模具方面的中英文对照

查看文章模具方面的中英文对照塑料成型模具的主要设计要素脱模距 stripper distance脱模斜度 draft投影面积 projected area最大开距 maximum daylight;open daylight闭合高度 mould-shut height抽芯距 core-pulling distance抽芯力 core-pulling force脱模力 ejector force开模力 mould opening force模内压力 internal mould pressure;cavity pressure 成型压力 moulding pressure背压环 back-up ring1 bar = 14.5psi高压接头 bite type fitting液压马达 hydraulic motor冷却水流量计 waterflow regulator打磨器材 abrasive material打磨砂轮 grinding wheels切割砂轮 cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools高压力软管 high pressure hose风管,水软管 air .water hose高压油表 pressure gauge压力油喉 hydraulic hoses光塑检测 photoelastic testing吹塑模 plastic blow mould注塑模 plastic injection mould冲扎复合模 blank & form compound die精密冲模 precision blanking die熔料流动率 MFR=melt flow rate熔料流动指数 MET=melt flow index推板导柱 guide pin for ejector plater座板 clamping plate垫块 space block(plate)推板 ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形 distortion弯曲 warp拖花 drag marks火花纹 EDM marks困气 venting烧黑 burns表面缩水 shrinkage料位过薄/砸穿 thin wall stock走水不平行 uneven fill pattern夹水纹/流纹 witness line;mismatch;stress marks 走水纹 knit lines走水不齐 short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力 side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒,lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用) air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离) clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层。

模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。

压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。

气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。

流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。

模芯Parting Core / 局部视图Partial View / 冷料# Cold Slag / 线切割Wire E.D.M / 轮廊Contour/螺纹孔Tapping Hole / 连接件Fittings / 斜针Angle Pin / 接合Engage替换镶件Interchangeable Mold Inserts / 指定吨位的注塑机Specific Press水嘴接头Water Fittings / 螺纹Eyebolt Thread / 回针Stop Pin二级顶出针Sub-Leaderd Pin / 镶件Mold Insert/加硬Harden唧嘴Sprue / 设计筒图Design Preliminary / 名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A'plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High V olume Running Mold剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension雕刻Engrave托司EJ.GUIDE PINGating TypeSprueEdge/TabSubPin PointFanCashewHot Sprue/TipHot ValveHot RunnerOther: Best case gating in order for the parts to de-gate at ejection旋转镶件circumvolve Insert螺纹抽芯Thread action insert电镀plating备件spare part弯头elbow组装、冲压、喷漆等专业词汇Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条形码 barcode scanner条形码扫描仪 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造技术 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs.inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板chassis |'∫æsi| 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接柆键 sheet metal parts 冲件 plastic parts塑料件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |'plein?|刨床 miller铣床 grinder磨床 driller钻床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager |'depjuti| =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |'skræpid|报废 scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation |' ksi'dei?n|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embeded lump|in'bed| |l?mp|镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper 扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots 水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering 工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker 模工 production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱 to pull and stretch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation评估 prepare for, make preparations for 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch---to throw--over switching over切换 engineering, project difficulty工程瓶颈 stage die 工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder 油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice 通知 application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die 冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch 拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量 quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品 incoming material to be inspected进货待验 description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting minutes会议记录 meeting type 会别 distribution