海康威视网络摄像机操作手册V2.0.0

网络摄像机快速指南前言本节内容的目的是确保用户通过本手册能够正确使用产品，以避免操作中的危险或财产损失。

在使用此产品之前，请认真阅读产品手册并妥善保存以备日后参考。

使用前说明●访问本公司官网（）获取说明书、应用工具和开发资料。

●使用前请先对设备进行校时，校时的具体配置方法请参见《网络摄像机操作手册》。

符号约定对于文档中出现的符号，说明如下所示。

安全使用注意事项●产品安装使用过程中，必须严格遵守国家和使用地区的各项电气安全规定。

●请使用正规厂家提供的电源适配器，电源适配器具体要求参见产品参数表，建议为每台设备配备独立的适配器。

●根据国家相关标准，对弱电设备供电时，要求供电电流不超过8A并且功率不超过100W，防止发生安全事故。

●为减少火灾或电击危险，请勿让产品受到雨淋或受潮。

●应该在建筑物安装配线中组入易于使用的断电设备。

●在设备安装时，请确保产品固定牢固。

●如果产品工作不正常，请联系购买产品的商店或最近的服务中心，不要以任何方式拆卸或修改产品。

（对未经认可的修改或维修导致的问题，本公司不承担任何责任）。

●避免将产品安装到振动或冲击环境，并使产品远离电磁干扰的地点。

（忽视此项可能会损坏产品）。

●请勿直接触碰产品散热部件，以免烫伤。

●室内产品请勿安装在可能淋到水或其他液体的环境。

●请勿在极热、极冷、多尘、有腐蚀性、高盐碱或者高湿度的环境下使用产品，具体温、湿度要求参见产品的参数表。

●设备需存放于干燥无腐蚀性气体环境，避免阳光直射。

●避免将镜头对准强光（如灯光照明、太阳光或激光束等），否则会损坏图像传感器。

●避免热量积蓄，保持产品周边通风流畅。

●请勿直接触碰到图像传感器，若有必要清洁，请将柔软的干净布用酒精稍微湿润，轻轻拭去尘污；当产品不使用时，请将防尘盖加上，以保护图像传感器。

●设备接入互联网可能面临网络安全问题，请您加强个人信息及数据安全的保护。

当您发现设备可能存在网络安全隐患时，请及时与我们联系。

海康威视网络摄像机用户手册WORD格式说明书网络摄像机操作手册V2.0.0杭州海康威视数字技术股份有限公司技术热线：400-700-5998-3安全须知此内容的目的是确保用户正确使用本产品，以避免危险或财产损失。

在使用此产品之前，请认真阅读此说明手册并妥善保存以备日后参考。

如下所示，预防措施分为“警告”和“注意”两部分：警告：无视警告事项，可能会导致死亡或严重伤害。

注意：无视注意事项，可能会导致伤害或财产损失。

警告事项提醒用户防范潜在的死亡或严重伤害危险。

注意事项提醒用户防范潜在的伤害或财产损失危险。

警告：1.请使用满足SELV（安全超低电压）要求的电源，并按照IEC60950－1符合Limited Power Source(有限电源)的额定电压为12V直流或24V交流电源（根据具体型号而定）供应。

