下载文档原格式
技术资料ＴＩ２４６Ｃ／０７／ｚｈ／ｖ１．０用于高温消毒场合的溶解氧分析仪ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ／２５３Ｆ溶氧变送器ＬｉｑｕｉｓｙｓＭ．ＣＯＭ２２３Ｆ／２５３Ｆ的模块化设计可以满足客户的不同需求还可安装其它软件和硬件来实现特殊应用应用场合特点及优点基本单元可扩展至各种需要高温消毒的溶解氧测量场合培养基中溶氧控制有现场安装型或盘面安装型在溶氧量ｍｇ／ｌ与饱和度％ＳＡＴ之间可切换菜单结构完整宽大的两行液晶屏在空气或含氧介质中可进行简单的单点标定性能可靠可直接进行手工操作触点Ｐ（ＩＤ）控制器化学清洗完整清洗系统附加功能传感器在线检测报警或超限时ＨＡＲＴ或ＰＲＯＦＩＢＵＳ－ＰＡ／－ＤＰＬｉｑｕｉｓｙｓＭＣＯＭ２５３ＦＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ详细说明基本设置（ＨＸ）包括可同时显示也可根据需要隐藏可单点标定根据应用及操作ＬｉｑｕｉｓｙｓＭ２２３Ｆ／２５３Ｆ可以对进行设置这样可以隐藏那些不必要的报警信息直接可以快速控制限位开关也可根据需要液晶显示屏根据需要可显示设备及模块的及订购码带有氧气的吸收不仅与海拔有关可以抵削这些波动比如控制应用中的错误可被控制器监视检测出来最大允许时间间隔及超出及未超出的参考值有两个安全功能这可能由于过程阻塞断开及其它原因所至需显示大的量程范围又要取得良好的测量效果电流输出双线性准对数基本设置及附加功能测量系统一个溶氧变送器ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ或ＣＯＭ２５３Ｆ一套浸入式安装例如一根延伸电缆（ＣＹＫ７１型）带变送器ＬｉｑｕｉｓｙｓＭＣＯＭ２Ｘ３Ｆ的完整的测量系统１．溶氧探头ＯｘｙＨａｘＨＣＯＳ２１２．可伸缩组件ＣｌｅａｎＦｉｔＨＣＰＡ４７５３．测量电缆ＣＯＫ２１４．现场仪表ＬｉｑｕｉｓｙｓＭＣＯＭ２５３Ｆ５．面板安装仪表ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ电气连接盘面安装ＣＯＭ２２３Ｆ的电线接到背面的端子板上传感器置于外槽中）即使更换所有模块变送器也可以保持连线重排端子或重新接线ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ背面接线右尺寸ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ尺寸ＬｉｑｕｉｓｙｓＭＣＯＭ２５３Ｆ尺寸安装ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ安装ＬｉｑｕｉｓｙｓＭＣＯＭ２５３Ｆ盘面安装设备用所提供的捆绑螺丝来固定附件附在方形立柱上用螺丝固定在墙上户外操作须采用遮阳罩ＣＹＹ１０１安装在方形立柱上（通用形垂直立柱ＣＹＹ１０２或悬挂或安装支架ＣＹＨ１０１）将设备背面安装于遮阳罩上约面板外壳安装安装ＬｉｑｕｉｓｙｓＭＣＯＭ２５３Ｆ（续）圆柱安装套件（水平或垂直安装见）圆管安装（右图带遮阳罩）墙装螺丝６ｍｍ套管８ｍｍ技术数据输入输入一般数据制造商仪表型号被测参数与传感器ＣＯＳ２１配合进行溶氧测量显示和测量范围温度补偿范围压力补偿范围海拔调整范围盐度调整范围溶氧信号输入（２０，１０１３ｈＰａ）信号电流标准斜率传感器置于空气中感性负载开关电流感性负载开关功率温度０．１．．．２０ｍｇ／ｌ０．．．２００％ＳＡＴ０．．．５０５００．．．１１００ｈＰａ０．．．４０００ｍ０．．．４．０％或１０．．．５０Ｖ１０ｍＡ最大０／４．．．２０ｍＡ，，２．４／２２ｍＡ电气隔离误差电流最大５００７００ｄｉｇｉｔｓ／ｍＡ０．２．．．２０ｍｇ／ｌ２０．．．２００％ＳＡＴ．３５０Ｖ／５００ＶＤＣＥＮ６１０００－４－５１９９５ｒｍｓ０／４．．．２０ｍＡ５００７００ｄｉｇｉｔｓ／ｍＡ７．．．７０３５０Ｖ／５００ＶＤＣＥＮ６１０００－４－５１９９５电气隔离最大ｒｍｓ１５Ｖ０．６Ｖ１０ｍＡ最大２Ａ２Ａ２５０ＶＡＣ３０ＶＤＣ５００ＶＡＡＣ６０ＶＤＣ５００ＶＡＡＣ６０ＶＤＣ０．．．２０ｍｇ／ｌ，０．．．２００％ＳＡＴ０．．．７２００ｓ技术数据（续）精度控制器（）ＫＴＴ功能可调控制器响应控制器增益积分时间微调作用时间脉冲长度控制器时间脉冲频率控制器频率ｐｎｖ报警（）＂＂＂＂功能可转换报警阈值调整范围报警延迟最小越限监测暂停最大越限监测暂停用ＣＯＳ２１测量溶氧测量值分辨率测量误差显示重复性溶氧测量误差信号输出１１用ＣＯＳ２１测量温度测量值分辨率测量误差显示温度测量误差显示１１环境温度正常工作条件环境温度极限工作条件运输存储温度相对湿度正常工作条件面板安装设备防护等级现场外壳防护等级电磁兼容性（）（）（）盘面安装设备尺寸高深安装深度现场设备外壳尺寸高深盘面安装设备重量现场设备重量测量值显示（）（）材料盘面安装设备外壳面板薄膜现场设备电压功耗熔丝保护符合在标准工况下ＩＥＣ７４６－１１脉冲长度脉冲频率控制器最大测量范围最大测量范围－１０．．．＋５５－２０．．．６０－２５．．．＋６５１０．．．９５％ＩＰ５４（）ＩＰ３０（）ＩＰ６５ＥＮ６１３２６－１１９９７／Ａ１１９９８无冷凝前面二行带状态显示聚碳酸酯聚酯时间延迟环境条件结构数据电源传感器接线附件设备升级５１５０５８５７５１５０５８７０１０ｍ订购码延伸电缆ＣＹＫ７１用于溶氧传感器５００８５３３３５０００３９８７（请在订单中提供仪表序列号）５１５０６４６９５１５００９６３５１５００３２０５１５００３２１ＣＯＳ用于ＣＯＳ２１的测量电缆ＣＯＫ２１安装附件套件用于户外现场设备尺寸（高深）３００不锈钢ＳＳ３０４订购码通用立柱ＣＹＹ１０２方形管用于现场设备尺寸（高深）１４９５６０ｍｍ材料ＣＹＹ１０２－Ａ５１５０７２５４带ＥＨＥＤＧ及３Ａ认证５００７６８７８附件仪表选型ＬｉｑｕｉｓｙｓＭＣＯＭ２２３Ｆ／ＣＯＭ２５３Ｆ版本ＨＸＨＳ带传感器ＣＯＳ２１溶氧测量（基本功能）带传感器ＣＯＳ２１溶氧测量（扩展功能）供电电源０１２３５７８供电电源２３０ＶＡＣ供电电源１１５ＶＡＣ供电电源２３０ＶＡＣＣＳＡＧｅｎ．Ｐｕｒｐ供电电源１００ＶＡＣ供电电源２４ＶＡＣ特点和优点制药业传感器（不锈钢ＡＩＳＩ３１６Ｌ）２分钟）标准过程连接Ｐｇ１３．５耐高温１３０一体化温度传感器如发酵罐酶产品的过程控制化学生物制品技术资料ＴＩ２４４ｃ／０７／ｚｈ／ｖ１．０可高温消毒溶氧探头ＯｘｙＭａｘＨＣＯＳ２１高压消毒环境下长期稳定的探头装置结构功能系统的组成溶氧探头测量电缆ＣＯＫ２１可选过程配件功能和系统设计测量原理被测介质中的溶解氧透入膜其它溶解于液相中的物质如离子无法通过膜当传感器与变送器相连电极的电流结果在变送器上显示然后会下降仪器在无氧介质中的测量电流是０ｍＡ出现在阴极上的氧分子就还原成为氢氧根离子（ＯＨ），银在阳极被氧化成为银离子（Ａｇ）从阴极到阳极的电流与介质中的氧量成正比最终在显示器上ｍｇ／ｌ或％ＳＡＴ的溶氧浓度单位表示溶氧传感器２１２特殊测量电缆ＣＯＫ２１４ＣＯＳ２１的安装提示如下传感器的安装位置不要与垂直方向大于８０不要倒装在过程装配中调节极化过的和标定过的传感器在限定的应用范围内使用传感器安装指导在配件的操作指导中提示尺寸轴直径或１２ｍｍ１２０ｍｍ３５０ｍｍ１．Ｐｇ１３．５（）２．３．４．５．６．７．８．９．