department分发单位 location地点difference quantity 差异量 cause analysis原因分析 raw materials原料 materials物料 finished product成品 semi-finished product半成品 packing materials包材 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓 spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch head挂钩槽 slug hole废料孔 feature die公母模 expansion dwg 展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert 异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 club car高尔夫球车 capability能力 parameter参数 factor系数 phosphate 皮膜化成 viscosity涂料粘度 alkalidipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄咬 desmut 剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条形码 flow chart流程窗体 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate坐标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疪 shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring 镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄轴 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键 quenching淬火 tempering 回火 annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机模具工程类 plain die简易模 pierce die冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质 material thickness料片厚度 factor系数 upward向上 downward向下 press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 weight重量 total wt.总重量 punch wt.上模重量五金零件类 inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销 coil spring弹簧 lifter pin顶料销 eq-height sleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销 wire spring圆线弹簧 outer guiding post外导柱 stop screw止付螺丝 located pin定位销 outer bush外导套模板类 top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块电镀plating。

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割 Wire E.D.M轮廊Contour螺纹孔 Tapping Hole连接件 Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针 Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner V ents抛光Draw Polish侧抽芯 Side Action加强筋 Reinforcing三角撑 Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting 装卸孔 Handling Hole运输安全带 Moldstrap码模槽 Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location耐落胶 Teflon Paste偏移量 Offset水塞Water Line Plug撬模脚 Ppy Slot重新加工Reworked配件Components补偿Compensation平面度 Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机 Edm熔接线 Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰 Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板Ejector Retainer Plate垫板 Retainer Plate后模镶针Core Pin拉圾钉 Stop Pin有托顶针Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套 Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet V alve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速项 Accelerated Ejector客户 Client产品名 Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件 Sub-Insert下模小镶件 Core Sub-Insert上模小镶件 Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机） Jaw硬片（摩擦片） Wear Plate水口铁 Runner Bar上模水口铁 Upper Runner Bar下模水口铁 Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁 Side Lock斜度锁 Interlock锁模板 Safety Bar‘O’令（密封圈） O'Ring喉塞Plug隔水片 Baffle波子螺丝（行位定位螺丝） Ball-Catch斜顶Lifter控制开关Switch回针 Return Pin斜导柱 Angle Pin推板 Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板 Ejector Plate顶针底板Ejector Retainer Plate垫板 Retainer Plate垃圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套 Runner Stripper Plate Bushing定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet V alve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速顶 Accelerated Ejector扁顶 Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板 Backup合模Shutoff空隙槽 Clearance Slot导柱及导套 Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具 Thermoset Mold三板模 3-Plat Mold分型面 Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板 Retainer Plate顶出板 Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器 Bumper衬垫Cushion公差Tolerance突然性动作 Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模 Sticking Core粘水口 Sticking Sprue夹水纹 Weld Line变形 Warpage走水不平均 Filling Uneven走不齐 Short Shot挂成品 Part Hanging漏水 Water Leakage刮花（擦伤）Galling困气 Air Trapping温度 Temperature注塑模※※※※ction Mold 入水 Gate试板 Sampling压力 Pressure倒圆 Fillet顶棍 Ejector顶白 Stress Mark粘前模 Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边） Angle PinA板 A'plateB板 B'plate倒扣 Under-Cut披峰 Flash缩水 Sink Mark氮化 Nitride不规则四边形Trapezoid连续的 Consecutive雕刻 Engrave出模角 Draft分模面 Parting Surface擦位 Shut-Off(S/0)导套 Bushing回针 Return Pin加硬 Harden唧嘴 Sprue设计筒图Design Preliminary丝印 Silkprint不干胶 Adhesive Sticker导向针 Guide Din公差 Tolerance线切割 Wire-Cut电火花 Edm抛光 Polishing蚀纹 Texture探热针 Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板 Cover Plate齿轮 Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料# Cold Slag线切割 Wire E.D.M.轮廓 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leader Pin镶件 Mold Insert锁定位 Lock楔子(铲鸡) Wedge高产量模量 High V olume Running Mold 剖面图 Cross Section模具结构Mold Construction 模芯 Parting Core局部视图Partial View热流道 Manifold热嘴 Hot Nozzle型腔数 Cav No模号 Mold No胶料 Material尺寸 Dimension重要尺寸Critical Dimension 雕刻 Engrave托司 EJ.GUIDE PIN。

