广州南方卫星导航仪器有限公司
GIS部说明文档
S750 G2 设置网络连接
开始-设置-连接-添加新调制解调器连接-选择电话线路（GPRS），下一步-接入点名称输入：CMNET，下一步-我的连接：用户名、密码、域空出不输入。
完成设置。
备注：每一次插SIM以后需要重新启动一下系统，这样才能读到新插上去的SIM卡。
具体操作：1、点击关机复位键。
2、长按power键直至指示灯绿灯亮，重新启动系统。
连接接入第三方软件（连接CORS）
外部源的设置，一般为工作中的主要方式，界面与南方以往的调试软件界面相似，操作略有不同。
参数设置：
IP地址：基准站服务器的地址
端口：基准站服务器发送数据的端口
接入点：获得后才能选择，为对应的基准站编号
及差分格式
注意必须为带_RTD的差分源
用户及密码：验证项目，由基准站服务器管理人提供或者是任意的。
点击停止可以对IP地址、端口、用户名、密码进
行编辑。
再点击开始获取源列表，选择对应的接入点
以后退出即设置好了CORS连接。
最后提示登录成功，当达到差分3D、传输数据以
后说明连接CORS已经正常了。
备注重要: 1、连接CORS之前确保第一步的网络设置成功，可以正常登录网页。
2、电话功能保持打开状态。
广州南方卫星导航GIS部
2010年12月。
S750G2操作流程1，开关机：开机，长按PWR键直到屏幕亮时松开就能开机了。
关机，由于这是Windows操作系统，关机时只能通过系统关机，点击左下角“开始菜单”→“关闭”→“关闭”（图一）完成关机。
（注：短按PWR键虽然屏幕也是熄灭状态，这是待机状态，电池会自动放电。
）（图一）2，打开软件，双击桌面上的“GIS数据采集”即可打开我们所需的软件（图二）。
进入主界面试图（图三），快捷工具栏图标含义（图四）。
（图二）（图四）（图三）3，新建工程:点击“管理”→“工程”→“新建工程”（图五），“工程名称”后面输入工程的名称，点击“下一步”（图六），（图五）（图六）点击“编辑”对坐标系统进行设置（图七），点击“椭球”选项卡设置我们需要的坐标系（图八）。
（图七）（图八）点击“投影”选项卡输入我们当地的中央子午线（图九）。
如果我们还有“七参”“四参”“高程”“垂直”或“校正”参数的话，可以点击对应的选项卡输入。
最后在“名称”后面输入坐标系统的名称（建议最好和工程名称相同），都输入完成后点击“确定”（图十）回到坐标系统界面。
（图九）（图十）选择我们所编辑的坐标系统（图十一）点击“下一步”，进入记录条件界面，此界面下可以对“状态限制”“PDOP限制”“HRMS 限制”“VRMS限制”进行设置，其中“状态限制”必须选择“差分3D”（图十二），其他限制值越小越好（注：其他的限制条件一般情况下保持默认值就行）。
（图十一）（图十二）都设置好后点击“下一步”进行新建文件，在“文件名称”后面输入文件名称，一般用选用“手动命名”（图十三），（注：文件名称一般用当天的日期为好），输入完文件名称后点击“完成”完成工程的新建。
（图十三）4，GPS设置：点击“管理”→“GPS”→“基本设置”（图十四），在差分模式后面选择“SBAS”（图十五），→点击“SBAS设置”，在选择模式后面选择“定制的SBAS卫星”→点击“确定”→“确定”（图十四）（图十五）（图十六）再点击“管理”→“GPS”→“信息查看”（图十七），点击“测试”出现GPS端口调试界面，看接受后面是否有数据返回，如果有数据返回点击右上角的“X”号关闭就行，如果没有数据返回，点击左下角“关闭”再点击“打开”就会有数据返回的(图十八)。
OPERATORʼS MANUAL Red-D-Arc Spec-Built Welding Equipment This RED-D-ARC welder is built to RED-D-ARC Extreme Duty design specifications by Lincoln Electric.Safety Depends on YouThis welder is designed and built with safety in mind.However, your overall safety can be increased by proper installation ... and thoughtful operation on your part.DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT.And, most importantly, think before you act and be careful.1-800-245-3660AUG 06Jan, 07Mar. ʻ93vvThank Youfor selecting a QUALITY product. We want you to take pride in operating this product ••• as much pride as we have in bringing this product to you!K857 remote to the 14-pin wire feeder connector on the front of the EX350i.PARALLEL OPERATIONThe EX350i are operable in parallel in CC mode. For best results, the currents of each machine should be reasonably well shared. As an example, with two machines set up in parallel for a 400 amp procedure, each machine should be set to deliver approximately 200 amps, not 300 amps from one and 100 amps from the other. This will minimize nuisance shutdown conditions. In general, more than two machines in parallel will not be effective due to the voltage require-ments of procedures in that power range.To set machine outputs, start with output control pots and arc control pots in identical positions. Use the output control pots to balance the currents and main-tain the desired voltage or current. The arc control pots should be kept identical on the two machines.5.THERMAL• This status light indicates when the power source has been driven into thermal overload. If the output terminals were "ON", the "ON" light will blink indicating that the out-put will be turned back on once the unit cools down to an acceptable temperature level. If the unit was operating in the "REMOTE" mode, the trigger will need to be opened before or after the thermal has cleared and closed after the machine has cooled down to an acceptable tempera-ture to establish output.6.CONTROL-REMOTE / LOCAL• Two status lights indicate the location of output control as pre-determined by the power sources auto-configure sys-tem.