BLACK-310硫酸纸增黑机 - 广电电器网-家电维修、说明书

CXBG-1-PS-SZN3103-W说明书（适配海康）(加防弦隔栅）(标准)版权声明本手册中所提及的其它软硬件产品的商标与名称，都属于相应公司所有。

本手册的版权属于本公司所有。

未得到本公司的正式许可，任何组织或个人不得以任何手段和形式对本手册内容进行复制或传播。

本手册的内容若有任何修改，恕不另行通知。

产品概述CXBG-1-PS-SZN3103-W系列数字LED闪光灯（工业级）是专门针对治安卡口、超速抓拍、闯红灯等，室外电子警察的工作环境和功能要求而研制开发的大功率高性能数字脉冲闪光灯。

该产品采用我公司最新研发的专业闪光控制电路，具有回电快、寿命长、准确的控制闪光时间、闪光瞬间内保持以大功率方波形式输出有效地供给相机曝光周期内所需的光能量等特点。

能够满足在各种光线条件下，辅助摄像系统实现对车辆和驾驶员清晰拍照的要求。

技术指标型号：CXBG-1-PS-SZN3103-WLED灯珠: 科锐5W高亮LED 16PCS色温：6000K-6500K（色温可定制）光源波长：400-780nm中心强度：150lx@20m光照角度: 支持10度、30度、45度（可选）标准配置（10度）启闭功能：支持摄像机控制防误触发：错误脉冲保护功能供电电源：AC165-220V功耗：平均≦35W，峰值180W补光范围：距离15-28M，宽度5-10M同步接口：频闪触发输入触发方式：开关量/高电平防雷：共模4KV、差模2KV外壳材质：金属铝+钢化玻璃支架：多向转动方式（节省安装成本）散热方式：直导式散热防护级别：IP66工作环境温度：-40～+60℃存储温度：-40～+85℃重 量： 净重2.4kg外形尺寸：122x125x134 （mm ）产品执行标准：GA/T1202-2014本公司已通过德国TUV ISO9001-2008质量管理体系认证硬件接口CXBG-1-PS-SZN3103-W 型闪光灯的频闪接口。

接线定义 管脚 引出线颜色 信号 说明 1 红色频闪触发正极 2 黑色 频闪触发负极闪光灯与摄像机接法结构尺寸摄像机 F+F- 触发正极 触发负极 LED 灯 a ：122mm b ：125mmc ：134mmd ：180mme ：7mmf ：70mm售后服务产品除人为原因和不可抗力损坏外，整机免费保修36个月，终生成本维修。

墨机三灯闪烁处理方法在控制面板上一起按住墨水键和进纸键然后开机，开机后3秒钟时，就立刻把进纸键的手松开，这时墨水键的手还按着大约10秒后就出现三灯再闪，这时可以把手放开，这样就能把ROM清好，主板就OK了。

这一操作的作用是将废墨计数器清零。

此外，还可以通过调整程序达到这一目的。

如果两年前遇到这种三灯闪故障全部都换主板，到了后来就进一步修主板，现在只是在控制面板按几下就OK，这说明修打印机要有经验，耐心才能把故障排除。

打印头电缆断线故障分析打印头电缆一般都采用塑料柔性带状电缆。

这种电缆在使用过程中容易产生折痕，一种是插在打印头插座一端的电缆，随着打印头的插拔次数增多，在折痕处就会发生断裂(修理时需将打印头拆下)；另一种是随着打印时间的增加，打印电缆的中间部分很容易在字车移动过程中被磨损或产生折痕。

若将电缆上的绝缘层磨掉，会使打印针驱动信号与打印机机架短路，导致打印机主控电路故障；若打印电缆折痕处断裂则会使打印针驱动信号开路，引起对应的打印针不出针打印，致使打印字符／汉字缺点少划。

电缆的这两种故障可以用万用表检查。

方法是将万用表的两根表笔分别搭在电缆两端的对应线上，量其电阻是否为零，必要时还要在折痕处作弯曲试验，观察万用表上的阻值有无变化。

在确诊有断线后，用相同机型的打印头电缆更换即可。

切记电缆的断裂处不能用焊接的方法处理，因为这样会在使用过程中出现信号短路法处理，严重时将导致信号对地短路，引起打印机的主控电路产生故障。

在打印头电缆出现折痕，但末折断时，可采取预防措施，避免信号线折断。

其方法是：先截一段长约1．5cm的粘胶带，随后将一条长约o，5cm、宽度与粘胶带宽度相同的薄纸片贴到胶带的中部，以避免胶带中部与电缆粘在一起。

然后使电缆在折痕处微微向外弯曲，让纸片对正折痕，将胶带贴到电缆上。

这样，胶带片产生的拉力就会始终迫使电缆在折痕处微微向外弯曲，从而使电缆在折痕处产生一个向外的合适张力，这样可以可*地避免打印头在打印过程中向右运动致使电缆在折痕处产生折卷，防止打印头电缆中信号线的折断。

第一章修理操作前的各项准备工作1.1修理操作的先决条件1.2使用工具第二章照明系统修理程序2.1超高压汞灯电源异常2.2照明均匀性异常和曝光功率降低第三章硅片传输系统的修理程序3.1硅片传输系统的真空异常3.2 OF检测失灵3. 3预对准工作异常3. 4上下片臂定位不良（以上全部维修程序请参考微高公司提供的维修手册）第一章修理操作前的各项准备工作1.1修理操作的先决条件能进行操作和精读检验能够使用示波器照度计等测量仪器注意事件：抽出电路板时，请先关断电源拿起电路板时请勿用手指接触链接点打开或关断控制单元电源时，先将控制计算机正确关闭对光学系统进行清洁处理时，请务必戴上洁净手套1.2使用工具使用工具一览表消耗品一览表使用各种工具时，请注意以下事项：要参照使用说明书对示波器及时进行探测头校准，保持其精读，尤其在更换探头时，请务必加以校准。

