PLY300使用说明书(打印版)

MVP300智能电气阀门定位器 Intelligent Electropneumatic valve Positioner用户手册User Manual1 用户须知1.1安全指示定位器先上电，后供气源； 产品使用过程中，不要随意的触摸； 产品必须正确安装、正确操作和正确维护。

1.2 开箱清单MVP300智能阀门定位器； 安装配件； 用户手册；另外订制附件，详见装箱清单。

1.3 重要信息提示为了您能更好地应用这份说明，以及保障你在调试，运行和维修这台仪器时的安全，请注意下列符号的用途：符号标语 解说注意 注意指潜在的危险，如不能避免，可能会损害产品本身或周围物体。

（危险物）提示 提示是指有用的或特别的被忽视的能影响操作条件或产品功能的事物。

（不包含危险的或有害的情形）在安装和调试前请认真阅读此手册。

2 概述MVP300智能阀门定位器是一种二线制现场仪表。

本定位器作为气动阀门的配套控制部件，广泛运用于石油、化工、电力、冶金、轻工等领域的自动控制系统中。

MVP300智能阀门定位器接受来自控制系统的4~20mA 阀位设定信号，通过A/D 转换得到阀位设定值；同时通过位置传感器得到实际的阀位信号;两者经过控制软件的计算处理，从而控制气动执行机构的进气与排气，驱动阀位到达设定点（如图1所示）MVP300智能阀门定位器是基于微处理器技术的高性能电/气阀门定位器，能很好地克服摩擦力和阀芯上的不平衡力，提高调节阀的响应速度，使其定位迅速准确。

它不仅完全能替代传统的电/气阀门定位器，而且可直接接入HART 协议网络，实现与控制系统的信息交换。

图1：型智能阀门定位器原理框图2.1 功能介绍自适应功能：自动寻找阀门零点和满度，优化阀门控制参数, 提高控制精度组态功能： 可设置阀门特性曲线、动作方式、死区、行程范围、关断值、事件输出自诊断功能：能显示输入电流值、上/下行程时间、死区、预判值等故障模式：故障时定位器可选择 全开、全关、保持、手动等模式通讯功能：HART协议的通讯功能电流反馈功能：输出4~20mADC阀位反馈信号2.2 特点定位精度高，达0.5%F.S操作无需开壳，高防护等级下实现真正的就地操作具有本质安全型防爆，性能安全可靠结构简单，体积小，可安装在小型执行机构上自动整定，自动诊断，阀门特性曲线可组态设定机械零件少，抗振性能好；可就地或远程进行参数设置；低功耗、低耗气量、低运行成本；采用二线制4~20mA标准信号；3 技术参数气源压力 0.14～0.7 Mpa气指标阀泄漏量 < 0.8L / H稳态耗气量 < 36L / H适应执行机构 单作用、双作用行程范围 直行程10～100mm；角行程30～150º电流输入 4～20mA DC，最小输入电流>3.6mA；可设定分程控制起点和终点反馈输出 4～20mA DC输入输出开关输入 干节点，用于自保联锁功能开关输出 2路24V 2A行程开关，2路电子开关压电阀开关动作次数 平均无故障动作次数 > 20亿次输出特性修正 线性、等百分比（1：25，1：33，1：50）、快开、用户自定义20段曲线通讯方式 HART通讯协议液晶显示 2排7位数字液晶，尺寸22*38mm显示方式开度显示 0-100%，旋转的开度指示压力表显示 可选配2-3个压力表，显示进出口空气压力组态操作 自整定 自整定阀门零点及满量程，最小死区(自动值)和最小预判（自动值）自诊断可对整定过程，阀位超限，阀门堵转等数据进行诊断就地手操 前面板3个按键，可就地手动操作阀位开度死区 0.1～10% 可调整线性度0.5% FS 灵敏度 0.2% FS 精度重复性 0.5% FS 环境温度 -20～70℃ 环境湿度5～95%RH 抗振性能 15～150Hz/2g防护等级 IP65 工作环境防爆等级 Ex ia ‖C T4~T6重量2 .0 Kg 尺寸 170×96×96 mm外形外壳材质铝合金4 安装说明4.1 外形尺寸图2：智能阀门定位器外形尺寸图4.2 机构安装4.2.1直行程定位器安装连接直行程安装元件列表序号 数量 名称 规格1 6 六角头螺栓 M8×162 6 弹簧垫圈 D83 6 平垫圈 D84 1 执行器连接板5 1 定位器连接板6 2 内六角圆柱头螺钉 M6×257 2 弹簧垫圈 D68 2 平垫圈 D69 1 U型连接杆10 2 夹紧块11 2 十字槽盘头螺钉 M5×1612 2 弹簧垫圈 D513 2 平垫圈 D514 1 中心连接杆15 1 控制杆部件定位器安装在执行机构的正前方。

