YWZ制动器说明书

YWZ5电力液压块式制动器YWZ5-400/80YWZ5-400/80 电力液压制动器 YWZ5电力液压推杆制动器 YWZ5制动器 YWZ5液压制动器广泛用于起重、冶金、矿山、港口、码头、建筑等机械驱动装置的减速和停车制动。

其安装尺寸和制动力矩参数符合JB/T6046-2006标准。

匹配Ed系列推动器性能安全可靠、制动平稳、动作频率高、制动力矩可调。

主要摆动铰点设自润滑轴承，传动效率高、寿命长，在使用过程中始终保持两侧瓦块退距均等，避免因退距不均使一侧制动衬垫浮帖制动轮的现象。

制动弹簧布置在弹簧管内，并在一侧设有制动力矩标尺，调整方便，直观。

可通过增设附加装置实现某些附加功能：手动释放装置释放（开闸）或闭合（闭闸）限位开关，可实现制动器是否正常释放或闭合的信号显示或连锁保护。

采用带下降延时阀的推动器推动，可实现制动器的延时闭合。

使用条件和规程：环境温度: －25℃～＋45℃。

空气相对湿度：≤90%海拔高度：符合GB755-2000标准。

电源：三相交流50Hz·380V. (根据用户要求也生产用于要求可提供60Hz或不同电压的产品。

适应的工作制：连续（S1）和断续（S3-60%）工作制。

一、概述YWZ 、YWZ2、YWZ3、YWZ4、YWZ5等系列液压块式制动器主要用于起重、运输、冶金、矿山、港口、建筑机械驱动装置的机械制动，具有制动平稳，安全可靠、维修方便、耗电少、寿命长、无噪音等优点。

①WYZ 系列操作次数每小时可达720次。

符合JB/ZQ4388-86标准； ②WYZ2系列操作每小时可达1200次，符合JB/ZQ4388-86标准； ③YWZ3系列操作每小时可达720次，符合GB6333-86标准； ④YWZ4系列操作每小时可达1200次，符合JB/ZQ4388-86标准； ⑤YW Z5系列操作每小时可达1200次，符合GB6333-86标准；二、使用条件1、环境温度-20℃~+50%(低于推动器改为YH-10航空液压油)2、空气相对湿度不大于90%3、一般用于三相交流电源，50HZ，380V；4、海高度符合GB755-87标准；5、在无爆炸危险，且介质中无足以腐蚀金属和破坏绝缘的气体及放电尘埃中；6、YZW、YZW3使用YTI系列推动器，一般适用于垂直工作，倾斜度不超过±去15°三、产品型号及意义四、外形尺寸图五、YWZ5技术数据、外形尺寸表(毫米)BED-80/6隔爆型电力液压推动器BED-80/12隔爆型电力液压推动器品牌：虹发产地：河南价格：1000人民币/台规格：BED-80/6，BED-80/12简要说明:BED系列电力液压推动器主要用作YWZ4，YWZ5，YWZ8，YWZ9，YWZP系列电力液压块式制动器的操作元件，广泛适用于起重运输，冶金，矿山，港口，建筑等行业。

本文部分内容来自网络整理，本司不为其真实性负责，如有异议或侵权请及时联系，本司将立即删除！== 本文为word格式，下载后可方便编辑和修改！ ==ywz5,说明书篇一：皮带机使用说明书DTII型固定式带式输送机产品使用说明书1目录一、用途、特点、使用范围二、主要参数三、整机的典型布置四、部件概述4.1、输送带 4.2、驱动装置 4.3、滚筒 4.4、托辊 4.5、拉紧装置 4.6、机架4.7、头部漏斗 4.8、导料槽 4.9、清扫器 4.10、卸料器4.11、电气及安全保护装置五、安装、调试与试运转六、操作规程与维护、保养七、润滑八、胀套的调整九、随机携带文件附件1: 滚筒用胀套参数附件2: 滚柱逆止器用弹簧参数附件3: 滚筒用轴承型号21 12 4 4 4 6 7 111112121213131523242525252627一、用途、特点、使用范围1.1 DTⅡ型固定式输送机是通用型系列产品，是以棉帆布、尼龙、聚酯帆布及钢绳芯输送带作曳引构件的连续输送设备，可广泛用于煤炭、冶金、电力、矿山、港口、化工、轻工、石油及机械等行业，输送各种散状物料及成件物品。

带式输送机具有运量大、爬坡能力高、运营费用低、使用维护方便等特点，便于实现运输系统的自动化控制。

1.2 输送物料的松散密度为500～2500kg/m3。

输送块度见表1。

注：块度系指物料最大线性尺寸1.3 工作环境温度:一般为-25℃～+40℃，对于有特殊要求的工作场所，如高温、寒冷、防爆、阻燃、防腐蚀、耐酸碱、防水等条件，应采取相应的防护措施。