松开或上紧螺栓螺母之类机件时，请使用尺寸合适的工具，且施力恰当，以免损坏机器。

调整电位器，请注意方向，本文中标有CW时，按顺时针方向旋转, 标CWW,按反时针方向旋转。

第二章照明系统修理程序凡涉及机械电气光学压力流量位置等调整时，请专业人士协助实施。

否则后果自负。

2.1超高压汞灯电源异常程序1：超高压汞灯电源操作面板的检验对外围室(净化室)前而的操作而板进行如下的检测：电源开关是否打开？触发开关是否打开？报警灯是否亮？程序2：超高压汞灯控制箱的检验。

对外室上而的超高压汞灯控制箱进行如下检验：打开电源开关电源指示灯是否发亮风扇是否转动程序3： AC200V系统的检验打开外围室左侧后部的电控箱门，检验超高压汞灯电源的短路器是否处于通路状态。

程序4：恒温器的更换方法工具：六角起子套件十字起子套件关闭操作而板上的电源开关，然后再关闭汞灯控制装置内的电源开关。

约等30分钟，灯罩内达到足够冷冻状态。

松开右侧1个十字螺钉灯罩左侧两个十字螺钉，取下灯罩盖。

取下灯罩的盖子，用六角形起子将位于黑色板子上部的恒温器卸下。

前言感谢您使用本公司的产品。

在安装和使用本打印机之前，请您务必仔细阅读本手册及随机配送的所有资料，特别是安全注意事项部分，并按照本手册的说明及要求安装、使用和维护保养本产品，以避免因不正确的安装、使用和维护保养可能导致的产品损坏或其他问题。

[限制说明]我们已经对本手册进行了严格仔细的校勘和核对，但不能保证本手册完全没有任何错误和疏漏。

本手册中的图片仅供参考，如果有个别图片与产品的实际显示不符，请以实际产品为准。

产品的实际配置及规格，应以适用于本产品的配置和规格描述文件（如装箱清单等）为准。

本手册中提及的某些部件、组件、功能和特征仅用于说明目的，可能仅适用于某些特定规格和型号的产品，而非对本产品实际配置和规格的描述，请您在阅读本手册时认明。

我们保留随时对本手册描述的产品和/或软件程序进行改进和/或修改的权利，如有此类改进和/或修改，相应的产品手册也会随之调整，恕不另行通知。

请您务必妥善保管和随时备份您的数据资料。

对于因本产品使用、不能使用、维修或者其他情况引起的数据资料丢失和损坏，以及由此造成的其他损失，在法律允许的最大范围内，我们不承担责任。

[权利声明]本手册内容受著作权法律法规保护，未经我们事先书面授权，任何人均不得以任何方式复制、抄录本手册，或将本手册的全部或任何部分以任何形式在任何有线或无线网络中进行传输，或将其编译、翻译成任何其他格式、文字或代码。

本手册中描述的软件，其使用和复制应根据本公司与您的许可协议进行。

本手册中所涉及的商标属其合法持有者所有。

如果本手册中提及、使用了任何第三方的商标、商号，仅为说明或演示目的，并不表明本产品或服务与这些第三方有任何关系。

安全请在使用本产品前仔细阅读本手册，不要执行本手册中没有明确说明的操作。

未经授权的操作会导致错误或意外。

制造商对因错误操作而导致的任何问题均不负责。

为了防止人员受伤、触电、或引起火灾、机器故障等，请您务必遵守以下注意事项：z在安装使用本机之前，请仔细阅读本手册，并请妥善保存本手册，以便了解正确用法和各项功能，以及使用过程中出现疑问时查询。

警告、注意和提示通则1 这本手册上的警告和注意对于全体人员与设备的安全是非常重要的.任何想操作、维护、修理设备的人员,所有的警告和注意事项都应该事先读懂。

2 警告和注意事项出现在相关操作过程的章节中,它们是首要信息的总结。

警告3 在操作或维护过程，练习或说明中,警告是必须完全遵守的，否则会造成人员伤亡或设备的严重损害.4 警告是以大与黑体、较大的打印（14点）出现，就象通路上出现的“Stop”。

注意事项5 在操作、练习或维护过程中，说明中的注意事项亦是必须完全遵守的，否则会造成设备的损害。

6 注意事项以小写黑体，较大的打印（14点）出现，就象通路上出现的“注意":提示7 提示指出在操作或维护过程中，练习或说明中不具备危害的特性。

8 提示以小写较大的喷印(14点)出现，就象交通路上“提示"：补充警告：9 下面出现的警告在这本手册中是通用的。

要操作和维护设备的所有人必须读,必须彻底理解。

（1)、人员伤害。

在处理墨水和清洗溶剂时必须穿戴有遮边的保护眼镜及保护手套.（2）、人员伤害。

避免长时间呼吸到墨水和清洗溶剂。

立即清洗干净所溅出的墨水和清洗溶剂。

（3）、人员伤害。

在安装和移动墨水盒时要断开空气的供给，墨水系统解压，不得将有压力的墨水瓶移出保护罩，不得超出系统要求的最大压力。

(4）、人员伤害。

在任何时候遵守安装和操作指示。

但仅有受过训练的人可以维护及维修设备。

(5）、火警。

水性墨水在干燥后有可燃性余渣。

妥善处理墨水,清洗溶剂，及擦过它们的碎布等。

不要将墨水和溶剂倒入通常的排水系统。

要按你们地区或国家的要求来处理它们。

（6）、电气警告.要工作的电气设备，察看是否符合所有的电气安全规定和条例。

(7)、重要警告。

当要执行维护和修理工作时，关闭所有动力源，除非必须开著电源以进行调整。

设备损害。

断开或连接任一电缆到喷印机时，电源必须关闭.缩写10 本手册使用以下缩写：A 安培AC 交流电℃摄氏温度CPU 中央处理器EPROM 可擦只读存贮器Kg 公斤mm 毫米PSI 磅/平方英寸RTC 实时钟信息通则11 这本手册描述的是WILLETT3150喷墨喷印机图形和表格12 在这本手册里图形和表格的号码是按照它们被使用的章节来命名的（如：图1。

