三星K2200固件升级说明2

固件更新说明：Q23HWVersionV2.0首版固件VER：0.1.4，用户可在开机后选择进入设置—系统设置—产品信息查看本机固件版本号。

(本版固件仅适用于Q23HWVersionV2.0，此机型的机身底部丝印和说明书上均标注有HWVersionV2.0字样，请避免与机型Q23混淆。

)固件升级注意事项：-请用户认准固件再升级。

错刷固件将导致产品损坏，由此导致的问题只能由用户负责。

-升级前务必备份好机器内的重要数据，升级过程中很可能会格式化可移动盘，升级完成后原有的数据将全部丢失，无法恢复。

-升级前确认机器电量充足，最好是充满电再做升级，避免因为电量不足导致升级失败。

-升级过程中不能按复位键，升级过程中不能有升级要求以外的操作，以免因操作按键导致升级失败。

-没有问题的产品没必要升级固件，只有用户手上的播放器有固件更新说明中说明的问题时，固件升级才能解决问题。

-请避免升级操作不当导致升级失败，按升级方法操作，如有问题请联系经销商的售后部门协助升级。

升级方法一：1、将从蓝魔公司网站下载的Q23HWVersionV2.0最新固件压缩包解压缩到任意一个文件夹。

压缩包中应包含固件升级说明、Q23HWVersionV2.0软件Firmware.img、升级工具文件夹和DRIVER文件夹。

2、双击运行用户升级工具夹中的文件RKDeviceManage.exe3、点击固件信息后的按钮，在此处选择电脑中文件Q23HWVersionV2.0固件Firmware.img所在路径后，升级工具显示界面如下：4、把Q23HWVersionV2.0关机，插入USB线连接电脑。

（如果您是第一次升级本播放器，关机状态下，连接电脑后电脑系统会弹出驱动安装的请求，驱动程序在本压缩包的Driver文件夹内,根据电脑提示选择安装驱动。

）5、点击【升级】或【修复】，开始固件升级，用户可以在升级工具的相关窗口查看升级进度。

升级可能会擦除机内的所有数据，请注意升级前备份机内的重要文件。

SINAMICS S210 Firmware Update InstructionsYou have got the possibility to upgrade the converter to a new firmware version. You can also downgrade the converter to a previous firmware version, in order to deliver the machine with a constant firmware version.When upgrading the firmware the previous settings will be maintained.When downgrading to a previous firmware the converter is reset to factory defaults.Hardware PrerequisitesThis description is valid for the following article numbers:Main supply Power S210 article number as of Version Frame size1AC 230V100 W6SL3210-5HB10-1UF0V5.1FSA1AC 230V200 W6SL3210-5HB10-2UF0V5.1FSA1AC 230V400 W6SL3210-5HB10-4UF0V5.1FSB1AC 230V750 W6SL3210-5HB10-8UF0V5.1FSB3AC 400V400 W6SL3210-5HE10-4UF0V5.2FSA3AC 400V750 W6SL3210-5HE10-8UF0V5.2FSA3AC 400V 1 kW6SL3210-5HE11-0UF0V5.2FSA These1AC 230V converters support the SINAMICS Runtime firmware as of version V5.1.These3AC 400V FSA converters support the SINAMICS Runtime firmware as of version V5.2.Memory cards for the Firmware UpdateA SD-memory card is required for the firmware update.Either you can use a memory card which is already plugged into the converter or a new memory card. Alternatively you can order a memory card with software on which the desired firmware is already installed.Card type Article numberEmpty SD-Card6SL3054-4AG00-2AA0SD-Card with Firmware V5.16SL3054-4FB00-2BA0SD-Card with Firmware V5.1 SP1 6SL3054-4FB10-2BA0SD-Card with Firmware V5.1 SP16SL3054-4FB10-2BA0-Z F01with Extended Safety LicenseSD-Card with Firmware V5.26SL3054-4FC00-2BA0SD-Card with Firmware V5.26SL3054-4FC00-2BA0-Z F01with Extended Safety LicenseThese SD-Cards can also be used to store the licenses for functions which require licensing. (e. g. Extended Safety License). It is not possible to use standard SD-card for this purpose.NoteThe integrated card reader only supports SD-cards up to a memory capacity of 2 GB.SDHC- or SDXC-cards are not supported.Preparing the SD-card for the Firmware UpdateIn order to install the software on the SD-card a SD-card reader is required in the PC/PG.If you are using a SD-card with preinstalled firmware then you can directly proceed with the firmware update. Backup of the SD-cardIf you like to install software on a SD-card which is already plugged into the converter, then switch the converter off and eject the SD-card.Before installing new software on this SD-card it is absolutely necessary to save all directories/files of the SD-card on your PC/PG. This especially applies to the installed licenses (directory KEYS, if available). Preparing the SD-cardAfter backing up the SD-card content on the PC/PG you can delete all files from the memory card (if a directory KEYS exists it does not need to be deleted).Extract the ZIP-file with the firmware which you like to install onto the SD-card.Copy the directory KEYS from the backup on your PC/PG back onto the SD-card (in case the directory KEYS was available and has been deleted before).Firmware UpdateAttention:Please do not turn off the power supply of the converter during the update process and do not disconnect the motor (if it is connected)!Doing so could lead to faulty components.Please proceed as follows to perform a Firmware-Upgrade or –Downgrade:1. Switch the converter off.2. Insert the prepared SD-card into the converter and turn the converter on.3. The new firmware will be installed – this can take up to 5 minutes and more.The update has finished when both LEDs are blinking red synchronously every second.4. Switch the converter off and remove the memory card as needed.5. Switch the converter back on. The firmware of the connected DriveCliq-components will be updated.This requires and additional power off/on (RDY-LED is blinking fast in yellow; refer to alarmmessages in the webserver).6. Verify that the new firmware version was installed correctly. The firmware version is displayed on theHome page of the webserver below the converter symbol.7. Commission the converter if necessary.8. In case the memory card shall remain plugged into the converter, save the parameters in thewebserver so that the actual configuration is stored on the memory card as well.Extract LED-StatesPlease find further information concerning the LED states in the manual.Interesting Links:SINAMICS S210 Firmwarehttps:///cs/de/en/view/109744577SINAMICS S210 PROFINET GSDMLhttps:///cs/de/en/view/109752524。

