WPS(ASME)表格 中英文对照

ASME常常利用辞汇Abrasion, allowance for 磨损，裕量Accessibility，pressure vessels 压力容器可达性Access openings 通道孔Allowance for corrosion, erosion, or abrasion 侵蚀裕量侵蚀或/磨损裕量Applied linings, tightness 应用衬里密封性Approval of new materials, 新材料的批准Articles in Section V 第V卷中的各章Article 1, T-150 第1章T150Article 2 第2章Attachments 附件lugs and fitting 支耳和配件lugs for platforms, ladders, etc. 平台，梯子等的支耳nonpressure parts 非受压件nozzles 接管pipe and nozzle necks to vessel walls 在器壁上的管子和接管颈stiffening rings to shell 壳体上的刚性环Backing strip 垫板Bending stress, welded joints 弯曲应力，焊接接头Bend test 弯曲实验Blind flanges 盲板法兰Bolted flange connections 螺栓法兰连接bolt lands 螺栓载荷bolt stress 螺栓应力design of 关于设计flange moments 法兰力矩flange stresses 法兰应力materials 材料studs 双头螺栓tightness of 紧密性types of attachment 附件类型Bolts 螺栓Braced and stayed surfaces 支持和支撑面Brazed connections for nozzles 接管的钎焊连接Brazed joints, efficiency of 钎焊接头，焊缝系数maximum service temperature 最高利用温度strength of 强度Brazing, cleaning of brazed surfaces 钎焊，钎焊的表面清理fabrication by 用……制造filler metal 填充金属fluxes 钎焊剂heads into shells 封头接入壳体operating temperature 操作温度Buttstraps, curvature 对接盖板，曲率forming ends of 成型端thickness and corrosion allowance 厚度和侵蚀裕量welding ends of 焊接端Carbon in material for welding 焊接用材料中的碳Cast ductile iron vessels, design 可锻铸铁容器，设计pressure-temperature limitations 压力-温度界限service restrictions 利用限制Castings 铸件carbon steel 碳钢defects 缺点impact test 冲击实验inspection 检查quality factor 质量系数specifications 标准Cast iron circular dished heads 铸铁碟形封头Cast iron standard parts, small 铸铁标准部件，小件Cast iron pipe fittings 铸铁管件Cast iron vessels 铸铁容器corners and fillets 圆角和倒角head design 封头设计hydrostatic test 水压实验nozzles and fittings 接管和配件pressure-temperatures limitations 压力-温度界限Certificate of Authorization for Code Symbol Stamp 标准符号标志的认可证书Certification of material 材料证明书Certification of Nondestructive Personnel 无损查验人员证明书Magnetic Particle Examination 磁粉查验Liquid Penetrant Examination液体渗透查验Radiographic Examination 射线超声查验Ultrasonic Examination 超声查验Chip marks on integrally forged vessels 整体锻造容器上的缺口标志Circumferential joints alignment tolerance环向连接，组对公差assembling装配brazing钎焊vessels subjected to external pressure 经受外压的容器Clad material, inserted strips 覆层材料，嵌条examination 检查Clad plate 复合板Cleaning ,of brazed surfaces 钎焊表面清理of welded surfaces 焊接表面Clearance between surfaces to be brazed 钎焊表面间的间隙Combination, of different materials 不同材料组合of methods of fabrication制造方式Computed working pressure from hydrostatic tests 由水实验计算的工作压力Conical heads 锥形封头Conical sections 圆锥截面Connections ,bolted flange (see Bolted flange connections)连接，螺栓法兰（见螺栓法兰连接）brazed 钎焊clamp 卡箍expanded 胀接from vessels to safety valves 由容器至平安阀studded 双头螺栓threaded 螺纹welded 焊接Cooling, after postweld heat treating 冷却，焊后热处置Corrosion allowance 侵蚀裕度Corrosion resistant linings 防侵蚀衬里Corrugated shells 波纹形壳体Corrugating Paper Machinery 波纹板机械Cover plates 盖板on manholes and handholes 在人孔和手孔上的spherically dished 球形封头Cracking, stress corrosion 应力侵蚀裂痕Cutting plates 板材切割Cylindrical shells, supplementary loading 柱状壳体，附加载荷thickness 厚度transition in 过渡段Data report, guide for preparation 预备数据报告的指南Defects in welded vessels, repair 修理焊接容器中的缺点Definitions 概念Design, brazed vessels 设计钎焊容器carbon and low alloy steel vessels 碳钢及低合金钢容器cast ductile iron vessels 可锻铸铁容器cast iron vessels 铸铁容器clad vessels 覆层容器ferritic steel vessels with properutsenhanced by heat treatment 经热处置后提高抗拉性能的铁素体钢容器forged vessels 锻造容器high-alloy steel vessels 高合金钢容器loadings 载荷multichamber vessels 多受压室容器nonferrous vessels 非铁金属容器welded vessels 焊接容器design pressure 设计压力Diameter exemption 直径的宽免Dimensions, checking of 尺寸，校核Discharge of safety valves 平安阀泄放Dished heads (see formed heads) 碟形封头(见成形封头)Disks, rupture 防爆膜Dissimilar weld metal 不同金属的焊接Distortion, of welded vessels 大变形、焊接容器supports to prevent 用支撑幸免Drainage, discharge from safety and relief valves 排放，由平安阀和泄压阀泄放Drop weight tests 落锤实验Eccentricity of shells 壳体的偏心度Edges of plates, metal removal from 由加工板边去除金属tapered 锥度Efficiency, around openings for welded attachments 焊缝系数，围绕焊接附件孔口Elasticity, modulus of 弹性模量Electric resistance welding 电阻焊Ellipsoidal heads 椭圆封头Erosion, allowance for 侵蚀裕量Etching, of sectioned speciments 侵蚀，关于截面试样solutions for examination for materials 查验材料的溶液Evaporators 蒸发器Examination, of sectioned speciments 剖面试样的查验of welded joints 焊接接头的查验Exemptions diameter and volume 直径和容积的宽免Expanded connections 胀接连接External pressure, tube and pipe 外压管External pressure vessels 外压容器allowable working pressure for 许用工作压力charts 算图design of heads for 封头设计joints in shells of 壳体上的接头reinforcement for openings 开孔补强stiffening rings in shells 壳体上的刚性环supports for 支承thickness of shell 壳体厚度reducers 变径段Fabrication, brazed vessels 制造，钎焊容器Ferritic steels vessels with tensile properties enhanced by heat treatment, design经热处置后提高抗拉性能的铁素体钢容器，设计fabrication 制造head design 封头设计heat treatment热处置heat treatment verification tests 热处置验证明验marking 标志materials 材料stamping 标记welded joints 焊接接头Field assembly of vessels 容器的现场安装Filler plugs for trepanned holes 锥孔的管塞Fillet welds 角焊Fired process tubular heaters 直接火管式加热炉Fitting attachments 附件装配Flange connections 法兰连接Flange contact facings 法兰接触面Flanges 法兰bolted design 螺柱法兰设计of formed heads for welding 用于焊接成型封头type of attachment 附件的类型Flat heads and covers, unstayed 无支撑平封头和盖板reinforcement of openings 开孔补强Flat spots on formed heads 成型封头上的平坦部份Flued openings 翻边开孔Forged parts, small 锻造部件，小的Forged vessels 锻造容器heat treatment 热处置localized thin areas 局部薄壁区welding 焊接Forgings 锻件identification of 识别Ultrasonic Examination 超声查验Formmanufacturer’s data report 制造厂数据报告格式partial report 零部件数据报告Formed heads 成型封头flued openings in 封头上翻边开孔insertion of, welded vessels 插入，焊接容器joint efficiency 接头系数knuckle radius 转角半径length of skirt 直边长度on welded vessels 在焊接容器上reinforcement for openings 开孔补强Forming 成型ends of shell plates and buttstraps 壳体板和对接搭板端forged heads 锻造封头shell sections and heads 筒节和封头Furnaces 炉子temperatures for postweld head treatment 焊后热处置温度Furnaces for heat treating 热处置炉temperature control of 炉温操纵Galvanized vessels 镀锌容器Gasket materials 垫片材料Girth joints (see circumferential joints) 环缝接头(见环向接头) Handhole and manhole openings 手孔和人孔开孔Head flange (skirt) length 封头翻边(直边)长度Head joints 封头接头brazing 钎焊welded 焊接Head openings 封头开孔entirely in spherical portion 全数在球体部份Head joints 封头接头concave and convex 凹面和凸面flat (see flat heads) 平板(见平封头)forged 锻造的formed (see Formed heads) 成型的(见成形封头)forming 面型thickness, after forming 厚度，成型以后Heads, design, conical 封头，设计，锥形ellipsoidal 椭圆形hemispherical 半球形spherically dished 球状碟形toriconical 带折边的锥形torispherical 带折边的球形torispherical, knuckle radius 带折边的球形，转角半径Heads and shells 封头和壳体external pressure, out-of-roundness 外压，不圆度openings through or near welded joints 通过或靠近焊缝处的开孔roundness tolerance 不圆度公差Heat exchangers 热互换器Heat treatment 热处置by fabricator 由制造厂进行carbon and low-alloy steel vessels 碳钢和低合金钢容器ferritic steel vessels with tensile properties enhanced by heat treatment 通过热处置后提高抗拉性能的铁素体的容器forged vessels 锻造容器furnaces 炉子high-alloy vessels 高合金容器of test specimens 试样的热处置verification tests of 热处置验证明验Hemispherical heads 半球形封头High pressure vessels 高压封头Holes 小孔for screw