课程设计—碎纸机说明书电子版

粉碎机的设计1.粉碎机箱体设计1.1.粉碎机的的结构及其设计步骤传动装置粉碎装置粉碎轴粉碎器粉碎设备轴封罐体粉碎罐附件图1-1粉碎机结构组成示用意1.1.1.初定粉碎的3个参数的最优组合转速为60r/min，，始终存料量150kg，粉碎均匀度可达96%以上。

1.1.2. 叶轮形式选取直杆打坏形式表1-1直杆打坏卧式粉碎设备作为赤泥粉碎器桨型常用尺寸通常运转条件常用介指黏度范围流动状态直杆打碎形式d/D=0.9~0.98N=40~70r/minV<2m/s小于510mPa.s径流型。

一般是粒体沿罐壁旋转在从出口漏出。

b/D=0.1直杆条数为5~8简图：如下1.1.3.粉碎室的设计与计算（1）粉碎室的体积V的计算该赤泥粉碎机体为槽型，其截面为V型，用5mm钢板焊接而成；转子采纳直杆旋转打坏形式，转子转动使料被打坏，再从出料口漏出。

依照赤泥加工的工艺要求，一、提出粉碎机为持续出料, 且保证不中断和下级带上堵料，二、有伯努利方程：p1ρg +α1v12g+h1=p2ρg+α2v22g+h2。

因此料斗中至少要保证有V/2的料量，V/2的料量为1.5倍的赤泥板材块的量，一块板的体积V1=1.2*0.5*0.2=0.12m3有公式V=n*2*1.5*V1=0.72m3为保证料不从上面不露出取n=2。

（2）粉碎室的各部份尺寸粉碎室的各部份尺寸，包括粉碎室上端长度a（米），粉碎室上端宽度b(米)，转子中心离机壳顶部的距离h(米)，底部圆弧的半径d, V值确信后，计算a,b,h,d 各值，使之知足V值的要求。

V=f(a,b,h,d)，而a,b,h,d均为未知数，故需在这四个数中第一选定一个为主参数，然后依照它们之间的彼此关系再来确信其余的三个。

咱们选定d值为要紧参数，因d值直接关系到转子直径D及转子转速n，而这两个参数又涉及到粉碎机的工艺性能。

图1-2混合室要紧尺寸令p=a/d;u=b/d;i=h/d.搅拌室由上半部的立方体V1及下半部的半圆柱体V2组成，即V=V1+V2，则 V=V1+V2={（d+b）*(h-d/2) *a}/2+（d2π∗a）/8依照现有粉碎机的统计资料说明i=h/d值转变范围较大，一样取i=1.5~3.5 取i=3。

