25NM 3/8’方头ADS 40 8-40NM 3/8’方头BDS 80E 16-80NM 1/2’方头BDS 200 40-200NM 1/2’方头CDS 400S 80-400NM 3/4’方头DDS 800S 160-800NM 3/4’方头EDS 1400S 280-1400NM 1’方头EDS 2000S 400-2000NM 1’方头88型折弯式扭距扳手TYPE 88 BREAKER TORQUE WRENCH 范围100-1500NM8800-01 3/4’方头100-500NM8800-02 3/4’方头150-700NM8800-03 3/4’方头300-1000NM8800-04 3/4’方头700-1500NM8800-06 圆形插头16mm 130-550NM扭距倍增器/扭力放大器/齿轮减速器TORQUE MULTIPLIERS在狭小的空间内获得巨大的扭距输出型号不同范围含1000NM - 47500NM比例有1：5 1：15 1：15.5 1：25 1：26 1：75 1：125等等数字扭距扳手/数显扭力扳手ELECTRONIC TORQUE WRENCHE-TORC微处理器控制扭距扳手E-TORC ELECTRONIC TORQUE WRENCHTORCOTRONIC数显扭距扳手TORCOTRONIC ELECTRONIC TORQUE WRENCH 电子扭距测试仪ELECTRONIC TORSIONS TORQUE TESTER E-TP智能型电子扭距测试仪系列E-TP ELECTRONIC TORSIONS TORQUE TESTER范围包括：0.5-1000NM的测试扭距扳手测试架TORQUE WRENCH TEST FRAMEE-TP打印机E-TP PRINTERE-TP固定架E-TP ADAPTER PLATEE-TP转接器E-TP ADAPTORE-TP软件及数据线E-TP SOFTWARE INCL AND PC-CONNECTION CABLE E-TP包装箱E-TP PLASTIC-CASE。