TYE-300型压力试验机说明书TYE-200300型压力试验机说明书尊敬的用户：您好！感谢您使用我公司全自动恒加载水泥压力试验机，由于TYE-200型以及TYE-300型两种压力试验机在外形、结构上基本相同，且操作方法相同，只是在本说明书中列出的操作显示界面上略有差别，在自动标定和闭环打点检测两项上由于TYE-200型只能加载至200kN，比TYE-300型少操作两点（250kN和300kN）。

因此，本说明书以介绍TYE-300型压力试验机为主，其中微小差别不会影响操作使用，请用户谅解。

一、概述：本机专供测定水泥胶砂抗压强度之用，最大载荷（200/300）kN，本机具有精度高、结构紧凑、操作简单等优点，是水泥厂、建筑工程单位、产品质量监督检验站、大专院校必不可少的设备。

本产品执行标准：GB/T 3722 《液压式压力试验机》JB/T 8763《电液式水泥压力试验机技术条件》。

二主要技术参数：1.最大试验力（200/300）kN2.测量范围0～(200/300)kN3.自动恒速加载时计算机显示a）零点相对误差±0.1%b) 加载速度误差±7%c) 试验机预热30分钟后,在15分钟内的零点漂移不超过满量程的±0.2%。

d）调速范围（0.3～9.9）kN/s4.示值相对误差±1%5.活塞直径Φ125mm6.压板间净距离280mm7.压板直径Φ150mm8.整机功率 1 kW9.外形尺寸(长×宽×高) （562×458×1475）mm10.净重400kg三结构原理：本机由机架、油泵、比例阀、控制箱和计算机系统组成，机架、油泵和比例阀安装于底座上构成一个整体。

计算机系统安放于计算机操作台上通过连接导线与比例阀连接。

1.机架部件(如图1)机架部件由底座（1）、横梁（9）和立柱（2）连成一个整体。

横梁（9）下装有凹球座（8）和上承压板（7）；底座上装有油缸（3）、活塞（4）、下承压板（6）和防尘罩（5）；上下压力板的平行均靠凹球座调整。

LW-PX300Cost-effective • Intuitive • User-friendlyThe Epson LABELWORKS LW-PX300 provides an industrial-grade labeling solution at an entry-level price. For those seeking a low-cost, compact wire-marking, bar-code and general-identification label solution for creating custom and compliant labels up to 3/4” (18 mm) wide, the LW-PX300 delivers. Identify wires and equipment, organize tool boxes or shelves, or add content information to storage bins. With the LW-PX300, you can print on a variety of materials such as magnetic tape, heat shrink tube, and strong adhesive tape. And like the entire Epson LABELWORKS product line, the LW-PX300 is backed by our industry-leading lifetime warranty.Backlit LED screenQWERTY keyboardCompact, handheld designLabel-customizing shortcut keysOne-touch cutterPre-loaded industry symbolsFEATURES AND FUNCTIONSALL LABELWORKS PX PRINTERS COME WITH AN INDUSTRY-LEADINGLIFETIME WARRANTYHot KeysProfessional ChoiceCapable and ProductiveLightweight and CompactCompact and lightweight, the LW-PX300 boasts affordability and simplicity paired with functional efficiency. Its features include: QWERTY keyboard, pre-loaded symbols and formatting options, cross-printer compatible cartridges, and print capability for all materials (including heat shrink tube and magnetic tape).The LW-PX300 prints up to 3/4” wide (18mm) on standard and specialty tape, and up to 3/16”on heat shrink tube. Plus, you’ll find the essential features and functions needed for printing cost-effective industrial labels in the field or around the workplace.Industry-specific hot keys built into the LW-PX300 save time while labeling. Plus you can quickly access hundreds of industrial symbols, fonts, language characters, templates and styles to make formattingyour industrial labels a breeze.Slightly larger than the size of a mobile phone! Carry it anywhere labeling is needed.LABELWORKS PX •370SMCDrive,POBox309•Somerset,WI54025••*********************.com•800.622.6312TAPE LINEUPLABELWORKS PX LW-PX300Industry-Leading Savings • Industry-Leading WarrantyStrong Adhesive - NEW! Vinyl Tape - 30’Shrink Tube - 96”Fluorescent - 30’Compliance Standards: UL Standard 224 (Related Temperature: 125º C,SPECIFICATIONSLABELWORKS PXLW-PX300LW-PX300VP Kit SKU: LW-PX300VP• LW-PX300 printer • AC Adapter• 212BWPX tape cartridge • Rubber drop guard • User guide• Industrial carrying caseDealer’s StampInformation correct as of October 2019© 2019 Epson LABELWORKS PX. All Rights Reserved. Reproduction in part or in whole, without the written permission from Epson, is strictly prohibited.EPSON and EXCEED YOUR VISION are registered trademarks of Seiko Epson Corporation. All other products names and other company names used herein are for identification purposes only and are the trademarks or registered trademarks of their respective owners. Epson disclaims any and all rights in those marks. Print samples shown are simulations only. Specifications and product availability are subject to change without notice and may vary between countries. Please check with local Epson offices for more information.Printing Thermal Transfer Technology Tape Width 6-18 mm Resolution 180 dpi Printer head width 9.3 mmMax Print Speed 6mm / sec (With AC Adapter)Store Files Up to 50 files Print Settings No Repeat Printing Auto Increment No Data Import No Number Serialization Yes Mirror Printing No Vertical Printing No Mix Length NoMargins Minimum 10 mm lead on standard industrial tapes. Fixed Length Auto / Custom Cable Wrap No Flag Yes QR Code NoBarcodes 8 types: EAN 8, EAN 13, Code 39, Code 128, UPC-A, UPC-E, ITF, CodaBar Symbols 859 industrial and professional symbolsHardware ManualCutter DetectionTape Detection (Type and size)Drop-Stop & Pick-and-PrintNoLCD140 x 80 dot back-lit monochrome LCDOther Information AC Adapter Yes, in LW-PX300VP Kit Only Battery6AA (Not Included)LW-PX300 Basic Kit SKU: LW-PX300• LW-PX300 printer• 212BWPX tape cartridge • User guide。

