军工宇航IC配件部件说明书-厦门天络纬

航芯芯片调试器使用手册Version1.0上海爱信诺航芯电子科技有限公司条款协议本文档的所有部分，其著作产权归上海爱信诺航芯电子科技有限公司（以下简称航芯公司）所有，未经航芯公司授权许可，任何个人及组织不得复制、转载、仿制本文档的全部或部分组件。

本文档没有任何形式的担保、立场表达或其他暗示，若有任何因本文档或其中提及的产品所有资讯所引起的直接或间接损失，航芯公司及所属员工恕不为其担保任何责任。

除此以外，本文档所提到的产品规格及资讯仅供参考，内容亦会随时更新，恕不另行通知。

版本修订目录1.简介 (5)2.AC-Link V2概况 (5)3.AC-Link V2仿真/调试器特点 (5)4.AC-Link V2仿真/调试器使用指南 (6)5.其他 (9)图表1AC-Link V2仿真/调试器框图 (5)图表2AC-Link V2实物图 (6)图表3AC-Link V2接口引脚说明 (6)图表4选择驱动程序 (7)图表5选择端口 (7)图表6更新驱动程序 (8)图表7选择AisinoChipCDC.inf (8)图表8成功安装驱动程序 (8)1.简介AC-Link V2仿真器是一款遵循ARM公司的CMSIS-DAP标准开发的调试工具，支持航芯(AisinoChip)旗下所有的Cortex-M系列MCU产品。

为用户提供了一款小巧便携、安全可靠、低成本的仿真/调试器。

2.AC-Link V2概况AC-Link V2仿真器调试框图如图表1所示，主要由仿真器和通信设备类（Communication Device Class,CDC）驱动软件组成。

图表1AC-Link V2仿真/调试器框图3.AC-Link V2仿真/调试器特点1)在线调试的功能－支持目标板3.3V或5V自供电环境；－即插即用，不需安装驱动，可直接在Keil，IAR Embedded Workbench等集成开发环境（Integrated Development Environment,IDE）下调试；－支持串行线调试（Serial Wire Debug,SWD）接口。

天宇-C93T产品手册-20140329天宇光电 GPS 产品系列天宇 C93T产品手册广州天宇光电仪器有限公司二○一四年三月第一章天宇C93T GPS概述§1.1 关于天宇C93T GPS介绍作为先进的测绘技术，GPS测量技术在众多测量生产中的作用变得日益广泛和重要。

天宇光电一如既往打造中国测绘仪器高端，紧随世界先进测量技术的发展，自助攻关研发，牢牢掌握了测绘仪器领域所有先进核心技术，再次为全国测绘仪器用户献上一场GPS的“饕餮盛宴”。

天宇C93T GPS主机，集成了天线、主板、电台、接收天线、蓝牙模块、电池等组件，移动站完全一体化，只需手簿操作即可工作。

天宇C93T GPS系统结合了最新的GPS RTK 接收机的先进技术并以精巧的外观，迷人的色彩给你带去时尚的测量模式。

天宇C93T GPS，依靠先进的GPS接收机技术在设计上着重于更高的稳定性，更低的功耗，更小的体积，更轻的重量。

天宇C93T GPS，在防水、防尘方面有独特的设计。

电池和内置电台都安放于主机的底部，更有效的防水防尘。

§1.2 四大特色1、一体化设计与抗干扰的完美结合一体化设计是世界同类产品的潮流，彻底摆脱“线”制，模块化的设计有效解决机器内部的干扰问题。

2、专业设计的数传电台，误码率低，方便写频掌握核心的数传电台技术，主体性能达到国外先进水平，方便写频，为客户解决串台问题，误码率在10-7。

3、工业级模具三防设计（防尘、防水、防震）专业的模具、高强度的工业外壳材料以及具有很强防水能力的防水圈，使得C93T GPS的野外性能更优越。

4、双接口（USB、串口）高速传输，4G大内存。

除了一般仪器用的COM口外，天宇C93T GPS采用USB的串行口连接技术方便大容量静态数据的传输。

内置4G内存，可以满足静态连续一秒间隔采集一个星期以上，若采集间隔增大，存贮时间还将成倍增加。

§1.3 技术特色1、科技传承融会贯通核心的RTK数据链技术，主体性能达到国际先进水平；双键飞梭的方便操作，轻松实现各种主机功能操作；无线的蓝牙通讯方式；工业级的三防设计等多年来掌握并实践的先进RTK技术在C93T GPS中得到传承，使得主机的稳定性得到有效的保障。

9312排障手册目录Contents一、前言 (2)目的 Purpose (2)听众对象Audience (2)二、Alcatel-Lucent_9312硬件介绍 (3)1、9312 NodeB结构： (3)2、各个模块功能： (3)（一）d2U模块 (4)（二）TRDU模块 (4)3、机柜内连线方式： (5)4、D2U的调测： (6)（一）调测前的准备： (7)（二）软件升级： (7)（三）修改I&C参数和保存I&C参数： (7) （四）备份MCA参数： (9)（五）调测结束。

(9)三、基站故障现象及解决方案 (9)1、小区问题及解决方案： (9)2、传输问题及解决方案： (11)3、脱管问题及解决方案： (13)4、D2U本调时常遇问题及解决方案： (14)一、前言目的 Purpose这篇文档描述了Alcatel-Lucent 9312基站的硬件介绍，开通以及故障处理。

听众对象Audience安装督导，基站维护人员等其它用户。

本文件适用于Alcatel Utran工程项目9312及混插设备的故障处理。

Radio parts: TRDUICOTRCU二、 Alcatel-Lucent_9312硬件介绍1、9312 NodeB 结构：注：optional 为可选模块，有些基站没有配备这些模块。

2、各个模块功能：（一）d2U模块1、x-CCM-U板是核心控制模块，控制OAM管理。

部分呼叫处理和内外部的数据流交换和结合，支持内外部告警连接和外部同步参考接口。

（附下图）2、x-CEM-U板是信道单元模块，主要功能单元有：—基带单元——执行基带信号处理功能。

—接口控制单元——为基站提供数据，控制和时间接口。

也执行x-CEM-U控制管理功能。

（附下图）（二）TRDU模块TRDU是一个具有以下功能的单模块：—无线收发器（数字信号处理和射频调制解调）—功率放大器—低噪音放大器—双工器（附下图）3、机柜内连线方式：D2U的连线包含以下几种：第一、电源线。

