LWG-360 NOVO电子尺

0-320-游标万能角度尺-使用说明书游标角度尺（0-320°2′）使用说明书在机械制造过程中及计量仪器校准中，有许多带角度的工件需要测量，而测量角度的方法与量具有多种多样的选择，使用游标万能角度尺来测量工件角度是比较方便的，如（图A ）所示。

图A一、读数方法①先读度数：被游标尺零刻线所指的主尺上刻线是表示被测工件测量角的度数。

② 读分数：与主尺上刻线重合的游标尺上刻线是被测工件测量角的分数。

③ 相加求得测量值：将被测工件测量角的度数与分数相加起来，即为被测角度值。

二、结构与用途游标万能角度尺的结构如（图A ）所示。

角尺和直尺在卡块的作用下分别固定于扇形板部件和角尺上，当转动卡块上的螺帽时，即可紧固或放松角尺或直尺，在扇形板部件的后面有一与齿轮杆相连接的手把，而该齿轮杆又与固定在主尺上的弧形齿板相啮合这个就是微动装置。

当转动微动装置就能使主尺和游标尺作细微的相对移动，以精确地调整测量值，但当把制动头上的螺帽拧紧后，则扇形板部件与主尺被紧固在一起，而不能有任何相对移动。

游标万能角度尺主要用于测量各种形状工件与样板的内、外角度以及角度划线。

主尺直角尺游标基尺制动头扇形板卡块直尺三、使用和注意事项1、零值检查：使用前将游标万能角度尺擦拭干净，检查各部分相互作用是否灵活可靠，然后移动直尺使其与基尺的测量面相互接触，直到无光隙可见为止。

同时观察主尺零刻线与游标零刻线是否对准；游标尺的尾刻线与主尺相应刻线是否对准，如对准便可使用，不对准则需要调整。

2、测量0°～50°之间的角度时，被测工件放在基尺和直尺的测量面之间，如图（B-4）所示。

3、测量50°～140°之间的角度时，把角尺取下，将直尺换在角尺位置上，把被测工件放在基尺和直尺的测量面之间，如图（B-1），（B-2）所示。

4、测量140°～230°之间的角度时，把直尺取下换上角尺，但要把角尺推进去，直到角尺上短边的90°角尖和基尺的尖端对齐为止，然后把角尺和基尺的测量面靠在被测工件的表面上进行测量，如图（B-3），（B-5）所示。

电子尺使用方法
电子尺是一种用于测量长度和距离的便捷工具，它具有数字显示和高精度的特点，广泛应用于工程测量、建筑设计、家居装修等领域。

正确的使用方法能够确保测量结果的准确性和稳定性，下面将介绍电子尺的使用方法。

1. 打开电子尺，首先，按下电子尺上的开关按钮，等待数秒钟直到屏幕显示出
数字。

有些电子尺可能需要按住开关按钮一段时间才能打开，根据具体型号来操作。

2. 设置单位，大多数电子尺都支持不同的长度单位，比如厘米、英寸、毫米等。

在进行测量之前，根据需要选择合适的单位，通常可以通过按压单位按钮来进行切换。

3. 进行测量，将电子尺的测量端对准需要测量的物体，确保测量端与物体表面
紧密接触。

然后，轻轻地将电子尺沿着物体表面滑动，直到测量端到达另一端。

此时屏幕上会显示出测量结果，如果需要记录，可以按下“保持”按钮来锁定结果。

4. 零点校准，在使用电子尺之前，有时需要进行零点校准，以确保测量的准确性。

大多数电子尺都具有零点校准功能，具体操作方法可以参考使用说明书。

5. 关闭电子尺，在使用完毕后，及时关闭电子尺以节省电量，一般来说，长按
开关按钮即可关闭电子尺。

6. 保养与存放，定期清洁电子尺的表面和测量端，避免灰尘和杂物影响测量精度。

另外，在存放电子尺时，应该放置在干燥通风的地方，避免受潮或受到其他不利影响。

总结，电子尺作为一种现代化的测量工具，使用起来相对简单方便，但在实际
操作中仍需注意一些细节，比如单位选择、零点校准等。

正确的使用方法能够提高测量的准确性和效率，希望以上介绍能够帮助到您。

多用途扭矩传感器用供电、放大显示器型号：GMV2●Tool Testing 扭力工具测试●Production Supervising 生产过程监控●Documentation conforming to DIN EN ISO 9001 DIN EN ISO 9001认证●Quality Assurance 质量保证●Test Bench Evaluation 评估测试装置说明:GMV2是一款由CPU控制的供电、显示放大器，适合各种类型的扭矩测量应用，既可以在实验室作为测试装置仪表，也可工业应用为螺栓拧紧控制仪表。

连接不同类型的传感器，可以测量、显示和储存扭矩、角度、速度和功率值，还可以预设极限开关量。

使用自带说明的菜单，通过简单的步骤就可实现仪表的操作。

专用的扭矩传感器带有内置的识别芯片，当传感器和GMV2 连接后，传感器的数据会自动地被仪表识别并进行参设定。

为了更好地区别各种参数和数据的设定，我们对他们命名，或者选用条形码扫描器来完成数据设定的命名，对常规设定的访问可以设置3级密码。

测试值将在仪表的存储器中按数据/时间格式保存，这些数据可以在外部打印机上打印，或传输到数据处理设备。

通过控制输入信号( control inputs),能够实现对仪表的外部控制。

限位开关量信号用于光电信号（转角/转速）的取值触发，或用于切断电动扭矩螺丝刀的电源。

根据客户的要求还可以定制其他的功能。

标准配置:●储存1000个测量值；●50不同的测量程序；●多种语言的自带说明菜单；●3级密码用于设定的保护；●根据传感器的内置芯片, 自动识别并进行参数设定检查；●扭矩、转速和功率的测试；●循迹模式：- 可调滤波用于扭矩和转速测试；- 功率测试范围：1 mW...20,000 kW；- 测量值连续输出或周期储存；●正向或反向峰值储存模式：- 测量值的状态显示；- 用于脉冲扭力工具的可调修正系数；- 具有扭矩平均值监控功能，可调节变化的平均值●可调的消除时间(erasing time)和抑制时间(suppression time)；●用于扭矩扳手的特殊测试模式；●RS232接口，最大波特率19200；●EMC 密封外壳；●电源：230V可选附加配置:●进行参数设置的外部选件；●通过条形码扫描仪的输入；●外部控制进行储存、清除和打印；●转角测试；●对带独立电源的电动螺丝刀进行控制；●扭矩信号的模拟量输出；●交流电源和内置充电电池，8小时电池操作；●输出至Digimatic Mini-Processor打印机；●通过数据传输软件GMV2-PC-Trans，数据转化为MS-Excel客户定制参数变量0不带选项 [在扭矩-转速测试装置中,]1带数字打印机输出 [仅适用于扭矩值的打印。

WideRlus温度控制仪使用说明书widerlus智能数字控制仪使用说明书（香港尚润精密仪器有限公司）wp系列显示控制仪使用于各种温度、压力、液位、速度、长度、流量等的测量控制。

采用微处理器进行数学运算，可对各种非线性信号进行高精度的线性矫正。

灯柱显示控制器集数字测量显示和模拟显示于一体，采用数字LED显示，能准确显示和控制实时测量值；同时采用高精度101线光柱显示，清晰直观地显示实时测量值（类似模拟表显示）。