碎纸机使用说明
碎乐碎纸机（Ceiro E310D）简易使用说明
1.插上电源。

2.启动开关，主电源开关位于机器右侧面。

3.按下运行开关，运行开关位于入纸口右侧。

4.碎纸机进入感应入纸工作状态，红外线感应装置自动启动，进行切割或停止，请勿将手靠近入纸口。

5.光盘及PVC卡使用专用粉碎入口。

6.卡纸提示灯亮，纸张放入过多，卡纸后将纸拖出，拆分后重新投入。

无法投入纸张时，按住面板启动开关处“R”键（倒退键）不放，直至卡纸退出，提示灯灭。

禁止短时间内交替按启动开关的正转反转，易导致切割器损坏。

7.满纸提示灯亮，清理收集箱。

8.过热提示灯亮，暂停使用15-20分钟。

9.禁止带胶物及各种液体置入粉碎机。

10.可碎物包括纸张、软盘、光盘、PVC卡、订书钉、回形针、硬盘、优盘。

11.本说明参照碎乐保密销毁产品说明及使用手册完成。

Shredder Series碎紙機系列Cutting System Series切紙器系列WAY TO SHRED Innovative Fellowes ShredderWhy Shred? 為何要碎紙?Nowadays there is no longer any doubtWhy Shred? 哪些資料要碎掉?Fellowes - The World's Toughest Shredders 資料保密最強助手Why Fellowes? 為何要選擇Fellowes?Fellowes affiliated brands 附屬品牌Founded in 1917 by Harry Fellowes, Fellowes products are now selling in over 100 countries- Records Storage- Mobile TechnologyAccessories文件儲存系列流動通信及科技產品Shredder Features碎紙機功能說明Shredded ShapeThe Security Level of Shredder碎紙機的保密程度Shredders are also segmented into security categories called DIN levels. The higher:S U P E R I O R2x1Extra Shredder Features 碎紙機額外功能T h e r e a r e s e v e r a l i n n o v a t i v e f e a t u r e s a v a i l a b l e o n F e l l o w e s s h r 感Pa u l a u s h i s•碎條 7mm•每次可碎 5 張紙 (70磅紙)•平均每分鐘碎紙速度 : 5 米•可碎釘書釘•碎紙口闊度 : 220毫米•11公升碎紙容量•自動起動及停機功能•回切功能•Strip shred: 7 mm•Sheet capacity: 5 sheets (70 gsm) P-20•碎粒 3.9 x 38 mm•每次可碎 5 張紙 (70磅紙)•平均每分鐘碎紙速度: 1.8 米•可碎釘書釘及信用咭•碎紙口闊度: 220毫米•12公升碎紙容量•特設安全鎖制，防止小童或寵物誤啟•自動起動及停機功能•回切功能•附設手柄，方便移動及清倒紙屑•倒廢紙時自動停機功能•過熱自動停機功能•操作時音量: 70分貝 (dB)•Cross shred 3.9 x 38 mm•Sheet capacity: 5 sheets (70 gsm)•Shredding speed: 1.8 m / min•Durable steel cutter: can shred staples and credit card•Throat Width: 220mm•Bin capacity: 12 Litres•Safety power lock•Auto start & stop function•Auto stop when load for cleaning •Reverse function•Auto stop during rubbish cleaning •Thermal overload protection•Noise level: 70 dB•Security DIN level (5 * Highest): ***•Power : 100W•Dimension :300(H) x 340(W) x 195(D) mm •Weight: 3.3 kg•1-year self-pick up warranty serviceP-35C•碎粒 3.9 x 50 mm•每次可碎 8 張紙 (70磅紙)•平均每分鐘碎紙速度: 3.6米•可碎釘書釘及信用咭•碎紙口闊度: 230毫米•18公升碎紙容量•嶄新入紙量尺設計，避免入紙過多情況•特設安全鎖制，防止小童或寵物誤啟•自動起動及停機功能•回切功能•視窗式設計，方便檢查廢紙量•倒廢紙時自動停機功能•過熱自動停機功能•操作時音量: 70分貝 (dB)P-48C•Cross shred 3.9 x 50 mm•Sheet capacity: 8 sheets (70 gsm)•Shredding speed: 3.6 m / min•Durable steel cutter: can shred staples and credit card•Throat width: 230mm•Bin capacity: 18 Litres•Sheet capacity selector eliminates jamming •Safety power lock•Auto start & stop function•Reverse function•Clear window for waste checking•Auto stop during rubbish cleaning •Thermal overload protection•Noise level: 70 dB•Security DIN level (5 * Highest): ***•Power : 218W•Dimension: 360(H) x 363(W) x 260(D) mm •Weight: 5.8 kg•1-year self-pick up warranty service8•碎粒 3.9 x 50 mm•每次可碎 9 張紙 (70磅紙)•平均每分鐘碎紙速度: 3.6米•可碎釘書釘及信用卡•碎紙口闊度: 230毫米•22公升碎紙容量•嶄新入紙量尺設計避免入紙過多情況TM •SafeSense 全球獨有專利感熱安全技術，當人手誤觸碎紙 口時，即馬上停機。