模具专业术语中英文对照模具Mold模胚Mold Base分模线Parting Base母模线Parting Line公模侧Core Side嵌板Mold Plate嵌件Insert滑块板Slider滑块板固定板Wear Plate斜针Angular Ejector组装板Back Plate第二固定板Runner Stripper Plate 顶针板Ejector Plate方铁Spacer Block定位圈Locating Ring导柱Guide Pin撑顶Support Pin定位杆Stop Bolt小拉杆Pull Bolt导柱套Guide Bush水口针Runner Lock Pin斜导柱Angular Pin锁定块Heal Block回针Return Pin垃圾针Stop Ring顶出板导柱Ejector Guide弹簧Coil Spring支撑柱Support Pillar顶针Ejector Pin板顶针Blade Ejector顶块顶出Block Ejector顶板顶出Plate Ejector司筒顶出Sleeve Ejector中心针Center Pin机嘴套Spure Bush直流道Sprue流道Runner支流道Drop 定位机构Inter Lock吊圈Eye Bolt日期转印Date Mark前模Cavity后模Core型心Core Pin出模编号Cavity Number冷却管Cooling Channel水嘴Hose Nipple冷却棒Baffle加热管Heat PipeO形圈O Ring逃气孔Air Vent销针Dowel Pin铣床加工Milling Machining放电加工EDM Machining线切割加工Wire Cutting磨床加工Grinding孔位加工Drilling细加工Deburring省模加工Polishing配模Fitting塞规Shim铜公EDM Master筋骨加工Rib Machining脱模斜度Draft Angle倒扣Under Cut钢材Steel咬花Texture雕刻加工Engraving电镀加工Electro Plating热处理Hardening氮化处理Nitrding表面处理Surface Hardness内六角螺钉Allen Bolt热流道Hot Runner热流道结构Manifold热嘴Hot Tip注塑Injection树脂Resin材料Material等级/类型Grade干燥Dry干燥不足Not Dried Enough收缩率Shrinkage充填Full Shot比重Density调温机Temp Cont Unit热可塑性Thermo Plastis热硬化性Thermo Set银条状Silver Line喷流痕Flow Mark侠水纹Weld Line披峰Burr缩水Sink mark烧焦Burn Mark充填不良Short Shot光泽不良Gloss Not Enough气泡Bloe Hole难型不良Sticking弯曲Bending变形Warpage光泽不均Uneven Gloss难物不良Black Spot打痕Damage顶白White Mark谬丝Hair Flash拉伤Scrtach油污点Oil Dirt裂化Crack倒塌Deform分模定位锁Parting Lock水口Gate点水口Pin Gate侧水口Side Gate潜伏水口Submarine Gate。

assemble mould合箱assembling mould装配铸型baked mould干型bar mould多穴压模big-end-up mould上大下小钢锭模black mould of rice 黑变病blank mould turnover 雏型模翻转blowing mould吹模blue mould of citrus 柑桔青霉病cap mould压顶线脚car type mould conveyor 小车式铸型输送机case mould plaster 母模用石膏casting mould铸型centrifugal casting mould离心铸造铸型ceramic mould casting 陶瓷模注法channel mould槽模chill mould冷铸型(模)close mould封闭铸型close mould (铸造用) 合箱closed mould闭式模; 闭式压模cold-punching mould冷冲模collapsible mould分室模composite ceramic mould复合陶瓷型composite mould casting 复合型铸造copper mould base 铜模底copper mould wall 铜坩埚壁corrugated mould波形铸模cover mould压缝线脚covered floor mould盖箱地面铸型cylinder mould machine 圆网造纸机double-mould-broad ridging plough 双壁起垄犁draw mould薄壁模子driel mould干型drip mould滴水线脚dry sand mould干型ear mould耳模electric pole mould hanger 电杆模型吊架end mould端模Erical mould可压锭模; 挤压锭模evacuated mould空腔模face mould面模fall wheat snow mould冬小麦雪霉病falling mould曲型线条female mould阴模fixed mould固定模flaskless mould无箱铸型floating-point mould浮点模型floor mould地铸模fluted mould波形模foam sponge mould泡沫胶硫化模footed mould压印底圈的模型forging mould锻模front mould前模full-mould casting process 实型铸造gang mould成组模; 成组模板garden mould园土get in the mould垫平铸型glass mould玻璃型; 玻璃铸型glass mould diode 玻璃模二极管graphite mould石墨型grass mould腐草土gray mould灰霉green mould绿霉病green mould of citrus 柑桔绿霉病ground mould地面铸型; 堆土木模gypsum mould石膏型hair mould毛霉hair mould sprout 毛霉芽half mould半型hoist for mould board carrier 模板车升降机hump mould压坯用阳模ice mould冰铸ingot mould钢锭模; 铸锭模; 铸锭型; 锭模ingot mould milling machine 钢锭模铣床ingot slab mould扁钢锭模insulating mould coating 隔热涂料integral mould整模型invested mould熔模铸型iron mould铁锈迹leaf mould叶霉; 腐叶土loam mould泥型lower mould half 下模; 凹模male mould凸模; 阳模master mould母型; 原模mismatch in mould铸型错箱mould印模; 模; 模板; 模具; 模筛样板; 模塑; 模子; 成型模具; 圆网; 造型模板; 塑模; 霉; 霉病; 霉菌; 纸型mould addition 钢锭模添加剂mould and die milling machine 模具铣床mould assembling 合箱mould assembling and closing 铸型合箱mould assembly 合型mould blower 吹型机mould board 造型板; 样板mould boardless plough 无壁犁mould buggy 钢锭模车mould case 模制壳mould clamp 卡具mould clamps 模型紧固夹mould cleaner 模具清洁剂mould closer 合箱机; 合箱装置mould coating material 钢锭模涂料mould core 模芯mould cover 腐殖质层mould cure 模塑硫化; 模型硫化mould dam aged sweet potato poisoning 黑斑甘薯中毒mould