• The LOCAL display will be lit when control is at the power source.• The REMOTE display will be lit when a remote pot/control is detected.These O utput Control configurations can be overridden (switched) with the CO NTRO L push button. When changed, the unit will power up in the configuration it was in when it was last powered down.Hidden Middle Control Panel – Process Set Up Panel7. WELD MODE SELECT -The Mode Control button selects from the following welding modes. CC-STICK SOFT:The Stick Soft process features continuous control ranging from 5 to 425 amps. This mode was intended for most SMAW applications, and Arc Gouging.• Arc Gouging: Setting the output of the Stick Soft mode to 425 amps will enable the arc-gouging mode. The actual output current will depend on the size of carbon used. The recommended maximum size carbon is 5/16".• The Hot Start control regulates the starting current at arc initiation. Hot Start can be adjusted from min-imum (0), with no additional current added at arc start, to maximum (10), with double the preset cur-rent or 425 amps (max of machine) added for the first second after arc initiation.• The Arc Control regulates the Arc Force to adjust the short circuit current. The minimum setting (-10) will produce a "soft" arc and will produce minimal spatter. The maximum setting (+10) will produce a "crisp" arc and will minimize electrode sticking.CC-STICK CRISP: The Stick Crisp mode features continuous control from 5 to 425 amps. This mode was intended primarily for pipe welding applications.• The Hot Start control regulates the starting current at arc initiation. Hot Start can adjust starting current up or down by 25% of the preset value. The recom-mended setting for Hot Start is 5 where the initial current is equal to the preset current.• The Arc Control regulates the Arc Force to adjust the short circuit current. The minimum setting (-10) will produce a "soft" arc and will produce minimal spatter. The maximum setting (+10) will produce a "crisp" arc and will minimize electrode sticking.WELD MODE DETAILS:AUXILIARY POWER• 115VAC, 42VAC and 24VAC power is available from the two 14-pin amphenols on the rear of the unit. These supplies are intended to supply power for auxiliary equipment like wire feeders and the TIG Module.• 115VAC supply is rated at 2 amps and is protected by a 2.5 amp breaker located by the amphenol.• 42 VAC supply is rated at 5.5 amps and is protected by a 10 amp breaker located by the amphenol.• 24 VAC supply is rated at 5.5 amps and is protected by a 10 amp breaker located by the amphenol. LIMITATIONS• The EX350i is not recommended for processes other than those listed.