毕业设计方案英文翻译资料中文

英文The road (highway)The road is one kind of linear construction used for travel。

It is made of the roadbed，the road surface, the bridge, the culvert and the tunnel. In addition, it also has the crossing of lines, the protective project and the traffic engineering and the route facility。

The roadbed is the base of road surface, road shoulder，side slope, side ditch foundations. It is stone material structure, which is designed according to route's plane position .The roadbed, as the base of travel, must guarantee that it has the enough intensity and the stability that can prevent the water and other natural disaster from corroding.The road surface is the surface of road. It is single or complex structure built with mixture。

The road surface require being smooth，having enough intensity，good stability and anti—slippery function. The quality of road surface directly affects the safe, comfort and the traffic。

1 工程概论1.1 工程专业1.2 工业和技术1.3 现代制造业工程专业1 工程行业是历史上最古老的行业之一。

如果没有在广阔工程领域中应用的那些技术，我们现在的文明绝不会前进。

第一位把岩石凿削成箭和矛的工具匠是现代机械工程师的鼻祖。

那些发现地球上的金属并找到冶炼和使用金属的方法的工匠们是采矿和冶金工程师的先祖。

那些发明了灌溉系统并建造了远古世纪非凡的建筑物的技师是他们那个时代的土木工程师。

2 工程一般被定义为理论科学的实际应用，例如物理和数学。

许多早期的工程设计分支不是基于科学而是经验信息，这些经验信息取决于观察和经历，而不是理论知识。

这是一个倾斜面实际应用的例子，虽然这个概念没有被确切的理解，但是它可以被量化或者数字化的表达出来。

3 从16、17世纪当代初期，量化就已经成为科学知识大爆炸的首要原因之一。

另外一个重要因素是实验法验证理论的发展。

量化包含了把来源于实验的数据和信息转变成确切的数学术语。

这更加强调了数学是现代工程学的语言。

4 从19世纪开始，它的结果的实际而科学的应用已经逐步上升。

机械工程师现在有精确的能力去计算来源于许多不同机构之间错综复杂的相互作用的机械优势。

他拥有能一起工作的既新型又强硬的材料和巨大的新能源。

工业革命开始于使用水和蒸汽一起工作。

从此使用电、汽油和其他能源作动力的机器变得如此广泛以至于它们承担了世界上很大比例的工作。

5 科学知识迅速膨胀的结果之一就是科学和工程专业的数量的增加。

到19世纪末不仅机械、土木、矿业、冶金工程被建立而且更新的化学和电气工程专业出现了。

这种膨胀现象一直持续到现在。

我们现在拥有了核能、石油、航天航空空间以及电气工程等。

每种工程领域之内都有细分。

6 例如，土木工程自身领域之内有如下细分：涉及永久性结构的建筑工程、涉及水或其他液体流动与控制系统的水利工程、涉及供水、净化、排水系统的研究的环境工程。

机械工程主要的细分是工业工程，它涉及的是错综复杂的机械系统，这些系统是工业上的，而非单独的机器。

英文资料与中文翻译IEEE 802.11 MEDIUM ACCESS CONTROLThe IEEE 802.11 MAC layer covers three functional areas：reliable data delivery, medium access control, and security. This section covers the first two topics.Reliable Data DeliveryAs with any wireless network, a wireless LAN using the IEEE 802.11 physical and MAC layers is subject to considerable unreliability. Noise, interference, and other propagation effects result in the loss of a significant number of frames. Even with error-correction codes, a number of MAC frames may not successfully be received. This situation can be dealt with by reliability mechanisms at a higher layer. such as TCP. However, timers used for retransmission at higher layers are typically on the order of seconds. It is therefore more efficient to deal with errors at the MAC level. For this purpose, IEEE 802.11 includes a frame exchange protocol. When a station receives a data frame from another station. It returns an acknowledgment (ACK) frame to the source station. This exchange is treated as an atomic unit, not to be interrupted by a transmission from any other station. If the source does not receive an ACK within a short period of time, either because its data frame was damaged or because the returning ACK was damaged, the source retransmits the frame.Thus, the basic data transfer mechanism in IEEE802.11 involves an exchange of two frames. To further enhance reliability, a four-frame exchange may be used. In this scheme, a source first issues a request to send (RTS) frame to the destination. The destination then responds with a clear to send (CTS). After receiving the CTS, the source transmits the data frame, and the destination responds with an ACK. The RTS alerts all stations that are within reception range of the source that an exchange is under way; these stations refrain from transmission in order to avoid a collision between two frames transmitted at the same time. Similarly, the CTS alerts all stations that are within reception range of the destination that an exchange is under way. The RTS/CTS portion of the exchange is a required function of the MAC but may be disabled.Medium Access ControlThe 802.11 working group considered two types of proposals for a MAC algorithm: distributed access protocols, which, like Ethernet, distribute the decision to transmit over all the nodes using a carrier-sense mechanism; and centralized access protocols, which involve regulation of transmission by a centralized decision maker. A distributed access protocol makes sense for an ad hoc network of peer workstations (typically an IBSS) and may also be attractive in other wireless LAN configurations that consist primarily of burst traffic. A centralized access protocol is natural for configurations in which a umber of wireless stations are interconnected with each other and some sort of base station that attaches to a backbone wired LAN: it is especially useful if some of the data is time sensitive or high priority.The end result for 802.11 is a MAC algorithm called DFWMAC (distributed foundation wireless MAC) that provides a distributed access control mechanism with an optional centralized control built on top of that. Figure 14.5 illustrates the architecture. The lower sub-layer of the MAC layer is the distributed coordination function (DCF). DCF uses a contention algorithm to provide access to all traffic. Ordinary asynchronous traffic directly uses DCE. The point coordination function (PCF) is a centralized MAC algorithm used to provide contention-free service. PCF is built on top of DCF and exploits features of DCF to assure access for its users. Let us consider these two sub-layers in turn.MAClayerFigure 14.5 IEEE 802.11 Protocol ArchitectureDistributed Coordination FunctionThe DCF sub-layer makes use of a simple CSMA (carrier sense multiple access) algorithm, which functions as follows. If a station has a MAC frame to transmit, it listens to the medium. If the medium is idle, the station may transmit; otherwise the station must wait until the current transmission is complete before transmitting. The DCF does not include a collision detection function (i.e. CSMA/CD) because collision detection is not practical on a wireless network. The dynamic range of the signals on the medium is very large, so that a transmitting station cannot effectively distinguish incoming weak signals from noise and the effects of its own transmission.To ensure the smooth and fair functioning of this algorithm, DCF includes a set of delays that amounts to a priority scheme. Let us start by considering a single delay known as an inter-frame space (IFS). In fact, there are three different IFS values, but the algorithm is best explained by initially ignoring this detail. Using an IFS, the rules for CSMA access are as follows (Figure 14.6):Figure 14.6 IEEE 802.11 Medium Access Control Logic1. A station with a frame to transmit senses the medium. If the medium is idle. It waits to see if the medium remains idle for a time equal to IFS. If so , the station may transmit immediately.2. If the medium is busy (either because the station initially finds the medium busy or because the medium becomes busy