螺钉英文名称

关于螺丝词汇的中英文对照六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮缘螺帽HEX FLANGE NUTS高脚螺帽HEX COUPLING NUTS(HIGH NUTS)圆螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮壳螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS耐候钢六角重型螺帽CORTEN STEEL HEAVY HEX NUTS焊接螺帽WELD NUTS高张力螺帽HEIGH STRENGTH NUTS建业用螺帽STRUCTURAL NUTS不锈钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS铝螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEAVY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS 壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS铁盖+尼龙圈组合盖帽DIN 986 DOMED CAP NUTS突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLAT WASER NUTS六角割沟螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自动防松螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS不锈钢六角重型螺帽STAINLESS STEEL HEAVY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS普通六角螺帽HEX NUTS六角重型螺帽HEAVY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺丝用六角螺帽HEX MACHINE SCREW NUT灯饰英语词汇（二）2010-03-04 15:44:36 阅读15 评论0 字号：大中小一、灯具种类词汇Bollard lamp (高度及腰的）柱灯Ceiling fan 天花风扇Ceiling Lamp 天花灯Chandelier 枝形吊灯Clip-on lamp 夹灯Desk lamp 功能性台灯Down light 向下照的灯Flash light 手电筒Flood light 泛光灯Floor lamp 座地灯Garden light 花园灯Hard wires 固定装置灯具Lighting fixtures 灯具（美）Luminaire 灯具（欧）Night light 夜灯Pendant lamp 吊灯Picture light 照亮书像用的灯Pole lamp （高度过头的）柱灯Portable lamps 可移动灯具Reading light 看书用的灯Recessed lamp (天花）内置式灯Spot light 聚光灯Swing arm lamp 摇臂灯Table lamp 非功能性台灯Task light 工作灯Tiffany 彩色玻璃片拼成灯罩的灯Torch 火炬形灯；手电筒Torchiere 向天花照的灯Track head 轨道灯（指不连轨道的灯具头部）Track light 轨道灯Up light 向上照的灯Vanity 浴室用灯Wall lamp 壁灯二、灯具常用零部件1、一般结构件Alum-oxidized reflector 铝氧化反光杯Arm post 丫叉Arm 灯臂（平行于地面者）Balance block 底座配重Balance steel 平衡线Ball Jointer 波接头Barrier 隔离罩（美）（防止灯具的破碎部份射出用，例如石英灯的玻璃片/罩）Base bottom 底座底Base top 底座面Base 底座Battery cover 电池盖Bracket 支架Cast iron 铸铁Clamp 螺栓夹（夹紧力由螺栓提供，力度较大）Clip 弹簧夹（夹紧力由弹簧提供，力度较小）Connect plate 连接片Ceiling 天花板Decorative part 装饰件Decorative ring 装饰环Enclosure 罩壳（指包容及保护带电体之类的外壳）Eyeball 牛眼Eyelet 鸡眼Filter 滤光镜（例如，过滤紫外光的镜片为UV filter)Finial 尖顶形装饰，有时兼具螺母的功能Flexible stem 软喉（欧）Front shade 前罩Gooseneck 软喉（美）Grid guard 防护网Guard 防护罩（防止人手接触灯具的某部份用，例如：Torchiere的铁丝钢罩）Handle 手柄（反光杯很汤，有时装有手柄作调整握持用，有时兼作防上灯具头接触可燃物的间隔（spacer)用。

木炭机知识1 GB/T 2-1985 紧固件外螺纹零件的末端Fasteners--Ends of parts with external thread2 GB/T 8-1988 方头螺栓C级Square head bolts--Product grade C3 GB/T 10-1988 沉头方颈螺栓Flat countersunk square neck bolts4 GB/T 11-1988 沉头带榫螺栓Flat countersunk nib bolts5 GB/T 12-1988 半圆头方颈螺栓Cup head square neck bolts6 GB/T 13-1988 半圆头带榫螺栓Cup head nib bolts7 GB/T 15-1988 大半圆头带榫螺栓Cup head nib bolts with large head8 GB/T 22-1976 小六角头导颈螺栓Bolts, small hexagon head with fit neck9 GB/T 23-1976 小六角头螺杆带孔螺栓Bolts, small hexagon head with hole through the shank10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓Bolts, small hexagon head with fit neck and hole through the shank11 GB/T 25-1976 小六角头头部带孔螺栓Bolts, small hexagon head with holes through the head12 GB/T 26-1976 小六角头头部带孔导颈螺栓Bolts, small hexagon head with fit neck and holes through the head13 GB/T 27-1988 六角头铰制孔用螺栓A和B级Hexagon fit bolts--Product grade A and B14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓A和B级Hexagon fit bolts with Split pin hole on shank--Product grade A and B15 GB/T 29.1-1988 六角头头部带槽螺栓A和B级Hexagon bolts with slot on head--Product grade A and B16 GB/T 29.2-1988 十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation17 GB/T 31.1-1988 六角头螺杆带孔螺栓A和B级Hexagon bolts with split pin hole on shank--Product grade A and B18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆B级Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B19 GB/T 31.3-1988 六角头螺杆带孔螺栓细牙A和B级Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B20 GB/T 32.1-1988 六角头头部带孔螺栓A和B级Hexagon bolts with wire