HMO3000 SeriesMixed Signal Oscilloscopes 300/400/500 MHz BandwidthT e s t & M e a s u r e m e n tP r o d u c t B r o c h u r e | 01.10Intelligent user interfaceTo optimize the screend isplay the instrument shows and hides menusPrecise signal analysis4 Gsamples/s sampling rate 8 Msamples memorySetupIntuitive, multi-lingual user menuFFTSuperb FFT functionalityHelpContext-sensitive helpQuick viewAt the push of a button the 16 most important values of the measured signal are permanently updated and displayedFanMaximum noise reduction by temperature-controlled fanZoomMemory zoom up to 250,000 : 1Analog channelsVertical sensitivity of up to 1 mV/div.Bus signal sourceTo create SPI, I 2C, UART and counter signalsAlways with MSO functionalityAnalyze analog channels plus up to an additional 16 digital channelsMathWide range of programmable math functionsSerial Bus AnalysisHardware-based triggering and decoding (optional)2 HMO3000 SERIES2014Product of the YearHMO3000Winner in category Test & MeasurementAt a glanceThe 2- and 4-channel instruments provide bandwidths of 300, 400 and 500 MHz, a sampling rate of 4 GSa/s and a memory depth of 8 MPts. The instrumentsare rounded off with a standard inclusion of the MSO functionality and several options for serial bus analysis to meet all requirements of modern development designs.HAMEG Instruments is offering the new HMO3000 series exclusively as amixed-signal oscilloscope. It is also unnecessary to initially activate the mixed-signal functions via software options, as is the case with other suppliers. The low capacitance logic probes HO3508 (also available as double pack HO3516) are optional. They allow the analysis of up to 16 logic channels with a sampling rate of 1 GSa/s. HAMEG logic probes are not linked to a specific instrument serial number. This allows their use with all digital HAMEG oscilloscope of the HMO series.For communications between embedded systems and the environment the HMO3000 includes hardware-based signal triggering and decoding for all common protocols (I2C, SPI, UART, CAN and LIN). This option can be activated with an upgrade voucher at any time.The integrated three-digit digital voltmeter enables service technicians to simultaneously perform voltage measurements on all analog channels with four values totalling. The segmented memory option HOO14 enables you to divide the available memory of your HMO3000 into up to 1000 segments. This procedure allows sampling rates of 200,000 Wfm/s, which makes it possible to capture rare anomalies occurring during many short events in quick succession. For the analysis of the recorded signals, all measurement functions of the HMO are available, including the Pass/Fail function.Thanks to the FFT analysis function with 64 K test points the HMO3000 series keeps pace with significantly larger oscilloscopes also in the frequency domain. The time domain signal, measurement window, FFT analysis result are displayed together on a single screen, which makes it easier to evaluate the input waveform.The HMO3000 series offers time domain, logic, protocol and frequency analysis in a single instrument and is a member of the Rohde & Schwarz family of scope-of-the-art oscilloscopes.Systems that are constantly becoming faster and more complex lead to everhigher demands on the required measurement technology. The new HAMEGoscilloscope series HMO3000 offers the solution for current requirements inregards to bandwidth, sampling rate and memory depth. Its bandwidth of upto 500MHz allows HAMEG Instruments to set a new milestone in the develop-ment of high-performance mixed-signal oscilloscopes at an attractive price.More information | 3500 MHz400 MHz 300 MHz 4 channel HMO3054HMO3044HMO30342 channelHMO3052HMO3042HMO30324 HMO3000 SERIESKey factsSuperior hardware-based acquisition for precise measurement results ❙4 Gsample/s sampling rate, 8 Msample memory depth ❙High vertical sensitivity down to 1 mV/div❙Low-noise measurement due to state-of-the-art A/D converter ❙High acquisition rate to identify signal faults❙Segmented memory and manually adjustable memory depthVersatile measurement functions and fast results ❙Wide selection of automatic measurement functions ❙QuickView: key results at the push of a button❙Mask test: a new mask can be easily created with just a few keystrokes ❙FFT: the easy way to analyze the signal spectrum Logic analysis with the MSO option ❙Mixed signal function as standard ❙Precise triggering on signal events❙Straightforward display of digital signals❙Low test point loading due to active probe solutionSerial bus analysis: hardware-based triggering and decoding ❙Versatile trigger options for isolating specific data packets ❙Color-coded display of decoded bus signals❙Direct export of analyzed data to USB memory drive ❙Simultaneous decoding of two buses in realtimeVoltmeter measurements using an oscilloscope ❙Three-digit display for precise voltage measurements❙Simultaneous measurement on all analog channels of up to four voltage values totalling Future-ready investment and scalability ❙Free firmware updates❙Bandwidth upgrades as required❙Serial bus analysis and segmented memory via optional software licensesMore information | 5300 MHz, 400 MHz, 500 MHzShould your requirements change, then so does the HMO3000, as the 300 MHz models can be extended to 400 MHz and 500 MHz bandwidth via software upgrades whenever required. This is done with option upgrade vouchers available at your dealer.