卡乐电子EcoBox用户手册 V1.2

操作手册目录---------------------------------------------------------------------------------1 1.简介-------------------------------------------------------------------------------21.1基本特性--------------------------------------------------------------------------22.硬件结构---------------------------------------------------------------------------2 2.1产品代码--------------------------------------------------------------------------3 2.2pCO主板布局-----------------------------------------------------------------------4 2.3输入/输出口说明-------------------------------------------------------------------5 3用户手操器--------------------------------------------------------------------------63.1用户手操器版本--------------------------------------------------------------------6 3.2 pCO手操器按键--------------------------------------------------------------------83.3图形显示手操器的功能和特性--------------------------------------------------------84. 安装------------------------------------------------------------------------------9 4.1１pCO主板的安装-------------------------------------------------------------------9 4.2输入接口-------------------------------------------------------------------------10 4.3输入接口-------------------------------------------------------------------------11 4.4电源-----------------------------------------------------------------------------12 4.5主板EPROM的安装------------------------------------------------------------------12 4.6手操器的安装---------------------------------------------------------------------124.7图形显示手操器中程序存储器EPROM的安装--------------------------------------------135. 安装注意事项---------------------------------------------------------------------136. pLAN局域网-----------------------------------------------------------------------13 6.１主板地址------------------------------------------------------------------------14 6.2手操器地址-----------------------------------------------------------------------15 6.3专用/共享手操器------------------------------------------------------------------15 6.4 pLAN局域网的电气连接------------------------------------------------------------15 6.5 pLAN局域网中手操器远距离安装----------------------------------------------------16 6.6 pLAN局域网的技术特性------------------------------------------------------------17 6.7 pLAN局域网的元件----------------------------------------------------------------17７选配卡----------------------------------------------------------------------------17７.１图形显示手操器的串行打印卡-----------------------------------------------------17７.2标准4×20LCD或6-LED显示手操器的串行打印卡---------------------------------------18７.3用于监控和远程维护网络的RS422串行通讯卡-----------------------------------------18７.4用于监控和远程维护网络的RS485串行通讯卡-----------------------------------------19７.5用于RS232接口的Modem接口卡------------------------------------------------------19７.6时钟卡--------------------------------------------------------------------------19７.7pLAN 局域网的地址卡-------------------------------------------------------------19７.8地址，时钟，32KbityEPROM卡------------------------------------------------------20７.9OEM加湿器管理卡-----------------------------------------------------------------20７.10选配卡的安装-------------------------------------------------------------------20 8故障原因---------------------------------------------------------------------------20 9技术参数---------------------------------------------------------------------------22 9.1, pCO主板PCOB*的技术参数---------------------------------------------------------22 9.2手操器PCOI*和PCOT*技术参数-------------------------------------------------------239.3电气参数-------------------------------------------------------------------------2310.尺寸-----------------------------------------------------------------------------24 10.1用户手操器----------------------------------------------------------------------24 10.2按键和显示窗口------------------------------------------------------------------2410.3PCOB*主板-----------------------------------------------------------------------2511.用户手操器的安装 ----------------------------------------------------------------26 11.1面板安装------------------------------------------------------------------------26 11.2墙壁安装------------------------------------------------------------------------26 12电气连接--------------------------------------------------------------------------271.简介pCO系列控制器是CAREL公司设计生产的一种可编程控制器,采用双微处理器技术;适用于空调和冷冻领域.可据用户的需要编写程序,使空调系统和冷冻设备运行在最佳的状态1.1基本特性类型: pCO有不同的版本可供选择.手操器可据用户需要个性化设计.据下面的特性,用户可从中选择· 标准或图形液晶显示(LCD);发光数码管显示(LED).· 按键的数目.· LED信号灯的数目.· 聚碳酸酯按键区贴面.可编程性:用CAREL公司的专利软件EasyTools对pCO控制器进行编程. 优点如下:·程序可以在不同的硬件中传递.开发出的应用程序能够快速、简单地传送给Macroplus(相反也是),仅需修改一下输入/输出口.·开发时间短、竞争性的价格、用户个性化的程序.·在线测试保证可靠性.如果用户决定使用EasyTools开发新的程序,用户可以得到最大的信任和独立.使用一组拥有许多不同应用功能的硬件,允许标准化;对整个单元,单个设备、单个电子元件进行功能测试、在线测试、”烤机”测试.将得到很高的可靠性串行接口:为连接监视器(RS485和RS422)和 pLAN局域网而安装应用范围:pCO可编程控制器是一种完全可编程,使用灵活方便的控制器.应用范围非常广泛,相同的硬件可以实现不同的控制;单冷或热泵系统(标准程序)屋顶机单元(标准程序)精密空调单元(标准程序)中小型空气处理单元(定制程序)低温展示柜控制(定制程序)冷库控制(定制程序)其它的应用程序可据用户的特别需求而开发。