飞机维修中各类工具中英文对照扳手Wrenches/套筒Sockets开口扳手Open End Wrenches梅花扳手Spline End Wrenches块扳手Crowfoot Wrenches开口/梅花扳手Combination Wrenches内六角扳手Hex Wrenches平板棘轮扳手Slab Ratchet棘轮扳手Ratchet Wrenches力矩扳手Torque Wrenches管钳Pipe Wrenches活动扳手Adjustable Wrenches六角套筒Six Point Sockets梅花套筒Twelve Point Sockets万向套筒Universal Sockets转接头Adaptor套筒接杆Socket Extension万向转接头Universal Joint螺刀Screwdrivers快速螺刀Fast Screwdrivers仪表螺刀Electronic miniature Screwdrivers 十字头螺刀PILLIPS Screwdrivers磁性螺刀Magnetic Screwdrivers一字头螺刀Flat Tip Screwdrivers摇把Speeders钳Pliers尖嘴钳Needle Nose Pliers大力钳Locking Pliers保险丝钳Safety Wire Twisters鹰嘴钳Adjustable Joint Pliers插头钳Connector Plug剥线钳Wire Strippers鱼口钳Combination Slip-Joint Pliers卡环钳Convertible Snap Ring Pliers剪线钳Diagonal Cutters压线钳Wire Crimpers电气工具Electronic Tools矿灯Safety Lamb (Miner’s Lamb)手电Flashing Light对讲机Interphone电烙铁Electronic Iron耳机Earphone防静电手腕Static Wrist电池Battery充电器Charger扬声器Speaker电源插座Receptacle电枪Electronic Runner电钻Electronic Drills指挥棒Flashing Emergency Light超声波Ultrasonic测量工具Measuring Tools钢板尺Steel Rulers卷尺Tape Rulers螺旋卡尺Outside Micrometer塞尺Feeler (Thickness) Gauges量杯Measuring Cup游标卡尺Dial Caliper表Gauges三用表Multi Meter兆欧表Meg Ohm Meter杂项Diversiform反光镜Inspection Mirror放大镜Magnifier软杆双爪式机械手Flexible Two_claw Pick Up Tool 软杆磁棒Flexible Magnetic Pick Up Tool 划刀Utility Knife刮刀Scraper Knife剪刀Snip (Scissor)锯Saw凿子Chisels錾子Punch三脚架Tripod (Spider)铜榔头Copper Hammer铁榔头Iron Hammer胶榔头Rubber Hammer弯勾Hook锉File镊子Nipper (Pliers)销钉插拔工具Pin Removal Tools气枪Pneumatic Runner气钻Pneumatic Drills铆钉枪Rivet Gun注射器Injector (Squirt)滑油加油车Oil Cart液压油加油车Hydraulic Fluid Cart注油枪Grease Gun抹布Dishcloth手套Glove绳索Rope工具箱Tools Kit工具架Tools Rack千斤顶Jack撬棒Tommy Bar工作梯Work Ladder砂轮Grinding wheel砂纸Sand paper胶带Adhesive Tape焊锡Soldering Tin拖把Tow Bar发光背心Flashing Vest护目镜Goggle (Blinkers)安全带Life Belt(Safety Belt)增补两用扳手CONBINATION SPANNER两用扳手套装COMBINATION SPANNER SET加长型两用扳手COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET 梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET两用棘轮扳手COMBINATION RATCHET SPANNER两用棘轮扳手套装COMBINATION RATCHET SPANNER SET1/4'连接物ADAPTOR 1/4'组合支架工具COMBINATION HOLDING TOOL小型发光二极管MINIATURE LED LAMP活动扳手SINGLE OPEN ENDED SPANNER扳手套装MAGNETO SPANNER SET单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER双开口扳手DOUBLE OPEN ENDED SPANNER双开口扳手套装DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手PLARE NUT SPANNER（OPEN）半月型梅花扳手HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN 开口敲击扳手OPEN ENDED SLOGGING SPANNER梅花敲击扳手RING SLOGGING SPANNER高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）延长管EXTENSION TUBE爪型扳手CROWFOOT SPANNER两用活头扳手COMBINATION SWIVEL HEAD WRENCH活结T型扳手SWIVEL HANDLE WITH SLIDING T套筒扳手SOCKET WRENCH弯头套筒扳手ANGLED SOCKET WRENCH双头套筒扳手DOUBLE ENDED SOCKET WRENCH旋棒TOMMY