stays 用于螺丝固定for trepanning plug sections, refilling 用于穿孔螺塞部份，再填充telltale 指示孔unreinforced, in welded joints 不补强，在焊缝上Hubs, on flanges 高颈，在法兰上Hydrostatic proof tests 水压验证明验destructive 破坏性prior pressure application 在升压之前Hydrostatic test 水压实验cast iron vessels 铸铁容器combined with pneumatic 与气压实验混合的enameled vessels 搪玻璃容器external pressure vessels 外压容器galvanized vessels 镀锌容器standard 标准welded vessels 焊接容器Identification 识别of forging 锻件of plates 平板of welds 焊接Identification markers, radiographs 识别标志，射线照相Impact test 冲击实验certification 证明properties 性能specimens 试样temperature 温度Inspection 检查before assembling 组装之前carbon and low-alloy steel 碳钢和低合金钢cast ductile iron vessels 可锻铸铁容器cast iron vessels 铸铁容器clad vessels 覆层容器during fabrication 在制造期间ferritic steel vessels with tensile properties enhanced by heat treatment 通过热处置后提高抗拉性能的铁素体的容器fitting up 组对forged vessels 锻造容器heat treatment, forgings 热处置，锻件high-alloy steel vessels 高合金钢容器magnetic particle 磁粉material 材料nonferrous vessels 非铁金属容器plate 板材postweld heat treatment 焊后热处置pressure vessels, accessibility 压力容器，可达性quality control 质量治理sectioning of welded joints 焊接接头的剖面查验spot examination 抽样检查steel castings 铸钢件surfaces exposed and component parts 暴露的表面和元件部份test specimens 试样vessels 容器vessels exempted from 免检容器welded vessels 焊接容器Inspection openings 检查孔Inspectors 检查师access to plant 在厂内应有的便利control of stamping 打印治理duties 职责facilities 装备qualification 资格reports 报告Installation 安装pressure-relieving devices 泄压装置pressure vessel 压力容器Integral cast iron dished heads 整体铸铁碟形封头integrally finned tubes 整体翅片管Internal structures 内部构件Jacketed vessels 夹套容器Joints 接头brazed 钎焊circumferential (see Circumferential joints) efficiency, brazed 环缝(见环向接头)系数，钎焊welded 焊接electric resistance, butt welding 电阻，对接焊in cladding and applied linings 在覆层及衬里in vessels subjected to external pressure 在经受外压的容器lap (see Lap joints) 搭接(见搭接接头)longitudinal (see Longitudinal joints) 纵向(见纵向接头) tube-to-tubesheet 管子对管板Jurisdictional Review 权限审查Knuckles 过渡圆角radius 半径transition section 变径段Lap joints 搭接接头amount of overlap 搭接量brazed 钎焊longitudinal under external pressure 在外压作用下纵向的welded 焊接Laws Covering Pressure Vessels 涉及压力容器的法规Lethal gases or liquids 致命的气体或液体Ligaments, efficiency of 孔带，系数Limitation on welded vessels 焊接容器的限制Limit of out-of-roundness of shells 壳体不圆度的限制Linings 衬里corrosion resistant 抗侵蚀Liquid penetrant examination 液体渗透查验Loadings 载荷Local postweld heat treatment 局部焊后热处置Longitudinal joints 纵向接头alignment tolerance 对准公差brazing 钎焊vessels subjected to external pressure 经受外压的容器Low-temperature operation 低温操作Low-temperature vessels brazed 低温容器，钎焊for gases and liquids 用于气体和液体impact test requirements 冲击实验要求impact test, when not required 冲击实验，当不要求时marking 标志materials 材料testing of materials 材料实验Lugs for ladders, platforms, and other 梯子，平台及其它附件的支耳Magnetic particle inspection 磁粉检查Manholes, and handholes 人孔，手孔cover plate for 盖板minimum vessel diameter requiring 所需最小容器直径Manufacture, responsibility of 制造者，职责Manufacturer’s Data Report (see Data Report) 制造厂数据报告(见数据报告) Manufacturer’s stamps 制造厂的印记Marking castings 标志，铸件materials 材料plates 板材standard pressure parts 标志受压件valves and fittings 阀门和配件with Code symbol 带有标准符号Markings, transfer after cutting plates 标志，板材切割以后的转移Materials, approval of new 材料，新材料的批准approval of repairs 修补的批准brazed vessels 钎焊容器carbon and low-alloy steel vessels 碳钢和低合金钢容器cast ductile iron 可锻铸铁castings 铸铁cast iron vessels 铸铁容器certification 合格证clad vessels 覆层容器combination of 组合材料ferritic steel vessels with tensile properties enhanced by heat treatment 经热处置后提高抗拉性能的铁素体钢容器forged vessels 锻造容器for nonpressure parts 非受压元件heat treatment of 热处置high-alloy steel vessels 高合金钢容器inspection of 检查nonferrous vessels 非铁金属容器pipe and tube 管子plate 板rods and bars 杆和棒specification for 标准standard pressure, parts 标准受压元件unidentified 未分辨的use of over thickness listed in Section Ⅱ采纳超过列于第Ⅱ卷表中的厚度welded vessels 焊接容器Measurement, 测量dimensional 尺寸of out-of-roundness of shells 壳体不圆度Metal temperature determination 金属温度，确信control of 操纵Mill undertolerance 钢厂负公差操纵Minimum thickness of plate 板材的最小厚度操纵Miscellaneous pressure parts 其它受压件操纵Multichamber vessels design 多承压室容器，设计Multiple duplicate vessels 多个相同的容器Multiple safety valves 多个平安阀Nameplates 铭牌New materials 新材料Noncircular vessels 非圆形容器ligament efficiency 孔带系数nomenclature 术语obround design 长圆形设计rectangular design 矩形设计reinforcement 补强examples 实例Nonpressure parts, attachment of 非受压元件的连接Notch ductility test 缺口韧性实验Nozzle openings, reinforced 接管开孔，补强的unreinforced 非补强的vessels subjected to external pressure 经受外压得容器Nozzles attachment of to shell 接管，与壳体的连接minimum thickness of neck 缩颈的最小厚度(see also Connections)(也可见连接件)Nuts and washers 螺母和垫圈Offset of edges of plates at joints 在接头处板边的误差Openings adjacent to welds 开孔，临近焊缝closure of 封锁for connections to brazed vessels 用于对钎焊容器的连接for drainage 用于排放head (see Openings head and shell) 封头(见开孔，封头和壳体) in flat heads 在平板封头上inspection 检查manhole (see Manholes) 人孔(见人孔)nozzle (see Nozzle opening) 接管(见接管开孔)shell (see Openings, head and shell) 壳体(见开孔，封头和壳体) through welded joints 通过焊接接头Openings, head and shell, computation of 开孔，封头和壳体，计算not requiring additional reinforcement 不需要附加补强reinforced, size 补强，尺寸reinforcement for adjacent openings 临近开孔的补强reinforcement of 补强requiring additional reinforcement 需要附加补强shapes permissible 许用形式unreinforced, size 不补强的，尺寸Outlets, discharge, pressure relieving devices 排放口，出料，泄压装置Out-of-roundness 不圆度Overpressure limit for vessels 容器的超压极限Partial data report, manufacturer’s 零部件数据报告，制造厂的Parts, miscellaneous 部件，各类各样的Peening 捶击Pipe connections openings for 管子的连接，用于开孔Pipe fittings vessels built of 管子配件，制造的容器Pipe and tubes 各类管子Pipe used for shells 用作壳体的管子piping external to vessel 容器外的管子Plate, curvature 板，曲率measurement, dimensional check 测量，尺寸校核Plate edges cutting 板边，切割exposed left unwelded 留下不予焊接的显露部份inspection of 检查Plates 平板alignment 找准cover 盖板cutting 切割forming 成型heat treatment 热处置identification 标志impact test 冲击实验inspection 检查laying out 划线less than 6 mm thickness 厚度小6mmmarkings transfer after cutting 标志，在切割以后的转移minimum thickness 最小厚度repair of defects 缺点修理specifications 标准structural carbon steel 结构碳钢Plug welds 塞焊Pneumatic test 气压实验pressure 压力yielding 屈服Porosity welded joints 气孔，焊接接头Porosity charts 气孔图Postheat treatment 后热处置connections for nozzles and attachments 用于接管和附件的连接cooling after 随后的冷却furnace temperature 炉温inspection 检查local 局部requirements 要求temperature range 温度范围welded vessels 焊接容器Preheating 预热Preparation of plates for welding 焊接板材的预备pressure, design 压力，设计limits 极限(see also Working pressure, allowable) (也可见工作压力，许用)Pressure parts miscellaneous 受压件，其它的Pressure relieving devices 泄压装置discharge 排放installation and operation 安装和运转rupture disks 防爆模setting 整定Pressure vessels 压力容器exempted from inspection 免检Produce form of Specification 产品技术条件Proof test hydrostatic (see Hydrostatic proof test) 验证明验，水压(见水压实验) Qualification 评定of brazers 钎焊工of welders 焊工of welding procedure 焊接工艺Quality Control System 质量保证体系Quenching and tempering 淬火及回火Quick-actuating closures 快开盖Radiograph factor 射线照相系数Radiographing 射线照相examination by 检查partial 部份quality factors 质量系数requirements 