卡乐掌握器IR33解释书一、电源：12-24Vac/dc(开关心换) 230Vac 或115-230Vac（开关心换）.别的所有型号配有最小功率模式免受电压降低的影响,装备里的电压低于某一阈值机会组会封闭,显示器以削减功率消费机组还能中断正常运行重要继电器仍得电只要电压回升至正常值内.二、继电器输出：掌握器能设置装备摆设1.2.3或4个输出,它们中很多都配有16A 的继电器.三、装配尺寸：××70.5mm 和××79mm,230Vac 电压,两大型号装配面板的尺寸都是71×29mm四、用户面板：1、紧缩机：紧缩机启动时亮,紧缩机在安然时光延时动作时闪耀2、风机：风机启动亮,风机的动作因为外部旌旗灯号或程序处于过程中而受到阻拦时闪耀3、除霜：除霜动作时亮,除霜的动作因为外部旌旗灯号或程序处于过程中而受到阻拦时闪耀4、帮助加热器：防湿加湿器动作时闪耀,当所选择的帮助输出用作帮助加热器时亮5、报警：报警延时外部开关量输入报警预动作时亮,在正常运行前提下,有报警事宜闪耀（高/低温或立刻报警事宜或外部开关量输入延时）6、时钟：假如设置了一个除霜时光段则图标亮,机组启动时也会亮几秒钟,解释消失及时钟7、灯光：假如防湿功效动作闪耀选择帮助输出1,作为灯光动作时亮8、办事：有故障时闪耀如E2PROM 错误或传感器故障9、字符显示：显示规模为-50～-150,小数点显示分辩率规模为～.10、HACCP：假如HACCP 功效有用亮,有新的HACCP（报警存储在显示器上显示HA或HF）报警时闪耀11、中断轮回：中断轮回功效动作时亮,中断轮回动作因为外部旌旗灯号或程序处于过程中（紧缩机最小停机时光表）而受到阻拦时闪耀12、PRG/MUTE- 让蜂鸣器停滞鸣叫撤消报警继电器动作- 吸收主动收集地址赋值要求页面时代,假如按压这一按键超出1秒钟,就会启动地址赋值程序段（参看主动串行地址赋值程序）- 同时按压SET 键和本按键超出5 秒钟,可拜访设置F 型参数菜单设置装备摆设参数或下载参数- 装备上电时按压该键超出5 秒钟,可启动设置默认参数值程序段-同时按压和本按键能复位任何已经动作的手动复位报警（rES 信息暗示报警已经复位）,相干报警继电器撤消动作13.UP/AUX- 按压该键超出1 秒钟可让帮助输出1 动作或撤消动作- 同时按压UP/AUX 键和键超出5 秒钟,可动作或撤消动作中断轮回操纵（ccbt ccE 分别暗示中断轮回开端和停滞）- 同时按压SET 和UP/AUX 键超出1 秒钟,显示用于HACCP 相干报警的子程序段（HA.Han.HF.HFn）14.SET- 按压该键超出1 秒钟,显示或许可设置设定点- 同时按压和SET 键超出5 秒钟,可拜访用于设置C 型参数的菜单设置装备摆设- 同时按压和SET 键超出1 秒钟,显示用于HACCP 相干报警的子程序段（HA,Han,HF,HFn）- 同时按压和SET 键超出5 秒钟,启动陈述打印程序（可应用功效,治理可被履行）*留意当按压每一个按键时会发出一个简短的鸣啼声这一旌旗灯号不克不及撤消警告：应防止把装备装配如下情况中：相对湿度大于90%,无凝露;轻微的振动或敲击;中断喷射的水流下;吐露在有进击性或污染的气体情况下如硫氨气体盐雾烟雾,因为这些气领会引起腐化或氧化;高频电磁或电波干扰如在天线邻近;吐露在阳光和空气中情况温度规模变更大的前提下;在衔接掌握器时下面的警告必需要遵照;假如电源衔接不准确可轻微破坏体系;应用合适端口的电缆接头,松开母螺钉,装配好电缆接头,然后拧紧螺钉,最后用手拉一下接线,检讨是否稳固.当拧紧螺钉时,不要应用主动螺丝刀.应用螺丝刀拧紧螺钉的扭矩不克不及超出50Ncm;尽可能把传感器旌旗灯号和开关量输入电缆线与电感负载和电力负载分别开来至少3 米,防止任电磁干扰.不该该把电力电缆和传感器电缆放在统一个导线套内（包含用于统一个电气面板）.不要把传感器电缆放在电力装备邻近（接触器.回路断路器等）;尽可能地削减传感器电缆线的长度防止电缆线在电力装备邻近：应用防护等级为IP67 传感器作为停滞除霜传感器,把传感器垂直放在翅片里便于冷凝物的排放,温度调节器传感器没有极性接线时不斟酌极性.五、报警参数表：六.显示和删除HACCP报警七：拜访及修正参数保管付与参数的新值：决议储存修正参数的新值按压超出5 秒钟,退出参数设置程序.对参数所作出的所有修正,临时保管在RAM 里,正常运行不按压任何键60 秒许可参数设置终止.留意假如编程修正参数是因为时光过时而停滞,时钟参数不会复位,当进入时这些参数立刻被保管.假如装备在按压前关机则先前对所有参数的修正和临时呵护的数据全体丧掉.八：设置设定点：十.手动报警复位：十一.型号及功效描写十二.机组启动时测试显示器和按键十三.参数设置装备摆设表：。

Quick Start Guide including Auto Maker™2Package ContentsCheck your product package for the following items.• If any of the above items are damaged or missing, contact your retailer.• The illustrated items above are for reference only. Actual productspecifications may vary with different models.Set of 4 Cleanup ToolsUSB Flash DriveAxis Lubricant SmartReel™2m USB A-B CableIEC C5 Power Cable Safety Guide Warranty CardRobox®Unpacking Robox®This section explains how to safely unpack your new Robox® and get it readyfor production! Your new micro manufacturing platform has been carefully assembled and packaged at our factory to arrive with you in perfect condition. Please follow the instructions below carefully to avoid causing any damage.1. Carefully cut the tape along the top of the box, being careful not to cut toodeep, and open the box.Remove the accessories box from the side by pulling on the plastic handle.2.side.344.Remove the packing tape which is used to secure the door.5. Remove the packing tape and warranty card which are secured to the bedand the blue plastic packing clip used to secure the printhead.6. Ensure that the head and bed are free to move before proceeding. You canmove them both by hand to check.• We recommend that you keep hold of all of your packaging materials,should you need to return any parts to us.At A GlanceThis section highlights all the major features of Robox®.1Print Head8X Axis Belt2X Carriage9Tip Wipe Blade3X Axis Rails10Reel Hub Cover4Print Bed11Door Interlock Latch5Y Axis Rail12Enclosure Door6Z Axis Rail and Drive Screw13Internal Ambient Lighting7Z Carriage (Right)14Front Tray Cover5This view shows the rear connections of Robox® and the SmartReel™ location.1microSD Card Flash Storage6Pause/Resume/Eject Button2USB Type B Socket7Outlet Vents3Power Switch8Door4C5 ‘Cloverleaf’ Power Inlet9Side Cover5Robox® SmartReel™• Although there is a microSD card accessible from the back of Robox®, thiscannot be read by any other machine and is only for use as internal flashstorage - access is provided only for diagnostic/repair purposes.• Do NOT connect the USB cable until you have completed the softwareinstallation on the following page.Software InstallationThis section explains in detail how to install the AutoMaker™ software package for controlling your Robox®. The included USB card drive contains this software and an electronic version of this document, as well as some sample .stl files for you to print.These steps may vary slightly depending on your operating system, all provided screenshots and instructions are from Windows 8 for reference.1. Plug your included USB drive into anavailable USB port (drive letter may vary) - choose Open folder to view files:If this is not displayed, you can access the drive throughMy Computer.2. The contents of the drive will bedisplayed in File Explorer as shown(view mode may vary).3. Navigate to \AutoMaker Software\Windows and run the installerby double-clicking on the icon -AutoMaker-windows-installer.exe4. Select the installation language from thedropdown menu, and then click OK tocontinue.785. The installer will start, click Next > tocontinue.6. Please