1.4 DTⅡ型固定式带式输送机均按部件系列进行设计。

选用时可根据工艺路线，按不同地形及工况进行选型设计、计算、组装成整机。

制造厂按总图或部件清单生产、供货。

设计者对整机性能参数负责，制造厂对部件的性能和质量负责。

1.5 输送机应尽量安装在通廊内。

在露天场合下，驱动站应加防护罩。

1.6 本系列产品能满足水平、提升、下运等条件。

Cubic Electrical Hydraulic Brake YWZ SeriesUsers’Manual(For adjustment and maintenance)brake Co. Ltd. of CityAddress:Tel:Fax:Post Code:Website:E-mail:1. Essentials:Cubic Electrical Hydraulic Brake Series YWZ are mainly used in machines of such uses as craning ,transportation ,metallurgy, mining,porting, constructionand so on. They all accord with the JB/ZQ4388-97 standard.2. Working condifions:2.1 Temperature:-25℃-- +45℃(to see more information in the technical manual of YT1 promoter)2.2 No fire-catching,explosive or corrosive gas in the surrounding erwiroment.Relative air dampness not exceeding 90%.2.3 Power voltage to see the dataplate on promoter.2.4 The working altitude should conform to the standard of GB755-2000.3.Structure and fundamental theories:The Brake consist of a brake frame and a matching YT1 electrical hydraulic promoter when power is on ,the promoter works.Its stem rises quickly and loose the brake by a lever arm .When power off, the promoter’s stem falls quickly because of the push of the return spring and closes the brake by the lever arm .Note: structure may be differentaccording to different type and size(pi cture 1) picture of the structure1.screw bolt screw nut2.frame for installing brake tile3.brake tile4.brake arm5. screw bolt6. screw nut7. screw nut8. screw nut9.pull rod 10. screw nut 11.promoter 12.base4.type and data ( I )5.installation and adjustment5.1 check before installation :● check on the brake to see whether damage or less of parts happened● check and clean oil stains or other dirt on the surface of brakewheel if any5.2 installation of the brake :Please refer to picture I and follon the instructions here :●vertical installation : loose screw nuts number 6.7.8.10 tam thescrew stem 9 take off the brake arm ,and put the brake coat on the brake wheel;●horizontal installation : when brake wheel has been fixed on othermachines , loose screw nuts 6.7.8 and 10 then turn screw stem number9 and add on screw stems 5 and 9 ,put the brake arm on the brakewheel from a side .●After brake has been fixed on the base ,loosely drive the screwbolt on ,turn pull-rod 9.The screw nut in the frame for installing brake tile 2 should be at a proper position to get brake tiles and brake wheel tightly together . If there is still gap between them , continue turning pull rod 9 . Only when the best distance is reached can we stop turning the pull rod 9 and screw the nut tight .●Oil the promoter referring to it’s installations :5.3 Adjustment of the brake :● Adjustment of the promoter when working :First release foyce of the spring to the rising height (H1) of the promoter’s push rod conform to the statistics in table (一). With the wear and tear of the brake liner , working distance gets bigger and bigger , and H1 gets smaller and smaller when the numerial value of H1 gets to the smallest according to table II , ve-adjustment is needed according to the method above , otherwise the brake will become useless .●The adjustment of lever arm :Loosen nut 6, hold the sauare end of the screw-stem 5, drive nut 7, making the spring length conforms to the reference data on the data plate . When all is done , make screw nuts 6 and 7 tight .●The adjustment of returning the distance of the brake scotch : when thebrake tile is opened , adjust bolt 1 , make both sides return the distance and keep unanimity , If this serial brake is equipped with the equal retreat device , by which both sides retreat automatically equal when the brake is turned on , necdn’t adjust .●The nut 2 of the regular brake scotch (see the fig) should be fixed inconformity with elasticity to make the brake scotch can be up to the location with making driving wheel .6. Inspection and trying out before the brake is operated :6.1 Checking before running : The brake should be checked in an all-roundway before running , check whether every adjustment is correct , whether the locknut of every part is locked , impeller wiring is correct .6.2 Test run : Through check , all after being normal , brake should be testedfor several times at host engine , apply the brake liner carry on certain brake- in , in order to make them run well .7. How to use and maintain it :7.1 Check the brake regularly .7.2 Keep in mind the following points when checking .●To see whether any wear and tear has happened to the joints .●Check all parts work normally and all nuts are tight .●Check the rising height (H1) is normal , referring to instruction 5-3 and table I .●Check the hydraulic oil is enough , the oil does n’t leak or seep out and the insulating material wire in good condition .●When bottle and mandrel are worn and torn to 5% or their ellipse exceeds0.5mm , they should be replaced with new ones .●Check the brake tile and wheel are tight together , friction surface is all good and no oil stain and dirt spot . When the thickness of the brake liner gets to minimum , it should be replaced with a new one .。

符合标准 Standards compliant:应用:YW 系列电力液压鼓式制动器，广泛应用于各种起重运输、港口装卸、冶金设备、矿山机械及工程机械中各种机构的减速和停车(维持)制动。

