下载文档原格式
品质术语1.ACC:Accept (允收2.REJ: Reject (拒收3.SPEC: Specification(规格4.ZD: Zero Defect (零缺点5.CRI: Critical Defect (严重缺点6.MAJ:Major Defect (主要缺点7.MIN: Minor Defect (次要缺点8.AQL: Acceptable Quality Level (允许品质水准9.SA: Self Accurance (自主检查10.FAI:Firsh Article Inspection (初件检验11.IPQC:In-Process Quality Control(制程品质管制12.FQC:Final Quality Control(最终品质管制13.IQC:Incoming Quality Control(进料品质管制14.IPQA:In-Process Quality Audit (制程查核15.OBA:Out Box Audit(开箱查核16.OQC:Out Quality Control(出货品质管制17.PPM: Parts Per Million (百万分之几18.TQC: Total Quality Control(全面品质管制19.TQM:Total Quality Management(全面品质管理20.QIT:Quality Improvement Team(品质改善小组21.CAR:Correction Action Report(改善行动报告22.TIP:Tip Innovation Plan(提案改善计划23.QCC:Quality Control Circle(品管图24.Plan(计划 DO(执行 Check(检讨 Action(改善 (戴明循环25.5MIE:Man(人 Machine(机器Material(材料 Method(方法Measurement(测量 Environment(环境26.5WIH:When(何时 Where(何地Who(何人 Whet(何事Why(为何 How(如何27.AWG:American Wire Gauge(美国线规28.CSA:Canadian Standant Association(加拿大标准协会29.UL:Underwriters Laboratories Inc(美国保险协会实验室30.ENG:Engineering Change Notice(工程变更通知书31.FMEA:Failure Mode &Effect Analysis(失效模式分析。
品质术语1.ACC:Accept (允收)2.REJ: Reject (拒收)3.SPEC: Specification(规格)4.ZD: Zero Defect (零缺点)5.CRI: Critical Defect (严重缺点)6.MAJ:Major Defect (主要缺点)7.MIN: Minor Defect (次要缺点)8.AQL: Acceptable Quality Level (允许品质水准)9.SA: Self Accurance (自主检查)10.FAI:Firsh Article Inspection (初件检验)11.IPQC:In-Process Quality Control(制程品质管制)12.FQC:Final Quality Control(最终品质管制)13.IQC:Incoming Quality Control(进料品质管制)14.IPQA:In-Process Quality Audit (制程查核)15.OBA:Out Box Audit(开箱查核)16.OQC:Out Quality Control(出货品质管制)17.PPM: Parts Per Million (百万分之几)18.TQC: Total Quality Control(全面品质管制)19.TQM:Total Quality Management(全面品质管理)20.QIT:Quality Improvement Team(品质改善小组)21.CAR:Correction Action Report(改善行动报告)22.TIP:Tip Innovation Plan(提案改善计划)23.QCC:Quality Control Circle(品管图)24.Plan(计划) DO(执行) Check(检讨) Action(改善) (戴明循环)25.5MIE:Man(人) Machine(机器)Material(材料) Method(方法)Measurement(测量) Environment(环境)26.5WIH:When(何时) Where(何地)Who(何人) Whet(何事)Why(为何) How(如何)27.AWG:American Wire Gauge(美国线规)28.CSA:Canadian Standant Association(加拿大标准协会)29.UL:Underwriters Laboratories Inc(美国保险协会实验室)30.ENG:Engineering Change Notice(工程变更通知书)31.FMEA:Failure Mode &Effect Analysis(失效模式分析)。
常见质量管理术语英文所写1、PDCA： Plan、 Do、 Check、Action；策划、实施、检查、处置2、PPAP： Production Part Approval Process；生产件批准程序3、APQP：Advanced Product Quality Planning；产品质量先期策划4、FMEA：Potential Failure Mode and Effects Analysis 潜在失效模式及后果分析5、SPC： Statistical Process Control 统计过程控制6、MSA：Measurement System Analysis 测量系统控制7、CP： Control Plan 控制计划8、QSA： Quality System Assessment 质量体系评定9、PPM： Parts Per Million 每百万零件不合格数10、QM： Quality Manual 质量手册11、QP： Quality Procedure 质量程序文件Quality Planning 质量策划Quality Plan 质量计划12、CMK：机器能力指数13、CPK：过程能力指数14、CAD：Computer-Aided Design 计算机辅助能力设计15、OEE：Overall Equipment Effectiveness 设备总效率16、QFD：Quality Function Deployment 质量功能展开17、FIFO：First in, First out 先进先出18、COPS：Customer Oriented Processes 顾客导向过程19、TCQ： Time、Cost、Quality 时间、成本、质量20、MPS：Management Processes 管理性过程21、SPS：Support Processes 支持性过程22、TQM：Total Quality Management 全面质量管理23、PQA：Product Quality Assurance 产品质量保证（免检）24、QP-QC-QI：质量三步曲质量计划－质量控制－质量改进25、QAF：Quality Assurance File 质量保证文件26、QAP：Quality Assurance Plan 质量保证计划27、PFC：Process Flow Chart 过程流程图28、QMS：Quality Management Systems 