dimension 铸型尺寸mould drag 下半箱mould drying 铸型烘干mould efficiency 模塑效率mould emptier 脱模机构mould erosion 铸型冲蚀mould facing 涂料mould fitter 合箱工mould flat gauge 样板mould form 模型型腔mould fungus 霉菌mould growth test 长霉试验mould half 半型mould hardness 铸型硬度mould impression 模型内腔; 模型型腔; 模穴mould in a snap flask 无箱造型mould in the pit 地坑造型mould inoculation 型内孕育mould jacket 型套mould kernel 模芯mould life 模型寿命mould lifting 铸型起模mould lining 坩埚衬里mould loft 放样间mould loft floor 放样台mould lofter 放样工; 放样工人mould loftsman 放样工; 放样工人mould machine 模塑机mould machine of cereal seed selection 谷物选种机mould mark 模缝条痕mould matrix cathode 模制阴极mould oil 脱模油mould on end 垂直分型造型mould pig iron 型铁mould plaster 模型用石膏mould plate 模型板mould plunger 阳模mould plunger force plug 凸模mould preparation bay 钢锭模准备跨mould press 模压机mould pressing 旋压成形mould proofing 防霉mould rains 梅雨mould release 分型粉mould relese 脱模mould rollover unit 翻箱装置mould sand 型砂mould seam 模缝mould setting-and-stripping bay 钢锭模准备和脱锭跨mould shift 错箱mould shrinkage 模内收缩; 模压收缩; 脱模后的收缩mould splits 模组分mould stripping 铸型起模; 拆模mould susceptibility 感霉性mould test chamber 霉菌试验箱mould train 模组mould turnover 翻箱mould unloading 出模; 脱模; 卸模mould veining 铸型裂纹mould vibrator 模板振动器mould vulcanization 模塑硫化mould wash 脱模涂料mould wash mixer 涂料搅拌机multiple cavity mould多型腔铸型; 多巢模multiple mould多件石膏模multiple-part mould多箱铸型needle mould针模one-piece mould整体铸型open bottom mould底开式钢锭模open mould明浇铸型; 敞口铸型open sand mould明浇砂型optical instrument mould and fog auto-detector 光学仪器霉雾自动检测仪ornamental mould艺术造型pallet conveyer mould machine 滑板输送式造型机paper mould纸型paste mould衬碳模paste mould ware 衬碳模成形的制品peat mould泥炭土permanent mould永久铸型pig mould锭模plural mould operation 多模操作porous mould多孔模型positive mould阳模; 阳压模press mould压模press mould ware 模压器皿pressing mould压模process of unconventional heat treatment of mould模具非常规热处理工艺quadrant mould四开木压条real mould实模型rectal suppository mould肛门栓剂模refractory shell mould耐火材料壳型removal of the mould拆模reverse mould倒模; 倒型revesing permanent mould双面金属型ring mould瓶颈模ring-shaped mould环型铸模risk of mould发霉险roast sand mould干砂型rubber mould橡胶皮模running mould模筛样板; 模饰样板saccharifying mould糖化霉sealing of a mould铸型密封section mould型模sectional mould镶合砂型semi-automatic mould半自动模; 半自动塑模semi-chilled mould casting 半金属型铸造; 半冷模铸造semi-permanent mould半永久型; 半永久性模semiclosed top mould半封顶锭模shell mould machine 壳型造型机shiftable mould-board 可拆换的刀片sign mould符号模型single cavity mould整体铸型single mould单件模型skin dried mould面干铸型skin drying mould表干型sleeper steel mould轨枕钢模slime mould粘菌slip flask mould脱箱铸型snap flask mould活箱造型; 无箱铸型snapflask mould脱箱造型snow mould雪霉病; 雪疫病soap mould皂模sooty mould烟霉; 煤污病sooty mould of rice plant 水稻煤病sooty mould of tea 茶叶煤污病spacing mould隔膜split mould对开模stagnant mould不动模型standard steel ingot mould标准钢锭模steel mould钢锭模; 钢模steel mould for electric pole 电杆钢模stock mould定型模stripper-plate mould脱模板塑模sweeping loam mould刮泥型swell of a mould胀砂symbol mould符号模型tape of mould模型锥度thin-walled metal mould薄壁金属型thin-walled mould薄壁结晶器three-cavity mould三开箱铸型tilt-mould billet 可倾模锭坯tire recapping mould轮胎翻修硫化机tomato leaf mould番茄叶霉病top mould half 凸模two-cavity mould双型腔铸型variable-point-mould变点模型vegetable mould腐殖土verge mould山墙檐口线脚waste mould gypsum 废模石膏watch-case mould表壳式压模water mould水霉wood casting mould木质铸造模型X-mould machine 多模成型机。

assemble mould合箱assembling mould装配铸型baked mould干型bar mould多穴压模big-end-up mould上大下小钢锭模black mould of rice 黑变病blank mould turnover 雏型模翻转blowing mould吹模blue mould of citrus 柑桔青霉病cap mould压顶线脚car type mould conveyor 小车式铸型输送机case mould plaster 母模用石膏casting mould铸型centrifugal casting mould离心铸造铸型ceramic mould casting 陶瓷模注法channel mould槽模chill mould冷铸型(模)close mould封闭铸型close mould (铸造用) 合箱closed mould闭式模; 闭式压模cold-punching mould冷冲模collapsible mould分室模composite ceramic mould复合陶瓷型composite mould casting 复合型铸造copper mould base 铜模底copper mould wall 铜坩埚壁corrugated mould波形铸模cover mould压缝线脚covered floor mould盖箱地面铸型cylinder mould machine 圆网造纸机double-mould-broad ridging plough 双壁起垄犁draw mould薄壁模子driel mould干型drip mould滴水线脚dry sand mould干型ear mould耳模electric pole mould hanger 电杆模型吊架end mould端模Erical mould可压锭模; 挤压锭模evacuated mould空腔模face mould面模fall wheat snow mould冬小麦雪霉病falling mould曲型线条female mould阴模fixed mould固定模flaskless mould无箱铸型floating-point mould浮点模型floor mould地铸模fluted mould波形模foam