N | SIXPAR 300™ | user manualSIXPAR 300™user manualw w w. e l a t i o n l i g h t i n g . c o m©2019 ELATIONdiagrams,ELATION PROFESSIONALare trademarks of ELATION PROFESSIONAL.all forms andstatutory ordocumentcompanies and are hereby acknowledged.names are trademarks or registered trademarks of their respective companies.C O N T E N TGeneral InformationG E N E R A LINTRODUCTIONCongratulations,reliablebeen designedWARRANTY REGISTRATIONPlease fill out the enclosed warranty card to validate your purchase. All returned serviceaccompanyclearlyproblempaper and included in the shipping container. If the unit is under warranty, youL I M I T E D W A R R A N TA. Elationbe free of manufacturing defectsand Elation Professional® pmaterial andThis warranty if the productS A F E T YDIRECTL Y WITH OPTICAL INSTRUMENTSINDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, INDIVIDUALS U S I N G PHOTOSENSITIVE MEDICATION, ULTRAVIOLET UV LIGHT EMITTED FROM THE UV LED.IMPORTANT NOTICE!There arey o u r s eresultinggeneralG E N E R A LN E V E R•During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and willF I X T U R Ew w w. e l a t i o n l i g h t i n g . c o m F I X T U R E I N S T A L L A T I OMOUNTING POINTS•Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.S A F E T Y C A B L EAlways use a Safety Cable whenever installing this fixture in a suspendedenvironment to ensure the fixture will not drop if the clamp fails.U N D E R S T A N D I N GDMX-512DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controllerand controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all thew w w. e l a t i o n l i g h t i n g . c o mDMX-512 CONTROLLER CONNECTIONConnect the provided XLR cable to the female XLR output of your controller and the other side to the male XLR input of thetypical DMX-512chain multiple panels together through serial linking. Always be sure daisy chain your in and out data connections, never split or “Y” your DMX connections.DMX ADDRESSINGAll fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control informationaddress isF I X T U R E M E NON-BOARD SYSTEM MENUThe SIXPAR 300™will cover how to access each menu function.LCD CONTROL PANEL DISPLAYINFORMATION DISPLAYED DURING INITIAL POWER ONWhen the fixture is initially powered ON, the display shows the following information:LCD CONTROL PANEL LOCKOUTWhen AutoLockand the Control Panel will lock and the display will show Press and hold theWhen AutoLockand theTo unlock the Control Panel, follow these steps:DIMMING CURVESThe DimCurveStandard, Stage, TV, Architec,DimmerD M XMODE / CHANNEL6 CH7 CHMODE / CHANNEL6 CH7 CHMODE / CHANNEL 6 CH7 CHC L E A N I N GT E C H N I C A LFEATURES15° Beam 25° Field Angles5 Variable Dimming Curve Modes Dual Yoke / Floor StandMultiple Unit Power LinkingRDM - Remote Device Management Rugged Die-Cast Aluminum Exterior Flicker Free Operation for TV and FILMPlease Note: SpecificationsPHOTOMETRIC DATADIMENSIONAL DRAWINGSO P T I O N A LORDER CODETRIGGER CLAMPSIXPAR300/GFHSIXPAR/BD300。