holes on head--Product grade A and B21 GB/T 32.2-1988 六角头头部带孔螺栓细杆B级Hexagon bolts with wire holes on head--Reduced shank--Product grade B22 GB/T 32.3-1988 六角头头部带孔螺栓细牙A和B级Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B23 GB/T 35-1988 小方头螺栓B级Square head bolts with small head--Product grade B24 GB/T 37-1988 T型槽用螺栓Bolts for T-Slot25 GB/T 38-1976 螺栓技术条件Bolts--Technical requirements26 GB/T 39-1988 方螺母C 级Square nuts--Product grade C27 GB/T 41-1986 1 型六角螺母C 级Hexagon nuts--Style 1--Product grad C28 GB/T 56-1988 六角厚螺母Hexagon thick nuts29 GB/T 61-1976 螺母技术条件Nuts--Technical requirements30 GB/T 62-1988 蝶形螺母Wing nuts31 GB/T 63-1988 环形螺母Lifting nuts32 GB/T 65-1985 开槽圆柱头螺钉Slotted cheese head screws33 GB/T 67-1985 开槽盘头螺钉Slotted pan head screws34 GB/T 68-1985 开槽沉头螺钉Slotted countersunk head screws35 GB/T 69-1985 开槽半沉头螺钉Slotted raised countersunk head screws36 GB/T 70-1985 内六角圆柱头螺钉Hexagon socket cap head screws37 GB/T 71-1985 开槽锥端紧定螺钉Slotted set screws with cone point38 GB/T 72-1988 开槽锥端定位螺钉Slotted set screws with cone point39 GB/T 73-1985 开槽平端紧定螺钉Slotted set screws with flat point40 GB/T 74-1985 开槽凹端紧定螺钉Slotted set screws with cup point41 GB/T 75-1985 开槽长圆柱端紧定螺钉Slotted set screws withlong dog point42 GB/T 77-1985 内六角平端紧定螺钉Hexagon socket set screws with flat point43 GB/T 78-1985 内六角锥端紧定螺钉Hexagon socket set screws with cone point44 GB/T 79-1985 内六角圆柱端紧定螺钉Hexagon socket set screws with dog point45 GB/T 80-1985 内六角凹端紧定螺钉Hexagon socket set screws with cup point46 GB/T 83-1988 方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end47 GB/T 84-1988 方头凹端紧定螺钉Square set screws with cup point48 GB/T 85-1988 方头长圆柱端紧定螺钉Square set screws with long dog point49 GB/T 86-1988 方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end50 GB/T 89-1976 螺钉技术条件Screws--Technical requirements51 GB/T 90-1985 紧固件验收检查、标志与包装Acceptance inspection,marking and packaging of fasteners52 GB/T 91-1986 开口销Split pins53 GB/T 93-1987 标准型弹簧垫圈Single coil spring lock washers--Normal type54 GB/T 94.1-1987 弹性垫圈技术条件弹簧垫圈Specifications for spring washers--Single coil spring lock washers55 GB/T 94.2-1987 弹性垫圈技术条件齿形、锯齿锁紧垫圈Specifications for spring washers--Toothed lock and serrated lock washers56 GB/T 94.3-1987 弹性垫圈技术条件鞍形、波形弹性垫圈Specifications for spring washers--Curved and wave spring washers57 GB/T 95-1985 平垫圈-C级Plain washers--Product grade C58 GB/T 272-1993 滚动轴承代号方法Rolling bearing--Identification code59 GB/T 273.1-1987 滚动轴承圆锥滚子轴承外形尺寸方案Rolling bearings Tapered roller bearings--Boundary dimensions60 GB/T 273.3-1988 滚动轴承向心轴承外形尺寸方案Rolling bearings Radial bearings-Boundary dimensions61 GB/T 274-1991 滚动轴承装配倒角极限Rollingbearing chamfer dimension limits62 GB/T 275-1993 滚动轴承与轴和外壳的配合Shaft and housing fits for rolling bearings63 GB/T 276-1994 滚动轴承深沟球轴承外形尺寸Rolling bearings--Deep groove ball bearings--Boundary dimensions64 GB/T 280-1964 带毡封圈的单列向心球轴承结构型式和基本尺寸Rolling bearings--Single-row radial ball bearings withfelt seals--Types and basic dimensions65 GB/T 281-1994 滚动轴承调心球轴承外形尺寸Rolling bearings--Self-aligning ball bearings--Boundary dimensions66 GB/T 283-1994 滚动轴承圆柱滚子轴承外形尺寸Rolling bearings--Cylindrical roller bearings-Boundary dimensions67 GB/T 285-1994 滚动轴承双列圆柱滚子轴承外形尺寸Rolling bearings--Double row cylindrical roller bearings-Boundary dimensions68 GB/T 286-1964 双列向心球面滚子轴承结构型式和基本尺寸Rolling bearings--Double -row radial spherical roller bearings--Types and basic dimensions69 GB/T 288-1994 滚动轴承调心滚子轴承外形尺寸Rolling bearings--Self-aligning roller bearings-Boundary dimensions70 GB/T 289-1964 滚针轴承结构型式和基本尺寸Needle roller bearings--Types and basic dimensions71 GB/T 291-1964 螺旋滚子轴承结构型式和基本尺寸Rolling bearings with helically wound cylindrical rollers--Types and basic dimensions72 GB/T 292-1994 滚动轴承角接触球轴承外形尺寸Rolling bearings--Angular