sponge mould泡沫胶硫化模footed mould压印底圈的模型forging mould锻模front mould前模full-mould casting process 实型铸造gang mould成组模; 成组模板garden mould园土get in the mould垫平铸型glass mould玻璃型; 玻璃铸型glass mould diode 玻璃模二极管graphite mould石墨型grass mould腐草土gray mould灰霉green mould绿霉病green mould of citrus 柑桔绿霉病ground mould地面铸型; 堆土木模gypsum mould石膏型hair mould毛霉hair mould sprout 毛霉芽half mould半型hoist for mould board carrier 模板车升降机hump mould压坯用阳模ice mould冰铸ingot mould钢锭模; 铸锭模; 铸锭型; 锭模ingot mould milling machine 钢锭模铣床ingot slab mould扁钢锭模insulating mould coating 隔热涂料integral mould整模型invested mould熔模铸型iron mould铁锈迹leaf mould叶霉; 腐叶土loam mould泥型lower mould half 下模; 凹模male mould凸模; 阳模master mould母型; 原模mismatch in mould铸型错箱mould印模; 模; 模板; 模具; 模筛样板; 模塑; 模子; 成型模具; 圆网; 造型模板; 塑模; 霉; 霉病; 霉菌; 纸型mould addition 钢锭模添加剂mould and die milling machine 模具铣床mould assembling 合箱mould assembling and closing 铸型合箱mould assembly 合型mould blower 吹型机mould board 造型板; 样板mould boardless plough 无壁犁mould buggy 钢锭模车mould case 模制壳mould clamp 卡具mould clamps 模型紧固夹mould cleaner 模具清洁剂mould closer 合箱机; 合箱装置mould coating material 钢锭模涂料mould core 模芯mould cover 腐殖质层mould cure 模塑硫化; 模型硫化mould dam aged sweet potato poisoning 黑斑甘薯中毒mould dimension 铸型尺寸mould drag 下半箱mould drying 铸型烘干mould efficiency 模塑效率mould emptier 脱模机构mould erosion 铸型冲蚀mould facing 涂料mould fitter 合箱工mould flat gauge 样板mould form 模型型腔mould fungus 霉菌mould growth test 长霉试验mould half 半型mould hardness 铸型硬度mould impression 模型内腔; 模型型腔; 模穴mould in a snap flask 无箱造型mould in the pit 地坑造型mould inoculation 型内孕育mould jacket 型套mould kernel 模芯mould life 模型寿命mould lifting 铸型起模mould lining 坩埚衬里mould loft 放样间mould loft floor 放样台mould lofter 放样工; 放样工人mould loftsman 放样工; 放样工人mould machine 模塑机mould machine of cereal seed selection 谷物选种机mould mark 模缝条痕mould matrix cathode 模制阴极mould oil 脱模油mould on end 垂直分型造型mould pig iron 型铁mould plaster 模型用石膏mould plate 模型板mould plunger 阳模mould plunger force plug 凸模mould preparation bay 钢锭模准备跨mould press 模压机mould pressing 旋压成形mould proofing 防霉mould rains 梅雨mould release 分型粉mould relese 脱模mould rollover unit 翻箱装置mould sand 型砂mould seam 模缝mould setting-and-stripping bay 钢锭模准备和脱锭跨mould shift 错箱mould shrinkage 模内收缩; 模压收缩; 脱模后的收缩mould splits 模组分mould stripping 铸型起模; 拆模mould susceptibility 感霉性mould test chamber 霉菌试验箱mould train 模组mould turnover 翻箱mould unloading 出模; 脱模; 卸模mould veining 铸型裂纹mould vibrator 模板振动器mould vulcanization 模塑硫化mould wash 脱模涂料mould wash mixer 涂料搅拌机multiple cavity mould多型腔铸型; 多巢模multiple mould多件石膏模multiple-part mould多箱铸型needle mould针模one-piece mould整体铸型open bottom mould底开式钢锭模open mould明浇铸型; 敞口铸型open sand mould明浇砂型optical instrument mould and fog auto-detector 光学仪器霉雾自动检测仪ornamental mould艺术造型pallet conveyer mould machine 滑板输送式造型机paper mould纸型paste mould衬碳模paste mould ware 衬碳模成形的制品peat mould泥炭土permanent mould永久铸型pig mould锭模plural mould operation 多模操作porous mould多孔模型positive mould阳模; 阳压模press mould压模press mould ware 模压器皿pressing mould压模process of unconventional heat treatment of mould模具非常规热处理工艺quadrant mould四开木压条real mould实模型rectal suppository mould肛门栓剂模refractory shell mould耐火材料壳型removal of the mould拆模reverse mould倒模; 倒型revesing permanent mould双面金属型ring mould瓶颈模ring-shaped mould环型铸模risk of mould发霉险roast sand mould干砂型rubber mould橡胶皮模running mould模筛样板; 模饰样板saccharifying mould糖化霉sealing of a mould铸型密封section mould型模sectional mould镶合砂型semi-automatic mould半自动模; 半自动塑模semi-chilled mould casting 半金属型铸造; 半冷模铸造semi-permanent mould半永久型; 半永久性模semiclosed top mould半封顶锭模shell mould machine 壳型造型机shiftable mould-board 可拆换的刀片sign mould符号模型single cavity mould整体铸型single mould单件模型skin dried mould面干铸型skin drying mould表干型sleeper steel mould轨枕钢模slime mould粘菌slip flask mould脱箱铸型snap flask mould活箱造型; 无箱铸型snapflask mould脱箱造型snow mould雪霉病; 雪疫病soap mould皂模sooty mould烟霉; 煤污病sooty mould of rice plant 水稻煤病sooty mould of tea 茶叶煤污病spacing mould隔膜split mould对开模stagnant mould不动模型standard steel ingot mould标准钢锭模steel mould钢锭模; 钢模steel mould for electric pole 电杆钢模stock mould定型模stripper-plate mould脱模板塑模sweeping loam mould刮泥型swell of a mould胀砂symbol mould符号模型tape of mould模型锥度thin-walled metal mould薄壁金属型thin-walled mould薄壁结晶器three-cavity mould三开箱铸型tilt-mould billet 可倾模锭坯tire recapping mould轮胎翻修硫化机tomato leaf mould番茄叶霉病top mould half 凸模two-cavity mould双型腔铸型variable-point-mould变点模型vegetable mould腐殖土verge mould山墙檐口线脚waste mould gypsum 废模石膏watch-case mould表壳式压模water mould水霉wood casting mould木质铸造模型X-mould machine 多模成型机。