carefully read the LicenceAgreement and select ‘I accept the agreement’, then select Next > tocontinue.7. Please choose where you would liketo install AutoMaker™, either by typing the path directly, or by clicking the button. Click Next > to continue and accept the path and begin the installation. N.B. To facilitate future support we recommend using thedefault install location.8. Choose whether you would like toadd Shortcuts to the Start Menu or Desktop. Then click Next > and wait as AutoMaker™ is installed to your harddrive.9. Installation is complete. Tick thecheckbox if you would like to read the ‘Readme’ file after clicking Finish.9Setting Up Your Robox® AccountWhen you start AutoMaker™ for the first time, the product and customerregistration screen will be displayed, allowing you to register for product updates,support and warranty repairs. Please complete all sections before continuing.Attaching the USB CableRobox® comes supplied with a 2 metre USB Type A-Type B cable for connectingto your PC. Please connect as shown.• DO NOT connect your Robox® until you have been through the softwareinstallation steps on the previous page and started AutoMaker™.Attaching the Power Cable and Powering OnConnect the supplied AC power lead to Robox® and switch on using the rearpower switch.This will install the necessary drivers for connecting your Robox® and could takea few minutes. When correctly installed and switched on, it should appear inDevice Manager as a COM port called “Robox v1.0 (COM3)” (COM number mayvary). It should also appear on the Status Page of AutoMaker™, along with whatreel and head are installed - for more information please refer to the user manual.Loading FilamentThis section explains how to load your chosen 3D printing plastic filamentinto Robox® ready to produce your first print! It is designed to be a very simpleprocess with most functions taking place automatically.Preparing the FilamentBefore attempting to load filament, it is advisable to cut the end at a shallowangle using a knife or sharp scissors to produce a sharp tip as shown below. Thiswill allow the filament to enter the extruder and melt chamber more easily.10Feeding to the HeadSimply feed the end of the filament into one of the two extruder entranceslocated in the bottom-left of the reel storage dock. If only one extruder is installedin your machine, use the top path marked ‘1’. It is much easier to perform this operation BEFOREinstalling the reel into the dock.Once the filament reaches the extruder, you will hear the motor start; at this point continue to feed in until you feel the filament has been grabbed. Robox® will then automatically feed the material all the way to the head.Installing the ReelFinally, install the SmartReel™ into the dock, you should hear a click when itis correctly located, and it should appear as a recognised reel in AutoMaker™.Congratulations! You’re now ready to print.111Print WorkflowNow you’re ready to start manufacturing, this section leads you through the simplest workflow for producing a model from an .stl file. For information on other software features, please refer to the user manual and website.Status ScreenOn starting AutoMaker™, the status screen will be the first screen that is displayed. This screen gives you a broad overview, showing you what printers are connected and what filament is installed. From here you can unlock the door, eject filament and start a new project.To start a new project, click the Next icon in the bottom right hand corner (in the toolbar) to move to the Layout Screen.Layout ScreenThis part of AutoMaker™ is used for laying out the parts you want to print and for manipulating them (size, rotation, position). To add a new model, click the Add Model button. This will display the Select a model dialog, which will allow you to browse your computer for a model file in either .stl or .obj format. You will find some sample models on the included USB Drive under ‘3D Models’. Once you have selected a model, click Open to add to your project.You will then see your chosen model displayed on the bed. You can manipulate the view using the right mouse button:Rotate View (click and drag)Pan View (click and drag)Zoom (roll wheel)Select and manipulate modelsTo move an object around on the bed, simply select it with the left mouse button and drag it to where you’d like it to be. <Ctrl> + left mouse click will allow youto select multiple models, and <Ctrl> + <A> will select them all. If it is outside ofthe build volume or overlapping with another object, the model will turn red toindicate it cannot be printed. You can also scale and rotate models by typingvalues into the input boxes on the left hand side of the screen.121 Once you are happy with your layout, click the Next icon to proceed to the Settings Screen.Settings ScreenThis part of AutoMaker™ is used for modifying any settings relating to the print before proceeding to production, including support material, speed/quality and fill density.1Quality Setting4Fill Density 2Custom Print Profile5Support Material Setting 3Profile Summary 6Brim Width• Quality Setting This allows you to select a basic quality setting from the list of options - Draft, Normal or Fine. The final option - Custom allows you to create a new profile or to select from a previously created one. To create a new profile, click the selection box and choose Create New... - for more information on this, see the User Guide.