天威碎纸机说明书
天威碎纸机是一款功能强大的碎纸机,可以快速、有效地将纸张破碎成微小的碎片。

以下是使用该机器的说明书,供您参考。

1. 安装
首先,请确保已准备好天威碎纸机的所有配件,包括电源适配器、说明书和支架。

将电源适配器和支架插入电源插座,确保连接牢固。

然后将说明书阅读一遍,并按照屏幕上的说明进行操作。

2. 配置纸张
在开始使用碎纸机之前,请确保已准备好要破碎的纸张。

可以将纸张放入碎纸机的进纸器中,或者将其放置在支架上,以便可以轻松地取出。

3. 破碎纸张
一旦准备好纸张,请按下碎纸机上的“开始”按钮,或者手动将碎纸机提起并旋转到所需位置。

然后,耐心等待纸张被破碎成微小的碎片。

4. 检查碎片
一旦碎纸机工作正常,请检查生成的碎片是否合规。

可以查看说明书以了解有关合规要求的信息。

如果需要更多的指导,可以咨询天威碎纸机的客户服务中心。

5. 清理和保养
在使用完碎纸机之后,请将其放置在干燥、通风的地方,并按照说明书中的要求进行清理。

如果碎纸机工作不正常,或者出现了噪音或其他故障,请立即联系天威碎纸机的客户服务中心,以便得到帮助。

6. 延长保修
天威碎纸机提供一年保修,如果在保修期间出现故障,可以联系天威碎纸机的客户服务中心,获得帮助。

为了更好地理解如何延长保修期限,请查看天威碎纸机的说明书。

完整设计——碎纸机03版本产品简介：本产品是一台家用碎纸机，可用于将纸张等物品快速地切碎，以便于处理和储存。

该碎纸机采用全自动控制方式，能够自动启停，配备大容量碎纸箱，使用方便安全可靠。

同时，该碎纸机具有噪音低，动力强劲，效率高等特点，适用于家庭和办公场所使用。

产品特点：1. 全自动控制：碎纸机采用先进的全自动控制方式，可以在保证安全的前提下，自动启停，避免用户过度使用造成损坏。

2. 大容量碎纸箱：碎纸机配备大容量碎纸箱，可以将大量纸张一次性切碎，避免频繁清理次数，增加操作效率。

3. 噪音低：碎纸机采用降噪隔音技术，噪音低至60分贝以下，使用时对周围环境的干扰很小。

4. 动力强劲：碎纸机内部采用高效电机，驱动切割刀具，功率大，能够处理较多的切削物。

5. 安全可靠：碎纸机采用多重安全保护措施，包括防卡滞、过载保护、自动断电等功能，确保使用时的安全可靠性。

产品参数：型号：SHJ-03电源电压：220V/50Hz电机功率：800W碎纸尺寸：5×60mm碎纸速度：3m/min碎纸容量：20L外观尺寸：360×260×490mm重量：10kg使用方法：1. 将碎纸机放置在平稳的地面上，插好电源插头，打开电源开关。

2. 将需要处理的纸张等物品放入进料口，推进到切割刀具处。

3. 碎纸机会自动感应纸张，启动切割刀具，将纸张切割成5×60mm的碎片放入碎纸箱中。

4. 当碎纸箱快满时，拔出碎纸箱，倾倒掉里面的碎纸，再插回碎纸机中，即可继续使用。

注意事项：1. 碎纸机使用时请勿将手伸入进料口，以免造成伤害。

2. 碎纸机使用过程中请注意避免将过大过硬的物品放入进料口，以免卡住切割刀具。

3. 如发现碎纸机异常情况，请关闭电源并联系售后服务中心进行维修。

4. 每次使用后请清理碎纸机，以免纸张碎屑残留在内部影响下次使用。

售后服务：本产品提供一年免费质保服务，质保期内如发现非人为损坏情况，可免费更换或维修设备。

机械原理课程设计说明书题目：破碎机的设计新疆大学《机械原理课程设计》任务书班级: 机械10-2设计说明书一份(主要包括:运动方案设计、方案的决策与尺度综合、必要的机构运动分析和相关的机构运动简图)发题日期: 2013 年 6 月 27 日完成日期: 2013 年 7 月 12 日指导教师: 哈丽毕努目录前言第一章设计题目-破碎机 ------------------------------71.1方案一 -----------------------------------------71.2方案二 -----------------------------------------81.3方案三 ---------------------------------------10 第二章第二章设计方案的拟定--------------------------132.1设计条件和要求---------------------------------132.2原始数据即设计要求--------------------------132.3.设计任务-----------------------------------142.4结构造型------------------------------------142.5.机械系统运动方案的拟定与比较---------------15 2.6 所选机构的运动分析与设计-------------------16 参考文献 --------------------------------------------18心得体会 --------------------------------------------19前言破碎机械是对固体物料施加机械力，克服物料的内聚力，使之碎裂成小块物料的设备。