可切换输入多种分度号。

采用先进的无跳线技术，更改输入分度号时，不用更改跳线或开关。

整个仪表改型过程不需要断电。

支持多机通讯，可选择多种通讯接口方式，通讯波特率仪表内部参数自由设定。

一、主要技术参数：输入信号：模拟量热电偶：标准热电偶-B、s、K、e、J、t、wre电阻：标准热电阻-PT100、cu50或远程压力电阻电流：0~10mA、4~20mA、0~20mA等-输入电阻≤ 250电压：0~5V、1~5V、MV等-输入阻抗≥ 250K测量范围：-1999~9999字测量精度：0.2%fs±1字或0.5%fs±1字分辨率：1、0.1、0.01或0.001字温度补偿：0~50℃显示模式：-1999~9999测量值显示-1999~9999设定值显示0~100%测量值灯柱显示。

发光二极管工作状态显示光柱精度：光柱显示精度为1%。

控制模式：位型开/关回差输出信号：模拟量输出：dc0~10ma(负载电阻≤750)dc4~20ma(负载电阻≤500)dc0~5v(输出电阻≤250)dc1~5v(输出电阻≤250)开关量输出：继电器控制输出——继电器开/关返回的差值。

触电容量：AC220V/3A；DC24/6A（电阻负载）可控硅控制输出―scr（可控硅过零触发脉冲）输出，可触发可控硅：400v/100a固态继电器输出―ssr（固态继电器控制信号）输出，5~24v/30ma通讯输出：接口模式-标准串行通信接口：RS-485、RS-232C、RS-422等的波特率-300~9600bps内部自由设置馈电输出：DC24V，负载≤ 30mA控制或报警模式：可选择2~4限控制或报警，led指示。

Wireless Thermometermodel 00606CONTENTS Unpacking Instructions (2)Package Contents (2)Product Registration (2)Features & Benefits (3)Setup (4)Install or Replace Batteries (4)Set the Time & Units (5)Placement Guidelines ............. 6 Using the Thermometer.. (7)Troubleshooting (8)Care & Maintenance (9)Specifications (9)FCC Information (9)Customer Support (10)Warranty (10)Questions? Contact Customer Support at (877) 221-1252 or visit Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.Unpacking InstructionsRemove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove.Package Contents1. Display unit2. Outdoor sensor3. Instruction ManualSETºF/ºCMAX MIN+111312DISPLAY UNIT1. Current Outdoor Temperature2. Clock3. Current Indoor Temperature4. “°F/°C” Button Toggle between °F and °C.5. “SET” Button For clock setup.6. “+” Button For clock setup.7. “MAX/MIN” Button Press to view the lowest/highest temperature recorded since midnight.8. Display Low Battery Indicator 9. Outdoor Sensor Signal Strength 10. Outdoor Sensor Low Battery Indicator OUTDOOR SENSOR11. Integrated Hanger for easy placement.12. Wireless Signal Indicator Flashes when data is being sent tothe display unit.13. Battery Compartment CoverInstall or Replace BatteriesAcuRite recommends high quality alkaline batteries for the best product performance. Heavy duty or rechargeable batteries are not recommended. The outdoor sensor requires lithium batteries in low temperature conditions. Cold temperatures can cause alkaline batteries to function improperly. Use lithium batteries in the outdoor sensor for temperatures below -4ºF / -20ºC.Outdoor Sensor1. Slide off the battery compartmentcover.2. Insert 2 x AA batteries into thebattery compartment, as shown.Follow the polarity (+/-) diagram inthe battery compartment.3. Replace the battery cover.Display Unit1. Slide off the battery compartmentcover.2. Insert 2 x AAA batteries into thebattery compartment, as shown.Follow the polarity (+/-) diagram inthe battery compartment.3. Replace the battery cover.batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fre, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.Set the TimePress and hold the “SET” button for 3 seconds to enter the SET mode. Once in SET mode, the preference you are currently setting will blink on the display. To adjust the currently selected (flashing) item, press the “+” button.To save your adjustments, press and release the “SET” button again to adjust the next preference. The preference set order is as follows:CLOCK (12 or 24 hours)CLOCK HOURCLOCK MINUTEYou will automatically exit SET mode if no buttons are pressed for 30 seconds. Enter SET mode at any time by pressing and holding the “SET” button for 3 seconds.Select Degrees Fahrenheit or CelsiusTo select between degrees Fahrenheit (ºF) or Celsius (ºC) temperature units, press the “ºF/ºC” button located on the display.Placement for Maximum AccuracyAcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of both the display unit and outdoor sensor are critical to the accuracy and performance of this product.Display Unit PlacementPlace the display unit in a dry area free of dirt and dust. Displayunit stands upright for tabletop use or is wall-mountable.Outdoor Sensor PlacementSensor must be placed outside to observe outdoor conditions.Sensor is water resistant and is designed for general outdooruse, however, to extend its life place the sensor in an areaprotected from direct weather elements.Hang the sensor using the integrated hang holes or hanger, orby using string (not included) to hang it from a suitable location,like a well covered tree branch. The best location is 4 to 8 feetabove the ground with permanent shade and plenty of fresh airto circulate around the sensor.Important Placement Guidelines•To ensure accurate temperature measurement, place units out of direct sunlight and away from heat sources or vents.•Display unit and outdoor sensor must be within 165 ft (50 m) of each other. •To maximize wireless range, place units away from large metallic items, thick walls, metal surfaces, or other objects that may limit wireless communication. •To prevent wireless interference, place both units at least 3 ft (.9 m) away from electronic devices (TV, computer, microwave, radio, etc.)(165 feet maximum)(50 meters)Setup is CompleteThe sensor will now synchronize with the display unit. It may take a few minutes for synchronization to complete. Please refer to the troubleshooting section of this manual if anything appears to be functioning improperly.Using the ThermometerHigh/Low RecordsToday’s high and low values are recorded for indoor and outdoor temperature. The high and low records automatically clear at 12:00am.To view the LOW temperature record, press and release the “MAX/MIN” button. The “MIN” icon appears on the display next to the low records.To view the HIGH temperature record, press and release the “MAX/MIN” button. The “MAX” icon appears on the display next to the high records.To reset the LOW records, press AND HOLD the “MAX/MIN” button while viewing the low records. Dashes will display to confirm all low values have been cleared.To reset the HIGH records, press AND HOLD the “MAX/MIN” button while viewing the high records. Dashes will display to confirm all high values have been cleared.TroubleshootingIf your AcuRite product does not operate properly after trying the troubleshooting steps, visit or call(877) 221-1252 for assistance.Care & MaintenanceDisplay Unit CareClean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away from dust, dirt and moisture. Clean ventilation ports regularly with a gentle puff of air.Outdoor Sensor CareClean with a soft damp cloth. Do not use caustic cleaners or abrasives. SpecificationsTEMPERATURE RANGE Outdoor: -40ºF to 158ºF; -40ºC to 70ºCIndoor: 32ºF to 122ºF; 0ºC to 50ºCWIRELESS RANGE 165 ft / 50 m depending on home construction materials WIRELESS FREQUENCY 433 MHzPOWER Display: 2 x AAA alkaline batteriesSensor: 2 x AA alkaline or lithium batteriesDATA REPORTING 30 second updatesFCC InformationThis device complies with part 15 of FCC rules. Operation is subject to the following two conditions:1- This device may NOT cause harmful interference, and2- This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) This device must accept any interference received, including interference that may cause undesired operation of the device.Customer SupportAcuRite customer support is committed to providing you with best-in-class service. For assistance , please have the model number of this product available and contact us in any of the following ways:(877) 221-1252 ********************24/7 support at www.AcuRite .com► Installation Videos ► Register your Product ► Instruction Manuals ► Support User Forum ► Replacement Parts► Submit Feedback & IdeasLimited One Year WarrantyAt AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase.We recommend that you visit us at for the fastest way to register your product. However, product registration does not eliminate the need to retain youroriginal proof of purchase in order to obtainwarranty benefits. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free ofdefects when properly installed and operated for a period ofone year from the date of purchase. Remedy for breach of thiswarranty is limited to repair or replacement of the defectiveitem(s). Any product which, under normal use and service, isproven to breach the warranty contained herein within ONEYEAR from date of sale will, upon examination by Chaney,and at its sole option, be repaired or replaced by Chaney.Transportation costs and charges for returned goods shallbe paid for by the purchaser. Chaney hereby disclaims allresponsibility for such transportation costs and charges. Thiswarranty will not be breached, and Chaney will give no credit for products it manufactures which have received normal wear and tear, been damaged (including by acts of nature), tampered, abused, improperly installed, damaged in shipping, or repaired or altered by others than authorized representatives of Chaney.The above-described warranty is expressly in lieu of all other warranties, express or implied, and all other warranties are hereby expressly disclaimed, including without limitation the implied warranty of merchantability and the implied warranty of fitness for a particular purpose. Chaney expressly disclaims all liability for special, consequential or incidental damages,whether arising in tort or by contract from any breach of thiswarranty. Some states do not allow the exclusion or limitationof incidental or consequential damages, so the above limitation or exclusion may not apply to you. Chaney further disclaims all liability from personal injury relating to its products to the extentpermitted by law. By acceptance of any of Chaney’s products, the purchaser assumes all liability for the consequences arisingfrom their use or misuse. No person, firm or corporation is authorized to assume for Chaney any other liability in connection with the sale of its products. Furthermore, no person, firm or corporation is authorized to modify or waive the terms of this paragraph, and the preceding paragraph, unless done in writing and signed by a duly authorized agent of Chaney. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. For in-warranty claims: Chaney Instrument Co. 965 Wells St., Lake Geneva, WI 5314711Weather Temperature Weather Kitchen Clocks Stations & Humidity Alert Radio Thermometers& TimersIt’s more than accurate, it’sAcuRite offers an extensive assortment of precision instruments, designed to provide you with information you can depend on toPlan your day with confidence™.© Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of theChaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights Printed in China are the property of their respective owners. AcuRite uses patented technology. 00606 INST 033014 Visit /patents for details.。