铠装电线密封圈密封圈阴极保护帽膜膜护帽阳极插头密封圈安装标定前的准备出现下列情况初次设定清洗银阳极不正常的时间间隔将探头置于空气中因此传感器的安装地点离水平面越近越好避免与水面的直接接触将传感器和变速器相连极化会自动开始若用其它变速器需加－６７０最后保持在一个稳定值时也可在水饱和空气中标定描述如下将极化的外部干燥的传感器置于水附近（参考＂标定前的准备＂部分）描述如下接线端Ｓ１２９０９１１１外导体激活的内导体（ＮＴＣ温度传感器）阴极阳极ＮＴＣ温度传感器接线图表在变送器的操作指导中分配绿／黄黄白棕蓝标定提示维护检查传感器定期检查传感器步骤如下检查标定值液化的传感器小时内的测量变量必须小于在这种情况下更换电解液或膜若反应时间太长或测量电流太低若问题仍存在参考下面的指导若问题持续存在在这种情况下订货号一手拿布转次小心晾干避免挤压玻璃电极（１００％ＳＡＴ＂＂）（８）１２％ＳＡＴ（）（５１５０５８７４）１０－２０提示电解液和膜的更换更换电解液和膜的过程如下服务工具箱垂直握住传感器的插座头用软布小心擦干玻璃电极若损坏用吸液管向新膜帽中注入的电解液订货号小心拧开玻璃棒上的膜帽避免皮肤避免化学试剂灼伤（５１５０５８７４）Ｏ１．５ｍｌ（５１０５０５８７３）注意流量符合灵敏度最小测量值的环境周围环境范围－１０．．．６０测量温度０．．．５０提示！决不允许探头变干０．．．１３００．．．４ｂａｒ当对高压消毒时现场消毒时需用非插入式探头若水渗入电缆插头从而避免腐蚀和可能导致的故障过程消毒ＣＯＳ２１极化电压极化时间长期飘移介质温度的影响介质压力的影响反应时间ｔ残余电流内部氧补偿９０－６７０稳定条件３００．１％／星期测量范围飘移下下从空气到氮气０．１％的电流２５安装角度与竖直方向不要超过８０订货信息膜套电解液Ｏ零点标定溶液电缆消毒附件配件２工具箱包含３个膜套更换用电解液和清洁布５１５０５８７４５０ｍｌ／瓶订货号５０００１０４１电缆插头的保护帽５１５０５８７２ＣｌｅａｎＦｉｔＨＣＰＡ４７５ＵｎｉＦｉｔＨＣＰＡ４４２（１２０ｍｍ）ＰｒｏＦｉｔＨＣＰＡ４６５订附件前ＣＯＫ２１．３Ｍ５１５０５８７０ＣＯＫ２１．５Ｍ５１５０５８６９ＣＯＫ２１．６Ｍ５１５０５８６８附件资料５１５０５９４０）ＴＩ２４０Ｃ／０７／ｅｎ（订货号ＵｎｉｔＦｉｔＨＣＰＡ４４２技术信息５１５０６７２４）ＴＩ１４６Ｃ／０７／ｅｎ（订货号ＴＩ２４６Ｃ／０７／ｚｈ（０２８）５２５５３９０５２５６００５传真６１００４１Ｅ－ｍａｉｌ：ｅｈｃｄ＠ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍ上海销售中心上海市田林路３８８号新业大楼８层电话：（０２１）５４９０２３００传真：（０２１）５４９０２３０２邮编：２００２３３Ｅ－ｍａｉｌ：ｅｈｓｈ＠ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍ北京销售中心北京市朝阳区朝外大街２２号泛利大厦７层１０号电话：（０１０）６５８８２４６８传真：（０１０）６５８８１７２５邮编：１０００２０Ｅ－ｍａｉｌ：ｅｈｂｊ＠ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍｗｗｗ．ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍ吉达公司（吉林独家代理）长春市同志街６４号火炬大厦１４０５室电话（０４３１）５６７１４２５邮编（０２４）２２７９１４９５传真１１００１３Ｅ－ｍａｉｌ：ｅｈｓｙ＠ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍ济南办事处济南市泺源大街６８号玉泉森信大酒店Ｂ座九楼９０１室电话（０５３１）６１１０５８４邮编（０２７）８８８６５６４０传真４３００６１Ｅ－ｍａｉｌ：ｅｈｗｈ＠ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍ康德公司（云南独家代理）昆明市东风东路９６号茶花宾馆２号楼电话（０８７１）３１４８６２２邮编（０９９１）３８２５６７６传真８３００１１Ｅ－ｍａｉｌ：ｎｅｏａｕｔｏ＠ｃｎ．ｅｎｄｒｅｓｓ．ｃｏｍ。
E+H压力变送器|E+H流量计|德国E+H一、供应E+H物位仪表：1、E+H雷达物位仪表:非接触式测量。
适用于各种恶劣工况(例如有毒高侵蚀性)，且不受被测介质物理特性变化影响的外部测量。
型号有：FMR230,FMR231，FMR240，FMR244，FMR245,FMR250，FMR530，FMR531，FMR532，FMR533。
2、E+H导波雷达物位仪表：接触式测量。
与被测介质的物理特性变化无关。
耐温达150度，耐压达40bar。
型号有：FMP40,FMP41C,FMP45。
3、E+H超声波物位计:非接触式测量。
适合各种液体和固体，同样包括侵蚀性介质及变介电常数介质。
耐温达150度，耐压达3bar。
型号有：FMU230/231,FDU91,FDU92,FDU93,FDU95,FDU96,FMU40/41,FMU42,FMU43。
FMU860/FMU861/FMU862,FDU80/FDU81/FDU82***。
4、E+H液体音叉开关：无需标定和维护。
适用于所有液体，亦适用于粘结、搅拌及含气泡的介质，与被测介质的介电常数无关。
耐温达150度，耐压达64bar.型号有:FTL50,FTL51,FTL51C,FTL50H,FTL51H,FTL70,FTL71.FTL20,FTL260。
5、E+H固体音叉开关：无需标定和维护。
适用于颗粒直径小于10mm的颗粒及粉尘，耐温高达150度，耐压达16bar。
型号有：FTM50,FTM51,FTM52,FTM30/31/32(D/S),FTM20/21,FTM2606、E+H静压式物位计：智能化压力传感，适用于液体、浆料、泥浆，与泡沫及介电常数无关。
耐温高达100度，耐压达4bar。
型号有：DB50,DB50L,DB51,DB52,DB53，FMX167，FMX165，FTC51，FTC52，FTC53。
7、E+H电容式物位计及开关：适合于各种液体，同样适用于侵蚀性介质和粘结介质。
前言CCM通用前置机平台是针对在电力等工业自动化控制领域中，通讯的方式多种多样、规约众多、集成组态方式复杂的状况开发出来的一套规约综合开发／运行／通讯平台。
其基于WindowsNT/2000平台，具有规约开发、规约调试、数据存储区查看、转发表、通讯测试、遥控闭锁、规约库、通讯组态等多方面的功能。
具有较强的运行稳定性和可靠性、直观的设置方式和较大的库存储及规约存储空间。
软件在微软的Visual C++5.0下开发，规约开发也在Visual C++5.0下进行，用Visual C++6.0读一下工程文件可以方便地转化成Visual C++ 6.0的工程文件，可以保持编译器版本的向下兼容。
软件具有友好的规约开发接口，提供了大量的接口函数帮助规约开发人员较规范地得到和实现各种软件所提供的各种功能，规约开发人员可以籍此开发各种简单和复杂的通讯规约。
在规约开发完毕后可以立刻进行组态并运行。
软件同时具有友好的组态设置界面，可以通过组态可视化地实现各种通信设置，这就大大方便了规约的开发和调试，特别是现场调试。
该软件的推出，可以使工业控制中通信规约的开发进一步规范化、形成规约库后可以使开发和工程调试相对分开，现场调试人员只须搞清通信规约种类、通信介质类型和用户对信道的要求即可进行灵活组态，大大减轻现场通信调试人员的工作负担和复杂程度。
概述1.1 CCM前置机应用总述CCM通用前置机平台是针对在电力等工业自动化控制领域中，通讯的方式多种多样、规约众多、集成组态方式复杂的状况开发出来的一套规约综合开发／运行／通讯平台。