2.如果设备工作不正常，请联系购买设备的商店或最近的服务中心，不要以任何方式拆卸或修改设备（未经许可的修改或维修所导致的问题，责任自负）。

3.为减少火灾或电击危险，请勿让本产品受到雨淋或受潮。

4.本安装应该由专业的服务人员进行，并符合当地法规规定。

5.应该在建筑物安装配线中组入易于使用的断电设备。

有关在天花板上安装设备的指示：安装后，请确保该连接至少可承受向下50牛顿（N）的拉力。

注意：1.在让摄像机运行之前，请检查供电电源是否正确。

2.请勿将此产品摔落地下或受强烈敲击。

3.请勿直接碰触到图像传感器光学元件，若有必要清洁，请将干净布用酒精稍微湿润，轻轻拭去尘污；当摄像机不使用时，请将防尘盖加上，以保护图像传感器。

4.避免对准强光（如灯光照明、太阳光等处）聚焦，否则容易引起过亮或拉光现象（这并非摄像机故障），也将影响图像传感其寿命。

5.激光束可能烧毁图像传感器，在激光装置被使用的情况下，请您一定注意不要让图像传感器的表面暴露于激光束之下。

6.避免置于潮湿，多尘，极热，极冷（正常工作温度：－10℃～＋60℃），强电磁辐射等场所。

Instrumentation Solutions for Hydrogen Applications Components and systems for use with gaseousand liquid hydrogen3ContentsOn-Board Vehicles - EC-79 Certified ComponentsApplications from 30 to 350 bar (435 - 5,076 psi) .................................................................................... 6 Two Ferrule Tube Fittings - A-LOK ® Series ............................................................................................ 6 Applications up to 700 bar (10,152 psi) ................................................................................................... 7 Medium Pressure Fittings - Cone and Thread - Autoclave Engineers ® ...................................................... 7 Medium Pressure Needle Valves SM Series - Autoclave Engineers ® ........................................................ 7 Medium Pressure Tubing - Autoclave Engineers ® . (7)ISO 19880-3 Certified Products for Hydrogen Refueling StationsMedium Pressure Needle Valves 20SM Series - Autoclave Engineers ® .................................................... 8 Medium Pressure O-Ring Check Valves CXO Series - Autoclave Engineers ® .. (8)General Hydrogen ApplicationsApplications up to 414 bar (6,000 psi)...................................................................................................... 10 Two Ferrule Tube Fittings - A-LOK ® Series ............................................................................................ 10 Ball Valves - B Series - Isolation and Directional Control Valves ............................................................... 10 Inline Filters - F Series ......................................................................................................................... 10 Check Valves - CO Series - Directional Control Valves ............................................................................ 11 Stream Switching Systems - R-Max TM Gen II Series ................................................................................ 11 Modular Sample Conditioning Systems - IntraFlow TM Series .................................................................... 11 Pressure Regulators - IR4000 and IR6000 Series ................................................................................... 11 Excess Flow Shutoff Valves - FS190 Series ............................................................................................ 11 Applications up to 1,380 bar (20,000 psi) ................................................................................................ 12 Medium Pressure Two Ferrule Inverted Tube Fittings - MPI TM Series ........................................................ 12 Medium Pressure Fittings - Cone and Thread - Parker Autoclave Engineers ® ........................................... 12 Permanent Ferrule-less Connectors - Phastite ® Series ........................................................................... 12 Ball Valves - Hi-Pro Series - Isolation Valves .......................................................................................... 12 Ball Valves - HB Series - Isolation Valves ............................................................................................... 12 Needle Valves MAN - MPI TM Series ....................................................................................................... 13 Medium Pressure Needle Valves 15SM and 20SM Series - Autoclave Engineers ® .................................... 13 Medium Pressure O-Ring Check Valves CXO Series - Autoclave Engineers ® ............................................ 13 Medium Pressure O-Ring Check Valves MAC - MPI TM Series ................................................................... 13 Double Block & Bleed Needle Type Manifold - 20DBNV Series - Autoclave Engineers ® ............................. 13 Relief Valves - Soft Seat RVS Series - Autoclave Engineers ® ................................................................... 14 Medium Pressure Tubing - MPI TM Series ................................................................................................ 14 Medium Pressure Actuators - Autoclave Engineers ® .............................................................................. 14 Medium Pressure Adapters - Autoclave Engineers ® ............................................................................... 14 Medium Pressure Accessories - Autoclave Engineers ® .. (14)Cryogenic/LH 2 ApplicationsGlobe Valves - Stainless Steel with Bronze Internals - Bestobell Industrial ................................................ 16 Globe Valves - Stainless Steel - Bestobell Marine .................................................................................. 16 Pneumatically Actuated Globe Valves - Stainless Steel with Bronze Internals - Bestobell Industrial ............. 