质量管理体系29、JIT：Just In Time 准时（交货）30、ERP：Enterprise Requirement Planning 企业需求计划31、QC：Quality Control 质量控制32、QA：Quality Audit 质量审核 Quality Assurance 质量保证33、IQC:In come Quality Control 进货质量控制34、IPQC:In Process Quality Control 过程质量控制35、FQC:Final Quality Control 成品质量控制36、OQC:Out Quality Control 出货质量控制37、4M1E:Man、Machine、Material、Method、Environment 人、机、料、法、环38、5W1H：Why、What、Who、When、Where、How为何/做什么/谁做/时间/地点/如何做39、6S：Seiri、Seiton、Seiso、Seiketsu、Shitsuke、Safety整理、整顿、清扫、清洁、素养、安全40、TRI值：Total Record Injury （三种）可记录工伤值41、SMART精明原则：Specific Measurable Achievable Result Oriented Timed具体的描述、可以测量的、可以通过努力实现的、有结果导向性的、有时间性的企业常用英文缩写5S : 5S管理ABC : 作业制成本制度 (Activity-Based Costing)ABB : 实施作业制预算制度 (Activity-Based Budgeting)ABM : 作业制成本管理 (Activity-Base Management)APS : 先进规画与排程系统 (Advanced Planning and Scheduling)ASP : 应用程序服务供货商（Application Service Provider）ATP : 可承诺量 (Available To Promise)AVL : 认可的供货商清单(Approved Vendor List)BOM : 物料清单 (Bill Of Material)BPR : 企业流程再造 (Business Process Reengineering)BSC : 平衡记分卡 (Balanced ScoreCard)BTF : 计划生产 (Build To Forecast)BTO : 订单生产 (Build To Order)CPM : 要径法 (Critical Path Method)CPM : 每一百万个使用者会有几次抱怨(Complaint per Million)CRM : 客户关系管理 (Customer Relationship Management)CRP : 产能需求规划 (Capacity Requirements Planning)CTO : 客制化生产 (Configuration To Order)DBR : 限制驱导式排程法 (Drum-Buffer-Rope)DMT : 成熟度验证(Design Maturing Testing)DVT : 设计验证(Design Verification Testing)DRP : 运销资源计划 (Distribution Resource Planning)DSS : 决策支持系统 (Decision Support System)EC : 设计变更／工程变更 (Engineer Change)EC : 电子商务 (Electronic Commerce)ECRN : 原件规格更改通知(Engineer Change Request Notice)EDI : 电子数据交换 (Electronic Data Interchange)EIS : 主管决策系统 (Executive Information System)EMC : 电磁相容(Electric Magnetic Capability)EOQ : 基本经济订购量 (Economic Order Quantity)ERP : 企业资源规划 (Enterprise Resource Planning)FAE : 应用工程师(Field Application Engineer)FCST : 预估(Forecast)FMS : 弹性制造系统 (Flexible Manufacture System)FQC : 成品质量管理 (Finish or Final Quality Control)IPQC: 制程质量管理 (In-Process Quality Control)IQC : 进料质量管理 (Incoming Quality Control)ISO : 国际标准组织 (International Organization for Standardization) ISAR: 首批样品认可(Initial Sample Approval Request)JIT : 实时管理 (Just In Time)KM ：知识管理 (Knowledge Management)L4L : 逐批订购法 (Lot-for-Lot)LTC : 最小总成本法 (Least Total Cost)LUC : 最小单位成本 (Least Unit Cost)MES : 制造执行系统 (Manufacturing Execution System)MO : 制令(Manufacture Order)MPS : 主生产排程 (Master Production Schedule)MRO : 请修(购)单(Maintenance Repair Operation)MRP : 物料需求规划 (Material Requirement Planning)MRPII : 制造资源计划 (Manufacturing Resource Planning)NFCF : 更改预估量的通知Notice for Changing ForecastOEM : 委托代工 (Original Equipment Manufacture)ODM : 委托设计与制造 (Original Design & Manufacture)OLAP : 在线分析处理 (On-Line Analytical Processing)OLTP : 在线交易处理 (On-Line Transaction Processing)OPT : 最佳生产技术 (Optimized Production Technology)OQC : 出货质量管理 (Out-going Quality Control)PDCA : PDCA管理循环 (Plan-Do-Check-Action)PDM : 产品数据管理系统 (Product Data Management)PERT : 计划评核术 (Program Evaluation and Review Technique)PO : 订单(Purchase Order)POH : 预估在手量 (Product on Hand)PR : 采购申请Purchase RequestQA : 品质保证(Quality Assurance)QC : 质量管理(Quality Control)QCC : 品管圈 (Quality Control Circle)QE : 品质工程(Quality Engineering)RCCP : 粗略产能规划 (Rough Cut Capacity Planning)RMA : 退货验收Returned Material ApprovalROP : 再订购点 (Re-Order Point)SCM : 供应链管理 (Supply Chain Management)SFC : 现场控制 (Shop Floor Control)SIS : 策略信息系统 (Strategic Information System)SO : 订单(Sales Order)SOR : 特殊订单需求(Special Order Request)SPC : 统计制程管制 (Statistic Process Control)TOC : 限制理论 (Theory of Constraints)TPM : 全面生产管理Total Production ManagementTQC : 全面质量管理 (Total Quality Control)TQM : 全面品质管理 (Total Quality Management)WIP : 在制品 (Work In Process)5S管理5S是由日本企业研究出来的一种环境塑造方案，其目的在藉由整理(SEIRI)、整顿(SEITON)、清扫(SEISO)、清洁(SEIKETSU)及身美(SHITSUKE)五种行为来创造清洁、明朗、活泼化之环境，以提高效率、品质及顾客满意度。