contact ball bearings--Boundary dimensions73 GB/T 294-1994 滚动轴承三点和四点接触球轴承外形尺寸Rolling bearings--Three point and four point contact ball bearings--Boundary dimensions74 GB/T 296-1994 滚动轴承双列角接触球轴承外形尺寸Rolling bearings--Double row angular contact ballbearings--Boundary dimensions75 GB/T 297-1994 滚动轴承圆锥滚子轴承外形尺寸Rolling bearings--Tapered roller bearings--Boundary dimensions76 GB/T 299-1995 滚动轴承双列圆锥滚子轴承外形尺寸Rolling bearings--Metric double row tapered roller bearings--Boundary dimensions77 GB/T 300-1995 滚动轴承四列圆锥滚子轴承外形尺寸Rolling bearings--Four row tapered roller bearings--Boundary dimensions78 GB/T 301-1995 滚动轴承推力球轴承外形尺寸Rolling bearings--Thrust ball bearings--Boundary dimensions79 GB/T 304.1-1988 关节轴承分类Spherical plain bearings Classification80 GB/T 304.2-1988 关节轴承代号方法Spherical plain bearings Identification code81 GB/T 304.3-1990 关节轴承配合Spherical plain bearings-Fits82 GB/T 304.9-1981 向心关节轴承技术条件Spherical plain radial bearings, joint type--Technical requirements83 GB/T 304.10-1989 关节轴承公差Spherical plain bearings-Tolerances84 GB/T 307.1-1994 滚动轴承向心轴承公差Rolling bearings--Radial bearings--Tolerances85 GB/T 307.2-1995 滚动轴承测量和检验的原则及方法Rolling bearings--Measuring and gauging principles and methods86 GB/T 307.3-1996 滚动轴承通用技术规则Rolling bearings--General technical regulations87 GB/T 307.4-1994 滚动轴承推力球轴承公差Rolling bearings--Thrust ball bearings--Tolerances88 GB/T 308-1989 滚动轴承钢球Rolling bearings-Steel balls89 GB/T 309-1984 滚动轴承滚针Rolling bearings--Needle rollers90 GB/T 794-1993 加强半圆头方颈螺栓Strengthened cap head square neck bolts91 GB/T 798-1988 活节螺栓Eye bolts92 GB/T 799-1988 地脚螺栓Eyelet bolts93 GB/T 800-1988 沉头双榫螺栓Flat countersunk double nib bolts94GB/T 802-1988 组合式盖形螺母Acorn nuts95 GB/T 804-1988 球面六角螺母Hexagon nuts with raised face96 GB/T 805-1988 扣紧螺母Tight nuts97 GB/T 806-1988 滚花高螺母Knurled nut with collar98 GB/T 807-1988 滚花薄螺母Knurled nuts99 GB/T 808-1988 小六角特扁细牙螺母Small hexagon thin nuts-Fine pitch thread100 GB/T 809-1988 嵌装圆螺母Insert round nuts101 GB/T 810-1988 小圆螺母Small round nuts102 GB/T 812-1988 圆螺母Round nuts103 GB/T 815-1988 端面带孔圆螺母Round nuts with drilled holes in one face104 GB/T 816-1988 侧面带孔圆螺母Round nuts with set pin holes in side105 GB/T 817-1988 带槽圆螺母Slotted round nuts106 GB/T 818-1985 十字槽盘头螺钉Cross recessed pan head screws107 GB/T 819-1985 十字槽沉头螺钉Cross recessed countersunk head screws108 GB/T 820-1985 十字槽半沉头螺钉Cross recessed raised countersunk head screws109 GB/T 821-1988 方头倒角端紧定螺钉Square set screws with chamfered end110 GB/T 822-1988 十字槽圆柱头螺钉Cross recessed cheese head serews111 GB/T 823-1988 十字槽小盘头螺钉Cross recessed small pan head screws112 GB/T 824-1976 圆柱头内花键螺钉Screws,fluted socket head113 GB/T 825-1988 吊环螺钉Eyebolts114 GB/T 827-1986 标牌铆钉Rivets for name plate115 GB/T 828-1988 开槽盘头定位螺钉Slotted pan head set setscrews with dog point116 GB/T 829-1988 开槽圆柱端定位螺钉Slotted setscrews with dog point117 GB/T 830-1988 开槽圆柱头轴位螺钉Slotted cheese head screws with shoulder118 GB/T 831-1988 开槽无头轴位螺钉Slotted shoulder screws119 GB/T 832-1988 开槽带孔球面圆柱头螺钉Slotted capstan screws120 GB/T 833-1988 开槽大圆柱头螺钉121 GB/T 834-1988 滚花高头螺钉Knurled thumb screws 122 GB/T 835-1988 滚花平头螺钉Knurled screws 123 GB/T 836-1988 滚花小头螺钉Knurled screws with small head 124 GB/T 837-1988 开槽盘头不脱出螺钉Slotted pan head screws with waisted shank 125 GB/T 838-1988 六角头不脱出螺钉Hexagon screws with waisted shank 126 GB/T 839-1988 滚花头不脱出螺钉Knurled thumb screws with waisted shank 127 GB/T 840-1988 塑料滚花头螺钉Plastic diamond knurlhead screws 128 GB/T 845-1985 十字槽盘头自攻螺钉Cross recessed pan head tapping screws 129 GB/T 846-1985 十字槽沉头自攻螺钉Cross recessed countersunk head tapping screws 130 GB/T 847-1985 十字槽半沉头自攻螺钉Cross recessed raised countersunk head tapping screws 131 GB/T 848-1985 小垫圈--A级Plain washers--Small series--Product grade A 132 GB/T 