16 Pneumatically Actuated Globe Valves - Stainless Steel - Bestobell Marine ............................................... 16 Lift Check Valves - Stainless Steel with Bronze Internals - Bestobell Industrial .......................................... 17 Lift Check Valves - Stainless Steel - Bestobell Marine ............................................................................. 17 Swing Check Valves - Stainless Steel - Bestobell Marine ........................................................................ 17 Manual Gate Valves - Bestobell Industrial . (17)Actuated Gate Valves - Pneumatic Tyre Design - Bestobell Industrial (17)Offer of SaleThe items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered into byParker will be governed by the provisions stated in Parker’s standard terms and conditions of sale (copy available upon request).45Your Reliable Partner for Driving the Energy Evolution ForwardParker is supporting the global decarbonisation efforts through a broad range of solutions for a variety of applications. Our hydrogen-compatible components and systems enable safe and efficient operation from vacuum to 1,380 bar (20,000 psi) and temperatures from -253O C to +538O C (-423O F to +1000O F).1,380 BAR20,000 PSIParker’s needle valves 20SM series and check valves CXO series havesuccessfully passed all the required tests for high pressure gas valves used in gaseous hydrogen stations of up to the H70 designation specified in ISO19880-3 certification.ON-BOARD VEHICLESTwo Ferrule Tube Fittings - A-LOK ®Series EC-79 CertifiedParker Autoclave Engineers ®:Medium Pressure Fittings EC-79 Certified Needle Valves - SM Series EC-79 Certified Medium Pressure Tubing EC-79 CertifiedISO-CERTIFIED PRODUCTS FOR REFUELING STATIONSParker Autoclave Engineers ®:Needle Valves - 20SM Series Tests Passed - Pending Certification Check Valves - CXO Series Tests Passed - Pending CertificationGENERAL HYDROGEN APPLICATIONSTwo Ferrule Tube Fittings - A-LOK ® SeriesPermanent Ferrule-less Connectors - Phastite ® SeriesBall Valves - B Series Ball Valves - Hi-Pro Series Ball Valves - HB Series Inline Filters - F Series Check Valves - CO SeriesStream Switching Systems - R-Max IIModular Sample Conditioning Systems - IntraFlow TM SeriesPressure Regulators - IR4000 and IR6000 SeriesExcess Flow Shutoff Valves - FS190 SeriesCRYOGENIC/LH 2 APPLICATIONSBestobell Cryogenic Valves:Globe ValvesPneumatically Actuated Globe ValvesLift Check Valves Swing Check Valves Manual Gate Valves Actuated Gate ValvesGENERAL HYDROGEN APPLICATIONSParker Autoclave Engineers ®:Medium Pressure Fittings - Cone and Thread Needle Valves - 15SM and 20SM Series Check Valves - CXO SeriesDouble Block & Bleed Needle Type Manifold - 20DBNV Series Relief Valves - RVS SeriesMedium Pressure Accessories and Adapters Medium Pressure Actuators Medium Pressure MPI TM Series:Fittings TubingNeedle Valves - MAN Series Check Valves - MAC Series67Applications from 30 to 350 bar (435 - 5,076 psi)On-Board VehiclesComponents for on-board hydrogen-powered vehicles for pressures from 30 to 700 bar (435 to 10,152 psi).EC-79 CertifiedParker’s range of products approved for use on-board hydrogen-powered vehicles from 30 to 700 bar includes tube fittings, needle valves and tubing. These products meet the general requirements of hydrogen components and systems used on hydrogen-powered motor vehicles as per regulation (EC) No 79/2009 of The European Parliament and of The Council of 14 Jan 2009.Two Ferrule Tube Fittings - A-LOK ® Series EC-79 CertifiedParker A-LOK ® two ferrule tube fittings are designed to achieve quality leak-free connections on-board hydrogen-powered vehicles up to 350 bar pressures and temperatures down to -40O C. These fittings provide reliable operation in cryogenic, pressure & thermal cycling and vibration applications. Manufactured at an IATF 16949 certified plant and EC-79 approved for hydrogen service, they come in a range of sizes and configurations in 316 Stainless Steel material. For optimised installation instructions see p.18 of this catalogue.To order EC-79 certified components, simply add the suffix EC79 at the end of your part number.For more details please see catalogue ref. 4190-FMTG.Applications up to 700 bar (10,152 psi)*A-LOK ® tees and crosses approved in sizes up to 1/2” (12mm). Please contact Parker for further information.Medium Pressure Fittings - Cone and Thread - Autoclave Engineers ® EC-79 CertifiedParker Autoclave Engineers medium pressure cone and thread connections are designed for applications that require higher flow rate capability. Manufactured from high tensile strength cold worked 316/316L Stainless Steel material as standard for 700 bar (10,152 psi) MAWP , this Medium Pressure range has all the benefits of the High Pressure version with all metal sealing for operations at temperatures from -40O C to +120O C (-40O F to +248O F).These fittings are designed for use with Parker Autoclave Engineers’ 20SM Series valves and medium pressure tubing according to ASME B31.3 Chapter IX standards.To order EC-79 certified components, simply add the suffix EC79 at the end of your part number.For more details please see catalogue ref. 02-0124SE. Medium Pressure Tubing - Autoclave Engineers ® EC-79 CertifiedParker Autoclave Engineers offers