PLC/DCS-driven calibration of precision scales2I N D 360b a s e A u t o m a t i o n T e r m i n a lTechnical FeaturesIND360 Automation TerminalParameter Detail Units ofMeasurementDINPanelHarshHousingEnclosure typeDIN-Rail mount,quick connection with automatic grounding Panel mount with detachable electronicsVESA 100 Desk/wall/column mountMaterialRugged ABS plasticStainless steel front panel with hygienic drip edge including mounting hardware Stainless steel, includes fixed-angle brackets Ingress protection IP20, Type 1IP65 display, IP20 electronicsIP66 and IP69KW × H × D mm / in 40 × 130 × 100 / 1.6 × 5.1 × 3.9175 × 94 × 16 / 6.9 × 3.7 × 0.6275 × 85 × 200 / 10.8 × 3.3 × 7.9Shipping weight kg / lb 0.5 / 1.11.7 / 3.73.6 / 7.9Legal for Trade °C / °F -10 to 40 / 14 to 104; 10% to 90% relative humidity, non-condensing Operation °C / °F -10 to 50 / 14 to 122; 10% to 90% relative humidity, non-condensing Storage°C / °F -40 to 60 / -40 to 140; 10% to 90% relative humidity, non-condensing PowerRequirementsDC poweredVDC / W20 - 28VDC 1 / 12W 2NA1 Power supply short circuit protection time shall be equal or longer than 100ms.218W, when 5 to 8 POWERCELLs are connectedAC poweredVAC / Hz NA 100 - 240 VAC / 49 - 61 Hz Power Dissipation DC powered W 3 4.5NA AC powered WNA 66ScaleNumber of scales 1Strain gauge (analog) type Max. 8× 350Ω (20× 1,000Ω) load cells; 1-4mV/V sensitivity; 5VDC excitation voltageμV buildrecommended / approved 0.1 μV/d recommended; 0.3 μV/e Weights and Measures approvedPOWERCELL ® type Supports one PowerDeck TM floor scale or a network of up to 8 POWERCELL ® load cells, or PowerMount TM weigh modulesPrecision type Precision scales and weigh modules – see Precision Scale Compatibility on page 6Adjustment / calibration Zero / span with linearization up to 5 points; step; CalFree (analog scale) / CalFree Plus (POWERCELL ® scale)Primary unit Analog/POWERCELL ®: g, kg, lb, t and tonPrecision: Determined by scale or weigh module Calibration unit Analog/POWERCELL ®: g, kg, lb, t and ton Precision: Determined by scale or sensorCapacity & incrementAnalog/POWERCELL ®: 1,000,000 maximum Capacity, maximum 100,000 display incrementsPrecision: Determined by scale or or sensorConnectivityAutomation interface Optional: EtherNet/IP , Profibus DP®, PROFINET®, Modbus RTU, or Analog Output (4-20 mA/0-10V, 16-bit resolution)Redundancy Media Redundancy Protocol (MRP - Siemens) and Device Level Ring (DLR - ODVA)Protocol Standard Automation Interface (SAI) 2 and 8 block format Protocol type 32-bit floating point and binary; cyclical or acyclicalSimultaneous floating point variables 1 or 7 user-selectable including status block for condition monitoringAlarm status Smart5TM based on NAMUR NE107Condition monitoring Heartbeat, Data OK, Smart5TMAutomation Bus driv-ers - Siemens GSD (Profibus DP), GSDML (PROFINET), function block Certification Profibus DP / PROFINETProfibus international Certificate No: Z02266, Z13050, Z13051Technical Features ContinuedIND360 Automation Terminal34I N D 360b a s e A u t o m a t i o n T e r m i n a lOrdering InformationIND360 Automation TerminalsIND360 is available in different variants with the main item number 30601194.Choose options according to the variant configuration structure, and contact your METTLER TOLEDO Sales representative for detailed ordering information.6 - PowerMount 8 - Precision - APWC - 5in8out (Solid State)R - Profibus DP (Vertical Header)Ordering InformationIND360 Automation TerminalsBase Unit DescriptionsItem Number IND360 in different enclosures30601194IND360 DIN MountIND360 Panel MountIND360 HarshSmart Options1 = None (analog scale)4 = Precision (PBK, PFK) - Standard Industrial (approved readability and M12 connector on terminal side)5 = PowerDeck M12 (connector on terminal side)6 = PowerMount (open wires on terminal side)8 = Precision - APW incl. PBK, PFK (higher readability and open wires on terminal side)Input/Output Options0 = NoneA = Analog output (4 - 20mA)B = Analog output (4 - 20mA) plus 3 digital inputs / 4 digital outputs (solid state)C = 5 digital inputs / 8 digital outputs (solid state)Connectivity Options0 = NoneI = Industrial Ethernet (PROFINET or EtherNet/IP)M = Modbus RTUR = Profibus DP (vertical header - connector)Application Options0 = BaseT = Tank vesselPower Options1 = AC (AC/DC power module included)3 = DCAccessoriesItem Number Descriptions306011494-20mA analog output PCBA kit for IND360 DIN and Panel mount version including enclosure opening tool306011504-20mA analog output PCBA kit for IND360 Harsh version30601151PCBA kit of 4-20mA analog output, 3 discrete inputs, 4 discrete outputs (solid state) for IND360 DIN and Panel mount version including enclosure opening tool30601152PCBA kit of 4-20mA analog output, 3 discrete inputs, 4 discrete outputs (solid state) for IND360 Harsh version30601153PCBA kit of 5 discrete inputs, 8 discrete outputs (solid state) for IND360 DIN and Panel mount version including enclosure opening tool30601154PCBA kit of 5 discrete inputs, 8 discrete outputs (solid state) for IND360 Harsh version30601155PCBA kit of Industrial Ethernet connection (PROFINET or EtherNet/IP) for IND360 DIN and Panel mount version including enclosure opening tool30601156PCBA kit of Industrial Ethernet connection (PROFINET or EtherNet/IP) for IND360 Harsh version30601159PCBA kit of Modbus RTU connection for IND360 DIN and Panel mount version including enclosure opening tool30601160PCBA kit of Modbus RTU connection for IND360 Harsh version30601161PCBA kit of Profibus DP connection for IND360 DIN and Panel mount version including enclosure opening tool30601162PCBA kit of Profibus DP connection for IND360 Harsh version30617714AC/DC Power Module APS32430617716Power supply cable from the APS324 power module to IND36030624028Complete set of IND360 connecters.30624029Display cable (3m) from IND360 module to the panel. Use this when the IND360 module is not mounted to the back of the panel. 30624030Display cable (11cm) from IND360 module to the panel. Use this when the IND360 module is mounted to the back of the panel. 30462051VESA 100 Bracket to mount a IND360 Harsh version on desk or on wall22020286Adjustable Column Bracket VESA 100 for IND360 Harsh version30624077Opening tool for IND360 DIN mount version enclosure5For more information/IND360METTLER TOLEDO Group Industrial DivisionLocal contact: /contactsSubject to technical changes©02/2021 METTLER TOLEDO. All rights reserved Document No. 30531752 A MarCom IndustrialWeighing EquipmentActuatorsPLC/DCSPrecision Scale CompatibilityIND360 Automation TerminalsConnection DrawingsIND360 Automation TerminalsIND360 Precision connects to many types of precision weigh modules. The following table lists how various functions are supported when different types of weigh modules or scales are connected.IND360 connects many different types of weighing equipment to automation controls such as PLCs or DCSs. It provides the ability to manage weighing applications that directly drive outputs for actuators and receive inputs from switches - see IND360 manuals for more details. IND360 is very easy to setup using the web interface that is accessed via a web browser such as Microsoft Edge or Google Chrome. When cloud connectivity is desired, choose the METTLER TOLEDO ACI400.All relevant documentation, software, device description files, and sample code are available at:/ind-IND360-downloadsPrecision Scales for Legal-for-TradePrecision Scales for AutomationCompatible Modules PBD555 / PBD769 / PBD655 / PBK785 / PBK9 / PTA4XX / PFA5XX / PUA5XX / PFA779lift / PFK9WKC / WMS / WXS / SLF6 / PBK989-APW / PFK989-APW Basic Functions:Read weight and status, tare, zero, clearDisplay/keypad Display/keypad Web interface Web interface Automation interfaceAutomation interface Parameter configuration:e.g. calibration, adjustment, filter parameters Display/keypad on Panel and Harsh versionsDisplay/keypad Software tool: APW-Link Automation interface 1Firmware upgrade for precision modulesSoftware tool: eloader Software tool: eloader1Each weigh module supports different functions. Please consult the SAI (Standard Automation Interface) manual for further details.。