849-1988 球面垫圈Weshers with ball face 133 GB/T 850-1988 锥面垫圈Washers with cone face 134 GB/T 851-1988 开口垫圈Washers with split 135 GB/T 852-1988 工字钢用方斜垫圈Square taper washers for I section 136 GB/T 853-1988 槽钢用方斜垫圈Square taper washers for slot section 137 GB/T 854-1988 单耳止动垫圈Tab washers with long tab 138 GB/T 855-1988 双耳止动垫圈Tab washers with long tab and wing 139 GB/T 856-1988 外舌止动垫圈External tab washers 140 GB/T 858-1988 圆螺母用止动垫圈Tab washers for round nut 141 GB/T 859-1987 轻型弹簧垫圈Single coil spring lock washers,Light type 142 GB/T 860-1987 鞍形弹性垫圈Curved spring washers 143 GB/T 861.1-1987 内齿锁紧垫圈Lock washers internal teeth 144 GB/T 861.2-1987 内锯齿锁紧垫圈Serrated lock washers internal teeth 145 GB/T 862.1-1987 外齿锁紧垫圈Lock washers external teeth 146 GB/T 862.2-1987 外锯齿锁紧垫圈Serrated lock washers external teeth 147 GB/T 863.1-1986 半圆头铆钉(粗制) Round head rivets--Black 148 GB/T 863.2-1986 小半圆头铆钉(粗制) Round head rivets with small head--Black 149 GB/T 864-1986 平锥头铆钉(粗制) Cone head rivets--Black 150 GB/T 865-1986 沉头铆钉(粗制) Countersunk head rivets-Black 151 GB/T 866-1986 半沉头铆钉(粗制) Oval countersunk head rivets--Black 152 GB/T 867-1986 半圆头铆钉Round head rivets 153 GB/T 868-1986 平锥头铆钉Cone head rivets 154 GB/T 869-1986 沉头铆钉Countersunk head rivets 155 GB/T 870-1986 半沉头铆钉Oval countersunk head rivets 156 GB/T 871-1986 扁圆头铆钉Flat round head rivets 157 GB/T 872-1986 扁平头铆钉Thin head rivets 158 GB/T 873-1986 扁圆头半空心铆钉Oval head semi-tubular rivets 159 GB/T 874-1986 120°沉头半空心铆钉120 degree countersunk head semi-tubular rivets 160 GB/T 875-1986 偏平头半空心铆钉Thin head semi-tubular rivet 161 GB/T 876-1986 空心铆钉Tubular rivets 162 GB/T 877-1986 开尾圆锥销Taper pins with split 163 GB/T 878-1986 螺纹圆柱销Parallel pins with external thread 164 GB/T 879-1986 弹性圆柱销Spring-type straight pins—Slotted 165 GB/T 880-1986 带孔销Pins with split pin hole 166 GB/T 881-1986 螺尾锥销Taper pins with external thread 167 GB/T 882-1986 销轴Clevis pins with head 168 GB/T 883-1986 锥销锁紧挡圈Lock rings with cone pin 169 GB/T 884-1986 螺钉锁紧挡圈Lock ring with screw 170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈Lock rings with screw and circlip 171 GB/T 886-1986 轴肩挡圈Rings for shoulder 172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts (with non-metallic insert),style 1 173 GB/T 891-1986 螺钉紧固轴端挡圈Lock rings at the end of shaft with screw 174 GB/T 892-1986 螺栓紧固轴端挡圈Lock rings at the end of shaft with bolt 175 GB/T 893.1-1986 孔用弹性挡圈--A型Circlips for holes--Type A 176 GB/T 893.2-1986 孔用弹性挡圈--B型Circlips for hole--Type B 177 GB/T 894.1-1986 轴用弹性挡圈--A型Circlips for shaft--Type A 178 GB/T 894.2-1986 轴用弹性挡圈--B型Circlips for shaft--Type B 179 GB/T 895.1-1986 孔用钢丝挡圈Roundwire snap rings for hole 180 GB/T 895.2-1986 轴用钢丝挡圈Roundwire snap rings for shaft 181 GB/T 896-1986 开口挡圈"E" rings 182 GB/T 897-1988 双头螺柱bm=1d Double end studs--bm=1d 183 GB/T 898-1988 双头螺柱bm=1.25d Double end studs bm=1.25d 184 GB/T 899-1988 双头螺柱bm=1.5d Double end studs bm=1.5d 185 GB/T 900-1988 双头螺柱bm=2d Double end studs bm=2d 186 GB/T 901-1988 等长双头螺柱B级Double end studs (clamping type)--Product grade B 187 GB/T 902.1-1989 手工焊用焊接螺柱Weld studs for manual welding 188 GB/T 902.2-1989 机动弧焊用焊接螺柱Weld studs for arc welding 189 GB/T 902.3-1989 储能焊用焊接螺柱Weld studs for capacitor discharge welding 190 GB/T 921-1986 钢丝锁圈Round wire circlips 191 GB/T 922-1986 木螺钉技术条件Specifications for wood screws 192 GB/T 923-1988 盖形螺母Acorn nuts 193 GB/T 925-1988 轻型六角自锁螺母Self-locking nuts,hexagon light 194 GB/T 927-1988 球面六角自锁螺母Self-locking nuts,hexagon sphere 195 GB/T 929-1988 单耳托板自锁螺母Self-locking nuts,singlelug, anchor 196 GB/T 930-1988 双耳托板自锁螺母Self-locking nuts,twolug, anchor 197 GB/T 931-1988 角形托板自锁螺母Self-locking nuts,angle, anchor 198 GB/T 932-1988 气密单耳托板自锁螺母Self-locking nuts,singlelug, anchor, sealing, 