要求spot examination 抽样检查retests 从头实验thickness, mandatory minimum 规定最小厚度Radiographs, acceptance by inspector 射线照相，由检查员以为合格gamma rays, radium capsule γ射线，装镭的盒子interpretation by standard procedure 由标准程序的说明rounded indications 圆形显示Reaming holes for screw stays 为固定螺钉用的铰孔Reducer sections, rules for 变径段，规程Reinforcement 补强defined limits 规定的范围head and shell openings 封头及壳体开孔large openings 大开孔multiple openings 多个开孔nozzle openings 接管开孔of openings in shells, computation of 壳体上开孔，计算openings subject to rapid pressure fluctuation 经受压力突然波动的开孔Fluctuation 经受压力突然波动的开孔strength 强度Relief devices 泄放装置(see also Pressure relieving devices, Safety and relief Valves)(也可见泄压装置，平安阀和泄压阀) Relieving capacity of safety valves 平安阀排量Repairs, approval of defects in material 修理，材料中缺点的认可defective Brazing 有缺点的钎焊defects in forgings 锻件中的缺点defects in welds 焊缝中的缺点Responsibility of manufacturer 制造者的职责Retention of Records 记录的保留Radiographs 射线照相Manufacturer’s Data Reports 制造厂的数据报告Retests, frogings 复试，锻件impact specimens 冲击试样joints, welded 接头，焊接Rods, bars, and shapes 杆棒喝型材Rolled parts, small 轧制件，小件Rupture disks 爆破模Safety 平安性safety relief, and pressures relief valves, adjustable blow down, capacity certification 平安泄放和泄压阀，可调剂的泄放，排放量证明capacity, conversion 排量，换算connection to vessels 连接至容器construction 结构discharge pipe 排放管indirect operation 间接操作installation 安装installation on vessels in service 容器在役时的安装liquid relief 液体泄放marking 标志minimum requirements 最低要求pressure setting 压力整定spring loaded 受载弹簧springs, adjustment 弹簧，调剂stop valves adjacent to 临近的截止阀test 实验protective devices 防护装置for unfired steam boiler 对非直接火蒸气锅炉Scope 适用范围sectioning, closing holes left by 解剖，解剖孔的封锁etching plugs taken 解剖样的侵蚀examination by 检查Service restriction 利用限制Shapes, special 形状，特殊Shell plates, forming ends of 壳体用材料，封头成型Shells 壳体allowable working pressure 许用工作压力computation of openings in 开孔计算forming 成型made from pipe 由管子制造的stiffening rings 刚性环thickness 厚度Transition section 过渡段Sigma-phase formation σ相的形成Skirts length on heads 直边、封头上的长度support of vessels 裙座，容器支撑Slag inclusion welds 焊缝中的夹渣Special constructions 特殊结构Specification for materials 材料标准Spherical sections of vessels 容器的球形部份Spot examination of welded joints 焊接接头的抽样检查Springs for safety valves 平安阀的弹簧Stamping location of 打印位置multipressure vessels 多重压力容器omission of 省略safety valves 平安阀with Code symbol 带有标准标记Stamps, certificate of authorization 钢印，授权low stress 低压力not to be covered 不该覆盖to be visible on plates 在板上可见Static head, in setting safety valves, effect of on limiting stresses 静压头，在整定平安阀时，阻碍，对极限应力Stayed surfaces 支撑表面Staying formed heads 成型封头的支撑Stays and staybolts, adjacent to edges of staybolted surface 支撑件及拉撑螺栓，临近用螺栓拉撑得表面周边处allowable stress 许用应力area supported 支撑面dimensions 尺寸ends 端部location 位置pitch 节距screw, holes for 螺孔upset for threading 为车制螺纹的镦粗welded 焊接的Steam generating vessels, unfired 蒸汽锅炉，非直接火Steel, carbon content 钢，含碳量Stenciling plates for identification 在板材上打印标志Stiffening rings, attachment to shell 刚性环，和壳体的装配for vessels under external pressure 用于外压容器Stiffness, support of large vessels for 刚性，大容器支座Stop valves 截止阀adjacent to safety and relief valves 临近于平安和泄压阀Strength of brazed joints 钎焊接头的强度Stress corrosion cracking 应力侵蚀裂痕Stress values, attachment weld 应力值，连接焊缝basis for establishing 确信的基础carbon and low-alloy steel 碳钢和低合金钢cast iron 铸铁ferritic steels with tensile properties enhanced by heat treatment 经热处置后提高抗拉性能的铁素体刚high-alloy steel高合金钢nonferrous metals 非铁金属Stud bolt threads 双头螺栓螺纹Studded connections 双头螺纹连接Supplementary design formulas 补充设计公式Supports, design 支座，设计pressure vessels 压力容器temperature free movement under 在温度下活动不受约束types of steel permissible for 许诺的钢材类型vessels subjected to external pressure 经受外压的容器Surface Weld Metal Buildup 金属堆焊表面Tables, effective gasket width b 表，有效垫片宽度bgasket materials and contact facings 垫片材料和接触面maximum allowable efficiencies for arc and gas welded joints 电弧焊和气焊接头的最大许用系数minimum number of pipe threads for connections 管螺纹连接的最少螺纹牙数molecular weights of gases and vapors 气体和蒸汽的分子量of stress values, carbon and low-alloy steel 应力值，碳钢和低合金钢cast iron 铸铁cast ductile iron 可锻铸铁ferritic steels with tensile properties enhanced by heat treatment经热处置后提高抗拉性能的铁素体钢high-alloy steel 高合金钢nonferrous metals 非铁金属welded carbon low-alloy pipe and tubes 焊接低合金碳钢管of values factor Ｋ系数Ｋ值factor M 系数Ｍfactor 系数postweld heat treatment requirements 焊后热处置要求recommended temperature ranges for heat treatment 推荐的热处置温度范围spherical radius factor K1球半径系数K1Telltale holes 指示孔in opening reinforcement 开孔补强Temperature, definitions 温度，概念design 设计determination 确信free movement of vessel on supports 支座上的容器活动不受约束heat treatment 热处置limitations, of brazed vessels 限制，钎焊容器of cast ductile iron 可锻铸铁of postweld heat treating 焊后热处置metal, control of 金属，操纵operating or working, definitions 操作或工作，概念zones of different 不同区域Termination point of a vessel 容器的界限点Test coupons 试样Test gages requirements 实验仪表，要求Test plates heat treatment 试板，热处置impact test 冲击实验production 生产Tests, hydrostatic proof 实验，水压验证pneumatic (see pneumatic test) 气压，见气压实验vessels whose strength cannot be calculated 不能由计算求得强度的容器calculated 不能由计算求得强度的容器Thermal buffers 热缓冲器Thermocouples attachment 热电偶，安装Thickness gages, details 厚气宇规，细节Thick shells, cylindrical 厚壳体，圆柱形spherical 球形Thin plates marking 薄板，标志Threaded connection 螺纹连接Threaded inspection openings 螺纹检查孔Threads, stud bolts 螺纹，双头螺栓Tolerances, forged shells and heads 公差，锻造容器及封头Toriconical heads 带折边的锥形封头Torispherical heads 带折边的球形封头Transfering marking on plates 板上标志的移植Transition in cylindrical shells 柱状壳体的过渡Trays and baffles, acting as partial shell stiffeners 塔盘及挡板，作为部份壳体增强圈Tubes and pipe 管子Tube-to-tubesheet joints 管子与管板的连接Ultrasonic examination of welds 焊缝的超声查验UM vessels UM 容器Unfired steam boiler 非直接火蒸汽锅炉Unidentified materials 未识别的材料Valves, connections 阀，连接safety and relief (see safety and relief valves) 平安和泄压装置Valves and fittings, marking 阀及其配件，标志Verification tests, heat treatment 验证明验，热处置Volume exemption 容器的免检Weld deposits, cleaning 焊接熔敷金属，清理peening 捶击Welded joints, category 焊接接头，类别description of types 类型的描述efficiency 焊缝系数impact test, across 冲击实验，横向postweld heat treating 焊后热处置radiographic examination, complete 射线照相检查，整个的rounded indications 圆形显示sectioning, etch test 解剖，侵蚀实验spot examination 抽样检查staggered, longitudinal 错开，轴向taper, plates of unequal thicknesses 锥度，不等厚板types around openings 类型，围绕开孔ultrasonic examination of 超声查验Welded reinforcement of nozzle openings 接管开孔的焊缝补强Welded vessels 焊接容器holes in joints of 接头处的孔inspection 检查limitations on 限制tests of 实验Welders and welding operators 焊工和自动焊工identifying stamps 识别标记records of, by manufacturers 由制造厂所作的记录test of qualification 评定实验Welding 焊接cleaning of welded surfaces 焊件表面清理details, limitations 细节，限制forged vessels 锻造容器materials 材料materials having different coefficients of expansion 膨胀系数不同的材料of attachment around openings 开孔周围的连接plate, fitting up joints 平板，连接处的装配plate edges, matching 板边，匹配preparation of plates 钣材的制备procedure qualification 工艺评定processes 工艺test requirement 实验要求Weld metal, composition 焊缝金属，成份Welds acceptability, when radiographed 焊缝合格，用射线照相时when sectioned 解剖时fillet 填角identification of 识别plug 塞焊reinforcement, butt welds 补强，对接焊repairs of defects in 焊缝中缺点的修补sharp angles, avoid at weld edges 尖角，幸免在焊缝边上structural 结构tack 定位焊types, description 类型，描述ultrasonic examination of 超声查验Working pressure allowable, braced and stayed surfaces 许用工作压力，有拉撑和支撑表面by proof test 验证性实验definition of 概念。