英文质量术语从事质量多年，但在交流的时候仍会对一些术语（英文简称）搞不清楚，现普及一下部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control 生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA)CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力)PMP:制程管理计划（生产管制计划）MPI:制程分析DAS efects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery（品质，交期，成本）MPM:Manufacturing project management制造专案管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造(Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理(Just In Time)QCC ：品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划(Distribution Resource Planning)DSS：决策支持系统(Decision Support System)EC ：电子商务(Electronic Commerce)EDI ：电子资料交换(Electronic Data Interchange)EIS ：主管决策系统(Excutive Information System)ＥＲＰ：企业资源规划(Enterprise Resource Planning) FMS ：弹性制造系统(Flexible Manufacture System)KM ：知识管理(Knowledge Management)4L ：逐批订购法(Lot-for-Lot)LTC ：最小总成本法(Least Total Cost)LUC ：最小单位成本(Least Unit Cost)MES ：制造执行系统(Manufacturing Execution System) MPS ：主生产排程(Master Production Schedule)MRP ：物料需求规划(Material Requirement Planning) MRPⅡ：制造资源计划(Manufacturing Resource Planning) OEM ：委托代工(Original Equipment Manufacture) ODM ：委托设计与制造(Original Design & Manufacture) OLAP：线上分析处理(On-Line Analytical Processing) OLTP：线上交易处理(On-Line Transaction Processing) OPT ：最佳生产技术(Optimized Production Technology) PDCA：PDCA管理循环(Plan-Do-Check-Action)PDM：产品数据管理系统(Product Data Management)) RCCP：粗略产能规划(Rough Cut Capacity Planning) SCM ：供应链管理(Supply Chain Management)SFC ：现场控制(Shop Floor Control)TOC：限制理论(Theory of Constraints)TQC ：全面品质管制(Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和。
品质管理常用英文术语在品质管理领域，有许多常用的英文术语，对于从事相关工作的人员来说，熟悉这些术语是至关重要的。
下面就为大家介绍一些常见的品质管理英文术语。
一、基础术语1、 Quality 质量这是品质管理中最基本的概念，指产品或服务满足规定或潜在需要的特征和特性的总和。
2、 Quality Control （QC) 质量控制通过一系列的检验、测试和监控活动，确保产品或服务符合规定的质量标准。
3、 Quality Assurance （QA) 质量保证是为了提供足够的信任表明实体能够满足质量要求，而在质量管理体系中实施并根据需要进行证实的全部有计划和有系统的活动。
4、 Inspection 检验对产品或服务的一个或多个特性进行测量、检查、试验或度量，并将结果与规定要求进行比较以确定每项特性合格情况的活动。
5、 Test 测试通过特定的方法和设备，对产品或服务的性能、功能等方面进行检测和评估。
二、缺陷相关术语1、 Defect 缺陷产品或服务中存在的不符合规定要求的情况。
2、 Nonconformity 不合格未满足规定的要求。
3、 Minor Defect 轻微缺陷对产品或服务的功能和使用影响较小的缺陷。
4、 Major Defect 重大缺陷对产品或服务的功能和使用有较大影响的缺陷。
5、 Critical Defect 致命缺陷可能导致人身伤害、严重安全隐患或完全丧失产品或服务功能的缺陷。
三、统计分析术语1、 Statistical Process Control （SPC) 统计过程控制使用统计技术来监控和控制过程，以确保过程处于稳定状态并能够满足质量要求。
2、 Control Chart 控制图用于监控过程稳定性和识别过程变异的图表。
3、 Mean 均值一组数据的算术平均值。
4、 Median 中位数将一组数据按大小顺序排列后，位于中间位置的数值。
5、 Mode 众数一组数据中出现次数最多的数值。