199 GB/T 933-1988 气密双耳托板自锁螺母Self-locking nuts,twolug, anchor, sealing 200 GB/T 937-1988 成组游动托板自锁螺母Self-locking nuts, anchor, floating,Gang channel 201 GB/T 938-1988 游动自锁螺母Self-locking nuts, floating 202 GB/T 939-1988 单耳托板自锁螺母保护罩Boots for self-locking nuts, singlelug, anchor 203 GB/T 940-1988 双耳托板自锁螺母保护罩Boots for self-locking nuts,twolug, anchor 204 GB/T 941-1988 角形托板自锁螺母保护罩Boots for self-locking nuts,angle, anchor 205 GB/T 943-1988 自锁螺母技术条件Procurement specification for self-locking nuts 206 GB/T 945-1976 十字槽球面中柱头螺钉Screws,cross recessed,thin raised cheese head 207 GB/T 946-1988 开槽球面圆柱头轴位螺钉Slotted raised cheese head with shoulder 208 GB/T 947-1988 开槽球面大圆柱头螺钉Slotted large raised cheese head screws 209 GB/T 948-1988 开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank 210 GB/T 949-1988 开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank 211 GB/T 950-1986 十字槽圆头木螺钉Cross recessed round head wood screws 212 GB/T 951-1986 十字槽沉头木螺钉Cross recessed countersunk head wood screws 213 GB/T 952-1986 十字槽半沉头木螺钉Cross recessed raised countersunk head wood screws 214 GB/T 953-1988 等长双头螺柱C级Double end studs (clamping type)--Product grade C 215 GB/T 954-1986 120°沉头铆钉120°degree countersunk head rivets 216 GB/T 955-1987 波形弹性垫圈Wave spring washers 217 GB/T 956.1-1987 锥形锁紧垫圈Countersunk external toothed lock washers 218 GB/T 956.2-1987 锥形锯齿锁紧垫圈Countersunk serrated external toothed lock washers 219 GB/T 959.1-1986 挡圈技术条件--弹性挡圈Specifications for ring—Circlips 220 GB/T 959.2-1986 挡圈技术条件--钢丝挡圈Specifications for ring—Round wire snap rings 221 GB/T 959.3-1986 挡圈技术条件--切制挡圈Specifications for ring—Cutting rings 222 GB/T 960-1986 夹紧挡圈Grip rings 223 GB/T 961-1988 单耳托板自锁螺母垫片Spacers for self-locking nuts,singlelug, anchor 224 GB/T 962-1988 双耳托板自锁螺母垫片Spacers for self-locking nuts,twolug, anchor 225 GB/T 963-1988 角形托板自锁螺母垫片Spacers for self-locking nuts,angle, anchor 226 GB/T 973-1976 十字槽扁圆头螺钉Screws,cross recessed,oval head 227 GB/T 974-1976 十字槽120°半沉头螺钉Screws,cross recessed,120°raised countersunk head 228 GB/T 975-1986 管状铆钉Pipe type rivets 229 GB/T 1007-1976 小六角较扁螺母Small hexagon medium thin nuts 230 GB/T 1009-1978 螺母专用技术条件Specified specifications for nuts 231 GB/T 1011-1986 大扁圆头铆钉Truss head rivets 232 GB/T 1012-1986 120°半沉头铆钉120°degree oval countersunk rivets 233 GB/T 1013-1986 平锥头半空心铆钉Cone head semi-tubuler rivets234 GB/T 1014-1986 大扁圆头半空心铆钉Truss head semi-tubuar rivets 235 GB/T 1015-1986 沉头半空心铆钉Countersunk head semi-tublar rivets 236 GB/T 1016-1986 无头铆钉Headless rivets 237 GB/T 1017-1978 铆钉专用技术条件Specified specifications for rivets 238 GB/T 1021-1976 角形垂直单耳止动垫圈Lock washers with angular upturn tab perpendicular to the lug 239 GB/T 1022-1976 角形单耳止动垫圈Lock washers with angular upturn tab in line to the lug 240 GB/T 1023-1976 角形垂直外舌止动垫圈Lock washers with angular upturn tab perpendicular to the external tab241 GB/T 1024-1976 角形外舌止动垫圈Lock washers with angular upturn tab in line to the external tab 242 GB/T 1030-1988 内球面垫圈Inner sphere washers 243 GB/T 1047-1995 管道元件的公称通径Nominal size for pipe components 244 GB/T 1048-1990 管道元件公称压力Nominal pressure for pipe components 245 GB/T 1095-1979 平键键和键槽的剖面尺寸Parallel keys--Dimensions of cross sections and keyways 246 GB/T 1096-1979 普通平键型式尺寸Plain parallel keys--Types and dimensions 247 GB/T 1097-1979 导向平键型式尺寸Feather keys--Types and dimensions 248 GB/T 1098-1979 半圆键键和键槽的剖面尺寸Semi-circular (Woodruff) keys--Dimensions of cross sections and keyways 249 GB/T 1099-1979 半圆键型式尺寸Woodruff keys--Types and dimensions 250 GB/T 1144-1987 矩形花键尺寸、公差和检验Straight-sided spline—Dimensions tolerances and verification 251 GB/T 1168-1976 螺柱技术条件Studs--Technical requirements 252 GB/T 1228-1991 钢结构用高强度大六角头螺栓High strength bolts with large hexagon headfor steel