a complete selection of austenitic, cold drawn stainless steel tubing designed to match the performance standards of Parker Autoclave valves and fittings. Parker Autoclave Engineers medium pressure tubing is manufactured specifically for high pressure applications requiring both strength and corrosion resistance.For more details please see catalogue ref. 02-0124SE.Medium Pressure Needle Valves SM Series - Autoclave Engi-neers ®EC-79 CertifiedParker Autoclave Engineers SM Series valves are designed specifically for use with matching orifice medium pressure cone & thread fittings and tubing for the most efficient flow path possible using cone & thread style connections. They are manufactured using high tensile strength UNS S31600/S31603 cold worked 316/316L Stainless Steel material as standard for 700 bar (10,152 psi) MAWP .To order EC-79 certified components, simply add the suffix HYGEC79 at the end of your part number.For more details please see catalogue ref. 02-0112SE.E C -79E C -79C E R T I FI E DE C -7989ISO Products For H 2 Refueling StationsComponents for hydrogen refueling stations for pressures up to 700 bar (10,152 psi).Tests Passed, Pending ISO 19880-3 CertificationMedium Pressure Needle Valves 20SM Series - Autoclave Engineers ®Tested, Pending ISO 19880-3 CertificationThese Parker Autoclave Engineers 20SM Series Needle Valves (HYG option) have unique STEM/SEAT and PACKING design that can withstand temperatures ranging between -73°C and 316°C and pressures of up to 700 bar (10,152 psi).The valves are available with two different styles of connection options including cone & thread and MPI TM .To order ISO 19880-3 certified components, simply add the suffix HYG at the end of your part number.For more details please see catalogue ref. 02-0112SE.Parker’s needle and check valves have successfully passed the required tests for high pressure valves used in gaseous hydrogen stations as specified in ISO 19880-3 certification. These are now awaiting thecompletion of the final steps towards achieving the certification.Medium Pressure O-Ring Check Valves CXO Series - Autoclave Engineers ®Tested, Pending ISO 19880-3 CertificationThese Parker Autoclave Engineers O-Ring Check Valves CXO Series (HYG option) canwithstand temperatures ranging between -73°C and 316°C and pressures of up to 1,380 bar (20,000 psi).The valves are available with two different styles of connection options including cone & thread and MPI TM .To order ISO 19880-3 certified components, simply add the suffix HYG at the end of your part number.For more details please see catalogue ref. 02-0124SE.HALS2VI S O 880-3Other associated products for hydrogen refueling stations are featured on the following pages.1011General Hydrogen ApplicationsComponents for general hydrogen applications at pressures from vacuum to 1,380 bar (20,000 psi).Parker offers an extensive range of high-quality components and system solutions suitable for general hydrogen use in a wide variety of industries including power generation, petrochemical, agricultural and research & development.Applications up to 414 bar (6,000 psi)®Ball Valves - B Series - Isolation and Directional Control ValvesNeedle Valves - V Series - Isolation and Flow Control ValvesCheck Valves - CO Series - Directional Control ValvesInline Filters - F SeriesStream Switching Systems - R-Max TMGen II SeriesModular Sample Conditioning Systems - IntraFlow TM SeriesPressure Regulators - IR4000 and IR6000 SeriesExcess Flow Shutoff Valves - FS190 Series(10,000 psi).** Material de-rating and media compatibility factors need to be taken into consideration for higher temperature applications.For optimised installation instructions see p.18 of this catalogue.1213Medium Pressure Needle Valves 15SM and 20SM Series - Autoclave Engineers ®Medium Pressure O-Ring Check Valves CXO Series - Autoclave Engineers ®Medium Pressure O-Ring Check Valves MAC - MPI TMSeriesNeedle Valves MAN - MPI TMSeriesBall Valves - HB Series - Isolation ValvesBall Valves - Hi-Pro Series - Isolation ValvesApplications up to 1,380 bar (20,000 psi)Medium Pressure Two Ferrule Inverted Tube Fittings - MPI TMMedium Pressure Fittings - Cone and Thread - Parker Autoclave®Permanent Ferrule-less Connectors - Phastite ®SeriesDouble Block & Bleed Needle Type Manifold - 20DBNV Series - Autoclave Engineers ®This valve has been modified for use with Hydrogen. To order, add the suffix HYG at the end of your part number.This valve has been modified for use with Hydrogen. To order, add the suffix HYG at the end of your part number.* Material de-rating and media compatibility factors need to be taken into consideration for higher temperature applications.* Material de-rating and media compatibility factors need to be taken into consideration for higher temperature and higher pressure applications. Refer to technical catalogue 02-0142SE.