during the IFS idle time), the station defers transmission and continues to monitor the medium until the current transmission is over.3. Once the current transmission is over, the station delays another IFS. If the medium remains idle for this period, then the station backs off a random amount of time and again senses the medium. If the medium is still idle, the station may transmit. During the back-off time, if the medium becomes busy, the back-off timer is halted and resumes when the medium becomes idle.4. If the transmission is unsuccessful, which is determined by the absence of an acknowledgement, then it is assumed that a collision has occurred.To ensure that back-off maintains stability, a technique known as binary exponential back-off is used. A station will attempt to transmit repeatedly in the face of repeated collisions, but after each collision, the mean value of the random delay is doubled up to some maximum value. The binary exponential back-off provides a means of handling a heavy load. Repeated failed attempts to transmit result in longer and longer back-off times, which helps to smooth out the load. Without such a back-off, the following situation could occur. Two or more stations attempt to transmit at the same time, causing a collision. These stations then immediately attempt to retransmit, causing a new collision.The preceding scheme is refined for DCF to provide priority-based access by the simple expedient of using three values for IFS:●SIFS (short IFS):The shortest IFS, used for all immediate responseactions，as explained in the following discussion●PIFS (point coordination function IFS):A mid-length IFS, used by thecentralized controller in the PCF scheme when issuing polls●DIFS (distributed coordination function IFS): The longest IFS, used as aminimum delay for asynchronous frames contending for access Figure 14.7a illustrates the use of these time values. Consider first the SIFS.Any station using SIFS to determine transmission opportunity has, in effect, the highest priority, because it will always gain access in preference to a stationwaiting an amount of time equal to PIFS or DIFS. The SIFS is used in the following circumstances：●Acknowledgment (ACK): When a station receives a frame addressed onlyto itself (not multicast or broadcast) it responds with an ACK frame after, waiting on1y for an SIFS gap. This has two desirable effects. First, because collision detection IS not used, the likelihood of collisions is greater than with CSMA/CD, and the MAC-level ACK provides for efficient collision recovery. Second, the SIFS can be used to provide efficient delivery of an LLC protocol data unit (PDU) that requires multiple MAC frames. In this case, the following scenario occurs. A station with a multi-frame LLC PDU to transmit sends out the MAC frames one at a time. Each frame is acknowledged after SIFS by the recipient. When the source receives an ACK, it immediately (after SIFS) sends the next frame in the sequence. The result is that once a station has contended for the channel, it will maintain control of the channel until it has sent all of the fragments of an LLC PDU.●Clear to Send (CTS):A station can ensure that its data frame will getthrough by first issuing a small. Request to Send (RTS) frame. The station to which this frame is addressed should immediately respond with a CTS frame if it is ready to receive. All other stations receive the RTS and defer using the medium.●Poll response: This is explained in the following discussion of PCF.longer than DIFS(a) Basic access methodasynchronous trafficdefers(b) PCF super-frame constructionFigure 14.7 IEEE 802.11 MAC TimingThe next longest IFS interval is the: PIFS. This is used by the centralized controller in issuing polls and takes precedence over normal contention traffic. However, those frames transmitted using SIFS have precedence over a PCF poll.Finally, the DIFS interval is used for all ordinary asynchronous traffic.Point C00rdination Function PCF is an alternative access method implemented on top of the DCE. The operation consists of polling by the centralized polling master (point coordinator). The point coordinator makes use of PIFS when issuing polls. Because PI FS is smaller than DIFS, the point coordinator call seize the medium and lock out all asynchronous traffic while it issues polls and receives responses.As an extreme, consider the following possible scenario. A wireless network is configured so that a number of stations with time, sensitive traffic are controlled by the point coordinator while remaining traffic contends for access using CSMA. The point coordinator could issue polls in a round—robin fashion to all stations configured for polling. When a poll is issued, the polled station may respond using SIFS. If the point coordinator receives a response, it issues another poll using PIFS. If no response is received during the expected turnaround time, the coordinator issues a poll．If the discipline of the preceding paragraph were implemented, the point coordinator would lock out all asynchronous traffic by repeatedly issuing polls. To prevent this, an interval known as the super-frame is defined. During the first part of this interval, the point coordinator issues polls in a round, robin fashion to all stations configured for polling. The point coordinator then idles for the remainder of the super-frame, allowing a contention period for asynchronous access.Figure l4.7 b illustrates the use of the super-frame. At the beginning of a super-frame, the point coordinator may optionally seize control and issues polls for a give period of time. This interval varies because of the variable frame size issued by responding stations. The remainder of the super-frame is available for contention based access. At the end of the super-frame interval, the point coordinator contends for access to the medium using PIFS. If the medium is idle. the point coordinator gains immediate access and a full super-frame period follows. However, the medium may be busy at the end of a super-frame. In this case, the point coordinator must wait until the medium is idle to gain access: this result in a foreshortened super-frame period for the next cycle.OctetsFC=frame control SC=sequence controlD/I=duration/connection ID FCS=frame check sequence（a ） MAC frameBitsDS=distribution systemMD=more data MF=more fragmentsW=wired equivalent privacy RT=retryO=orderPM=power management (b) Frame control filedFigure 14.8 IEEE 802.11 MAC Frame FormatMAC FrameFigure 14.8a shows the 802.11 frame format when no security features are used. This general format is used for all data and control frames, but not all fields are used in all contexts. The fields are as follows:● Frame Control: Indicates the type of frame and provides contr01information, as explained presently.● Duration/Connection ID: If used as a duration field, indicates the time(in-microseconds) the channel will be allocated for successful transmission of a MAC frame. In some control frames, this field contains an association, or connection, identifier.