BAR分节旋棒STEPPED TOMMY BAR3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLET型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET 钩头扳手HOCK SPANNER WITH LUG带销扳手PIN SPANNER可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE1/4'标准六角套筒HEXAGON SOCKET1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET棘轮扳手RATCHETS套筒SOCKETS套筒套装SOCKETS SETS摩擦棘轮扳手FRICTION RATCHETS冲击工具IMPACT TOOLS旋具头BITS扭矩扳手TORQUE WRENCHES1/4梅花套筒SOCKET UD PROFILE1/4六角套筒星型套筒SOCKET FOR PROTRUDING HEAD SCREWS1/4一字，十字，星型，内六角旋具套筒1/4’双向棘轮套筒扳手1/4’REVERSIBLE RATCHETT柄棘轮扳手RATCHET WITH T-HANDLE手用棘轮头HAND RATCHET WITHOUT HANDLE1/4转3/8转换接头CONVERTER 1/4 TO 3/8T型滑动头手柄TOMMY BAR WITH SLIDING T活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT EXTENSION1/4四方驱动连接头SQUARE-DRIVE COUPLER1/4万向接头UNIVERSAL JOINT活动头手柄SWIVEL HANDLE套筒固定夹SOCKET RAIL WITH MAGNETIC3/8一字，十字，星型，内六角旋具套筒3/8六角套筒SOCKET HEXAGON 3/83/8梅花套筒SOCKET UD PROFILE塑料棘轮扳手PLASTIC RATCHET旋具头接头BIT ADAPTOR旋具头棘轮扳手BIT RATCHET旋具头螺丝起子BIT SCREWDRIVER旋具头延长杆BIT EXTENSION旋具头SCREWDRIVER BITS风动套筒IMPACT SOCKET风动套筒附件ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING 安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH3C米字螺丝起子3C星型螺丝起子3C球头六角螺丝起子5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS电工螺丝旗子ELECTRONIC SCREWDRIVER木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器MAGNETIZER AND DEMAGNETIZER方刃锥子SQUARE BLADED AWLT型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLET型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE内六角扳手HEXAGON SOCKET KEY加长内六角扳手EXTRA LONG HEXAGON SOCKET KEY加长球头内六角扳手内六角扳手套装HEXAGON SOCKET KEY SETT型星形螺丝起子SCREWDRIVER WITH T-HANDLE曲柄螺丝起子CRANKED SCREWDRIVER量规GARGE车灯测电笔CAR LIGHT TESTER6-24伏测电笔VOLTAGE TESTER 6-24V150-250伏测电笔VOLTAGE TESTER 150-250V钳子3件套装PLIERS SET，3-PIECE万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE 小钢丝钳SMALL COMBINATION PLIERS钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）强力钢丝钳POWER COMBINATION PLIERS塑料水口钳SIDE CUTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）电工剪钳ELECTRICIAN’S SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）杠杆剪钳LEVER-ACTION SIDE CUTTERS杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS核头钳TOWER PINCERS拨钉钳PINCERS平头钳FLAT NOSE PLIERS圆头钳ROUND NOSE PLIERS直头尖嘴钳LONG NOSE PLIERS弯头尖嘴钳电话钳TELEPHONE PLIERS强力尖嘴钳TRIPLE-FUNCTION PLIERS直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳MECHANICS PLIER ANGLED PATTERN偏口机修工钳MECHANICS PLIER OFFSET PATTERN30度平圆机修钳MECHANICS PLIER WITH 30电缆刀CABLE KNIFE电工电缆刀ELECTRICIAN’S CABLE KNIFE防静电专用钳子电子钳ELECTRONIC PLIERS迷你电子钳MINIATURE ELECTRONIC PLIERS防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳电缆剪钳CABLE CUTTERS小型万用剪SMALL UNIVERSAL SCISSORS万用电缆刀UNIVERSAL CABLE KNIFE自动剥线钳STRIPPING PLIERS ANTOMATIC剥线钳STRIPPING