下载文档原格式
USB2.0 Storage Enclosure kitU2EC5User’s GuideRev.1.0July 2001Contents1. Before installation (3)1-1. Package Confirmation (3)1-2. System Requirements (3)1-3. Restrictions (3)1-4. Front/Back Side Function (4)2. Setup (5)2-1. Mounting a drive (5)2-2. Connectiong a power cable and USB cable (8)2-3. Installing USB driver (8)3. Removing the U2EC5 (15)4. Disk Formatting and Partitioning Utility (16)5. Registration and Tech-support (19)Appendix (20)21. Before installation1-1. Package ConfirmationCheck package contents:•U2EC5 5 inch case•AC Cable•One USB2.0 Compliant cable(1m)•Mounting screws•Support Software CD-ROM•Installation guide(This document)•Software License AgreementNOTEIf any of these items are missing from the retail package, contact your supplier immediately.1-2. System Requirements•Windows 98SE/Windows Me/Windows 2000•PC with built-in USB port or with our add-on USB PCI board/PC card1-3. RestrictionsTo enjoy USB2.0 High-Speed performance, our add-on USB2.0 PCI board(PCIU2)/PC card(CBU2) and its EHCI driver are required. No other USB2.0 PCI boards/PC Cards or drivers are guaranteed.31-4. Front/Back Side Function[Front Side](1)Front cover[Back Side][Front Side](1)Front coverYou have to remove this cover when you mount a 5 inch drive.(2)Power LEDWhen this drive is powered, this green power LED comes on.(3)Power switchBy pushing this button, you can turn a drive on or off.[Back Side](1)Power cable inletConnect the bundled power cable.(2)FanThe fan is used to force out air in the U2EC5 to keep it cool.(3)USB portConnect the bundled USB cable to the PC.(4)Audio output(LINE OUT)If you connect a speaker with an amplifier, you can listen to sound.452. SetupTo set up the U2EC5, follow the steps:2-1. Mounting a drive(1)Release the screw at rear panel.Then, slide out the inner case by pushing back panel.(2)Slide the top cover off inner case.(3)Push the hook on front panel to release front cover if you mount a 5 inch drive. If not, you don’tneed to release it. In such a case, proceed to step (6).6(4)Set [MASTER] position in jumper setting. Then, slide a 5 inch drive such as a CD-ROM into inner case and connect IDE cable, power cable and analog audio cable(red-colored line is R ; white-colored line is L).Power cableIDE cable Set [MASTER] positionAudio cable (5)Fix the drive to inner case by screws. Then, replace the top cover and slide back the inner case intoenclosure. You have finished mounting a drive. Proceed to Chapter 2-2.(6)If you mount a 3.5 inch hard drive, set [MASTER] position in jumper setting. Then, connect IDE cable, power cable.Power cable IDE cable Set [MASTER]position (7)Fix the drive to inner case by screws. Then, replace the top cover and slide back the inner case intoenclosure. You have finished mounting a drive. Proceed to Chapter 2-2.782-2. Connectiong a power cable and USB cableConnect a power cable to an outlet. And connect the bundled USB cable to the USB port on yourPC as shown below.2-3. Installing USB driver(A)For Windows 2000, Windows Me usersTurn on the U2EC5 case. The drive will be detected and the driver will be installedautomatically. If the installation was successful, you can find the added icon in [My Computer]. The example figure below shows a CD-ROM drive is added (Drive letter depends on yoursystem).NOTE:If you are a Windows 2000 user, you must belogged on as Administrator or have adminis-trator privileges to install the driver.(B)For Windows 98SE usersa)Turn on the U2EC5 case. The following window appears. Insert the Support Software CD-ROM and.click [Next]b)Select [Search for the best driver for your device.(Recommended)] and click [Next]9c)Select the [CD-ROM drive] option and click [Next].d)Make sure RTUS2ST.INF was found and click [Next]10e)When the driver has been copied onto your system, the following window appears. Click [Finish].f)The following window appears. Click [Next].g)Select [Search for the best driver for your device.(Recommended)] and click [Next].h)Select the [CD-ROM drive] option and click [Next].i)Make sure RTUS2STS.INF was found and click [Next].j)When the driver has been copied onto your system, the following window appears. Click [Finish].If the installation was successful, you can find the added icon in [My Computer]. The example figure below shows a CD-ROM drive is added(Drive letter depends on your system).3. Removing the U2EC5(1)When you click on the removal icon on the task tray, a pop-up menu similiar to the following willappear. Select it.(OS:Windows 98SE)(2)When the message box saying [the device can now be safely removed from the system] appears,click [OK]. You can remove the U2EC5 from the PC safely.4. Disk Formatting and Partitioning UtilityWith the bundled utility, you can change file system or format a storage device. Follow the steps below to use the utility(The device information depends on a device in the U2EC5).1.Make sure the U2EC5 is connected and powered on.2.Insert the support software CD-ROM into the CD-ROM drive.3.Open [My Computer] and double click the CD-ROM drive icon. Double click the FRFMTW9X.EXEfile at the [Formatter] folder in the [Rhd-U2] folder.4.[Select the Drive] dialog will appear. Select the drive and click [Select].