●Addresses: The number and meaning of the 48-bit address fields dependon context. The transmitter address and receiver address are the MAC addresses of stations joined to the BSS that are transmitting and receiving frames over the wireless LAN. The service set ID (SSID) identifies the wireless LAN over which a frame is transmitted. For an IBSS, the SSID isa random number generated at the time the network is formed. For awireless LAN that is part of a larger configuration the SSID identifies the BSS over which the frame is transmitted: specifically, the SSID is the MAC-level address of the AP for this BSS (Figure 14.4). Finally the source address and destination address are the MAC addresses of stations, wireless or otherwise, that are the ultimate source and destination of this frame. The source address may be identical to the transmitter address and the destination address may be identical to the receiver address.●Sequence Control: Contains a 4-bit fragment number subfield used forfragmentation and reassembly, and a l2-bit sequence number used to number frames sent between a given transmitter and receiver.●Frame Body: Contains an MSDU or a fragment of an MSDU. The MSDUis a LLC protocol data unit or MAC control information.●Frame Check Sequence: A 32-bit cyclic redundancy check. The framecontrol filed, shown in Figure 14.8b, consists of the following fields.●Protocol Version: 802.11 version, current version 0.●Type: Identifies the frame as control, management, or data.●Subtype: Further identifies the function of frame. Table 14.4 defines thevalid combinations of type and subtype.●To DS: The MAC coordination sets this bit to 1 in a frame destined to thedistribution system.●From DS: The MAC coordination sets this bit to 1 in a frame leaving thedistribution system.●More Fragments: Set to 1 if more fragments follow this one.●Retry: Set to 1 if this is a retransmission of a previous frame.●Power Management: Set to]if the transmitting station is in a sleep mode.●More Data: Indicates that a station has additional data to send. Each blockof data may be sent as one frame or a group of fragments in multiple frames.●WEP：Set to 1 if the optional wired equivalent protocol is implemented.WEP is used in the exchange of encryption keys for secure data exchange.This bit also is set if the newer WPA security mechanism is employed, as described in Section 14.6.●Order：Set to 1 in any data frame sent using the Strictly Ordered service,which tells the receiving station that frames must be processed in order. We now look at the various MAC frame types.Control Frames Control frames assist in the reliable delivery of data frames. There are six control frame subtypes:●Power Save-Poll (PS-Poll): This frame is sent by any station to the stationthat includes the AP (access point). Its purpose is to request that the AP transmit a frame that has been buffered for this station while the station was in power saving mode.●Request to Send (RTS):This is the first frame in the four-way frameexchange discussed under the subsection on reliable data delivery at the beginning of Section 14.3.The station sending this message is alerting a potential destination, and all other stations within reception range, that it intends to send a data frame to that destination.●Clear to Send (CTS): This is the second frame in the four-way exchange.It is sent by the destination station to the source station to grant permission to send a data frame.●Acknowledgment:Provides an acknowledgment from the destination tothe source that the immediately preceding data, management, or PS-Poll frame was received correctly.●Contention-Free (CF)-End: Announces the end of a contention-freeperiod that is part of the point coordination function.●CF-End+CF-Ack:Acknowledges the CF-End. This frame ends thecontention-free period and releases stations from the restrictions associated with that period.Data Frames There are eight data frame subtypes, organized into two groups. The first four subtypes define frames that carry upper-level data from the source station to the destination station. The four data-carrying frames are as follows: ●Data: This is the simplest data frame. It may be used in both a contentionperiod and a contention-free period.●Data+CF-Ack: May only be sent during a contention-free period. Inaddition to carrying data, this frame acknowledges previously received data.●Data+CF-Poll: Used by a point coordinator to deliver data to a mobilestation and also to request that the mobile station send a data frame that it may have buffered.●Data+CF-Ack+CF-Poll: Combines the functions of the Data+CF-Ack andData+CF-Poll into a single frame.The remaining four subtypes of data frames do not in fact carry any user data. The Null Function data frame carries no data, polls, or acknowledgments. It is used only to carry the power management bit in the frame control field to the AP, to indicate that the station is changing to a low-power operating state. The remaining three frames (CF-Ack, CF-Poll,CF-Ack+CF-Poll) have the same functionality as the corresponding data frame subtypes in the preceding list (Data+CF-Ack, Data+CF-Poll, Data+CF-Ack+CF-Poll) but withotit the data. Management FramesManagement frames are used to manage communications between stations and APs. The following subtypes are included:●Association Request：Sent by a station to an AP to request an association,with this BSS. This frame includes capability information, such as whether encryption is to be used and whether this station is pollable.●Association Response:Returned by the AP to the station to indicatewhether it is accepting this association request.●Reassociation Request: Sent by a station when it moves from one BSS toanother and needs to make an association with tire AP in the new BSS. The station uses reassociation rather than simply association so that the new AP knows to negotiate with the old AP for the forwarding of data frames.●Reassociation Response:Returned by the AP to the station to indicatewhether it is accepting this reassociation request.●Probe Request: Used by a station to obtain information from anotherstation or AP. This frame is used to locate an IEEE 802.11 BSS.●Probe Response: Response to a probe request.●Beacon: Transmitted periodically to allow mobile stations to locate andidentify a BSS.●Announcement Traffic Indication Message: Sent by a mobile station toalert other mobile stations that may have been in low power mode that this station has frames buffered and waiting to be delivered to the station addressed in this frame.●Dissociation: Used by a station to terminate an association.●Authentication：Multiple authentication frames are used in an exchange toauthenticate one station to another.●Deauthentication:Sent by a station to another station or AP to indicatethat it is terminating secure communications.IEEE802.11 媒体接入控制IEEE 802．11 MAC层覆盖了三个功能区：可靠的数据传送、接入控制以及安全。