* Material de-rating and media compatibility factors need to be taken into consideration for higher temperature and higher pressure applications. Refer to technical catalogue 02-0142SE.This valve has been modified for use with Hydrogen. To order, add the suffix HYG at the end of your part number.This valve has been modified for use with Hydrogen. To order, add the suffix HYG at the end of your part number.This valve has been modified for use with Hydrogen. To order, add the suffix HYG at the end of your part number.1415Medium Pressure Accessories - Autoclave Engineers ®Medium Pressure Adapters - Autoclave Engineers ®Medium Pressure Actuators - Autoclave Engineers ®Medium Pressure Tubing - MPI TM SeriesADDITIONAL RESOURCES AVAILABLE ON /IPD›WHITE PAPER - ADDRESSING THE CHALLENGE OF HYDROGEN EMBRITTLEMENT IN METALLURGY ›BROCHURE - INSTRUMENTATION SOLUTIONS FOR HYDROGEN-POWERED VEHICLESRelief Valves - Soft Seat RVS Series - Autoclave Engineers ®This valve has been modified for use with Hydrogen. To order, add the suffix HYG at the end of your part number.* Material de-rating and media compatibility factors need to be taken into consideration for higher temperature applications.1617Cryogenic/LH 2 ApplicationsComponents for cryogenic/LH 2 applications at temperatures down to -253O C (-423O F) and pressures up to 50 bar (725 psi).Designed and engineered for use with Group 1 gases, Parker Bestobell’s valves are suitable for liquid hydrogen applications requiring temperatures as low as -253O C. All valves are pressure-tested prior to dispatch.To order, add the suffix -H at the end of your part number.Globe Valves - Stainless Steel with Bronze Internals - BestobellIndustrialGlobe Valves - Stainless Steel - Bestobell MarineLift Check Valves - Stainless Steel with Bronze Internals -Bestobell IndustrialLift Check Valves - Stainless Steel - Bestobell MarineSwing Check Valves - Stainless Steel - Bestobell MarineManual Gate Valves - Stainless Steel - Bestobell IndustrialActuated Gate Valves - Stainless Steel - Pneumatic Tyre Design- Bestobell IndustrialPneumatically Actuated Globe Valves - Stainless Steel withBronze Internals - Bestobell IndustrialPneumatically Actuated Globe Valves - Stainless Steel -Bestobell MarineAppendixA-LOK® tube fittings installation for hydrogen serviceParker has an improved and optimised installation procedure for its A-LOK® parts used inhydrogen service. Please follow the steps below for correct installation.1. The tube should be fully inserted into the shoulder of the fitting until full tube abutment isachieved.2. The nut should be advanced to the finger tight position and then be marked at the 6 o’clockposition.3. The nut should then be advanced 1 ½ turns with the appropriate wrench making sure aback-up wrench is used to hold the fitting body during the tightening process.4. The mark will now be at the 12 o’clock position.Once this has been achieved, the assembly will be ready to use in your Hydrogen system.For tube specifications, ordering information, preparation and pressure ratings, please referto the Parker Fittings, Materials and Tubing Guide catalogue ref. 4190-FMTG.18194190-HYD 03/22© 2022 Parker Hannifin Corporation Parker Hannifin Manufacturing Ltd.Instrumentation Products Division, Europe Riverside RoadBarnstaple EX31 1NP United Kingdomphone 0044 1271 /ipd Worldwide Division HeadquartersEuropean Product Information Centre Free phone: 00 800 27 27 5374(from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL, IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, SK, UK, ZA)Europe, Middle East, AfricaAE – United Arab Emirates, DubaiTel: +971 4 8127100AT – Austria, St. Florian Tel: +43 (0)7224 66201 AZ – Azerbaijan, Baku Tel: +994 50 2233 458BE/NL/LU – Benelux, Hendrik Ido Ambacht Tel: +31 (0)541 585 000BY – Belarus, Minsk Tel: +48 (0)22 573 24 00CH – Switzerland, Etoy Tel: +41 (0)21 821 87 00 CZ – Czech Republic, PragueTel: +420 284 083 111DE – Germany, Kaarst Tel: +49 (0)2131 4016 0DK – Denmark, Ballerup Tel: +45 43 56 04 00ES – Spain, Madrid Tel: +34 902 330 001FI – Finland, Vantaa Tel: +358 (0)20 753 2500FR – France, Contamine s/Arve Tel: +33 (0)4 50 25 80 25GR – GreeceTel: +30 69 44 52 78 25HU – Hungary, Budaörs Tel: +36 23 885 470IE – Ireland, Dublin Tel: +353 (0)1 466 6370IL – IsraelTel: +39 02 45 19 21IT – Italy, Corsico (MI) Tel: +39 02 45 19 21KZ – Kazakhstan, Almaty Tel: +7 7273 561 000NO – Norway, Asker Tel: +47 66 75 34 00PL – Poland, Warsaw Tel: +48 (0)22 573 24 00PT – PortugalTel: +351 22 999 7360RO – Romania, Bucharest Tel: +40 21 252 1382RU – Russia, Moscow Tel: +7 495 645-2156SE – Sweden, Borås Tel: +46 (0)8 59 79 50 00SL – Slovenia, Novo Mesto Tel: +386 7 337 6649TR – Turkey, Istanbul Tel: +90 216 4997081UK – United Kingdom, Warwick Tel: +44 (0)1926 317 878ZA – South Africa, Kempton ParkTel: +27 (0)11 961 0700North AmericaCA – Canada, Milton, Ontario Tel: +1 905 693 3000US – USA, Cleveland Tel: +1 216 896 3000Asia PacificAU – Australia, Castle Hill Tel: +61 (0)2-9634 7777CN – China, Shanghai Tel: +86 21 2899 5000HK – Hong Kong Tel: +852 2428 8008IN – India, MumbaiTel: +91 22 6513 7081-85JP – Japan, Tokyo Tel: +81 (0)3 6408 3901KR – South Korea, Seoul Tel: +82 2 559 0400MY – Malaysia, Shah Alam Tel: +60 3 7849 0800NZ – New Zealand, Mt WellingtonTel: +64 9 574 1744SG – Singapore Tel: +65 6887 6300TH – Thailand, Bangkok Tel: +662 186 7000TW – Taiwan, Taipei Tel: +886 2 2298 8987South AmericaAR – Argentina, Buenos Aires Tel: +54 3327 44 4129BR – Brazil, Sao Jose dos CamposTel: +55 080 0727 5374CL – Chile, Santiago Tel: +56 22 303 9640MX – Mexico, Toluca Tel: +52 72 2275 4200Parker Hannifin CorporationInstrumentation Products Division 1005 A Cleaner Way Huntsville AL 35805 USAphone 001 (256) 881 /ipd。

