PA全系列端子台规格书(中英文对照本)

一、美国美标管件标准美国标准ASME/ANSI B16.9 工厂制造的锻钢对焊管件ASME/ANSI B16.11 承插焊和螺纹锻造管件ASME/ANSI B16.28 钢制对焊小半径弯头和回头弯ASME B16.5 管法兰和法兰配件MSS SP-43 锻制不锈钢对焊管件MSS SP-83 承插焊和螺纹活接头MSS SP-97 承插焊、螺纹和对焊端的整体加强式管座二、垫片 Gasket (GSKT)垫片的型式 type of gasket平垫片 flat gasket环形平垫片 flat ring gasket平金属垫片 flat metal gasket夹棉织物的橡胶 elastomer with cotton fabric insertion夹石棉织物的橡胶 elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片 natural white rubber gasket压缩石棉垫片 compressed asbestos class gasket浸聚四氟乙烯的石棉垫片 PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环 inner ring外环，外定位环 outer ring波纹金属垫片 corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket双夹套垫片 double jacketed gasket金属包石棉平垫片 flat metal jacketed asbestos filled gasket整体金属齿形垫片 solid metal serrated gasket槽形金属垫片 grooved metal gasket环形连接金属垫片 ring joint metal gasket八角环形垫片 octagonal ring gasket椭圆环形垫片 oval ring gasket透镜式垫片 lens gasket非金属垫片 non-metallic gasket三、各种法兰管件中英文对照表法兰 Flange (FLG）整体管法兰 integral pipe flange钢管法兰 steel pipe flange螺纹法兰 threaded flange滑套法兰（包括平焊法兰） slip-on flange (SO); slip-on welding flange 承插焊法兰 socket welding flange松套法兰 lap joint flange (LJF)对焊法兰 welding neckflange (WNF)法兰盖 blind flange, blind孔板法兰 orifice flange异径法兰 reducing flange盘座式法兰 pad type flange松套带颈法兰 loose hubbed flange焊接板式法兰 welding plate flange对焊环 welding neck collar （及stub end相似）平焊环 welding-on collar突缘短节 stub end, lap翻边端 lapped pipe end松套板式法兰 loose plate flange压力级 pressure rating, pressure rating class压力—温度等级 pressure-temperature rating法兰密封面，法兰面 flange facing突面 raised face (RF)凸面 male face (MF)凹面 female face (FMF)榫面 tongue face槽面 groove face环连接面 ring joint face全平面；满平面 flat face; full face (FF)光滑突面 smooth raised face (SRF)法兰面加工 facing finish粗糙度 roughness光滑的 smooth齿形 serrated均方根 root mean square (RMS)算术平均粗糙高度 arithmetical average roughness height (AARH) 配对法兰 companion-flange螺栓圆 bolt circle (B.C.)四管道特殊件 Piping Specialty1.7.1 管道特殊件（组件）粗滤器 strainer过滤器 filter临时粗滤器（锥型） temporary strainer (cone type)y 型粗滤器 y-type strainerT型粗滤器 T-type strainer永久过滤器 permanent filter丝网粗滤器 gauze strainer洗眼器及淋浴器 eye washer and shower视镜 sight glass阻火器 flame arrester喷嘴；喷头 spray nozzle取样冷却器 sample cooler消声器 silencer膨胀节 expansion joint波纹膨胀节 bellow expansion joint单波 single bellow双波 double bellow多波 multiple bellow压力平衡式膨胀节 pressure balanced expansion带铰链膨胀节 hinged expansion joint轴向位移型膨胀节 axial movement type expansion joint自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节 tied expansion joint万向型膨胀节 universal type expansion joint球形补偿器 ball type expansion joint填函式补偿器 slip type (packed type) expansion joint单向滑动填料函补偿器 single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头 hose connection (HC)快速接头 quick coupling金属软管 metal hose橡胶管 rubber hose挠性管 flexible tube鞍形补强板 reinforcing saddles补强板 reinforcement pad特殊法兰 special flange漏斗 funnel排液环 drip ring排液漏斗 drain funnel插板 blank垫环 spacer8字盲板 spectacle blind; figure 8 blind 限流孔板 restriction orifice爆破片 rupture disk法兰盖贴面 protective disc费托立克接头 victaulic coupling1.8 端部连接 End Connection法兰端 flanged end坡口端 beveled end (BE)对焊端 butt welded end平端 plain end (PE)承插焊端 socket welding end螺纹端 threaded end (TE)承口 bell end焊接端 welding end法兰连接（接头） flanged joint对焊连接（接头） butt welded joint螺纹连接，管螺纹连接 threaded joint, pipe threaded joint 锥管螺纹密封焊连接 seal-welded taper pipe threaded joint 承插焊连接（接头） socket welded joint承插连接（接头） bell and spigot joint环垫接头 ring joint (RJ)万向接头 universal joint软钎焊连接（接头） soldered joint搭接接头，松套连接 lapped joint外侧厚度切斜角 bevel for outside thickncss内侧厚度切斜角 bevel for inside thickness内外侧厚度切斜角 bevel for combined thickness法兰式的 flanged (FLGD)对焊的 butt welded (BW)螺纹的 threaded (THD)承插焊的 socket welded (SW)小端为平的 small end plain (SEP)大端为平的 large end plain (LEP)两端平 both ends plain (BEP)小端带螺纹 small end thread (SET)大端带螺纹 large end thread (LET)两端带螺纹 both end thread (BET)一端带螺纹 one end thread (OET)支管连接 branch connection焊接支管 branch pipe welded directly