❙For 300 MHz to 400 MHz: HV342 (2 channel) and HV344 (4 channel) ❙For 300 MHz to 500 MHz: HV352 (2 channel) and HV354 (4 channel) ❙For 400 MHz to 500 MHz: HV452 (2 channel) and HV454 (4 channel)Vouchers for bandwidth upgrades or serial bus analysis options are available at your dealer.The individual voucher number and the serial number of the instrument to be upgraded is entered at . The customer immediately receives the respective licence key which can be loaded via USB memory drive into the instrument.Always a MSOno software option being necessary to unlock it.6 HMO3000 SERIESMore information | 7 ❙Logic probe HO3508 fits to all HMO series oscilloscopesHAMEG is offering the new HMO3000 series exclusively as a mixed-signal oscilloscope. The great advantages of these instruments are best illustrated by taking a look at how ADCs (Analog Digital Converter) or DACs (Digital Analog Converter) are integrated.These transformer modules include an analog signal on the one side and a digital signal on the other side. As shown in the image below the latency time of a DAC can be determined with one simple cursor measurement. Therefore a MSO allows developers to devote their full attention to the circuit without having to waste energy on the measurement setup.The active logic probe HO3508 (also available as double pack HO3516) is available separately and is not linked to a specific serial number of an instrument. It can be used with any HMO oscilloscope.14 bit DAC signal change8 HMO3000 SERIESSerial Bus AnalysisI 2C, SPI, CAN or LIN – in terms of interaction with the outside world for embedded systems, it is safe to say that these are the most commonly used communication protocols. The new HMO3000 series by HAMEG Instruments offers you hardware-accelerated signal triggering and decoding for all of these protocols. You can upgrade your instrument via software licence keys with those functions required to develop your application:❙HOO10/HV110: Analysis of I 2C, SPI and UART/RS-232 signals on analog and logic channels ❙HOO11/HV111: Analysis of I 2C, SPI and UART/RS-232 signals on all analog channels ❙HOO12/HV112: Analysis of CAN and LIN signals on analog and logic channelsSerial bus trigger types:❙I 2C: Start, Stop, ACK, nACK, Address/Data❙SPI: Start, End, Serial Pattern (32Bit) ❙UART/RS-232: Startbit, Frame Start, Symbol, Pattern❙LIN: Frame Start, Wake Up, Identifier, Data, Error❙CAN: Frame Start, Frame End, Identifier, Data, ErrorSPI bus signal, MISO / MOSI decodedHEX decoded CAN bus signalI 2C bus signal in zoom viewMore information | 9Segmented MemoryThe segmented memory option HOO14 enables you to divide the available acquisition memory of your HMO3000 into up to 1000 segments.This procedure allows sampling rates of 200,000 Wfm/s, which makes it possible to capture rare anomalies occurring during many short events in quick succession. For the analysis of the recorded signals, all measurement functions of the HMO are available, including the Pass/Fail function.You can upgrade to option HOO14 at any time with voucher HV114. The individual voucher number and the serial number of the instrument is entered at .10 HMO3000 SERIESDigital Voltmeter (DVM)The three-digit digital voltmeter is also a standard feature which makes the work of service technicians in particular easier. Voltage measurements can be performed simultaneously for all analog channels. Integrated into a single compact device it allows you to keep your workplace tidy.❙Perform measurements simultaneously on all analog channels, with up to four freely definable parameters totalling❙These options are available: DC, DC rms , AC rms , Crest Factor, V pp , V p+, V p- ❙You decide about the position of the values on the screenDVM on two analog channels with four measurement parametersRamp waveform measured by DVMHZ15 probe (sold separately)Frequency AnalysisDue to the outstanding FFT functionality of the HMO seriesoscilloscopes signals can also be analysed inthe frequency domain with up to 65,536 points. Additional practicaltools such as cursor measurement as well as peak-detect functions arealso available. They allow engineers to complete their analysissignificantly faster, also in the frequency domain.Easy analysis in frequency domainIn the time domain quite often the distortion of input s ignals cannot bedetected with the naked eye. For instance, an acquired sine wave signala ppears to be undistorted. Only the frequency spectrum - available withjust one push of a button - clearly displays additional harmonics thatoccur as harmonic oscillations for multiples of the basic frequency.Since FFT is also active for previously stored signals, it is possible tosubsequently analyze any sections of those signals captured in singleshot mode or stop mode with an adjustable window width.More information | 1112HMO3000 SERIESMore information | 1314 HMO3000 SERIESAccessories included:HO730 Ethernet/USB dual-interface card, Line cord, printed operating m anual, 2/4 probes (amount=number of channels), 10:1 with attenuation ID (HZ350 400/300 MHz, HZ355 500MHz), software-CDRecommended AccessoriesHO720USB-device/RS-232 d ual-interface cardHZ99Carrying case forprotection and transportHZO50AC/DC current probe 30 A, DC to 100 kHzHZ355DUUpgrade from2 x HZ350 to 2 x HZ355HZO51AC/DC current probe 100/1000 A, DC to 20 kHzHO740IEEE-488 (GPIB) interface card, galvanically isolatedHZ4619” rackmount kit, 4 RUHZO20High voltage probe 1000:1 (400 MHz, 1000 V rms )HZO301 GHz active probe (0.9 pF , 1 MΩ)HZ115Differential Probe 100:1/1000:1HZO41Active differential probe 800 MHz (10:1, 1 pF , 200 kΩ)HZO40Active differential probe 200 MHz (10:1, 3.5 pF , 1 MΩ)HO35088 channel logic probe (350 MHz, 4 pF)HAMEG Instruments GmbHIndustriestr. 6 | 63533 Mainhausen | Germany | Phone +49 (0) 6182 8000R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KGHAMEG Instruments® is a registered trademark of HAMEG Instruments GmbHTrade names are trademarks of the ownersPD 3607.0146.32 | Version 01.10 | 09/ 2014 | © HAMEG Instruments GmbHData without tolerance limits is not binding | Subject to change3607014632P D 3 6 0 7 . 0 1 4 6 . 3 2 V 0 1 . 1 0 P D P 1 e n。