海康威视网络硬盘录像机操作说明一、开箱及安装1.打开包装箱，将海康威视网络硬盘录像机取出。

2.检查包装是否完好无损，并核对配件是否齐全，包括硬盘录像机、电源适配器、鼠标、网络连接线等。

3.将硬盘录像机放置在水平稳定的台面上，并确保通风良好，避免过暖或过热的环境。

二、连接设备1.将网络硬盘录像机的电源适配器插入电源插座，并将其它设备如显示器、摄像头等连接到硬盘录像机对应的接口上。

2.使用网络线连接硬盘录像机和路由器，确保网络连接正常。

3.将鼠标连接到硬盘录像机的USB接口上。

三、启动和登录1.打开电源开关，硬盘录像机开始启动。

2.等待片刻，系统加载完成后，会出现登录界面。

3.使用鼠标点击登录界面上的“用户名”和“密码”输入框，输入正确的用户名和密码，并点击登录按钮。

四、主界面1.登录成功后，进入主界面，可以看到监控画面和相关的功能按钮。

2.主界面上方有一排功能按钮，包括“监控画面”、“录像回放”、“报警信息”等。

3.左侧是监控画面，可以显示多个摄像头的实时图像。

五、基本设置1.点击主界面上方的“设置”按钮，进入基本设置菜单。

2.在基本设置菜单中，可以进行系统设置、网络设置、存储设置等。

3.修改完设置后，点击保存按钮，系统会自动保存设置并生效。

六、监控画面1.点击主界面上方的“监控画面”功能按钮，可以查看所有已经安装的摄像头实时画面。

2.若需要单独查看一些摄像头的画面，可以点击左侧监控画面中对应的通道，即可单独查看该通道的实时画面。

3.可以通过相关按钮控制画面的放大、缩小，调整亮度、对比度等。

七、录像回放1.点击主界面上方的“录像回放”功能按钮，进入录像回放界面。

2.在录像回放界面，可以选择回放的时间段和通道，查看录像文件。

3.可以通过相关按钮控制录像的播放、暂停、快进、慢放等。

八、报警信息1.点击主界面上方的“报警信息”功能按钮，可以查看设备的报警信息。

2.报警信息会记录设备发生的报警事件，如移动侦测、遮挡报警等。

海康威视网络硬盘录像机使用手册是每一个使用该器材的用户最需要了解的一些信息，这份手册将会告诉用户如何正确地使用这款产品，包括安装，设置和使用过程中的一些注意事项。