M8126用户手册声明本文件版权归南宁宇立仪器有限公司（以下简称宇立仪器）所有，文件所包含的信息其知识产权归宇立仪器所有，任何单位和个人不得抄袭或用于其它商业活动。

本文件适用的对象为宇立仪器生产的数据采集卡M8126，该采集卡用于6轴力传感器的信号采集。

宇立仪器保留对该文件最终解释及更新的权利，使用前请认真阅读该手册，如有疑问，请及时联系我公司，以免造成损失。

目录1.概述 (3)2.参数配置 (4)1 (4)2.1 I DAS RD软件 (4)2.2 指令调试 (4)2.3 显示实时曲线 (5)3.电源线缆、接头定义及指示灯状态 (6)3.1 电源线缆 (6)3.2 接头定义 (6)3.2.1 19针雷莫接头 (6)4.2.2 通信接头 (7)3.3 指示灯 (7)4.指令系统 (8)4.1 SFWV查询软件版本 (8)4.2 DCPM配置解耦矩阵 (8)4.3 DCPCU解耦数据计算单位 (8)4.4 SMPF设置系统采样率 (9)5.传感器解耦运算 (9)5.1 矩阵解耦的传感器 (10)5.2 结构解耦的传感器 (10)5.3 其他传感器 (11)M8126是SRI多轴力传感器的信号处理器，能够提供激励、对信号进行放大、调理、A/D转换、通过EtherCAT、RS232与主机进行通信。

性能描述：•模拟–6通道–可编程的增益–可编程的去除零点偏移–低噪声的仪表放大•数字–总线：EtherCAT、RS232通信–24位sigma-delta ADC–采样率:10~2kHz–分辨率:1/5000 to 1/10000满量程•面板信息–模拟接口:LEMO FGG.2B.319.CLAD52Z–数字接口: RJ45(EtherCAT)、DB-9 (RS232)–供电:12V to 36V，200mA. 电源线缆直径3.5mm长2m–电源以及状态指示灯•软件–iDAS RD：调试软件，显示实时采样曲线–设备描述文件(*.xml)，直接与EtherCAT设备通信2. 参数配置M8126 出厂时参数已经配置好，可以通过xml 文件直接接入EtherCAT 网络。