Y o u r C o n n e c t o r C o n s u l t a n t S i n c e1962M85049/128EMI/RFI ShieldTermination BandsKey Benefits of Termination Bands:►Easy to Terminate►Secure Tension Lock System►For Cost Effective ApplicationsSPACECRAFT C OMPONENTS T ERMINATION B ANDSThese Bands are commonly used to attach a braid or a shield to a backshell. They come in two shapes: Coiled or flat.To provide our customers with a cost effective solution, Spacecraft Components now manufactures Termination Bands and is qualified to the M85049/128 specification.Shown below is a summary of the various bands and their respective tools.ELECTRO- ADAPTER SHAPE SIZE SCP P/N MILITARY REFERENCE MILITARY TOOL NON MILITARY APPLICATIONSELECTRO-ADAPTER TOOLDANIELS TOOL214LF002Flat .245 x 14.0SCPSE-02F M85049/128-1M81306/2-01▲EAK214-25▲DBS-1101▲214L0002CoiledSCPSE-02CM85049/128-2BAND-IT ®SHAPE SIZE SCP P/N MILITARY REFERENCE MILITARY TOOLSNON MILITARY APPLICATIONSBAND-IT ®TOOLSDANIELS TOOLS GLENAIR TOOLSA10089Flat .242 x 14.25SCPBE-02F M85049/128-3M81306/1-01●A40199●DBS-2100●600-058●A10088Coiled SCPBE-02C M85049/128-4A11086Flat .242 x 18.00SCPBE-02FL18♦N/A A31189*Flat .120 x 8.125SCPBE-04F M85049/128-7M81306/1-02●A30199●DBS-2200●600-061●A31188*Coiled SCPBE-04C M85049/128-8A31089*Flat.120 x 14.30SCPBE-03FN/A* Mini Band♦ Two-piece construction GLENAIR SHAPE SIZE SCP P/N MILITARY REFERENCE MILITARY TOOLS NON MILITARY APPLICATIONSGLENAIR TOOLSBAND-IT ® TOOLSDANIELS TOOLS600-052Flat .242 x 14.25SCPBE-02F M85049/128-3M81306/1-01●600-058●A40199●DBS-2100●600-052-1Coiled SCPBE-02C M85049/128-4600-090Flat .242 x 18.0SCPBE-02FL18♦N/A M81306/1-01●600-058●A40199●DBS-2100●600-090-1Coiled SCPBE-02CL18♦600-057*Flat .120 x 8.125SCPBE-04F M85049/128-7M81306/1-02●600-061●A30199●DBS-2200●600-057-1*Coiled SCPBE-04C M85049/128-8600-083*Flat .120 x 14.30SCPBE-03F N/A600-083-1*CoiledSCPBE-03C* Mini Band♦ Two-piece constructionBand-It ® and Glenair bands work in the DBS or STS Tools, but two operations are required (terminate and fold-over) rather than the one operation (terminate/trim). DBS or STS-1101, and 1201 tools include both the termination tool and the secondary roll-over tool.SUNBANK SHAPE SIZE SCP P/N MILITARY REFERENCE MILITARY TOOLS NON MILITARY APPLICATIONSSUNBANK TOOLSDANIELS TOOLSS 3175F2Flat .245 x 14.00SCPSE-02F M85049/128-1M81306/2-01▲STS-1101▲DBS-1101▲S 3175-2Coiled SCPSE-02C M85049/128-2S 3175F3*Flat .118 x 14.25SCPSE-03F N/A M81306/2-02▲STS-1201▲DBS-1201▲S 3175-3*Coiled SCPSE-03C S 3175F4*Flat .118 x 9.50SCPSE-04F M85049/128-5M81306/2-02▲STS-1201▲DBS-1201▲S 3175-4*CoiledSCPSE-04CM85049/128-6* M ini BandDBS or STS-1101 and 1201 tools include both the termination tool and the secondary roll-over tool.MILITARY REFERENCEMILITARY TOOLS NON MILITARY APPLICATIONSMILITARY SHAPE SIZE SCP P/N Band-It®Daniels GlenairSunbank M85049/128-1Flat .245 x 14.00SCPSE-02F M81306/2-01▲–DBS-1101▲–STS-1101▲M85049/128-2Coiled SCPSE-02C M85049/128-3Flat .245 x 14.25SCPBE-02F M81306/1-01●A40199●DBS-2100●600-058●–M85049/128-4Coiled SCPBE-02C M85049/128-5Flat .118 x 9.50SCPSE-04F M81306/2-02▲–DBS-1201▲–STS-1201▲M85049/128-6Coiled SCPSE-04C M85049/128-7Flat .115 x 8.125SCPBE-04F M81306/1-02●A30199●DBS-2200●600-061●–M85049/128-8CoiledSCPBE-04C●One Step Tool ▲ Two Step Tool3040 Clayton StreetPhone: 702.851.7600 Email:************************North Las Vegas, NV 89032 Fax: 702.851.7620 Web: ® B and-It ® is a registered trademark of Band-It-IDEX, Inc., a division ofIDEX Corporation, of which Spacecraft Components Corp. is not affiliated..098 MAXØ1.120SCPSE-03C.198 ±.031.080 REF.118 ±.010.015 REF14.24 ±.060SCPSE-03FSCPSE-03F & SCPSE-03C TERMINATION TOOLS:DANIELS': DBS-1201▲ SUNBANK: STS-1201▲ M81306/2-02▲ ▲ Two Step Tool.098 MAXØ1.120M85049/128-6*SCPSE-04C M85049/128-8*SCPBE-04CØ0.860.198 ±.031.080 REF.118 ±.010.015 REF9.56 – 9.44M85049/128-5*SCPSE-04F.195 ±.031.053 REF.090 REF.115 ±.010.015 REF8.18 – 8.062.031 REFTAIL LENGTH INDICATOR MARKM85049/128-7*SCPBE-04FM85049/128-5 & M85049/128-6SCPSE-04F & SCPSE-04C TERMINATION TOOLS:DANIELS': DBS-1201▲ SUNBANK: STS-1201▲ M81306/2-02▲M85049/128-7 & M85049/128-8 SCPBE-04F & SCPBE-04C TERMINATION TOOLS:BAND-IT ®: A30199●DANIELS: DBS-2200●GLENAIR: 600-061●M81306/1-02● ● One Step Tool ▲ Two Step ToolM85049/128MINI-BANDS (.115 WIDE)MINI-BANDS (.115 WIDE)M85049/128-83040 Clayton StreetPhone: 702.851.7600 Email:************************North Las Vegas, NV 89032 Fax: 702.851.7620 Web: * M 85049/128-5, -6, -7, -8 are proposed.® Band-It ® is a registered trademark of Band-It-IDEX, Inc., a division of IDEX Corporation, of which Spacecraft Components Corp. is not affiliated..140 MAX.150 MAXØ1.750M85049/128-2SCPSE-02CM85049/128-4SCPBE-02CØ1.750.328 ±.031.100 REF.245 ±.010.019 REF14.31 – 13.94M85049/128-1SCPSE-02F.350 ±.031.130 REF.156 REF.245 ±.010.020 REF14.31 – 14.192.031 REFTAIL LENGTH INDICATOR MARKM85049/128-3SCPBE-02FM85049/128-1 & M85049/128-2 SCPSE-02F & SCPSE-02C TERMINATION TOOLS:DANIELS': DBS-1101▲ SUNBANK: STS-1101▲ M81306/2-01▲M85049/128-3 & M85049/128-4 SCPBE-02F & SCPBE-02C TERMINATION TOOLS:BAND-IT ®: A40199● DANIELS: DBS-2100●GLENAIR: 600-058●M81306/1-01● ● One Step Tool ▲ Two Step ToolM85049/128QUARTER-INCH TERMINATION BANDS (.245 WIDE)M85049/128-2M85049/128-4The termination of EMI/RFI shielding materials is a specialized sci-ence in today’s aerospace wiring systems. Application tooling is a critical factor in the overall performance of the wiring system components.DMC has worked closely with the world’s leading connector acces-sory manufacturers to develop the necessary tooling and acces-sories to meet the stringent demands of aerospace and defense system contractors. The resulting products afford the user many benefits which include:COMPATIBILITY with all currently available termination bands and systems.RELIABILITY through the use of commercially proven components and tool design practice.QUALITY & REPEATABILITY which are assured by a tension system.SERVICE & CALIBRATION – All tools produced by DMC are adjustable, and may be easily checked and set by the user. Also, expendable components such as cut-off blades are available for simple replacement by the user.LONG SERVICE LIFE – Properly maintained band applica-tion tools will produce thousands of reliable terminations.AFFORDABILITY – DMC tools continue to be the most cost effec-tive method to produce reliable wiring system shield termina-tions.Models are available for .250 in. (6.350 mm) and .125 in. (3.175 mm) wide bands from all current suppliers to M85049/128.THE PNEUMATIC BAND APPLICATION TOOL...is a cost effective system that speeds production and im-proves ergonomic conditions which are present when manual tools are used. Band tension is precisely applied by a depend-able pneumatic system which is consistent and repeatable.The tension system of the pneumatic band tool is adjustable, and can be checked by use of the verifcation devices avail-able from DMC. (See pages 68-69.)The cutter blade and other components of the DMC Pneu-matic Band tools are interchangeable with the same serieshand tools. The rugged design and field replaceable blades make the PBT/PMBT series the best choice for production ap-plications where EMI/RFI bands are used to terminate wire harness shielding.THE HAND OPERATED BAND APPLICATION TOOL (REFERENCE AS81306/2)is an excellent choice for many production and maintenance operations. Like the power driven models, they too can be calibrated by the user to provide reliable terminations throughout the service life.The lightweight construction and small “nose” pro-file enable the user to apply termination bands in even the tightest of working areas.EMI/RFI Band Application Tooling byBackshells for Banding, Over Molding or Shrink BootsConnectors withIntegrated Backshells for Banding, Over Moldingor Shrink BootsAS50151 – All Series, Crimp or SolderAS95234 – Reverse Bayonet, Crimp or Solder MIL-DTL-26482 – All Series, Crimp or Solder MIL-DTL-38999 – Series I, II & IIISee Calalog 601 for details.SCPB00SV AS95234(REVERSE BAYONET)SC50SV AS50151(MS 3450)SC76SV MIL-DTL-26482Series 2(MS3476)SC3924SV MIL-DTL-38999Series III (D38999/24)3040 Clayton StreetPhone: 702.851.7600 Email:************************North Las Vegas, NV 89032 Fax: 702.851.7620 Web: SF-403NOV.2014SCP 50151 Style ConnectorsAS95234 Reverse Bayonet ConnectorsSCPT 26482 Style SC1 38999 Series I SC2 38999 Series II SC39 38999 Series IIISCPB SeriesConnector AccessoriesConnectors with Integrated BackshellsHeadquarters3040 Clayton StreetPhone: 702.851.7600 Email:************************North Las Vegas, NV 89032Fax: 702.851.7620 Web: Italy OfficeSpacecraft Components , Sp A Milan, Italy+39 (335] 719.4512Arizona Office2432 W. Peoria Ave.Suite 1192Phoenix, AZ 85029Tel: 602.944.2351Fax: 602.997.0373South Carolina Office 25 Woods Lake Rd., Suite 403Greenville, SC 29607Tel: 954.748.4540Fax: 954.748.4128Florida Office4577 Nob Hill Road Suite 106Sunrise, FL 33351Tel: 954.748.4540Fax: 954.748.4128Try Our Other Connector ProductsGet All of OurCatalogs & Product Brochures on One DiscY o u r C o n n e c t o r C o n s u l t a n t S i n c e 1962COMPILED AND PRODUCED BY SPACECRAFT COMPONENTS CORP.©2014 SPACECRAFT COMPONENTS CORP ., NORTH LAS VEGAS, NV 89032。