PLIERS固定剥线钳STRIP-FIX STRIPPING PLIERS剥线工具WIRE STRIPPER高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳INSULATING VARNISH STRIPPER剥线刀WIRE STRIPPING KNIFE绝缘胶带INSULATING TAPE压线钳CRIMPING PLIERS锁把式压线钳LOCK-GRIP CRIMPING PLIERS端子压线钳WIRE END-SLEEVE PLIERS模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳MODULAR CRIMPING PLIERS精确压线钳PRECISION CRIMPING PLIERS外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头内卡簧钳（孔用）大型/重型卡簧钳X型把X-GRIP大力钳LOCK-GRIP PLIERS平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳WIDE JAW LOCKING PLIERS滑行杆式大力钳LOCK-GRIP SLIDE CLAMP固定大力钳GRIP WRENCH FOR GLUEING机械工作台钳MACHINE WORKBENCH CLAMP焊接大力钳LOCK-GRIP WELDING CLAMP管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMPC型大力钳LOCK-GRIP C CLAMP水泵钳UNIVERSAL PLIERS（7种设置/5种设置）水泵钳WATER PUMP PLIERS特殊水泵钳SPECIAL WATER PUMP PLIERS可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER 高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳MINI CHAIN PIPE WRENCH链钳CHANIN PIPE WRENCH重型管子钳STILLSON PIPE WRENCH断线钳BOLT CUTTERS钳子套装（3件/4件/6件/8件）VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLSVDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V DC1500V）VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角）VDE绝缘起子套装电压传感器/电压测试器VOLTAGE DETECTOR/TESTER绝缘扭力扳手VDE TORQUE WRENCH绝缘双向棘轮扳手VDE REVERSIBLE RATCHET绝缘六角套筒VDE SOCKET HEXAGONAL绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKETT型绝缘扳手VDE T-HANDLE绝缘延长杆VDE EXTENSION绝缘电工工具组套（3件/8件/14件/108件）VED 3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH 3C HANDLE绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET 绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNERVDE绝缘钢锯HACKSAW绝缘电缆刀VDE CABLE KNIFE绝缘电缆剪CABLE SHEARS棘轮式绝缘电缆剪钳CABLE CUTTERSVDE绝缘电缆剪VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳VDE绝缘橡胶垫VDE RUBBER COVER SHEETVDE绝缘电工安全手套VDE ELECTRICIANS’S SAFETY GLOVES绝缘塑料夹VDE PLASTIC CLAMPS车轮扳手WHEEL WRENCHES十字扳手4 WAY WHEEL WRENCH撬棒TYRE LEVER轮毂罩移除工具HUBCAP RENOVING TOOS配重钳BALANCE-WEINHT PLIERS制动弹簧钳BRAKE-SPRING PLIERS闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE 油壶OIL CANS过滤器扳手UNIVERSAL FILTER WRENCH皮带钳PULLEY WRENCH阀门研磨机VALVE GRUNDER阀门研磨工具VALVE LAPPING TOOS油封钳VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE 活塞环钳PISTON RING PLIERS软管夹钳HOSE CLIP PLIERS电极拉马BATTERY TERMINAL PULLER电池测试器BATTERY TESTER火花塞套筒SPARK PLUG SOCKET火花塞套筒扳手SPARK PLUG SOCKET WRENCH火花塞刷SPARK-PLUG BRUSH特殊尖冲凿SPECIAL PIN PUNCH弹簧撑开器SPRING SPREADER球头拉拔器UNIVERSAL BALL JOINT REMOVER通用罐UMIVERSAL CANISTER防冻测试器ANTI-FREEZE TESTER安装钳INSTALLATION PLIERS吸盘SUCTION LIFTER磁性拾取工具MAGNETIC PICK-UP TOOL金属片切割器NIBBER杠杆剪切机LEVER-ACTION TIN SNIPS打孔钳PUNCH PLIERS橡胶锤RUBBER HAMMER塑料锤PLASTIC HAMMER无后坐力锤RECOILLESS HAMMER钳工球头锤ENGINEERS’S BALL PEIN HAMMER钳工锤ENGINEERS’S