本文将以详细的形式来介绍这款网络硬盘录像机的使用手册。

一、硬件安装在开始使用之前，我们需要先对硬件进行安装。

安装的主要步骤包括：1.将硬盘安装好。

请注意，您需要使用比较大且质量较高的硬盘，以确保其能够满足您的存储需求。

在安装好后，您需要对硬盘进行分区和格式化，才能使用它。

2.将网络硬盘录像机的视频输入/输出线缆连接至相应的摄像头和显示器上。

在连接时，请确保线缆的连接正确，以免出现视频丢失和画面不清晰等问题。

3.连接网络。

网络硬盘录像机需要连接到网络才能远程监控和管理。

您可以通过有线或无线的方式将其连接至局域网或互联网上。

4.接通电源。

将电源插头连接到设备上，并将其接通电源。

在开机后，请等待数分钟以确保设备初始化完成。

二、基本设置安装好后，您需要进行一些基本设置，以确保其能够正常工作。

这些设置包括：1.设置系统时间。

您需要设置正确的系统时间，以确保其能够正常记录和管理视频。

2.设置 IP 地址。

在网络硬盘录像机连接到网络后，您需要对其进行 IP 地址的设置，以便其他设备能够访问它。

您可以直接使用设备默认的 IP 地址，也可以根据需要进行修改。

3.设置录像模式。

网络硬盘录像机提供了多种录像模式，如手动录像、定时录像、报警录像等。

您需要根据具体需求进行设置。

4.设置录像分辨率和质量。

您可以根据需要设置录像的分辨率和质量，以达到最佳的观看效果和存储效率。

以上是基本设置，您可以根据个人需要进行设置。

如果您还需要更深入的设置和优化，您可以参考硬盘录像机使用手册进行操作。

三、使用过程中的注意事项在使用网络硬盘录像机的过程中，您需要注意以下一些事项：1.确保设备工作稳定。

网络硬盘录像机工作不稳定可能导致视频丢失和画面不清晰等问题。

请确保设备放置稳固，并避免与其他电子设备干扰。

海康威视网络硬盘录像机操作说明一、开机具体开机步骤如下：1、插上电源.2、打开后面板电源开关。

3、设备开始启动，弹出“开机”界面。

设备启动后，“电源"指示灯呈蓝色.设备启动后，可通过开机向导进行简单配置,使设备正常工作。

二、关机1、选择“主菜单→ 设备关机".进入“设备关机”面，如图。

图4.2设备关机界面2、单击“关机”，弹出提示窗口。

3、单击“是”，设备关机。

三、录像设置具体操作步骤如下：1、选择“主菜单→ 录像配置→ 计划配置”.进入“录像计划"界面，如图.2、选择要设置定时录像的通道。

3、设置定时录像时间计划表，具体操作步骤如下:选择“启用录像计划”。

说明设置完成后，该通道录像呈现7×24小时普通录像状态，如图。

若其他通道与该通道录像计划设置相同,单击“复制”,勾选上其他通道或IP通道，将该通道的设置复制给其他通道。

图定时录像完成界面4、单击“应用”,保存设置。

四、回放：常规回放即按通道和日期检索相应的录像文件，从生成的符合条件的播放条中，依次播放录像文件。

具体回放操作步骤如下:1、选择“主菜单→ 回放"。

进入“常规回放"界面，如图。

进入常规回放界面2、选择录像回放的通道,日历自动显示当前月份的录像情况。

录像信息显示界面，如图。

3、鼠标双击需要回放的日期，进入录像回放界面。

录像回放界面，如图说明最大支持16路同步回放,根据设备型号与路数的不同,回放性能不同。

可参见6技术参数.支持多路4倍速回放五、备份:快速备份可快速将录像文件备份到存储设备上。

具体操作步骤如下：1、选择“主菜单→ 备份→ 常规备份”。

进入“录像备份”界面，如图。

图录像备份界面2、选择需要备份的通道，单击“快速备份”。

进入“备份"界面，如图.。

网络视频录像机用户手册V3.01目录关于本文档 (1)1 操作必读 (2)1.1 本地操作必读 (2)1.2 本地界面操作方法 (2)2 初始配置 (5)2.1 开机准备 (5)2.2 自动添加 (5)2.3 设备登录 (6)2.4 开机向导 (9)3 预览 (11)3.1 预览界面状态 (12)3.2 窗格工具栏 (12)3.3 底部工具栏 (13)3.4 右键菜单栏 (17)4 通道配置 (20)4.1 通道管理 (20)4.1.1 IPC配置 (20)4.1.2 鱼眼配置 (27)4.1.3 高级配置 (29)4.2 编码参数 (30)4.3 音频配置 (32)4.4 抓图参数 (33)4.5 OSD配置 (34)4.6 图像参数 (35)4.7 隐私遮盖 (39)4.8 云台配置 (41)5 智能分析 (46)5.1 智能功能配置 (46)5.1.1 联动方式 (47)5.1.2 布防计划 (54)5.1.3 人脸检测 (55)5.1.4 人脸比对 (57)5.1.5 越界检测 (60)5.1.6 区域入侵 (63)5.1.7 进入区域 (65)5.1.8 离开区域 (67)5.1.9 智能运动检测 (69)5.1.11 高空抛物 (71)5.1.12 虚焦检测 (73)5.1.13 场景变更 (73)5.1.14 物品搬移 (74)5.1.15 物品遗留 (75)5.1.16 自动跟踪 (76)5.1.17 人流量统计 (77)5.1.18 人员密度检测 (78)5.2 分析器配置 (80)5.3 名单库管理 (80)5.3.1 人脸名单 (80)5.4 车辆管控 (83)5.4.1 车牌名单 (83)5.4.2 车辆报警布控 (85)5.5 智能检索 (86)5.5.1 人脸抓拍检索 (86)5.5.2 人脸比对检索 (87)5.5.3 以图搜图 (90)5.5.4 车辆检索 (93)5.5.5 行为检索 (95)5.5.6 人数统计报表 (98)5.6 智能预览 (99)6 网络配置 (104)6.1 常规配置 (104)6.1.1 网络配置 (104)6.1.2 宇视云 (105)6.1.3 DDNS (109)6.1.4 邮件 (110)6.2 平台配置 (111)6.2.1 国标服务器配置 (111)6.2.2 国标本地配置 (114)6.2.3 UNP (114)6.2.4 监管平台 (116)6.2.5 SNMP (117)6.2.6 报警上报 (119)6.2.7 视图库GA/T1400本地配置 (120)6.2.8 视图库GA/T1400服务器配置 (121)6.2.9 CDN（流分发）管理 (122)6.2.10 TMS配置 (123)6.3 高级配置 (124)6.3.1 拨号上网 (124)6.3.2 端口 (125)6.3.3 端口映射 (126)6.3.4 组播 (127)6.3.5 FTP (128)6.4 无线局域网 (130)7 系统配置 (130)7.1 基本配置 (130)7.2 预览配置 (131)7.2.1 预览配置 (131)7.2.2 高级配置 (134)7.3 时间配置 (134)7.3.1 时间配置 (134)7.3.2 时间同步 (135)7.3.3 假日配置 (135)7.4 POS配置 (137)7.4.1 POS显示配置 (137)7.4.2 POS配置 (138)7.5 串口配置 (140)7.6 用户配置 (141)7.7 安全配置 (142)7.7.1 IP地址过滤 (142)7.7.2 ONVIF认证 (143)7.7.3 802.1x (143)7.7.4 ARP防攻击 (144)7.7.5 视频水印 (144)7.7.6 安全密码 (144)7.8 热备配置 (145)8 备份 (147)8.1 录像备份 (147)8.2 图片备份 (150)9 存储配置 (153)9.1 录像计划 (153)9.2 抓图计划 (156)9.3 阵列配置 (157)9.4 硬盘管理 (161)9.5 盘组配置 (163)9.6 容量配置 (164)9.7 高级配置 (165)10 报警配置 (166)10.1 运动检测 (166)10.2 遮挡检测 (167)10.3 人形检测 (167)10.4 视频丢失 (168)10.5 输入输出 (169)10.5.1 报警输入 (169)10.5.2 报警输出 (171)10.6 热成像检测 (173)10.7 温度异常 (175)10.8 异常配置 (176)10.9 声音检测 (177)10.10 蜂鸣器 (178)10.11 门铃呼叫 (179)10.12 滞留人数告警 (179)10.13 一键撤防 (181)10.14 手动报警 (183)11 系统维护 (184)11.1 系统信息 (184)11.1.1 基本信息 (184)11.1.2 通道状态 (184)11.1.3 录像状态 (185)11.1.4 在线用户 (185)11.1.5 硬盘状态 (186)11.1.6 解码卡状态 (186)11.2 网络信息 (187)11.2.1 网络流量 (187)11.2.2 网络抓包 (187)11.2.3 网络检测 (189)11.2.4 网络状态 (191)11.2.5 网络资源统计 (191)11.2.6 PoE/交换网口状态 (192)11.3 日志查询 (192)11.4 系统备份 (194)11.4.1 系统备份 (194)11.4.2 诊断信息 (194)11.5 系统恢复 (196)11.6 自动维护 (196)11.7 系统升级 (196)11.7.1 NVR升级 (197)11.7.2 IPC升级 (198)11.8 硬盘检测 (199)11.8.1 S.M.A.R.T.检测 (199)11.8.2 磁盘检测 (200)11.9 关于我们 (200)11.10 一键收集 (201)12 回放 (201)12.1 即时回放 (202)12.2 普通回放 (202)12.3 智能回放 (204)12.4 走廊回放 (206)12.5 外部文件回放 (206)12.6 标签回放 (206)12.7 检索回放 (208)12.8 文件管理 (209)13 关机 (210)14 Web操作 (210)14.1 登录前准备 (210)14.2 登录 (211)14.3 实况 (211)14.4 回放 (212)14.5 配置 (213)14.6 智能 (214)15 附录：常见问题解答 (214)关于本文档版权声明©2022浙江宇视科技有限公司。