• Profile Summary This displays a brief summary of the currently selected print settings. The information available is as follows:• Layer Height in microns (µm).• Perimeters use - which nozzle is used to print the outside surface • Infills use - which nozzle is used to print the inside fill of the object.123414 • Fill Density This setting allows you to choose how ‘solid’ you would like the finished object to be. The fill pattern can also be changed using a custom profile - for more information on this, see the User Guide.• Support Material This switch toggles the printing of support material. If you are printing a part with large overhangs, you may wish to print structures at the same time to support the object. Support settings (e.g. density and type) can also be changed when using Custom profile - for more information on this, see the User Guide.•Brim Width ‘Brim’ is a term applied to FFF (Fused Filament Fabrication) which describes a large flat area which is printed around the part to help with bed adhesion and warping. It can be easily trimmed off after printing, but may greatly increase the success rate of prints with a small surface area at the base. This number specifies the number of loops (and therefore the width) of the brim. Starting ProductionOnce you are happy with your project layout and settings, you can proceed to production by clicking the Make! button - watch as your creation appears before your eyes! AutoMaker™ will provide you with an estimated time to complete, and a progress bar which shows the percentage completed.For more information on all aspects of operation - hardware and software, please refer to the User Manual which you will find pre-loaded onto the enclosed USB drive, or to our website, shown below. Happy Manufacturing!This section contains contact information for CEL Technology Ltd. There areseparate details for Support, Sales and Feedback.SupportFor product support, we have a ticketing system available online which allowsyou to track the progress of your support request. Please sign up for an accountand submit a ticket at:SalesFor sales of accessories and consumables you can contact:*********************Or visit our website at:FeedbackPlease send all general feedback on Robox® to:**********************Distributor Contact DetailsIf you purchased your Robox® from an authorised CEL reseller - please findtheir contact details below:Please direct all support and sales enquiries here in the first instance.151© 2014 CEL Technology Ltd. All rights reserved.。

• Built-in 5 common profiles, suitable for all 1/8 Racing, select and use instantly. (e.g. Zero timing-Blinky mode, 1/8 Off-Road Racing, 1/8 On-Road Racing, 1/8 GT Racing, 1/8 Sport mode).• There are 29 built-in adjustable parameters to set various power requirements. The parameters can be imported and exported, which is convenient for drivers to communicate with and learn from each other.• Support the firmware upgrade of the ESC (The multi-function LCD programming box G2 or OTA Programmer is needed to purchase). You can enjoy the latest functions. • Support 48 degrees Boost and Turbo timing. When matching with XERUN 4268/4274 G3 motor, the Max. Speed can be promoted by 50%, easily win your rival.• Multiple function: Low voltage protection, thermal protection of the ESC, motor and capacitor.• Built-in switch mode BEC with a maximum output of 15A and voltage adjustable from 6V to 8.4V (step: 0.1V) for usage with servos & other devices require different voltages.• The built-in reverse connection protection circuit of the ESC avoid the damage to the ESC due to reverse connection.• The record function of off-line data can read the Max. Temperature and RPM of the ESC and motor by Multifunction LCD Program Box (G2) or HW Link (OTA Programmer is needed to purchase), which is convenient for driver to analyze the running of the power system.