模具中英文参照表模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location 耐落胶Teflon Paste 偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weldline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin 唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring 管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形warping走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary 丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate 齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag 线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume Running Mold剖面图Cross Section模具结构Mold Construction模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 模具完成日 completion date 雕刻Engrave托司 EJ.GUIDE PIN烧焊 Welding浇口 gate侧胶式 side gate潜伏式 sub gate热流道 hot runner阀浇式（大水口直接进胶）direct gate扇形式 fan gate手折式 break off gate点浇式 pin point gate单边打入子 runner insert gate搭接式浇口 tab gate隧道式澆口 tunnel gate牛角进胶 cashew gate/banana gate成型材料Injection material生产数（模具寿命）production volume二次加工second process投影面积projected area流动平衡 Equal flow coming out 锁模力 clamping force 成型机injection machine成型周期cycle time模具结构 mold construction模胚 Mold Base定位环 locating ring面板 top plate唧嘴 sprue流道 runner主流道 main runner分流道 side runnerA板 A plate导套 Bushing导柱 Leader Pin回针 Return Pin上模小镶件Cavity Sub-Insert 上模镶件Cavity Block行位Slide行位镶件Slide Insert压紧块（铲机）Jaw压条Gib后模 core小镶件Sub-Insert下模镶件Core Block下模小镶件Core Sub-Insert 料花 splay mark粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warping走水不平均Filling Uneven 走不齐Short Shot毛边 flash困气air trapping结合线 welding line熔接痕welding mark缩水 sink mark顶白 stress mark漏水Water Leakage刮花（擦伤）Galling火山口 crater液压油缸 hydraulic cylinder。

模具专业词汇中英文对照表部分机械类词汇Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control: 操纵器National Electrical Code 全国电气规程master schedule 要紧图表, 综合图表, 设计任务书, 要紧作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接Hard hat：安全帽Goggles：护目镜stockpile贮存packing list装箱单crate: 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector. 接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring操纵线路motor lead电动机引出线power wiring电力布线tender document．提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验girth weld环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly.装配erection 架设examination试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率操纵arc welding 电弧焊control cable操纵电缆操纵索normal bend 法向[法线]弯管cable glands: 电缆衬垫exfoliation剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture照明器材junction box 分线箱race way 电缆管道terminal box接线盒distribution board配电盘, 配电屏receptacle 插座tumble switch.翻转开关,拨动式开关cathodic protection system 阴极保护系统Circuit breaker断路开关amplifier panel 放大器盘control console 操纵台electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫TIG：Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod焊条tensile strength 抗张强度shield gas 保护气体shield jig保护夹具high frequency generator.高频发电机welding rod 焊条filler metal 焊料, 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验, qualification: 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：操纵台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面tee 三通管丁字钢T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量tack welding 平头焊接sputter 喷溅scale 废料lateral translation侧向平移weld joint 焊缝, 焊接接头plug.塞fusion 熔融base material基底材料lead foil 铅箔intensifying screen 增光屏, 光增强屏pressure test.压力试验film density.影片密度line number行数leak test漏泄试验plate thickness 筛板厚度restoration修理field fabricated 工地制造的,现场装配的junction box.接线盒flow sheet 流程图vent 放气孔, 通风孔drain 排水管instrument air仪表气源blind挡板pipe arrangement 管配置civil engineer.土木工程师bus duct 母线槽substation分站flow instrument 流量计power distribution panel 配电盘level instrument 位面计, 水平仪pressure instrument 压力仪表/压力计level switch (信号)电平开关,gage glass 液位玻璃管pilot tube指示灯line check 小检修recalibration.复校,重新校准blinding plate盲板expansion joint 伸缩接头hydrostatic pressure test静水压试验pneumatic pressure 气压scaffolding脚手架check valve止回阀liquid penetrant examination液体渗透探伤test pump试验泵witnessed inspections 现场检测hanger吊架control valve操纵阀,fabrication drawing 制造图纸,制作图schedule number表示管壁厚度系列的号码hydrostatic test .