3X360R, 3X360GThree Plane LasersUsers Manual09/2020© 2020 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.LIMITED WARRANTY AND LIMITATION OF LIABILITYThis Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that Service Center with a description of the problem.THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you.Fluke Corporation Fluke Europe B.V. ООО «Флюк СИАЙЭС»P.O. Box 9090 P.O. Box 1186 125167, г. Москва,Everett, WA 98206 5602 BD Eindhoven Ленинградский проспект дом 37,U.S.A. The Netherlands корпус 9, подъезд 4, 1 этаж11/99Table of ContentsTitle Page Introduction (1)How to Contact Fluke (1)Safety Information (1)Product Familiarization (3)Features (3)Lasers and Optical Glass (4)Controls (5)Check Product Accuracy (6)Cone Accuracy (6)Horizontal Leveling Accuracy (8)Vertical Accuracy (10)90 Degree Accuracy (12)Accessories (14)3X360 Magnetic L-bracket (14)Maintenance (15)Clean the Product (15)Replacing Battery (15)RBP5 Rechargeable Battery (16)Housing Glass Insert (16)Specifications (17)3X360R, 3X360G Users Manual3X360R, 3X360GIntroduction IntroductionThe 3X360R, 3X360G Three Plane Lasers (the Product) are battery powered, self-leveling, professional grade instruments. The 3X360R emit solid red line lasers. The 3X360G emit solid green line lasers. The 3X360R and 3X360G also emit vertical and horizontal point lasers 90 degrees from the Product. Use the Product to lay out reference points to align targets horizontally, vertically, or diagonally.NoteIf the laser beam is difficult to see, use either the XLD+ or SLDR or SLDG Laser Detector to accurately determine the location of the laser. See the XLD+ or SLDR or SLDG Users Manual.How to Contact FlukeTo contact Fluke, call one of the following telephone numbers:• Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)• Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)• Canada: 1-800-36-FLUKE (1-800-363-5853)• Europe: +31 402-675-200• Japan: +81-3-6714-3114• Singapore: +65-6799-5566• China: +86-400-921-0835• Brazil: +55-11-3530-8901• Anywhere in the world: +1-425-446-5500Or, visit the PLS website at .To view, print, or download the latest manual supplement, visit .Safety InformationA Warning identifies conditions and procedures that are dangerous to the user. A Caution identifies conditions and procedures that can cause damage to the Product or the equipment under test.To prevent eye damage and personal injury:• Read all safety information before you use the Product.• Carefully read all instructions.• Do not alter the Product and use only as specified, or the protection supplied by the Product can be compromised.• Do not use the Product if it operates incorrectly.• Do not use the Product if it is altered or damaged.• Use the Product only as specified or hazardous laser radiation exposure can occur.• Do not look into the laser. Do not point laser directly at persons or animals or indirectly off reflective surfaces.• Do not look directly into the laser with optical tools (for example, binoculars, telescopes, microscopes). Optical tools can focus the laser and be dangerous to the eye.• Do not open the Product. The laser beam is dangerous to eyes.• Battery contains hazardous chemicals that can cause burns or explode. If exposure to chemicals occurs, clean with water and get medical aid.• Do not disassemble the battery.• Repair the Product before use if the battery leaks.• The battery door must be closed and locked before you operate the Product.• Remove the battery if the Product is not used for an extended period of time, or if stored in temperatures above 50 °C.If the battery is not removed, battery leakage can damage the Product.• Replace the battery when the low battery indicator shows to prevent incorrect measurements.• Use only Fluke approved power adapters to charge the battery. Refer to RBP5 manual for additional safety information and instructions.• Do not short the battery terminals together.• Do not disassemble or crush battery cells and battery packs.• Do not keep cells or battery in a container where the terminals can be shorted.3X360R, 3X360GUsers ManualTable 1 is a list of the symbols that can be used on the Product or in this manual.Table 1. SymbolsNoteIn colder climates, the Product needs sufficient time to warm up to achieve the stated accuracy measurements. Turn on both the horizontal and vertical lasers and wait 3 minutes before you take a measurement. When you move the Product between environments with large differences in ambient temperature, allow for an additional adjustment time.3X360R, 3X360GProduct Familiarization Product FamiliarizationThe manual explains features for multiple models. Because models have different features and accessories, not all of the information in the manual may apply to your Product.FeaturesUse Table 2 to identify the features and standard accessories of your Product.Table 2. FeaturesIn3X360R, 3X360GControls ControlsTable 4 lists the Controls of the Product.3X360R, 3X360GUsers ManualCheck Product AccuracyCone Accuracy1. Place the laser on a flat surface going in one direction.2. Turn on the horizontal beam and project on the parallel wall. You will need to have a set distance between (a,b)which will be referred to as "D" with the horizontal beam.illustration 1illustration 23. Rotate the laser 180 degrees horizontally and place at point b, as seen above .4. Turn on the horizontal beam and adjust the laser height so the center of the beam is aligned with mark b.3X360R, 3X360GCone Accuracyillustration 35. Mark c directly above or below a.6. Measure the distance between these two marks (a,c). If the measurement value is greater then the corresponding E value, take to your service provider.73X360R, 3X360GUsers ManualHorizontal Leveling AccuracyIt is important to conduct an accuracy check at the expected working distance for the specific use case and is illustrated in Table 6.1. Place the laser on a flat surface going in one direction. You will need to have a set distance between (a,b) which will bereferred to as "D".2. Turn on the horizontal beam and mark (a,b)a is 3.2ft (1m) away from laserillustration 13. Once “D” is identified based on illustration 1, rotate the laser 90 degrees horizontally as seen below.4. Mark c and calculate the distance between c,b and this is F.illustration 2893X360R, 3X360GHorizontal Leveling Accuracy5. Rotate the laser 180 degrees horizontally as seen below.6. Mark d and calculate the distance between d,b and this is E.illustration 37. Rotate the laser 270 degrees horizontally as seen below.8. Mark e and calculate the distance between e,b and this is G.9. If any of the values are greater than the respective E,F,G column values, take to your service provider.illustration 4103X360R, 3X360G Users ManualVertical AccuracyIt is important to conduct an accuracy check at the expected working distance for the specific use case and is illustrated in Table 7.1. Place the laser on a flat surface that is even in both directions across.a.The height of the room used should reflect with the corresponding values under column "J"illustration 13X360R, 3X360GVertical Accuracy2. Turn on both vertical beams +a. Mark two short lines where both vertical beams intersect on points (a,b) and (c,d).illustration 23. Pick up and rotate the laser 180 degrees then position the vertical beams with existing (a,b) marks. These marks on the ground become (e,f).4. On the ceiling, mark two short lines (g,h)illustration 35. Measure the distance between (h,d) and this value is K.6. Measure the distance between (c,g) and this value is L7. Review your applicable row for vertical distance is less than or equal to K & L. If greater than the values, take to your service provider.1190 Degree AccuracyChecking 90 degree accuracy requires a large open floor space. Distances A,B,C can be chosen based on your application and distance to use.1. Place the laser on a smooth, flat and stable surface that is level in both directions.2. Turn on the side vertical beam.3. Mark the center of the beam at three locations on the ground, as seen below at (a,b,c) and (b) should be the midpointof the entire line length.illustration 14. Move the laser to mark b and turn on both vertical beams +5. Position the beam crossing precisely at mark b.6. Mark location d along the front vertical beam at set distance C.illustration 2127. Rotate the laser 90 degrees horizontally8. Position the front and side vertical beams with (b).9. Mark e and measure the distance (D) beweetn (c,e).10. If the value is greater than D values, take to your service provider.illustration 3133X360R, 3X360GUsers ManualAccessoriesTable 9 is a list of the accessories available for the Product.Table 9. AccessoriesModel Description PN PLS HGI3X360R PLS Housing glass insert for PLS 3x360R5204916 PLS HGI3X360G PLS Housing glass insert for PLS 3x360G5214800 PLS 3X360 MLB Magnetic L-bracket w/ micro and elevation adj5214817 PLS 3X360 CB Ceiling bracket used w/ PLS 3X360 MLB5214821 PLS XLD+PLS Universal rotary/line laser detector w/ clamp5221059 PLS 3X360 HC PLS 3X360 blow mold hard case5221067 PLS RBP5Li-ion battery for handheld lasers w/ charging cord5023322 PLS RRT4Red magnetic reflective target5022629 PLS GRT4Green magnetic reflective target5022634 Note: PLS 3X360 is not compatible with PLS BP5 alkaline battery pack (PN 5031952)3X360 Magnetic L-bracket and Ceiling BracketPLS 3X360 CBFigure 13X360 MLB Magnetic L-bracketHorizontal rotation360◦Horizontal rotation precision adjustment YesElevation adjustment Max. 2.79 in (71 mm)Elevation adjustment lock*YesLaser level mounting screw1/4-20 UNC male threadedTripod mounting hole1/4-20 UNC female threaded, 5/8-11 UNC female threaded Wall hanging hole Max. 0.53 in (13.5 mm)Dimensions (H x W x D)Approx. 5.9 x 3.3 x 5.4 in (150 x 87.3 x 137 mm) Weight Approx. 0.86 lb (0.39 kg)Note: * the elevation adjustment lock provides 2X friction.143X360R, 3X360GMaintenance 3X360 CB Ceiling BracketCompatibility3X360 MLBClamp opening Max. 0.118 in (3 mm)Dimensions (H x W x D)Approx. 9.84 x 2.52 x 2.4 in (250 x 64 x 61 mm)Weight Approx. 0.84 lb(0.38 kg)MaintenanceTo maintain the Product, clean the case and optical glass and replace the batteries.The laser beam is dangerous to the eyes.Clean the ProductClean the case with a damp cloth and a weak soap solution.To clean the optical glass, use a pressurized can of air or a dry nitrogen-ion gun, if available, to blow off particulates from the optical surfaces.Replacing BatteryReplace the battery when the battery indicator LED is red.To install or replace RBP5 (Li-ion) using AA battery tray is not commended due to extremely short battery life (see Figure 2):1. Press down on the latch 1.2. While pressing down, pull back on battery pack and remove.3. Reinstall recharged battery pack.153X360R, 3X360GUsers ManualRBP5 Rechargeable BatteryFigure 3Housing Glass InsertIf the optical glass is damaged, replace the housing glass insert. See Table 6 for the part number to order for your Product. To replace the housing glass insert (see Figure 4):1. Remove the four housing glass insert screws2. Pull out the the tower insert and glass insert.3. Replace the insert and re-fasten screws.123Figure 4. Housing Glass Insert Replacement163X360R, 3X360GSpecifications SpecificationsSpecifications PLS 3X360R PLS 3X360GBattery (RBP5)Lithium-ion, 3.6 V, 5200 mAhBattery Life, Continuous Use (typical)3 beams: ≥ 9 hours1 beam: ≤ 30 hours3 beams: ≥ 5 hours1 beam: ≤ 17 hoursLine Fan AngleHorizontal360°Front Vertical360°Side Vertical360°Working RangeWithout line detector65 ft (20 m)115 ft (35 m) With line detector165 ft (50 m)210 ft (65 m) Accuracy± 5/64 in @ 33 ft (± 2 mm @ 10 m) Laser LevelingSystem Automatic PendulumRangeSelf-leveling: ≤ 4°Out of self-levelling: > 6°Leveling time≤ 3 sec TemperatureOperating14 °F to 122 °F (-10 °C to 50 °C)StorageWith Battery: -4 °F to 122 °F (-20 °C to 50 °C) Without Battery: -13 °F to 158 °F (-25 °C to 70 °C)Relative Humidity 0 % RH to 90 % RH (0 °C to 35 °C) 0 % RH to 75 % RH (35 °C to 40 °C) 0 % RH to 45 % RH (40 °C to 50 °C)IP rating IP 54Drop test 3.28 ft (1 m)Battery status indication 100%, 75%, 50%, 25% and low batterySize (H x W x L) w/ RBP5 5.12 in x 3.58 in x 5.25 in (13 cm x 9.09 cm x 13.33 cm) Weight (with battery) 1.76 lbs (0.8 kg)Li-ion battery safety IEC 62133Laser Safety Class 2 (IEC 60825-1) Light Source Semiconduction laser diodeMax Output Power< 1 mWWavelengthRed635 nm ± 10 nmGreen520 nm ± 10 nm Electromagnetic Compatibility (EMC)International IEC 61326-1Korea (KCC) Class A Equipment (Industrial Broadcasting & Communication Equipment) [1][1] This product meets requirements for industrial (Class A) electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and is not to be used in homes.USA (FCC) 47 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.17。