品质治理常用英文术语缩写英文对比中文术语8D 8 Disciplines Of Solving Problem 解决问题8步法AC./RE. Acceptable / Rejective 允收/拒收AQL Acceptable Quallity Level 允收水准ABB Activity-Based Budgeting 实施作业制预算制度ABC Activity-Based Costing 作业制本钱制度ABM Activity-Based Mangement 作业制本钱治理APS Advanced Planning And Scheduling 应用程式效劳供给商APQP Advanced Product Quality Planning 先期产品品质规划ANOV A Analysis Of Variance 方差分析AAR Appearance Approval Report 外观成认汇报AC Appraisal Cost 鉴定本钱ASL Approved Suplier List 合格供给商清单A VL Approved Vendor List 认可的供给商清单ATP Available To Promise 可承诺量BSC Balanced Score Card 平衡记分卡BOM Bill Of Material 材料明细BTF Build To Forecarst 方案生产BTO Build To Order 订单生产BPR Business Process Reengineering 企业流程再造CPK Capability Of Process修正过程能力指数Ca. Capability Of Accuraty X度指数Cp. Capability Of Precesion 周密度指数CRP Capacity Requirement Planning 产能需求规划C. OF C. Certificate Of Compliance 〔质量〕承诺证明书CEO Chief Excutive Officer 执行总裁CQC Companywide Quality Control 全公司范围的品质治理CPM Complaint Per Illion 每百万报怨次CAD Computer Aided Design 计算机辅助设计CTO Configuration To Order 客制化生产CRC Contract Review Committee 合约评审委员会CIF Cost Inusance And Freight 到岸价格COQ Cost Of Quality 品质本钱CPM Critical Path Method 要径法CTQ Critical Quality 关键质量CAR Crrective Action Report改正措施汇报CRM Customer Relationship Management 客户关系治理CR Customer's Risk 消费者冒险率DSS Decision Support System 决策资源系统DS/SS Def.Size/Sample Size 缺点数/样品数DPU Defect Per Unit 单位缺陷数DPMO Defects Per Million Opportunity 百万个时机中的缺陷数DMADV Define\Measurement\Analysis\Design\Verify 确定、测量、分析、设计、验证DMAIC Define\Measurement\Analysis\Improvement\Control 确定、测量、分析、改善、操纵DEPT. Department 部门DMT Design Matuing Testing 成熟度验证DOE Design Of Experiment 实验设计DVT Design Verification Testing 设计验证DRP Distribution Resource Planning 运销资源方案DTS Dock To Stock 免验DCC Document Control Centre 文管中心DBE Drum-Buffer-Rope 限制驱导式排程法EOQ Economic Order Quantity 根本经济订购量EMC Electric Magnetic Capability 电磁相容EC Electronic Commerce 电子商务EDI Electronic Data Imterchange 电子资料交换EC Engenering Change工程变更ECN Engenering Change Notice工程变更通知ECRN Engineer Change Request Notice 原件规格更改通知ERP Enterprise Resource Planning 物料需求方案EI&PM Employee Involvement participative Management 全员参与法EIS Executive Information System 主管决策系统FAE Field Application Engineer 应用工程师FQC Finish Or Final Quality Control 成品品质管制FAI First Article Inspection 首件检验FMEA Failure Mode And Efects Analysis 失效模式及效应分析Yft First Time Yield 第—次通过率FMS Flexible Manufacture System 弹性制造系统FCST Forecast 预估FOB Free Of Board 离岸价G R&R Gauge Reproducility Repeatability 量具再现性与再生性GWQC Groupwide Quality Control 全集团范围的品质治理IQC Incoming Quality Control 进料品质管制ISAR Initial Sample Approval Request 首批样品认可IPQC In-Process Quality Control 过程品质管制ISO International Standardization Orgnization 国际标准化组织JIT Just In Time 即时治理KCP Key Control Point 关键操纵点KM Knowledge Management 知识治理LDPU Latent DeFect Per Unit 单位产品潜在缺陷LTC Least Total Cost 最小总本钱法LUC Least Unit Cost 最小单位本法LS Lobour Scrap 工时损失LRR lot Rejective Rate 批退率LTPD Lot Tolerance Percent Defective 拒收水准L4L Lot-For-Lot 逐批订购法LCL Lower Control Limit 下操纵界限LSL Lower Specification Limit 下规格界限MRO Maintenance Repair Operation 请修〔购〕单MIS Management Information System资讯系统MO Management Order 制令MES Manufacturing Execution System 制造执行系统MRP-II Manufacturing Resourece Planning 制造资源规划MPS Master Production Scheduling 主生产排程MRP Material Requirement Plan 物料需求规划MRB Material Review Board物料鉴审委员会MSDS Material Safety Data Sheet 物质平安资料表MS Material Scrap 材料报废MTBF Mean Time Between Failure 平均故障间隔时间MSA Measurement System Analysis测量系统分析NG Not Good 不良OLAP On-Line Analytical Processing 线上分析处理OLTP On-Line Transaction Processing 线上交易处理OPT Optimized Production Technology 最正确生产技术ODM Original Design Manufacture 托付设计与制造OEM Original Equeitpment Manufacture 原始设备制造商/托付代工OQC Out-Going Quality Control 出货品质管制PPM Part Per Million 百万分之……PDCA Plan Do Check