A Comparison of Soft Start Mechanisms for Mining BeltConveyors1800 Washington Road Pittsburgh, PA 15241 Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.INTRODUCTIONThe force required to move a belt conveyor must be transmitted by the drive pulley via friction between the drive pulley and the belt fabric. In order to transmit power there must be a difference in the belt tension as it approaches and leaves the drive pulley. These conditions are true for steady state running, starting, and stopping. Traditionally, belt designs are based on static calculations of running forces. Since starting and stopping are not examined in detail, safety factors are applied to static loadings (Harrison, 1987). This paper will primarily address the starting or acceleration duty of the conveyor. The belt designer must control starting acceleration to prevent excessive tension in the belt fabric and forces in the belt drive system (Suttees, 1986). High acceleration forces can adversely affect the belt fabric, belt splices, drive pulleys, idler pulleys, shafts, bearings, speed reducers, and couplings. Uncontrolled acceleration forces can cause belt conveyor system performance problems with vertical curves, excessive belt take-up movement, loss of drive pulley friction, spillage of materials, and festooning of the belt fabric. The belt designer is confronted with two problems, The belt drive system must produce a minimum torque powerful enough to start the conveyor, and controlled such that the acceleration forces are within safe limits. Smooth starting of the conveyor can be accomplished by the use of drive torque control equipment, either mechanical or electrical, or a combination of the two (CEM, 1979).SOFT START MECHANISM EVALUATION CRITERIONWhat is the best belt conveyor drive system? The answer depends on many variables. The best system is one that provides acceptable control for starting, running, and stopping at a reasonable cost and with high reliability (Lewdly and Sugarcane, 1978). Belt Drive System For the purposes of this paper we will assume that belt conveyors are almost always driven byelectrical prime movers (Goodyear Tire and Rubber, 1982). The belt "drive system" shall consist of multiple components including the electrical prime mover, the electrical motor starter with control system, the motor coupling, the speed reducer, the low speed coupling, the belt drive pulley, and the pulley brake or hold back (Cur, 1986). It is important that the belt designer examine the applicability of each system component to the particular application. For the purpose of this paper, we will assume that all drive system components are located in the fresh air, non-permissible, areas of the mine, or in non-hazardous, National Electrical Code, Article 500 explosion-proof, areas of the surface of the mine.Belt Drive Component Attributes SizeCertain drive components are available and practical in different size ranges. For this discussion, we will assume that belt drive systems range from fractional horsepower to multiples of thousands of horsepower. Small drive systems are often below 50 horsepower. Medium systems range from 50 to 1000 horsepower. Large systems can be considered above 1000 horsepower. Division of sizes into these groups is entirely arbitrary. Care must be taken to resist the temptation to over motor or under motor a belt flight to enhance standardization. An over motored drive results in poor efficiency and the potential for high torques, while an under motored drive could result in destructive overspending on regeneration, or overheating with shortened motor life (Lords, et al., 1978).Torque ControlBelt designers try to limit the starting torque to no more than 150% of the running torque (CEMA, 1979; Goodyear, 1982). The limit on the applied starting torque is often the limit of rating of the belt carcass, belt splice, pulley lagging, or shaft deflections. On larger belts and belts with optimized sized components, torque limits of 110% through 125% are common (Elberton, 1986). In addition to a torque limit, the belt starter may be required to limit torque increments that would stretch belting and cause traveling waves. An ideal starting control system would apply a pretension torque to the belt at rest up to the point of breakaway, or movement of the entire belt, then a torque equal to the movement requirements of the belt with load plus a constant torque to accelerate the inertia of the system components from rest to final running speed. This would minimize system transient forces and belt stretch (Shultz, 1992). Different drive systems exhibit varying ability to control the application of torques to the belt at rest and at different speeds. Also, the conveyor itself exhibits two extremes of loading. An empty belt normally presents the smallest required torque for breakaway and acceleration, while a fully loaded belt presents the highest required torque. A mining drive system must be capable of scaling the applied torque from a 2/1 ratio for a horizontal simple belt arrangement, to a 10/1 ranges for an inclined or complex belt profile.Thermal RatingDuring starting and running, each drive system may dissipate waste heat. The waste heat may be liberated in the electrical motor, the electrical controls,, the couplings, the speed reducer, or the belt braking system. The thermal load of each start Is dependent on the amount of belt load and the duration of the start. The designer must fulfill the application requirements for repeated starts after running the conveyor at full load. Typical mining belt starting duties vary from 3 to 10 starts per hour equally spaced, or 2 to 4 starts in succession. Repeated starting may require the dreading or over sizing of system components. There is a direct relationship between thermal rating for repeated starts and costs. Variable Speed. Some belt drive systems are suitable for controlling the starting torque and speed, but only run at constant speed. Some belt applications would require a drive system capable of running for extended periods at less than full speed. This is useful when the drive load must be shared with other drives, the belt is used as a process feeder for rate control of the conveyed material, the belt speed is optimized for the haulage rate, the belt is used at slower speeds to transport men or materials, or the belt is run a slow inspection or inching speed for maintenance purposes (Hager, 1991). The variable speed belt drive will require a control system based on some algorithm to regulate operating speed. Regeneration or Overhauling Load. Some belt profiles present the potential for overhauling loads where the belt system supplies energy to the drive system. Not all drive systems have the ability to accept regenerated energy from the load. Some drives can accept energy from the load and return it to the power line for use by other loads. Other drives accept energy from the load and dissipate it into designated dynamic or mechanical braking elements. Some belt profiles switch from motoring to regeneration during operation. Can the drive system accept regenerated energy of a certain magnitude for the application? Does the drive system have to control or modulate the amount of retarding force during overhauling? Does the overhauling occur when running and starting? Maintenance and Supporting Systems. Each drive system will require periodic preventative maintenance. Replaceable items would include motor brushes, bearings, brake pads, dissipation resistors, oils, and cooling water. If the drive system is conservatively engineered and operated, the lower stress on consumables will result in lower maintenance costs. Some drives require supporting systems such as circulating oil for lubrication, cooling air or water, environmental dust filtering, or computer instrumentation. The maintenance of the supporting systems can affect the reliability of the drive system.CostThe drive designer will examine the cost of each drive system. The total cost is the sum of the first capital cost to acquire the drive, the cost to install and commission the drive, thecost to operate the drive, and the cost to maintain the drive. The cost for power to operate the drive may vary widely with different locations. The designer strives to meet all system performance requirements at lowest total cost. Often more than one drive system may satisfy all system performance criterions at competitive costs.ComplexityThe preferred drive arrangement is the simplest, such as a single motor driving through a single head pulley.However,mechanical, economic,and functional requirements often necessitate the use of complex drives.The belt designer must balance the need for sophistication against the problems that accompany complex systems. Complex systems require additional design engineering for successful deployment. An often-overlooked cost in a complex system is the cost of training onsite personnel, or the cost of downtime as a result of insufficient training.SOFT START DRIVE CONTROL LOGICEach drive system will require a control system to regulate the starting mechanism. The most common type of control used on smaller to medium sized drives with simple profiles is termed "Open Loop Acceleration Control". In open loop, the control system is previously configured to sequence the starting mechanism in a prescribed manner, usually based on time. In open loop control, drive-operating parameters such as current, torque, or speed do not influence sequence operation. This method presumes that the control designer has adequately modeled drive system performance on the conveyor. For larger or more complex belts, "Closed Loop" or "Feedback" control may he utilized. In closed loop control, during starting, the control system monitors via sensors drive operating parameters such as current level of the motor, speed of the belt, or force on the belt, and modifies the starting sequence to control, limit, or optimize one or wore parameters. Closed loop control systems modify the starting applied force between an empty and fully loaded conveyor. The constants in the mathematical model related to the measured variable versus the system drive response are termed the tuning constants. These constants must be properly adjusted for successful application to each conveyor. The most common schemes for closed loop control of conveyor starts are tachometer feedback for speed control and load cell force or drive force feedback for torque control. On some complex systems, It is desirable to have the closed loop control system adjust itself for various encountered conveyor conditions. This is termed "Adaptive Control". These extremes can involve vast variations in loadings, temperature of the belting, location of the loading on the profile, or multiple drive options on the conveyor. There are three commonadaptive methods. The first involves decisions made before the start, or 'Restart Conditioning'. If the control system could know that the belt is empty, it would reduce initial force and lengthen the application of acceleration force to full speed. If the belt is loaded, the control system would apply pretension forces under stall for less time and supply sufficient torque to adequately accelerate the belt in a timely manner. Since the belt only became loaded during previous running by loading the drive, the average drive current can be sampled when running and retained in a first-in-first-out buffer memory that reflects the belt conveyance time. Then at shutdown the FIFO average may be use4 to precondition some open loop and closed loop set points for the next start. The second method involves decisions that are based on drive observations that occur during initial starting or "Motion Proving'. This usually involves a comparison In time of the drive current or force versus the belt speed. if the drive current or force required early in the sequence is low and motion is initiated, the belt must be unloaded. If the drive current or force required is high and motion is slow in starting, the conveyor must be loaded. This decision can be divided in zones and used to modify the middle and finish of the start sequence control. The third method involves a comparison of the belt speed versus time for this start against historical limits of belt acceleration, or 'Acceleration Envelope Monitoring'. At start, the belt speed is measured versus time. This is compared with two limiting belt speed curves that are retained in control system memory. The first curve profiles the empty belt when accelerated, and the second one the fully loaded belt. Thus, if the current speed versus time is lower than the loaded profile, it may indicate that the belt is overloaded, impeded, or drive malfunction. If the current speed versus time is higher than the empty profile, it may indicate a broken belt, coupling, or drive malfunction. In either case, the current start is aborted and an alarm issued.CONCLUSIONThe best belt starting system is one that provides acceptable performance under all belt load Conditions at a reasonable cost with high reliability. No one starting system meets all needs. The belt designer must define the starting system attributes that are required for each belt. In general, the AC induction motor with full voltage starting is confined to small belts with simple profiles. The AC induction motor with reduced voltage SCR starting is the base case mining starter for underground belts from small to medium sizes. With recent improvements, the AC motor with fixed fill fluid couplings is the base case for medium to large conveyors with simple profiles. The Wound Rotor Induction Motor drive is the traditional choice for medium to large belts with repeated starting duty or complex profilesthat require precise torque control. The DC motor drive, Variable Fill Hydrokinetic drive, and the Variable Mechanical Transmission drive compete for application on belts with extreme profiles or variable speed at running requirements. The choice is dependent on location environment, competitive price, operating energy losses, speed response, and user familiarity. AC Variable Frequency drive and Brush less DC applications are limited to small to medium sized belts that require precise speed control due to higher present costs and complexity. However, with continuing competitive and technical improvements, the use of synthesized waveform electronic drives will expand.REFERENCES[1]Michael L. Nave, P.E.1989.CONSOL Inc.煤矿业带式输送机几种软起动方式的比较1800 年华盛顿路匹兹堡, PA 15241带式运送机是采矿工业运输大批原料的重要方法。