VERTICAL MACHININGCENTERPARTS LISTV42iWLEADERWAY CNC TECHNOLOGIES CO., LTD.NO. 36, Ln. 211, Taiming Rd.,Wuri Dist, TAICHUNG 41468, TAIWANTEL: +886-4-2335-0711FAX: +886-4-2335-0986台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F11051主軸頭+立柱單元SPINDLE HEAD + COLUMN UNITV42iW00103500010B0調整檔塊ADJUSTABLE STOPPER3140\SS41200203500012B0滑座壓塊SLIDING BLOCK,ADJUSTABLE BRA3210\SS41400303582170A0主軸頭SPINDLE HEAD1010\3582170A2\FC30100403582171A0立柱COLUMN 1020\3582171A2\FC-30100503582196A0Z軸下摺動罩LOWER TELESCOPIC COVER, Z 9400\SPCCZ100603582197A0Z軸防屑擋板PLATE FOR CHIP 7210\200703582198A0碰塊座支撐架RIGHT DOG BRACKET SUPPORTER SS41100803582199A0微動開關座(Z)MICRO SWITCH BRACKET, Z AXIS 3160\SS41100904800143204微動開關MICRO SWITCH BNS819-B02-D12-61-12-10BALLU1010********B0碰塊座DOG BRACKET 4140\AL(125m/m*3軌)201103500081A0碰塊DOG 3140\SS41(42m/m)201203540007A0碰塊DOG 4140\AL 外購65L101303985075A0線性滑軌-Z軸LINEAR GUIDE9840\#35滾柱型101404080106015直銷(軸承鋼針)PINφ6x15L5801503582201A0主軸頭右側蓋板RIGHT COVER, SPINDLE HEAD7510\SPCC101603582202A0主軸頭左側蓋板LEFT COVER, SPINDLE HEAD7510\SPCC101703582203A0主軸頭前蓋板FRONT COVER,SPINDLE HEAD7510\SPCC101803582204A0主軸聯動管支架CONDUIT BRACKET7210\SPCC101903582205A0主軸頭側壓克力板ACRYLIC PLATE, SIDE OF SPIND4360\ACRY1020********A0主軸頭右側架RIGHT BRACKET, SPINDLE HEAD7510\SPCC1021********A0主軸頭外側蓋板SIDE COVER,SPINDLE HEADSTOCK7510\SPCC102204640065133方型聯動管WIRE CONDUITK Y-CE(CBS65.2)-65x133-(22目)102304210550003總流量控制組COOLANT NOZZLE MANIFOLD J TM-01控制組\5/8"插心1024********B0近接開關座PROXIMITY SWITCH BRACKET 7160\SPCC1025********A0刀具釋放指示牌NAME PLATE4350\AL1<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F16015配重單元COUNTER BALANCE UNITV42iW00103582190A0配重COUNTER BALANCE3070\SS41100203500006C0鏈輪軸固定座SPROCKET SHAFT BRACKET1210\FC-25\3500006A2200303500021A0鏈條滾輪ROLLER3260\S45C400403500022C0鏈輪軸SHAFT SPROCKET 3260\S45C400504060700025C型扣環(軸用)C TYPE RETAINER RING S-25800604400206205深槽滾珠軸承BEARING 6205ZZ800703500416A0配重滑塊SLIDING BLOCK,COUNTER BALANC 4370\MC200803582191A0配重導桿GUIDING ROD, COUNTER BALANCE 4290\圓棒100904062006025軸心固定座SHAFT BRACKET SHF25-M61010********C0滑軌下固定板LOWER FIXED PLATE, GUIDING R 7180\SPCC101103582192A0滑軌上固定板UPPER FIXED PLATE, GUIDING R 7180\SPCC101203582193A0滑軌上固定板支架BRACKET FOR UPPER FIXED PLAT 7180\SPCC101303582194A0鏈條保護蓋(左)PROTECTING COVER FOR CHAIN7510\SPCC101403582195A0鏈條保護蓋(右)PROTECTING COVER FOR CHAIN7510\SPCC101503500023A0鏈條連結螺絲CHAIN CONNECTING BOLT4310\SCM4401604610050073鏈條CHAIN50x73P (含2鏈目)2<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁規 格用量主件品號序號元件品號品 名英文品名2F27004打刀單元V450/V33i/V42iBOSSTING CYLINDER UNIT3180\SS411 00113500008B0增壓缸固定座TOOL RELEASE CYLINDER BRACKE00213500009B0浮動打刀拉座3250\S45C1TOOL RELEASE CYLINDER SEAT00313500019B0固定軸套3290\S45C4FIXED ROD00403980001A0增壓缸(3Tx13L)98801TOOL RELEASE CYLINDER<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F28046主軸皮帶輪單元SPINDLE BELT UNITV42iW/SJ-V15-01ZT-S02(F)00103500011B0主軸馬達固定板FIXED PLATE FOR MOTOR3170\SS41100203971061A0齒型皮帶輪PULLEY3270\S45C染黑\5GT-72T\ψ66100303600135A0軸壓蓋(∮48)SHAFT END COVER3240\S45C100404061248055迫緊環PACKING RING TLK300 48x55200504601035920齒型皮帶(剖溝)PULLEY BELT5GT*35*9201<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F28047主軸皮帶輪單元SPINDLE BELT UNITV42iW/β8i*8000rpm00103500011B0主軸馬達固定板FIXED PLATE FOR MOTOR3170\SS41100203971008A0齒型皮帶輪(5GT-75T)PULLEY3270\S45C100303580161A0馬達軸端蓋SHAFT END COVER3170\S45C100404061232036迫緊環PACKING RING TLK300 32x36200504601035935齒型皮帶(剖溝)PULLEY BELT5GT*35*935mm1<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F13026底座+鞍座+工作台單元BASE + SADDLE + TABLE UNITV42iW00103582172A0底座BASE1030\3582172A2\FC-30100203580410A0地基螺絲(M36*2P)FOUNDATION BOLT3310\S45C600303580411A0地基螺帽(M36*2P)FOUNDATION BOLT3310\S45C600403600047B0墊塊 (地基螺絲)FOUNDATION PAD 3230\S45C600503582001A0噴水座NOZZLE TUBE BRACKET 3150\SS41200603582184A0大護罩前支架FRONT BRACKET, GUARD 7210\SPCC200703582212A0導油槽OIL TROUGH 7520\SPCC100803582173A0鞍座SADDLE 1040\FC-30100903985073A0線性滑軌-Y主LINEAR GUIDE 9840\市購品1010********A0線性滑軌-Y副LINEAR GUIDE 9840\市購品101103582006A0壓塊SLIDING BLOCK 412010601203582183A0螺絲襯套BUSHING 4230\不鏽綱801303582185A0Y軸前摺動罩Y AXIS TELESCOPIC COVER UNIT7400\SPCCZ101403582186A0Y軸後摺動罩Y AXIS TELESCOPIC COVER UNIT7400\SPCCZ101503582187A0Y軸摺動罩支架(上)TELESCOPIC COVER BRACKET7210\SPCC201603582188A0Y軸摺動罩支架(下)TELESCOPIC COVER BRACKET7210\SPCC201703582189A0鞍座下擋屑板BAFFLE PLATE7510\SPCC201803582245A0聯動管連結座CONDUIT BRACKET7210\SPCC101904640015090方型聯動管WIRE CONDUITCECBO02-26x58-222(15P)/R901020********A0碰塊DOG3140\SS41(42m/m)4021********B0碰塊座DOG BRACKET4140\AL(125m/m*3軌)1022********A0碰塊座DOG BRACKET4140\AL(90m/m*3軌)1023********A0碰塊DOG 4140\AL 外購65L2024********B0碰塊座DOG BRACKET 4140\AL(300m/m*2軌)202504800143204微動開關MICRO SWITCH BNS819-B02-D12-61-12-10BALLU202603582168B0微動開關固定座-Y上SWITCH BRACKET 7160\SPCC1027********B0微動開關固定座-Y下SWITCH