(NOTE)1.The drive list window shows all the devices connected to SCSI, IDE besides USB interface on yourPC.2.You can format a storage device such as a HDD, Zip, MO with this utility. But, you can’t format aCD-R, CD-RW, DVD-RAM.3.This utility runs only on Windows 98SE, Windows Me.4.If you use Windows 2000, you have to use [Disk Management] in Windows 2000. If you format anover 32GBytes HDD, you have to select [NTFS] file system. If you select [FAT32], you will fail to format the HDD.For more information, refer to Windows 2000 Help file.5.[Format Utility] dialog will appear. Select [Initialize/Format media] from the [Edit] menu.6.[Initialize/Format Media] dialog will appear. Select format type. Then, click [OK].(NOTE)You can’t do low level formatto the U2EC5. Never check this[Low level format] option.7.If you selected IBM-PC/AT FDISK Format, the message box saying [You should create partition next] will appear. Click [OK]. Then, you will see the screen shown in the step 5. Select [CreatePartition] from the [Edit] menu. [Create Partition] dialog will appear as shown to the right.Select File System from the list box and set Partition size, using the slider bar.If you format the drive, check the [Format Drive] option.Then, click [OK] to create partition. If you selected Super FD format, select File System from the list box and click [OK].8.The confirmation message box will appear. Click [OK].9.The dialog shown in the step 5 will appear. Select [Quit] from the [Edit] menu. The message box will appear. Click [OK].Then, remove the U2EC5 and reconnect it for your information to take effect. (See Chapter 3 for how to remove the U2EC5).5. Registration and Tech-support5-1. How to RegisterWe highly recommend to register yourself as our customerthrough our on-line registration.(1)On the Internet, access our site. (/english/)(2)Follow window menu guide to register.(3)Fill out and submit the registration form.5-2. Software Update and Support-Software Update-The latest driver and application software are subject to change for improvement or bug fix. You can download the latest version from our web site.(/english/)-Technical Support-You can reach our Tech support staff at the following:RATOC Systems International,Inc. Tech Support(Open : Mon - Fri 9:30AM - 5:00PM PST)Address : 1933 O’Toole Avenue Suite A109, SanJose, CA 95131, U.S.A.Phone : (408)955-9400Fax : (408)955-9402E-mail:************************.jpWeb : /english/AppendixCopyright©2001 RATOC Systems,Inc. All rights reserved. No part of this publication may be reproduced,stored in a retrieval system, or transmitted in any form or by any means(electronic, mechanical, photo-copying, recording or otherwise) without the prior written consent of RATOC Systems,Inc.Trademarks-Windows is a registered trademark of Microsoft Corporation.-Other brand and product names may be registered trademarks or trademarks of their respectiveholders.ChangesThe information in this User’s Manual is furnished for information only and is subject to changewithout notice.RATOC Systems,Inc. reserves the right to make changes in the product design orproduct improvements without reservations and without notification to its users. RATOCSystems,Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, which canbe determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:(1) Reorient or relocate the receiving antenna.(2) Increase the separation between the equipment and receiver.(3) Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.(4) Consult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance may result inthis unit not complying with FCC Rules Part 15.。
ETRX2USB and ETRX2USB-PA USB STICKPRODUCT MANUALTelegesis™ is a trademark of Silicon Laboratories Inc.N o tRe co m m e nd edf or N e wDe si gnTable of Contents1 INTRODUCTION ................................................................................................................. 3 1.1 Supported Operating Systems .. (3)2 ABSOLUTE MAXIMUM RATINGS ..................................................................................... 3 3 OPERATING CONDITIONS (4)4 OTHER DATA ..................................................................................................................... 4 5 ETRX2 I/O CONNECTIVITY .. (5)6 FIRMWARE UPGRADES (5)7 DRIVER INSTALLATION AND OPERATION ..................................................................... 6 7.1 Windows 9x/XP/2k Driver Installation ............................................................................... 6 7.2 Macintosh and Linux drivers ............................................................................................. 9 8 CUSTOM FIRMWARE DEVELOPMENT ............................................................................ 