HAMMER平面刮刀FLAT SCRAPER三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER密封刮刀GASKET SCRAPER平锉HAND FILE圆锉ROUND FILE三角锉TRIANGULAR FILE半圆锉HALF-ROUND FILE锉类6件套装中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW栓孔锯KEYHOLE SAW小金属锯SMALL METAL SAW小PUK钢锯PUK JUNIOR HACKSAWHOBBY锯台钳/台虎钳METALWORKING VICE（100/125/150mm）钢卷尺STEEL TAPE MEASURE（3米/5米/8米）阀塞尺VALVE FEELER GAUGE塞尺火花塞塞尺SPARK PLUG GAUGE螺纹规THREAD GAUGE游标卡尺POCKET VERNIER CALLIPER数显游标卡尺DIGITAL CALLIPER划线器SCRIBER镊子TWEEZERS十字镊子CROSSLOCK TWEEZERS螺钉取出器BOLT EXTRACTOR断螺钉取出器套装SCREW EXTRACTOR SET机械螺母破开器MECHANICAL NUT SPLITTER螺栓插入及取出器STUD INSERTER AND EXTRACTOR丝锥THREAD FILE管子割刀PIPE CUTTER自动切割机AUTOMATIC PIPE CUTTER链式切管机CHAIN PIPE CUTTER虹吸扳手SIPHON TRAP PLIERS钢丝刷WIRE BRUSH锉刀清洁刷FILE CLEANING BRUSH裁缝剪TAILORS SCISSORS发光二极管井下检查灯LED INSPECTION LAMP井下检查灯INSPECTION LAMP发光二极管工作灯LED WORK LIGHT工程锤ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤ENGINEERS’BALL PEIN HAMMER胡桃木备用手柄SPARE HANDLE HICKORY工匠锤JOINERS’HAMMER ROTBAND-PLUS石匠锤CLUB HAMMER双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS大锤SLEDGE HAMMER大碎石锤STONE SLEDGE HAMMER劈木锤WOOD SPLITTING HAMMER铺路锤PAVING HAMMER单板锤VENEER HAMMER磁性锤MAGNETIC HAMMER ROTBAND玻璃装配工锤GLAZIERS HAMMER炭化合金瓦锤CARBIDE TILE HAMMER羊角锤CLAW HAMMER电焊敲锤SCALING HAMMER ROTBAND-PLUS无弹力安全锤RECOILLESS HAMMER安全锤SAFETY HAMMER SOFT-PLUS塑料锤PLASTIC HAMMER橡皮锤RUBBER MALLET HARD尼龙锤NYLON HAMMER木锤WOOLEN MALLET铜锤COPPER HAMMER CLUB SHAPE铝锤ALUMINIUM HAMMER ROTBAND桶形铝锤LEAD HAMMER SARREL SHAPE冷凿锤COLD CHISEL HAMMER热凿锤HOT CHISEL HAMMER平底压摸锤SET HAMMER TOP PART压槽铁锤TOP FULLER上型模锤BOTTOM FULLER冲锤PUNCH HAMMER镰刀锤SCYTHE HAMMER锻工钳BLACKSMITH’S TONGS铆钉钳RIVETTING TONGS锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP 冲子组套DRIFT PUNCH SET铆钉装配器RIVET SETTER字母及数字冲子LETTER AND NUMBER PUNCHES装配冲子SETTING PUNCH撬杆PRVBAR起钉器NAIL FIFER OCTAGONAL撬棍CROWBAR通用拉马UNIVERSAL PULLER两爪拉马PULLER 2-ARM PATTERN三爪拉马PULLER 3-ARM PATTERN防腐蚀拉马COROSTOP PULLER PATTERN快速拉马QUICK-ACTION PULLER两爪液压拉马UNIVERSAL 2-ARM PULLER拉马延长杆EXTENSION FOR PULLERS液压轴杆HYDRAULIC PRESSURE SPINDLE三爪液压拉马UNIVERSAL 2-ARM PULLER拉马套装PULLER SET螺母劈开器NUT SPLITTER液压螺母劈开器NUT SPLITTER HYDRAULIC螺栓提取器STUD EXTRACTOR轴承提取器BALL BEARING EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTOR SET内提取器INTERNAL EXTRACTOR冲击轴承拉马IMPACT BEARING PULLER汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE 分离拉马SEPARATOR PULLER轴承分离器BEARING SEPARATOR传动轴轴承拉马DRIVE SHAFT BEARING PULLER分离器及拉马套装SEPARATOR AND PULLER SET拉拔卡盘PULLING CHUCK液压泵HYDRAULIC PUMP液压手泵HYDRAULIC HAND PUMP液压工具拉马1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器HYDRAULIC PRESS轮毂拉马WHEEL-HUB PULLER传动轴拉马DRIVE-SHAFT PULLER方向盘拉马STEERING-WHEEL PULLER装配叉DISMANTLING AND ASSEMBLY FORK球头拉拔器BALL JOINT PULLER三爪机滤扳手OIL FILTER HOOK弹簧撑SPRING