BRACKET 7160\SPCC1028********A0工作台TABLE 1050\3582174A2\FC-301029********D0螺帽座BALLSCREW HOUSING 1080\FC-25\3581025A2103003560121B0塞頭(工作台)TABLE SEALED CORK3310\SS4116<續下頁>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第2頁主件品號序號元件品號品 名英文品名規 格用量2F1302603103985050A0X軸線性滑軌LINEAR GUIDEBRH35AL2-P-ZZ-L1800 II103203582179A0X軸摺動罩X AXIS TELESCOPIC COVER UNIT7400\SPCCZ203303582180A0X軸摺動罩上支架TELESCOPIC COVER BRACKET7180\SPCC403403582181A0X軸摺動罩支架(左)TELESCOPIC COVER BRACKET7180\SPCC20350*******A0X軸摺動罩支架(右)TELESCOPIC COVER BRACKET 7180\SPCC203603582175A0碰塊座連結塊(X)CONDUIT FOR DOG(X)3180\SS4120370*******A0微動開關座(X)MICRO SWITCH BRACKET, X AXIS 7160\SPCC103803582178A0工作台後飾板REAR PLATE,TABLE 7510\SPCC103903582177A0工作台前飾板FRONT PLATE, TABLE 7510\SPCC104003582065C0X軸分油座OIL DISTRIBUTOR BRACKET 7210\SPCC10410*******B0油分配器座(Y軸)DISTRIBUTOR BRACKET 7210\SPCC104204640028849塑鋼製鏈條式聯動管ELECTRICAL CONDUIT UNIT1台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F21028X軸傳動單元X AXIS TRANSMISSION UNITV42iW00103170053B0軸承隔環BEARING SPACER3230\SCM4100203170054B0前迷宮環座LAMINAL RING BRACKET3250\SCM4200303170057B0軸承隔環BEARING SPACER3230\SCM4100403170067A0預拉彈簧檔片PRELOAD SPRING STOPPER 3230\S45C100503170070A0Z軸尾端軸承座REAR BEARING HOUSING 1080\S45C100603560016B0軸承壓蓋BEARING CAP 3240\SCM4100703560017B0防撞膠塊RUBBER CUSHION 4370\請改下3560017C0200803560018G0防撞膠塊固定座RUBBER CUSHION BRACKET 3240\SCM4100903560019B0防撞膠固定座RUBBER CUSHION BRACKET 3230\S45C1010********F0Z軸尾端軸承座壓板PUSHING PLATE,BEARING HOUSI 3120\SCM4101103560132B0尾端座蓋板REAR BEARING HOUSING COVER 3180\SPCC101203581022B0尾端座(X軸)REAR BEARING HOUSING 1080\FC-25\3581022B2101303581027B0傳動座TRANSMISSION HOUSING1080\FC-25\3581027B2101403984063A0滾珠導螺桿(X軸)BALL SCREW9860\V42iW101504020401030鎖緊螺帽LOCK NUTMK30101604020403035鎖緊螺帽LOCK NUTMF35(M35xP1.5)101704050175012壓縮彈簧COMPRESSIVE SPRINGφ1.25Xφ7.5X12L801804061306828迷宮環LAMINAL RINGFK3-AS 62/2.8/0.82601904402030062螺桿軸承BALL SCREW BEARINGBS30M62/15-P4A.DUM102004402435072螺桿軸承BALL SCREW BEARINGBS35/72/15TUM1021********A0傳動座蓋板TRANSMISSION HOUSING COVER7180\SPCC1022********D0迷宮環座LAMINAL RING BRACKET3250\SCM4102304061300001迷宮環LAMINAL RING FK3-AS 68/2.8/0.82302404080508050斜梢SLIDE PIN#8x50L(附內牙)4台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F22024Y軸傳動單元Y AXIS TRANSMISSION UNITV42iW00103170053B0軸承隔環BEARING SPACER3230\SCM4100203170054B0前迷宮環座LAMINAL RING BRACKET3250\SCM4200303170057B0軸承隔環BEARING SPACER3230\SCM4100403170067A0預拉彈簧檔片PRELOAD SPRING STOPPER 3230\S45C100503170070A0Z軸尾端軸承座REAR BEARING HOUSING 1080\S45C100603560016B0軸承壓蓋BEARING CAP 3240\SCM4100703560018G0防撞膠塊固定座RUBBER CUSHION BRACKET 3240\SCM4100803560019B0防撞膠固定座RUBBER CUSHION BRACKET 3230\S45C100903560023F0Z軸尾端軸承座壓板PUSHING PLATE,BEARING HOUSI 3120\SCM41010********B0尾端座蓋板REAR BEARING HOUSING COVER 3180\SPCC101103560374A0防撞膠塊RUBBER CUSHION 4370\PU201203581022B0尾端座(X軸)REAR BEARING HOUSING 1080\FC-25\3581022B2101303581027B0傳動座TRANSMISSION HOUSING1080\FC-25\3581027B2101403984062A0滾珠導螺桿BALL SCREW9860\市購品4150H\Y軸101504020401030鎖緊螺帽LOCK NUTMK30101604020403035鎖緊螺帽LOCK NUTMF35(M35xP1.5)101704050175012壓縮彈簧COMPRESSIVE SPRINGφ1.25Xφ7.5X12L801804061306828迷宮環LAMINAL RINGFK3-AS 62/2.8/0.82601904402030062螺桿軸承BALL SCREW BEARINGBS30M62/15-P4A.DUM102004402435072螺桿軸承BALL SCREW BEARINGBS35/72/15TUM1021********A0傳動座蓋板TRANSMISSION HOUSING COVER7180\SPCC1022********D0迷宮環座LAMINAL RING BRACKET3250\SCM4102304061300001迷宮環LAMINAL RING FK3-AS 68/2.8/0.82302404080508050斜梢SLIDE PIN#8x50L(附內牙)4台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F23020Z軸傳動單元Z AXIS TRANSMISSION UNITV42iW00103170053B0軸承隔環BEARING SPACER3230\SCM4100203170054B0前迷宮環座LAMINAL RING BRACKET3250\SCM4200303170057B0軸承隔環BEARING SPACER3230\SCM4100403560022A0預拉彈簧擋片PRELOAD SPRING STOPPER 3230\S45C100503170070A0Z軸尾端軸承座REAR BEARING HOUSING 1080\S45C100603560016B0軸承壓蓋BEARING CAP 3240\SCM4100703560019B0防撞膠固定座RUBBER CUSHION BRACKET 3230\S45C200803560023F0Z軸尾端軸承座壓板PUSHING PLATE,BEARING HOUSI 3120\SCM4100903560132B0尾端座蓋板REAR BEARING HOUSING COVER 3180\SPCC1010********A0防撞膠塊RUBBER CUSHION 4370\PU201103581022B0尾端座(X軸)REAR BEARING HOUSING 1080\FC-25\3581022B2101203581027B0傳動座TRANSMISSION HOUSING 1080\FC-25\3581027B2101313984064A0滾珠螺桿(Z)Z AXIS BALL SCREW9860\市購品101404020401030鎖緊螺帽LOCK NUTMK30101504020403035鎖緊螺帽LOCK NUTMF35(M35xP1.5)101604050175012壓縮彈簧COMPRESSIVE SPRINGφ1.25Xφ7.5X12L801704061306828迷宮環LAMINAL RINGFK3-AS 62/2.8/0.82601804402030062螺桿軸承BALL SCREW BEARINGBS30M62/15-P4A.DUM101904402435072螺桿軸承BALL SCREW BEARINGBS35/72/15TUM1020********A0傳動座蓋板TRANSMISSION HOUSING COVER7180\SPCC1021********B0軸承隔環BEARING SPACER3230\SCM4102204020402035鎖緊螺帽LOCK NUTMR35(M35xP1.5)1 02304080508050斜梢SLIDE PIN#8x50L(附內牙)4英文品名2F50038外型護罩單元LOWER ENCLOSURE GUARD UNITV42iW00103582231A0大護罩LARGE