9 9 ORDERING INFORMATION (10)N o tRe co m m e nd edf or N e wDe si gn1 IntroductionThe ETRX2USB wireless mesh networking USB Stick is effectively an RS232 to USB bridge connected to an ETRX2 ZigBee module. This allows connectivity to a computer’s USB port. The supplied drivers create a virtual COM Port, so that the command line of the ETRX2 can be accessed via any terminal software application.When using Windows ® 9x/XP/2000 the Telegesis Terminal application can be used as described in the Development Kit manual.1.1 Supported Operating Systems∙ Windows 98SE ∙ Windows XP ∙ Windows 2000 ∙ MAC OS-9 ∙ MAC OS-X ∙ Linux2 Absolute Maximum RatingsTable 1: Absolute Maximum RatingsThe absolute maximum ratings given above should under no circumstances be violated. Exceeding one or more of the limiting values may cause permanent damage to the device.N o tRe co m edf or N e wDe si gn3 Operating ConditionsTypical values at 5V 25°C.Table 2: Operating Conditions4 Other dataFor further technical information, including radio certification, see the ETRX2 or ETRX2PA Module Product Manual.If you purchase ETRX2USB sticks without printed markings on the case, you may be responsible for applying a marking appropriate to their geographical area of use, such as the FCC certification. For more information on ZigBee® compliance and the AT command interface firmware please refer to the latest AT command dictionary and the ETRX2 user guide.1 During USB suspend the current will drop by 25.6mA in all modes.2 Please note that the power consumption in various power modes is firmware and usage dependent.N o tRe co mm e nd en5 ETRX2 I/O ConnectivityThe I/Os of the built in ETRX2 are connected as follows:∙ I/O1 is connected to the LED (drive I/O1 low to sink LED).∙ I/O2 is the CTS input for the ETRX2. Make sure I/O2 is never defined as an output. ∙ I/O4 is the RTS input for the ETRX2.Important Note: The lines for hardware handshaking are connected, so even when not using hardware handshaking I/O2 should never be defined as an output as this would drive against the incoming CTS signal via a 1k Ω resistor and increase the current consumption.Note that if you use the command “AT&F” on the USB stick, I/O1 will revert to being an input and the LED will not light up. To restore its function as a pilot light, use the command “ATS0E=00FA” (with R2xx firmware) or “ATS17=00FA” (with R3xx) followed by a reset.6 Firmware upgradesThe firmware which is loaded onto the embedded ETRX2 Module can be upgraded over the air or via the virtual COM port as described in the Development Kit manual.Alternatively, access to the SIF programming interface is possible by opening the cover on the side of the ETRX2USB ZigBee USB stick.N o tRe co m m e nd edf or N e wDe si gn7 Driver Installation and OperationThe drivers provided will generate a virtual COM port allowing easy access to the serial port of the embedded ETRX2.To read more about the ETRX2 wireless mesh networking module and its command line interface please read the corresponding documentation which can be found at /telegesisdocuments .7.1 Windows 9x/XP/2k Driver InstallationThe driver package downloadable from the Support Software download page of /telegesissoftware should be unzipped into a local folder. When executing the file ‘TgVCPInstaller.exe ’ prior to plugging in the ETRX2USB stick an installer will guide you through the steps required for the driver installation. If prompted that the driver has not passed the W indows logo test simply press ‘Continue Anyway’.Figure 1: Found New Hardware WizardAfter insertion of the stick, Windows ® will prompt that new hardware has been found. If you have run the ‘TgVCPInstaller.exe ’ Windows will be able to install the driver by automatically as shown in Figure 2. If you have not run ‘TgVCPInstaller.exe ’ you will have to manually point to the directory into which you have unzipped the driver.N o tRe co m m e nd edf or N e wDe si gnFigure 2: Install software AutomaticallyFigure 3: Windows Logo TestPlease note that each ETRX2USB has a unique serial number which requires the installation procedure to be repeated with every new ETRX2USB being attached to the computer. This allows multiple ETRX2USB sticks to be used on the same computer at any one time.In order to find out the identity/number of the virtual com port the stick has been assigned to, please enter the Device Manager under the Windows Computer Management screen (see below) and click on the Ports (COM and LPT) section where you should find the new virtual COM port. By double clicking on the entry of the virtual COM port you can also change the number assigned to the virtual COM port when entering the advanced setup of the device.N o tRe co m m e nd edf or N e wDe si gnFigure 4. Device ManagerOnce the correct COM port has been selected, the Terminal software can be used to control the ETRX2USB stick as per the Development Kit Manual.Figure 5. Telegesis TerminalN o tRe co m m e nd edf or N e wDe si gn7.2 Macintosh and Linux driversA Virtual Com Port driver kit for Mac and Linux can be obtained by following the link on our website on the Support Software download page.In addition, one of our customers has written a Linux driver that will be included in the 2.6.25 kernel. It can be found at /pub/linux/kernel/people/gregkh/gregkh-2.6/patches/. (Note that this is for information only, and this software was developed entirely outside Telegesis.) Most Linux distributions now include suitable native drivers.8 Custom Firmware DevelopmentIf you intend to develop custom firmware to go onto the ETRX2USB you need to contact SiLabs to