破碎机械所施加的机械力，可以挤压力、劈裂力、弯曲力、剪切力、冲击力等，在一般机械中大多是两种或两种以上机械力的综合。

2012年机械原理课程设计碎纸机设计者:学号：100800622 姓名：邱凯凯学号：100800620 姓名:赵海博学号:100800627 姓名：龚国强指导老师:周申华2012年6月21日~7月5日目录一设计题目二设计任务三机器的功能分析四碎纸机的发展五运动方案设计六运动方案的评价及选定七机器的运动循环图八执行机构的设计与分析九工作中常见的问题及解决办法十碎纸机的使用注意事项及保养十一设计小结十二参考资料一设计题目设计一台能制动粉碎纸张的粉碎机.操作者将一叠规格相同的待粉碎的纸张放入碎纸机的集纸器，合上盖子，按下按钮，碎纸机激动将纸张送入碎纸槽内粉碎,当槽内纸屑堆积到一定量时予以清除。

自动碎纸机保证纸张一旦送入机器后,在被粉碎完毕之前无法开盖取出，以免文件泄露。

碎纸机的只要工艺动作为：（1）将纸张逐张送入碎纸槽。

（2）锁紧集纸器盖子。

（3）将纸张粉碎。

（4）定时清除纸屑。

原始数据如下：（1）碎纸生产率为90张/min。

（2）电动机转速为2800r/min。

（3）机器总体尺寸不大于600mm*400mm*1000mm。

二设计任务（1）拟定工艺原理图和运动循环图。

（2）进行送纸，碎纸，清除纸屑,集纸器盖子启闭的的执行机构选型.（3）进行执行机构的组合方案评定和选型，画出执行机构组合方案示意图。

（4）拟定传动系统并确定其传动比。

（5）画出包括执行机构和传动系统的机械运动方案示意图。

（6）对传动系统和执行机构进行尺度综合，按比例在图纸（A2或A3）上画出机械运动方案简图。

（7）对主要执行机构运动分析，画出从动件运动线图.（8）对碎纸机进行三围造型和运动仿真。

（9）编写设计计算说明书。

三机器的功能分析碎纸机是由一组旋转的刀具、纸梳、驱动马达、制锁装置、定时清理装置和减速齿轮组成的.纸张从相互咬合的刀刃中间送入,被分割成很多的细小纸片，以达到保密的目的。

碎纸机到现在为止经历了六代的发展历程，由最初的带传动、塑料齿轮、链传动到现在的金属齿轮传动、优质合金齿轮传动，功能也由最初的只能碎纸到现在的不仅可以碎纸，同时也可以碎光盘、回形针等硬质用品，碎纸机作为一种保密设备，已逐渐成为办公室内不可缺少的一种简易装置,这不仅是因为它具有保密功能,更是因为它可以为现代办公提供一份环保清洁的保证.（1）马达：提供动力装置。

P r i n t e d i n G e r m a n y • I D E A L 11/1999 • DAktenvernichter IDEAL 8220Aktenvernichter IDEAL 2600/2601Aktenvernichter IDEAL 3802Aktenvernichter IDEAL 3102Aktenvernichter IDEAL 4000/4003/4004Hebelschneider IDEAL 1038/1058Hebelschneider IDEAL 1033Hebelschneider IDEAL 1080/1110Stapelschneider IDEAL 3915-95Aktenvernichter IDEAL 4006 CC Aktenvernichter IDEAL 4605 Aktenvernichter IDEAL 4107Aktenvernichter IDEAL 2250Aktenvernichter IDEAL 2400Aktenvernichter IDEAL 2401/2402Not-Aus-VorrichtungInterruttore di emergenzaParo de emergenciaIDEAL 4605IDEAL 4605-Cross/CutBelangrijk:Haal de stekker uit het stopcontact voor u de machine opent!IDEAL 4605 • IDEAL 4605-Cross/Cut (a)(b)(c)(d)(e)!IDEAL 4605 • IDEAL 4605-Cross/CutMindestens einmal jährlich sind folgende !Abschaltfunktionen zu prüfen undAufzeichnungen darüber zu führen:➜Abschaltfunktion des Hauptschalters C➜Abschaltfunktion der Not-Aus-Taste B➜Vorwärts-, Stop-, Rückwärtsschaltung➜Abschaltfunktion bei geöffnetem Auf-satztrichter D➜Abschaltfunktion bei geöffneter Tür HNetzkabel und Abdeckungen müssen ord-nungsgemäß befestigt und unbeschädigtsein.At least once a year the following cut offfunction must be checked.Records ofthese inspections need to be maintained.➜Cut off function of the main switch C➜Cut off function of the emergency stopkey B➜Forward, stop, reverse switching➜Cut off function when feeding hopperis open D➜Cut off function if door H is openedPower cord and housing must be secureand undamaged.(Plastiksäcke sind vom Hersteller lieferbar - siehe Zubehör).Wird zuviel Papier zugeführt, schaltet die Maschine ab und reversiert, um den Papierstapel zu lösen.Zur Beseitigung des Papierstaus kann der Aufsatztrichter D geöffnet werden - die Maschine ist dann aus Sicherheitsgründen abgeschal-tet und es leuchtet die rote Leuchtanzeige für ‘Türe/Aufsatztrichter geöffnet’3.WICHTIG:Vor der Entnahme des gefüllten Plastiksacks, Schnittgutwagen einige Male ca.15 cm herausziehen (siehe Abbildung)IMPORTANT:Before removing the full plastic bag, shake the waste bin back and forward a few times by pulling the waste bin approx.15cm out (see illustration).IMPORTANT:Avant de sortir le sac plastique plein, secouer plusieurs fois le chariot àdéchets d’avant en arrière, en veillant à ne pas le sortir de son logement de plus de 15cm environ (voir illustration).Wolfgang Priester -General Manager-。