其基于WindowsNT/2000平台，具有规约开发、规约调试、数据存储区查看、转发表、通讯测试、遥控闭锁、规约库、通讯组态等多方面的功能。
具有较强的运行稳定性和可靠性、直观的设置方式和较大的库存储及规约存储空间。
软件在微软的Visual C++5.0下开发，规约开发也在Visual C++5.0下进行，用Visual C++6.0读一下工程文件可以方便地转化成Visual C++ 6.0的工程文件，可以保持编译器版本的向下兼容。
５．５．４化学清洗功能
就像定时器功能化学清洗也能被
定义执行一个清洗周期
然而化学清洗支持不同的清洗和冲洗的间隔时间因而具有不同重复周期的不规则的清洗是可能的而且带有后冲洗时间的清洗时间也能被单独地定义
５．５继电器触点的组态
化学清洗功能只能使用Ｒｅｌａｙ３和４清洗进程中止总是伴随一个后冲洗时间当Ｅｃｏｎｏｍｙ被选择清洗只能用水
注
liquisys S
OPM 223 /253pH/ORP Ҿ
继电器控制参数设置说明
最大值触点（复位点
或最小值触点（复位点翻转点）
功能
当报警的阈值被超过
个报警（注意报警延时）
表配备了附加包裹时
继电器（翻转值复位值）
值继电器（翻转值
一旦产生偏差（正或负偏
每次ｈｏｌｄ将会把积分设定成０
ｈｏｌｄ可以在Ｓ２中被取消但
脉冲长度用于电磁阀
了脉冲长度
频率的时候当选择了脉冲长度则
的（例如周。
技术资料TI194C/07/en/04.0451500277 Liquisys M CPM223 / 253pH/ORP测量变送器配套模拟传感器、数字传感器和 ISFET 传感器的 pH 测量仪表模块化设计的Liquisys M CPM223/253 变送器容易适应用户各种不同的要求。
在“测量和发出警报”的基本型式开始，变送器能为特殊应用配套附加软件和硬件模块。
这些模块还能够根据需要更新。
应用污水处理中和解毒（电镀工业）水净化水质监控优点• 有现场和盘装两种外壳• 通用• 操作简单- 逻辑排列的菜单结构- 大尺寸两行显示器- 两点校准，非常简单• 工作安全- 过压（雷击）保护- 直接手动控制- 刻度真实性检查- 用户规定的报警配置基本单元能够用下列模块扩展：• 附加的2个或4个触点，用于：- 极限触点（也用于温度）- PID) 控制器- 简单清洗过程的定时器- 清洗包括化学清洗- 电流输入• 附加组件：- 用户定义的电流输出特性- 报警和超限触发的自动清洗- pH 玻璃和参比传感器的检验系统- 传感器寿命探测- 专用的中和控制器• HART ® 或 PROFIBUS-PA/-DP• 温度、pH/ORP 或连续控制器的次级电流输出Liquisys M CPM 223/253功能与系统设计基型仪表的特点pH 和 ORP 值测量通过菜单选择。
测量时，被测值能够显示为其它测量模式（例如pH - mV 或ORP % - ORPmV）。
温度在同一时间显示或者完全不显示。
校准PH 电极通常在同一个 pH 值校准。
因此，变送器当前的整定值是由上次校准决定，此整定值即作为下次校准的默认值。
如果缓冲溶液被偶然互换（例如首先是 pH 4 缓冲液，然后第一次用 pH 7 缓冲液代替 pH 7，然后是 pH 4），真实性检查仍保证校准得到承认。
配置需要的不同报警取决于应用和操作的人员。
因此，变送器允许每个不同的故障与报警触点和故障电流的配置无关。
Products Solutions Services TI00200C/07/EN/14.1371235717Technical InformationLiquisys M CUM223/253Turbidity and suspended solids transmitterApplication•Sewage treatment plants, suspended solids measurement•Wastewater treatment•Water treatment and drinking water monitoring•Surface water: rivers, lakes, ocean•Service waterYour benefits•Field or panel-mounted housing•Universal application–One instrument for turbidity and suspended solids–Units: FNU (formazine standard), ppm, g/l, % or % SS•Simple handling–Logically arranged menu structure–Ultrasimple calibration with user samples and alarm signalling for calibrationerrors•Safe operation–Overvoltage (lightning) protection–Manual contact control and user-defined alarm configuration–Automatic sensor self-recognition with calibration data transferThe basic unit can be extended with:•2 or 4 additional contacts for use as:–Limit contacts (also for temperature)–P(ID) controller–Timer for simple rinse processes–Complete cleaning with Chemoclean•Plus package:–Any current output configuration via table–Automatic cleaning start–Display in customer units (e.g. density) via table assignment–Live check of sensor•HART or PROFIBUS PA / DP•2nd current output for temperature, main measured value or actuating variable•Current input for flow rate monitoring with controller shut off or for feedforwardcontrolLiquisys M CUM223/2532Endress+HauserFunction and system designFeatures of the basic versionMeasurement of turbidity and suspended solidsThe sensor is selected from the menu. During measurement, the value measured can be displayed in the other measuring mode. The temperature is displayed at the same time if desired.ConfigurationDifferent alarms are required depending on application and operator. Therefore the transmitterpermits independent configuration of the alarm