Application:YW Seires electro-hydraulic drum brakes can be extensively used for deceleration and stop/braking of various mechanisms in various belt conveying, port handling, hoisting, metallurgical,mining and building machinery.YW 、YWB 系列制动器连接尺寸和技术要求符合JB/T6406-2006标准，制动力矩参数符合DIN15435标准；YW 系列配套符合JB/T10603-2006标准的YTD 系列推动器；YWB 系列配套符合DIN15430标准的Ed 系列推动器；本系列适用于新设计、新主机配套选用。

The dimensions and technology requirements of YW,YWB series brakes comply with JB/T6406-2006 standard, braking torque parameters comply with DIN15435 standard;YW series brakes are equipped with YTD series thrusters which comply with JB/T10603-2006 standard.YWB series brakes are equipped with YTD series thrusters which comply with DIN15430 standard.This series brakes is mainly used for new design and new main machines.YW 、YWB 系列YWZ5、YWZE 系列YWZ6、Y WZF 系列YWZ5、YWZE 系列制动器连接尺寸和制动力矩参数符合GB6333-86标准，技术要求符合JB/T6406-2006标准；YWZ5系列配套符合JB/T10603-2006标准的YTD 系列推动器；YWZE 系列配套符合DIN15430标准的Ed 系列推动器。

Application:YWZA,YWZC series electro-hydraulic drum brakes can be extensively used for mechanism deceleration and stop/braking of various belt transport, port handling, hoisting, metallurgical and building machinery.■YWZA 系列制动器连接尺寸和制动力矩参数符合JB/ZQ4388-86标准，技术要求符合JB/T6406-2006标准；配套EB1系列推动器。

本系列适用于取代原YWZ 、JCZ 、YWZ 及TJ2等系列老产品。

■YWZC 系列制动器连接尺寸和制动力矩参数符合GB6333-86标准，技术要求符合JB/T6406-2006标准；配套EB 系列推动器。

本系列适用于取代原YWZ3和YWZ □等系列老产品。

Standards compliant:■The dimensions and braking torque parameters of YWZA series brakes comply with JB/ZQ4388-86 standard, technology requirements comply with JB/T6406-2006 standard; EB1 series thrusters are equipped. The series products are suitable to take place of old products as YWZ ,JCZ ,YWZ and TJ2 series.■The dimensions and braking torque parameters of YWZC series brakes comply with GB6333-86 standard, technology requirements comply with JB/T6406-2006 standard; EB series thrusters are equipped. The series products are suitable to take place of old products as YWZ3 and YWZ □ series.YWZA.YWZC 系列电力液压块式制动器YWZA.YWZC Series Electro-hydraulic Drum BrakesYWZA 系列 SeriesYWZC 系列Series ■制动衬垫为卡装式整体成型结构，更换十分方便、快捷，备有半金属(无石棉)硬质和半硬质，软质(含石棉、无石棉)等不同材质的制动衬垫供用户选择。

电力液压制动器YWZ-300/45正常工作条件环境温度-20℃～40℃；完全相对湿度不大于90%；在无爆炸危险的介质中，且介质中无足以腐蚀和破坏绝缘的气体和导电尘埃的环境中；安装地点的海拔高度符合GB755-87标准，适用于三相380V，50Hz交流电源。

电力液压制动器YWZ-300/45主要技术参数型号匹配推动器制动力矩N.M 退矩 b C D d F G1 G2 H h1 i K MYWZ-100/18 MYT1-18ZB/2 40 0.6 70 137 100 13 75 125 125 384 100 40 110 138 YWZ-150/25 MYT1-25ZB/4 100 0.6 90 154 150 17 100 170 170 437 140 60 150 138 YWZ-200/25 MYT1-25ZB/4 200 0.7 90 154 200 17 100 195 195 440 170 60 175 156 YWZ-300/25 MYT1-25ZC/4 320 0.7 140 154 300 22 130 280 280 692 240 80 250 200 YWZ-300/45 MYT1-45Z/5 630 0.7 140 178 300 22 130 280 280 600 240 80 250 200 YWZ-400/45 MYT1-45Z/6 1000 0.8 180 178 400 22 180 360 360 735 320 130 325 265 YWZ-400/90 MYT1-90Z/8 1600 0.8 180 210 400 22 180 360 360 740 320 130 325 265 YWZ-400/125 MYT1-125Z/10 2200 0.8 180 254 400 22 180 360 360 850 320 130 325 271YWZ-500/125 MYT1-125Z/10 2650 0.8 200 210 500 22 200 415 415 885 400 150 380 310YWZ-600/90 MYT1-90Z/8 3200 0.8 240 210 600 26 220 505 520 1082 475 170 475 390YWZ-600/180 MYT1-180Z/12 5000 0.8 240 254 600 26 220 505 520 1082 475 170 475 390YWZ-700/180 MYT1-180Z/12 8000 0.8 280 254 700 34 270 580 600 1225 550 200 540 585YWZ-800/180 MYT1-180Z/12 10000 0.8 320 254 800 34 320 677 697 1417 600 240 620 510YWZ-800/230 MYT1-320Z/12 12500 0.8 320 375 800 34 320 677 697 1417 600 240 620 1100电力液压制动器YWZ-300/45用途YWZ系列电力液压块式制动器，采用MYT1系列推动器作为制动器的驱动装置。