Action PDCA治理循环PSO President Staff Office 总经理办公室PM Prevention Mmaintenance 预防维护PC Preventive Cost 预防本钱PR Producer's Risk 生产者冒险率PDM Product Data Management 生产资料治理系统POH Product On Hand 预估在手量PPAP Production Part Approval Process 生产品核工业准程序PERT Program Evaluation And Review Technique 方案评核术P/O Purchase Order 订单QA Quality Assurance 质量保证QC Quality Control 质量管制QCC Quality Control Circle 品管圈QCFS Quality Control Flow Sheet 品质操纵流程图QDN Quality Deviation Notice品质异常通知QDR Quality Deviation Request 品质异常回复QE Quality Engineering 品质工程QFD Quality Function Depioyment 品质功能展开QIT Quality Improvement Team 品质改善团队QIS Quality Information System 品质信息系统QS9000 Quality System 9000 品质系统9000QSA Quality System Assessment 品质系统评鉴ROP Re-Order Point 再订购点R&D Reserrch And Development 研究开发RMA Returned Material Approval进货验收RC Rework Cost 返工费用RPN Risk Priority Number风险领先指数Yrt Rolled Thoughtput Yield 全过程通过率RCCP Rough Cut Capacity Planning 粗略产能规划S S 样本偏差SO Sales Order 订单SFC Shop Floor Comtrol 现场操纵σ Sigma 标准差SOR Special Order Request 特别订单需求SPEC. Specification 标准/规格SDCA Standardzation Do Check Action SDCA治理循环SPC Statistical Process Control 过程统计操纵SIS Strategic Information System 策略资讯系统SWOT Strength\ Weakness \Oportunity\ Treats 企业SWOT分析资料SQD Supplier Quality Develepment 供给商品质开发SCM Supply Chain Management 供给链治理TOC Theory Of Constraints 限制理论Ytp Thoughtout Yield 过程通过率TMC Total Manufacture Cost总制造本钱TPM Total Production Management 全面生产治理TQM Total Quality Management 全面品质治理UCL Upper Control Limit 上操纵界限USL Upper Specification Limit 上规格界限WIP Work In Process 在制品Xbar X bar X平均值。
品质管理英文术语大全1. IntroductionIn the field of quality management, it is important to have a good understanding of the various terminology used. This document provides a comprehensive list of quality management terms in English.2. Quality Management Terms2.1 Quality•Quality: The degree to which a product or service meets the requirements and expectations of customers.•Quality Assurance: The process of systematically ensuring that a product or service meets specified requirements.•Quality Control: The process of checking that a product or service meets specified requirements.2.2 Quality Management Systems•ISO 9001: The international standard for quality management systems.•Quality Policy: A formal statement by an organization of its overall intentions and direction pertning to quality management.•Quality Objectives: The specific goals and targets set by an organization with respect to quality management.•Process Approach: Managing activities and resources as processes to achieve desired outcomes.2.3 Quality Planning•Quality Planning: The systematic process of identifying the quality-related activities that need to be performed to ensure that objectives are achieved.•Quality Metrics: The measurements used to evaluate the performance of processes, products, and services.•Risk Management: The process of identifying, assessing, and prioritizing risks to minimize or eliminate their impact on project objectives.2.4 Quality Assurance•Quality Audit: An independent examination to determine whether quality activities and related results comply with planned arrangements.•Supplier Quality Assurance: The process of assessing and ensuring the quality of products or services provided by suppliers.