NYL—300型压力试验机说明书一．用途NYL—300型压力试验机供测定水泥、砖及石块等建筑材料抗压强度之用。

最大载荷300kN。

本机示值分度小、活塞行程大、工作适应性强，而且结构紧凑、造型新颖、操作简便。

配上合适的抗折夹具后也可作混凝土等材料的抗折强度实验二．技术参数1．最大试验力300kN2．测量范围0~60kN0~150kN0~300kN3．度盘分度值0~60kN时0.2kN/格0~150kN时0.5kN/格0~300kN时1kN/格4．承压板间净距280mm5．承压板直径ф150mm6．活塞直径×最大行程(φ125×120)mm7．油液最高压力25MPa8．示值相对误差±1%9．电机功率0.8kW10．外形尺寸（长×宽×高）(1050×640×1500) mm11．活塞的最大上升速度62 mm / min12．净重800kg13．毛重880kg (木箱)三、构造本机由机架、测力、示值、油泵、送油及回油阀等部件组成，各部件均安装于一个座箱上构成一个整体。

１．机架部分如图（一）所示，底座（９）与横梁（１）借两根立柱（３）连成一个固定整体，横梁腹部装有上压力板（２），它不能调节上下。

而固定在底座上的工作油缸（７）其活塞（８）可上升(120~130)mm，当活塞上升时，为防止粉尘进入油缸而备有防护罩（6）。

当试件通过抗压夹具放在下压力板（４）上时，下压力板的底部具有球面与凹球座（5）接触，因此，可以自动调整上下压力板的平行，使试件受力均匀。

工作油缸与工作活塞是精密偶件，在油缸的内壁上部嵌有复合密封圈（微量溢油是允许的，油缸壁上专门设有溢油通道），这种结构可以使工作油缸与活塞之间的摩擦减少到极小限度，从而保证了试验机的精度。