to the run pipe 五、管件 Fitting弯头 elbow异径弯头 reducing elbow带支座弯头 base elbowk半径弯头 long radius elbow短半径弯头 short radius elbow长半径180°弯头 long radius return短半径180°弯头 short radius return带侧向口的弯头（右向或左向） side outlet elbow (right hand or left hand)双支管弯头（形） double branch elbow三通 tee异径三通 reducing tee等径三通 straight tee带侧向口的三通（右向或左向） side outlet tee (right hand or 1eft hand)异径三通（分支口为异径） reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run) 带支座三通 base tee异径三通（一个直通口及分支口为异径） reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式） reducing tee (reducing on both runs, bull head)45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run) 45°斜三通(一个直通口及支管为异径) 45° latera l (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通 cross等径四通 straight cross异径四通 reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet) 异径四通（一个直通口及分支口为异径） reducing cross (reducing on one run and outlet)异径四通（两个分支口为异径） reducing cross (reducing on both outlet) 异径四通（一个直通口及两个分支口为异径） reducing cross (reducing on one run and both outlet)异径管 reducer同心异径管 concentric reducer偏心异径管 eccentric reducer锻制异径管 reducing swage螺纹支管台 threadolet焊接支管台 weldolet承插支管台 sockolet弯头支管台 elbolet斜接支管台 latrolet镶入式支管嘴 sweepolet短管支管台 nipolet支管台，插入式支管台 boss管接头 coupling, full coupling半管接头 half coupling异径管接头 reducing coupling活接头 union内外螺纹缩接（俗称补芯） bushing管帽 cap (C)堵头 plug短节 nipple异径短节 reducing nipple; swage nipple1.3 弯管 Bend预制弯管 fabricated pipe bend跨越弯管（^ 形） cross-over bend偏置弯管（~ 形） offset bend90°弯管 quarter bend环形弯管 cirele bend单侧偏置90°弯管（? 形） single offset quarter bend S形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bend U形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend斜接弯管 mitre bend三节斜接弯管 3-piece mitre bend折皱弯管 corrugated bend 圆度 roundness。

插片端子规格书一、基本状况参照外观◆产品名称part name◆产品型号part number 环保信息◆Environmentalinformation◆互配型号Matching part二、主要性能指标： Main performance parameters■电气特征 Electrical characteristics序号 No 项目 Item 性能参数 Performance parameters1 额定电压 Rated Voltge 500V AC2 额定电流 Rated Currect 20A3接触电阻≤ 10mΩContact resistance4 耐电压 Dielectic Withstand≥ 2500V AC Voltage5绝缘电阻≥5000MΩInsulation resistance■机械特征 Mechanical Characteristic序号 No 项目 Item 性能参数 Performance parameters1 整体插入力 Total Mating,≤50 N Unmating Force2 连结器分别力 Total Unmating≥20N Force3 机械寿命 Durability times ≥200times4 适配线径 Wire AWG 24AWG ～22AWG，■环境特征 Environmental test1 工作温度 Temperature Range -40 ℃～ 85℃2 温升 Temperature Rise 50K3 IP 防备等级 IP protectionIP65 requirement4 盐雾试验 Salt Spray 48 hours湿热循环 Humidity- 25℃~65℃ ; 90%~95% RH; 10 次，部件无损害5 25℃~65℃ ; 90%~95% RH; 10 Cycles; No damageTemperature Cyclingto parts.6 温度寿命 Temperature life 温度 105℃下连续 250 小时 ; 部件无损害250hours at 105 ℃; No damage to parts.-55 ℃ (30 分钟 ), +85℃ (30 分钟 ); 重复 5次;7 温度冲击 Thermal Shock 部件无损害-55 ℃(30min.), +85 ℃ (30min.); 5 Cycles; No damage to parts高温 70 ℃，低温 -40 ℃，每个循环 16h，共进行9 个循环， 144h（6 天）8 温度循环 Temperature ; 部件无损害cycling High temperature 70℃，Low temperature -40 ℃，16h per cycle ， totally 9 cycles ，144h; Nodamage to parts.频次 :10-55-10Hz; 振幅 1.52mm; 每个垂直面持续 2 小时；电流瞬断时间小于 1us 10-55-109 机械振动 Vibration Hz Traversed in 1 minutes at 1.52mmamplitude 2 hours each of 3 mutually perpendicularplanes; Electrical discontinuity less than1us.加快度 490m/s2; 半正弦波；连续 11 毫秒；± X, ±Y, ±Z, 方向各 3 次; 电流瞬断时间小于 1us. Accelerate Velocity:490m/s 2;10 机械冲击 Mechanical Shock Waveform:Half-sine shock plus;Duration:11msec; 3drops each to normal andreversed directions of X,Y and Z axes;Electrical discontinuity less than 1us.三、主要部件的资料、工艺、表面办理信息：Main material information■塑料Plastic资料material 尼龙黑色PA66 black工艺Process 注射成型Injection molding阻燃等级Flammability rating UL94V-0■接触件 Contact Pin资料 material工艺 Process表面办理Surface treatment■壳体 Shell资料 material工艺 Process表面办理Surface treatment■密封件 Seals资料 material工艺 Process四、产品的简介、包装储藏运输方式：■产品简介： Introduction该产品为带绝缘公端子。