WR-10色差仪说明书目 录注意事项 (2)1 存放 (2)2 使用 (2)概述 (2)一、结构说明 (3)1.1 仪器外观 (3)1.2 电源 (4)1.2.1 电池 (4)1.2.2 电源适配器 (5)二、操作说明 (6)2.1 开机 (6)2.2 色差测量 (6)2.2.1 标样测量 (6)2.2.2 试样测量 (7)2.3 查看信息 (8)2.3.1 标样记录 (8)2.3.2 试样记录 (10)2.4 系统设置 (10)2.4.1 自动保存 (11)2.4.2 手动保存 (12)2.4.3 语言选择 (12)2.4.4 容差设置 (13)2.4.5 背光时间 (13)2.4.6 日期时间 (13)三、产品规格 (14)注意事项1 存放●长期不使用本仪器，应将仪器装入包装箱内存放；●存放温度为-10°C~50°C、相对湿度在85%以下的阴凉、干燥的环境中；2 使用●使用仪器时，环境温度为0°C~40°C、相对湿度在85%，无凝露；●避免在强磁场、剧烈震动、灰尘、烟雾的环境中使用本仪器，以防造成仪器数据异常和性能故障。

●避免液体、粉末、固体等异物进入仪器内部，以防造成测量数据异常。

概述本色差仪是依据国际照明委员会CIE的相关标准、国家标准研发生产的专业色差仪。

本色差仪采用全新进口关键元器件，经精心设计，具有精确稳定、操作简单、易学易懂、经济实惠等特点。

本色差仪适用于纺织、印染、服装、鞋业、皮革、化工、塑料、塑胶、颜料、油漆、油墨、印刷、五金、摄影、玩具等行业的颜色品质控制、色差控制、色差分析、来样检测、生产在线检测，也适用于注塑、油墨、油漆、喷涂等的辅助配色。