QW-482Company Name China Tianchen Engineering Corporation (TCC) ByWelding Procedure Specification No. DateRevision No. DateWelding Process(es) SMAW Type(s) Manual(Automatic,Manual,Machine,or Semi-Automatic)JIONTS (QW-42) DetailJoint Design V-GrooveRoot Spacing 2mmBacking: Yes No NoBacking Material (Type)□Metal □Nonfusing Metal□Nonmetallic □OtherBASE METALS (QW-403)P-No. I Group No. 1 to P-No. I Group No. 1 ORSpecification and type/grade or UNS Numberto Specification and type/grade or UNS NumberORChem. Analysis and Mech. Prop.to Chem. Analysis and Mech. Prop.Thickness Range:Base Metal: Groove 4~12mm Fillet No LimitMaximum Pass Thickness ≤1 /2 in. (13 mm) (Yes) yes (No)OtherFILLER METALS (QW-404) 1 2 Spec. No. (SFA)AWS No. (Class) AWS A5.1F-No.A-No.Size of Filler MetalsFiller Metal Product Form Ф3.2 - Ф4.0mmSupplemental Filler MetalWeld Metal Thickness Range:GrooveFilletElectrode-Flux (Class)Flux TypeFlux Trade NameConsumable InsertOther*Each base metal-filler metal combination should be recorded individually.QW-482 (Back)WPS No. Rev.POSITIONS (QW-405)Position(s) of Groove 4G Welding Progression: Up √Down Position(s) of Fillet 4G Other POSTWELD HEAT TREATMENT (QW-407) Temperature Range —Time Range —Other —PREHEAT (QW-406)Preheat Temperature, Minimum —Interpass Temperature, Maximim —Preheat Maintenance —Other GAS (QW-408)Percent CompositionGas(es) (Mixture) Flow RateShieldingTrailingBackingOtherELECTRICAL CHARACTERISTICS (QW-409)Weld Pass(es) ProcessFiller MetalCurrentType andPolarityAmps(Range)(A)WireFeedSpeedEnergy orPower(J/mm)Volts(V)TravelSpeed(mm/min)Other Classification DiameterRoot Filler Cap SMAWSMAWSMAWA5.1 E7018A5.1 E7018A5.1 E70183.2mm3.2/4.0mm3.2/4.0mmDC (+)DC (+)DC (+)90-130120-190120-1801900-20001970-25902000-259018-2618-2618-2650-10050-15050-140Pulsing Current Heat Input (max.)Tungsten Electrode Size and TypeMode of Metal Transfer for GMAW (FCAW)OtherTECHNIQUE (QW-410)String or Weave BeadOrifice, Nozzle, or Gas Cup SizeInitial and Interpass Cleaning (Brushing, Grinding, etc.) Glassing Machine or Wire BrushMethod of Back Gouging Scarfing or Glassing MachineOscillation SwingContact Tube to Work DistanceMultiple or Single Pass (Per Side) SingleMultiple or Single ElectrodesElectrode SpacingPeeningOther。

焊接工艺规程（WPS ）Page 1 of 2单位名称：WPS No.日期：所依据的PQR No.修改号No.日期：焊接方法：SMAW机械化程度：（手工、半自动、自动）接头（QW-402 ）接头型式：对接简图：（接头形式、坡口形式与尺寸、焊层、焊道布置及顺序）根部间隙：V 型衬垫：有无衬垫材料（型式）（有关二面的和金属成型块）其他：□金属□不熔金属□非金属□其它材料母材（QW-403 ）P-No.Group No.钢号和等级UNS No 为：化学成份和力学性能为：与 P-No.Group No.与钢号和等级UNS No 为：与化学成份和力学性能为：相焊或相焊或相焊厚度范围：母材：坡口焊缝最大焊道厚度≤1/2in.(13mm)角焊缝是：否：其他填充金属（ QW-404 ）SFA No.：AWS No. ：F— No. ：A — No.：填充金属尺寸：填充金属产品形式附加填充金属：评定的焊缝金属厚度范围：坡口焊：角焊缝：焊丝—焊剂（分类号）：焊剂类型焊剂商品类型可熔化嵌条：其他：每种母材和填充金属的给合宜分别记录。

WPS No. 修改号 Page 2 of 2焊接位置（ QW-405 ）坡口焊缝位置： 平焊焊接方向：向上 向下角焊缝位置： 其它：预热（ QW-406 ）最低预热温度： / 最高层间温度 / 预热保持方式： /其它：/（当应用连续或特殊的加热时，宜予记录）焊后热处理（ QW-407 ）温度范围（℃） /时间范围（ h ） /其它：气体（ QW-408 ）（百分比组成）气体混合比流量（L/min ）保护气：///尾部保护气： / / /背面保护气： ///其它：电特性（ QW-409 ）填充金属电流类送丝速焊接焊接方度能量或电压安培 速度焊道型和极(cm/min功率其它法牌号直径（A ）(cm/ （ V ）性)(kj/cm)min)安培、电压和功率或能量范围宜按每种焊条（焊丝）尺寸、位置和厚度等分别记录。

WELDING PROCEDURE SPECIFICATIONS (WPS)焊接工艺规程WPS NO. _______________ Rev. No. _________________ Page ofBy 签字人DateSupporting PQR No.(s) 日期 对应的工艺评定编号Date__________ 日期 _______________________ Welding Process(es) Type(s) 焊接方法 ____________________________ 自动化等级 ______________________________________________________________(Automatic, Manual, Machine, or Semi-Automatic) (自动、手工、机动或半自动)Company Name公司名称 WPS No.焊接工艺规程编号Rev. No.修改号*Each base metal-filler metal combination should be recorded individually.WELDING PROCEDURE SPECIFICATIONS (WPS)焊接工艺规程WPS NO. _________________ Rev. No. ___________________ Page ofPulsing Current 脉冲电流Heat Input ( Max.)热输入(最大)Tungsten Electrode Size and Type ( Pure Tungsten,2Thoriated etc.)钨极尺寸和型号(纯钨,2%钍钨极等) Mode of Metal Transfer for GTAW (FCAW) ( Spray Arc, Short Circuiting Arc, et 熔滴过渡型式(射流或短路)Electrode Wire Feed Speed Rang 送丝速度范围 ______________________________________________________________________________________Other 其它TECHNIQUE 焊接技术(QW-410)Stri ng or Weave Bead 直进焊或摆动焊 ______________________________________________________________________________________ Orifice or Gas Cup Size 嘴孔或喷嘴尺寸 mmInitial and Interpass Cleaning打底焊道和中间焊道的清理方法(Brushing, Grinding, etc.)( 刷理或打磨等等) ______________________Method of Back Gouging背面清根方法Oscillati on 横摆方法 ________________________________________________________________________________________________________ Con tact Tube to Work Dista nee 导电嘴至工件距离 ____________________________________________________________________________ Multiple or Single Pass 多道焊或单道焊 (Per Side)( 每侧) _________________________________________________________________ Multiple or Single Electrodes 多丝焊或单丝焊Travel Speed 焊接速度(Range)(范围) _________________________________________________________________________________Peening 锤击Use of thermal processes 使用热工艺 _______________________________________________________________________________________ Other 其它对于每一母材-填充金属的组合均需分别填表Date 日期。

缩写词部分AB--Anchor Bolt地脚螺栓Earthing boss接地板Abs--Absolute绝对的Abs--Abstract文摘、摘要A/C--Account帐、帐目AC--Alternating Current交流电Add--Addendum补充、补遗、附录ADL--Acceptable Defect Level允许的缺陷标准Adpt--Adapter连接器、接头AE--Absolute Error绝对误差AET--Acoustic Emission Examination声发射检验AISC--American Institute of Steel Construction美国钢结构学会AISI--American Iron and Steel Institute美国钢铁学会AL--Aluminium铝Alk--Alkaline碱的、强碱的ALM--Alarm报警Alt--Alternate交流、改变Amb--Ambient周围的Amt--Amount数量、金额Anh--Anhydrous无水的ANSI--American National Standard Institute美国国家标准学会API--American Petroleum Institute美国石油学会App--Apparatus设备App--Appendix附录、补遗Appl--Applied应用的Appl--Applicable适当的、合适的Approx--Approximate大约、近似Arrgt--Arrangement布置AS--Alloy steel合金钢Asb--Asbestos石棉ASL--Above Sea Level海拔高度ASM--American Society for Metals美国金属学会ASME--American Society of Mechanical Engineers 美国机械工程师学会Assem--Assembly装配ASTM--American Society for Testing and Materials 美国材料试验学会Atm--Atmosphere大气atm--Atmosphere pressure大气压Auto--Automatic自动Aux--Auxiliary辅助设备、辅助的Avail--Available有效的、可用的Avg--Average平均AW--Arc welding电弧焊AW--Automatic Welding自动焊A.W.G.--American Wire Gauge美国线规AWS(AWI)--American Welding Society(Institute)美国焊接学会BAB--Babbitt Metal巴氏合金Baf--Baffle折流板、缓冲板BB--Ball Bearing滚珠轴承BC--Between Centers中心距、轴间距BC--Bolt circle螺栓中心圆BD--Blow down放空、放料BEDD--Basic engineering design data基础工程设计数据Bet--Between在…之间Bev--Bevel斜角、坡口BF--Back face背面、反面BF--Blind flange法兰盖（盲法兰）BHN--Brinell hardness number布氏硬度值BL--Battery Limit界区BL--Battery Line界区线B/L--Bill of Loading载荷数据表Bld--Blind盲板Blk--Black黑色Blk--Blank空白BM--Bench Mark基准标志BM--Bending Moment弯矩B/M(BOM)--Bill of Material材料表Bot--Bottom底BP--Back Pressure背压BP--Base plate底板BR--Basic Requirements基本要求BRG--Bearing轴承BRKT--Bracket支架Brs--Brass黄铜BS--Both Side两边BS--British Standard英国标准BS--Balance Sheet平衡表Bskt--Basket筐BTU--British Thermal Unit英国热量单位BV--Back View后视图BV--Butterfly Valve碟阀BW--Brine Vater冷冻盐水BW--Butt Welding对焊BWG--Birmingham Wire Gauge伯明翰线规BWRA.