structures 253 GB/T 1229-1991 钢结构用高强度大六角螺母High strength large hexagon nuts for steel structures 254 GB/T 1230-1991 钢结构用高强度垫圈High strength plain washers for steel structures 255 GB/T 1231-1991 钢结构用高强度大六角头螺拴、大六角螺母、垫圈技术条件Specifications of high strength bolts with large hexa-gon head, large hexagon nuts, plain washers for steel structures 256 GB/T 1237-1988 紧固件的标记方法Designation system for fasteners 257 GB/T 1337-1988 六角自锁螺母Self-locking nuts,hexagon 258 GB/T 1338-1988 小六角扁自锁螺母Self-locking nuts,reduced hexagon oblate 259 GB/T 1339-1988 小六角自锁螺母Self-locking nuts,reduced hexagon 260 GB/T 1340-1988 成组游动托板自锁螺母支架Supports for self-locking nuts,anchor floating,Gang channel 261 GB/T 1356-1988 淅开线圆柱齿轮基本齿廓Basic rack tooth profile of involute cylindrical gears 262 GB/T 1357-1987 渐开线圆柱齿轮模数Modules of involute cyindrical gears 263 GB/T 1563-1979 楔键键和键槽的剖面尺寸Taper keys--Cross section dimensions of keys and keyways 264 GB/T 1564-1979 普通楔键型式尺寸Taper keys for general use--Types and dimensions 265 GB/T 1565-1979 钩头楔键型式尺寸Gib-head taper keys--Types and dimensions 266 GB/T 1566-1979 薄型平键键和键槽的剖面尺寸Thin flat keys--Cross section dimensions and keyways 267 GB/T 1567-1979 薄型平键型式尺寸Thin flat keys--Types and dimensions 268 GB/T 1840-1989 圆弧圆柱齿轮模数Modules of cylindrical gear with circular arc profiles 269 GB/T 1974-1980 切向键及其键槽Tangential keys and keyways 270 GB/T 2362-1990 小模数渐开线圆柱齿轮基本齿廓Basic rack tooth profile of fine-pitch involute cylindrical gears 271 GB/T 2363-1990 小模数渐开线圆柱齿轮精度Accuracy of fine-pitch involute cylindrical gears 272 GB/T 2509-1981 滑动轴承铜合金整体轴套形式、尺寸与公差Copper alloy integrated shaft sleeves for plain bearings--Types, dimensions and tolerances 273 GB/T 2510-1981 滑动轴承铜合金带挡边整体轴套形式、尺寸与公差Copper alloy integrated shaft sleeves for plain bearings with gears--Types, dimensions and tolerances 274 GB/T 2511-1981 滑动轴承铜合金整体轴套技术条件Copper alloy integrated shaft sleeves--Technical requirements 275 GB/T 2555-1981 一般用途管法兰连接尺寸Pipe flange connectors for ordinary use--Mounting dimensions 276 GB/T 2556-1981 一般用途管法兰密封面形状和尺寸Pipe flanges for ordinary use--Sealing surfaces--Forms and dimensions 277 GB/T 2672-1986 内六角花形盘头螺钉Hexagon lobular socket pan head screws 278 GB/T 2673-1986 内六角花形沉头螺钉Hexagon lobular socket countersunk head screws 279 GB/T 2674-1986 内六角花形半沉头螺钉Hexagon lobular socket raised countersunk head screws 280 GB/T 2685-1981 滑动轴承粉末冶金筒形轴承型式、尺寸与公差Powder metallurgy plain bearing--Cylindrical type--Types, dimensions and tolerances 281 GB/T 2686-1981 滑动轴承粉末冶金带挡边筒形轴承型式、尺寸与公差Powder metallurgy plain bearing--Rimed cylindrical type--Types, dimensions and tolerances 282 GB/T 2687-1981 滑动轴承粉末冶金球形轴承型式、尺寸与公差Powder metallurgy plain bearing--Spherical type--Types, dimensions and tolerances 283 GB/T 2688-1981 滑动轴承粉末冶金轴承技术条件Powder metallurgy plain bearing--Technical requirements 284 GB/T 2821-1992 齿轮几何要素代号Symbols for gear geometrical data 285 GB/T 2889-1994 滑动轴承术语Plain bearings--Terms, definitions and classification 286 GB/T 3098.1-1982 紧固件机械性能螺栓、螺钉和螺柱Mechanical properties of fasteners--Bolts, screws and studs 287 GB/T 3098.2-1982 紧固件机械性能螺母Mechanical properties of fasteners--Nuts 288 GB/T 3098.3-1982 紧固件机械性能紧定螺钉Mechanical properties of fasteners--Set screws 289 GB/T 3098.4-1986 紧固件机械性能--细牙螺母Mechanical properties of fasteners--Nuts with fine pitch thread 290 GB/T 3098.5-1985 紧固件机械性能自攻螺钉Mechanical properties of fasteners--Tapping screws 291 GB/T 3098.6-1986 紧固件机械性能不锈钢螺栓, 螺钉, 螺柱和螺母Mechanical properties of fasteners--Stainless steel bolts,screws, studs and nuts 292 GB/T 3098.7-1986 紧固件机械性能自攻锁紧螺钉粗牙普通螺纹系列Mechanical properties of fasteners--Thread forming screws--Metric coarse thread series 293 GB/T 3098.8-1992 紧固件机械性能耐热用螺纹连接副Mechanical properties of fasteners--Components for bolted connections made