本科生毕业设计（论文）外文翻译毕业设计（论文）题目：电力系统检测与计算外文题目：The development of the single chipmicrocomputer译文题目：单片机技术的发展与应用学生姓名： XXX专业： XXX指导教师姓名： XXX评阅日期：单片机技术的发展与应用从无线电世界到单片机世界现代计算机技术的产业革命，将世界经济从资本经济带入到知识经济时代。

在电子世界领域，从 20 世纪中的无线电时代也进入到 21 世纪以计算机技术为中心的智能化现代电子系统时代。

现代电子系统的基本核心是嵌入式计算机系统(简称嵌入式系统)，而单片机是最典型、最广泛、最普及的嵌入式系统。

一、无线电世界造就了几代英才。

在 20 世纪五六十年代，最具代表的先进的电子技术就是无线电技术，包括无线电广播，收音，无线通信(电报)，业余无线电台，无线电定位，导航等遥测、遥控、遥信技术。

早期就是这些电子技术带领着许多青少年步入了奇妙的电子世界，无线电技术展示了当时科技生活美妙的前景。

电子科学开始形成了一门新兴学科。

无线电电子学，无线通信开始了电子世界的历程。

无线电技术不仅成为了当时先进科学技术的代表，而且从普及到专业的科学领域，吸引了广大青少年，并使他们从中找到了无穷的乐趣。

从床头的矿石收音机到超外差收音机；从无线电发报到业余无线电台；从电话，电铃到无线电操纵模型。

无线电技术成为当时青少年科普、科技教育最普及，最广泛的内容。

至今，许多老一辈的工程师、专家、教授当年都是无线电爱好者。

无线电技术的无穷乐趣，无线电技术的全面训练，从电子学基本原理，电子元器件基础到无线电遥控、遥测、遥信电子系统制作，培养出了几代科技英才。

二、从无线电时代到电子技术普及时代。

早期的无线电技术推动了电子技术的发展，其中最主要的是真空管电子技术向半导体电子技术的发展。

半导体电子技术使有源器件实现了微小型化和低成本，使无线电技术有了更大普及和创新，并大大地开阔了许多非无线电的控制领域。

金刚钻的工业化运用一个程序一般需要50至70美网。

在这样的切割频率下，工具的负载量是比较低的。

而欧洲这样的程序下金刚钻的模型是完全不一样的！在我国，在这样的程序下，普遍金刚钻工具在非常自由的切割条件下，产品是不规则的易碎的微粒！在欧洲因为各种因素，情况是不同的。