--British Welding Research Association英国焊接研究协会C--Centigrade(degree)摄氏度数CA--Chemical Analysis化学分析CA--Corrosion Allowance腐蚀裕量Calc--Calculate计算Cap--Capacity能力、容量CAS--Cast Alloy Steel铸造合金钢Cat--Catalyst触媒、催化剂Catg--Catalog目录、样本C-C(C/C)--Center to center中心距cc--carbon copy复写（纸复制）本cc--cubic centimeter立方厘米CCW--Counter clockwise反时针方向CD--Cold Drawn冷拉的、冷拔的CE--Covered Electrode焊条Cent--Centrifugal离心的CF--Centrifugal Force离心力CFW--Continuous Fillet Weld连续角焊缝CG--Center of Gravity重心CH--Case-Hardening表面硬化Ch--Chapter章节Cham--Chamfer倒角、斜角、斜面Chan--Channel通道、沟槽、管箱、槽钢Chk--Check检查CI--Cast Iron铸铁CIF Cost，Insurance and Freight到岸价格Circ--Circumference圆周、环向CL--Class等级、类别CL--Center Line中心线CL--Clearance间隙CLAS--Cast Low Alloy Steel低合金铸钢CM--Center of Mass质量中心Cnds--Condensate冷凝液CO--Clean Out清除Co--Company公司Coef--Coefficient系数Col--Column柱、塔Comb--Combination组合Comp--Compare比较Comp--Compound化合物、复合的Compn--Composition组分Conc--Concrete混凝土Conc--Concentration浓度Cond--Conductor导体Cond--Condition条件Conn--Connection联接、接口Const--Constant常数、恒定的Const--Construction结构，建造Cont--Control控制Cont--Contain包含Cont--Content内容、含量Corp--Corporation公司Corr--Corrosion腐蚀CP--Centipoise厘泊CP--Center of Pressure压力中心Cpl--Coupling管箍Cplg--Coupling联轴节CR--Chloroprene Rubber氯丁橡胶CS--Carbon Steel碳钢CS--Center Section中心截面CSTG--Casting铸造、铸件Ctr--Center中心CW--Cooling Water冷却水CW--Continuous Welding连续焊Cy--Cycle循环Cyl--Cylinder气缸、圆筒正文部分1WN带颈对焊法兰SO带颈平焊法兰IF整体法兰WN大直径管法兰BL法兰盖LF/SE对焊环松套法兰SW承插焊法兰（HG20616-20623）带颈对焊法兰（WN）密封面形式：突面（RF）凹面（MF）凸面（M）全平面（FF）欍槽面（TG）Header管箱Supporting column支柱Phenum风箱Fan ring风筒Fan deck风机底板Drive assembly驱动组件Forced draught鼓风式/induced draught引风式One-bay单排架Two-bay双排架Sheave皮带轮Item成台设备Plug sheet丝堵板Top plate顶板bottom plate底板--end plate端板--removable cover plate可卸盖板Stay plate加强板Side fame侧面框架tube spacer定距管Tube support cross-member管子支撑梁Tube keeper管子支撑件Instrument connection仪表接头Stud construction,confined gasket榫槽结构窄垫片Flanged construction,confined gasket凹凸结构窄垫片Full-faced gasket全表面宽垫片Plug header丝堵式管箱Stiffener加强件Front正面Side侧面Box-type plenum箱型风箱Transition plenum转换风箱Standard fit标准配合Undertolerance负偏差Overtolerance正偏差Special close fit特殊紧配合Tube-hole grooving管孔槽Thread lubrication罗纹润滑Centerline header管箱中心线Centerline nozzle接管中心线Reference line基准线Out-of-plane tolerance不平度公差Holding-down bolts夹紧螺栓The instrument air supply空气供给仪器The louvre characteristic performance curve百叶窗特性曲线Instrumentation仪表Dry-bulb temperature干球温度Max.exposure temp.of elastomeric material弹性材料的最大外露温度For pheumatic positioner气动定位器For pheumatic diaphragm actuators气动隔膜执行机构For rotary unions旋转单元Expanded metal fan guard mesh风机护罩多孔金属网Direct right-angle gear drive齿轮直角直接驱动Belt drive皮带驱动Direct motor drive电动机直接驱动Fan support风机支架Suspended belt drive,motor shaft down悬挂皮带驱动，电动机轴朝下Gear box齿轮箱Bearing轴承Coupling联轴器Base plate底板Louvre deflection窗叶挠度Louvre blades in closed position with design load of 2000N/m2设计载荷为2000N/m2的处于关闭状态的窗叶Louvre side frames with uniform design load of 2000N/m2均匀设计载荷为2000的百叶窗边缘框架Length of the span between points of support俩支撑点之间的跨度Platform平台Column支柱Walkway走道Live load动载荷Floor framing平台铺板Columns and brackests支柱及托架Ladders and stairways梯子和脚踏Fan thrust风机推力(internal)refractory linings耐火衬里Wet gas compressor trim coolers湿气压缩机调温冷却器Stripper condenser汽提塔冷凝器Flattening椭圆度Stripper feed pre-heater汽提塔进料预热器Stripprt1st reboiler汽提塔第一再沸器Primary absorber bottom pumparound cooler一级吸收塔底循环泵冷却器Low temp.HIC resist KCS低温抗HIC镇静钢Gasoline trim cooler汽油调温冷却器Lean oil trim cooler贫油调温冷却器Fuel gas cooler燃料气冷却器Debutanizer reboiler脱丁烷塔冷凝器Butane product cooler丁烷产品冷却器Propane/propylene rectifier condensers丙烷/丙烯精馏塔冷凝器Mixed C3cooler混合C3冷却器Residue MPS heater渣油MPS加热器Feed/slurry pumparound exchanger进料/油浆循环泵换热器Slurry HP steam generator油浆-高压蒸汽发生器Clarified oil MP steam generator澄清油中压蒸汽发生器Safetyrelated technical manual产品安全技术说明书Namely即Specific gravity比重Fixed tubesheet heat exchanger固定管板式换热器Floating head type heat exchanger浮头式换热器U-tube type heat exchanger U形管式换热器Kettle type heat exchanger釜式换热器Double tube type heat exchanger套管式换热器Slip tubesheet heat exchanger with stuffing box滑动管板填料函换热器Stuffing box heat exchanger填料函式换热器Double sheet heat exchanger双管板换热器Thin tubesheet heat exchanger薄管板换热器Bayonet type heat exchanger插管式换热器Jacket type heat exchanger夹套式换热器Mesh demister丝网除沫器Skirt shell裙座筒体Cover plate盖板Base plate底板Straddle equi-spaced跨中均布Bottom head下封头Weld symbol std.焊缝符号标准Weld forms for NZLS-SHELL--C、D类焊缝坡口形式Earthquake deg.地震烈度“Duplicate”=“复制”“for gas service only”=“仅用于气体工况”0.8mm radius round半径为0.8mm的圆1st sulphur condenser第一硫冷凝器正文部分2A0.8mm radius round tool（磨平用）A balancing bellows平衡波纹管A blank head毛坯封头A centre line elevation of3.5m at the top exchanger 顶层换热器中心线拔高A certificate of conformance性能证书A certified test report合格的试验报告A chord length弦长arc length弧长A circumferential line环向线A coded marking编号标志方法A coefficient of discharge排放系数A computed radial shear计算所得的径向剪切载荷A cone with a knuckle radius有转角半径的锥壳A cone-to-cylinder junction锥壳与圆筒的接逢A definitely determinable yield point有明显屈服点的材料A dimensioned detail sketch of defect location and extent缺陷位置和范围的尺寸草图A fillet weld with a min.throat dimension角焊缝最小厚度a fine grain practice细化晶粒处理A fixed geographical location固定地理位置A flare radius扩口半径A forged welding neck flange锻制焊接带颈法兰A given nominal chemical analysis给定的公称化学成分A heated electrode holder已加热电焊条的焊条筒A mockup模拟产品a needle gun for scale清除剥落层的撞针枪A neutral to slightly reducing flame中性至微还原性火焰A non-welded dished head非焊接凸形封头A pad垫板A positive mechanical locking arrangement可靠的机械锁紧装置A proven quantitative analytical technique有效的定量分析方法A ratio of min.specified yield曲强比A ratio of not less than three to one不小于3：1的比例A recess1/16in.deep开凹型座A reverse curve section反向曲线段A rupture disk holder安全膜夹持器A shallow contaminated area一个浅的污染区A shielding gas is employed采用保护气体transfer mode熔滴过渡形式short-circurting非短路过渡A stayed jacket具有拉撑件的夹套A stiff and lump paste粘稠而多块状物的糊A straight thread直螺纹A substantial lifting device靠可靠的提升装置A suitable gas leak test适当的气密性试验A telebrinell portable tester便携式布氏测定仪A threaded fastener with a head on one end一端有螺栓头的螺纹紧固件A three to one taper over…在…上形成3：1的泄面A transition section reducer变径过渡段壳体A transition with a slope not exceeding3:1过渡段其坡度不超过3：1A try cock试验旋塞A uniform force fit with the mating section at the root of the weld----在焊根部位的配合处应均匀贴合A valve data tag阀门数据标签A wet paint surface涂漆的未干的表面A wire penetrameter线型透度计Abnormal pressure caused by deflagration由爆燃引起的异常Above3o’clock/9o’clock position高于时钟3点/9点的位置Abrasive tooling打磨工具Abrupt transition突变过渡Accelerated cooling快速冷却Acceptance by inspector由检验员认为合格Acceptance criteria验收标准Acceptance standard合格标准Access openings通道孔Accessibility of pressure vessels压力容器可达性Accumulation of pressure压力累积Acid etch酸蚀Across,impact test横向冲击试验Acting as partial shell stiffeners做为部分壳体加强圈Actual heat treating temperature实际热处理温度Actual prevailing climatic conditions实际的气候条件Additional reinforcement附加补强Adjacent sliding surface such as guides and disks or disk