COVER7500\SPCC100203582229A0左後護罩(L) REAR GUARD7500\SPCC100303582230A0右後護罩(R) REAR GUARD7500\SPCC100403582232A0左前門(L) FRONT DOOR 7480\SPCC100503582233A0右前門(R) FRONT DOOR 7480\SPCC100603582234A0前門側擋水板FRONT DOOR PLATE 7210\SPCC200703581295A0前門定位板ORIENTATION PLATE 7210\SPCC200803582236A0護罩前飾條RUBBER RIBBON, TELESCOPIC BA 4510\SUS 303100903582235A0下門軌LOWER DOOR GUIDE 7130\SPCC1010********A0前門下門輪支架LOWER DOOR WHEEL BRACKET 7110\SPCC401103520054C0門輪DOOR WHEEL 3260\S45C401203520055A0門輪DOOR WHEEL 3260\S45C401304060600028C型扣環(孔用)C TYPE RETAINER RINGR-28401404060700012C型扣環(軸用)C TYPE RETAINER RINGS-12401504400206001深槽滾珠軸承BEARING6001ZZ 12x28x8401604300460100管型把手(加高)HAHDLEU1-600L-100H201703560146B0前門壓克力ACRYLIC PLATE, FRONT DOOR4360\ACRY201803560169B0壓克力壓板LOCKING PLATE, DOOR ACRYLIC7120\SPCC201903582049A0上門輪座DOOR WHEEL BRACKET7110\SPCC202004402000628軸承BEARING628ZZ 8*24*8 日本12021********D0護罩壓克力SIDE DOOR ACRYLIC PLATE4360\ACRY2022********A0側門飾條RUBBER RIBBON4510\SUS303光面2023********B0側門把手座SIDE DOOR HANDLE BRACKET 7180\SPCC402404300401421把手 (染黑)HAHDLE A-42-A402504090500403鎖頭LOCK C-403(長型)七星小S402604720700081工作燈WORKING LIGHT HT-S81/24V 70W1027********A0工作燈座WORKING LIGHT BRACKET 7210\SPCC1028********A0右上蓋板RINGHT SIDE COVER 7510\SPCC1029********A0伸臂蓋板OUTSTRETCHED ARM COVER 7180\SPCC103003582238A0左後飾板REAR PLATE7510\SPCC1英文品名2F5003803103582239A0左後飾板支撐座BRACKET, REAR PLATE7180\SPCC103203582240A0右後飾板後蓋板BRACKET, REAR PLATE7180\SPCC103303582241A0油冷機門DOOR OF OIL COOLER7510\2t SPCC103404300421602門扣把手DOOR LOCKB-010長軸(六角型)+B-1602(取手103504300401024門扣把手檔板DOOR LOCK PLATE B-01024103603582242A0電器箱下飾板REAR BRACKET POWER CABINET 7450\10370*******A0右下飾板(R) LOWER PLATE 7510\SPCC103803582244A0前下飾板LOWER PLATE 7510\SPCC103903560696A0水槍座WATER GUN SEAT 7210\SPCC104003560697A0風槍座AIR GUN SEAT7210\SPCC1台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F51038水箱單元(螺旋式排屑)COOLANT TANK UNIT(COIL TYPEV42iW00103582228A0導屑槽(螺旋式)CHIP TRAUGH7520\SPCC100203582068B0螺旋捲屑器CHIP CONVEYOR9570100304440800015排屑器馬達CONVEYOR MOTOR1/4HP 1:100 FME22100403582069B0排屑炮管(附蓋及防漏膠墊)CHIP THROUGH TUBE 7570\SPCC100503582072E0水箱COOLANT TANK 7580\SPCC100603582073E0水箱蓋COOLANT TANK COVER 7510\SPCC100703582125A0過濾擋水板WATER BAFFLE 7210\SPCC100803582102B0蓄屑盤CHIP PLATE 7520\SPCC100903582103C0蓄屑槽FILTER NET 7590\SPCC1010********B0水箱遮水板DASH BOARD 7180\SPCC101103500428A0管接頭座CONNECTOR BRACKET 3150\S45C101204300401421把手 (染黑)HAHDLE A-42-A201304430040303切削液泵浦(直立式)COOLANT PUMPTPHK4T3-2S101404510100001油表COOLANT LEVEL GAUGE3''101504530012424水用電磁閥KSDSOLENOID VALVEJB4K-24V(1/2")2<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F52025電氣箱單元POWER CABINET UNITV42iW00103582207A0電氣箱POWER CABINET7450\SPCC100203582208A0電氣箱左門(L) DOOR, POWER CABINET7450\SPCC100303582209A0電氣箱右門(R) DOOR, POWER CABINET7450\SPCC100403582210A0電氣箱門調整組ADJUSTING SET FOR POWER CAB 7450\SPCC400503582211A0電氣箱支架BRACKET FOR POWER CABINET 7450\SPCC100603582220A0I/O基板(上)I/O BOARD(UPPER)7560\3t SPCCZ100703582221A0I/O基板(下)I/O BOARD(LOWER)7560\SPCCZ100803500149B0主電源開關座MAIN POWER SWITCH BRACKET 7160\SPCC100903500150C0左右調整座ADJUSTABLE BRACKET 7160\SPCC1010********A0電器箱聯動管支架CONDUIT BRACKET 7210\SPCC101103582219A0聯動管支架蓋板COVER FOR CONDUIT BRACKET 7210\SPCC101203582215A0電磁閥配置板VALVE BRACKET 7210\SPCC101304090500403鎖頭LOCKC-403(長型)七星小S301404560300010熱交換器HEAT EXCHANGERHPW-10AR/EA-2A1<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F53054操作箱單元 三菱-70MOPERATION CABINET UNITV42iW00103582222A0伸臂OUTSTRETCHED ARM7470\SPCC100203582223A0伸臂上蓋板(A)OUTSTRETCHED ARM COVER7180\SPCC100303582224A0伸臂上蓋板(B)OUTSTRETCHED ARM COVER7180\SPCC100403582225A0伸臂出線連結座OUTSTRETCHED ARM CONNECTING 7210\SPCC100503582226A0伸臂連結蓋板OUTSTRETCHED ARM CONNECTING 7180\SPCC100603582227A0伸臂側蓋板OUTSTRETCHED ARM COVER 7180\SPCC100703500129A0旋轉座ROTATION BRACKET 3240\S45C100803580264B0操作箱OPERATION CABINET 7460\SPCC100903560523B0操作箱後蓋CABINET REAR COVER 7460\SPCC1010********C0洩放電阻座(大)BLEEDER RESISTANCE BRACKET 7210\SPCC101103581310E0洩放電阻座蓋COVER,BLEEDER RESISTANCE BRA 7210\SPCC101204300400400管型把手(自然色)HAHDLE U1-400L101304720632243警示燈(三層)WARNING LIGHTGSL-24V-3-B1<結 束>台灣力得衛宇龍科技股份有限公司*單階材料用量清單製表日期: 101-03-30第1頁主件品號序號元件品號品 名英文品名規 格用量2F53055操作箱單元 Fanuc-0iMDOPERATION CABINET UNITV42iW00103582222A0伸臂OUTSTRETCHED ARM7470\SPCC100203582223A0伸臂上蓋板(A)OUTSTRETCHED ARM COVER7180\SPCC100303582224A0伸臂上蓋板(B)OUTSTRETCHED ARM COVER7180\SPCC100403582225A0伸臂出線連結座OUTSTRETCHED ARM CONNECTING 7210\SPCC100503582226A0伸臂連結蓋板OUTSTRETCHED ARM CONNECTING 7180\SPCC100603582227A0伸臂側蓋板OUTSTRETCHED ARM COVER 7180\SPCC100703500129A0旋轉座ROTATION BRACKET 3240\S45C100803500432E0操作箱(FANUC Oi MC)OPERATION CABINET 7460\SPCC100903500433C0操作箱後蓋CABINET REAR COVER 7460\SPCC101004300400400管型把手(自然色)HAHDLE U1-400L101104720632243警示燈(三層)WARNING LIGHTGSL-24V-3-B1<結 束>。