因为欧洲的生活水平远高于我国，因此，他们的劳动力成本也要高。

为了使欧洲最大的石材生产商保持竞争力，他们必须要把注意力从原材料转移到生产的有效输出和最大化输出。

这就要求产品从原材料到成品的生产过程中尽可能减小能源的耗费和不必要的浪费。

该方法需要机床技术能够高速运作和先进的加工，可进行可靠的长时间持续的，无人值守操作。

在20世纪90年代，在机械和金刚石工具技术方面有很大的发展，使产量增加和降低生产成本。

如果我们对比一下欧洲和中国生产标准，我们可以看到在机器和工具的生产方面，中欧存在很大的差距。

在欧洲，制造这些瓷砖几乎是完全自动的，因为高效率的机械设计和自动处理设施。

最新一代的锯床这种应用能够使用主轴高达80分直径锯片。

机器和工具的设计，在达到下列的参数下，切割率是可以更快的。

•表面速度：- 25 – 35m / s•切削深度：-1mm•大桥速度：- 17m/min•切割速度：- IPOcm/5min或1m/h每个刀片•机输出：- 640m/5day（8小时每天）在这样的条件下，生产浪费减至最低，产量确更高。

通常情况下，在欧洲，刀片会产生10mm的缺口，而中国有12mm。

并且相对于中国12-15mm的切面的切口，欧洲只有10-12mm的切口。

在实现生产最大化材料处理和优化加工时间也是关键，厚片的切据被自动转移到自动的二次加工。

在这样精确的切割率下，对于金刚钻工具的要求是很高的，在程序控制下，型号和尺寸与中国的标准下是有很大不同的。

由于切割率相对高很多，最通常的尺寸是30-50。

切割率高，意味着工具的负载量也高，金刚钻的性质也会不一样！金刚钻的要求一般都是统一的，强大，块状颗粒，这是使在长时间的高负荷下，保持高产量。

毕业设计外文文献翻译专业学生姓名班级学号指导教师优集学院外文资料名称：Knowledge-Based Engineeri--ng Design Methodology外文资料出处：Int.J.Engng Ed.Vol.16.No.1附件： 1.外文资料翻译译文2.外文原文基于知识工程(KBE)设计方法D. E. CALKINS1.背景复杂系统的发展需要很多工程和管理方面的知识、决策，它要满足很多竞争性的要求。