obtain access to their suite of development tools and their stack. The USB stick contains an ETRX2 module based on the SiLabs EM250 and a USB-to-serial bridge chip. The ETRX2 communicates via its serial port , so the user’s firmware must use the UART of Serial Controller 1. The nRTS and nCTS lines are connected to the USB bridge chip. The LED on the USB stick is driven from ETRX2 pad I/O1, which is EM250 pin GPIO14.In order to download custom firmware onto the ETRX2, the Ember bootloader can be used or alternatively the ETRX2USB can be directly connected to the Ember InSight Adapter for programming and real time debugging.N o tRe co m m e nd edf or N e wDe si gn9 Ordering InformationTable 11. Ordering InformationN o tRe c Silicon Laboratories Inc.400 West Cesar Chavez Austin, TX 78701USASmart.Connected.Energy-Friendly Products/products Quality /quality Support and Community Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laborato-ries Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. N o t R e co m m e n d e d f o r N e w D e s i g n。
User GuideAC600 Mini Wireless USB AdapterArcher T2U©2019 TP-Link REV3.0.0 1910012549ContentsAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Chapter 1. Get to Know About Your Adapter. . . . . . . . . . . . . . . . . . . . . . . 21. 1. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2. LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Chapter 2. Connect to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Chapter 3. Windows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63. 1. Install Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. 2. Join a Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 3. Uninstall Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Chapter 4. Mac OS X. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94. 1. Install Driver and Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4. 2. Join a Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124. 2. 1. TP-Link Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124. 2. 2. WPS (Wi-Fi Protected Setup). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4. 3. Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4. 4. Uninstall Driver and Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Appendix: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19About This GuideThis guide is a complement to Quick Installation Guide. The Quick Installation Guide instructs you on quick installation, and this guide provides the product overview and detailed instructions for each steps.When using this guide, please notice that features of the adapter may vary slightly depending on the model and software version y ou have. All screenshots, images, parameters and descriptions documented in this guide are used for demonstration only.ConventionsIn this guide, the following conventions are used:*Maximum wireless signal rates are the phy sical rates derived from IEEE Standard 802.11 specifications. Actual wireless data throughput and wireless coverage, and quantity of connected devices are not guaranteed and will vary as a result of network conditions, AP limitations, and environmental factors, including building materials, obstacles, volume and density of traffic, and AP location.*To ensure compatibility, you may need to update the adapter’s drivers after an OS update. You can find our latest drivers in the download center at /en/download-center.More Info• The latest software and utility can be found at h ttps:///download-center.• The Quick Installation Guide (QIG) can be found where you find this guide or inside the package of the product.• Specifications can be found on the product page at https://.• Our Technical Support contact information can be found at the Contact Technical Support page at https:///support.Chapter 1Get to Know About Your AdapterThis chapter introduces what the adapter can do and shows its appearance. This chapter contains the following sections:• Product Overview• LED StatusChapter 1Get to Know about Your Adapter1. 1. Product OverviewTP-Link Wireless USB Adapter connects your computer to a Wi-Fi network for smooth HD video, voice streaming and online gaming.• 256QAM technology increases 2.4GHz data rate from 150 Mbps to 200 Mbps for 33% faster performance• Selectable dual-band connections for lag-free HD video streaming and gaming• Much smaller than a flash drive, enjoy a stable and fast AC600 Wi-Fi wherever you need it• Utilizes 802.11ac standard and is backward compatible with 802.11a/b/g/n• Supports 64/128 bit WEP, WPA-PSK/WPA2-PSK• Supports Windows and Mac1. 2. LED StatusYou can check the adapter’s working status by following the LED Explanation table.Tips:If the LED is off, try these troubleshooting tips:1. Check if the adapter is recognized and enabled or not. Refer to Troubleshooting-T2 for detailed instructions.2. Remove and reinsert the adapter.3. Reinstall the software, if necessary.Chapter 2Connect to a Computer This chapter introduces how to connect the adapter to your computer.Chapter 2Connect to a Computer Before y ou start using y our adapter, insert the adapter into a USB port on y our computer directly.