一、结构说明1.1 仪器外观图1 仪器外观图上移键-移动光标在页面中的位置；调整被激活项目的数值大小。

下移键-移动光标在页面中的位置；调整被激活项目的数值大小。

换页键-切换选项卡。

保存键-保存设置。

PRO 360 Owner's Manual2IntroductionThe Pro 360 Digital Protractor is a revolutionary measuring tool that provides an immediate, digital reading of all angles in a 360° circle. The machined aluminum frame is a rigid,light weight, ultra-precise platform that allows the state-of-the-art sensor and its microprocessor circuit to provide unsurpassed accuracy throughout the Protractor's 360° range.The Pro 360 uses an innovative liquid filled angle sensor. As the protractor is moved, the liquid seeks a new position, resulting in changes in the electrical properties of the sensor.A microprocessor analyzes the changes and calculates the numbers seen on the display.sensor3 Feature OverviewThe Pro 360 operates normally in a standard reference mode where level is displayed as 0.0°. However, a new reference point for 0.0° can easily be established by pushing the ALT ZERO button. You can also "freeze" any displayed angle on the LCD by pushing the HOLD button. The 360° range of the unit is organized into four 90° quadrants for display purposes. In each, the Pro 360 achieves an accuracy of + 0.1° at level and plumb with a maximum error of + 0.2° in between.And the Pro 360 does not need to be returned to the manufacturer or dealer for recalibration. By following the Superset® instructions in this booklet,you can test and recalibrate the Pro 360 in just a couple of minutes on site and without any special fixtures.ON/OFF buttonOperating Instructions - BatteryThe Pro 360 is powered by a 9-volt battery. A new alkaline battery will provide 500 hours of use. A 9-volt lithium battery can be used for even longer life.To extend battery life, the Pro 360 shuts off automatically when left undisturbed for five minutes (to reactivate, push the ON/OFF button). The Pro 360 also indicates when the battery is low. Change the battery when the display alternately flashes "LO bAt" with angle measure-ments. (NOTE: The Pro 360 does not display inaccurate angles due to a weak battery.)To install/replace the battery•Unscrew the battery compartment cover screw.•Remove the cover.•Install or replace the battery.•Replace the cover and tighten the screw.Do Not Overtighten45 Operating Instructions - Angle MeasuringFirst, you must make sure your unit is reading accurately by using the test on pages 8-9. If the unit fails this simple test, you must recalibrate it using Superset® (pages 10-12).To operate your Pro 360, simply push the ON/OFF button; it will begin displaying angle readings immediately. Set the Pro 360 on the surface to be measured and read the angle. (To get the most accurate reading, allow the unit to settle for 5 seconds before noting the angle.)alternate referenceplumb.Between 0° and 44.9level. Between 45°HOLD (temporarily "freezing" a reading on the display)If you need to take a measurement with the Pro 360 in an unreadable position, or if you need to temporarily lock in a reading while you record it, simply press the Hold button while measuring the angle. (Make sure the unit has been in position and still for 5 seconds.)(Superset®7 ALT ZERO(Setting an alternate reference point)ALT ZERO allows you to set any angle as a 0.0° reference point from which to take measurements. For example, you may want a surface that is actually 3° off horizontal displayed as 0° so you can measure all other angles from that benchmark.To set an alternate reference point, place the Pro 360 on the new surface and wait 5 seconds. Press the ALT ZERO button once. "Alt "will appear on the display, followedby "-0-". The Pro 360 will then display angles using the new reference. A flashing Iwill appear in the lower right hand corner of the display as long as the Pro 360 is in ALT ZERO mode.Press ALT ZERO again to return to standard reference mode. The Pro 360 also returns to standard reference when it is turned off or shuts off automatically.NOTE: You cannot activate the ALT ZERO button when the Pro 360 display is in HOLD.RecalibrationLike all measurement instruments the Pro 360 must periodically be monitored for accuracy. The Pro 360 should be tested daily with the simple procedure outlined below. If it is found to be out of calibration, it is easily recalibrated on site using Superset® - an eight-step procedure that realigns the unit through its entire 360° range and takes just a couple of minutes to perform. And Superset® doesn't require any special fixtures, tools, or expertise. Accuracy TestPerform this simple test each day before using the Pro 360. Also perform it anytime the Pro 360 has been dropped or is being used in an environment that varies more than 5°C (9° F) from the environment in which it was last calibrated. If your Pro 360 fails this test, you must recalibrate it using Superset® before using the unit further to measure angles.•Position the Pro 360 with the displayfacing you on a clean, flat horizontalsurface. It doesn't have to be exactlylevel. Wait 10 seconds so the unit iscompletely settled and note the angleon the display.89•Rotate the unit end-for-end so the display isfacing away from you. Be sure to set thePro 360 in exactly the same spot, and wait10 seconds before reading the angle that'sdisplayed.•Now roll the unit toward you so that thedisplay is facing you, but the lettering on theface of the unit is upside down. Wait 10seconds, and note the angle on the display.•Finally, rotate the unit end-for-end so thedisplay is facing away from you (thelettering should still be upside-down). Wait10 seconds and note the angle on thedisplay.•you must recalibrate (Superset®Superset®Superset® recalibrates the Pro 360 through its entire 360° range by electronically recording four horizontal and four vertical settings. It should be performed whenever the accuracy test shows a discrepancy of 0.1° or more.How to Perform Superset®Turn on the Pro 360 and place it on a flat surface. You can use any horizontal surface within 10° of level and any vertical surface within 10° of plumb to perform Superset®. You must use the same surfaces throughout the entire process.Note: Each time you reposition the Pro 360 during Superset®, wait a minimum of 10 seconds before pressing the HOLD button to advance to the next step.Starting Superset®• Press and hold the HOLD and ALT ZERO buttons simultaneously. Keep them depressed for approximately three seconds.• Release the buttons when the symbol "SUP" appears. A "0" within flashing brackets will then appear. These brackets are composed of four horizontal and four vertical segments. Note that as you proceed through the eight steps of Superset®a new segment will hold steady after you complete each step.1011 Superset® - Horizontal Settings[ 1]• Align with an edge or line - wait 10 seconds• Press HOLD button until [ 1] appears[ 2]• Rotate unit so it faces away from you, the letteringshould still be right-side up• Align with same edge or line - wait 10 seconds• Press HOLD button until [ 2] appears[ 3]• Roll unit so it faces you, the lettering should now beupside-down• Align with same edge or line - wait 10 seconds• Press HOLD button until [ 3] appears[ 4]• Rotate unit so it faces away from you, the letteringshould still be upside-down• Align with same edge or line - wait 10 seconds• Press HOLD button until [ 4] appearsYou have completed one half of Superset® (continued on next page)Superset® - Vertical Settings[ 5]• Place unit against vertical surface so it faces you, the lettering on the face ("Pro 360, etc.) should read from bottom to top• Align with an edge or line - wait 10 seconds• Press HOLD button until [ 5] appears[ 6]• Roll the unit so it faces away from you, the lettering should still read from bottom to top• Align with same edge or line - wait 10 seconds• Press HOLD button until [ 6] appears[ 7]• Rotate unit end-for-end so it faces you, the lettering should now read top to bottom• Align with same edge or line - wait 10 seconds• Press HOLD button until [ 7] appears[ 8]• Roll the unit so it faces away from you, the lettering should still read top to bottom• Align with same edge or line - wait 10 seconds• Press HOLD button. [ 8] will very briefly appear, followed immediately byregular angle measuring.Pro36Pro360 Pro 360 Pro 3601213Your Pro 360 has been Superset® back to manufacturer's spec's.Canceling Superset®You may cancel Superset® at any time during the process by turning the unit off.MaintenanceThe Pro 360 is designed to stand up to the rigors of industrial use. The following tips will ensure a long service life:• Use the "end-for-end" accuracy test daily to make sure the unit is in calibration. If it is not, recalibrate it immediately with Superset®.• Clean the Pro 360 with mild liquid soap and a damp cloth. Never immerse in water.• Do not use solvents directly on any of the Pro 360 plastic surfaces.• Store the Pro 360 away from extreme temperature: Never below -20° C (-4° F) or above 65° C (149° F).Pro 360 - Specifications Range............360° (90° x 4) Resolution.....0.1°Accuracy.......+0.1° level +10°; plumb +10°+0.2° maximum error TemperatureOperating....-5° C to 50° C (23° F to 122° F) Storage........-20° C to 65° C (-4° F to 149° F)Weight...................289 g. (10.2 oz.) Repeatability........+0.1°Cross Axis Error..Minimal Power....................9 V. Alkaline Battery Battery Life..........500 hours typical Warranty..............1 year, limited14ATTENTIONYour new digital protractor must be calibrated before use to ensure accurate readings. See your owner’s manual for Superset® calibration instructions.WARNINGDO NOT PLACE BATTERY IN BACKW ARDSOne-Year Limited WarrantyIf, within one year from the date of original purchase, the Pro 360 Digital Protractor fails to function because of defects in materials or workmanship, the manufacturer will, at its option, either repair or replace such components provided the original purchaser:1.Contacts the dealer from whom the unit was purchased for instructions;2.Follow the dealer's instructions for return of the unit;3.Submit original date and proof of purchase;4.Includes a brief explanation describing why the Pro 360 Digital Protractor is inoperable, or how it was damaged. This warranty does not cover damage resulting from accident, misuse or abuse, water, tampering, servicing performed or attempted by unauthorized agencies, units that have been modified in any fashion, or units that have not been recalibrated and maintained in accordance with the instructions in this manual.If the components do not perform as warranted herein, the original purchaser's sole remedy will be the repair or replacement of the components as provided above. In no event will the manufacturer be liable for damages, lost revenue, lost wages, lost savings, or any other incidental or consequential damages, domestic or international, rising from the purchase and use or inability to use the components even if the manufacturer has been advised of the possibility of such damages.Except as provided herein, the manufacturer makes no warranties, express or implied, including without limitation, the implied warranties of merchantability and fitness for a particular purpose, with respect to the components. All warranties for the components, express or implied, are limited to the warranty period set forth above. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.This warranty gives you specific legal rights. You may also have other rights, as indicated above, which vary from state to state.85310613。