上、下压力板均经热处理后磨平，下压力板的圆刻线直径ф101是帮助操作者放置试件及抗压夹具时对准中心。

２．测力机构（图三）本机采用的液压摆锤测力机构，它与示值机构一起组成测力系统。

INLAND COATINGS CORPORATION Array SYSTEM SPECIFICATION FOR EPDM SINGLE PLYThis specification provides a strong, flexible, synthetic rubber membrane that is resistant to water, corrosion and weather extremes. It can be used for mechanically fastened and/or fully adhered single ply EPDM systems.It provides a white, reflective finish coat that is an Energy Star labeled product and dramatically reduces roof temperatures. This keeps the building cooler and eliminates expansion and contraction related problems. The end product shall be a seamless, elastomeric system protecting the roof against leaks and degradation by the elements.NOTE: Inland RC 2000 and RC 2200 are solvent-based products. Care should be taken when applying them over EPDM membranes to prevent wrinkling on seams and other surface areas. The published application rates and procedures should be followed.Note: As Inland's high reflectance systems have a significant cooling effect on roofing surfaces,the building envelope should be evaluated to ensure that the insulation and vapor barrier are adequate to prevent condensation development on interior surfaces.Part 1. - GENERAL1.01 DESCRIPTIONA.Work included: The contractor will provide all labor, materials and tools as required to prepareand complete the installation with new materials as specified. All workmanship shall conformto the material manufacturer’s recommendations and accepted industry standards.B.The installation to include sealing of roof joints, including but not limited to seams,penetrations, drains and scuppers. All preparatory work will then be encapsulated with RC 2000 Rubber Roof Coating.1.02SUBSTRATE CONDITIONSA.The pre-existing roofing system must be intact with no material or structural defects. It must beadequately bonded to the substrate and the insulation must be free from moisture. Seams mustbe well adhered or re-seamed using similar materials. If moisture is suspected, obtain amoisture content survey. Remove and replace moist and inadequately bonded insulation.B. This specification does not apply to loose-laid, ballasted or previously coated EPDM systems.C.All pre-existing roofing must have sufficient slope (at least ¼” to the foot) to eliminate pondingwater.D.The substrate must be free of splits, blisters, grease, oils and debris.E. It is not recommended that Inland products be applied over brittle or friable membranes. Slightscrim exposure is acceptable.F.The Inland system is not intended for use on heavy traffic bearing substrates. If foot traffic isexpected, a rooftop walkway system shall be used which is approved by Inland.1.03 QUALITY ASSURANCEA.Manufacturer Qualifications: Provide primary products, including Inland RC 2000 RubberRoof Coating, RC 2200 Rubber Seam Compound, etc., by a single manufacturer which hasproduced these products successfully for not less than ten (10) years. Provide secondaryproducts only as recommended and approved by Inland Coatings Corporation.B.Contractor Qualifications: A single qualified contractor shall perform all work addressed in thissection. On System Warranted projects, the contractor must be trained and certified by InlandCoatings Corporation for application of the EPDM Single Ply System.1.03 SUBMITTALSA. Submit Ma nufacturer’s literature and samples to the Owner or Owner’s Representative. Literatureon the protective coating, seam compound, reinforcement mesh and other related products shall be submitted for review before work is started. Literature shall show material specifications, physical properties, installation instructions, Manufacturer’s estimated application rate for required dry film thickness per warranty requirements and MSDS.B.Submit a sample copy of the Coating Manufacturer’s warranty to meet proje ct specification.1.05 PRELIMINARY PROJECT REVIEW (System Warranted Projects)A.Immediately after contract award, contractor shall submit a complete and accurate Bid Report to theInland Warranty Department for approval. This should include pages 1 & 2 of the Inland ProjectProfile report, a copy of the roof drawing and the following pictures with detailed descriptions:1.Distant shot of entire building.2.Roof height shot of overall project.3.Close-up of penetrations, scuppers and drains.4.Any unusual flashing or problem areas.1.06JOB CONDITIONSA.Proceed with roofing work only when existing and forecasted weather conditions will permit work tobe performed in accordance with manufacturer’s requirements as follows:1.Do not begin work if rain is expected within six hours of application.2.Do not begin work if surface temperature is above 140 degrees Fahrenheit or below 40 degreesFahrenheit, or when the dew point is less than 5 degrees Fahrenheit above the surface temperature.3.No moisture, dirt, oils or other contaminates can be present when applying products.4.Do not atomize coating when wind velocity is above 15 m.p.h.1.07FIELD QUALITY CONTROLA.The overall weather conditions, including roof surface temperature, ambient air temperature, relativehumidity, dew point and wind velocity shall be recorded daily by the Contractor on the Project Profile form.B.Inspections: A minimum of two (Beginning and Final) inspections, by an approved manufacturersrepresentative, will be required on all projects requiring a System Warranty. The first to be conducted at the beginning of the project, after all surface preparation is completed and prior to the application of any Inland products. The Final inspection will be conducted at the end of the project, after all product applications are completed.C.Verification of Coating Thickness: The wet film thickness shall be measured and recorded daily,along with the quantity of product and total square feet applied.1.08 WARRANTYProvide Inland Product or System Warranty per the requirement of the Building Owner and/or Architect. In order to obtain any Inland System Warranty, the following conditions apply:A.Determination of the appropriateness of the Inland Roofing System for any given roof must be obtainedfrom Inland’s Warranty Department prior to offering any Inland System Warranty. Inland will refuse to offer a warranty