HT-2200掌上电脑固化（升级）程序/文件方法为了完善HTOS操作系统和满足用户订制的需求，HT-2200提供了固化（升级）程序的功能。

HT-2200的升级是通过电缆和HT-2200与PC机之间的通讯程序，把升级文件从PC机上下载到HT-2200中。

1.升级HT-2200掌上电脑前的准备工作：1)需要一台HT-2200、一台PC机及HT-2200专用的通讯电缆。

2)PC机上预先安装用户盘USERDISK，以及生成新的HT.ROM文件。

（HT.ROM文件一般由本公司提供）3)进入HT-2200主控台的“系统设置”查看电池容量（只对充电电池适用），如果电压值等于或大于2.35v，表示可以升级；如果电压值低于2.35v，请先将电池充电或更换电池。

4)将HT-2200中的重要数据上装到PC机上。

5)将通讯电缆把PC机和HT-2200连上，记住通讯电缆与PC机连接的COM口。

2.操作步骤：1.确认准备工作做好后，关闭HT-2200。

2.按【5】+【↑】+【开关】键，HT-2200将显示出如下的画面：3.PC机进入MS—DOS控制台，进入erdisk\bin目录后，键入CP4PC后按回车，即可运行CP4PC程序。

4.进入HTROM.EXE所在目录后，键入HTROM后按回车，PC机显示屏出现如下界面：5.按PC机键盘的【C】键，选择与电缆连接的PC机COM口，【1】表示COM1，【2】表示COM 2。

COM口缺省设置为COM 1。

6.按PC机键盘的【U】键，在指定的位置输入“HT.ROM”，按【回车】键，再按【U】键，就开始升您的机器了，整个升级过程大约要3分多钟，升级完成后，PC机显示如图：7.如果需要对多台HT-2200升级，请改换另一台HT-2200，并进入升级状态。

按PC机键盘的【U】键，HT-2200即进入升级状态。

8.升级完成后，HT-2200显示如图：按HT-2200键盘的【空格】键退出升级状态，系统自动复位。

版权© 1995-2013 三星所有权保留。
4-1
4.故障排除
4.2 了解状态 LED 指示灯
状态 LED 的颜色表示打印机当前状态。
LED 状态
状态 关闭
绿色
红色
电 源 / 蓝色 唤醒
闪烁 照亮 闪烁
照亮
照亮 关闭
说明 •本机脱机。 •本机处于节电模式。 当背景灯闪烁时，本机正在接收或打印数据。 •本机联机并可以使用。 •出现小错误，并且机器正在等待清除错误。检查显示信 息。当清除问题时，机器继续运行。 •墨盒内所剩的墨粉不多了，估计墨盒接近使用期限，订
4-17
பைடு நூலகம்
4.故障排除
深度 1
深度 2 低碳粉量提示
大页面计数
4.5.3.技术模式菜单说明
深度3 碳粉 OPC 单元 总计 1 总计 2
深度4 [1-30]% [1-30]%
信息>报告 •配置 它显示了当前的打印机状态，软件版本，硬件版本，纸张设置等等。 •供应品信息 它显示了耗材的寿命状态和墨粉的使用状态。 •使用计数器 包含已打印的页面总数。 •故障信息 它显示了打印机体内可能发生的各种故障。同样也可以保存历史故障并记录故障次数。
从托盘2中拾取纸张(可选)
101-0050 0050-Registration
驱动定位辊。
101-0130 0130-T2 Feed Mot
T2进纸电机开/关。
101-0131 0131-T2 Feed Slow
T2进纸电机慢开/关。
102-0010 0010-Tray1 Empty
检测主BLDC电机是否以正常速度运转。
100-0120 0120-Exit Mot Fwd