mainly from materials with a high temperature strength 294 GB/T 3098.9-1993 紧固件机械性能有效力矩型钢六角锁紧螺母Mechanical properties of fasteners--Prevailing torque type steel hexagon nuts 295 GB/T 3098.10 -1993 紧固件机械性能有色金属制造的螺栓、螺钉、螺柱和螺母Mechanical properties of fasteners-- Bolts, screws, studs and nuts made of non-ferrous metals 296 GB/T 3098.11-1995 紧固件机械性能自钻自攻螺钉Mechanicalproperties of fasteners--Self-drilling tapping screws 297 GB/T 3098.13-1996 紧固件机械性能螺栓与螺钉的扭矩试验和破坏扭矩公称直径1~10mm Mechanical properties of fasteners--Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm 298 GB/T 3098.12-1996 紧固件机械性能螺母锥形保证载荷试验Mechanical properties of fasteners--Cone proof load test on nuts 299 GB/T 3099-1982 螺栓、螺钉、螺母及附件名词术语Bolts, screws, nuts and accessories--Terminology and nomenclature 300 GB/T 3103.1-1982 紧固件公差螺栓、螺钉和螺母Tolerances for fasteners--Bolts, screws and nuts 301 GB/T 3103.2-1982 紧固件公差用于精密机械的螺栓、螺钉和螺母Tolerances for fasteners--Bolts, screws and nuts for fine mechanics 302 GB/T 3103.3-1982 紧固件公差平垫圈Tolerances for fasteners--Washers 303 GB/T 3103.4-1992 紧固件公差耐热用螺纹连接副Tolerances for fasteners--Components for bolted connections made mainly from materials with a high temperature strength 304 GB/T 3104-1982 紧固件六角产品的对边宽度Fasteners--Widths across flats of hexagon products 305 GB/T 3105-1982 螺栓和螺钉的头下圆角半径Radii under the head of bolts and screws 306 GB/T 3106-1982 螺栓、螺钉和螺柱的公称长度和普通螺栓的螺纹长度Bolts, screws and studs--Nominal lengths, and thread lengths for general purpose bolts 307 GB/T 3162-1991 滑动轴承薄壁轴瓦尺寸、结构要素与公差Plain bearings—Thin-walled bearing shells—Dimensions, structure elements and tolerances 308 GB/T 3287-1982 可锻铸铁管路连接件技术条件Technical requirements of malleable cast iron pipefittings 309 GB/T 3288-1982 可锻铸铁管路连接件验收规则Delivery requirements of malleable cast iron pipe fittings 310 GB/T 3289.1-1982 可锻铸铁管路连接件型式尺寸管件结构尺寸表Malleable cast iron pipe fittings--Type size--Dimensions list of pipe fittings structure 311 GB/T 3289.2-1982 可锻铸铁管路连接件型式尺寸弯头内外丝弯头Malleable cast iron pipe fittings--Type size--Elbows male and female elbows 312 GB/T 3289.3-1982 可锻铸铁管路连接件型式尺寸45°弯头45°内外丝弯头Malleable cast iron pipe fittings--Type size--Elbows 45°, male and female elbows 45° 313 GB/T 3289.4-1982 可锻铸铁管路连接件型式尺寸异径弯头Malleable cast iron pipe fittings--Type size--Reducing elbows 314 GB/T 3289.5-1982 可锻铸铁管路连接件型式尺寸异径内外丝弯头Malleable cast iron pipe fittings--Type size--Male and female reducing elbows 315 GB/T 3289.6-1982 可锻铸铁管路连接件型式尺寸侧孔弯头Malleable cast iron pipe fittings--Type size--Side outlet elbows 316 GB/T 3289.7 -1982 可锻铸铁管路连接件型式尺寸月弯内外丝月弯外丝月弯Malleable cast iron pipe fittings-- Type size--Return bends, male and female return bends, thread return bends 317 GB/T 3289.8-1982 可锻铸铁管路连接件型式尺寸45°月弯45°内外丝月弯45°外丝月弯Malleable cast iron pipe fittings--Type size--Long sweep bends 45°，male and female long sweep bends 45°,male long sweep bends 45° 318 GB/T 3289.9-1982 可锻铸铁管路连接件型式尺寸U型弯头Malleable cast iron pipe fittings--Type size--U-Elbows(return bends) 319 GB/T 3289.10-1982 可锻铸铁管路连接件型式尺寸三通内外丝三通Malleable cast iron pipe fittings--Type size--Tees, male and female tees 320 GB/T 3289.11-1982 可锻铸铁管路连接件型式尺寸异径内外丝三通Malleable cast iron pipe fittings--Type size--Male and female reducing tees 321 GB/T 3289.12-1982 可锻铸铁管路连接件型式尺寸中大异径三通Malleable cast iron pipe fittings--Type size--Medium-large reducing tees [tees(increasing on the branch)] 322 GB/T 3289.13-1982 可锻铸铁管路连接件型式尺寸侧大异径三通Malleable cast iron pipe fittings--Type size--Lateral-large reducing tees 323 GB/T 3289.14-1982 可锻铸铁管路连接件型式尺寸中小异径三通Malleable cast iron pipe fittings--Type size--Medium-less reducing tees 324 GB/T 3289.15-1982 可锻铸铁管路连接件型式尺寸侧小异径三通Malleable cast iron pipe fittings--Type size--Lateral-less reducing tees 325 GB/T 3289.16-1982 可锻铸铁管路连接件型式尺寸中小偏心异径三通Malleable cast iron