• The record function of real-time data: Open this function by connecting the ESC with HW Link (OTA Programmer is needed to purchase) and mobile App can check throttle quantity, Voltage, Current, Temperature, RPM and other data in real time, and obtain the running status of the ESC and motor.03Features04Specifications06ESC Setup01DisclaimerPlease connect the wire correctly according to the instructions and drawing:1. Motor Wiring:There is difference between connection of sensored brushless motor and sensorless brushless motor. Please according to the following wiring method: A. Connect sensored brushless motor:There is strict wiring order from the ESC to the motor, the three A/B/C ESC wires must connect to the three A/B/C motor wires correspondingly. Next, connect the ESC sensor port and the motor sensor port with the stock 6-pin sensor cable. If you don’t plug the sensor cable in, your ESC will still work in sensorless mode even if you’re using a sensored motor. Note:If the forward and backward is reverse after installing the motor, please modify “no. 1I” parameters “Motor Rotation” to change the direction. B. Sensorless Motor Wiring:Users do not need to be worried in r egards to the connectivity with the A/B/C(ESC and motor) as ther e is no polarity. You may find it necessary to swap two wir es if the motor runs in reverse.2. Receiver Wiring:Insert the throttle control flat cable of ESC into the throttle channel (i.e. THROTTLE channel) of the receiver. Since the red line in the flat cable outputs 6-8.4v voltage to the receiver and steering servo. Please do not supply additional power to the receiver, otherwise the electric adjustment may be damaged. 3. Battery Wiring:Please make sure that the (+) pole of the ESC is connected to the (+) of the battery, and the (-) pole is connected to the (-). If connect reversely, the ESC cannot start up. (Add the picture of connecting battery here.)Warning!This is an extremely powerful system. For your safety and the safety of those around you, we strongly recommend removing the pinion gear attached to the motor before calibrating and setting this system. It is also advisable to keep the wheels in the air when you turn on the ESC.1) Illustration of power on/off: Short press the ON/OFF key to turn on the ESC in the off state, and long press the ON/OFF key to turn off the ESC.2) Beep illustration when turn on the ESC: When turn on ESC under normal conditions (i.e. it is started without pressing the SET key), the motor will emit several Beeps to indicate the LiPo cells. For example, "Beep, Beep, Beep" means 3S, "Beep, Beep, Beep, Beep" means 4S.XERUN XR8 Pro G2USER MANUALBrushless Electronic Speed Controller08Trouble ShootingIn order to make one firmware applicable to all different racing conditions, there are 5 groups of preset modes in the ESC. Users are able to change the settings of the modes provided and match suitable gear ratio. Plug-and -screw. Users can change the settings as per the control feel, track, and rename the setting mode. For example, the name can be changed from “1/8 Off-Road” to “NC2020-1900” to indicate the NC2020 uses 1900KV. This can be saved for future reference as well.Here is the method of setting parameters of ESC:1) LCD programming box set the parameters: (Please refer to the instructions of LCD programming box for detailes)parameters. You can adjust the setting via “ITEM” & “VALUE” buttons, and press the “OK(R/P)” button to save new settings to your ESC.Note: Only Multifunction LCD Program Box (G2) can work with this ESC!2) Use OTA Programmer to set parameters (Please refer to instructions of OTA Programmer for details) This ESC allows OTA Programmer connecting to the computer, that is, plug the programming wire of OTA Programmer to the programming port. Then use mobile phone to install HOBBYWING HW LINK App to set parameters.3) Data checking:recorded data to the designated area when you turn off the ESC after a run. You can check those data via a multifunction LCD program box whenever necessary. Users need to switch on the ESC after connection between the program box and the ESC has been established. Long Press the “OK(R/P)” button on any “item” page, followed by pressing the “ITEM” button again multiple times. The following 5 item pages will be displayed : Mode → ESC Temperature → Motor Temperature → Min Voltage → Max RPM. Attention!Press the “VALUE+/-” button on any profile page can get you into the next/prev preset mode. Please note that improper operation will get you into other preset mode(s).Here is the method of restore factory reset:1)Restore the default values with a multifunction LCD program boxAfter connecting the program box to the ESC, continue to press the “ITEM” button on the program box until you see the “RESTORE DEFAULT” item, and press “OK(R/P)” to factory reset your ESC.2)Restore the default values with a OTA Programmer (Use HW Link mobile phone App)Connect OTA Programmer to the ESC, enter into 【Parameters 】, click “reset” to factory reset your ESC.07Explanation for LED status1. During the Start-up Process• The RED LED keeps flashing rapidly indicating the ESC doesn't detect any throttle signal or the neutral throttle value stored on your ESC may be different from the current value stored on the transmitter. • The GREEN LED flashes “N” times indicating the number of LiPo cells you have connected to the ESC.2. In Operation• The throttle trigger is at the neutral: The RED LED turns on solid and the GREEN LED dies out when the throttle trigger is in the throttle neutral zone. The RED LED will blink to meet Blinky( Zero Timing) rules if the total value of Boost Timing and Turbo timing is 0.