目录规定 (V)安全信息 (Ⅵ)第1章 规格...............................................................................................................1-1 1. 规格表............................................................................................................................1-11.1 概述........................................................................................................................................1-11.2 网络连通性.............................................................................................................................1-31.3 维修信息.................................................................................................................................1-31.4 耗材........................................................................................................................................1-31.5 纸张........................................................................................................................................1-41.5.1 纸张操作.........................................................................................................................1-41.5.2 介质规格.........................................................................................................................1-41.6 可打印区域.............................................................................................................................1-5第2章 故障排除......................................................................................................2-1 1. 介绍...............................................................................................................................2-11.1 预防措施.................................................................................................................................2-11.2 初期检查.................................................................................................................................2-22. 概述...............................................................................................................................2-42.1 截面图....................................................................................................................................2-42.2 纸张送入.................................................................................................................................2-52.3 各个部件的作用......................................................................................................................2-62.4 电子总结构图..........................................................................................................................2-72.5 部件........................................................................................................................................2-83. 指示灯的出错显示及各类故障........................................................................................2-93.1 正常操作时的指示灯显示........................................................................................................2-93.2 需要维修时的指示灯显示......................................................................................................2-123.3 监控屏幕上的出错信息.........................................................................................................2-173.4 需要维修时的错误提示.........................................................................................................2-183.5 图像缺陷的示例....................................................................................................................2-204. 错误的症状/原因与措施..............................................................................................2-214.1 纸张送入故障........................................................................................................................2-214.1.1 纸盒的撮纸功能失效.....................................................................................................2-214.1.2 无纸张送入...................................................................................................................2-214.1.3 手动进纸槽中无纸张.....................................................................................................2-224.1.4 双页送入.......................................................................................................................2-224.1.5 卡纸..............................................................................................................................2-224.1.6 纸面上的污点................................................................................................................2-244.1.7 纸张歪斜送入................................................................................................................2-244.1.8 纸张皱褶.......................................................................................................................2-244.1.10 双面打印时只能打印单面............................................................................................2-25 4.1.11 无法进行双面打印......................................................................................................2-26 4.1.12 纸张尺寸出错..............................................................................................................2-26 4.1.13 双面打印所用纸张尺寸出错........................................................................................2-26 4.2 图像缺陷的故障排除.............................................................................................................2-27 4.2.1 太浅..............................................................................................................................2-27 4.2.2 定位不良.......................................................................................................................2-29 4.2.3 太深..............................................................................................................................2-29 4.2.4 定影不良.......................................................................................................................2-29 4.2.5 完全空白.......................................................................................................................2-30 4.2.6 图像失真.......................................................................................................................2-30 4.2.7 全黑..............................................................................................................................2-31 4.2.8 纸张背面脏...................................................................................................................2-31 4.2.9 垂直条纹.......................................................................................................................2-32 4.2.10 浅色背景上的黑色垂直条纹........................................................................................2-32 4.2.11 黑色水平条纹..............................................................................................................2-33 4.2.12 白色垂直条纹..............................................................................................................2-34 4.2.13 白色水平条纹..............................................................................................................2-34 4.2.14 打印模糊.....................................................................................................................2-34 4.2.15 白色斑点.....................................................................................................................2-35 4.2.16 黑色斑点.....................................................................................................................2-35 4.2.17 黑色条带.....................................................................................................................2-35 4.2.18 向下渐模糊纯色块......................................................................................................2-36 4.2.19 水平线条.....................................................................................................................2-36 4.2.20 重影............................................................................................................................2-36 4.2.21 图像模糊.....................................................................................................................2-37 4.3 软件设置问题........................................................................................................................2-38 4.3.1 无法打印数据................................................................................................................2-38............................................................................2-38 4.4 网络问题(仅限于离 )4.4.1 无法通过网络连接进行打印..........................................................................................2-38 4.5 墨粉和硒鼓问题....................................................................................................................2-39 4.5.1 尽管更换了墨粉盒，但仍显示" Replalce Toner "..........................................................2-39 4.5.2 无法检测出墨粉盒........................................................................................................2-39 4.5.3 墨粉不足.......................................................................................................................2-39 4.5.4 更换墨粉盒...................................................................................................................2-39 4.5.5 墨粉盒寿命到期............................................................................................................2-40 4.5.6 墨粉盒未装入................................................................................................................2-40 4.5.7 硒鼓寿命即将到期........................................................................................................2-40 4.5.8 硒鼓出错.......................................................................................................................2-40 4.5.9 硒鼓寿命到期................................................................................................................2-40 4.6 定影单元问题........................................................................................................................2-414.7.1 激光单元故障................................................................................................................2-414.8 电路板问题...........................................................................................................................2-424.8.1 主板故障.......................................................................................................................2-424.8.2 内存已满.......................................................................................................................2-424.8.3 打印超限.......................................................................................................................2-424.8.4 高压电源电路板组件故障..............................................................................................2-424.8.5 低压电源电路板组件故障..............................................................................................2-434.9 其他问题...............................................................................................................................2-434.9.1 设备电源无法打开或不出现指示灯显示........................................................................2-434.9.2 风扇不运转...................................................................................................................2-434.9.3 主马达故障..................................................................................................................2-444.9.4 前盖未关闭..................................................................................................................2-444.9.5 后盖未关闭..................................................................................................................2-44第3章 拆卸和重新安装...........................................................................................3-11. 安全注意事项................................................................................................................3-12. 包装...............................................................................................................................3-23. 螺丝目录........................................................................................................................3-34. 紧固扭矩列表.................................................................................................................3-45. 润滑...............................................................................................................................3-56. 齿轮概述........................................................................................................................3-67. 插线路径........................................................................................................................3-98. 拆卸流程图..................................................................................................................3-179. 拆卸步骤......................................................................................................................3-189.1 纸盒......................................................................................................................................3-199.2 后盖......................................................................................................................................3-229.3 外斜槽组件...........................................................................................................................3-249.4 定影单元盖...........................................................................................................................3-259.5 内斜槽组件、左/右出纸挤压辊组件....................................................................................3-269.6 前盖组件、挡板1.................................................................................................................3-289.7 左侧盖..................................................................................................................................3-299.8 右侧盖..................................................................................................................................3-309.9 顶盖组件...............................................................................................................................3-319.10 定影单元.............................................................................................................................3-359.11 低压电源电路板组件...........................................................................................................3-389.12 风扇马达60组件................................................................................................................3-419.13 高压电源电路板组件...........................................................................................................3-429.14 面板电路板组件..................................................................................................................3-439.15 过滤器................................................................................................................................3-449.16 激光单元.............................................................................................................................3-459.17 撮纸辊座组件......................................................................................................................3-479.20 T1离合器组件、定位离合器组件.......................................................................................3-509.21 左主机架组件......................................................................................................................3-529.22 显影驱动辅助组件，显影联结齿轮52................................................................................3-549.23 马达驱动辅助组件，主马达................................................................................................3-569.24 出纸传感器电路板组件.......................................................................................................3-589.25 定影齿轮28/34...................................................................................................................3-60第4章 更换部件后所需的调整和设定值更新...........................................................4-1 1. 如果更换了主板.............................................................................................................4-11.1 设置默认纸张尺寸..................................................................................................................4-11.2 设置序列号.............................................................................................................................4-21.3 输入激光单元的调整值...........................................................................................................4-52. 如果更换了激光单元......................................................................................................4-92.1 输入激光单元的调整值...........................................................................................................4-93. 如果因不规则电源检测出错而更换了低压电源电路板组件............................................4-133.1 重置不规则电源检测计数值..................................................................................................4-13第5章 维修功能......................................................................................................5-1 1. 维修模式........................................................................................................................5-11.1 如何进入用户可使用维修模式.................................................................................................5-11.2 如何进入维修人员专用维修模式.............................................................................................5-11.3 维修模式功能列表..................................................................................................................5-21.4 维修模式功能的详细说明........................................................................................................5-42. 打印机设置..................................................................................................................5-112.1 打印机设置页的打印.............................................................................................................5-113. 其他维修功能...............................................................................................................5-193.1 重新打印功能........................................................................................................................5-193.2 取消打印作业功能................................................................................................................5-193.3 墨粉盒的延续模式/中止模式的设定转换.............................................................................5-203.4 硒鼓清洁功能........................................................................................................................5-20第6章 电路图、接线图...........................................................................................6-1附录1 序列号系统.............................................................................................附录1-1附录2 消去用户设定信息..................................................................................附录2-1Maintenance U SB Printer 驱动程序..................................附录3-1附录3 安装附录4 硒鼓单元保护材料的制作方法................................................................附录4-1规定无线电干扰 (仅适用于220至240V 电压的机型)本设备遵循 EN55022 (CISPR 22通令)/ B级的规定。