holders相接触的滑动表面，如导向套、阀瓣、或阀瓣夹持器Adjacent to edges of stay-bolted surface临近用螺栓拉撑的表面周边处Adjoining base material相临母材Adjusting slider调整板Admissible wall thickness最小许可壁厚Aerosol can喷罐Affixed to安装到…After Finning在和翅片成一体后Agitator device搅拌装置Air baffle(upper/lower)挡风板Air hardening steels自淬钢Air pocket气袋Air volume风量Alignment tolerance对准公差,组对公差All hydro-test leakage液压试验发现的所有泄露点Allow.Press.Drop允许压降Allowance for corrosion,erosion,abrasion腐蚀裕量，侵蚀，磨损裕量Alternative design for替代Ambient temperature环境温度Amine lean solution/rich贫/富胺液Ammonia氨Amount of overlap搭接量An adjustable blow-down construction可调排污结构An aluminum coating on the hot face(gas side)热管板的热面（气体侧）喷一层铝thermally sprayed aluminum热喷铝An angle joint connecting锐角对接焊连接angle joint 斜口接头An atmospheric dew point常压露点温度An individual tube hydrostatic test逐根进行液压试验Anchor bolt地角螺栓Anchor plate支撑板Angle beam examination横波检验法Angle of diagonal with longitudinal line对角向线与纵向线的夹角Anti-corrosive coating防酸腐蚀的涂层Anti-galling防卡滞的Any group of aligned indications任何一群或直线分布的显示Any non-hazardous liquid任何非危险性液体Any reduction in thickness任何厚度削薄Any taper at a welded joint焊接接头的任何斜度Apex angle顶角,half-apex angle半锥顶角Apparatus仪器，设备Applied linings,tightness应用忖里,密封性Approval of new material新材料的批准Appurtenances附属零件Arc or gas welded(W)电焊或气焊Pressure welded(P)压力焊Brazed(B)钎焊（Electric）resistance welded (ERW)电阻焊Arc weld电弧焊Act stud welding电弧螺柱焊Resistance stud welding电阻螺柱焊Atomic hydrogen原子氢焊Stud螺栓焊Electron beam welding电子束焊Flash闪光焊Electroslag电渣焊Explosive爆炸焊Induction感应焊Continuous/intermittent welding连续焊/间断焊Electro-gas welding气电焊Full penetration welding 全熔焊Inertia and continuous drive friction welding 用储能和连续驱动摩擦焊/惯性…Laser beam激光束焊Capacitor discharge welding电容放电焊Manual welding:flat position,vertical position手工焊：平焊、立焊Oxy-fuel gas氧燃料气焊Thermit铝热焊Spot 点焊line线焊seam缝焊Tack/Tack weld定位焊Arc strikes,gouges,and other indication of careless workmanship引弧斑痕，刨痕及其他由于疏忽造成的损失starts引弧stops止弧Arithmetical average deviation计算平均偏差Around openings for welded attachment环绕焊接附件孔口Around openings环绕开孔Arrangement symmetry对称布置Arrangement symmetry对称布置equispaced midspan 跨中均布Asbestos with suitable binder含有适当粘剂的石棉ASME designated organization--ASME指定机构ASME designee----ASME代表ASNT=American society for nondestructive testing美国无损检测协会ASTM=American society for testing and material美国试验材料协会At elevated temperature,在高温情况下/cryogenic低温下At increments that are within20%of the range covered----（点与点间的）增量应为所覆盖范围的20%At or near the center of the weld在焊逢中间或附近At shop在车间At the edges of the fillet weld在角焊缝焊趾处At the large end在大端At the max.anticipated temperature最大预期温度下At the most critical area最危险的区域At the purchaser’s option基于买方的选择At the smallest cross sectional area在最小横截面Attachment of pressure parts to flat plates to form a corner joint承压件、平板相焊形成角接头Attachment welds连续焊逢Austenitic chromium-nickel stainless steels奥式体铬镍不锈钢Austenitic stainless steel奥式体不锈钢Authentication认证/鉴定Auto-refrigeration自动制冷Average discontinuity hoop stress不连续环向平均应力Avoid overloading the bristles避免刷上沾太多油漆Avoid sharp break避免尖角破裂Axial load per unit circumference单位周长轴向载荷Axial strain轴向应变Back strip剥离Back-chip背面清根Backing device钩圈Backing plate,clad material覆层材料的垫板Backing strip垫板Baffle cut折流板切口Baffle plate起顶板，挡板Baffle折流板Bare and marred spots裸露点（未上漆的）和损害了的地方Bars and shapes棒材和型材Bars拉杆jacks千斤顶clamps夹具Bar棒Base metal母材Base plate底板Base tube基管Basis for establishing确定的基础Bcup硼铜磷组BAg硼银组Be applied as a continuous coating in an even manner to achieve a minimum film thickness平坦，最薄的膜Be available in sufficient quantity应有足够用的量Be brought up uniformly to均匀升温Be chamfered or rounded进行倒角或倒圆Be compatible with与…协调、一致Be conducted on water at a tem.Between..and..应采用温度在..和..之间的水来进行Be disconnected隔断Be either staggered or in-line可以相互错开，或并排布置Be erected at the manufacturer’s works在厂内试安装Be essentially symmetrical with respect to the axis of rotation相对于旋转轴保持基本对称Be examined by sectioning可进行截面检查Be expanded for the full thickness of the tube sheet管只能在管板整个厚度里胀Be explicitly indicated that the unit is subjected to vibrations明确指出换热器会有振动Be formed to the curvature of the shell做成与壳体相对应的曲率Be forwarded to送交Be identified in yellow以黄色标明Be inspected to ascertain complete penetration检查确定是否Be mandatory for强制性的要求Be multiplied by乘以Be obstructed by被…堵塞Be of streamlined design设计成流线型Be perpendicular to垂直于Be readily rendered inoperative经常失灵Be ready accessible for inspection便于检查Be sampled进行采样Be solution annealed进行固溶退火Be well ground,not cake,thicken or skin（油漆）安放好、不结块、变浓、或结皮Be written in stencil on the yellow bandBead width焊道Beams梁Bearing area承载面积Bearing surface受压面Bend tangent弯处切点Bend test弯曲试验Bending stress弯曲应力Bend弯管Bessemer quality steel贝式体钢Bevel is optional,45°max.斜度/坡口任意，最大为45°Bevel斜磨/倒角Bind flange法兰盖/盲法兰Black ground,yellow letter黑底黄字Blank flange盲板法兰Blast cleaned surface喷砂清洗过的表面Blow敲击,peening锤击Body-to-bonnet or body-to-yoke bolting阀体和阀盖，阀体和阀轭螺栓Boiler water锅炉水Bolt hole clearance螺孔间隙Bolt lands螺栓载荷Bolt stress螺栓应力Bolt tensioners螺栓紧固件/螺栓张紧Bolted flange connection螺栓法兰连接Bolting flange 螺栓法兰Bolt螺栓Bonnet封头管箱Booster gas heater增压气加热器Bosses threadsBottom plate of saddle鞍座底板Bottom plate底板Braced and stayed surface拉杆和撑杆表面Braces or stay-bolts of uniform diameter symmetrically spaced等直径并对称布置的拉撑件或撑条的表面Brace拉杆Bracing拉筋Branch connection支管连接Brazed connections for nozzle接管的钎焊连接Brazed joint钎焊接头Brazed vessel钎焊容器Brazer钎焊工Brazing filler metal ring pre-placed here钎料环预先安放于此Brazing filler metals钎料Breaking pin device安全销装置Breaking pin housing安全销套Breaking pressure破碎压力Breather valve呼吸阀Brinell hardness布氏硬度Brittle coating脆性涂料Brittle fracture脆性破坏BUB=bubble point沸点Bubble trays泡罩塔Buckling stress屈曲应力Built-up pad加厚凸缘上Burrs along the hole periphery shall be removal除去管孔周边毛刺Burr毛刺,毛口Busting test爆破试验But otherwise by…但用其他..方式则不Butt straps对接盖板/对接搭板Butt welded joint对接接头Buttering预堆边焊Buttstraps对接搭板Butt-welding对接焊By capillary attraction借助于毛细管引力Bypass shroud旁路挡板By-pass旁通管Cable clamp索夹Calculated test pressure计算得的试验压力Calculation heat exchanger area计算换热面积Calibrated against a standard deadweight tester经标准的静重式测试仪校正Calibrated at intervals not exceeding six months每隔六个月复检一次Can section罐段head端部exchanger section换热器段nozzle管嘴Capacity certification of pressure relief devices泄压装置排量证明书Capacity certification test排量的验证试验Carbon content含碳量Carbon in material for welding焊接用材料中的碳Care for handling小心轻放HANDLE WITH CARE: Indicating that contents are fragileCast bronze threaded fittings铸造青铜螺纹连接管配件Cast copper alloy pipe flange铸铜合金公称管法兰Cast ductile vessel可锻铸容器Cast iron circular dished heads铸铁碟形封头Cast iron pipe fittings铸铁管件Cast iron vessel铸铁容器Cast iron plugCast iron standard parts,small铸铁标准部件，小件Cast iron铸铁/生铁Cast material铸造材料Cast,forged,rolled,or die formed standard pressure parts铸，锻，轧，或模具成形的标准受压件Casting quality factor铸造质量系数Casting铸件Catalyst circulation design case催化剂循环设计情况Catch basins滤污器Category B butt joint--B类对接接头Category容器类别Caustic service有腐蚀的设备Caustic soda苛性钠Caustic washing tower/alkaline tower碱洗塔Center of gravity mark重心标识NIL:Indicating position of center of gravityCenter of lap搭接中心线Center of weld焊缝中心线Centrifugal castings离心浇注的铸件Ceramic random packing陶瓷散堆填料Certificate of authorization for code symbol stamp规范符号标志的认可证书Certification of