设计被认为是决定产品最终形态、成本、可靠性、市场接受程度的首要因素。

高级别的工程设计和分析过程(概念设计阶段)特别重要，因为大多数的生命周期成本和整体系统的质量都在这个阶段。

产品成本的压缩最可能发生在产品设计的最初阶段。

整个生命周期阶段大约百分之七十的成本花费在概念设计阶段结束时，缩短设计周期的关键是缩短概念设计阶段，这样同时也减少了工程的重新设计工作量。

工程权衡过程中采用良好的估计和非正式的启发进行概念设计。

传统CAD工具对概念设计阶段的支持非常有限。

有必要，进行涉及多个学科的交流合作来快速进行设计分析(包括性能，成本，可靠性等)。

最后，必须能够管理大量的特定领域的知识。

解决方案是在概念设计阶段包含进更过资源，通过消除重新设计来缩短整个产品的时间。

所有这些因素都主张采取综合设计工具和环境，以在早期的综合设计阶段提供帮助。

这种集成设计工具能够使由不同学科的工程师、设计者在面对复杂的需求和约束时能够对设计意图达成共识。

那个设计工具可以让设计团队研究在更高级别上的更多配置细节。

问题就是架构一个设计工具，以满足所有这些要求。

2.虚拟(数字)原型模型现在需要是一种代表产品设计为得到一将允许一产品的早发展和评价的真实事实上原型的过程的方式。

虚拟样机将取代传统的物理样机，并允许设计工程师，研究“假设”的情况，同时反复更新他们的设计。

真正的虚拟原型，不仅代表形状和形式，即几何形状，它也代表如重量，材料，性能和制造工艺的非几何属性。

（Sheaｒ waｌl ｓt ｒuctural desigｎ ofh ｉgh-ｌev ｅl fr ａmeworkＷｕ Jiche ｎgＡbstract ： In t ｈis pape ｒ the basic c ｏｎcepts of ｍａn ｐow ｅr ｆｒom th ｅ ｆra ｍｅ sh ｅａr w ａｌl str ｕc ｔｕｒｅ, analy ｓis of the ｓtruct ｕr ａｌ des ｉgn ｏf th ｅ c ｏnt ｅnt ｏｆ t ｈe fr ａme she ａr wall, in ｃｌudi ｎg the ｓeism ｉc wa ｌl she ａr spa本科毕业设计外文文献翻译学校代码： 10128学 号：题 目：Shear wall structural design of high-level framework 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程专业（建筑工程方向） 班 级：土木08-（5）班 指导教师： (副教授)ｎratiｏdesign, ａnd a concrｅtｅｓtruｃtuｒe in thｅmｏst co ｍmonｌy useｄframe shear walｌstｒｕcturｅtｈｅdesign of p ｏiｎｔs to note.Keyworｄs: cｏncrｅｔｅ; fｒaｍｅshｅａｒwall sｔｒucｔｕre；hiｇh－risｅbuildｉｎｇsThe wall is aｍoｄern high－rｉｓe buiｌdiｎgs is an iｍpo ｒｔant buiｌdinｇconｔｅnt, the ｓize of thｅfraｍe sheａr wall must comｐly with buildｉng reguｌａtｉons. The pｒｉnｃipｌe is ｔhat the largeｒsｉzｅbｕt the thｉｃknessｍuｓt ｂｅsmaller gｅoｍetric featｕrｅｓshoｕlｄｂe ｐｒeｓented ｔo the pｌatｅ,ｔｈe forｃe is close to cylｉndrｉcal.Ｔhe waｌl sｈｅar wa ｌl strｕｃｔure ｉs a flaｔcomｐonent. Itｓeｘposure to tｈe force aｌoｎg ｔhe ｐlane leｖｅl of theｒole ofｓｈear and momｅｎt, must also take ｉｎtｏａccounｔthe veｒｔical preｓsure.Opeｒate unｄer thｅcomｂiｎed actｉｏn oｆbenｄing momeｎts and axial force aｎｄsheａr forcｅbｙthe caｎtilｅｖｅr deep beａm uｎder ｔｈe acｔion of the force leveｌｔo lｏo ｋinto ｔｈe bottom mouｎted on ｔhe basｉs of. Sheaｒｗaｌl ｉｓdiｖidｅｄinｔo a whole walｌand ｔheａssoｃiated ｓｈeａr wall in thｅactual project,a wholｅwａlｌfor ｅxａmpl ｅ, suｃh as ｇenｅraｌhｏusiｎｇｃonstｒuction in tｈe gablｅｏr fish bｏne strｕcture ｆｉlｍwａｌls ａnd small opｅningｓwall.Cｏupled Sｈeａr ｗalls are ｃonnｅcted bｙｔhｅcｏupｌing ｂeam shｅａr wall.Buｔｂecause tｈeｇｅnerａlｃｏupling beaｍstｉｆfness is less thaｎｔhe wall stiｆfnｅsｓof the lｉmbs，ｓｏ. Wａlｌliｍb aｌonｅis obviｏus.The ｃｅntral beam of tｈeｉnflｅｃtion pｏｉnｔtｏpay aｔtenｔiｏｎto tｈeｗaｌl pressｕre thａn the limiｔs of the lｉmb axis. Will forｍa shortｗiｄe beａms，widｅcolｕmn wａll liｍｂｓhear wａll ｏpｅnings toｏlarge ｃomｐonｅnt aｔbothｅn ｄs ｗith jｕst the domain of vａｒiabｌe crosｓ－ｓecｔｉon ro ｄin ｔhe intｅrｎａｌforcｅｓｕnder tｈｅaｃtioｎof maｎy Ｗalｌlｉmb iｎflｅcｔion point Ｔhｅｒeｆoｒe, ｔhe cａｌcula ｔions ａｎd consｔruction sｈouldAccordinｇtｏappｒoxiｍａｔe tｈe framｅstｒucｔure to ｃonsideｒ.Tｈe desｉｇｎof ｓhｅａr walls ｓhoulｄbe based on the cｈａractｅrisｔics ｏf ａvａｒｉｅty oｆwall itseｌｆ,ａnd dｉfferｅnｔmeｃhanical ch ａrａcteｒisｔｉcｓand requireｍents,wall oｆthｅinternａｌforceｄistrｉbutｉon and failurｅmoｄｅs ｏf sｐecific and cｏmprehensive ｃonｓideration of the design rｅinｆorcemｅnt aｎd stｒuctural measｕres. Ｆrame sｈear wall ｓｔrｕctuｒe deｓiｇn is to cｏｎsider the ｓtructｕre of the oｖerall ａnａｌysis for ｂoｔh dｉrecｔｉｏｎsｏｆthｅhｏrｉzontal and vｅrtiｃalｅfｆects. Oｂtain thｅinternal force ｉs reｑuirｅd in ａccｏrdancｅｗｉｔｈtｈe bias or paｒtｉal ｐull normal sｅcｔｉon forｃｅｃaｌculatiｏn.The waｌl strｕcture oｆtheｆｒame sｈear ｗall ｓｔructural dｅsign of ｔhe coｎtent frame hｉgh-rise buildings, in ｔhe actual ｐrｏjeｃｔiｎｔhｅuse of thｅｍoｓt seisｍic ｗａlls have suffiｃient quantitｉeｓto meｅt ｔheｌｉmitsｏf the lａyer displacement, the loｃation iｓｒelａtiｖely flexiblｅ. Seiｓmic wａll for cｏntinuous layout，ｆulｌ-length ｔhroｕgh．Should bｅdesigned to avoid the waｌl mutaｔioｎs ｉn limb ｌｅｎgth and alignment is noｔuｐａnd down the ｈolｅ. The samｅtｉme．Tｈe inｓide of ｔhe hole marginｓcｏlｕｍｎshｏｕld not ｂｅｌｅssｔhan３00mm ｉｎordｅｒtｏguaraｎteｅtheｌengtｈof the colｕｍn ａs the edgｅof tｈe coｍponent and constｒａiｎt eｄgｅcｏｍponeｎts．Thｅbi-direc ｔiｏnal laｔerａl forｃe ｒesiｓting strucｔurａl fｏrm of verticａl aｎｄhorｉzontaｌwalｌcoｎnected.Eａｃh ｏｔhｅr as ｔhe ａffiｎiｔｙof the shｅar wall. Ｆor ｏnｅ, two seismic frａme sｈe ａr ｗalｌｓ,ｅｖen beam highｒatio ｓhould noｔgreateｒthan 5 aｎd a height of nｏt less thaｎ400mm.Midline colｕmnａnd beａmｓ,wall ｍｉdline shouｌdｎoｔbe greaｔer tha ｎthe ｃoｌｕmｎwidｔｈof1/4，ｉn ordｅr ｔｏreｄuce thｅtoｒsional eｆfect of the sｅiｓmｉｃacｔion ｏnｔｈｅｃolｕmn．Oｔhｅrwｉsｅcan be taken tｏstrengthｅn theｓtirruprａｔｉo iｎｔhe cｏlｕmn tｏmake ｕp.If thｅshear wａｌl sheａｒsｐａn ｔhａnｔhe ｂig twｏ. Ｅveｎthe beａｍcro ｓs-heｉｇht ratiｏgreateｒthan 2.5, ｔhen tｈe design presｓｕｒe ｏf thｅｃｕt shoulｄnoｔmａkｅａｂig 0.2. Howevｅｒ, ｉf the sheａｒwallｓheａr sｐａｎｒatiｏof ｌess than two couｐlinｇｂeａms sｐan of ｌeｓs than ２．5, then the shear coｍｐres ｓiｏn rａｔiｏis noｔgreaｔer thａn 0.15. Thｅｏther haｎｄ，ｔhe bｏttom oｆthe fraｍe ｓhｅar walｌstructure ｔo enhａnce tｈｅdｅsign sｈould ｎoｔbe leｓs thaｎ２０0mmａnd noｔlesｓthaｎstorey 1/１6，othｅｒｐaｒtｓｓhｏulｄnot be lｅss than 160mm ａnd ｎｏt ｌｅss thaｎｓtoｒey １/20. Arounｄthe wall of the frame ｓhｅar ｗall strucｔure sｈｏulｄbe set ｔo the beａm or dark bｅamａnd the sｉｄe columｎｔｏform a borｄｅr. Ｈoｒizｏntａl ｄｉｓtrｉbuｔioｎoｆsｈear waｌls cａn from the sheａr effect，tｈｉs design wｈen ｂuilｄｉng higｈｅr longeｒor fｒaｍｅｓtructｕre reinfoｒcｅment shｏuld be aｐprｏpｒiatelｙincｒeａｓed, ｅspｅcｉａlｌy in the sｅnｓitivｅｐarts of the beam pｏsition ｏr teｍperaｔuｒe, stiffnｅsｓchａnge is besｔappｒopriatｅly increased, ｔｈeｎcｏnsidｅration sｈoulｄbe ｇｉveｎｔo the wａlｌvertｉcaｌreiｎforｃemeｎt,becaｕse ｉt is mａinly fｒom the bｅnding efｆecｔ, aｎｄtake in ｓome ｍｕlti-ｓtorｅｙshｅａｒｗａll structuｒereinforcｅｄreｉnｆorceｍent rate -likｅlｅsｓconｓtｒained edgｅｏｆｔhｅcomｐonent or components reinforｃemeｎt of thｅedge ｃomｐｏnent.Referｅnces: [1 sad Hａyaｓhi,He Yaming. Ｏn the shorｔshｅar ｗall ｈigh-riｓe bｕilｄinｇｄesign ［J]．Kｅｙｕaｎ, 2008, (O2).高层框架剪力墙结构设计吴继成摘要: 本文从框架剪力墙结构设计的基本概念人手, 分析了框架剪力墙的构造设计内容, 包括抗震墙、剪跨比等的设计, 并出混凝土结构中最常用的框架剪力墙结构设计的注意要点。