DataMan®360系列快速参考指南2019/03/22预防措施激光，不要直视激光束：2级激光产品。

不遵守这些指示可能导致严l注意—使用任何非此处指定的控件、调节装置或者操作程序，均可能导致有害的辐射泄漏。

l不要尝试保养或修理本产品—应将它退回Cognex进行保养。

l不允许任何非Cognex公司的人员保养、修理或调节本产品。

l除本文档中所述情况外，不要尝试打开或改装本设备。

l不要将激光直接照射或反射到人或反射体。

l如果设备损坏，盖子或密封件丢失或受损时，不要操作本设备。

l仅当所有接口都连上电缆或用密封盖屏蔽时，才能确保IP保护。

本激光产品在整个操作过程中按2类产品设计。

波长650纳米激光功率等级<1mW光束直径<3毫米（孔径）发散度< 1.5毫拉德产品概览1激光瞄准器2照明LED簇3外部照明安装点4安装孔（M3X5毫米）5指示灯光圈6触发按钮7电源8训练状态9读取/未读取指示灯10网络11错误12峰值计13调谐按钮14以太网15SD卡槽16外部照明控制17电源、I/O和RS232DataMan 360配件镜头选件和镜头盖带锁定的10.3毫米M12镜头(DM300-LENS-10)和带锁定的10.3毫米IRM12镜头(DM300-LENS-10-IR)液体镜头模块和带扳手的预对焦10.3毫米或10.3毫米IR M12镜头(DM300-LENS-10LL)、(DM300-LENS-10LL-IR)19毫米液体镜头模块(DM300-LENS-19LL)带锁定的16毫米M12镜头(DM300-LENS-16)24毫米F6液体镜头模块(DM360-LENS-24LL)带镜头垫片和六角扳手的25毫米M12镜头(DM300-LENS-25)（也需要扩展套件）扩展套件(DM300-EXT)DM500C 型镜头盖(DM500-CMTLC-000)（与HPIA 配套使用）DM500镜头盖扩展器(DM500-LNSEXT-000)蓝色(CKR-BP470)、红色(CKR-BP635)、绿色(CKR-BP525)、橙色(CKR-BP590)带通滤波器透明镜头盖(DM300-CLCOV)带白色LED 照明的透明镜头盖(DM300-CLCOV-WHI)通过IEC 62471风险组豁免级标准带红色LED 照明(DM300-DLCOV-RE)、带蓝色LED 照明(DM300-DLCOV-BL)、带红外线LED 照明(DM300-DLCOV-IR)的散射镜头盖，带红色LED 照明(DM300-PLCOV-RE)的偏振镜头盖通过IEC 62471风险组豁免级标准外部灯（红色LED）和大功率照明环形灯(CLRR-R7030G1CLR)背照灯(CLRB-F100100G1)同轴(DOAL)灯(CLRO-K5050G1)聚光灯(CLRS-P14G1)暗场灯(CLRD-D120G1)其他*xx可能是美国、欧洲、英国或日本。

电子尺使用说明（一）引言概述：电子尺是一种用于测量长度和距离的便携式电子设备。

它采用数字显示和精确测量功能，可以广泛应用于建筑、工程、设计和家庭使用等领域。

本文将详细介绍如何正确地使用电子尺。

正文内容：一、电子尺的外观和功能：1. 电子尺的外观特点2. 电子尺的主要功能和特性3. 电子尺的标尺类型和测量单位4. 电子尺的操作按钮和显示屏5. 电子尺的电源和节能功能二、使用电子尺测量长度和距离：1. 打开电子尺和调整测量模式2. 选择正确的测量单位3. 将电子尺放置在待测量的物体上4. 观察和记录测量结果5. 清零电子尺并保存测量结果三、使用电子尺进行辅助测量：1. 使用电子尺的角度测量功能2. 使用电子尺的深度测量功能3. 使用电子尺的面积和体积测量功能4. 使用电子尺的前后测量功能5. 使用电子尺的连续测量功能四、电子尺的注意事项和维护方法：1. 避免电子尺与其它物体发生碰撞2. 防止电子尺受潮和受高温环境影响3. 定期清洁电子尺的外壳和显示屏4. 使用电子尺时要注意安全事项5. 如果电子尺出现故障，应咨询专业人士进行修复五、电子尺的优点和适用范围：1. 电子尺的精度和准确性优势2. 电子尺的便携和易于携带3. 电子尺在建筑和工程领域的应用4. 电子尺在设计和绘图领域的应用5. 电子尺在家庭和日常生活中的应用总结：电子尺是一种方便实用的长度和距离测量工具。

通过正确使用和维护，可以充分发挥其精准测量的功能。

希望本文所提供的电子尺使用说明能帮助用户更好地应用于各种领域，并取得满意的测量结果。