on any Inland System being installed over an unfit, unsound or inappropriatesubstrate. A project approval letter must be received from Inland prior to beginning the project.B.The Inland Roofing System must be applied to the full area of the roof. A System Warranty will not beissued for installations over a section of any roof unless otherwise approved in advance by the Inland Warranty Department.C.All gutters and roof areas which pond water for more than 48 hours after precipitation ceases areexcluded from coverage under the Inland Warranty.D.All required forms, applicable warranty fees and the completed Warranty Registration Form, signed bythe Contractor and Building Owner, must be returned to the Inland Warranty Department no later than30 days after the completion of the project.1.09 PRODUCT HANDLINGA.Deliver only approved materials to the job site. Deliver materials in original sealed containers withseals unbroken and labels legible and intact.B.Store and handle materials in a manner that shall ensure there is no possibility of contamination.Store in a dry, well-ventilated, weather-tight place, at temperatures between 50° F and 90° F. Do not stack material pallets more than two high. Do not subject existing roof to unnecessary loading of stockpiled materials. In all cases the storage and handling of materials shall conform to the requirements of the manufacturer and all applicable safety regulatory agencies.C.Any damaged materials, or materials not conforming to the specific requirements, shall be rejected bythe owner. Rejected materials shall be immediately removed from the job site and replaced at no cost to the owner.Part 2. – PRODUCTS2.01RUBBER ROOF COATINGA.Rubber Roof Coating products physical specifications and minimum performance criteria shall be asfollows:1.RC 2000 Rubber Roof CoatingDrying Time: 1 – 3 hoursElongation: 500 percent (ASTM D-412)Tensile Strength:1520 PSI (ASTM D-412)Coverage Rates: 80 – 100 sq. ft/galPermeance: .166 perms (ASTM E-96)Reduction: NoneSpecific Gravity: 1.02Flash Point: 101° F.Solar Reflectance (white): 80+%2.RC 2200 Rubber Seam Compound(Brush, Trowel or Spray Grades)Elongation: 530 percent (ASTM D-412)Tensile Strength:1780 PSI (ASTM D-412)Permeance: .148 perms (ASTM E-96)Reduction: NoneSpecific Gravity: 1.03 to 1.05Flash Point: 81° F. to 101° F.3.RPM Series Polyester MeshA.Stitchbonded polyester mesh for reinforcement of seams and penetrations. Provides high strength and good elongation, while conforming well to irregular surfaces.Tensile Strength: 57.1 PSI (ASTM D1682)Elongation: 61% (ASTM D1682)Mullen Burst: 176 lbs. (ASTM D3786)Trapezoid: 16 lbs. (ASTM D1117)4.CR 2100 Rubber Skylight CoatingA. Clear, flexible rubber coating that provides excellent adhesion and water resistance for fiberglassskylight panels.Drying Time: 1 – 3 hoursElongation: 400 percent (ASTM D-412)Tensile Strength:1520 PSI (ASTM D-412)Coverage Rates: 80 – 100 sq. ft/galPermeance: .166 perms (ASTM E-96)Reduction: NoneSpecific Gravity: .87Flash Point: 101° F.5.RC 300 Roofing Cleaner/DegreaserA.An alkaline cleaner that is biodegradable and non-flammable, which cleans and degreases variousroofing surfaces.6.RST Series Roofing Seam TapeA. A strong, flexible seam tape for reinforcement of seams and penetrations. Provides good elongationand conforms well to irregular surfaces.Solid Content (ASTM D1729-69): 99.8%Tensile Strength (ASTM D-412): 35 PSIElongation/webbing: 200%Cold Temperature Flexibility: PassesMoisture Vapor Transmission: 0.75 perms2.02MANUFACTURERA.The following roof coating manufacturers have been approved for the project. No substitutions bysecondary, indirect manufacturers will be allowed.1.Inland Coatings Corporation2619 Hwy 6Adel, IA 50003(800) 456-8467B. Other manufacturers requesting approval must submit acceptable information certifying that they arethe direct manufacturer from raw material into the specified product and meet the performance criteria required.PART 3.0 - INSTALLATION3.01 SURFACE PREPARATIONA.Examine substrate to receive new roofing. Do not proceed with installation of the Inland RoofingSystem until unsatisfactory conditions have been corrected in a manner acceptable to the manufacturer (Inland Coatings Corporation).B.Contractor shall address the following:Treatment of Deteriorated/damaged membraneTreatment of ponding water areasThorough cleaningMiscellaneous itemsC.Treatment of Deteriorated/Damaged Membrane: Areas that are cracked ,torn or buckled must berepaired using similar materials. Wet insulation must be replaced.D.Treatment of Ponding Water Areas: Contractor shall make every effort to mechanically eliminate allponding water areas on the roof prior to application of products ("ponding water" is defined as water which does not properly drain and remains for more than 48 hours after precipitation stops).E.Thorough Cleaning: The entire roof surface shall be carefully power washed with an approximateworking pressure of 2,000 PSI to remove dirt, chalking or loose materials. Care must be taken to prevent membrane damage and to ensure that water is not forced into the roof system. Power washing will include a strong biodegradable alkaline detergent (Inland RC 300 Cleaner/Degreaser) to improve cleaning and kill any algae or fungus. Surface must be thoroughly rinsed with fresh water and completely dry prior to any product applications.1.Dilute RC-300 Cleaner/Degreaser at the rate of 1 part RC-300 to 30 parts water. Apply the dilutemixtures to all single ply surfaces under low pressure spray at the rate of 200 sq. ft. per gallon. After allowing to sit for a minimum of 30 minutes, rinse thoroughly with fresh water under high pressure (approximately 2000 PSI) to remove solution from the roof.2.Heavy deposits of dirt or contamination may require additional cleaning or mechanical scrubbingwith a stiff bristle broom or brush.F.Air conditioning units, blowers and evaporative coolers shall be disconnected or otherwise modifiedto prevent contaminating the roof surfaces with water or condensation, and to prevent solvent fumes from entering the building.3.02 SEAMS, FASTENERS AND PENETRATIONS (Mandatory on System Warranties)(Method 1 with RPM Series Polyester mesh)A.Fasteners: Coat