Dytran Instruments, Inc.21592 Marilla St. Chatsworth, CA 91311 Ph: 818-700-7818 Fax: 818-700-7880email:***************OG3093M32.docxREV A ECN 11436 12/29/14OPERATING GUIDEMODEL 3093M32 MINIATURE HIGH SENSITIVITYTRIAXIAL LIVM™ ACCELEROMETERWITH SINGLE 4-PIN CONNECTORINTERNALLY CASE GROUND ISOLATEDNOTE: LIVM™ is Dytran's trademark for its line of L ow I mpedance V oltage M ode sensors with built-in amplifiers operating from constant current sources over two wires. LIVM instruments are compatible with othermanufacturers’ comparable systems designated IEPE .OPERATING GUIDEMODEL 3093M32 TRIAXIAL ACCELEROMETER INTRODUCTIONModel 3093M32 is a miniature three-axis accelerometer using the latest in piezoceramic planar shear technology coupled with 2-wire internal LIVM (IEPE) electronics.This instrument contains three miniature piezoceramic planar shear mode accelerometer elements mounted to a single ground-isolated support and welded into titanium alloy housing. The three elements are mounted orthogonal to each other so that they can measure the complete motion of a point.Model 3093M32 is stud mounted into very small spaces since its vertical dimension is .59 in. It weighs only 10 grams.LIVM (IEPE) design means that three miniature charge amplifiers are built into the instrument, one for each axis, to lower the impedance of the piezoceramic elements by many orders of magnitude. This technique allows the driving of long cables without affecting sensitivity and the use of very simple constant current type power units.All elements are internally isolated from the outer case and are enclosed by a faraday shield for improved noise immunity.DESCRIPTIONRefer to the outline/installation drawing 127-3093M32 for the dimensions of Model 3093M32.The electrical connections from the charge amplifiers for each element are brought out to the contacts of a single four-pin connector mounted transversely to one vertical face of the housing. The three signal/power connections to the elements are connected to each of three pins while the three ground returns for the elements are tied together to one common pin of the four-pin connector. The case of this instrument is electrically isolated from electricalsignal/power ground.The performance specifications and criteria for Model 3093M32 are delineated on the specification sheet included with this operating guide.INSTALLATIONThis accelerometer is designed for stud mounting. If the accelerometer is mounted on any other surface, its calibration cannot be guaranteed.Select a smooth surface approx of 0.7 in. in diameter and clean off all oil, debris and any contaminants or foreign matter that would preclude a good coupling.The selected (or prepared) mounting area should be flat to within .001 in TIR for best high frequency response.NOTE: Before mounting, be sure to clean themounting surface thoroughly to avoid inclusionof machining chips and other debris betweenmating surfaces. Intimate contact betweenmating surfaces is important for bestperformance.If a fair amount of motion is expected during the test, it is good practice to tie the cable down to a stationary point as close as possible to the accelerometer (but not closer than 1 inch) to avoid potentially damaging cable whip.You are now ready to connect the 3093M32 to the power unit.OPERATIONThe Dytran power unit specifically designed to power the Model 3093M32 is the Model 4114B1. This line-powered unit has a 4-pin connector jack similar to that on the 3093M32. Cable Model 6811AXX connects the 3093M32 to the power unit. (‘XX’ is the cable length in feet)Connect the 6811XX cable to Model 3093M32 by first rotationally aligning the locating tab, then engaging the rotating threaded collar and threading the collar on, hand tight.Connect the other end of the cable to the 4-pin connector on the power unit and tighten threaded collar hand tight. As previously noted, tie cable down within 1 inch or so of the instrument if excessive displacement of the accelerometer is expected.Apply power to the power unit and allow several seconds for coupling capacitors to fully charge. Rotate the channel selector knob through the first three positions to monitor the bias voltage of each of the three accelerometer element assemblies to check for normal operation. The bias voltage level appears on the front panel mounted voltmeter on the 4114B1.Consult the paper, "Low Impedance Voltage Mode (LIVM) Theory and Operation", included as part of this manual, for instructions in using the bias monitoring voltmeter on the power unit as a check for normal operation and as an effective trouble shooting aid.Although only one axis of the 3093M32 may be monitored with the front panel meter on the4114B1, each axis is continuously outputting data at the respective output jack at all times. Selecting a channel for bias monitoring does not affect the signal from that channel.Connect each of the three BNC ‘Output’ jacks of the power unit to the readout instrument or data collector and proceed with the measurement. The sensitivities of each of the three axes are directly in mV/G and are specified precisely in the calibration certificate supplied with each instrument.Be sure to check the orientation of each axis with the markings on the instrument in theoutline/installation drawing supplied with the Operating Guide. The arrows indicate the direction of acceleration that will produce positive-going output signals. The vertical axis, axis 3, produces positive-going output voltage when the accelerometer is accelerated upward, i.e., away from the mounting surface.REMOVAL (OR UN-INSTALLATION)It is very important when removing this instrument to remember that, although it is built to be very rugged, it is a sensitive measuring instrument and as such should be treated gently when being removed from its installation. Never strike the unit to break it free from its mounting surface. Simply grip two opposing flats with an adjustable or open-end wrench and gently twist the instrument. This method avoids any trauma to the instrument and will help ensure a long life for the accelerometer.MAINTENANCE AND REPAIRThis instrument is not field repairable. No maintenance is required, or possible. If a problem occurs, contact the factory for help. You will be assigned a Returned Material Authorization (RMA) number should the instrument have to be returned to the factory for evaluation. A short note describing the problem will facilitate the repair procedure.There is no charge for evaluation of the instrument and we will perform no repair work until you are notified of any charges.It is good practice to return the instrument to the factory for recalibration from time to time with frequency of recalibration dependent on usage intensity and frequency.。