SPREADER塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET 法兰分离器FLANGE SEPARATORS轨距测量器TRACK ALIGNMENT GAUGE扳手WRENCHES管子切割器PIPE CUTTERS扩口工具FLARING TOOLS弯管机PIPE BENDERS管子工具PLUMBING TOOLS铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS管子清洁设备PIPE CLEANING EQUIPMENT弯管系统PIPE BENDING SYSTEMSSNAP管道扳手PIPE WRENCH ECK-SNAP钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES管子修边器PIPE DEBURRING REAMER不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES 扩口工具套装FLARING TOOL SET BOERDEX钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机PIPE BENDER WITH ROLLER弯管钳PIPE BENDING PLIERS带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL 带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER手动弯管机MANUAL BENDING TOOL液压弯管机HYDRAULIC PIPE BENDER手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION 管道矫直工具PIPE STRAIGHTENING TOOL金属片弯边钳SHEET METAL CRINPING PLIERS折边钳SEAMING PLIERS快速夹取扳手QUICK-CLAMP WRENCH夹管钳GRIPPING PLIERS分级扳手STEPPED KEY复合分级扳手COMBINATION STEPPED KEY铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS 断线钳BOLT CUTTER管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT排水管清洁器DRAIN PIPE CLEANER工作台几工作桌WORKBENCHES AND WORK TABLES工具车TOOL TROLLEYS工具柜TOOL CABINETS车间推车WORKSHOP TROLLEYS抽屉柜/箱DRAWER-CABINETS/BOXES衣柜/工作服柜WARDROBES矮橱LOWER CUPBOARD UNIT图纸夹DRAWING HOLDER电源面板PWER SUPPLY PANEL防酸放腐蚀工作台面板六边形工作台HEXAGONAL WORKBENCH带抽屉工作台WORKBENCH WITH DRAWER CABINET塑料抽屉插件PLASTIC DRAWER INSERT工作桌推车WORKSHOP TABLE TROLIEYS工作台WORKBENCH带背板工作台坚固推车TROUGH TROLLEY平板车PLATFORM TROLLEY带手柄平板车PLATFORM TROLLYE WITH HANDLE维护推车SERVICE TROLLEY带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST工具箱TOOL CHEST存放斗STORAGE TRAY卷纸架PAPER ROLL HOLDER垃圾桶WASTE BASKET移动架写字板LECTERN WORKTOP存储盒STORAGE BOXES带门库架CUPBOARD WITH SHELVING WITH DOORS开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS 存物柜LOCKER WITH HINGED DOORS滑门橱CUPBOARD WITH SLIDING DOORS电脑柜COMPUTER CABINET桌上设备DESK INSTALLATION移动电脑架PC STAION MOBILE电脑车间组合PC WORKPLACE COMBINATION更衣室条凳CHANGING CUBICLE SEAT BENCH安全橱SAFETY CUPBOARD衣橱CLOTHES LOCKER带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH消防员衣橱FIREFIGHTER’S CUPBOARD工具橱TOOL CABINET移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY 分类垃圾收集站WASTE-COLLECTION STATION CONTAINER立式烟灰缸STAND ASHTRAYOCHSENKOPF系列斧头欧洲ILTIS型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS特殊工具KLANN汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扭距测试仪及设备TORQUE TESTER AND EQUIPMENT扭距倍增器TORQUE MULTIPLIERS扭距角度指示器TORQUE ANGLE INDICATORS特殊DREMO工具SPECIAL DREMO TOOLSDREMOMETER系列扭力工具DREMOMETER TOOLS扭距螺丝刀TORQUE SCREWDRIVERS扭距扳手/扭力扳手TORQUE WRENCHES电子扭距测试仪ELECTRONIC TORQUE TESTERDKD校准遵守DKD准则3-7/3-8/DIN EN ISO 6789RAHSOL DREMOTEC产品校准按照DIN EN ISO 6789标准迷你型扭距扳手DREMOMETER