东莞市铄徕电子有限公司KINGLION ELECTRONICS CO.,LTD HTTP ：//WWW.KINGLIONGROUP .COMPA 系列 端子台平底型和凹槽型(底部加高1.2mm) 高脚型端子台(底部加高4.3mm)規格尺寸（Dimensions & Data尺 寸 Dimensions 型 号 Model 线 径 mm2 安 培 Amp 电 压 Volt.螺 丝 ScrewUnitA B C D E F 包 装 PackingPA7F PA7 FDS 1.5 1.5 17.5 17.5 450 450 M2.6×5 M2.6×5 (mm)(mm)96.2096.2017.0017.0014.5014.508.20 8.20 2.90 2.90 2.80 2.80 50pcs/bag 10bags/carton PA8F PA8 FDS 1.5 1.5 17.5 17.5 450 450 M2.6×5 M2.6×5 (mm)(mm)95.8095.8016.3016.3012.7012.708.00 8.00 2.90 2.90 2.80 2.80 50pcs/bag 10bags/carton PA8H PA8HDS 1.5 1.5 17.5 17.5 450 450 M2.6×5 M2.6×5 (mm)(mm)96.2096.2017.0017.0014.5014.508.00 8.00 2.90 2.90 2.80 2.80 50pcs/bag 10bags/carton PA8HT PA8HTDS 1.5 1.5 17.5 17.5 450 450 M2.6×5 M2.6×5 (mm)(mm)96.0096.0016.3016.3017.6017.608.00 8.00 2.90 2.90 2.80 2.80 50pcs/bag 10bags/carton PA9H PA9HDS 2.5 2.5 24.0 24.0 450 450 M3.0×6 M3.0×6 (mm)(mm)116.0116.020.2020.2016.7016.7010.0010.00 3.60 3.60 3.40 3.40 50pcs/bag 10bags/carton PA10F PA10 FDS 2.5 2.5 24.0 24.0 450 450 M3.0×6 M3.0×6 (mm)(mm)117.5117.520.2020.2015.8015.8010.0010.00 3.60 3.60 3.20 3.20 50pcs/bag 10bags/carton PA10H PA10HDS 2.5 2.5 24.0 24.0 450 450 M3.0×6 M3.0×6 (mm)(mm)117.5117.520.2020.2017.0017.0010.0010.00 3.60 3.60 3.20 3.20 50pcs/bag 10bags/carton PA10HT PA10HTDS 2.5 2.5 24.0 24.0 450 450 M3.0×6 M3.0×6 (mm)(mm)117.5117.520.2020.2020.1020.1010.0010.00 3.60 3.60 3.20 3.20 50pcs/bag 10bags/carton PA12H PA12HDS 6.0 6.0 41.0 41.0 500 500 M3.5×7 M3.5×7 (mm)(mm)140.7140.723.8023.8019.0019.0012.0012.00 3.90 3.90 4.20 4.20 50pcs/bag 8bags/carton PA14H PA14HDS 10.0 10.0 57.0 57.0 500 500 M4.0×9 M4.0×9 (mm)(mm)158.0158.025.6025.6025.2025.2013.5013.50 4.40 4.40 5.00 5.00 25pcs/bag 10bags/carton PA16H PA18H16.0 25.076.0 101.0500 500 M4.0×9 M5.0×11 (mm)(mm)169.8194.428.0036.9023.0028.7014.5016.504.20 4.206.007.5010pcs/bag 10bags/carton内容（Description):◆底部（base):F 为平底型(Fwith flat base)\H 型底部加高1.2mm(Hwith 1.2mm elevated base)\ HT 型底部加高4.3mm(HTwith 4.3mm elevated base)◆材质（housing material):高级尼龙66工程塑胶，防火等级UL 94V-2,94V-0(nylon66,natural)。

电机零配件中英文对照表PartChinese Description English Description REMARK No.图纸中文描述英文描述备注编号定子片STATOR LAMINATION转子片ROTOR LAMINATION定子FRAME-STATOR-COIL定子铁芯STATOR CORE定子铁芯STATOR-CORE INTERLOCKED定子铁芯STATOR CORE ASSEMBLY转子铁芯INTERLOCKED ROTOR CORE铸铝端盖END FRAME CAST铸铝端盖END-FRAME MACHINED压铸端盖END FRAME CASTING铁端盖END FRAME-STAMPING后盖END COVER端盖COVER BRACKET / BRKT CSTG OP/ENCL铸铝转子ROTOR CORE铸铝转子cast-aluminum rotor铸铝转子ROTOR-CORE (SPECIAL)铸铝转子ROTOR CORE CAST/MACH.轴SHAFT SHAFT(SINGLE FLAT)机壳MAIN FRAME槽楔SLOT-PEG / WEDGE槽绝缘纸SLOT-LINER /SLOT LINER槽绝缘INSULATION SLOT绝缘材料INSULATION MATERIAL保护器THERMOSTAT / PROTECTOR热保护器THERMOSTAT-ASSEMBLY热保护器与线THERMOSTAT-LEAD ASSEMBLY轴承 / 球轴承BEARING-BALL / BALL BEARING球形含油轴承BEARING SLEEVE含油轴承滑动轴承BEARING SLEEVE / SLEEVE BEARING48轴承压簧0048 SPRING BRG.LOADING48内固定盖0048 CAP RETAINER INSIDE48轴承压圈0048 SLINGER SLEEVE BRG挡圈RING RETAINING挡圈RETAING RING RET. RING 平垫圈WASHER PLAIN调整垫圈FELT WASHER橡胶垫圈PLASTIC WASHER轴承波形垫圈BEARING SPRING轴承调整垫圈BEARING SPACER波形弹簧垫圈WAVE SPRING弹簧垫圈WASHER SPRING甩水圈SLINGER WATER橡胶甩水圈SLINGER RUBBER尼龙防水圈SLINGER NYLON防尘盖DUST CAP防护盖(轴承) SHIELD (BEARING)喷漆防尘盖PAINTED DUST CAP减震圈DAMPING RING减振圈SPLIT RING护线圈GROMMET螺钉SCREW螺钉STUD铆钉RIVET螺钉THRUBOLT#8-32长螺钉THRUBOLT #8-32螺栓THRUBOLT 8-32 .164螺栓STUD螺母NUT HEX SS六角螺母NUT HEX #8-32六角螺母(加工螺纹) NUT-HEX自攻螺钉#10-32 NF SELF FORMING SCREW #10-32 NF 五金部件组件HARDWARE-GROUP端子片TERMINAL LUG端子TERMINAL FM KW KQ GQ MV PD AH FX GZ JD公接插件PLUG MALE-REVERSING母接插件PLUG FEMALE-REVERSING旗形母端子TERMINAL LEAD FLAG FEMALE1叉公端子TERMINAL MALE 1-PRONG母直端子STRAIGHT FEMALE连接片BONDING LUG接头SPLICE CONNECTOR连接器（接头）CONNECTOR(SPLICE) FK 电容CAPACITOR RUN电容CAPACITOR ROUND 370 VAC电容罩CAPACITOR HOUSING电容罩衬垫GASKET CAPACITOR HOUSING引线LEAD引线LEAD RED引出线图DWG-LEAD引线组 / 线束LEAD-GROUP / TERMINAL EK 引出线组件LEAD-TERMINAL-ASSEMBLY引出线组件LEAD GROUP ASSEMBLY引线端子组合LEAD STRIPPED引出线端子装配DWG LEAD AND TERMINAL ASY绑扎带TIE CABLE接地线GROUND-LEAD绝缘套管INSULATING SLEEVE套管SNAP BUSHING套管SLEEVE套管SLEEVE INS底座RIGID BASE插孔PLUG-HOLE尼龙调垫WASHER-THRUST NYLON轴承衬套TNSERT BALL BRG轴承垫片WASHER STEEL BEARING导向杯型垫圈WASHER CUPPED LEAD3叶波垫 3 LEGGED SPRING塑料袋PLASTIC BAG装订钉STAPLES风叶FAN塑料风叶PLASTIC FAN纸箱CARTON WITHOUT CAP.