* The image is for demonstration only.After connecting your adapter to the computer, please follow the instructions in the appropriate chapter for your operating system: Windows, Mac OS X.Chapter 3WindowsThis chapter introduces how to install your adapter’s driver, use your adapter to join a wireless network, and uninstall your adapter in a Windows system. The adapter is equipped with a Setup Wizard, which can guide you through the installation process. This chapter includes the following sections:• Install Driver• Join a Wireless Network• Uninstall Driver3. 1. Install Driver1. Insert the resource CD into your CD drive and run the Autorun.exe from the pop-upAutoplay window.Note:1. You can also download the driver or check the new release at https:///download-center.2. In some operating systems, the CD screen will pop up automatically. Otherwise, run the CD manually. 2. Select Archer T2U and follow the instructions to complete the installation.Note:If you can’t install the driver successfully, disable the antivirus software and firewall, then try again.3. When the following screen appears, the driver has been installed successfully.3. 2. Join a Wireless NetworkYou can join a wireless network via Windows built-in wireless utility. Follow the instructions below to use your computer system’s built-in wireless utility:1. Click , or (Network icon) on the taskbar. Select the Wi-Fi network you want to join, and click Connect. Enter the network password when prompted.2. When the network icon changes to or , it indicates a successful network connection.3. 3. Uninstall DriverThe software uninstallation steps vary a bit from different sy stems. Please follow the appropriate instructions for y our Windows operating sy stem: Windows 8/8.1/10, Windows XP/7.• Windows 8/8.1/10Go to Start menu to find the TP-Link application. Click Uninstall TP-Link Archer T2U Driver, then follow the on-screen instructions to complete the uninstallation.• Windows XP/7Go to Start > All Programs > TP-Link > Uninstall TP-Link Archer T2U Driver. Follow the on-screen instructions to complete the uninstallation.Chapter 4Mac OS XThis chapter introduces how to install your adapter’s driver and utility, use your adapter to join a wireless network, manage your adapter and uninstall your adapter in Mac OS X.This chapter includes the following sections:• Install Driver and Utility• Join a Wireless Network• Management• Uninstall Driver and Utility4. 1. Install Driver and UtilityWe take the steps in Mac OS X 10.10 as an example - the steps may vary slightly for other versions of Mac OS.1. Download the driver and utility at https:///download-center.Note:The CD is included in the package. If your computer has a CD drive, you can also run the included CD to install the driver and utility.2. Double click to unzip the downloaded folder and run the Install.pkg.3. The Install TP-Link Wireless USB Adapter Utility and Driver Wizard window willappear. Click Continue and follow the instructions to complete the installation.4. When the following screen appears, the driver and utility have been installedsuccessfully. Click Restart to finish the installation.5. After restarting the computer, the TP-Link Utility icon will appear on the menubar in the upper-right corner of the screen. To use the utility to join a Wi-Fi network with your adapter, refer to Join a Wireless Network.Note:If the TP-Link Utility icon does not appear on the menu bar, make sure the USB wireless network adapter is connected properly and its LED is on.4. 2. Join a Wireless NetworkThere are two options of using the adapter to join a Wi-Fi network.Option 1: TP-Link UtilityTP-Link Utility lets you easily connect the adapter to a Wi-Fi network and manage the adapter.Option 2: WPS (Wi-Fi Protected Setup)WPS (Wi-Fi Protected Setup) is a network security standard for easily adding computers and other devices to a home network. Use this method if your wireless router or access point supports WPS.4. 2. 1. TP-Link UtilityOption 1Click the TP-Link Utility icon on the menu bar, and choose a Wi-Fi network from the list. Enter the password when prompted.When you are connected to the internet, the network icon will change to .Option 21. Click the TP-Link Utility icon on the menu bar, and then click Open WirelessUtility at the bottom of the network list.2. Select the network you want to join from the list and enter the password whenprompted. Click Join.Note:If your Wi-Fi network is not displayed in the list, you can try to join it by WPS or by clicking Join Other on the above screen, and then follow the on-screen instructions to join the network.4. 2. 2. WPS (Wi-Fi Protected Setup)WPS can be activated via PBC (Push Button Configuration) and PIN code on the TP-Link Utility. Please refer to PBC or PIN below.• PBC1. Press the WPS/QSS button on your router or AP.2. Within 2 minutes, click the TP-Link Utility icon on the menu bar, and then click WPS at the bottom of the network list.3. Click PBC.4. The following screen indicates a successful connection by WPS. Click OK.• PIN1. Click the TP-Link Utility icon on the menu bar, and then click WPS at the bottom of the network list.2. Click PIN.3. Within 2 minutes, log in to the web management page of your router or AP. Go to its WPS page, enter the PIN of the adapter in the corresponding field and click Connect.4. The following screen indicates a successful connection by WPS. Click OK.4. 