contact and error current for each individual error. Unnecessary or undesirable alarms can be suppressed in this manner. Up to four contacts Up to two contacts can be used as limit contacts (also for temperature), to implement a P(ID) controller or for cleaning functions.Direct manual operation of the contacts (bypassing the menu) provides quick access to limit, control or cleaning contacts, permitting speedy correction of deviations.The serial numbers of the instrument and modules and the order code can be called up on the display.Additional functions of the Plus package TSCurrent output configurationIn order to output wide measuring ranges while still achieving a high resolution in specific ranges, the current output can be configured as required via a table. This permits bilinear or quasi-logarithmic curves, etc.Process Check System (PCS)It comprises two independent safety functions:•Errors in applications without control are detected by monitoring the limit between plausible and implausible measured values, i.e. the alarm threshold .•Errors in applications with control are detected by the controller monitor which monitors freely adjustable, maximum permissible time intervals and reference value overshoot or undershoot.Live checkThe live check issues an alarm when the sensor signal does not change over a defined period of time. This may be caused by blocking, passivation, separation from the process, etc.Additional functions of version TSDisplay of various measurement unitsIn addition to turbidity (FNU, NTU) and concentration (ppm / % SS), the display can also show other units (e.g. density). A table is used for conversion (calibration in %).Second current outputThe second current output can be configured for temperature, main measured value (turbidity, suspended solids) or actuating variable.Current inputThe current input of the transmitter allows two different applications: controller shut-down in case of lower flow rate violation or total failure in the main flow as well as feedforward control. Both functions are also combinable.Liquisys M CUM223/253Endress+Hauser 3Measuring systemA complete measuring systems comprises:•The transmitter Liquisys M CUM223 or CUM253•A sensor with or without an integrated temperature sensor •An immersion, flow or retractable assemblyOptions: extension cable CYK81, junction box VBM or RM123Immersion assembly CYA611Retractable assembly CUA451Assembly with gas bubble trap45Liquisys CUM253Liquisys CUM223Liquisys M CUM223/2534Endress+HauserInputMeasured variables Turbidity, suspended solids, temperature Measuring rangeCable specificationSignal inputDigital communication Temperature measurement NTC 30 k Ω at 25 °C (77 °F)Binary inputsCurrent input4to 20mA, galvanically separated Load: 260Ω at 20mA (voltage drop 5.2V)CUS31:0.000 to 9999 FNU/NTU 0.00 to 3000 ppm 0.0 to 3.0 g/l 0.0 to 200.0 %CUS41:0.00 to 9999 FNU/NTU 0.00 to 9999 ppm 0.0 to 300.0 g/l 0.0 to 200.0 %Temperature:-5.0 to +70.0 °C (+23 to +158 °F)Cable length:max. 200 m (656 ft.)Voltage:10to 50V Power consumption:max. 10mALiquisys M CUM223/253Endress+Hauser 5OutputOutput signal0/4 to 20 mA, galvanically separated, activeSignal on alarm 2.4 or 22 mA in case of an error Loadmaximum 