铭牌NAMEPLATE铭牌INS. LABLE PRINT不干胶标签STICKER-FIELD WIRING不干胶铭牌NAMEPLATE ADHESIVE铭牌和标签图DWG NAMEPLATE AND LABLE其他部件中英文对照表PartChinese Description English Description REMARK No.图纸中文描述英文描述备注编号盖子COVOR喷漆端盖ENDFRAME PAINTED端盖加工/金加工端盖END FRAME MACHINE /END FRAME MACHINED端盖装配 /端盖组件END FRAME ASSEMBLY /CANOPY ASSEMBLY车加工端盖0048 BRACKET MCHD OPEN/ENCL 17MM SB0048 BRACKET ASY OPEN/ENCL SB轴坯(C形轴) BODY(SHAFT-C)标准轴图SHAFT STDS. DWG轴装配SHAFT ASSEMBLY转子装配ROTATING-ASSEMBLY转子端盖装配ROTATING-END FRAME ASS.嵌线定子STATOR & COIL ASSEMBLY STATOR-COIL嵌线定子标准WOUND CORE STDS.定子装配/机壳嵌线定子组FRAME-STATOR-COIL ASSEMBLY件定子铁芯装配STATOR CORE ASSEMBLY定子铁芯自铆STATOR-CORE INTERLOCKED转子铁芯自铆ROTOR CORE INTERLOCKED机壳组装MAIN FRAME ASSEMBLY机壳展开图MAIN-FRAME BLANK机壳展开BLANK SHELL互锁转子铁芯ROTOR CORE INTERLOCKED互锁定子铁芯STATOR CORE INTERLOCK绝缘定子铁心INSULATED STATOR CORE电机组装图MOTOR ASSEMBLY电机装配图MOTOR ASSEMBLY SQUARE FLANGE 电机部装MOTOR SUB-ASSEMBLY装配图DRAWING GENERAL-ASSEMBLY电机外形图OUTLINE MOTOR外形图MOTOR OUTLINE SQUARE FLANGE 电气说明SPECIFICATION ELECTRICAL连接图CONNECTION DIAGRAM内部连接图DWG DIAG INT CONN内接线图CONNECTION-DIAGRAM INTRNL外接线图CONNECTION-DIAGRAM EXTRNL 外部连接图EXTERNAL PARTS & CONNECTIONS 空白铭牌BLANK NAMEPLATE单独包装的部件组合KIT PART-PACKED-SEPARATE纸箱标签LABEL CARTON警告标贴WARNING STICKER警告标签CAUTION LABEL电机鉴别号码WEBER GRAPHICS MOTOR IDENTIFICATION PART NUMBER开-关标签LABEL ON-OFF证书标签LABEL CERTIFICATION连接标签CONNECTION TAG接线片标签BONDING LUG STICKER标签LABEL BLANK BLUE / LABEL空白条形码STICKER BAR CODE BLANK保护器装配THERMOSTAT ASSEMBLY单个热保护器THERMOSTAT自动复位温度保护器THERMO AUTO RESET热保护器引线装配(2引线) THERMOSTAT&LEAD ASSEMBLY温度保护器组装2(7AM) THERMOSTAT ASSEMBLY 2(7AM)外部零件连接EXTERNAL-PARTS-CONNECTION压缩弹簧COMPRESSION SPRING电容夹CLAMP CAPACITOR支点盘PLATE PIVOT起动电容CAPACITOR START电容防护GUARD CAPACITOR保护器组件THERMOSTAT LEAD ASS.螺钉组件SCREW -EYELET ASS.带六角垫圈螺钉SCREW HEX WASHER螺钉螺母组合STUD-NUT ASSEMBLY#8-32 牙镀锌六角螺母HEX NUT #8-32 ZINC PLATED端子螺钉组件TERMINAL & SCREW ASS.端盖螺钉装配END FRAME STUD ASSEMBLY六角头头部带槽带锁紧垫SCREW HEX WASHER HEAD,THREAD FROM(GREEN) 螺钉(接地螺钉)六角头头部带槽带平垫螺SCREW HEX WSHR HD THREAD FORMING 钉开关触点CONTACT SWITCH开关臂BRACKET SWITCH ARM开关臂ARM SWITCH支撑SUPPORT CONTACT UPPER SGL支撑SUPPORT CONTACT开关装配SWITCH ASSEMBLY开关装配指导GOVERNOR ASSEMBLY INSTRUCTIONS开关绝缘板INSULATOR SWITCH离心开关装配GOVERNOR ASSEMBLY离心开关支撑GOVERNOR SUPPORT开关弹簧GOVERNOR SPRING插塞PLUG开关盘PLATE- SWITCH开关按钮BUTTON - SWITCH触点/刀片装配CONTACT& BLADE ASS.触点CONTACT开关刀片BLADE - SWITCH开关装配结构SWITCH ASS.INS.摇臂开关ROCKER ARMSWITCH货盘PALLET护盖PROTECTIVE CAP电镀挡板BAFFLE PLATED间隔SPACER PLASTIC管子TUBE轴承保持圈BEARING RETAINER 伸缩垫片EXPANSION WASHER 金属圈EYELET自调心滑动轴承固定垫圈0048 SELF ALIGNING SLEEVE BEARING CATCHER GASKET支撑衬垫SUPPORT PAD支撑衬垫组件KIT-SUPPORT PAD轴承衬套BEARING INSERT防松垫圈TYPE A INTERNAL TOOTH LOCKWASHER自锁垫圈LOCKWASHER抛油圈SLINGER锁紧垫圈LOCKWASHER BALL BRG塑壳CONNECTOR HOUSING接触圈RING CONTACT GOVERNOR刚性基座RIGID BASE内固定器件INTERNAL CATCHER端子板装配TERMINAL-BOARD ASS.浇注端子板MOLDED TERMINAL BOARD56轴承防尘盖0056 CAP BRACKET48盖装配0048 COVER ASY BKT48前盖垫片0048 GASKET COVER FRONT END外部零件连接图EXTERNAL PARTS AND CONNECTIONS 外部零件连接器EXTERNAL PARTS&CONNECTIONS56外齿锁紧垫圈0056 LOCKWASHER SHAKEPROOF EXTERNAL SERRATED无引线连接器CONNECTOR-LEADLESSFRAME-STATOR-COIL1.125保护(轴承) SHIELD(BEARING)绝缘件INSULATOR衬垫SPACER (CONDENSER)主体(轴-S) BODY(SHAFT-S)触点CONTACT锥形塞PLUG TAPERED可回收货盘0056RETURNABLE TRAY SQUARE FLANGE DESIGN 铭牌打印指导NAMEPLATE PRINTING INSTRUCTIONS标签打印指导LABEL PRINGTING INSTRUCTIONS隔垫标签STICKER-SPACER PAD泡沫衬垫FRONT END CAP轴套管SHAFT TUBEUL论证字符MONOGRAM DETAILCSA论证字符MONOGRAM DETAILPACK CARTON 75 PER/5 LYR泡沫聚苯乙烯STYROFOAM BLOCK外包装盖LID CORRUGATED EXPORT硬纸货盘说明PACK CARTON EXPORT凸缘管TUBE EXPORT出口衬垫EXPORT PAD打印说明PRINTING INSTRUCTIONS硬纸箱说明CARTON INSTRUCTIONS纸箱包装说明CARTON ASSEMBLY INSTR使用标贴STICKER SERVICE节能标贴STICKER CONSERVATIONIST内纸箱CARTON