Safety Data SheetIssuing date : 20-Dec-2007 SDS # : ICW 0752 R - 04 EU ENRevision date : 30-Sep-2020Version : 07SECTION 1: Identification of the substance/mixture and of the company/undertaking1.1. Product identifier Product name Canon Ink Tank PGI-35 Black Product code(s)1509B1.2. Relevant identified uses of the substance or mixture and uses advised against UseInk for Ink Jet Printer1.3. Details of the supplier of the safety data sheet Supplier ImporterCanon Europa N.V.Bovenkerkerweg 59, 1185XB Amstelveen, The Netherlands +31 20 5458545, +31 20 5458222,**************************Manufacturer Canon Inc.30-2, Shimomaruko 3-Chome, Ohta-ku, Tokyo 146-8501, Japan 1.4. Emergency telephone number *1 Kontakt Giftlinien på tlf.nr.: 82 12 12 12 (åbent 24 timer i døgnet). Se punkt 4 om førstehjælp.*2 Only for the purpose of informing medical personnel in cases of acute intoxications.*3 Ask for Poison InformationSECTION 2: Hazards identification2.1. Classification of the substance or mixtureClassification according to Regulation (EC) No 1272/2008Reproductive toxicity Category 1B 2.2. Label elementsLabelling according to Regulation (EC) No 1272/2008Austria +43 (0) 1 406 43 43 Belgium +32 (0) 70 245 245 Bulgaria +359 2 9154 233 Croatia+385 (0)1-23-48-342 Cyprus 1401Czech Republic +420 224919293 Denmark +45 82 12 12 12 [*1] Estonia 16662Finland +358 (0)9 471977 France +33 (0)1 45 42 59 59 Greece +30 210 7793777Hungary +36 80 20 11 99 Ireland 353 (1) 809-2166/-2566 Italy+39 (0)55 7947819 Latvia+371 67042473 Lithuania +370 (85) 2362052 Luxembourg (+352) 8002 5500Malta 21224071Netherlands +31 (0)30-2748888 [*2] Poland 42 25 38-421/-422/-406 Portugal +351 800 250 250 Romania +40 21 318 36 06 Slovakia +421 2 5477 4166 Slovenia 112 Spain+34 91 562 04 20 Sweden 112 [*3] United Kingdom +44 121 507 4123 Iceland 112Liechtenstein 145 Norway+47 22 59 13 00 Switzerland145Hazard pictogramsSignal wordDangerHazard statementsMay damage fertility or the unborn child.Precautionary statementsNot requiredOther informationContains 1,2-benzisothiazol-3(2H)-one.May produce an allergic reaction.Contains less than 30% of components with unknown hazards to the aquatic environment.UFI: MK50-G09D-900E-P6AD2.3. Other hazardsNoneSECTION 3: Composition/information on ingredients 3.2. MixturesChemical name CAS-No EC-No REACH registrationnumber Weight % Classification (Reg.1272/2008)Note to otherhazardsGlycerin 56-81-5 200-289-5 None 5 - 10 None2-Pyrrolidinone 616-45-5 210-483-1 01-2119475471-37-xxxx 5 - 10 Eye Irrit. 2 (H319)Repr. 1B (H360) Glycol CBI CBI CBI 5 - 10 NoneWater 7732-18-5 231-791-2 None 60 - 80 NoneFull texts of Hazard statement(s) are listed in SECTION 16Note to other hazards : The following substance(s) is (are) marked with (1), (2) and/or (3)- (1) Substance for which EU Occupational Exposure Limit(s) is (are) established (See SECTION 8)- (2) PBT substance or vPvB substance under Regulation (EC) No 1907/2006- (3) Substance listed in Candidate List of SVHC for Authorisation under Regulation (EC) No 1907/2006In case a safety data sheet supplied under (EC) No 1907/2006 Article 31-3 is necessary, please contact us.SECTION 4: First aid measures4.1. Description of first aid measuresInhalation Move to fresh air. Get medical attention immediately if symptoms occur.Ingestion Rinse mouth. Drink 1 or 2 glasses of water. Get medical attention immediately if symptomsoccur.Skin contact Wash off immediately with soap and plenty of water. Get medical attention immediately ifsymptoms occur.Eye contact Flush with plenty of water. Get medical attention immediately if symptoms occur.4.2. Most important symptoms and effects, both acute and delayedInhalation None under normal use. Symptoms of overexposure are dizziness, headache, tiredness,nausea, unconsciousness, cessation of breathing.Ingestion None under normal use. Ingestion may cause gastrointestinal irritation, nausea, vomitingand diarrhea.Skin contact None under normal use.Eye contact None under normal use. May cause slight irritation.Chronic effects None under normal use.4.3. Indication of any immediate medical attention and special treatment neededNoneSECTION 5: Firefighting measures5.1. Extinguishing mediaSuitable extinguishing mediaUse CO 2, water, dry chemical, or foam.Unsuitable extinguishing mediaNone5.2. Special hazards arising from the substance or mixtureSpecial hazardNoneHazardous combustion productsCarbon dioxide (CO 2), Carbon monoxide (CO)5.3. Advice for firefightersSpecial protective equipment for firefightersNoneSECTION 6: Accidental release measures6.1. Personal precautions, protective equipment and emergency proceduresAvoid contact with skin, eyes and clothing.6.2. Environmental precautionsKeep out of waterways.6.3. Methods and material for containment and cleaning upWipe up with adsorbent material (e.g. cloth, fleece).6.4. Reference to other sectionsNoneSECTION 7: Handling and storage7.1. Precautions for safe handlingAvoid contact with skin, eyes and clothing. Clean contaminated surface thoroughly. Use with adequate ventilation.7.2. Conditions for safe storage, including any incompatibilitiesKeep in a dry, cool and well-ventilated place. Keep out of the reach of children. Keep away from direct sunlight. Keep away from heat and sources of ignition.7.3. Specific end usesInk for Ink Jet Printer. Obtain special instructions before use.SECTION 8: Exposure controls/personal protection8.1. Control parametersExposure limitsChemical name EU OEL Austria Belgium Bulgaria Cyprus Glycerin56-81-5None None TWA: 10 mg/m3None None Chemical name Czech Republic Denmark Finland France GermanyGlycerin 56-81-5TWA: 10 mg/m3Ceiling: 15 mg/m3None TWA: 20 mg/m3TWA: 10 mg/m3TRGS TWA: 200mg/m3 inhalablefractionDFG TWA: 200 mg/m3inhalable