™Universal precision cable and pipe locatorDelivering fast, accurate, reliable and repeatable locate data. The RD8000™PDL and PXL are powerful multifunctional pipe and cable locators designed for use across the pipe and cable location industry. With several unique features, the RD8000™ delivers speed, accuracy and reliability, yet remains a cost-effective solution for any application. Designed with the latest digital architecture and software, RD8000™ delivers a highly accurate, controllable and reliable locate solution to service any industry, anywhere in the world.ErgonomicsThe RD8000 is ergonomically designed to deliver a superior performing locator that provides the user with a light weight, energy efficient and exceptionally well balanced tool. At only 1.9kg, the RD8000 is comfortable for extended periods of use. Despite its weight and form, the RD8000 retains the environmental durability associated with an IP54 rating, meaning you can operate it in almost any environment. The locatorand transmitter both feature large, high contrast, backlit LCD screens that provide the user with clear information in any light conditions. The intuitive and responsive user interface has easily identifiable icons that are consistent across the locator and transmitter range, ensuring straightforward operation. Centros™All RD8000 units are Centros™ enabled.Centros is a measurement engine based onmore than 30 years of continuous development,combining new and innovative algorithms with established software on a high-performance processor core. Centros improves location accuracy and repeatability and delivers timely responsiveness in the field.iLOC™iLOC™ is an advanced long range Bluetooth® link betweenthe RD8000 locator and transmitter that helps save the operator time and effort. iLOC allows the operator to control the transmitter remotely using a number of unique features. With iLOC you can spend less time walking and more time locating. iLOC™ operates at distances up to 300 meters (328 yards) line of sight providing an operator with a fast and unique means of conducting a survey.iLOC applications supported are:n SideStep™ – enables an operator to move the transmitter frequency slightly above the selected frequency enabling locates in areas prone to interference or where multiple operators are locating.n Frequency Select – choose an active frequency on the RD8000 and synchronously change the transmitterfrequency to match.n Power Management – an operator can adjust the output power of the transmitter to optimize output signal, leading to efficient use of transmitter batteries.n Transmitter remote sleep/wake– enter standby mode toprolong battery life.Conveniently wake thetransmitter with a simplekey press on thelocator. Transmittercan be set to standbymode each timepassive locationis carried out.SurveyCERT ™SurveyCERT ™ gives the operator the tools to pass survey information to third-party applications for audit, analysis and reporting. With the RD8000, the operator can store and review up to 1000 locate records. Upload this information to a PDA or PC using the RD8000 Bluetooth ® connection and you can instantly view the data using the SurveyCERT ™ graph program. If the PC/PDA has a GPS receiver, SurveyCERT ™ will automatically add the timestamp and position to the record. Built for interoperability, SurveyCERT ™ data is compatible with commercial Geographical Information System (GIS) pa ckage.eCAL™eCAL ™ is a novel Radiodetection technique that allows the operator to validate the original factory calibration of the RD8000. This means the operator has confidence that the locator continues to meet its factory calibration. eCAL ™ can issue and print a validation certificate without needing to return the RD8000 to a service center.TruDepth ™: gives the operator the confidence that the depthreading is accurate by only indicating a locate depth when the locator is correctly oriented directly above the pipe/cable.Dynamic Overload Protection: extends the RD8000operation into areas where other products fail. In electrically noisy environments, particularly in areas where very largesignals are present, it automatically filters out unwanted signals allowing the operator to work effectively in areas such as power substations and overhead railway HV cables.Peak/Null Mode: is a tool to identify the effects of fielddistortion due to ground conditions or nearby utilities. Simultaneous display of Peak bar graph response and proportional Null arrows allow a quick assessment of locate conditions.Strike Alert ™: reduces the risk of accidents by detectingshallow power cables and alerting the operator with an audio warning.Passive Avoidance: allows the operator to survey theground quickly using simultaneous detection of Power and Radio signals carried on underground pipes or cables. The RD8000 provides real audio to differentiate the relative proportions of Power and Radio signals present.Compass: Provides the operator with a visual indicationof the target cable or pipes direction. With this feature, the operator can easily follow the target line and then position the locator correctly to maximize depth accuracy.Fault Find: is a technique that enables an operator to locatea cable fault using an A frame attached to the Locator. On-screen arrows help show the fault’s direction and help the operator locate the fault accurately to within 1 meter (39 inches).CD (Current Direction): A method of identifying a targetcable amongst a number of parallel cables using CD direction arrows. With CD the operator can locate a target quickly and eliminate wasted time following faulty trails.The RD8000 represents the latest in electromagnetic locator technology. Designed to meet our customers’ needs, the RD8000 provides a highly controllable, intuitive, cost-effective and reliable solution for any application, building on the reputation that Radiodetection has for supplying highly accurate, reliable and robust location products.Splash-proof keypadHigh contrast LCD with auto-backlight operates from -20 to +60° Celsius(-4 to 140° F)High contrast LCD with auto-backlight operates from -20 to +60° Celsius (-4 to 140° F)High visibility reflectivesafety arrowsErgonomic, robust ABS shock resistant and water resistant plastic case ensuresreliable use in hostile environmentsErgonomicrobust ABS caseiLOC ™Stored data from RD8000 transferred by Bluetooth ® may be displayed on a PC or PDA using Radiodetection’s SurveyCERT ™ applicationBase tray for accessoriesSurveyCERT ™Powered by 8 x NiMH or alkaline LR20 (D-Cell) batteries,or optional rechargeable battery packThe RD8000PXL is the industry standard high performance cable and pipe locator. It has a broad range of active, passive and sonde frequencies as well as a number of unique user features supplied as standard.Radiodetection’s most advanced cable and pipe locator delivers a broader range of frequencies and sophisticated fault-finding capabilities. It has all the features of the RD8000PXL and a larger range of active and passive frequencies (including CATV and CPS) plus Current Direction (CD), and Fault Find (FF) modes.Based on a fully digital platform, the new family of Radiodetection transmitters support the entire range of Radiodetection RD7000 and RD8000 cable andpipe locators.The Tx-1 is a low power transmitter. The Tx-3 has a higher current and induction capability as well as Fault Find. The Tx-10 has the highest current capability with both Fault Find and CD modes as standard.All models feature a three-stage phase sensitive amplifier that delivers a ground-impedance compensated, constant current across its entire bandwidth in either direct connect, clamp or inductive mode. The transmitters use less power and are ergonomically designed to deliver superior performance in a new light-weight, well-balanced case.The transmitters are 10% lighter than the industry standard T10 yet each is IP54 rated to cope with demanding environmental conditions. Each model has a removable accessory tray and a weatherproof battery compartment. A large, high contrast, backlit LCD screen provides the user with clear information. The interface is intuitive and responsive, allowing the operator to access any feature with ease.SideStep auto ™: allows the transmitter to calculate the optimum frequency based on groundimpedance. The transmitter uses this information to optimize the active frequency. SideStep auto ™ helps to improve locate accuracy and extends battery life.All models are compatible with the complete range of RD7000 and RD8000 frequencies in both inductive and direct connect modes. The transmitters use 8 D-cell batteries and can be powered from a vehicle using a 12V cable plug (it is recommended that an approved Radiodetection isolation transformer is used).As an additional feature, each model has a multimeter function providing measurement of output voltage, line voltage, current, impedance and power.To support the extended RD8000 iLOC feature set, the Tx-3 and Tx-10 can be ordered with integrated iLOC.Large stethoscopeAccessories:CD stethoscope2" or 4" receiver clamp Live cable connectorHigh gain stethoscopePlug connectorCD receiver clamp2" or 4" transmitter clampCD transmitter clampSmall stethoscopeA-frameSubmersible DD AntennaHeadphonesIn good conditions.*RD8000 will locate to greater depths but with reduced accuracy.Trademarks and Notices.Our products are covered by the following intellectual property rights:The following are trademarks of Radiodetection:iLOC ™, TruDepth ™, SideStep ™, SideStep auto ™, SurveyCERT ™, RD7000™, RD8000™, Centros ™, eCAL ™.The Design of the RD7000, RD8000 and transmitters has been registered.The Design of the 4 chevrons has been registered.The Bluetooth word, mark and logos are registered trademarks ofBluetooth SIG, Inc. and any use of such trademarks by Radiodetection is under license. Microsoft, Windows Mobile are registered trademarks of Microsoft Corporation, all rights reserved.90/RD8000/ENG/04support and repairCopyright 2011 Radiodetection Ltd - SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation. SPX andRadiodetection are trademarks of Radiodetection Ltd. and SPX Corporation. Due to a policy of continued development, we reserve the right to alter or amend any published specification without notice. The Bluetooth word, mark and logos are registered trademarks of Bluetooth SIG, Inc. and any use of such trademarks by Radiodetection is under license. RD8000 is a Trademark of Radiodetection. This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection To see the full range of products and services provided by Radiodetection visit:Radiodetection is a proud member of the SPX group of companies, which provide technical products and service solutions worldwide.Radiodetection and its associated companies specialize in the design and manufacture of products for the location and maintenance of underground pipes and cables. Our aim is to be viewed as the supplier of choice of ‘high performance’ quality equipment using advanced product technologies. We are also committed to both design innovation and customer support.Radiodetection equipment users have easy access totechnical support. A call to your regional representative, or the Radiodetection head office, will put you in contact with our team of field-experienced technical experts.Radiodetection has a team of factory-trained service technicians and dedicated service facilities. Turnaround is fast, and costs are very competitive.Product training for youroperators and training personnel is available on your site, or at Radiodetection’s headquarters. Training is with qualified instructors and each trainee receives a certificate to confirm they have received the training.AmericaRadiodetection 154 Portland RoadBridgton, ME 04009, USA Tel: +1 (207) 647 9495Toll Free: +1 (877) 247 3797 Fax: +1 (207) 647 9496 Email:*******************Web: Pearpoint39-740 Garand Lane, Unit B Palm Desert, CA 92211, USA Tel: +1 800 688 8094 Tel: +1 760 343 7350 Fax: +1 760 343 7351Email:**************************Web: Radiodetection (Canada)344 Edgeley Boulevard, Unit 34 Concord, Ontario L4K 4B7, Canada Tel: +1 (905) 660 9995Toll Free: +1 (800) 665 7953 Fax: +1 (905) 660 9579 Email:*******************Web: EuropeRadiodetection Ltd (UK) Western DriveBristol BS14 0AF , UK Tel: +44 (0) 117 976 7776 Fax: +44 (0) 117 976 7775 Email:*******************Web: Radiodetection (France) 13 Grande Rue, 76220 Neuf Marché, France Tel: +33 (0) 232 8993 60 Fax: +33 (0) 235 9095 58 Email:*******************Web: Radiodetection (Benelux) Industriestraat 117041 GD ’s-Heerenberg, Netherlands Tel: +31 (0) 314 66 47 00 Fax: +31 (0) 314 66 41 30 Email:*******************Web: Radiodetection (Germany) Groendahlscher Weg 11846446 Emmerich am Rhein, Germany Tel: +49 (0) 28 51 92 37 20 Fax: +49 (0) 28 51 92 37 520 Email:*******************Web: Asia-PacificRadiodetection (Asia-Pacific) Room 708, CC Wu Building302-308 Hennessy Road, Wan Chai Hong Kong SAR, China Tel: +852 2110 8160 Fax: +852 2110 9681Email:*******************Web: Radiodetection (China)Hongfu Mansion, Room 61622 Zheng Ge Zhuang, Bei Qi Jia Town Chang Ping District Beijing 102209, China Tel: +86 (0) 10 8975 5540 Fax: +86 (0) 10 8975 5640 Email:*********************Web: Radiodetection (Australia) Unit H1, 101 Rookwood Road, Yagoona NSW 2199, Australia Tel: +61 (0) 2 9707 3222 Fax: +61 (0) 2 9707 3788 Email:*******************Web: 。