AOS INNER外纸箱CARTON AOS OUTER端部槽楔衬垫(单片) END WEDGE PAD 6"端部槽楔衬垫END WEDGE PAD 48 FR电机包装端帽MOTOR ENDCAP 48 FRAME出口货盘EXPORT PALLET出口货盘指导EXPORT PALLET INSTR引出线组件LEAD GROUP ASSEMBLY出口包装箱设置CELL SET-EXPORT出口隔离物EXPORT-PARTITION出口盘EXPORT TRAY外包装盘EXPORT TRAY盖子(出口) EXPORT LID型号功率电压电流频率转速Model Power Voltage Electric current Frequency Rotational speed 风叶直径风量Wind leaf diameter Amount of wind机电业常用英语电机（马达）electric motor,微电机micro motor小电机small motor分马力电机fractional horsepower motor直流电机Direct current motor, DC motor串励直流电机series wound DC motor并励直流电机shunt wound DC motor复励直流电机compound wound DC motor直流无刷电机Brushless direct current motor, BLDC motor空调暧通电机HV AC motor (heating, ventilating air-conditioning motor)交流电机Alternating current motor, AC motor串激电机universal motor齿轮电机Geared motor, Gear motor同步电机synchronous motor异步电机asynchronous motor, induction motor罩极电机shaded pole motor步进电机step motor, stepper motor, stepping motor 混合式hybrid磁阻式variable reluctance永磁式permanent magnet步距角精度step angle accuracy转轴shaft轴向负载axial load轴向窜动axial endplay径向跳动radial runout负载on load过载overload额定负载rated load空载no-load电流current电压voltage防护等级protection class, degree of protection, isolation class绝缘等级insulation class力距torque峰值peak value供应商supplier, vendor, seller客户customer, client, buyer样品（样机）prototype, sample试生产pilot production, try-out production 小批生产pre-series production批量生产series production打筋spline滚花knurl攻丝tap键槽keyway定位销stop pin螺钉screw螺纹thread螺栓bolt螺母nut联结器（接插件）connector端子：terminal标签, 铭牌label nameplate 起动力距starting torque最大(崩溃)转距break down torque 堵转locked rotor保持力距holding torque共振resonance电线（电缆）cable测试程序test procedure性能测试performance test耐压测试dielectric test (high pot test)功能测试functionality test, function test实地测试field test寿命测试life test老化试验ageing test连续运转continuous duty, continuous running间歇运转intermittent duty, intermittent running温升试验temperature rise test环境温度ambient temperature外形尺寸outside dimension outline精度accuracy公差tolerance不符合要求non-conformity, out of specification前端盖front flange, front end cover, front end bell, front end shield后端盖rear flange, rear end cover, rear end bell rear end shield凸台pilot齿轮，带轮pinion, gear wheel, gear滚珠轴承ball bearing含油轴承sleeve bearing, bronze bearing, self lubricating bearing转子rotor定子stator铁芯core电枢armature磁钢magnet整流子（换向器）commutator碳刷carbon brush, brush刷握brush holder喷砂sandblast涂胶gluing滴漆varnish电泳powder coating E-coating力矩速度曲线speed torque curve 机壳housing/shell轴承室bearing housing出轴shaft extension扁丝flat工装、夹具jigs, fixtures, tooling规gauge引出线lead wire, leads线路板PCB (printed circuit board) 驱动器driver, drive冲片lamination槽slot齿teeth轭yoke硅钢片silicon steel漆包线copper wire/enamel insulated copper wire胶带tape压铸die casting注塑mould injection波纹垫圈wave washer车加工machining 精车：turning霍尔传感器hall sensor开关switch装配assemble, assembly生产制造make, manufacture,磁通flux工艺流程图process flow chart 绝缘骨架plastic bobbin止口rabbet粗糙度roughness同心度concentricity偏心度eccentricity垂直度perpendicularity平行度parallelism produce动平衡balance. balancing 热处理heat treatment表面淬火case hardening穿透淬火through hardening 退火annealing正火temper表面涂覆surface coating有功：active power 无功：reactive power 电流：current容量：capacity 电压：voltage档位：tap position有功损耗：reactive loss无功损耗：active loss功率因数：power-factor功率：power 功角：power-angle电压等级：voltage grade空载损耗：no-load loss铁损：iron loss铜损：copper loss空载电流：no-load current阻抗：impedance正序阻抗：positive sequence impedance 负序阻抗：negative sequence impedance 零序阻抗：zero sequence impedance电阻：resistor电抗：reactance电导：conductance电纳：susceptance无功负载：reactive load 或者QLoad有功负载: active load PLoad遥测：YC(telemetering)遥信：YX励磁电流(转子电流)：magnetizing current定子：stator功角：power-angle上限:upper limit下限：lower limit并列的：apposable 高压: high voltage低压：low voltage中压：middle voltage电力系统 power system发电机 generator励磁 excitation励磁器 excitor电压 voltage电流 current母线 bus变压器 transformer升压变压器 step-up transformer高压侧 high side输电系统 power transmission system 输电线 transmission line固定串联电容补偿fixed series