• Forward: The RED LED dies out and the GREEN LED blinks when your vehicle runs forward. The GREEN LED turns solid when pulling the throttle trigger to the full (100%) throttle endpoint. • Brake: The RED LED dies out and the GREEN LED blinks when you brake your vehicle. The GREEN LED turns solid when pushing the throttle trigger to the full brake endpoint and setting the ”Max. Brake Force” to 100%.• Backward: The RED LED dies out, the GREEN LED blinks when you reverse your vehicle. The GREEN LED turns solid when pushing the throttle trigger to the full brake endpoint and setting the ”reverse force” to 100%.3. When Some Protection is Activated• The RED LED flashes a short, single flash and repeats “☆, ☆, ☆” indicating the low voltage cutoff protection is activated. • The GREEN LED flashes a short, single flash and repeats “☆, ☆, ☆” indicating the ESC thermal protection is activated.• The GREEN LED flashes a short, double flash and repeats “☆☆, ☆☆, ☆☆” indicating the motor thermal protection is activated.• The GREEN LEDS flash a short, single flash and repeats “☆☆☆, ☆☆☆, ☆☆☆” indicating that the load of ESC is heavy, the Over-Current protection is activated.• The GREEN LEDS flash a short, single flash and repeats “☆☆☆☆☆，☆☆☆☆☆，☆☆☆☆☆” indicating that the temperature of ESC and capacitor is too high, the thermal protection of capacitor is activated.Programming:5Factory reset6Preset modes41A: Running Mode:Option 1: Forward with BrakeRacing mode. It has only forward and brake functions. Option 2: Forward/ Reverse with BrakeThis option is known to be the “training” mode with “Forwar d/ Reverse with Brake” functions. Hobbywing has adopted the “DO UBLE-CLICK” method, that is your vehicle only brakes on the 1st time you push the thr ottle trigger forward (brake) (1st push). The motor stops when you quickly r elease the throttle trigger and then r e-push the trigger quickly (2nd push), only then the vehicle will reverse. The reverse function will not work if your car does not come to a complete stop. The vehicle only reverses after the motor stops. This method is for preventing vehicle from being accidentally reversed.Option 3: Forward and ReverseThis mode is often used by special vehicles. It adopts the “SINGLE-CLICK” method. The vehicle will reverse immediately when you push the thr ottle trigger forward (brake).1B: Max. Reverse Force:The reverse force of the value will determine its speed. For the safety of your vehicle, we recommend using a low amount.1C: Lipo Cells:We strongly recommend that you set LiPo cells manually not automatically. When set automatically, the ESC can judge as 2S or 4S. If the battery voltage is lower than 9.5V after power on the ESC, it will be judged as 2S; if the battery voltage is between 9.5V ～13.6V, it will be judged as 3S; if higher than 13.6V, it will be judged as 4S. 1D: Cutoff Voltage:The ESC will monitor the battery voltage all the time, once the voltage is lower than the threshold value, the ESC will reduce the power to 50% instantly and cutoff the power output in 40 seconds. When enters into voltage protection, the RED LED will single flash that repeats (☆, ☆, ☆, ☆…….). Please set the “Cutoff Voltage” to “Disabled” or customized protection threshold value if you are using NiMH batteries. Option 1: DisabledThe ESC does not cut the power off due to low voltage. We do not recommend using this option when you use any LiPo battery as you will irreversibly damage the product. It is suggested to set to “Disabled”(But the battery would be damaged due to overcharged) Option 2: AutoThe ESC calculates the corresponding cutoff voltage as per the number of LiPo cells it detects and the “3.3V/cell” rule. For example, if the ESC detects a 4S, the cutoff voltage protection threshold value is 3.5x4=14.0V. Option 3: CustomizedThe customized cutoff threshold is a voltage for the whole battery pack (adjustable from 5.0V to 13.6V). Please calculate the value as per the number of LiPo cells you are using. For example, when you use a 4S and you want the cutoff voltage for each cell is 3.0V, you will need to set this item to 12V （3.0*4）1E: ESC Thermal Protection:The output from the ESC will be cut off with the value you have preset. The GREEN LED flashes (☆, ☆, ☆) when the ESC temperature reaches to the preset value. The output will not resume until the ESC temperature gets down.Warning! Please do not disable this function unless you’re in a competition. Otherwise the high temperature may damage your ESC and even your motor.1F: Motor Thermal Protection:The GREEN LED flashes (☆☆, ☆☆, ☆☆) when the motor temperature reaches to the preset value. The output will not resume until the motor temperature gets down.Warning! Please do not disable this function unless you’re in a competition. Otherwise the high temperature may damage your motor and even your ESC. For non-Hobbywing motor, the ESC may get this protection activated too early/late because of the different temperature