500 Ω Transmission rangeResolution max. 700 digits/mA Isolation voltage max. 350 V RMS /500 V DC Overvoltage protection according to EN 61000-4-5Auxiliary voltage outputContact outputsLimit contactorHART Signal coding Frequency Shift Keying (FSK) + 0.5 mA via current output signal Data transfer rate 1200 Baud Galvanic isolationyesPROFIBUS PA Signal coding Manchester Bus Powered (MBP)Data transfer rate 31.25 kBit/s, voltage mode Galvanic isolationyes (IO-Module)PROFIBUS DP Signal coding RS485Data transfer rate 9.6 kBd, 19.2 kBd, 93.75 kBd, 187.5 kBd, 500 kBd, 1.5 MBd Galvanic isolationyes (IO-Module)CUS31/CUS41:adjustable, min. ∆ 0.1 FNU, ∆ 0.1 ppm, ∆ 0.1 g/l, ∆ 0.1 %Temperature:adjustable, ∆ 10to ∆ 100 % of measuring rangeOutput voltage:15V ± 0.6Output current:max. 10mA Switching current with ohmic load (cos ϕ= 1):max. 2A Switching current with inductive load (cos ϕ = 0.4):max. 2ASwitching voltage:max. 250V AC, 30V DC Switching power with ohmic load (cos ϕ = 1):max. 500 VA AC, 60W DC Switching power with inductive load (cos ϕ = 0.4):max. 500VA AC, 60W DC Pickup/dropout delay:0to 2000sLiquisys M CUM223/2536Endress+HauserControllerAlarmFunction (adjustable):pulse length/pulse frequency controller Controller response:PIDControl gain K p :0.01to 20.00Integral action time T n :0.0to 999.9min Derivative action time T v :0.0to 999.9min Period for pulse length controller:0.5to 999.9 s Frequency for pulse frequency controller:60to 180 min -1Basic load:0to 40% of max. set valueFunction (selectable):Latching /momentary contactAlarm threshold adjustment range:Turbidity / suspended solids / temperature: complete measuring range Alarm delay:0to 2000s 0 to 2000 minLiquisys M CUM223/253Protocol specific data HARTManufacturer ID11hDevice type code0095hTransmitter specific revision0001hHART specification 5.0DD files /hartLoad HART250Device variables None (dynamic variables PV, SV, only)Features supported-PROFIBUS PAManufacturer ID11hIdent number1517hDevice revision11hProfile version 2.0GSD files /profibusGSD file versionOutput values Main value, temperature valueInput values Display value of PLCFeatures supported Device locking: The device can be locked by hardware orsoftware.PROFIBUS DPManufacturer ID11hIdent number151F hProfile version 2.0GSD files /profibusGSD file versionOutput values Main value, temperature valueInput values Display value of PLCFeatures supported Device locking: The device can be locked by hardware orsoftware.Endress+Hauser7Liquisys M CUM223/2538Endress+HauserPower supplyElectrical connectionThe device is approved for protection class II and is generally operated without a protective ground connection.The circuits "C" and "F" are not galvanically isolated from each other.Electrical connection of the transmitterA B C DE F G SensorSignal output 1 turbidity/solids content Signal output 2 temperature Binary input 1 (Hold)Binary input 2 (Chemoclean)Aux. voltage outputAlarm (current-free contact position)H I J K L M Relay 1 (current-free contact position)Relay 2 (current-free contact position)Relay 3 (current-free contact position)Relay 4 (current-free contact position)Current input 4to 20mA Power supplyLiquisys M CUM223/253Endress+Hauser 9Sensor cableThe sensors