3. ManagementTP-Link Utility provides you with an easy way to manage various connection settings of your Wi-Fi network.1. Click the TP-Link Utility icon on the menu bar, and then click Open WirelessUtility at the bottom of the network list.2. TP-Link Utility will pop up. Click the Profiles button to open the Profiles screen.3. The Profiles screen lets you manage different Wi-Fi connection settings as profilesso that you can connect to your network easily.Preferred Networks displays the networks that you once connected to. The networks’ status and information are displayed in the table.• To join a Wi-Fi networkIf you want to join a Wi-Fi network that is listed on the profile screen, select the profile and click Apply in the bottom right corner.• To manage an existing profileIf you want to change the wireless settings of an existing profile, select it and then you can edit its Security and Password. If you want to delete a profile, select it and click Remove.4. 4. Uninstall Driver and Utility1. Double click mand in the downloaded folder.2. Enter the password of you computer and when the “Uninstall Complete” messageappears, the uninstallation is complete.Appendix: TroubleshootingT1. W hat should I do if the adapter is not detected?• Make sure the adapter is securely connected to the computer.• Make sure you meet the minimum system requirements for the adapter and that the latest Windows and system updates are installed on your computer.• Make sure you use the latest driver for your specific adapter. The latest drivers can be found at the product’s Support page at https:///download-center.• Try a different USB port on the computer.• Try restarting the computer or try using the adapter on a different computer.T2. H ow to check if I have installed the driver for my adapter successfully or not?1. On your computer, please right click Computer icon and go to Manage;2. Open the Device Manager and go to Network adapters, and then find thecorresponding TP-Link adapter, right click it and then go to Properties;3. If you can see “This device is working properly.” in the red box, you have alreadyinstalled the driver successfully.T3. W hat should I do if can’t connect to the Wi-Fi after installing the driver?• Refer to T2to check if you have installed the driver for your adapter successfully .• Make sure the adapter is securely connected to the computer.• Disable the antivirus software and firewall, then try again.• Try a different USB port on the computer.• Restart your computer and try again.• Re-install the driver and try again.T4. H ow to find the hardware version of the adapter?• The hardware version is printed on the product label on the package or the adapter.There is a character string “Ver:X.Y” (for example, Ver:2.0) in the Serial Number field, and the number X is the hardware version of the adapter.• Visit /faq-46.html and follow the second method to find the hardware version of the adapter.For more detailed instructions:• Can’t find the hardware version of the adapter: https:///faq-46.html • Can’t find or join the wireless networks: https:///faq-2253.html• Can’t install the driver: https:///faq-2252.htmlFCC compliance information statementProduct Name: AC600 Mini Wireless USB AdapterModel Number: Archer T2UResponsible party:TP-Link USA Corporation, d/b/a TP-Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https:///us/Tel: +1 626 333 0234Fax: +1 909 527 6803E-mail:*********************This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1 ) This device may not cause harmful interference.2 ) This device must accept any interference received, including interference that maycause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.FCC RF Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand. SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance.We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.Issue Date: 2019.02.18CE Mark WarningThis is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.OPERATING FREQUENCY (the maximum transmitted power)2400MHz-2483.5MHz (20dBm)5150MHz-5250MHz (23dBm)5250 MHz -5350 MHz (20dBm)5470 MHz -5725 MHz (20dBm)EU declaration of conformityTP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU and 2011/65/EU.The original EU declaration of conformity may be found at https:///en/ ce.RF Exposure InformationThis device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. This device has been tested and meets the ICNIRP exposure guidelines and the European Standard EN 62209-2. SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Carry this device at least 0.5 cm away from your body to ensure exposure levels remain at or below the as-tested levels.National restrictionsAttention: This device may only be used indoors in all EU member states and EFTA countries.Canadian Compliance StatementThis device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:1 ) This device may not cause interference.2 ) This device must accept any interference, including interference that may causeundesired