fractionCeiling / Peak: 400mg/m3 inhalablefractionChemical name Greece Hungary Ireland Italy Netherlands Glycerin56-81-5TWA: 10 mg/m3None None None None Chemical name Poland Portugal Romania Slovakia SpainGlycerin 56-81-5TWA: 10 mg/m3inhalable fractionTWA: 10 mg/m3 mist None TWA: 11 mg/m3TWA: 10 mg/m3 mistChemical name Sweden United Kingdom Norway Switzerland TurkeyGlycerin 56-81-5 None TWA: 10 mg/m3 mist None TWA: 50 mg/m3inhalable dustSTEL: 100 mg/m3inhalable dustNone8.2. Exposure controlsAppropriate engineering controls None under normal use conditions.Individual protection measures, such as personal protective equipmentEye/face protection Not required under normal use.Skin protection Not required under normal use.Respiratory protection Not required under normal use.Thermal hazards Not applicableSECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical propertiesAppearance Black ; LiquidOdor Slight odorOdor threshold No data availablepH 8 - 9Melting/freezing point (°C) No data availableBoiling point/range (°C) No data availableFlash point (°C) > 93.0°C (Tag. Closed Cup.); estimated Evaporation rate No data availableFlammability (solid, gas) Not applicableFlammability limits in airUpper flammability limit None; estimatedLower flammability limit None; estimatedVapor pressure No data availableVapor density No data availableRelative density 1.0 - 1.1Solubility(ies) Water; misciblePartition coefficient: n-octanol/water No data availableAuto-ignition temperature (°C) None; estimatedDecomposition temperature (°C) No data availableViscosity (mPa s) 1 - 5Explosive properties None; estimatedOxidizing properties None; estimated9.2. Other informationNo data availableSECTION 10: Stability and reactivity10.1. ReactivityNone10.2. Chemical stabilityStable10.3. Possibility of hazardous reactionsNone10.4. Conditions to avoidNone10.5. Incompatible materialsAcids, Bases, Oxidizing agents, Reducing agents.10.6. Hazardous decomposition productsCarbon dioxide (CO 2), Carbon monoxide (CO), and/or Ammonia.SECTION 11: Toxicological information11.1. Information on toxicological effectsAcute toxicity No data availableSkin corrosion/irritation Non-irritant (Estimate) (OECD Guideline)Serious eye damage/eye irritation Minimal irritant (Estimate) (OECD Guideline)Sensitization Non-sensitizer (Estimate) (OECD Guideline)Germ cell mutagenicity Ames test: NegativeCarcinogenicity No data availableReproductive toxicity 2-pyrrolidone is classified as a Category 1B (GHS) developmental toxicant.However, the amount of exposure to 2-pyrrolidone is negligible under intended use of thisproduct.STOT - single exposure No data availableSTOT - repeated exposure No data availableAspiration hazard No data availableOther information No data availableSECTION 12: Ecological information12.1. ToxicityEcotoxicity effectsNo data available12.2. Persistence and degradabilityNo data available12.3. Bioaccumulative potentialNo data available12.4. Mobility in soilNo data available12.5. Results of PBT and vPvB assessmentThis preparation contains no substance considered to be persistent, bioaccumulating nor toxic (PBT).This preparation contains no substance considered to be very persistent nor very bioaccumulating (vPvB).12.6. Other adverse effectsNo data availableSECTION 13: Disposal considerations13.1. Waste treatment methodsDispose of in accordance with local regulations.SECTION 14: Transport informationSECTION 15: Regulatory information15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture (EC) No 1907/2006 Authorisation Not regulated (EC) No 1907/2006 Restriction Not regulated (EC) No 1005/2009 Not regulated (EU) 2019/1021 Not regulated (EU) No 649/2012 Not regulated Other informationNone15.2. Chemical safety assessment NoneSECTION 16: Other informationFull text of H-statements referred to under SECTION 2 and 3H319 - Causes serious eye irritationH360 - May damage fertility or the unborn childKey literature references and sources for data- World Health Organization International Agency for Research on Cancer, IARC Monographs on the Evaluation on the Carcinogenic Risk of Chemicals to Humans- EU Regulation (EC) No 1907/2006, (EC) No 1272/2008, (EC) No 1005/2009, (EU) 2019/1021, (EU) No 649/2012 Key or legend to abbreviations and acronyms used in the safety data sheet - PBT: Persistent, Bioaccumulative and Toxic - vPvB: very Persistent and very Bioaccumulative - SVHC: Substances of Very High Concern- EU OEL: Occupational exposure limits at Union level under Directive 2004/37/EC, 98/24/EC, 91/322/EEC, 2000/39/EC, 2006/15/EC, 2009/161/EU, (EU) 2017/164 and (EU) 2019/1831.- TWA: Time Weighted Average - STEL: Short Term Exposure Limit- GHS: Globally Harmonized System of Classification and Labelling of Chemicals - IARC: International Agency for Research on Cancer - IATA: International Air Transport Association - CBI: Confidential Business Information14.1. UN numberNone 14.2. UN proper shipping name None 14.3. Transport hazard class None 14.4. Packing groupNone14.5. Environmental hazards Not classified as environmentally hazardous under UN Model Regulations and marine pollutant under IMDG Code. 14.6. Special precautions for usersIATA: Not regulated14.7. Transport in bulk according to Annex II of MARPOL and the IBC CodeNot applicableIssuing date : 20-Dec-2007Revision date : 30-Sep-2020Revision note SECTION 2, 3, 11, and 16 revisedThis safety data sheet (SDS) is supplied under (EC) No 1907/2006 Article 31-3.DisclaimerThe information provided on this SDS is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guide for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered as a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other material or in any process, unless specified in the text.。