are delivered with measuring cables. Use a junction box and an extension cable to extend the measuring cable (see "Accessories")Connection of the turbidity sensors CUS31 and CUS41Supply voltageDepending on ordered version:100/115/230 V AC +10/-15 %, 48 to 62 Hz 24 V AC/DC +20/-15 %Fieldbus connectionHART Supply voltagen/a, active current outputs Integrated reverse voltage protectionn/a, active current outputsPROFIBUS PA Supply voltage 9 V to 32 V, max. 35 V Polarity sensitiveno FISCO/FNICO compliant acc. to IEC 60079-27noPROFIBUS DP Supply voltage 9 V to 32 V, max. 35 V Polarity sensitiven/a FISCO/FNICO compliant acc. to IEC 60079-27noLiquisys M CUM223/25310Endress+HauserPower consumption max. 7.5 VAMains protection Fine-wire fuse, medium-slow blow 250 V/3.15 ACircuit breakerThe device does not have a power switch‣You must provide a protected circuit breaker in the vicinity of the device.‣This must be a switch or a power-circuit breaker and you must label it as the circuit breaker for thedevice.‣At the supply point, the power supply for the 24 V versions must be isolated from dangerous livecables by double or reinforced insulation.Performance characteristicsMeasured value resolutionMaximum measured error 1)Repeatability 2)± 1% of measured value (min. 0.01 FNU)CUS31:0.001 FNU/NTU, 0.01 ppm, 0.01 g/l, 0.01 %CUS41:0.01 FNU/NTU, 0.01 ppm, 0.01 g/l, 0.01 %Temperature:0.1 °C1) acc. to IEC 746-1, for nominal operating conditions DisplayCUS31/CUS41:± 2 % of measured value (min. 0.02 FNU)Temperature:max. 1.0% of measuring rangeSignal outputCUS31/CUS41:1% of current output range (min. 0.02 FNU)Temperature:max. 1.25% of current output range2) acc. to IEC 746-1, for nominal operating conditionsLiquisys M CUM223/253Endress+Hauser11InstallationInstallation instructionsField instrumentMounting on pipes 1 - 3Mounting screws and mounting plateLiquisys M CUM223/25312Endress+HauserView into the field instrument1234Removable electronics box Partition plate Terminal blocks FuseWall mounting of the field instrument 1Mounting holes 2 Protecting capMounting of the field instrument with mounting post and weather protection cover 1 - 3Mounting holesØ6/Ø0.24Liquisys M CUM223/253Endress+Hauser 13Dimensions panel-mounted instrumentInstallation of the panel-mounted instrument 1Wall of control cabinet 2Gasket 3Tensioning screws*Required installation depth92/ 3.62+0.5+0.0292/ 3.62+0.5+0.02Liquisys M CUM223/25314Endress+HauserEnvironmentAmbient temperature -10 to +55 °C (+14 to +131 °F)Storage temperature –25 to +65 °C (-13 to +149 °F)Electromagnetic compatibility Interference emission and interference immunity as per EN 61326-1:2006, EN 61326-2-3:2006Ingress protectionElectrical safety according EN/IEC 61010-1:2001, Installation Category II, for use up to 2000 m above sea level CSAApparatus with CSA General Purpose Approval are certified for indoor use.Relative humidity 10 to 95%, non-condensingPollution degreeThe product is suitable for pollution degree 2.Mechanical constructionDimensionsWeightMaterialTerminalsPanel mounted instrument:IP 54 (front), IP 30 (housing)Field instrument:IP 65 / tightness acc. to NEMA 4XPanel-mounted instrument:96x 96x 145mm (3.78 x 3.78 x 5.71 inches)Installation depth: approx. 