2012年机械原理课程设计碎纸机设计者：学号：学号：学号：指导老师：2012年6月21日~7月5日目录一设计题目二设计任务三机器的功能分析四碎纸机的发展五运动方案设计六运动方案的评价及选定七机器的运动循环图八执行机构的设计与分析九工作中常见的问题及解决办法十碎纸机的使用注意事项及保养十一设计小结十二参考资料一设计题目设计一台能制动粉碎纸张的粉碎机。

操作者将一叠规格相同的待粉碎的纸张放入碎纸机的集纸器，合上盖子，按下按钮，碎纸机激动将纸张送入碎纸槽内粉碎，当槽内纸屑堆积到一定量时予以清除。

自动碎纸机保证纸张一旦送入机器后，在被粉碎完毕之前无法开盖取出，以免文件泄露。

碎纸机的只要工艺动作为：（1）将纸张逐张送入碎纸槽。

（2）锁紧集纸器盖子。

（3）将纸张粉碎。

（4）定时清除纸屑。

原始数据如下：（1）碎纸生产率为90张/min。

（2）电动机转速为2800r/min。

（3）机器总体尺寸不大于600mm*400mm*1000mm。

二设计任务（1）拟定工艺原理图和运动循环图。

（2）进行送纸，碎纸，清除纸屑，集纸器盖子启闭的的执行机构选型。

（3）进行执行机构的组合方案评定和选型，画出执行机构组合方案示意图。

（4）拟定传动系统并确定其传动比。

（5）画出包括执行机构和传动系统的机械运动方案示意图。

（6）对传动系统和执行机构进行尺度综合，按比例在图纸（A2或A3）上画出机械运动方案简图。

（7）对主要执行机构运动分析，画出从动件运动线图。

（8）对碎纸机进行三围造型和运动仿真。

（9）编写设计计算说明书。

三机器的功能分析碎纸机是由一组旋转的刀具、纸梳、驱动马达、制锁装置、定时清理装置和减速齿轮组成的。

纸张从相互咬合的刀刃中间送入，被分割成很多的细小纸片，以达到保密的目的。

碎纸机到现在为止经历了六代的发展历程，由最初的带传动、塑料齿轮、链传动到现在的金属齿轮传动、优质合金齿轮传动，功能也由最初的只能碎纸到现在的不仅可以碎纸，同时也可以碎光盘、回形针等硬质用品，碎纸机作为一种保密设备，已逐渐成为办公室内不可缺少的一种简易装置，这不仅是因为它具有保密功能，更是因为它可以为现代办公提供一份环保清洁的保证。