nondestructive personnel无损检验人员证明书Certified individual（CI）合格人员Chamfer for pass partition oral part隔板槽倒角Chamfer倒角Channel box管箱Channel cover管箱平盖Channel flange管箱法兰Channel gasket管箱垫片Channel head管箱封头Channel pass partition管箱分层隔板Channel-side gasket管箱侧垫片Charpy impact tests“夏比”冲击试验Charpy V-notch type夏比V形缺口形式Chart草图Checking of Dimension校核尺寸Cheesecloth粗棉布Chemical analysis for qualification shall be obtained by laboratory methods评定化学分析应当采用化验室分析方法Chemical analysis verification results化学分析验证结果Chemical cleaning connections化学清洗连接处Chemical composition化学成份Chiller economizer再接触预冷器China state bureau of quality and technical supervision 中国质量技术监督局Chip mark on integrally forged vessels整体锻造容器上的缺口标志Chip marks and minor depressions削痕或较小的凹陷Chipping铲chipping hammers;grinding磨abrasive wheels;scraping刮scrapers;gouging刨Chisel凿子chrome-moly steel铬钼钢Chrome铬钢Chromic acid铬酸Circular heads and noncircular heads圆形和非圆形封头Circular plates圆平板Circumferential butt joints with one plate offset单边折边的环向对接接头Circumferential joint环向连接longitudinal joints纵向接头ring joint圆环形连接Circumferential stress环向应力Circumferential surface圆周表面Circumferential weld环焊缝Clad material覆层材料Clad plate复合板Clad restoration覆层复原Clad sheet复合薄板Clad side覆层侧Clad vessel覆层容器Cladding覆层Clad-stripped surface剥离了覆层的表面Clamp ring夹环Clamp卡箍Clapboard挡板Class of acceptance合格级别Class of welded details焊接细节的类别Classification number牌号Clay treater feed heater白土塔进料加热器Cleaned with a light,non-residue,and chemical solvent使用轻型、无残留化学熔剂Cleaning and developing solution清洗和显影法Cleaning of brazed surfaces钎焊的表面清理Cleaning of welded surface焊件表面清理Clearance between surfaces to be brazed钎焊表面间的间隙Clearance间距Clips夹板/压板/夹持件/夹板/卡子Closing in extensions of the body筒体延伸部分进行收口Closing plug塞堵,cap帽盖Closure bars拉紧杆Closure封闭Clustered indication密集性显示CMGC波齿垫CMR阶梯型填料Coarse ingot structure粗锭结构Coarse ripple粗糙焊波grooves沟槽overlaps焊瘤abrupt ridges陡脊valleys凹坑Cracks裂纹pinholes 针孔incomplete fusion未熔合Crater弧坑Coated and cored electrodes and flux带涂层的及药芯的电焊条和焊剂Coated electrodes涂层焊条Coated surface涂漆了的表面Coated with a metallic base waterproof lubricant to prevent galling in use and aqueous corrosion during testing漆上金属防水润滑剂以防止卡滞及在试验过程中出现的水腐蚀Coatings涂层plating电镀Code for construction and acceptance of spherical tanks球形储罐施工和验收规范GB50094Code number代码Code symbol规范符号Coiler蛇管，盘管Cold bent冷弯Cold differential test pressure冷差试验压力Cold flash drum feed cooler冷闪蒸筒进料冷却器Cold-drawn bars冷拔棒Collapsing pressure垮塌压力Collar boltColor coding色码Column立柱Column塔器Combination of different material不同材料组合Combination units组合容器Combined with pneumatic与气压试验混合Combine-unit组合件Combustible distillates可燃液体Commodity specification--设备规格书Communicating chambers连通室Complete chemical analysis of the overlay完整的堆焊层化学分析Complete fusion and complete joint penetration完全熔合及完全焊透Composite组合件Compresed asbestos gaskets压紧的石棉垫Compressed air service压缩空气锅炉Compression type压环式Compressors压缩机Computation计算Computed working pressure from hydrostatic test由水压试验计算的工作压力Computer control module计算机控制模数Concave and convex凹面和凸面Concavity凹陷Concentric reducer sections同心变径段Concentric ring wave form disk plate同心环碟片填料Concert with inner surface与内表面吻合Conditioned areas修整区域Cone锥体Conical head锥形封头Conical reducer sections锥形变径段Conical sections圆锥截面Connection size standard连接尺寸标准Conspicuous location显眼的位置Constant volume process zone定容过程区Construction fixtures建造夹具Construction结构数据Consumable and non-consumable electrode process熔化电极法与不熔化电极法Consumable inserts焊接用可熔化嵌条Contact facing接触面Contact pyrometers接触高温表Contamination污染物recontamination再污染Continuation of shell optional壳体可延伸Continuous full penetration weld连续全焊透焊逢Continuous heat resistance持续耐热Control of stamping打印管理Controlled shot peening控制喷丸Conversion换算Coolant冷却剂Cooling chamber冷却室Cooling rate降温速度Cooling tower fan冷却塔风机Cooling way and time冷却方式与时间Copper sulfate etching硫酸铜Corner and fillet圆角和倒角Corner joint角接头Corner or tee joints角接或T型接头Corner,fillet角接焊缝，角焊缝Corrected for temperature温度校正Corrections for moisture content of the steam校正蒸汽的含水量Corroded thickness蚀态厚度Corrosion resistant linings防腐蚀忖里Corrosion resistant weld metal overlay cladding抗腐蚀堆焊金属层Corrugated metal,asbestos inserted,or corrugated metal,jacketed asbestos filled内填石棉的波纹状金属或充填夹层石棉的波纹金属Corrugated plate波形板Corrugated shells波纹形壳体Corrugating paper machinery波纹板机械Corrugating paper machinery瓦楞纸机械Cosmetic grinding休整性打磨Counter-current逆流/回流Coupling threadCouplings plugged to prevent damage塞紧以防损坏Coupling管箍/耦合/联结Cover flange外头盖法兰Cover plates/Cover盖板Cracks裂纹seams皱纹laps折叠cold shuts冷隔lamination分层Cradle吊架Crater crack火口裂纹Crimping强压Critical temperature临界温度Cross stray斜撑Curvature of the vessel wall容器壁的弧度，Curvature 曲率Cutting oil切削油scale residues剥落的残渣Cutting切割fitting装配and alignment对准CVN impact testing夏比缺口冲击试验Cyclic operation循环工作Cyclical loading循环载荷Cylinder筒体Cylindrical shell柱状壳体，Cylindrical圆柱形Damp潮湿greasy油污oxidized氧化Dead load静载荷Defective brazing有缺陷的钎焊Defect缺陷Defined limit规定的范围Deflecting baffle导流板Deflection cause linkage挠曲引起泄露Deflector导流装置Delayed cracking延迟裂纹Demister破沫器Demonstration of density and penetrameter image射线透照的黑度和透度计Dengsity密度Velocity流速pressure drop压降viscosity粘性molecular weight分子量Density密度Deoxaluminite weld-through primer焊接坡口防护涂料Deoxidation脱氧Depentanizer feed-bottoms exchanger脱戊烷塔进料/塔底换热器Deposited weld metal熔焊金属Depth of offset折边深度Derusting去锈Design and construction of large,welded,low pressure storage tanks大型焊接低压贮罐设计和制造API620 Design duty设计功率Design for full vacuum@temper.Design life设计寿命Design margin设计裕度Design or type number of valve阀门设计号或型号Design parameter设计参数Designation名称Detachable chamber独立可分的受压室Detect pressure观察压力Detect surface calibration notches检测表面标定缺口Detrimental corrosion有害的腐蚀Detrimental discoloration有害变色Deviation背离，（对角线、角度上的）偏差DEW=dew point露点Diagonal white and yellow bands白黄色斜纹Dial indicating pressure gages表盘指示压力表Diameter exemption直径的豁免Diaphragm type pressure relief valve隔膜式泄压阀Die-stamping for material identification打材料标志硬印Diff.Pressure/Differential pressure压差Differ in thickness厚度差Diffusible hydrogen limit扩散氢限制Digital reading pressure gages数字压力表Dimensionless factor无量纲系数Dimpled压凹窝的,embossed使凸出Direct firing(DF)直接火容器Discharge of safety valves安全阀泄放Discharge pipe排放管Discharge出料Dished cover球面凸形封头Dished heads碟形Disk-doughnut baffle盘-环行折流板Dismantling拆除installation安装Displacement measurement test位移测量试验Dissimilar metal welding异种金属焊接Dissimilar weld metal不同金属的焊接Distortion大变形Distribution devices配电装置Distribution,retention发送，保存Distributor分布器Double curvature双曲率single curvature单曲率Double pipe套管Double weld双道焊Double-jacketed金属包垫片Double-welding双面焊Doubly curved shell两个曲面组成的壳体Dowel销子Drain opening排尽孔Drainage排放Drilled or bored holes钻孔或镗孔Drips and runs in the path of the weld joint焊道内的防护涂料滴痕或流痕Driving fit打入配合（封头与壳体焊接前）Drop weight test落锤试验Drum圆桶Dry saturated steam干饱和蒸汽Dry weight of total halogen or sulfur or in-organic halogens总卤素或硫或无机卤素干重Ductile cast iron可锻铸铁Due to fatigue or creep由于疲劳或蠕变Dummy tubes O.D.