capacitor compensation 稳定 stability电压稳定 voltage stability功角稳定 angle stability暂态稳定 transient stability电厂 power plant能量输送 power transfer交流 AC装机容量 installed capacity 电网 power system落点 drop point开关站 switch station 双回同杆并架 double-circuit lines on the same tower 变电站 transformer substation补偿度 degree of compensation高抗 high voltage shunt reactor无功补偿 reactive power compensation 故障 fault调节 regulation裕度 magin三相故障 three phase fault故障切除时间 fault clearing time极限切除时间 critical clearing time 切机 generator triping高顶值 high limited value强行励磁 reinforced excitation线路补偿器 LDC(line drop compensation) 机端 generator terminal静态 static (state)动态 dynamic (state)单机无穷大系统 one machine - infinity bus system 机端电压控制 AVR电抗 reactance电阻 resistance 功角 power angle有功（功率） active power 无功（功率） reactive power 功率因数 power factor无功电流 reactive current下降特性 droop characteristics 斜率 slope额定 rating变比 ratio参考值 reference value电压互感器 PT分接头 tap下降率 droop rate仿真分析 simulation analysis 传递函数 transfer function框图 block diagram受端 receive-side裕度 margin同步 synchronization失去同步 loss of synchronization 阻尼 damping摇摆 swing保护断路器 circuit breaker电阻：resistance 电抗：reactance阻抗：impedance电导：conductance 电纳：susceptance 导纳：admittance 电感：inductance 电容: capacitance串激电机：universal motor转轴：shaft 换向器：commutator 铁芯：rotor steel core 端板：end spider 绝缘纸：rotor steel liner 槽楔（环）：wedge ring U型挡圈：U type retainer漆包线：field magnet wire 轴承：bearing 绝缘漆：varnish 换向片：commutator segment定子：铁芯：rotor steel core 漆包线：field magnet wire 绝缘纸：rotor steel liner支架：bracket支撑组件：机壳：housing 端盖：support frame碳刷组件：碳刷：brush 碳刷套：brush sleeve 碳刷架(刷握)：brush holder 弹簧：brush spring刷辫：brush flexible 刷盒：brush box风机部分：定叶轮：diffuser（guide vane）动叶轮：impeller 风罩：fan cover 螺钉：screw螺帽：nut-fan 压圈：gasket-fan 衬套：bush-fan爬电距离：creepage distances specify ：指定（动）附加绝缘：supplementary insulation clause ：条款（名）基本绝缘：basic insulation wear ：磨损（动）加强绝缘：reinforced insulation clearance ：电气间隙Clearance and creepage distances over supplementary and reinforced insulation not reduced below the values specified in clause 29 as a result of wear.accessible ：易接近的，可到达的，易受影响的loose ：宽松的，不牢固的Creepage distances and clearance between live parts and accessible parts not reduced below values specified for supplementary insulation if wires ,screws etc. becomes loose.Vaccum吸尘器Hose：软管Attachment ：附件，附加装置Transformer ：变压器From the result of our inspection and tests on the submitted samples, we conclude that that they comply with the requirements of the standards.Submit:提交，递交inspection : 检查comply with : 符合All models have same constructions, and are portable,dry-pick up vaccum cleaners for household use .Different models in one series with different postfixes are same products, but marked with different powers. Refer to below table for difference between models in different series.Postfix : 后缀refer to : 查阅提到谈到打听电动机：motor直流电动机：direct current motor交流电动机：alternating current motor交直流两用电动机：universal motor同步电动机：synchronous motor {siNkrEnEs]笼型同步电动机：cage synchronous motor同步感应电动机：synchronous induction motor磁阻电动机：reluctance motor亚同步磁阻电动机：subsynchronous reluctance motor异步电动机：asynchronous motor {eI`sINkrEnEs}感应电动机：induction motor无刷绕线转子感应电动机：brushless wound-rotor induction motor他励：separately excited自励：self-excited混励：compositely excited并励：shunt串励：series复励：compound excited复励：用以指明电机至少由两个绕组励磁，其中之一是串励绕组绕组：winding初级绕组：primary winding次级绕组：secondary winding主绕组：main winding定子绕组：stator winding转子绕组：rotor winding电枢绕组：armature winding阻尼绕组：damping winding起动绕组：starting winding辅助起动绕组：auxiliary starting winding励磁绕组：excitation winding磁场绕组：field winding试验：性能试验：performance test型式试验：type test重复试验：duplicated test检查试验：routing test 对每台电机在制造完工后所进行的试验，以判明其是否符合标准抽样试验：sampling test验收试验：acceptance test效率：efficiency 输出功率对输入功率之比总损耗：total loss(of a machine) ; power losses(of a machine ) 输入与输出功率之差热量试验：calorimetric test 从电机所产生的热量来推算损耗的试验方法空载试验：no-load test 在电机作电动机运行而轴上无有效机械输出时进行的试验轻载试验：light load test 当电机在驱动或被驱动状态下运行时，做为电动机，仅供给被驱动机械的空载损耗。