sensor inside the motor. In this case, please disable this function and monitor the motor temperature manually.1G: BEC Voltage:BEC voltage can be adjusted between 6.0-8.4V. 6.0V is applicable to common servo. If use high-voltage servo, set to higher voltage according to voltage marking of servo. Warning: The setting BEC voltage should not be higher than the max. voltage of common servo, otherwise it will damage the servo or ESC. 1H: Sensor Mode:Option 1: Full SensoredIf use XERUN 4268/74-G2/G3 motor, it can set to full sensor mode. The power system will work in the “sensored” mode at all times. The efficiency and drivability of this mode is at the highest. And Boost 、Turbo timing can be used and get erupting power. Option 2: Sensored/Sensorless HybridThis is universal driving mode of current 1:8 power system. The ESC operates the motor in sensored mode during the low-speed start-up process, followed by switching to operating the motor in the “sensorless” mode when the RPM is increased.1I: Motor Rotation:With the motor shaft faces you (the rear end of the motor is away from you), increase the throttle input, the motor (shaft) will rotate in the CCW/CW direction if the “Motor Rotation/Direction” set to “CCW/CW”. Generally, the vehicle runs forward when the motor (shaft) rotates in the CCW direction. However, some vehicles only run forward when the motor rotates in the CW direction due to the different chassis design. In that case, you only need to set the “Motor Rotation/Direction” to “CW.1J: Phase-AC Swap:If the A/C wire of ESC connect to A/C wire of motor with crossed way (A wire of ESC connects to C wire of motor, C wire of ESC connects to A wire), set this item as Enable. Warning! When #A/#B/#C wire of ESC connect to #A/#B/#C wire of motor correspondingly, do not Set to Enable. Otherwise it will damage the ESC and motor.2A: Throttle Rate Control:This item is used to control the throttle response. It can be adjustable from 1 to 30 (step: 1), the lower the throttle rate, the more the limit will be on the throttle response. A suitable rate can help driver to control his vehicle properly during the starting-up process. Generally, you can set it to a high value to have a quick throttle response if you are proficient at throttle control.2B: Throttle Curve:The throttle curve parameter reconciles the position of the throttle trigger (in throttle zone) and the actual ESC throttle output. It is linear by default and we can change it to non-linear viaadjusting the throttle curve. For example, if adjust it to +EXP , the throttle output at the early stage will be higher (than the output when the curve is linear); if it is adjusted to –EXP , the throttle output at the early stage will be lower (than the output when the curve is linear.2C: Neutral Range:As not all transmitters have the same stability at “neutral position”, please adjust this parameter as per your preference. You can adjust to a bigger value when this happens.2D: Initial Throttle Force:It also called as minimum throttle force. You can set it according to wheel tire and traction. If the ground is slippery, please set a small throttle force. 2E: Coast:The RPM of the motor will be lowered gradually when throttle is reduced. The vehicle will not reduce speed abruptly when the throttle is reduced to return to the neutral position. The bigger the value, the more the “COAST” will be felt. Example, COAST of 0 deactivates, and a COAST of 20% would be the maximum amount of COAST. The advantages of COAST:When “TURBO DELAY” is set to “INSTANT”, the Turbo Timing will be activated right after the throttle trigger is moved to the full throttle position. When other value(s) is applied, you will needto hold the throttle trigger at the full throttle position (as you set) till the Turbo Timing initiates.5C: Turbo Increase Rate (deg/0.1sec):This item is used to define the “speed” at which Turbo Timing is released when the trigger condition is met. For example, “6 degs/0.1sec” refers to the Turbo Timing of 6 degrees that will be released in 0.1 second. Both the acceleration and heat is higher when the “Turbo increase rate” is of a larger value.5D: Turbo Decrease Rate (deg/0.1sec):After the Turbo Timing is activated and the trigger condition turns to not be met (i.e. vehicle slows down at the end of the straightaway and gets into a corner, full throttle turns to partialthrottle, the trigger condition for Turbo Timing turns to be not met), if you disable all the Turbo Timing in a moment, an obvious slow-down like braking will be felt and cause the control of vehicle to become bad. If the ESC can disable the Turbo Timing at some “speed”, the slow-down will be linear and the control will be improved.Warning ！Boost Timing & Turbo Timing can effectively improve the motor efficiency; they are usually used in competitions. Please take some time to read this manual and then set these two items carefully, monitor the ESC & motor temperatures when you have a trial run and then adjust the Timing and FDR accordingly as aggressive Timings and FDR may cause your ESC or motor to be burnt.Note: Parameters 5A-5D only has function when you set the “Drive Mode” to “Full Sensored”.。