HARMAN technology Limited TECHNICAL INFORMATIONA MEDIUM SPEED BLACK AND WHITE CAMERA FILMKENTMERE PAN 100 is a medium speed black and white camera film which is suitable for a variety of indoor and outdoor photography applications, where good lighting exists. It has the capability to generate high quality images with fine grain and good sharpness and is a good choice of film if enlargement prints are desired.KENTMERE PAN 100 35mm film is coated on 0.125mm/5-mil acetate base and is available in 24 or 36 exposure cassettes, or in bulk lengths of 30.5 metres (100ft). KENTMERE PAN 100 35mm film is supplied in DX coded cassettes, suitable for all 35mm cameras.EXPOSURE RATING KENTMERE PAN 100 has a speed rating of ISO 100/21º to daylight. The ISO speed rating was measured using ILFORD ID-11 developer at 20ºC/68ºF with intermittent agitation in a spiral tank.FILTER FACTORS KENTMERE PAN 100 film may be used with all types of filters (e.g. colour, polarising and neutral density filters) in the usual way. Follow the instructions given by the filter manufacturer.The exposure increase in daylight may vary with the angle of the sun and the time of day. In the late afternoon or the winter months, when daylight contains more red light, green and blue filters may need slightly more exposure than usual. Cameras with through-the-lens metering will usually adjust the exposure automatically when using filters. With some automatic exposure cameras, the correction given for deep red and orange filters can produce negatives under exposed by as much as 1½ stops.MAKING LONG EXPOSURES For exposures between 1 and 1/10 000 second, no adjustments are needed for reciprocity law failure.When exposures longer than 1 second are given,KENTMERE PAN 100, along with other films, needs to be given more exposure than indicated by a meter. Usethe graph to calculate the increased exposure time which should be given once the metered time is known.The graph is based on the formulae Ta = Tm 1.26Ta = Adjusted TimeTm = Metered TimeDEVELOPMENT TIMESThe table below gives development times for both manual and machine processing KENTMERE PAN 100. These times will produce negatives of average contrast suitable for printing in all enlargers. The development times are intended as a guide and may be altered if a different result is needed.For manual processing in spiral tanks and deep tanks, the development times are based on intermittent agitation. Where continuous agitation is used for manual processing (as in a dish/tray or with some types of developing tank), reduce these times by up to 15%. For use in rotary processors without a pre-rinse, reduce the spiral tank development times by up to15%. A pre-rinse is not recommended as it can lead to uneven processing.ILFORD developer Dilution Meter setting (EI)50/18 100/21 200/24Spiral tank, deep tank, dip and dunk machines (min:sec @ 20°C/68°F)ILFOTEC DD-X1+48:30 10:30 12:30 ILFOSOL 31+9− 5:00−1+14− 7:30−ILFOTEC HC1+15− 4:005:00 1+315:00 6:30 8:00 ILFOTEC LC291+9− 4:005:00 1+195:307:008:001+29 7:3011:00−ID-11stock 7:009:0011:00 1+18:3011:3015:301+317:3021:00−MICROPHEN stock− 8:309:00 1+1−10:3014:001+3− 14:30−PERCEPTOL stock9:3012:30−1+113:3015:30−1+3−−−Non-ILFORD Developers (20°C/68°F)Kodak D-76stock 7:009:0011:001+18:3011:3015:301+3 17:3021:00−Dip and dunk machines (24°C/75°F)ILFOTEC DD1+4 7:30 9:00 12:00 ILFOLAB FP40, roller transport and short leader machines (26°C/79°F)ILFOTEC RT RAPID1+1+20:450:500:601+1+50:601:101:30Note. Development times may need adjusting to suit individual processing systems and working practices. If an established system is producing good results, adjust the recommended development times until the desired contrast level is obtained. Development times for some other manufacturers’ developers are included for your convenience and are only a general guide. Other manufacturers can and do change their product specifications from time to time, and the development times may change as a result.Processing at Different TemperaturesKENTMERE PAN 100 film can be processed over a range of temperatures. Development times at temperatures other than 20°C/68°F may be calculated from the charts below. For example, if 4 minutes at 20°C/68°F is recommended, the time at 23°C/73°F will be 3 min and the time at 16°C/61°F will be 6 min.PROCESSINGKENTMERE PAN 100 can be processed in all types of processing equipment including spiral tanks, rotary processors, dishes/trays, deep tanks and automatic processors. Standard capacity figures and replenishment rates can be maintained. KENTMERE PAN 100 is very robust in processing and will tolerate less than ideal processing conditions. Also, it will not contaminate the processing chemicals.Safelight recommendationsHandle KENTMERE PAN 100 film in total darkness.AgitationIntermittent agitation is recommended for use in spiral tanks and deep tanks. With spiral tanks, invert the tank four times during the first 10 seconds, then invert the tank four times again during the first 10 seconds of each further minute. Otherwise, follow the recommendations given by the processing equipment manufacturer.Stop, fix, wash and rinseFor best results it is recommended that all process solutions are kept at the same temperature or at least within 5ºC (9ºF) of the developer temperature.Stop BathAfter development the film can be rinsed inwater, but we recommend that an acid stop bath is used such as ILFORD ILFOSTOP (with indicator dye). ILFOSTOP is also recommended for all machine processing applications. When tanks or dishes (trays) of process solutions are in use a stop bath immediately stops development and reduces carry over of excess developer into the fixer bath. This helps to maintain the activity and prolong the life of the fixer solution. ILFORD ILFOSTOPDilution 1+19 Temperature Range 18–24ºC (64–75ºF)Time (sec) at 20ºC (68ºF) 10-30Capacity (films per litre,unreplenished)15x (135-36)Fix The recommended fixers are ILFORD RAPID FIXER or ILFORD HYPAM FIXER.Wash Wash the films in running water for 5–10 minutes at a temperature within 5ºC (9ºF) of the process temperature. Or see note below for greater economy when using spiral tanks. Note: For spiral tank use, the following method of washing is recommended. This method of washing is faster, uses less water yet still gives negatives suitable for long term storage. After fixing, fill the spiral tank with water at the same temperature, +/– 5ºC (9ºF), as the processing solutions and invert it five times. Drain the water away and refill. Invert the tank ten times. Once more drain the water away and refill. Finally, invert the tank twenty times and drain the water away.Rinse For a final rinse use ILFORD ILFOTOL wetting agent added to water, it helps the film to dry rapidly and evenly. Start by using 5ml per litre of rinse water (1+200), however the amount of ILFOTOL used may need some adjustment depending on the local water quality and drying method. Too little or too much wetting agent can lead to uneven drying. Remove excess rinse solution from the film before drying.Drying To avoid drying marks, use a clean squeegee or chamois cloth to wipe KENTMERE PAN 100 film beforehanging it to dry. Dry KENTMERE PAN 100 at 30–40°C/86-104°F in a drying cabinet or at room temperature in a clean dust-free area.STORAGE For immediate use, store KENTMERE PAN 100 in a cool (10–20°C/50-68°F), dry place in its original packaging.KENTMERE PAN 100 may be stored in a fridge/freezer but allow plenty of time for the film to acclimatise prior to use.Exposed film Once exposed, process KENTMERE PAN 100 as soon as practical.Exposed films should always be stored in cool, dry conditions - as recommended above.Negatives Store processed negatives in a cool (10–20°C/50-68°F), dry place, in the dark. Suitable storage sleeves include those made of cellulose triacetate, Mylar, paper (pH6.5–7.5) or inert polyester.A wide range of fact sheets are available which describe and give guidance on using our products. Some products in this fact sheet might not be available in your country.HARMAN technology Limited , Ilford Way, Mobberley,Knutsford, Cheshire WA16 7JL, EnglandILFORD RAPID OR HYPAM FIXERS Dilution 1+4 Temperature Range 18–24ºC (64–75ºF) Time (mins) at 20ºC (68ºF) 2-5 Capacity (films per litre, unreplenished) 24x (135-36)。