haso标准件中英文对照HASCO Z标准件系列Z00 导柱Guide pillarZ01 导柱Guide pillarZ011 导柱Guide pillarZ012 导柱Guide pillarZ013 导柱Guide pillarZ014 导柱Guide pillarZ0141 导柱连接端End p ieceZ0142 导柱连接端End p ieceZ015 导柱Guide pillarZ0151 导柱连接端（Z015/…专用）Pillar ada pter Z0152 导柱连接端Pillar ada pterZ02 顶杆Ejector rodZ022 导管Guide sleeveZ03 导柱Guide pillarZ05 圆锥形管精定位Locating unit, roundZ055 圆形垫片SpacerZ056 圆形垫件SpacerZ06 平锥形导块Locating unitZ07 长方形导块Square guide barZ08 直身方形管位导块Pre-centering unitZ081 方形垫片Sp acer discZ091 方形定位锁块（公）Square interlockZ092 方形定位锁块（母）Square interlockZ093 方形定位锁块（母）Square interlockZ10 导套Guide bushZ10W 自润滑导套Guide bushZ11 导套Guide bushZ11W 自润滑导套Guide bushZ12 滚珠导套Ball guide bushZ13W 自润滑导套Self lubric.Guide bush Z15W 自润滑垫片Self lubric. Flat stock Z16W 自润滑垫片Self lubric. Guide rail Z17 长方形导块（Z07/...专用）Guide retainerZ20 定板导套Centering sleeveZ25 定位销Dowel pinZ26 定位销Dowel pinZ28 六角螺母Hexagon nutZ281 六角螺母Hexagon nutZ282 六角螺母Hexagon nutZ285 螺母Nut for T-slotsZ286 螺母Nut for T-slotsZ30 胚头内六角螺丝Socket head cap screwZ31 胚头内六角螺丝Socket head cap screwZ32 薄胚头内六角螺丝Socket head cap screwZ33 薄胚头内六角螺丝Countersunk screwZ34 内六角螺丝Hexagon socket set screw Z35 内六角螺丝Hexagon socket set screw Z351 内六角螺丝Hexagon socket set screw Z352 螺丝杆Locking screwZ36 弹簧滚珠螺丝Sp ring pl ungerZ361 弹簧滚珠螺丝Sp ring pl ungerZ37 弹簧滚珠螺丝Sp ring pl ungerZ370 弹簧定位螺丝Sp ring pl ungerZ371 弹簧滚珠螺丝Sp ring pl ungerZ372 弹簧定位螺丝Sp ring pl ungerZ3721 弹簧定位螺丝Sp ring pl ungerZ373 弹簧定位镶件Sp ring pl ungerZ374 弹簧滚珠镶件Sp ring pl ungerZ375 弹簧滚珠镶件Sp ring pl ungerZ38 限位螺丝Shoulder screwZ381 螺丝Slotted shoulder screw Z39 螺丝Slotted shoulder screw Z40 顶针（全硬）Ejector pinZ41 顶针（表层硬）Ejector pinZ42 顶头顶针（全硬）Ejector pinZ43 顶头顶针（表层硬）Ejector pinZ44 有托顶针（表层硬）Shouldered ejector pin Z441 有托顶针（全硬）Shouldered ejector pin Z442/.../S 有托顶针（定制件）Ejector pinZ45 司筒（表层硬）Ejector sleeveZ451 司筒（全硬）Ejector sleeveZ4501 司筒（全硬）Ejector sleeveZ452/ -/S 司筒（定制件）Ejector sleeveZ453/ -/S 司筒（定制件）Ejector sleeveZ454/ …/S 司筒（定制件）Ejector sleeveZ455/ …/S 司筒（定制件）Ejector sleeveZ456 顶针耐磨镶件Wear sleeveZ456/…/S 顶针耐磨镶件（定制件）Wear sleeveZ46 扁顶针（表层硬）Flat ejector pinZ461 特殊扁顶针Sp ecial flat ejectorZ462 特殊扁顶针镶件（Z461/…专用）GuideZ465 扁顶针（全硬）Flat ejector pinZ466/ …/S 扁顶（定制件）Flat ejector pinZ47 顶针延长杆Extension rodZ48 年月标记镶件Date insertZ4800 标记镶件Marking insertZ4801 更新标记镶件Renew insertZ481 更新年份镶件Year insertZ482 月份标记镶件Month insertZ483 年份标记镶件Year insertZ484 箭头标记镶件Arrow insertZ485 年月标记镶件Date insertZ4851 更新年份镶件Year insertZ4861/1 塑料标记镶件Resin marking insert Z4861/2 班别标记镶件Shift marking insert Z4861/3 日期标记镶件Day marking insertZ4861/4 月份标记镶件Month-marking insert Z4861/5 年份标记镶件Year-marking insert Z4863 年月日标记镶件Multi. Marking insert Z4864 年月日塑料标记镶件Multi. Marking insert Z487/1 “回收标记”嵌件Recycling insertZ487/2 “回收标记”嵌件Recycling insertZ487/3 “回收标记”嵌件Recycling insertZ488 CE标记镶件CE marking insertZ489 食物标记镶件Food marking insert Z49 模芯镶件Core pin Z491 气动顶出阀Air valveZ492 模芯镶件Cpre pinZ495 喷气块Blow off stripZ4951 喷气咀Blow off nozzleZ50 唧咀Sprue bushingZ51 唧咀Sprue bushingZ511 唧咀Sprue bushingZ512 唧咀Sprue bushingZ515 气动唧咀Pneumatic nozzleZ516 细水口镶件Nozzle insertZ518 唧咀Sprue bushingZ519 唧咀Sprue bushingZ53 扣水口镶件Sprue p ullerZ55 顶针板园垫件Stop pinZ551 顶针板园垫件Stop pinZ56 环子Head for ejector rod Z561 环子Head for ejector rodZ562 介子WasherZ57 园形垫件Support p illarZ571 园形垫件Support p illarZ60 园线弹簧Comp ression sp ring Z601 园线弹簧Comp ression sp ring Z62 蝶形弹簧Disc sp ringZ64 方线弹簧Comp ression sp ringZ65 扁线弹簧Comp ression sp ring Z67 弹弓介子环Retaining ringZ671 弹弓介子钳Mounting p liersZ68 弹弓介子环Retaining ringZ681 弹弓介子钳Mounting p liersZ69 螺丝介子Sp ring washerZ691 螺丝介子Sp ring washerZ70 吊架连吊环Lifting deviceZ701 调距螺栓Distance boltZ71 吊环Eye boltZ711 吊环Eye boltZ712 吊环Eye boltZ72 吊环Eye boltZ73 安全扣T ool safety device Z741 固定玛夹Power clam pZ7411 空板架Sp acer blockZ7412 空板架Sp acer blockZ742 固定玛夹Power clam pZ743 固定玛夹Power clam pZ75 固定玛夹Clam p systemZ751 T头螺丝T