✓Projector with power cord , lens ✓Test Welcome Gobo ✓Gobo Holder✓Allen key for yoke adjustmentcontact your dealer in case of warranty issues.ECO Spot™ LED C20PC User ManualThank you for choosing an ECO Spot™ Gobo projector. This manual covers the ECO Spot C20PC .Please read this manual before installing or operating this fixture, follow the safety precautions listed below and observe all warnings.•Place your fixture at a suitable place with good air flow.•Keep flammable materials away from the fixture.•Minimum distance to flammable material = 1 ft (0.3m).•Provide a minimum clearance of 4 in (10cm) around air vents.•Use only genuine spare parts for part replacement.•Do not look directly into the lamp; it can result in eye damage.•Always unplug the unit from the power mains before any service is done.•Light fixtures should be installed and maintained only by qualified personnel with experience in lighting equipment and general electrical experience.•Disconnect the fixture from AC power before handling the fixture.•Always ground (earth) the fixture electrically.•Use only a power source that complies with local building and electrical codes and has both, overload and ground-fault protection.•Do not use the fixture if the power cable or power plug is in any way damaged,defective or wet, or if they show signs of overheating.projection size and resulting brightness at varying distances. The narrower the lens, the smaller and brighter the image will be at a given distance.•Before the initial start-up, please unpack and carefully check for damage caused during transportation.•Place your fixture at a suitable place with good air flow.•Make sure there are no flammable materials close to the lamp.•When suspending the fixture above ground level, verify that the structure can hold at least 10 times the weight of all installed devices.•Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable.•Power up the projector by pressing the power switch in the back.•Focus the projection by twisting the lens in and out until the image is well focused. When used for the first time, the lens will often need to be twisted outwards many rotations to reach the focusing point.•Re-adjust the focus if necessary.•The projector is mainly designed for wall and ceiling mounting but in many cases,it can also be placed on a table or shelf.•The yoke allows projector movement in one direction:Up/down .•Unscrew the thumbscrew and screw into gobo holder to remove.•Push the two pins of the gobo retaining ring together and pull out the retaining ring. Carefully remove the old gobo and replace it with the new gobo.•If you have a glass gobo, place the more reflective side towards the light bulb.•Replace the retaining ring and make sure it evenly pushes the gobo all the way back.•Pl ace the gobo holder in the slot and unscrew the thumb screw to lock it. Screw the thumb screw into thread in front of gobo holder so it is not lost. A djust the focus by screwing the projection lens in or out until you reach a focal point, then fine tuning focus can be down with single turns to achieve full focus.Total Length:8 - 10" - depends on lens Total Height: 5.5" (incl. yoke) Weight: 2.4lbsThe projection lens adds 0.5 to 2in (12 to 50mm) to the length.with up to 3.3mm thickness. Film Gobo Life - 2 - 5 days.Standard gobo size (E-Size):Outer Diameter (OD): 37.5mmImage Diameter (ID): 27mm (max 32mm) The recommended gobo image diameter for best focusing is up to 25mm. An image diameter of up to 32mm is possible with some yellowing and focusing weakness in the outer projection area.standard ECO Spot projection lenses.A larger focal length (f) makes a smaller projection angle and therefore a smaller but brighter image. Currently these lenses are available:•Power: 20W•Rated luminous flux: 1,800lm •Effective luminous flux: 1,000lm •Rated Bulb life 30,000h •Color Temperature 7,000k,+/-500k•Wide f=56mm, 25º•Semi-Narrow f=100mm, 15º。

冷水机组微电脑控制器操作员界面用户手册CAREL srl (ITAL Y)水冷螺杆机组（单机）上海瀚艺冷冻机械有限公司第一章系统介绍卡乐控制器机组是我公司新近开发的中小型机组，因其控制稳定，操作简单，界面友好而深受用户喜欢。

本机组控制系统共由两部分组成，主控制器为CAREL（PCO1）可编程控制器兼有模拟量模块，人机操作界面为手持操作器，整个控制系统稳定、画面友好、操作简单,其功能介绍如下：一、手持操作器面板介绍手持操作器是一种按键操作屏，由微处理器、按键和LED指示灯组成，供用户设定参数，操作方便，外观如下图：主菜单显示按键；维修显示按钮；打印显示按钮（未用）；输入输出显示按钮；时间显示按钮；温度设点显示按钮；用户菜单显示按钮，机组资料显示按钮；机组开启/停止按钮；机组报警按钮，即显示报警记录或消除故障后清除报警键；上翻页键，即在操作过程中向上翻动文本键；确认键；下翻页键，即在操作过程中向下翻动文本键。

二、控制主板端子部分介绍（扩展型）1、电源端子[G（+），G（-）]；2、250V AC，2AN慢速熔丝；3、通用模拟量输入，NTC，0/1V，0/5V，0/20MA，4/20MA；4、无源模拟量输入，NTC或开关量；5、黄色电源LED及3个LED警报指示灯；6、0/1V 模拟量输出和PWM 调节输出；7、开关量输入，24V AC/DC ；8、开关量输入，230V AC 或24VAC/DC ；9、用于5V 公制电压有源探头的参照接口，和ARIA 手持器的电源接口； 10、全部标准型手持器PCO*系统列插口，及应用程序下载用插口； 11、PLAN 局域网接用连接端口； 12、程序转载器用接口； 13、继电器开关量输出；14、选择模拟量输入类型用舱盖； 15、安装串行卡的插槽舱盖；-监视用RS485； -Modem 接口用RS232 -网关（协议转换器）； 16、安装时时钟的插槽舱盖。

注：在本端子图中，因为其中部分为扩展型输入/输出端子，在单水冷机组里面用到的只为其中的一部分。