流体静力学试验,水压试验design pressure 设计压力disposition notice 处罚通知书pipe stanchion 管支柱bellow type 波纹管式expansion joint 伸缩接头vibration stopper：减震器subcontractor 转包商WPS Works Process Specification 典型工艺规程piping.管道系统flange.凸缘,sleeve 套筒ferritic .铁素体的identification mark 识别标志stencil.模绘片版,镂花模板stamping .冲压silicone paint硅树脂油漆weld bead 焊缝automatic temperature recorder 温度自动记录器penetrameter 透度计film viewer底片观察用光源civil works土建工程，建筑工程lump sum price 混合价格,统包价格scrap material废料caulking metal填隙合金[金属](材料) application drawing操作图, 应用图cable routing电缆路由选择channel bases沟渠基底vertical panel竖直面板local panel 现场配电盘power distribution panel 配电盘gauge board样板, 模板规准尺anchor bolt 锚定螺栓expansion bolt 伸缩栓, 扩开螺栓field instrument.携带式仪表instrument rack 计测器支架,计测器框架tank gauge 油箱液位计guide wire 尺度[定距]索,准绳name plate名牌, 商标lead pipe铅管take-off valve输出阀sub-header分联箱air header 集气管pneumatic signal气动信号steam trace 加热蒸汽管道electric heat tracing.电伴随加热cable trunk 电缆管道stop end封端fire barriers防火间隔bonding wire 接合线, 焊线conduit box [电]导管分线匣刚性导管rigid conduitsflexible conduit软管conduit entry 导管引入装置平交道口管道组road crossing duct bank Capping ends顶盖末端电缆铠装cable armor电缆包皮层Cable sheathsealing compound电缆膏coaxial cable同轴电缆loop test环路测试sequence test.联锁顺序试验lintel beam 水平横楣梁flash plate闪熔镀层anchor bolt 地脚螺栓expansion bolt伸缩栓, 扩开螺栓shim plate 垫板push button station按钮式操纵站logic diagram逻辑图calculation sheet计算书flow instrument流量计level instrument 位面计, 水平仪layout drawing 布置图tie band捆扎用带材加热室Heating boxes切孔cutting openingcontrol valve actuator 阀控传动机构air set空气中凝固, 常温自硬自然硬化solenoid valve.螺线管阀,电磁阀calorimeter热量计odometer历程标tachometer转速计chronometer精密计时表单价unit price工日合计Man-day total/work-day total 人工费cost of labor材料费materials expenses机械的mechanical检查接线connection test发电机generator调相机phase regulator周波cycle减负荷装置load-shedding equipment 断路器柜circuit breaker cabinet单母线single busbar互感器transformer每相电流Current by Phase封闭式插接close type socket joint发电机操纵面板generator control panel分级卸载sorted unloading同步操纵synchronization control调速器speed governor信号屏signal screen继电器relay高压柜high pressure cabinet油浸电力变压器oil-immersed power transformer空气断路器air circuit breaker操纵屏control panel直流馈电屏direct current feed control panel电容器electric condenser计量盘metering panel成套配电箱whole set of distribution box落地式floor model操纵开关Control switches铜芯电力电缆Copper core power cable操纵电缆actuating cable热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing万用槽钢versatile U-steel电缆托架cable bracket钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座防爆插座Explosion-proof socket接地绞线earthing twisted pair接地母线earthing bus接地极lightning conductor硬质聚氯乙烯管rigid polyvinyl chloride pipe航空集散站air terminal水银灯具Mercury Lamp金属卤化物灯metal halide lamp高压钠灯High Pressure Sodium Lamp额定电压Rated Voltage额定功率Rated Power光源Light Source防护等级Grade of Protection高压汞灯High Pressure Mercury Lamp高压钠灯High Pressure Sodium Lamp金属卤化物灯Metallic Halide Lamp照明电缆lighting cable单线mongline穿线threading接地跨接线earthing jumper分线箱junction box接线盒connection box圆钢round steel扁钢flat steel插座socket配电盘switchboard转换开关alternation switch自动指令呼叫装置automatic instruction calling device扬声器loudspeaker明装Unfold Install暗装Conceal Install感温探测器Thermal Detector恒温·干燥器/恒温恒湿器Drying Ovens/Humidity Chambers---(在重庆有OEM生产)送风定温恒温器Forced Convection Constant Temperature Ovens惰性气体恒温器Inert Gas Ovens精密恒温器Precision Constant Temperature Ovens洁净恒温器Clean Ovens送风定温干燥器Forced Convection Constant Temperature Drying Ovens空气幕送风定温恒温器Forced Convection Ovens With Air Curtain定温干燥箱Constant Temperature Drying Ovens角形真空定温干燥器Vacuum Drying Ovens恒温恒湿器Constant Temperature and Humidity Chambers流水线设备In-Line System for Underfill Adhesive and Encapsulation恒温培养器Constant Temperature Incubators---可程式低温培养器Low Temperature Program Type Incubators低温培养器Low Temperature Incubators低温稳固性培养器Low Temperature Stability Incubators培养器IncubatorsCO2培养器CO2 Incubators振荡培养器Shaking Incubators冻结干燥器Freeze Dryers---冻结干燥器Freeze Dryers离心形冻结干燥器Centrifugal Freeze Dryers灭菌器Sterilizers---干热灭菌器Drying Sterilizers高压灭菌器Autoclaves Sterilizers低温等离子灭菌器Low Temperature Plasma Sterilizers环形燃烧管灭菌器Loop Cinerator纯水制造装置Water Purifiers---纯水制造装置Water Stills超纯水制造装置Ultra-pure Water Purifiers简易纯水制造装置Water Purifiers超纯水制造装置系统Ultra-pure Water Purifier System大容量纯水制造装置Water Purifiers System洗净器Washers---实验室玻璃器皿清洗机Laboratory Glassware Washers超声波清洗机Ultrasonic Cleaners大型超声波清洗机Aqueous Ultrasonic Cleaning Systems超声波试管清洗机Ultrasonic