Instruction ManualREV 07/26/19Electric Wood Chipper/Shredder3190553WARNING:Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.Save these instructions in a safe place and on hand so that they can be read when required.Keep these instructions to assist in future servicing.IMPORTANT SAFEGUARDSFor your own safety, always follow these basic precautions when using this appliance.1. Read the user Manual carefully for operating instructions. Read all instruc-tions in this manual before use.2. DO NOT use this product for anything other than its intended purpose.3. DO NOT use attachments other than those available from the manufacturer.4. DO NOT alter this product in any manner; doing so is dangerous and will void all warranties.5. DO NOT allow children or adults weighing under 100 lbs. to operate this unit.6. DO NOT operate under the influence of drugs or alcohol.7. DO NOT continue to use this product in the event of mechanical or electrical failure.TECHNICAL DETAILSWARNING SYMBOLS AND DEFINITIONSThis is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.DANGER Indicates a hazardous situation which, if not avoided, will result indeath or serious injury.WARNING Indicates a hazardous situation which, if not avoided, could result indeath or serious injury.CAUTI0N Indicates a hazardous situation which, if not avoided, could result inminor or moderate injury.NOTICE/CAUTION Addresses practices not related to personal injury.IMPORTANT SAFETY INSTRUCTIONSWARNING When using electric gardening appliances, basic safety precautionsshould always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:READ ALL INSTRUCTIONS Power Cord SafetyWARNING To reduce the risk of electric shock, use only with an extension cordintended for outdoor use, such as an extension cord of cord type SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.1. Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the gardening appliance. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.2. Do not Abuse Cord - Do not carry appliance by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.3. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way. This design is referred to as double-insulated, indicated by4. WARNING: The cord of this product contains lead, a chemical known to the State ofCalifornia to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.)E1Electrical Rating Blade Speed Blade DiameterMaximum Limb Capacity120VAC / 60Hz / 15A 4,100 RPM 7"1.57" Diameter5. Extension Cord - Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating.Extension Cord SizeThe following table shows the correct cord size to use depending on cord length andnameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.Connecting CordsTo reduce the risk of the cords pulling apart during operation, do one of the following:a. Make a knot as shown below then connect the cords:b. Or, use a plug-receptacle retaining strap or connector designed to hold extension cords to appliance cords.Personal Safety1. Dress Properly - Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.2. Wear ANSI-approved safety goggles and heavy-duty work gloves. Use face or dust mask if operation is dusty.3. Avoid Unintentional Starting - Do not carry plugged-in appliance with finger on switch. Be sure switch is off when plugging in.4. Do not Overreach - Keep proper footing and balance at all times.5. Stay Alert - Watch what you are doing. Use common sense. Do not operate appliance when you are tired.6. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should:• Avoid operating alone.• Don’t use with power switch locked on.• Properly maintain and inspect to avoid electrical shock.• Any power cord must be properly grounded. Ground Fault Circuit Interrupter (GFCI)should also be implemented – it prevents sustained electrical shock.E20 – 66 – 1010 – 1212 – 16EXTENSION CORD LENGTH25'1818161450'16161612100'161414150'141212TABLE A – MINIMUM WIRE GAUGE FOREXTENSION CORDS (120 VOLT)Not recommendedAmpere Rating (at full load)Extension CordAppliance Cord12Gardening Appliance Use and Care1. Avoid Dangerous Environment - Do not use appliances in damp or wet locations.2. Do not use in rain.3. Keep Children Away - All visitors should be kept at a distance from work area.4. When servicing use only identical replacement parts.5. Before Starting the Chipper/Shredder, make sure that the hopper inlet is empty.6. Keep your face and body away from the Hopper opening.7. Stay clear of the discharge area. Keep body and hands away from the discharge chute.8. Do not put your hands into the hopper opening while the unit is running. Use the paddle to push objects into the hopper.9. Before feeding material into the shredder, remove any metal, rocks, bottles, cans or other foreign objects that may damage blades.10. Use Right Appliance - Do not use appliance for any job except that for which it is intended.11. Do not Force Appliance - It will do the job better and with less likelihood of injury at the ratefor which it was designed.12. Store Idle Appliances Indoors - When not in use, appliances should be stored indoors indry, and high or locked-up place - out of reach of children.13. Maintain Appliance With Care - Keep cutting edge sharp and clean for best performanceand to reduce the risk of injury. Follow instructions for lubricating and changing accesso-ries. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.14. Check Damaged Parts - Before further use of the appliance, a guard or other part that isdamaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts,breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by a qualifiedtechnician unless indicated elsewhere in this manual.15. Disconnect Appliance - Disconnect the appliance from the power supply when not in use,before servicing, when changing accessories such as blades, and the like.16. Keep guards in place and in working order.17. Keep blades sharp.18. Keep clear of intake and discharge chute. Use included push paddle. Unplug unit and allowit to stop before unclogging.Set Up InstructionsRead the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the beginning of this manual including all text under subheadings therein before set up or use of this product.WARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:Turn the Power Switch of the appliance to its “OFF” position and unplug theappliance from its electrical outlet before assembling or making any adjustments.Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.E3ASSEMBLY1. Slide the Axle (65) through the holeson the Lower Frame (64).2. Slide a Washer (66), a Bushing (67),a Wheel (68) and another Washer (66)onto one end of the Axle.3. Secure in place with a Pin (63).4. Repeat steps 2 and 3 on the other endof the Axle.5. Press the Wheel Covers (62) onto the Wheels, over the Pins, using a rubber mallet (sold separately) to lightly tap them in placeif needed.6. Turn the Chipper/Shredder upsidedown and slide the Lower Frameends into the slots on the Base.7. Align the holes and secure inplace with two Washers andScrews.FunctionsE4SlotsBaseLower FrameAxleFigure BFigure ABushingW asherWheel PinWheel CoverControl PanelPower Switch ResetButtonHopperLocking KnobHopperBaseControl PanelLower Frame Figure COperating InstructionsRead the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.Operation1. Before operating the Chipper/Shredder, put on ANSI-approved safety goggles and othersafety gear. Safety goggles and other safety gear are sold separately.2. If an extension cord is used, ensure that it is an outdoor type extension cord and that it is the correct design to accept this appliance’s plug.WARNING!TO PREVENT ELECTRIC SHOCK AND SERIOUS PERSONAL INJURY:The extension cord must remain secured to the appliance’s plug.Secure the extension cord by either using the knot method explained in the safetywarning section, or by using a device designed specifically for retaining theextension cord (sold separately).3. Check that the Power Switch is OFF.4. Check that the feed inlet is empty.5. Check that the Hopper is securely closed and that the Hopper Locking Knob is turned fully lockwise.Note: The Chipper/Shredder will not run if the Hopper is open, not fitted well, or the Hopper Locking Knob is loose.6. Plug the Power Cord into a 120VAC/60Hz outlet.7. Turn on the Power Switch.8. Hold branches and feed them into the hopper. Release the branches when they begin to pull into the hopper.WARNING! Keep a safe distance from the Hopper opening. Longer material canlash out when being pulled in by the blades.WARNING! Keep clear of intake and discharge chute. Use included pushpaddle. Unplug unit and allow it to stop before unclogging.CAUTION! Keep the ventilation slots clear while working to avoid overheating.9. Do not shred soft, damp material such as kitchen waste as it may clog the Chipper/ Shredder. Let damp garden waste dry for a few days before shredding.10. Remove soil and rocks from roots before inserting them into the Chipper/Shredder.11. Use the push paddle to feed leaves and other small material into the Hopper.12. Feed material into the Chipper/Shredder at therate that the machine pulls the material. Donot force material into the machine.13. Set aside a few dry branches, then feed theminto the machine when finished, to help cleanthe unit.14. Wait for all material to pass through the Chipper/ Shredder before turning the unit off.15. To prevent accidents, turn the power off, anddisconnect the power supply after use. Clean,then store the appliance indoors out ofchildren’s reach.Figure DE5Overload ProtectionThis Chipper/Shredder is equipped with an overload protection system. If the unit clogs while running, the overload protection system will shut the power off. Wait at least one minute before restarting. Press the Reset Button then turn the Power Switch on.Maintenance and ServicingProcedures not specifically explained in this manual must be performed only by a qualified technician.WARNING!TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK:Turn the Power Switch of the appliance to its “OFF” position and unplug theappliance from its electrical outlet before performing any inspection, mainte-nance, or cleaning procedures.TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.Cleaning, Maintenance1. BEFORE EACH USE, inspect the general condition of the tool. Check for:• loose hardware,• misalignment or binding of moving parts,• cracked or broken parts,• damaged cord/electrical wiring, and• any other condition that may affect its safe operation.2. AFTER USE, clean external surfaces of the appliance with clean, moist cloth.3. Replace or sharpen the Blades as needed. (See below.)4. If the motor turns but the appliance does not function, the belt may be broken. Have the belt replaced by a qualified technician.5. WARNING! If the supply cord of this appliance is damaged, it must be replaced only by a qualified service technician.Cleaning the Chipper/Shredder1. Turn the Hopper Locking Knob counterclockwise and remove the Hopper.2. Clean the cutting Blades and discharge area and remove wood sticks or objects that may clog the Blades.3. Check the Blades for damage and replace if needed.4. Return the Hopper to its upright position and tighten in place with the Locking Knob after cleaning the interior.5. Use a warm damp cloth and a soft brush toclean the exterior of the Chipper/Shredder.Do not spray water or use detergents onthe Chipper/Shredder.6. Check that the ventilation slots are clean.Replacing the BladesThe reversible Blades are attached to theCutter Head with two screws.E6Figure E BladesScrews1. Access the Blades by removing the Hopper.2. Align the slots on the Cutter Head and main body and insert a screwdriver or other metal rod (sold separately) to prevent the unit from rotating while changing the Blades.3. Unthread the two screws holding a Blade and carefully remove the Blade.4. Either reverse the Blade with the sharp edge in the cutting position, have the blade profes-sionaly sharpened/honed, or insert a new Blade.5. Secure in place with the screws. Repeat with the other Blade at the same time.E7PARTS LIST AND DIAGRAMPLEASE READ THE FOLLOWING CAREFULLYThe manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representa-tion or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufac-turer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts Thereto, or arising out of his or her installation of replacement parts thereto.E8Part No.12345678910111213141516171819202122232425262728293031323334DescriptionHopperScraps Defend BlockClamp BarScrewHopper Locking KnobSpringUp HousingFrameSwitch PinScrewPush Paddle“H” Type ScrewHexagon ScrewWasherSpring Washer 1Clamp BlockScrewBladeBlade PlateDrive BlockShaft SheathBlade Defend BlockScrewDown Housing25 Nut 1Nut Frame PlateHex NutSwitchSpring Washer 2Switch Frame PlateScrewPower CordCord SheathCord Clamp PlateQ’ty111231111171211114211111211141412111Part No.35363738394041424344454647484950515253545556575859606162636465666768DescriptionConnecting Wire 2Connecting Wire 1Power SwitchReset ButtonMotor CasingMotor CoverCapacitorFanBearingScrewMotor SupportCarbon BrushBrush BoxFieldArmatureBearingWind Defend BoardDown Cover Of Gear BoxSmall Belt WheelNutBearingEccentric WheelBig Belt WheelBeltUp Cover Of Gear BoxBearingSpannerWheel CoverPinLower FrameAxleWasherBushingWheelQ’ty1111111112122111111111111112211422E9Intradin (Shanghai) Machinery Co., Ltd.***************************E10。