MINIDREMOMETER高强度铝合金扭距扳手含：DREMOMETER 1-12NM /10-100LBF.IN （塑料外表）DREMOMETER 6-30NM /50-270LBF.INDREMOMETER 8-40NM /70-350LBF.INDREMOMETER 20-120NM /15-90LBF.FTDREMOMETER 40-200NM /30-150LBF.FTDREMOMETER 50-300NM /35-220LBF.FTDREMOMETER 80-360NM /60-260LBF.FTDREMOMETER 110-550NM /80-405LBF.FTDREMOMETER 140-760NM /105-560LBF.FTDREMOMETER 520-1000NM /380-730LBF.FTDREMOMETER 750-2000NMDREMOMETER 1500-3000NMDREMOMETER系列棘轮头RATCHET HEADS DREMOMTER扭距限制接合器TORQUE LIMIT UNIT转角仪TORQUE ANGLE INDICATOR圆形插头式扭距扳手（覆盖范围8-1000NM）开口扳子头OPEN END RTTING梅花扳子头RING END RTTING半开口梅花扳子头FLARED END FITTING棘轮头RATCHET HEAD四方头FIXED SQUARE HEAD方形插头式扭距扳手（覆盖范围8-400NM）开口插头RECTANGULAR OPEN END RTTING梅花插头RECTANGULAR RING END RTTING半开口梅花插头RECTANGULAR FLARED END RTTINGTORCOFIX系列带四方驱动的扭距扳手TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K 含：4549-01 1-5NM 1/4’方头4549-02 2-25NM 1/4’方头4549-05 5-50NM 3/8’方头4550-10 10-100NM 1/2’方头4550-20 20-200NM 1/2’方头4550-30 60-300NM 1/2’方头4550-40 75-400NM 1/2’方头4550-55 100-550NM 3/4’方头4550-75 140-750NM 3/4’方头TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SETTORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K 蘑菇头MUSHROOM HEADTORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX ZTORCOFIX SE扭距扳手（四方插头）TORQUE WRENCH TORCOFIX SE TORCOFIX FS扭距扳手（可预设扭力值2-200NM）TORQUE WRENCH TORCOFIX FSTORCOFIX UK扭距扳手TORCOFIX UK TORQUE WRENCHTORCOFIX K扭距扳手TORCOFIX K TORQUE WRENCH扭距螺丝刀/扭力螺丝起子TORQUE SCREWDRIVERSFS型扭距螺丝刀范围0.02-13.6NMS型扭距螺丝刀范围0.05-9NMSP型扭距螺丝刀范围10-500CNMTSN预置扭距滑转扳手TSN SLIPPER QORQUE WRENCH 范围3-125NM TBN折弯式扭距扳手TBN BREAKER QORQUE WRENCH 范围0.2-135NM TSP预置扭距滑转扳手TSP SLIPPER QORQUE WRENCH 范围1-10NM TSC预置扭距滑转扳手TSC SLIPPER QORQUE WRENCH 范围1-10NM 电线标示系统PLASTIC-TAG MARKING SYSTEM刻度盘/表盘扭距扳手DIAL MEASUREMENT TORQUE WRENCHES适用场合：测试控制维护工作应用环境ADS 4 0.8-4NM 1/4’方头ADS 12D 2.4-12NM 1/4’方头ADS 25 5-25NM 3/8’方头ADS 40 8-40NM 3/8’方头BDS 80E 16-80NM 1/2’方头BDS 200 40-200NM 1/2’方头CDS 400S 80-400NM 3/4’方头DDS 800S 160-800NM 3/4’方头EDS 1400S 280-1400NM 1’方头EDS 2000S 400-2000NM 1’方头88型折弯式扭距扳手TYPE 88 BREAKER TORQUE WRENCH 范围100-1500NM8800-01 3/4’方头100-500NM8800-02 3/4’方头150-700NM8800-03 3/4’方头300-1000NM8800-04 3/4’方头700-1500NM8800-06 圆形插头16mm 130-550NM扭距倍增器/扭力放大器/齿轮减速器TORQUE MULTIPLIERS在狭小的空间内获得巨大的扭距输出型号不同范围含1000NM - 47500NM比例有1：5 1：15 1：15.5 1：25 1：26 1：75 1：125等等数字扭距扳手/数显扭力扳手ELECTRONIC TORQUE WRENCHE-TORC微处理器控制扭距扳手E-TORC ELECTRONIC TORQUE WRENCHTORCOTRONIC数显扭距扳手TORCOTRONIC ELECTRONIC TORQUE WRENCH 电子扭距测试仪ELECTRONIC TORSIONS TORQUE TESTER E-TP智能型电子扭距测试仪系列E-TP ELECTRONIC TORSIONS TORQUE TESTER范围包括：0.5-1000NM的测试扭距扳手测试架TORQUE WRENCH TEST FRAMEE-TP打印机E-TP PRINTERE-TP固定架E-TP ADAPTER PLATEE-TP转接器E-TP ADAPTORE-TP软件及数据线E-TP SOFTWARE INCL AND PC-CONNECTION CABLE E-TP包装箱E-TP PLASTIC-CASE。