165mm (6.50")Field instrument:247x 170x 115mm (9.72 x 6.69 x 4.53 inches)Panel-mounted instrument:max. 0.7kg (1.5 lb)Field instrument:max.2.3kg (5.1 lb)Housing of panel-mounted instrument:Polycarbonate Field housing:ABS PC FrFront membrane:Polyester, UV-resistant Cross sectionmax. 2.5 mm 2 (14 AWG)Liquisys M CUM223/253Endress+Hauser 15OperabilityOperating conceptAll instrument control functions are arranged in a logical menu structure. Following access code entry, the individual parameters can be easily selected and modified as needed.Display elementsOperating elements 1LC display for displaying the measured values and configuration data 2Field for user labelling3 4 main operating keys for calibration and device configuration 4Changeover switch for automatic/manual mode of the relays 5LEDs for limit contactor relay (switch status)6LED for alarm function7Display of the active contact and key for relay changeover in manual modeCertificates and approvals4 symbolDeclaration of conformityThe product meets the requirements of the harmonized European standards. It thus complies with the legal requirements of the EC directives.The manufacturer confirms successful testing of the product by affixing the 4 symbol.CSA General PurposeCSA General PurposeThe products listed below are eligible to bear the CSA Mark shown with adjacent indicators "C" and "US":Version ApprovalCUM253-..2...CUM253-..3...CUM253-..7...CSA Mark for Canada and USACUM223-..2...CUM223-..3...CUM223-..7...CSA Mark for Canada and USALiquisys M CUM223/25316Endress+HauserOrdering informationOrder codeEnter the following address into your browser to access the relevant product page:/cum223 or /cum2531.2.Click "Configure this product".3.The configurator opens in a separate window. You can now configure your device and receive the complete order code that applies for the device.4.Afterwards, export the order code as a PDF or Excel file. To do so, click the appropriate button at the top of the page.Product structureAdditional functions of the Plus package•Current output table to cover wide ranges with varying resolution, fields O33x •Process Check System (PCS): live check of the sensor, function group P •Concentration measurement, function group K •Automatic cleaning function start, field F8Input, software versionTB Suspended solids with factory setup > residual concrete water TU Turbidity and suspended solids measurementTSTurbidity and suspended solids measurement, with additional functions (Plus package)Power supply; approval0230V AC 1115V AC2230V AC; CSA Gen. Purp.3115V AC; CSA Gen. Purp.5100V AC724V AC/DC; CSA Gen. Purp.824V AC/DCOutput0 1 x 20 mA, primary value1 2 x 20 mA, primary value + secondary value 3PROFIBUS PA 4PROFIBUS DP5 1 x 20 mA, primary value, HART62 x 20 mA, primary value, HART + secondary valueAdditional contacts05not selected10 2 relays (limit/P(ID)/timer)15 4 relays (limit/P(ID)/Chemoclean) (not with PROFIBUS DP)16 4 relays (limit/P(ID)/timer) (not with PROFIBUS DP)20 1 x 4 to 20 mA input + 2 relays (limit/P(ID)/timer)25 1 x 4 to 20 mA input + 4 relays (limit/P(ID)/Chemoclean) (not with PROFIBUS DP)261 x 4 to 20 mA input + 4 relays (limit/P(ID)/timer) (not with PROFIBUS DP)Marking1Tagging (Tag), see additional spec.CUM253-complete order codeCUM223-Liquisys M CUM223/253Endress+Hauser 17Scope of deliveryThe delivery of the field instrument includes:•1 transmitter CUM253•1 plug-in screw terminal •1 cable gland Pg 7•1 cable gland Pg 16 reduced •2 cable glands Pg 13.5 •1 Operating Instructions•1 Operating Instructions BA00200C/07/EN •versions with HART communication:1 Operating Instructions Field Communication with HART, BA00208C/07/EN •versions with PROFIBUS communication:1 Operating Instructions Field Communication with PROFIBUS PA/DP, BA00209C/07/EN The delivery of the panel-mounted instrument includes:•1 transmitter CUM223•1 set of plug-in screw terminals •2 tensioning screws •1 Operating Instructions•1 Operating Instructions BA00200C/07/EN •versions with HART communication:1 Operating Instructions Field Communication with HART, BA00208C/07/EN •versions with PROFIBUS communication:1 Operating Instructions Field Communication with PROFIBUS PA/DP, BA00209C/07/ENLiquisys M CUM223/25318Endress+HauserAccessoriesSensorsTurbimax W CUS31•Turbidity sensor for drinking water and wastewater applications, 90 ° scattered light method •Ordering acc. to product structure, see Technical Information (TI176C/07/en)Turbimax W CUS41•Turbidity sensor for wastewater and solid content measurements, 90 ° scattered light method •Ordering acc. to product structure, see Technical Information (TI177C/07/en)Connection accessoriesCYK81 measuring cable•Non-terminated cable for extending the sensor cables (e.g. Memosens)•2x2 wires, twisted with shield and PVC sheath (2x 2x 0.5 mm 2 + shield)•Goods sold by meter, order no.: 51502543Junction box RM•For cable extension (e.g. for Memosens sensors)•5 terminals•Cable entries: 2 x Pg 13.5•Material: PC•Ingress protection: IP 65•Order no.: 51500832Mounting accessoriesCYY101 weather protection cover for field devices, absolutely essential if operating the unit outdoors •Material: stainless steel 1.4031 (AISI 304)•Order No. CYY101-AWeather protection cover for field devicesLiquisys M CUM223/253Endress+Hauser 19Post mounting kit•For mounting of field housing on horizontal or vertical pipes (Ø max. 60 mm (2.36"))•Material: stainless steel 1.4301•order no. 50086842Post mounting kitCYY102 universal post•Square pipe for mounting transmitters •Material: stainless steel 1.4301 (AISI 304)•Order No. CYY102-AUniversal post。
2233调试说明书(服务部10[1]1)服务部调试指导书（2233控制系统）更改记录序号归档单号更改内容描述更改人更改日期01 首次归档王涛2008.3.802 重新整理归档徐新全2008.9.24目录一慢车调试 (4)1检修模式运行条件检查 (4)2观察XTSC2板上的指示灯，检查输入信号是否正确 (5)3主机自学习 (6)4主机定位 (10)二参数设置 (14)1主机速度的设定 (14)2主板参数设定 (14)3群控（双通门）参数设置 (15)三快车调试 (16)1 AMCB2设置 (16)1.1 密码输入 (16)1.2 显示状态及操作按钮 (16)1.3 变频器模拟口整定 (17)1.4 修改AMCB2参数 (18)2确认井道信号 (18)3极限开关的调整 (18)4井道位置自学习 (19)5平衡负载调整 (19)6平层位置的调整 (20)7称重开关调整 (20)8舒适感调整 (20)9试外召、消防、锁梯 (20)四常见功能方法 (21)1查看变频器故障记录 (21)2删除变频器所有故障 (21)3更改电梯上下行方向 (22)4取消抱闸反馈 (22)5取消接触器反馈 (22)6取消门反馈 (22)7调舒适感 (22)8调主机电流声 (22)9调主机电磁声音 (22)10查看主板故障记录 (22)11测试输入输出串行通信信号 (22)五故障排除 (23)1 慢车常见问题 (23)2其他常见问题 (23)3变频器故障分析 (26)附件一常用I/O地址表 (27)附件二常见控制部分服务器信息列表 (28)附件三西威变频器参数 (33)附件四西威变频器故障总结 (42)一慢车调试1检修模式运行条件检查1.1 检查接地线确保控制柜、主机的接地线可靠接地，如果是无机房，控制柜之间的接地需要重点检查。
1.2 检查主机动力线在断电的情况下，万用表打在电阻档，黑表笔接HL端子（接地），红表笔接主动力线R、S、T，是否有短路现象，动力线必须连接可靠，不能有虚接。