all fasteners with a liberal amount of RC 2200 Rubber Seam Compound. (Brush,Trowel or Spray Grade). All fasteners must be totally encapsulated.B.Seams: All seams should be coated with RC 2200 Rubber Seam Compound at a coverage rate of 40sf/gal. (A 5” wide pattern should yield 90 lft/gal @ 17 mils DFT). The above coverage rates are to be achieved in a two-coat application and the minimum Dry Film Thickness (DFT) requirements under this specification.1.The application of RC 2200 should be centered on the seam, overlapping an equal distance on eitherside of the seam to accommodate the width of the polyester mesh.2. Embed RPM 400 Polyester Mesh (4” wide) into the seam compound. Back-brush the RPM 400polyester using a stiff bristle brush to prevent wrinkling or air pockets under the fabric. Allow seam area to cure a minimum of 24 hours or until wrinkle free. A second coat of RC 2200 Rubber Seam Compound is then applied over the RPM 400. The Spray or Brush Grades normally provide the best results.C. Penetrations and Flashings: Flash all curbs, crickets, rakes, parapet walls, ridgecaps, vent pipes,skylights, etc. with RC 2200 Rubber Seam Compound, then embed RPM 400 Polyester Mesh (4”wide). Cover the RPM 400 mesh with a liberal coat of RC 2200 Rubber seam compound.D. Skylights: Coat all fiberglass skylight panels with CR 2100 Rubber Skylight Coating at a rate of 100sf/gal. This is best accomplished using a roller or brush.E. Gutters: Apply RC 2200 Rubber Seam Compound and RPM 400 Polyester Mesh to all interior gutterseams. Gutter must be clean and dry before application.3.03SEAMS, FASTENERS AND PENETRATIONS (Mandatory on System Warranties)(Method 2 with RST Series Roofing Seam Tape)A.Fasteners: Coat all fasteners with a liberal amount of RC 2200 Rubber Seam Compound. (Brush,Trowel or Spray Grade). All fasteners must be totally encapsulated.B.Seams: Carefully apply RST-400 Roofing Seam Tape to the seam area and work into all cracks andcrevices to prevent wrinkling or air pockets. Apply a liberal coat of RC-2200 Seam Compound at a coverage rate of 60 s.f./gal. (A 5” wi de pattern should yield 140 lft/gal @ 12 mils DFT) The combined minimum Dry Film Thickness (DFT) required under this specification shall be 30 mils.1.All seaming applications should be centered on the seam, overlapping an equal distance on either sideof the seam.C. Penetrations and Flashings: Flash all curbs, crickets, rakes, parapet walls, ridge caps, vent pipes,pinholes on metal panel, skylights, etc. with RST-400 Seam tape (4” wide). Cover the RST-400 tape with a liberal coat of RC 2200 Rubber seam compound.D. Skylights: Coat all fiberglass skylight panels with CR 2100 Rubber Skylight Coating at a rate of 100sf/gal. This is best accomplished using a roller or brush.E. Gutters: Apply RST-400 Seam Tape to all interior gutter seams. Cover the RST-400 tape with a liberalcoat of RC 2200 Rubber seam compound. Gutter must be clean and dry before application.3.04 COATING APPLICATIONA.Prior to the application of RC 2000 Rubber Roof Coating, all preparation materials shall be allowedto dry sufficiently to prevent damage from spray hoses, foot traffic, etc.B.Immediately prior to the application of RC 2000 Rubber Roof Coating, all dust, dirt or othercontaminates shall be blown off the roof surfaces. Surface must be clean and dry prior to any coating applications.C.The color of the finish coat (The final or last coat to be applied) shall be white.D.The entire roof, including interior gutter surfaces, shall receive RC 2000 Rubber Roof Coatingapplied as follows:Note: Although RC 2000 and RC 2200 provide excellent water resistance, the products must be allowed to cure prior to being subjected to ponding water. It is recommended that standing water be blown or swept from any ponding areas for the first 14 days.Use the following application rates only if specifying a 5-Year Product Warranty1.Apply a flash coat of RC 2000 Gray at a rate of .5 (1/2) gallon per 100 sq. ft. This will minimize anywrinkling of the membrane. Allow membrane to set until wrinkle free.2.Apply finish coat of RC 2000 White at a minimum rate of 1.0 gallon per 100 sq. ft. It should not beapplied unless the base-coat is clean and dry and the membrane is wrinkle free. Allow a minimum of24 hours drying time prior to allowing foot traffic or inspection of the roof surface. The minimumdry film thickness shall be 8 mils.Use the following application rates only if specifying a 10-Year Product Warranty1.Apply a flash coat of RC 2000 Gray at a rate of .75 (3/4) gallon per 100 sq. ft. This will minimizeany wrinkling of the membrane. Allow membrane to set until wrinkle free.2.Apply finish coat of RC 2000 White at a minimum rate of 1.25 gallons per 100 sq. ft. It should notbe applied unless the base-coat is clean and dry and the membrane is wrinkle free. Allow a minimum of 24 hours drying time prior to allowing foot traffic or inspection of the roof surface. The minimum dry film thickness shall be 10 mils.Use the following application rates only if specifying a 10-Year System Warranty1.Apply a flash coat of RC 2000 white at a rate of .75 (3/4) gallon per 100 sq. ft. This will minimizeany wrinkling of the membrane. Allow membrane to set until wrinkle free.2.Apply base-coat of RC 2000 Gray at a minimum rate of 1.0 gallons per 100 sq. ft. It should not beapplied unless the flash coat is clean and dry and the membrane is wrinkle free. Allow a minimum of24 hours drying time prior to allowing foot traffic or inspection of the roof surface.3.Apply Finish coat of RC 2000 White at a minimum rate of 1.0 gallons per 100 sq. ft. It should not beapplied unless the base coat is clean and dry and the membrane is wrinkle free. Allow a minimum of24 hours drying time prior to allowing foot traffic or inspection of the roof surface. The minimumdry film thickness shall be 13 mils.3.05 CLEANUPA.Maintain work areas in a clean, safe condition at all times during coating installation. Removeexcess materials, trash and debris from the job site daily.B.At the completion of the project, clean area of any spills and containers and clean up all roofingdebris, leaving job site in a clean and orderly condition.File Nunber:ISP275E-0610.doc。