航空公司所需的飞行器维修工具
简介
本文档旨在介绍航空公司所需的飞行器维修工具。

航空公司需要维修工具来确保飞行安全和飞机的正常运行。

本文将概述常见的飞行器维修工具及其用途。

常见的飞行器维修工具
1. 扳手
扳手是一种常用工具，用于紧固和松开螺丝和螺母。

在飞行器的维修中，扳手可以用于拆解和安装飞机的各种零部件。

2. 螺丝刀
螺丝刀有多种类型，包括Phillips头、平头、十字头等。

螺丝刀用于拧紧和松开螺丝。

在飞行器维修中，螺丝刀被广泛用于拆卸和安装飞机的螺丝连接。

3. 钳子
钳子是一种用于夹取和固定物体的工具。

在飞行器维修中，钳
子可被用来修理电线，夹持小零件以及其他需要固定和抓握的场合。

4. 测量工具
测量工具包括卷尺、角度规、深度计等。

这些工具用于测量飞
机部件的尺寸、角度、深度等参数，以确保飞机零部件符合规格要求。

5. 洗涤剂和擦拭布
洗涤剂和擦拭布用于清洁飞机表面，去除污垢和油渍。

在飞行
器维修中，保持飞机的清洁是非常重要的，因为污垢和油渍可能影
响飞机性能，并且会导致维修工作的不准确。

6. 其他维修工具
除了上述列举的工具外，还存在许多其他类型的飞行器维修工具，例如焊接设备、气动工具、测试设备等。

这些工具根据维修需
求的具体情况而定。

结论
航空公司所需的飞行器维修工具多种多样，并且根据不同的维修需求而有所差异。

以上列举的工具是常见的飞行器维修工具，使用它们可以确保飞行器的安全和正常运行。

航空维修工具使用说明书一、概述航空维修工具是在航空维修领域中常用的设备，它们具有关键的作用，为维修人员提供了必要的工作支持。

本使用说明书将详细介绍航空维修工具的使用方法和注意事项，以确保使用者能够正确、安全地操作。

二、工具清单在开始使用航空维修工具之前，请确保您具备以下清单中列出的工具：1. 扳手：用于拧紧螺丝和螺母的工具；2. 手动起子：用于拧紧和松开螺丝的工具；3. 电动螺丝刀：适用于大量螺丝的快速拧紧和松开；4. 钳子：用于夹紧、固定和剪断物体的工具；5. 锤子：用于敲击和打击物体的工具；6. 量具：如尺、卡尺等，用于测量长度和距离；7. 焊接工具：适用于航空金属部件的修复和连接；8. 涂抹工具：如刷子、喷枪等，用于涂抹涂料和防腐剂；9. 电池工具：适用于依赖电池电力的工具。

请确保工具的数量和种类符合您的维修需求，并及时维护和更新工具以确保其状态良好。

三、正确使用方法1. 熟悉工具：在使用航空维修工具之前，要确保您已经熟悉并理解每种工具的使用方法和特性。

阅读并遵守每种工具的使用手册和安全说明。

2. 安全操作：在使用航空维修工具时，务必保持专注并正确的姿势。

避免戴手套、长袖衣物或其他可能干扰操作的物品。

确保手与工具之间有足够的间隙，以避免意外伤害。

3. 注意维护：要经常检查和维护航空维修工具，包括清洁、润滑和更换磨损或损坏的部件。

定期检查电动工具的电线和插头是否完好，并确保其正常工作。

4. 按照正确顺序使用工具：在维修工作中，按照指定的顺序正确地使用航空维修工具。

遵循正确的拆卸和装配步骤，并根据需要选择合适的工具。

5. 确保工具适用性：在使用航空维修工具时，要确保其适用于要维修的航空部件。

不要尝试使用不适合的工具，以避免损坏或安全隐患。

6. 合理使用力度：在使用手动工具时，要确保施加的力度适中，以免损坏维修对象或工具自身。

在使用电动工具时，要调整适当的扭矩或功率，以避免过度施加力度。

7. 安全存放工具：在结束工作或暂时停止使用航空维修工具时，要将其存放在安全的地方，防止他人接触，避免触发意外。