LARGE FORMAT PRINTERSURECOLOR™ SC-F9330Dual Printheads Up to 64” Wide Dual 1.5L Ink Tanks 1 Year Warranty EnvironmentallyFriendly*Based on 360 x 720 dpi 1 pass printing **All speed is dependent on RIP used108.660.127.4The Epson SureColor SC-F9330 dye-sublimation transfer printer delivers high-volume prints using the most advanced technology without wavering on the quality it produces. Fitted with Epson's cutting-edge Precision Media Feeding System, the SC-F9330 ensures outstanding reliability with accurate media feeding and stable continuous printing. The dual PrecisionCore ™printheads and UltraChrome ™ DS ink deliver high quality prints at impressive speeds of up to 108.6 m 2/h*.Trusted ReliabilityThe advanced Precision Media Feeding System delivers ultra-reliable high-volume printing that ensures minimal downtime.Stunning QualitySpecially formulated UltraChrome DS ink and Epson's Precision Dot Technology deliver impeccable prints.Increased ProductivityFast printing speeds of up to 108.6m 2/h * and high capacity ink tanks help to increaseproductivity to make way for more print jobs.High capacity1L ink packs.IT’S IN THE DETAILS.With PrecisionCore printhead technology,Epson SureColor SC-F9330excels with speed and quality.SPECIFICATIONSSURECOLOR™ SC-F9330C11CG4440264"Dual PrecisionCore ™ TFP ® Printhead 360 nozzles x 4 channels x 2 head 720 x 1440 dpiUp to 108.6 m 2/h (360 x 720 dpi)Up to 60.1 m 2/h (720 x 720 dpi)Up to 44.1 m 2/h (720 x 720 dpi)Up to 29.9 m 2/h (720 x 720 dpi)Up to 27.4 m 2/h (720 x 720 dpi)Up to 20.7 m 2/h (720 x 720 dpi)Up to 15.6 m 2/h (720 x 1440 dpi)Epson UltraChrome ™ DS dye-sublimation ink4 colours - Cyan, Magenta, Yellow, High Density Black 1000ml ink pack / 2 x 1500ml ink tank per colourRear roll feed (2" / 3" core with max 250mm diameter and up to 45kg); Auto take-up reel Max printing width: 1615.6mm; Side Margin: 5mm both sides,10mm with media holding guides 300 to 1625.6mm Up to 1 mm 2.7" Colour LCDHi-Speed USB, 10BASE-T/100BASE-TX/1000BASE-T Standard: ESC/P raster 512MB main + 128MB networkBundled in CD (Windows Only): CD installer, Epson communication Driver,Epson manual Launcher, Operators Guide, General Information, Epson Control Dashboard,EpsonNet Setup, EpsonNet Config, EpsonNet Print, Software UpdaterWeb delivery (Mac and Windows):CD installer, Epson communication Driver, Epson manual Launcher, Operators Guide,General Information, Epson Control Dashboard, EpsonNet Setup, EpsonNet Config,EpsonNet Print, Software Updater, LFP Accounting Tool, Wasatch SoftRIPInput voltage AC 100-240V 50/60Hz / 10 - 5AOperating: Approx. 570W; Ready: Approx. 340 W; Sleep:Approx. 14 W; Power Off: Approx. 1.0 W 15 - 35°C; 20 - 80% RH (non-condensing)2,620 x 934 x 1,332 mm (WxDxH) (storage)290kg (without ink)Substrate Support System and Ink Supply System (C12C933401),Initial Ink Pack Set (C12C932461), Wasatch SoftRIP (7110706)1-year limited warrantyPrintheadNozzle Configuration Maximum ResolutionDraft (1 pass)Production (2 pass)Production (3 pass)Production (4 pass)High Quality (5 pass)High Quality (6 pass)High Quality (8 pass)Ink Type Colours Ink CapacityPaper Handling Printable Area Media Width Media ThicknessControl Panel Printer Interfaces Printer Languages Memory SoftwarePower Requirements Power Consumption Recommended Operating Temperature & HumidityDimensions WeightModel Number Printer Width Printing TechnologyPrint SpeedInk SystemPaper HandlingControl Panel Connectivity Memory SoftwarePower and OperatingRequirementsPrinter Dimensions Bundled Items WarrantyDimensions & Weight SC-F9330Weight: 290kg (without ink)1,332mm934mm2,620mmInk Cartridge Compatibility 1L Ink Packs • High Density BlackC13T741X00• Cyan C13T741200• Magenta C13T741300• Yellow C13T741400Supplies & Optional Accessories Cleaning StickC13S090013Clean Room Wiper C13S090016Head Cleaning Set C13S210051Maintenance Kit C13S210063Waste Ink Bottle C13T724000Media Holding GuideC12C932411Dealer’s StampInformation correct at time of printing Printed September 2019© 2019 Epson Singapore Pte Ltd. All Rights Reserved.Reproduction in part or in whole, without the written permission from Epson, is strictly prohibited. EPSON and EXCEED YOUR VISION are registered trademarks of Seiko Epson Corporation. All other product names and other company names used herein are foridentification purposes only and are the trademarks or registered trademarks of their respective owners.Epson disclaims any and all rights in those marks.Print samples shown are simulations only. Specifications and product availability are subject to change without notice and may vary between countries. Please check with local Epson offices for more information.Sales Enquiries800 120 5564For latest specifications, visit .sg/f-series or call 800 120 5564.Epson Singapore Pte Ltd 1 Harbourfront Place, #03-02 HarbourFront Tower One, Singapore 098633. Tel: (65) 6586-5500 Fax: (65) 6271-9755Epson Customer Care Centre 108 Pasir Panjang Road, #04-08 Golden Agri Plaza, Singapore 118535. Epson Helpdesk: 800 120 5564. Operating hours: Monday - Friday, 9am - 6pm, Saturday, 9am - 1pm. Closed on Sunday and Public Holiday.EpsonSEA @EpsonSEA EpsonSoutheastAsia Epson Southeast AsiaEpsonSEA。