• The EX350i can only be used with the recommend-ed equipment and options.RECOMMENDED PROCESSESProperly equipped, the EX350i supports GMAW, FCAW, SMAW, GMAW-P, GTAW and CAC-A processes for a variety of materials, including mild steel, stainless steel, cored wires, and aluminum.OPTIONS / ACCESSORIES• K2176-1Twist-Mate to Lug Adapter• K1764-1Inverter and Feeder Cart• K1557Swivel Kit• K1702-1Dual Cylinder Kit (For K1764-1)• K1838-2Valet Style UndercarriageWelding Cable Connectors:• K852-70 1/0-2/0 cable• K852-95 2/0-3/0 cable•K857Remote Output Control 25ft.• K814 Arc Start Switch• K963-[ ]Hand Operated Amptrol• K870Foot Operated AmptrolNote: All of the above remote controls have a 6-pin MS-style connector, a K864 or K876 adapter is need-ed to connect them to the 14 pin wire feeder MS-style connector. (See Diagram in Section F-1)K930-2 TIG ModuleK428 LN-25 Wire Feeder with meters*K449LN-25 Wire Feeder *K617-1 LN-742 Wire Feeder W/2 Roll Drive K618-1LN-742 Wire Feeder W/4 Roll Drive K440-2LN-7 GMA Wire FeederK567-2LN-7 GMA Wire Feeder W/4 Roll Drive K1559-1LN-10 Bench Model (CV)K1564-1LN-10 Generic 16ft. Boom Package K1499-1DH-10 Bench ModelK1521-1DH-10 Generic 16ft. Boom Package K1853-1Cobramatic*Not recommended for pulse weldingFIELD INSTALLED OPTION• K1762-2 TIG Gas Control Kit• K1763-1 Advanced Process Panel QUICK DISCONNECT PLUGSA quick disconnect system is used for the welding cable connections. The K852-70 is designed to accept a welding cable size of 1/0 to 2/0.1.Remove 25mm (1 in.) of welding cable insulation.2.Slide rubber boot onto cable end. The boot endmay be trimmed to match the cable diameter.Soap or other lubricant will help to slide the boot over the cable.3.Slide the copper tube into the brass plug.4.Insert cable into copper tube.5.Tighten set screw to collapse copper tube. Screwmust apply pressure against welding cable. Thetop of the set screw will be well below the surface of the brass plug after tightening.6.Slide rubber boot over brass plug. The rubberboot must be positioned to completely cover allelectrical surfaces after the plug is locked into the receptacle.25 mm1 in.WELDING CABLEBOOTTRIMET CREWBRA L GCO ER T BEThis Troubleshooting Guide is provided to help you locate and repair possible machine malfunctions.Simply follow the three-step procedure listed below.Step 1.LOCATE PROBLEM (SYMPTOM).Look under the column labeled “PRO BLEM (SYMP-TO MS)”. This column describes possible symptoms that the machine may exhibit. Find the listing that best describes the symptom that the machine is exhibiting.Step 2.POSSIBLE CAUSE.The second column labeled “POSSIBLE CAUSE” lists the obvious external possibilities that may contribute to the machine symptom.Step 3.RECOMMENDED COURSE OF ACTIONThis column provides a course of action for the Possible Cause, generally it states to contact your local Authorized Field Service Facility.If you do not understand or are unable to perform the Recommended Course of Action safely, contact your local Authorized Field Service Facility.HOW TO USE TROUBLESHOOTING GUIDEService and Repair should only be performed by Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual.__________________________________________________________________________JapaneseChineseKoreanArabicREAD AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.JapaneseChineseKoreanArabicLEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.。