MTI300 使用手册：让你的生产更高效随着工业自动化的发展，越来越多的企业开始使用自动化设备来提高生产效率。

而MTI300 就是其中的佼佼者。

MTI300 是一款由德国公司 Festo 开发的全自动化控制系统，它可以实现多种工业生产过程的自动化控制，从而提高生产效率，降低生产成本。

我们将详细介绍MTI300 的使用方法和优势，帮助您更好地了解这款设备，从而为您的生产提供更高效的解决方案。

MTI300 的使用方法MTI300 是一款功能强大的自动化控制系统，但是它的使用方法却非常简单。

您需要将MTI300 连接到您的生产线上。

MTI300 支持多种通信协议，包括 Modbus、Profibus 和Ethernet 等，因此您可以根据您的需要选择合适的通信协议。

接下来，您需要编写控制程序，以实现对生产过程的自动化控制。

MTI300 支持多种编程语言，包括Ladder Logic、Function Block Diagram 和 Structured Text 等，因此您可以根据您的需要选择合适的编程语言。

编写好控制程序后，您就可以通过MTI300 的人机界面进行调试和监控。

MTI300 的人机界面非常友好，您可以通过它实时监测生产过程，调整控制参数，从而实现对生产过程的精确控制。

MTI300 的优势MTI300 的优势主要体现在以下几个方面：1.高效性：MTI300 可以实现对多种工业生产过程的自动化控制，从而提高生产效率，降低生产成本。

MTI300 的控制精度非常高，可以实现对生产过程的精确控制，从而保证产品质量。

2.稳定性：MTI300 的硬件和软件都经过严格的测试和验证，具有很高的稳定性和可靠性。

MTI300 支持多种故障检测和报警机制，可以快速发现和解决故障，从而保证生产线的稳定运行。

3.灵活性：MTI300 支持多种通信协议和编程语言，可以适应不同的生产环境和需求。

MTI300 的控制程序可以根据实际需求进行定制和修改，从而实现更加灵活的控制策略。

®®注意： 若要深入瞭解 Polycom VVX 300 系列和 VVX 400 系列商務媒體電話，請參閱使用者說明文件（包括功能速查手冊和使用者指南），請至 Polycom Voice Support （語音支援）網站中找到所使用電話的支援頁面，網站位址為：/PolycomService/support/us/support/voice/business_media_phones/包裝內容VVX 300 系列電話選購配件如需詳細資訊，請聯絡經銷商。

VVX 300/301/VVX 400/401/VVX 400系列電話交流電變壓器（因地區而異）VVX 擴充模組（紙卡顯示）VVX 擴充模組（LCD彩色顯示）連接線）連接埠的位置。

鍵）將乙太網路連接到電腦功能連接選購耳機RJ-9 *如需壁掛式安裝，另提供選購配件。

如需詳細資訊，請聯絡經銷商。

連接選用 USB 裝置USB 連接埠CE 認證標誌 R & TTE 指令（僅限歐盟）請聯絡 Polycom 授權經銷商以尋求協助。

安全與法規資訊。

本裝置符合 FCC 規則第 15 項的規定。

操作時必須遵守以下兩個條件：(1) 本裝置不可產生有害的干擾，而且 (2) 本裝置必須能夠承受所接收到的任何干擾，包括承受可能造成不良運作的干擾。

請注意：依照 FCC 規則第 15 項的規定測試證實，此設備符合 Class B 數位裝置之限制。

這些限制的目的是在安裝於居家環境時，針對有害干擾提供合理防護。

此設備會產生、使用並釋出無線電頻率能量，如果未按說明進行安裝與使用，可能會對無線電通訊造成有害干擾。

但我們並不保證特定安裝情況不會產生干擾。

若本設備干擾收音機或電視機訊號，可以開、關本設備電源之方式予以判定。

建議使用者採取以下方式來排除干擾問題：•改變接收天線的方向或位置。

•增加設備與接收器之間的距離。

•本設備接上的插座，最好與接收器接上的插座分屬不同迴路。