operation of the device.L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:1 ) l’appareil ne doit pas produire de brouillage;2 ) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, memesi le brouillage est susceptible d’en compromettre le fonctionnement. Caution:1 ) The device for operation in the band 5150–5250 MHz is only for indoor use to reducethe potential for harmful interference to co-channel mobile satellite systems;2 ) For devices with detachable antenna(s), the maximum antenna gain permitted fordevices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;3 ) For devices with detachable antenna(s), the maximum antenna gain permitted fordevices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; andThe high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.DFS (Dy namic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-5600MHz, and 5650-5725MHz.Avertissement:1 ) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquementpour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;2 ) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limitation P.I.R.E.;3 ) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l’exploitation point à point et non point à point, selon le cas.En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pourles bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.Les produits utilisant la technique d’atténuation DFS (sélection dy namique des fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz. Radiation Exposure Statement:This EUT is compliance with SAR for general population/uncontrolled exposure limits in RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance 1.0 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.Industry Canada StatementCAN ICES-3 (B)/NMB-3(B)Korea Warning Statements당해 무선설비는 운용중 전파혼신 가능성이 있음.NCC Notice注意！依據 低功率電波輻射性電機管理辦法第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。
U盘操作U盘基本要求：建议正版金士顿品牌，容量不大于4G，分区格式为FAT32。
测试U盘是否正常使用，将U盘插到考勤机的USB口后，进入考勤机[优盘操作]---[导出记录和日志]，如果导出成功，则表示U盘可用，若提示‘请插入U 盘’，则将考勤机断电再通电。
C/S软件中U盘操作：1：将U盘插到计算机上，在设备服务程序\设备信息\新增设备信息\U盘连接，名称随便起输入考勤机的IP地址，这是在U盘中建一个文件夹的过程，可以看到U盘中生成一个WEDS4-U 的文件夹，点击保存。
2：设备建好后，点击右边的写入（档案\照片\指纹）这是将数据库中的人员信息写入到U 盘里面。
3: 将U盘从计算机上拔出，插到考勤机上，选择‘U盘操作’中的导入档案，这是将U盘里面的人员信息转移到考勤机上。
4：此时可以到考勤机的‘档案管理’里面查看一下人员信息。
并在考勤机上给员工发卡或者录指纹或者对员工改密码等操作。
做完这些操作后，需要在考勤机上‘导出记录和操作日志’，此次是将发卡、录指纹或者改完的密码这些信息传到U盘里面。
5：将U盘从考勤上拔下插入计算机，在设备服务程序里面，读取操作日志这步操作是为了将存在U盘中的从考勤机导出的指纹、卡号等信息导入到软件存起来，读取考勤记录是将在电脑上的考勤记录和考勤照片取到软件中来6：此时如果将考勤断电，那么考勤机中的指纹或卡片的所有信息都清除掉，那么为了避免因为断电人员无考勤，所以最好在执行一次下写入（档案/照片/指纹），以后员工可以考勤了。
B/S软件中的U盘操作整体流程和C/S软件相同，只是操作的界面不同。
（添加U盘设备的图片）（设备通讯的图片）注：U盘连接，需要注意，IP地址一定要与考勤机的IP地址相同，且有多台考勤机使用U盘传输，一定要区分开设备的IP地址。
U盘传输时需要通过IP地址区分考勤机连接。
所以多台设备可以共用一个U盘。
由于U盘的稳定性并不强，为了防止U盘损坏造成导出的数据丢失，使用U盘连接的用户，可以开启考勤机数据备份的功能，在每次导出数据时会在考勤机中，自动备份一份数据文件。
d2 USB 3.0D E S I G N BY N E I L P O U LTO NProfessional Hard DiskSuperSpeed USB 3.0 | Hi–Speed USB 2.0Eco ManagementDeveloped with the environment in mind, the LaCie d2 USB 3.0 helps you reduce power consumption by switching to its eco mode after 30 minutes of inactivity. For better energy efficiency, it will also automatically shut down when unplugged from the computer. On top of that, it’s recyclable and ROHS-compliant.SuperSpeed USB 3.0The d2 USB 3.0 gives you SuperSpeedperfomance. Featuring 7200 rpm drives, the d2 USB 3.0 reaches up to 156MB/s, making it ideal for creative professionals looking for high transfer speeds. With an advanced backup solution for Mac ® and PC, it is also perfect for any workstation setup and it’s compatible with USB 2.0. It’s even USB 3.0-compatible on Mac computers, thanks to LaCie’s USB 3.0 driver for Mac OS.Clever, Advanced DesignThe d2 USB 3.0 is designed to integrate into any professional work environment. Sturdy and compact, it is ideal for intensive professional use. The unique and ultra-quiet, fanless aluminum heat sink design gives you 60% more surface area for heatdissipation for high reliability. The LaCie d2 USB 3.0 is versatile and can stand upright, be stacked horizontally with other drives or rackmounted to save desktop space.• Superior burst transfer rates up to 156MB/s (USB 3.0)• USB 3.0 connection compatible with USB 2.0• Space-saving versatility: stack, rackmount or stand upright• Compatible with Mac and PCUSB 3.0 direct connectionPower adaptor connectionKensington lock slot1TB **=2 hours of uncompressed HD video or 70 hours of DVD or 77,500 RAW photos ***Features• USB 3.0 speed: up to 156MB/s• Aluminum fanless cooling design for quiet operation• Optimized power management• Space-saving design for upright, rackable or stackable configurationsBox Content• LaCie d2 USB 3.0• SuperSpeed USB 3.0 cable (USB 2.0 and 1.1 compatible)• Drive stand for upright use• External power supply• LaCie Utilities and Software (preloaded on the drive):• LaCie Backup software with data restore for Windows® and Mac • User Manual• Quick Install GuideMinimum System Requirements• Computer with a USB 3.0 or USB 2.0 port• High-speed Internet for online storage• Latest version of Windows XP, Windows Vista®, Windows 7 /Mac OS X 10.5, 10.6• Minimum free disk space: 600MB recommendedFor USB 3.0 Mac compatibility:• Mac Pro compatible with LaCie USB 3.0 PCI Express Card(requires available PCI Express slot)• MacBook® Pro compatible with LaCie USB 3.0 ExpressCard/34(requires available ExpressCard slot)LaCie d2 USB 3.0Simply switch on or off withone button1-CLICK POWER SETTING*Burst transfer rates vary from one computer to another and may vary slightly from one drive to another. Average speed is usually lower, depending on host configuration.