毕业设计外文资料翻译题目甲醇氧化生产甲醛的银催化剂改性学院化学化工学院专业化学工程与工艺班级0803学生许继盟学号20080207167指导教师倪献智二〇一二年三月十五日Catalysts Today, 1996, (28): 239-244.甲醇氧化生产甲醛的银催化剂的改性A.N.Pestryakov摘 要 银催化剂的性能可用Zr ，La ， Rb ，C s 的氧化物改性，改性后的银催化剂的物化性能和催化性能已在甲醇的选择性氧化工艺中研究过，甲醇氧化制甲醛工艺中，质量分数为1%-10%的改性添加物会改变载体银的有效电荷及氧化还原性能、金属分散度和其表面扩散、催化剂表面酸度及结焦程度。

当银催化性能改变时，改性物主要影响催化剂活性位（++δn Ag Ag）。

关键词 银催化剂；甲醇氧化为甲醛 1 简介甲醇选择性氧化生产甲醛工艺中使用大量的载体银催化剂[1-3]。

采用不同的非有机添加物对银催化剂进行改性是提高其性能的最有前景的方法之一。

在银催化剂发现之后，人们致力于对其进行改进，以达到提高其催化活性和寿命，降低银使用量和扩展其工艺操作条件的目的。

广泛使用载体以减少银使用量及防止银在“严酷”条件（600-700 ℃）下烧结也是改性方法之一。

但是载体的堆积有限，不同改性化合物的少量添加（质量分数0.1-10%）可以使银可变的催化性能产生较大差异。

在科技和专利文献中提到过很多不同的添加物，它们能改善并激发银的催化性能[3-14]。

在这其中，研究人员提到改性作用的不同机理：银上金属的电子功能和电子密度改变[7-9]，O 2吸附的差异[3,10]，催化剂表面酸度[11]，催化剂表面的机械堵塞[12]，添加物的固有催化性质[13,14]。

然而，所有这些仅描述了催化剂改性的几个分散的方面，并没有涉及添加物对银催化剂改性影响的差异。

也没有考虑改性物对银催化剂活性位电子状态的影响。

在本文中，我们研究了改性物对银的性能影响的几个方面[15-18]，目的是在甲醇氧化制甲醛工艺中对稀有和稀土金属氧化物反应及银催化剂的电子属性、物化属性和催化属性进行综合研究。

毕业设计外文资料翻译学院：信息科学与工程学院专业：软件工程姓名： XXXXX学号： XXXXXXXXX外文出处： Think In Java (用外文写)附件： 1.外文资料翻译译文；2.外文原文。

附件1：外文资料翻译译文网络编程历史上的网络编程都倾向于困难、复杂，而且极易出错。

程序员必须掌握与网络有关的大量细节，有时甚至要对硬件有深刻的认识。

一般地，我们需要理解连网协议中不同的“层”（Layer）。

而且对于每个连网库，一般都包含了数量众多的函数，分别涉及信息块的连接、打包和拆包；这些块的来回运输；以及握手等等。

这是一项令人痛苦的工作。

但是，连网本身的概念并不是很难。

我们想获得位于其他地方某台机器上的信息，并把它们移到这儿；或者相反。

这与读写文件非常相似，只是文件存在于远程机器上，而且远程机器有权决定如何处理我们请求或者发送的数据。

Java最出色的一个地方就是它的“无痛苦连网”概念。

有关连网的基层细节已被尽可能地提取出去，并隐藏在JVM以及Java的本机安装系统里进行控制。

我们使用的编程模型是一个文件的模型；事实上，网络连接（一个“套接字”）已被封装到系统对象里，所以可象对其他数据流那样采用同样的方法调用。

除此以外，在我们处理另一个连网问题——同时控制多个网络连接——的时候，Java内建的多线程机制也是十分方便的。

本章将用一系列易懂的例子解释Java的连网支持。

15.1 机器的标识当然，为了分辨来自别处的一台机器，以及为了保证自己连接的是希望的那台机器，必须有一种机制能独一无二地标识出网络内的每台机器。

早期网络只解决了如何在本地网络环境中为机器提供唯一的名字。

但Java面向的是整个因特网，这要求用一种机制对来自世界各地的机器进行标识。

为达到这个目的，我们采用了IP（互联网地址）的概念。

IP以两种形式存在着：(1) 大家最熟悉的DNS（域名服务）形式。

我自己的域名是。

所以假定我在自己的域内有一台名为Opus的计算机，它的域名就可以是。