Hampton Gazebo 10’x12’ Assembly Instructions说明书

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The final product will be a quality piece that will go together smoothly and give years of enjoyment. Note: THIS UNIT IS HEAVY! DO NOT assemble this item alone for safety. Four people are necessary. Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which the part is used. Warnings:

1. Assembly Instructions must be followed. 2. Pegs supplied must be used to hold this gazebo in place when upright. WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.

It is not fire proof. The fabric may burn if left in continuous contact with any flame source. ASSEMBLY INSTRUCTIONS

ITEM# L-GZ215PST-5B

HAMPTON GAZEBO 10’x12’

Post A 4

Post Base B 4

Base Protector C 4

Short Beam (1) D 2

Short Beam (2) E 2

Long Beam (1) F 2

Long Beam (2) G 2

Slanting Bar

Connector H 4

Support Bar I 8

Big Top Bar J1 4

Connect Bar J2 4

Short Side Bar K 2

Long Side Bar L 2

Long Netting Bar M 4

Short Netting Bar N 4

Big Top Connector O 1

Pothook P 1

Small Top Connector Q 1

Small Top Bar R 4

Small Canopy S 1

Large Canopy T 1

Wall U 1

Mosquito Netting V 1 Parts List

Fig.1: Fit the Base protector (C) onto the Post (A), connect the Post base (B) and post (A) by using bolt (AA)

and flat washer (BB).

Fig.2: Insert Beam E (G) to Beam D (F), and fix them by using bolt (CC) and washer (BB).

Fig.3: Attach assembled beam to Post (A) by using bolt (DD) and washer (BB).

AA M6X15 bolt 8PCS

BB M6 flat washer 64PCS

CC M6X15 bolt 40PCS

DD M6X35 bolt 16PCS

Z M6 wrench 1 PC Hardware Pack 1

Fig.4: Attach Netting bar N (M) to Beam D (E, F, G) by using bolt (CC) and washer (BB).

Fig.5: Fix Support bar (I) to Beam G (D, E, F) and Post (A) by using bolt (CC) and washer (BB).

BB M6 flat washer 28 PCS

CC M6X15 bolt 4 PCS

EE M6X40 bolt 12 PCS

FF M6 nut 12PCS Hardware Pack 2

Fig.6: Insert Connect Bar (J2) to Big top bar (J1), fix them by using bolt (CC) and washer (BB).

Fig.6-1: Insert Big top bar (J1) to Big top connector (O), screw Pothook (P) to Big top connector (O).

Fig.7: Attach Connect Bar (J2) to Post (A) by using bolt (EE), washer (BB) and nut (FF).

Fig.8: Insert Short side bar (K) and Long side bar (L) to Big top connector (O).

Fig.9: Attach Side bar K (L) to Slanting bar connector (H) by using bolt (EE), washer (BB) and nut (FF).

Fig.10: Insert Small top bar (R) to Small top connector (Q), then place the Small canopy (S) on the small top and

tighten.

Fig.11: Put Large canopy (T) on the big top; do not spread it. Attach assembled small top to Big top bar (J1) by

using bolt (EE), washer (BB) and nut (FF). Then spread the Large canopy (T) and tighten.

GG Φ8X180 peg 16 PCS

HH Small plastic ring 52 PCS

II Big plastic ring 52 PCS Hardware Pack 3

`

IMPORTANT:

1. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use. 2. Some parts may contain sharp edges, wear protective gloves if necessary. At least five or more people are recommended for safe assembly. 3. Keep all children and pets away from assembly area. 4. At least 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry line or electrical wires. 5. Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightening. 6. Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will occur to the structure. Remove fabric roof and secure screen & privacy panels to poles. 7. Install on level surface. 8. This package contains small items and plastic bags that should be kept away from children. 9. Check all nuts and bolts for tightness before and during usage. Ensure that all connectors and poles are firmly secured in position fully. It is important to do so before use so as to avoid a possible collapse or damage to the item, which could also result in injury. 10. This gazebo is intended for decorative and sunshade purposes only and is not meant to withstand extreme weather conditions including high winds, torrential rain and snow. Gazebo fabric is water resistant, not water proof and may leak during exposure to precipitation. Made in China Fig.12: Hang Mosquito netting (V) to netting bar N (M) by using Small plastic ring (HH). Fig.13: Hang Wall (U) to beam (F, D, E, G) by using Big plastic ring (II). Fig.14: Lift Base protector (C), fix assembled gazebo with Peg (GG). Now, your Gazebo is ready for use.