•Quality Management Review: An evaluation of the effectiveness and suitability of the quality management system.2.5 Quality Control•Statistical Process Control: The use of statistical techniques to monitor and control processes to ensure their stability and predictability.•Inspection: The process of examining a product or service to determine its conformity to specified requirements.•Defect: A nonconformance of a product or service with specified requirements.2.6 Continuous Improvement•Plan-Do-Check-Act (PDCA): A four-step iterative process for achieving continuous improvement.•Kzen: A Japanese term meaning continuous improvement.•Six Sigma: A data-driven approach forimproving the quality of processes by reducing variation and defects.3. ConclusionThis document has provided a comprehensive list of quality management terms in English. It is important for professionals in the field of quality management to have a good understanding of these terms in order to effectively communicate and implement quality management practices.。
质量管理体系术语中英文对照以下是部分质量管理体系相关的基本术语中英文对照：1.质量管理体系（Quality Management System, QMS）o中文：质量管理体o英文：Quality Management System2.质量管理（Quality Control, QC）o中文：质量管理o英文：Quality Control3.持续改进（Continuous Improvement, CI）o中文：持续改进o英文：Continuous Improvement4.过程方法（Process Approach）o中文：过程方法o英文：Process Approach5.质量方针（Quality Policy）o中文：质量方针o英文：Quality Policy6.质量目标（Quality Objectives）o中文：质量目标o英文：Quality Objectives7.内部审核（Internal Audit）o中文：内部审核o英文：Internal Audit8.纠正措施（Corrective Action）o中文：纠正措施o英文：Corrective Action9.预防措施（Preventive Action）o中文：预防措施o英文：Preventive Action10.顾客满意度（Customer Satisfaction）o中文：顾客满意度o英文：Customer Satisfaction11.供方管理（Supplier Management）o中文：供应商管理o英文：Supplier Management12.产品实现（Product Realization）o中文：产品实现o英文：Product Realization13.设计和开发（Design and Development）o中文：设计与开发o英文：Design and Development14.测量、分析和改进（Measurement, Analysis andImprovement）o中文：测量、分析与改进o英文：Measurement, Analysis and Improvement 以上内容主要参考了ISO 9001:2015质量管理体系标准中的核心概念。
品质管理的英文术语大全品质专业英语大全品质专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory （电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor （互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条码System：系统System Barcode：系统条码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Riser card：转接卡Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control 生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力) PMP:制程管理计划（生产管制计划）MPI:制程分析DAS efects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册A VL ：认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery（品质，交期，成本）MPM:Manufacturing project management制造专案管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造(Business Process Reengineering) ISAR ：首批样品认可(Initial Sample Approval Request)- JIT：实时管理(Just In Time)QCC ：品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划(Distribution Resource Planning)DSS：决策支持系统(Decision Support System)EC ：电子商务(Electronic Commerce)EDI ：电子资料交换(Electronic Data Interchange)EIS ：主管决策系统(Excutive Information System)ＥＲＰ：企业资源规划(Enterprise Resource Planning)FMS ：弹性制造系统(Flexible Manufacture System)KM ：知识管理(Knowledge Management)4L ：逐批订购法(Lot-for-Lot)LTC ：最小总成本法(Least Total Cost)LUC ：最小单位成本(Least Unit Cost)MES ：制造执行系统(Manufacturing Execution System) MPS ：主生产排程(Master Production Schedule)MRP ：物料需求规划(Material Requirement Planning) MRPⅡ：制造资源计划(Manufacturing Resource Planning) OEM ：委托代工(Original Equipment Manufacture) ODM ：委托设计与制造(Original Design & Manufacture) OLAP：线上分析处理(On-Line Analytical Processing) OLTP：线上交易处理(On-Line Transaction Processing) OPT ：最佳生产技术(Optimized Production Technology) PDCA：PDCA管理循环(Plan-Do-Check-Action)PDM：产品数据管理系统(Product Data Management)) RCCP：粗略产能规划(Rough Cut Capacity Planning) SCM ：供应链管理(Supply Chain Management)SFC ：现场控制(Shop Floor Control)TOC：限制理论(Theory of Constraints)TQC ：全面品质管制(Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceablity 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: V oice of Customer 客户需求136 VOE: V oice of Engineer 工程需求137 Inventory stock report:庫存清单报告138 Sales order report:出货报告质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessA VL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板riser card 扩充卡flat cable 排线TOP driver cage 上磁架bottom driver cage 下磁架resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机club car高尔夫球车plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模stage die工程模compound die复合模shearing die剪边模riveting die铆合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 换模to fix a die装模to repair a die修模punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上垫板top plate上托板（顶板）top block上垫脚stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块die locker锁模器pressure plate =plate pinch压板thickness gauge厚薄规cutting die, blanking die冲裁模die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条panel board镶块to load a die装上模具to unload a die 御模具active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块pilot导正筒trim剪外边pierce剪内边pocket for the punch head挂钩槽slug hole废料孔radius半径shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺丝form block折刀round pierce punch =die button圆冲子shape punch =die insert异形子stock located block定位块metal plate钣金miller铣床grinder磨床tolerance公差score =groove压线sliding block滑块lathe车active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板capability能力parameter参数factor系数driller钻床set up die架模height of die setting up架模高度analog-mode device类模器inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves =spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套press specification冲床规格die height闭模高度flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝stripper plate脱料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold挤压式模具split mold分割式模具die lifter举模器top stop上死点bottom stop下死点one stroke一行程to continue, cont.连动to grip(material)吸料location lump, locating piece, location block定位块reset复位to file burr 锉毛刺embedded lump |in'bed| |l mp|镶块stamping-missing漏冲to tight a bolt拧紧螺栓to loosen a bolt拧松螺栓punched hole冲孔to cut edge =side cut =side scrap 切边to bending折弯to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake铆合designing, to design设计design modification 设计修改成gauge(or jig)治具pedal踩踏板stopper阻挡器flow board流水板torque扭矩spline =the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的forming成型(抽凸,冲凸)draw hole抽孔bending折弯emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线stamp letter冲字(料号)tick-mark nearside正面压印tick-mark farside反面压印冲压类punch, press冲punching machine 冲床hydraulic machine油压机jack升降机decoiler整平机manufacture management制造管理stamping, press冲压feeder送料机rack, shelf, stack料架taker取料机to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削robot机械手production line流水线packaging tool打包机packaging打包成型类well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针。