**1TB (T erabyte) = 1000GB. 1GB = 1,000,000,000 bytes. T otal accessible capacity varies depending upon operating environment (typically 5–10% less).***Calculations are based on approximately 13GB/hour of DV video, 2.85MB/MP3 song, and 1MB/JPEG photo. © 2010, LaCie. The LaCie logo is a trademark of LaCie. Other products and brand names mentioned herein may be trademarks or registered trademarks of their respective owners. Specifications and appearance are given as guidelines and may change without notice. 101025Premium 3 Year WarrantyThe d2 USB 3.0 comes with a 3 Year Limited Warranty. For superior service, it also comes with the LaCie Advance Care Option, which can be purchased separately online within 30 days of the purchase date. Under the Advance Care Option, LaCie will immediately swap out the product without it needing to be returned first for minimal interruption of your workflow. LaCie covers all freight costs. Availability depends onthe sales area. See for details.d2 USB 3.0D E S I G N B Y N E I L P O U LTON。
中控考勤软件U盘操作软件截图
进入U盘数据管理界面
说明：
登陆软件
点击“数据（F）”
选择USB闪盘管理
说明：
选择“彩屏或OP1000自助式指纹机…”
点击确认
从U盘导入数据至电脑
说明：
若员工姓名/工号都在考勤机上登记，且员工信息有更新时，则先将考勤机的中的人员信息导入至U盘然后再执行该操作
选择“导入用户数据至电脑”
点击“从U盘导入用户数据”
确认
说明：
导入记录数据至电脑即是将员工的打卡记录导入至电脑
点击“导入记录数据至电脑”
点击“从U盘导入数据”
选择时间段
点击查询，查询结果为选定员工范围在指定时间段内容的所有员工打卡记录。
如：财务部所有员工2012-12-01–2012-12-31的所有员工打卡记录
只要U盘已将最新记录数据导入至电脑，则该操作可以查询出所有的员工打卡记录
点击“导出”可将查询出的员工打卡记录导出成Excel表格
报表统计
说明：
点击“统计报表”
选择部门选择员工
选择统计时间段
点击“查询计算”
软件默认显示的是“班次明细情况表”，若想查看其它报表，参考其它界面截图 若想将统计出的报表导出成Excel表格，点击“导出数据”。
SUMMIT系统用户手册------------轻便、灵活的地震数据采集系统………………………Summit II plus系统Summit II plus系统是早期的Summit系统的新一代产品，两种系统相互间是完全兼容的。
SummitII plus系统由下面单元构成：USB接口数据采集单元RU中继单元RP触发单元TU电缆手持袖珍定位仪USB接口通过USB连接线将主机（笔记本电脑）和地震排列连接起来。
由于采用了即插即用的USB技术，所以可以在任何时候把USB接口与地震排列连接或断开。
此外，USB接口可以连接到地震排列的任何位置上。
●在USB接口的上面有一个电源/数据线接口（母的）和三个状态指示灯●在USB接口的前面有四个BNC插口用于触发信号的输出或输入。
●在USB接口的后面有一个电源/数据线接口（公的），一个USB通讯接口及一个外部供电电源接口。
下面将加以详细描述：USB接口上面USB接口前面USB接口下面上面在USB接口的上面有一个电源/数据线接口（母的）和三个状态指示灯：注意：在仪器软件升级时，所有的三个指示灯都亮。
在升级完成后，三个指示灯都闪烁。
前面板在USB接口的前面有4个与触发相关的BNC插头:后面板USB接口的后面板有一个电源/数据线接口（公的），一个USB通讯接口和外接电源插头。
数据采集单元（RU）是应用24位α-γ技术的A/D转换器的两道地震数据采集单元。
所有的数据采集单元（RU）均通过USB接口由笔记本电脑（中央单元）控制和监视。
数据和控制指令完全是数字信号传送。
必须应用外部电池给数据采集单元（RU）供电。
所有数据采集单元（RU）的器件都内置于牢固的金属外壳内，以保证其最大的稳定性和抗雷电能力。
每一个数据采集单元（RU）有一个唯一的物理地址编号（在标签上），内含2块电路板：分别叫做SPM（信号处理模块）和BMP（蓝牙电源模块）。
SPM负责采集数据的前置放大，滤波，数字化，叠加，相关和储存。
T2 720P红外夜视U盘产品概述：本产品是最新款红外迷你数码U盘，产品集拍照·录像·红外夜视·边充电边录像于一体的高清数码迷你U盘，方便您在各种场合使用。
产品采用高清DV处理芯片，让您拍摄出来的画面更加清晰流畅，采用进口超强红外夜视灯，在光线比较昏暗的情况下摄录效果一样清晰完美。
外观精致大气，操作键隐藏式的完美设计，手感舒适，自带USB2.0高速接口即插即用。
内置高性能聚合物锂电池，工作时间长达1小时。
产品示意图：产品功能概述：1.开机：长按A键，红蓝灯闪烁三下，蓝灯常亮进入待机状态。
2.录像：在待机状态下，长按B键，红灯闪三下熄灭后开始录像，在录像状态下，按B键一下停止并保存录像。
3.拍照：在待机状态下，短按B键，红灯慢闪一下，拍一张照片。
4.夜视录像：在待机状态下，短按A键蓝灯闪烁三下后熄灭，开启夜视并开始录像，在夜视录像过程中长按A键红灯闪烁三下后熄灭，关闭夜视并保存夜视录像。
5.边充边录：机器在待机状态下，只要接上电源就可以边充电边录像，在边充电边录像状态下，拔掉电源，红灯闪烁三次后熄灭，此时表示机器已关机并自动保存录像。
6.关机：长按A建，红灯闪烁三下后熄灭，表示机器已关机。
7.U盘模式：在关机状态下，机器USB连接至电脑，找到可移动磁盘，即可读取视频文件。
8.充电：机器在关机状态下，连接USB至电脑，或者接上220V充电器都可进行充电，充电时红蓝灯闪烁，充满电后红灯常亮。
9.修改时间：本机只要装上TF卡后连接电脑会自动带有修改时间的文档，如长时间不使用时间不准确的话，可打开机器TF卡里的文档（time,txt),修改成当前的时间并保存文档。
文档格式为：2014-03-30 12:21:55备注：本机最大支持32G TF卡，在任何录像状态下，只要TF卡存储满视频，机器默认为循环录像。
本机默认为10分钟一个视频文档。
复位：在任何操作下机器出现死机状态的，可同时按下机器上的A,B 键复位。
Hi-Speed USB 2.0 Flash Disk 高速USB 2.0行動碟中文使用手冊目錄產品介紹 (3)產品特色 (3)系統需求 (4)使用前須知 (4)安裝驅動程式 (5)在Windows98/98SE 下安裝驅動程式....................................5 ~ 6 安裝應用程式 (7)應用工具程式安裝說明 (7)製作移動磁碟之分割區及保密功能設定 (7)應用工具程式操作介面說明 ………………………………………7 ~ 11磁碟分割及保密設定功能 …………………………………………7 ~ 11保密磁碟登入功能 (12)磁區變更及密碼設定功能 (13)單獨密碼變更設定功能……………………………………………14 ~ 15磁碟格式化設定功能………………………………………………16 ~ 17製作開機磁碟設定功能……………………………………………18 ~ 19產品介紹感謝您購買本公司產品Hi-Speed USB Flash Disk! 本產品是為您設計的人性化、安全、輕巧的可移動式儲存裝置。
只要將本裝置插入USB port, 您的電腦將會快速偵測到本裝置而不需重新開機。
您可以在本裝置上做檔案的讀, 寫, 複製和刪除, 就如同其它的磁碟機一樣。
由於它的高容量，您更可以使用本裝置來播放MP3, 影片或執行其它的應用程式。
此外，本產品亦支援Windows Vista 之Ready Boost 功能，在不需更動電腦的硬體下，插上USB Port ，即可提升作業系統的效率。
本產品提供磁碟分割及密碼管理的功能，只需使用本產品所附屬之USB Flash Disk之應用工具程式，即可輕鬆完成您磁碟的管理及保護個人重要的資料。
產品特色商務和個人的智慧安全可移除式資料儲存裝置。
完全相容於通用序列匯流排(Universal Serial Bus Specification v2.0 and v1.1)。
JetFlash™ 中文使用手冊(版本 1.1)目錄產品介紹 (2)包裝內容 (2)產品特色 (2)系統需求 (2)安裝驅動程式 (3)在Windows® 98SE（第二版）下安裝驅動程式 (3)在Windows® Me、2000 及XP 下安裝驅動程式 (3)在Mac® OS 9.0或之後的版本下安裝驅動程式 (3)在Linux® Kernel 2.4.2或之後的版本下安裝驅動程式 (3)將JetFlash™ 格式化 (4)如何安全地移除JetFlash™ (5)在Windows® 98SE (第二版)下移除JetFlash (5)在Windows® Me、2000及XP下移除JetFlash (5)在Mac® OS 9.0, 或更新的版本; 及Linux® Kernel 2.4.2, 或更新的版本下移除JetFlash (5)JetFlash™ 150 系列產品 (6)產品規格 (6)訂購資訊 (6)JetFlash™ 120系列產品 (7)產品規格 (7)訂購資訊 (7)JetFlash™ 110系列產品 (8)產品規格 (8)訂購資訊 (8)JetFlash™ 2A系列產品 (9)產品規格 (9)訂購資訊 (9)產品介紹感謝您選購創見資訊所生產製造的JetFlash™ 。
本產品能讓您更方便且快速地在個人電腦與筆記型電腦間，存取及傳輸大量資料。
由於本產品提供較傳統儲存裝置更高的容量、及更快的傳輸速率，其功能可用來儲存/備份/傳輸您的檔案、資料夾、文件、照片及其它的電子檔。
此外它的超強可攜性及資料保存能力，搭配令人驚豔的流線外觀，絕對會帶給您截然不同的全新感受。
包裝內容JetFlash™系列產品之包裝盒內含有下列物品：JetFlash™頸繩應用軟體光碟USB延長線(只有JetFlash™ 2A 系列提供)快速安裝說明產品特色符合USB2.0 介面規格並相容於 USB1.1規格。