堵管平盖Duplex stainless steel双相不锈钢Duplicate and similar parts相同件和相似件During fabrication/Fitting up制造过程中制造期间Dye penetrant examination of the completed weld--100%的着色渗透探伤Dye stenciling染色镂刻Dye-penetration detection着色探伤Dynamic loading动载荷Each bundle每捆,each lift每个吊运包装,shipping container集装箱Each side of each circumferential welded intersection 每一环向接头相交的两侧Earth lug接地板Earth lug接地板anchor bolt地脚螺栓lifting lugs吊耳Eccentricity of shell壳体的偏心度Eddy current test涡流探伤with eddy current method Edge defects边缘缺陷Edge of plates,metal removal from由加工板边去除金属Effective gasket width有效垫片宽度Effective temp.Difference有效温差Effective thickness of conical section锥形段的等效厚度Efficiency系数Elastic buckling stress弹性失稳应力Elasticity,modulus of弹性模量Elastomer合成橡胶Elbow弯头Electrode core焊芯Electrode rods电焊条electrode wires电焊丝Electrode焊条Elevation above ground拔高/地面高度Ellipsoidal椭圆形,torispherical碟形,hemispherical 半球形,conical锥形Ellipsoidal椭圆形hemispherical半球形spherically dished(torispherical)球面凸形（碟形）conical锥形tori-conical(cone head with knuckle)折边锥形（具有转角区的锥形封头）Elliptical projection technique椭圆发射技术Elongated indication条型显示Embody包含，体现Embrittlement脆化Employing straight threads使用直螺纹Enameled vessel搪瓷容器Enamel瓷釉Endurance limit疲劳极限Engineering drawings工程设计图纸commodity specification商品规格书Engraving or hard stamping蚀刻或打钢印Enlarged inlet nozzlesEnthalpy-temperature profile:linear热函-温度曲线图：线性的Entirely in spherical portion全部在球体部分Epoxy环氧涂层Equally spaced on two rows均匀分布为两排Equipment setup,calibration,operation,evaluation of examination设备调试、校准、操作、和检测数据评定Equip-spaced mid-span跨中均布Erection weight安装重量Erosion冲蚀Establish a mean analysis确定化学成分平均值Etchant浸蚀剂Etching,of sectioned specimens侵蚀，关于截面试样Evaluation and retests评片与复验Evaporator蒸发器Examination of sectioned specimens剖面试样的检验Examination report（超声波）探伤报告Locate indication area确定指示区域echo height回波高度indication dimensions指示尺寸depth below the surface表面下的深度type of indication指示类型Examined by审核人Excess stock from…material余料Excessive deformation过大的变形Excessive scoring of the plates平板上的深痕Exothermic kits放热包Expanded connection胀接Expansion joint膨胀节Explosion-proof group防爆等级Explosive welding of multiplayer tubes多层管爆炸焊Exposed inside edges内侧裸露出的边缘Exposed left un-welded留下不予焊接的显露部分Extend over…延伸到…Extended heat transfer surfaces延伸的转热面Extended or thickened necks加长或加厚管颈External B31.1process piping外部B31.1工艺配管External surface painting STD.外表面涂漆标准Extract column feed-bottoms exchanger抽出液塔/塔底换热器Extract column抽提塔Extreme fiber elongation最大纤维伸长率/极限Eye bolts吊环螺栓Fabricated castings for pump泵外壳Fabrication单纯的机械制造Facilities装备Facing to C.L.or W.L.伸出高度Factory-made wrought butt-welding fittings工厂制造的锻钢对焊管配件Failure likelihood失效频率Failure or deterioration of the diaphragm material隔膜材料失效或损坏Failure probability失效概率Fatigue strength design疲劳分析设计Female thread内螺纹,male thread外螺纹Ferric steel vessel with tensile property enhanced by heat treatment经热处理后提高抗拉性能的铁素体钢容器Ferrite number(FN)铁素体含量代号Ferritic steels with tensile properties enhanced by H.T.采用热处理提高抗拉性能的铁素体钢Ferromagnetic铁磁性（材料）Non-magnetic非磁性（材料）Ferrule-type卡套式Field assembly of vessel容器的现场安装Filler metal填充金属Filler plugs for trepanned holes锥孔的管塞Fillet weld角焊Film coefficient膜系数Filter and traps used to collect water and oil过滤器和积水箱Filter screen滤网Fine metal gauze细丝网Finish coat面漆Finish:“face”sweep blasted抛光：标明“面”处需抛光处理Finishing column feed-bottoms exchanger成品塔进料/塔底换热器Finned portion,un-finned portion有翅段，无翅段Fired heater coils火焰加热炉盘管Fired process tubular heater直接火管式加热炉Firmly adherent deposits牢牢黏附的沉淀物First lot of…首批..First sample test report首样测试报告Fitting attachments附件装配Fitting up joints连接处的装配Fittings配件Fixed saddle固定鞍式支座Flaking剥落，薄片Flame arrestor火焰清除器Flame cutting火焰切割Flame damper阻火器Flame/Explosion-proof stirrer防爆搅拌器Flammable vapor可燃蒸汽Flange contact facings法兰接触面Flange moment法兰力矩Flange of stiffener加强圈翼板Flange rings法兰圈Flange stress法兰应力Flanged fittings带法兰管配件。

英文版Excel 中英文对照表激活（activate）数组（array）数组公式（array formula）相关联的数据透视表(associated PivotTable report ) 自动套用格式(autoformat)坐标轴(asix)基础地址(base address)“合并计算”表(consolidation table)比较条件(comparison criteria)比较运算符（comparison operator）常量(constant)单元格引用(cell reference)当前区域(current region)分类轴(category asix)分类字段(category field)复制区域(copy area)计算列(calculated column)计算项(calculated item)计算字段（数据库）(calculated field)计算字段（数据透视表）(calculated field)列标题(column heading)列字段(column field)条件(criteria)条件窗格((criteria pane)条件格式(conditional format)图表工作表(chart sheet)图表区(chart area)修订记录(change history)约束条件(constraints)证书验证机构(certifying authority)自定义计算(custom calculation)垂直线(drop lines)从属单元格(dependents)明细数据(detail data)默认工作表模板(default worksheet template)默认工作簿模板(default workbook template)默认启动工作簿(default startup workbook )目标区域（destination area）数据标签(data label)数据标志(data marker)数据表(data table)数据表单(data form)数据窗格(data pane)数据点(data points)数据库(database)数据区域(data region)数据系列(data series)数据有效性(data validation)数据源(data source)数据源驱动程序(data source driver)图表数据表(data table in charts)下拉列表框(drop-down list box)值区域(values area)值字段(value field)表达式(expression)嵌入图表(embedded chart)外部数据(external data)外部数据区域(external data range)外部引用(external reference)误差线(error bars)编辑栏(formula bar)公式(formula)公式选项板(Formula Palette)函数(function)函数筛选(filter)填充柄(fill handle)字段（数据库）(field)字段（数据透视表）(field)单变量求解(goal seek)图表中的网络线(gridlines charts)组(group)冲突日志工作表(history worksheet)高低点连线(high-low lines)插入行(Insert row)迭代(iteration)绝对交集(implicit intersection)内部连接(inner join)输入单元格(imput cell)索引(index)项(item)连接(join)连接线(join line)锁定的字段或记录(locked field or record) 图例（legend）图例项标示（legend keys）合并单元格(merged cell)活动选定框(moving border)矩阵(matrix)移动平均(moving average)映射范围(mapped range)操作数(operand)分级显示(outline)分级显示符号(outline symbols)分级显示数据(outline data)脱机多维数据集文件(offline cube file)外部连接(outer join)运算符(operator)磅(point)保护(protect)报表筛选(reporter filter)参数parameter参数查询parameter query打印标题print totles打印区域print area分页符page break分页预览page break preview绘图区plot area密码password数据透视表PivotTable report数据透视表分类汇总PivotTable sobtotal数据透视表列表PivotTable list数据透视表数据PivotTable data数据透视表总计PivotTable grand totals数据透视图报表Pivotchart report数据透视图分类字段Pivotchart category field 数据透视图系列字段Pivotchart series field透视区域pivot area引用单元格precedents粘贴区域paste area主键primary key属性字段property fields查询queryExcel函数大全数据库和清单管理函数DA VERAGE (daverage) 返回选定数据库项的平均值DCOUNT (dcount) 记算数据库中包含数字的单元格的个数DCOUNTA (dcounta) 记算数据库中非空单元格的个数DGET (dget) 从数据库中提取满足指定条件的单个记录DMAX (dmax) 返回选定数据库项中的最大值DMIN (dmin) 返回选定数据库项中的最小值DPRODUCT (dproduct) 乘以特定字段（此字段中的记录为数据库中满足指定条件的记录）中的值DSTDEV (dstdev) 根据数据库中选定项的示例估算标准偏差DSTDEVP (dstdevp) 根据数据库中选定项的样本总体计算标准偏差DSUM (dsum) 对数据库中满足条件的记录的字段列中的数字求和DV AR (dvar) 根据数据库中选定项的示例估算方差DV ARP (dvarp) 根据数据库中选定项的样本总体计算方差GETPIVOTDATA(getpivotdata)返回存储在数据透视表中的数据日期和时间函数DATE (date) 返回特定时间的系列数DATEDIF (datedif) 计算两个日期之间的年、月、日数DATEV ALUE (datevalue) 将文本格式的日期转换为系列数DAY(day) 将系列数转换为月份中的日DAYS360 (days360) 按每年360天计算两个日期之间的天数EDATE (edate) 返回在开始日期之前或之后指定月数的某个日期的系列数EOMONTH (eomonth) 返回指定月份数之前或之后某月的最后一天的系列数HOUR （hour）将系列数转换为小时MINITE (minite) 将系列数转换为分钟MONTH (month) 将系列数转换为月NETWORKDAYS (networkdays) 返回两个日期之间的完整工作日数NOW (now) 返回当前日期和时间的系列数SECOND (second) 将系列数转换为秒TIME (time) 返回特定时间的系列数TIMEV ALUE (timevalue) 将文本格式的时间转换为系列数TODAY (today) 返回当天日期的系列数WEEKDAY (weekday) 将系列数转换为星期WORKDAY (workday) 返回指定工作日数之前或之后某日期的系列数YEAR(year) 将系列数转换为年YEARFRAC(yearfrac)（返回代表START_DATE（开始日期）和END_DATE（结束日期）之间天数的以年为单位的分数DDE 和外部函数CALL(call) 调用动态链接库(DLL)或代码源中的过程REGISTER.ID(register.id) 返回已注册的指定DLL或代码源的注册IDSQL.REQUEST (sql.request)连接外部数据源，并从工作表中运行查询，然后将结果作为数组返回，而无需进行宏编程。