化学品安全技术说明书1. 化学品及企业标识产品名HP Color LaserJet CB380A-AC-YC 黑色墨盒公司名称HP Technology (Beijing) Co., Ltd. (HP Technology (Beijing) Co., Ltd.)3F, 112 JianGuo Road,ChaoYang District Beijing, Beijing, China 100022电话号码 (+86) 10 6564-3888HP Inc. health effects line（美国境内免费） 1-800-457-4209（专线） 1-760-710-0048HP Inc. Customer Care Line（美国境内免费） 1-800-474-6836（专线） 1-208-323-2551建议用途及限制使用该产品是用于 HP CLJ CM6030 Series MFP, HP CLJ CP6015 , HP Color LaserJet CM6040 MFP 系列打印机的黑色硒鼓。

推荐用途发布日期09-17-2015填表时间03-17-2016版本号032. 危险性概述GHS GHS分类分类未被分类。

GHS GHS标记标记无。

符 号警示词无。

危险性说明无。

防范说明预防措施无。

事故响应无。

安全储存无。

废弃处置无。

其它危险碳黑被 IARC 列为 2B 组致癌物质（物质可能使人类致癌）。

由于此制剂中的碳黑处于束缚形式，不存在致癌危险。

此制剂中的其他成分均未被 ACGIH、EU、IARC、MAK、NTP 或 OSHA 列为致癌物质。

3. 成分/组成信息纯物质或混合物混合物浓度浓度（%）（%）登记号(登记号(CAS CAS CAS号)号)化学名称貿易秘密<85乙烯一丙烯酸脂共聚物貿易秘密<15蜡1333-86-4<6碳黑7631-86-9<2二氧化硅4. 急救措施吸入立刻将人员移动到通风处。