NTG-3Instruction ManualIntroductionThank you for your purchase of the NTG-3 precision broadcast-grade shotgun microphone.The NTG-3 is one of ’s most exciting microphones. It is the result of years of development by engineers, providing the professional broadcast and fi lm industries with an affordable yet uncompromising microphone.One of the key features of the NTG-3 is its ability to withstand adverse conditions. Using a technology known as RF bias the NTG-3 is almost completely resistant to moisture, making it the only option when recording in any demanding environments where condensation is an issue.In addition to its very low weight and anti-glare fi nish, the NTG-3 also features incredibly low self-noise. I’m confi dent that you won’t fi nd a similar microphone that is this quiet.When not in use you’ll be able to store the NTG-3 in the weather resistant aluminium anti-roll storage cylinder (standard with purchase), providing additional protection when traveling and storing the NTG-3.Please take the time to visit and register your microphone for a full ten year warranty.While there you can view studio/field tips and techniques, as well as browse the comprehensive range of accessories for the NTG-3 and other microphones.Peter FreedmanMicrophonesSydney, AustraliaSpecifi cations AcousticPrinciple:Line GradientDirectionalPattern:Super-CardioidFrequencyRange:40Hz - 20kHzOutputImpedence:25ΩSensitivity:-30dB ± 2dB(31.6mV/Pa)Equivalent Noise:13 dBAMaximumOutput:8.2dBuDynamic Range:117dB SPLMaximum SPL:130dB @ 1kHzSignal/Noise:81 dBPower Requirement:P48 phantom (44-52V min 5mA)OutputConnection:3-pin XLRNet Weight: 163g Dimensions:19mm x 255mmSpecifi cationsFrequency ResponsePolar ResponseAccessories0˚90˚270˚180˚-2.0-20.0 -10.0 0.0-2.0-4.0-6.0-8.0-10.0-12.0-14.0-16.0-18.0-20.0-22.0-24.0-25.0dB rel. 1V/Pa+5.0Frequency:500 Hz :1000 Hz :4000 Hz :–––d B r e 1 V /P a 20100 -10-20-3020Hz 100 1000 10 000 20 000RM5 - Stand mount WSNTG3 - Wind shield RCNTG3 - Weather resistantaluminium storage cylinderZP2 - Zip pouchFeatures• Designed to withstand adverseenvironmental conditions• 50% less self-noise than the majorityof shotgun mics• True Condenser (external RF biased)• Extremely low handling noise• High level of immunity toradio frequency interference• H igh sensitivity• Superior broadcast sound quality• Designed & manufactured in Australia• Full 10 year guarantee*Powering the NTG-3• T he NTG-3 requires power to operate. This needs to be supplied via a P48V phantom power supplywhich is available from most professional videocameras or mixing consoles.•I f the camera or console does not provide phantom power, then an external phantom power supply is needed.*Online product registration required.• We strongly suggest the use of high quality XLR cables, using the shortest cable length possible to ensure minimal noise interference between the microphone output and the camera/recorder input.• The NTG-3 features a custom designed XLR connector that is specially designed to reduce susceptibility to RF interference from devices such as cell phones.• When mounting the microphone in a mic stand or shock/suspension mount you must ensure that you do not block any of the slots on the side of the microphone (as illustrated below).Obstructing these slots will affect the sound quality and the polar pattern (directional qualities).• The NTG-3 is designed for operation within demanding environments, where the traditional condenser microphone would fail. However all due care should be taken to protect the microphone body itself from high levels of moisture or dust. For maximum protection please store the NTG-3 inthe supplied storage cylinder when not in use.Connecting the NTG-3Using the NTG-3• S hotgun microphones have a narrow ‘pick-up’ angle or polar response, and so can be used togreat effect with cameras for news gathering,wedding videos, sporting events or in anysituation where you want to focus on a particulararea of sound source without having your audiooverpowered by ambient noise.The pick-up pattern of the NTG-3 has beentailored to be slightly wider and therefore moredirectionally forgiving than comparable shotgunmicrophones on the market. This makes boompole and handheld operation much easier.• The NTG-3 is supplied with a foam windshield.T his windshield should be used wheneverrecording outdoors, as even an unexpected slight breeze can cause unwanted sound interference.• For maximum wind protection a more specialisedwind shield is recommended, such as theDeadCat, WS7 deluxe windshield, or theBlimp suspension windshield system.• The supplied weather resistant aluminium storage cylinder is designed to provide extremeenvironmental protection for your microphonewhen not in use, however it is not recommendedthat the cylinder be immersed in liquid. Damageto the microphone caused by water entering thestorage cylinder is not covered by the microphone warranty.Using the NTG-3WarrantyAll microphones are warranted for one year from date of purchase. You can extend that to a full ten years if you register online at .The warranty covers parts and labour that may be required to repair the microphone during the warranty period. The warranty excludes defects caused by normal wear and tear, modifi cation, shipping damage, or failure to use the microphone as per the instruction guide.If you experience any problem, or have any questions regarding your microphone, fi rst contact the dealer who sold it to you. If the microphone requires a factory authorised service, return will be organised by that dealer.We have an extensive distributor/dealer network, but if you have diffi culty getting the advice or assistanceyou require, do not hesitate to contact us directly.MicrophonesInternational107 Carnarvon StreetSilverwater NSW 2128 AustraliaPh: +61 2 9648 5855Fax: +61 2 9648 2455USAP.O. Box 4189Santa Barbara, CA 93140-4189Ph: 805 566 7777Fax: 805 566 0071Technical SupportFor information and technical support questions contact:*******************In the Unites States and Puerto Rico, contact**************************************InAustralia,**********************************(02)96485855 Anywhere except Australia, the United States and Puerto Rico,********************************+61296485855。