head boltZ752 T头螺丝T head boltZ7521 T头螺丝T head boltZ7522 T头螺丝T head boltZ753 介子环Sp herical washerZ754 介子环Conical seat washer Z755 介子环Conical seat washer Z76 快速玛夹模装置Quick clam ping jig Z761 快速玛夹模板Clam ping p lateZ762 玛夹导柱Clam ping boltZ763 玛夹锁钉Eccentric boltZ765 离合锁（套）Locking housingZ766 离合锁（插）Locking plugZ80 带阀快接喉套Shut-off coup ling Z80/ …/45 带阀快接喉套Shut-off coup ling Z80/ …/90 带阀快接喉套Shut-off coup ling Z801 快接喉套Coup lingZ801/…/45 快接喉套Coup lingZ801/…/90 快接喉套Coup lingZ805 带阀侨式快接喉套Diverting coup ling Z8051 侨式快接喉套Diverting coup ling Z807 带阀快接喉套Shut-off coup ling Z807/ …/45 带阀快接喉套Shut-off coup ling Z807/ …/90 带阀快接喉套Shut-off coup lingZ808 快接喉套Coup lingZ809 带阀快接喉套Multi. shut-off couplingZ81 快接喉咀Nipp leZ81/ …/90 喉嘴Nipp leZ811 带阀快接喉咀Shut-off ni ppleZ812 适配连接头Double sided connector Z814 适配连接头Ada pterZ815 适配连接头Ada pterZ817 喉咀Hose nippleZ819 带阀快接喉咀Multi. shut-off ni pp le Z82 带阀快接喉套Shut-off coup lingZ83 喉咀Hose connectorZ831 快接喉套Plug-in connectorZ84 PVC喉管PVC-HoseZ85 PVC喉管PVC-HoseZ851 PVC喉管PVC-HoseZ853 耐高温喉管Viton-HoseZ854 耐高温喉管T eflon-HoseZ855 耐高温喉管Corrugated metal hoseZ86 喉箍Hose cli pZ861 紧夹用喉箍Crim ping sleeveZ865 紧夹用喉钳Crim ping toolZ87 喉咀Hose nippleZ875 喉咀Hose nippleZ876 喉咀Hose nippleZ876/ …/45 喉咀Hose nippleZ876/ …/90 喉咀Hose nippleZ877 连接头Joining p ieceZ878 转曲连接头ConnectorZ88 喉咀Hose nippleZ89 喉咀Hose nippleZ90 加长快接喉咀Extension nippleZ905 适配连接头Ada pterZ906 延长管Extension tubeZ91 加长喉咀Extension tubeZ93 密封胶布Sealing tape (Teflon)Z94 喉塞Tap ered plugZ941 喉塞Tap ered plugZ942 膨胀喉塞Sealing plugZ945/1 套装拉胀喉塞工具Assembly-setZ945/2 套装拉胀喉塞工具Assembly-setZ947/1 拉胀工具延长杆Extended scale tube Z947/2 拉胀工具延长杆Extended scale tubeZ95 钢管Brass tubeZ96 运水铝质螺旋芯（单）Sp iral coreZ961 运水铝质螺旋芯（双）Sp iral coreZ962 运水针Junction tubeZ964 运水回路胶环（小）Diverting elementZ9641 运水回路胶环（大）Diverting elementZ965 运水胶隔片Plug baffleZ967 隔水片Baffle coreZ968 运水胶质螺旋芯Sp iral coreZ969 运水胶质螺旋芯Sp iral coreZ97 运水针Cascade water junction Z975 特快导热针Heat pipe Z98 耐高温密封胶圈O-RingZ1001 阀针Needle valveZ101 电热喷咀Hot nozzleZ101G 电热喷咀Hot nozzleZ101R 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ101M 电热喷咀Hot nozzleZ1011 电热喷咀内胆Inner part of nozzle Z1011M 电热喷咀内胆Inner part of nozzle Z1015 金属密圭寸圈Metall O-Ring Z103 电热喷咀Hot nozzleZ103G 电热喷咀Hot nozzleZ103R 电热喷咀Hot nozzleZ1031 电热喷胆内胆Inner part of nozzle Z103T 电热喷咀Hot nozzleZ103GT 电热喷咀Hot nozzleZ103RT 电热喷咀Hot nozzleZ103 仃电热喷胆内胆Inner part of nozzle Z103M 电热喷咀Multi ple gate nozzle Z1031M 电热喷胆内胆Inner part of nozzle Z10320 电热喷咀Muitl ple gate nozzle Z10370 电热喷咀Muitl plegate nozzle Z104 电热喷咀Hot nozzleZ104G 电热喷咀Hot nozzleZ104R 电热喷咀Hot nozzleZ1041 电热喷胆内胆Inner part of nozzle Z104E 电热喷咀Hot nozzleZ104GE 电热喷咀Hot nozzleZ1041E 电热喷胆内胆Inner part of nozzle Z104GV 电热喷咀Hot nozzleZ1041V 电热喷咀内胆Inner part of nozzle Z10420 电热喷咀Muitl ple gate nozzle Z1052 圆形隔热垫件Distance ring Z1055 炉头接驳衬套Spure bushingZ106 热流道板ManifoldZ10600 热流道板ManifoldZ1061 密封塞钉P lugZ1062 密圭寸圈Sealing washerZ1063 六角螺丝Hexagon head screwZ1064 保温铝板Reflector sheetZ1067 套装零件Accessory kitZ107 气动针阀Needte valveZ1072 针阀司套Needle guide sleeveZ1073 针阀司套Needle guide sleeveZ1076 圆形隔热垫环Distance ringZ109 过滤器Filter cartridgeZ1095 过滤器Filter cartridgeZ110 发热棒Cartridge heaterZ111 发热棒Cartridge heaterZ1133 发热环Heater bandZ1134 发热环Heater bandZ1138 发热管（可弯曲）Fiexble heaterZ116 套装接线工具Assembly setZ1161 耐高温电线Extension cableZ1162 线耳Crimp type bracketZ1164 耐高温电线Extension cableZ1165 连接管Butt jointZ1166 线耳Cable end sleeveZ1167 套件Assembly kitZ1168 热电偶线Signal cableZ121 隔热板（洞、无洞）Insulating sheetZ1211 隔热板（洞、无洞）Thermal insulating sheetZ122 电热温控器T em perature controllerZ1221 温控器组件ModuleZ1224 插座嵌件Socket insertZ1225 温控器连接线Connection po wer/signal cable Z1226 温控器连接线（转换用）Ada pterZ1227 插座ScoketZ1228 插座ScoketZ1229 插座嵌件InsertZ123 多组温控器Multi zone control systemZ125 温控器T em perature controllerZ126/1 温控器T em perature controllerZ126/2 温控器T em perature controllerZ1261 温控器ModuleZ1262 盖板Cover PlateZ127 插头P lug。