Pipet Washers超声波清洗机Ultrasonic Cleaners恒温液槽Constant Temperature Baths---投入式恒温装置Constant Temperature Devices油槽Oil Baths振荡式低温水槽Low Constant Temperature Shaking Baths 深槽形恒温水槽Constant Temperature Water Baths粘度测定槽Kinematic Viscosity Baths液压式恒温水槽Constant Temperature Water Baths精密低温恒温水槽Precision Low Constant Temperature Water Baths 低温恒温水槽Low Constant Temperature Water Baths试验管加热板Heating Blocks冷却液体循环器Cooling Liquid Circulators冷却水循环器Cooling Water Circulators便携式冷却器Immersion Cooler寒流捕获器Cooling Trap冷却水外部循环器Cooling Water Circulators试验槽Thoughs高温炉High Temperature Furnaces Heating Apparatus---马弗炉Muffle Furnaces超高温电气炉Ultra-High Temperature Electric Furnaces高温电气炉High Temperature Electric Furnaces真空气体置换炉Gas Replacement Vacuum Furnaces造粒干燥装置Granulating and Drying Apparatus for Wet Powder Body and Liquid---喷雾干燥器Spray Dryer有机溶剂喷雾干燥器Spray Dryer生产线喷雾干燥器Spray Dryer for Product Line浓缩器Evaporators---旋转蒸发仪Rotary Evaporators溶媒回收装置Solvent Recovery Unit乳化·搅拌·振荡器Homogenizers, Stirrers, Shakers---磁力搅拌器Magnetic Stirrers加热板Hot Plates振荡器Shakers送液·减压·加压装置Aspirators, Pumps, Compressors搅拌器Stirrers实验室自动乳钵Laboratory Mill/Universal Ball Mill粉碎器Cutting MillsYAMATO电子厂关连仪器Electronics Facilities Related Devices等离子装置Low Temperature Ashers, Cleaners, Etchers---气体等离子蚀刻机Gas Plasma Etcher “Plasma Reactor”气体等离子清洗机Gas Plasma Dry Cleaner气体等离子灰化机Gas Plasma Asher半导体基板自动机器Automatic Machine电子半导体/材料关连仪器Electronics Facilities Related Devices---桌上小型探测显微镜Desk-Top Small Probe Microscope “Nanopics”半导体制造用检查装置Yield Management for Semiconductor Ptoducts非破坏评价解析装置Nondestructive Testing System紫外线洗净·改质装置Ultra-Violet Curing System尘埃计数器Particle Counters风速计Anemometers去静电风机、风幕及静电测定计Auto Balanced Over Head Ion Blower环境试验设备Temperature,Humidity Testing Chamber防湿保管库Moisture-proof StorageNanotechnology半导体用设备ANELVA日本电子制品Jeol振动试验装置Vibration Test Systems冲击试验装置Shock Testing SystemsYAMATO生命科学关连仪器Life-Science Related Instruments生物技术关连仪器·食品分析仪器Bio-Technology Related Instruments, Food Analysises Instruments—形态观察分析系统Mapping Analyzer生物分子间相互作用分析系统Biomioleculer Interaction Analysis System 高速液相色谱仪LC-CE/CEC System血管壁细胞混合培养系统Dynamic Coculture System动植物破碎机基因检查仪器Genopattern AnalyzerATP测定器ATP Measuring Instrument分光光度计Microplate Spectrophotometer细胞培养·发酵用自动分析系统Automated Chemistry Analyzer for Monitoring Cell Culture and Fermentation Processes细胞生死判别系统Cell Vital Analyzer细胞计数分析装置Cell Scaler/Analyzer2元电泳仪荧光Spot Cutter高速冷却离心机High Speed Refrigerated,Centrifuges微量高速离心机High Speed micro-Centrifuges液体中微生物简单测试仪Simple Germ Test Kit “simple Tester” 试料混合器Blender防爆冷藏柜Explosion proof Freezer and Refrigerator杀菌水生成系统Sterilization Water Production Device膜式脱气装置Filter-type Air Extractor抗酸化机能水制造装置Acid-Resistant Water Purifier高性能净水器反渗透式高性能净水器分析仪器Analytical Instruments---分光光度计Spectrophotometer元素分析装置Atomic Absorption SpectrophotometerICP发光分光分析ICP Atomic Emission SpectrophotometerX线光分析计X-Ray Fluorescence Analysis气体分析计Gas Analyzers回折/散乱式粒度分布测定装置Analyzer,Particle Size Distribution Laser Diffraction Device低真空走查电子显微镜Scanning Probe Micro Scope高速液相色谱仪Liquid Chromatograph滴定装置Automatic Titration大塚电子制品电位计膜厚计散乱光光度计LCD测定·评价装置热量计天平Balances物性试验·测定器Physical Properties Measuring Apparatus, Testing, and Measuring Apparatus---近红外分析装置Fourier Transform Near Infrared Spectrometer融点测定仪Melting Point Measuring Instrument热分析系统Thermo System自动反应装置Automatic Reactor水分计Moisture Analyzer引张压缩试验机Tester,Tension and Compression数字粘度计Digital Viscometer振动式粘度计Vibro Viscometer浸透压测定装置Osmotic Pressure Meters超临界水酸化系统Small SCWO Systems重金属排液处理装置Heavy Metal Eliminator简易水质检查试验纸Water Quality Tester StripsPH计Phmeter导电率计Conductivity Meters湿度计Hygrothermometers过滤器FilterYAMATO试验研究设备Laboratory Design and Engineering---通风柜Fume Hoods排风机Blowers实验台Laboratory Furniture保管柜Storage Cabinets实验台用附属器具Carts and Laboratory Table Attachments环境制御设施Research Facilities, Product Lines, Environment control Devices---生物安全柜Biohazard Safety Equipment废水处理系统Waste Water Treatment试验动物饲养室Bio Clean Room for Animal experiment环境实验设施Research Facilities, Product Lines, Environment Experiment Facilities---电磁波室隔音室恒温室/恒温恒湿室Constant Temperature and Humidity Facilities低温室Constant Low Temperature Facilities人工气候室Artificial Atmospheric Phenomena Simulator动物研究用高压蒸汽灭菌装置Sterilization Systems, for Animal Research。