办公室碎纸机操作细则
1 引⽤⽂件
WHQC26-01 《办公室⽂员操作规程》
2操作细则
2.1打开电源开关，电源指⽰灯亮，即进⼊碎纸⼯作状态。

2.2 从喂纸⼝放⼊纸张，机器⾃动进纸粉碎，当纸张全部粉碎后，机器会⾃动延时停机。

2.3如果⼀次性粉碎纸张过多，机器会停⽌进纸。

操作者应退出纸张，此时智能电路⾃动清除碎纸⼑上的纸屑，机器重新恢复正常⼯作状态。

2.4 当机器箱内的纸屑超过2/3箱时，将电源切断，提起主机，将机箱内碎纸倒去，这时安全指⽰灯亮，表⽰主机进⼊断电状态，当主机重新按放在机箱上后，机器⼜恢复正常。

2.5 机器宜放在通风处，勿安装在⾼湿、⾼温及明亮、阳光直射的地⽅。

2.6 及时清理机器内纸屑。

2.7 只能⽤中性洗涤剂及软布加少量清⽔擦洗机壳，勿⽤化学品清洗外壳，清洗时必须拔去电源插头，待完全⼲后再通电。

2.8 机器应防⽌有硬物落⼊。

2.9 随机随⽤，⽤完即切断电源，以延长使⽤寿命。

2.10 粉碎⽂件时，将回形针、订书针等⾦属物去除，以免损坏⼑具。

2.11⽆论机器是否⼯作，都不要将⼿或⾐物伸进⼊纸⼝。

2.12当电源电压较低时，要适当减少粉碎张数。

2.13粉碎透明薄纸时，要⽤⼿动进纸，⼀⾯按下开关，⼀⾯将纸送⼊进纸⼝，直⾄粉碎为⽌。

2.14长时间不使⽤，要拔掉电源插头。

2.15保持机器表⾯清洁。

2.16⽆论箱内纸屑多少，应每天做好清理。

2.17 如遇有机器异常情况，及时通知⼯程部修理，确保机器⼯作正常。

杭州望湖宾馆2001-03-28批准2001-03-28实施QD01-05/1-1。