pipe fittings--Type size--Medium-less eccentric reducing tees 326 GB/T 3289.17-1982 可锻铸铁管路连接件型式尺寸45°三通Y型三通Malleable cast iron pipe fittings--Type size--Tees45°, Y pieces(tees) 327 GB/T 3289.18-1982 可锻铸铁管路连接件型式尺寸Y型异径三通Malleable cast iron pipe fittings--Type size--Y Piece reducing(tees) 328 GB/T 3289.19-1982 可锻铸铁管路连接件型式尺寸侧孔三通Malleable cast iron pipe fittings--Type size--Side outlet tees 329 GB/T 3289.20-1982 可锻铸铁管路连接件型式尺寸四通Malleable cast iron pipe fittings--Type size--Crosses 330 GB/T 3289.21-1982 可锻铸铁管路连接件型式尺寸异径四通Malleable cast iron pipe fittings--Type size--Reducing crosses 331 GB/T 3289.22-1982 可锻铸铁管路连接件型式尺寸外接头内外丝接头Malleable cast iron pipe fittings--Type size--Male joints(sockets), male and female joints (sockets) 332 GB/T 3289.23-1982 可锻铸铁管路连接件型式尺寸无方内接头Malleable cast iron pipe fittings--Type size--No-square inner joint (nipples) 333 GB/T 3289.24-1982 可锻铸铁管路连接件型式尺寸异径外接头Malleable cast iron pipe fittings--Type size--Reducing male joints (sockets) 334 GB/T 3289.25-1982 可锻铸铁管路连接件型式尺寸偏心异径外接头Malleable cast iron pipe fittings--Type size--Eccentric reducing male joints (sockets) 335 GB/T 3289.26-1982 可锻铸铁管路连接件型式尺寸内接头Malleable cast iron pipe fittings--Type size--Inner joints (nipples hexagon) 336 GB/T 3289.27-1982 可锻铸铁管路连接件型式尺寸异径内接头Malleable cast iron pipe fittings--Type size--Reducing inner joints(nipples hexagon) 337 GB/T 3289.28-1982 可锻铸铁管路连接件型式尺寸内外螺丝Malleable cast iron pipe fittings--Type size--Male and female screws (bushings) 338 GB/T 3289.29-1982 可锻铸铁管路连接件型式尺寸通丝外接头Malleable cast iron pipe fittings--Type size--Through thread male joint (sockets) 339 GB/T 3289.30-1982 可锻铸铁管路连接件型式尺寸锁紧螺母Malleable cast iron pipe fittings--Type size--Backnuts 340 GB/T 3289.31-1982 可锻铸铁管路连接件型式尺寸外方管堵Malleable cast iron pipe fittings--Type size--Outer-square plugs 341 GB/T 3289.32-1982 可锻铸铁管路连接件型式尺寸带边外方管堵Malleable cast iron pipe fittings--Type size--Outer-square beaded plugs 342 GB/T 3289.33-1982 可锻铸铁管路连接件型式尺寸内方管堵Malleable cast iron pipe fittings--Type size--Inner-square plugs 343GB/T 3289.34-1982 可锻铸铁管路连接件型式尺寸管帽Malleable cast iron pipe fittings--Type size--Tube caps (caps plugs) 344 GB/T 3289.35 -1982 可锻铸铁管路连接件型式尺寸活接弯头内外丝活接弯头Malleable cast iron pipe fittings-- Type size--Union elbows, male and female union elbows 345 GB/T 3289.36-1982 可锻铸铁管路连接件型式尺寸活接三通Malleable cast iron pipe fittings--Type size--Union tees 346 GB/T 3289.37-1982 可锻铸铁管路连接件型式尺寸平形活接头Malleable cast iron pipe fittings--Type size--Parallel unions 347 GB/T 3289.38-1982 可锻铸铁管路连接件型式尺寸锥形活接头Malleable cast iron pipe fittings--Type size--Taper unions 348 GB/T 3289.39-1982 可锻铸铁管路连接件型式尺寸平形活接头垫圈Malleable cast iron pipe fittings--Type size--Parallel union gaskets 349 GB/T 3374-1992 齿轮基本术语Basic terminology of gears 350 GB/T 3478.1-1995 圆柱直齿渐开线花键模数基本齿廓公差Straight cylindrical involute splines--Modules, basic rack profiles and tolerances 351 GB/T 3478.2-1995 圆柱直齿渐开线花键30°压力角尺寸表Straight cylindrical involute splines--30°pressure angle dimenslons tables 352 GB/T 3478.3-1995 圆柱直齿渐开线花键37.5°压力角尺寸表Straight cylindrical involute splines--37.5°pressure angle dimensions tables 353 GB/T 3478.4-1995 圆柱直齿渐开线花键45°压力角尺寸表Straight cylindrical involute splines--45°pressure angle dimensions tables 354 GB/T 3478.5-1995 圆柱直齿渐开线花键检验方法Straight cylindrical involute splines--Inspection methods 355 GB/T 3478.6-1995 圆柱直齿渐开线花键30°压力角M值和W值Straightcylindrical involute splines--30°pressurengle M and W values 356 GB/T 3478.7-1995 圆柱直齿渐开线花键37.5°压力角M值和W值Straight cylindrical involute splines--37.5°pressure angle M and W values 357 GB/T 3478.8-1995 圆柱直齿渐开线花键45°压力角M值和W值Straight cylindrical involute splines--45°pressure angle-M and W values 358 GB/T 3478.9-1995 圆柱直齿渐开线花键量棒Straight cylindrical involute splines--Measuring pin 359 GB/T 3507-1983 机械式联轴器公称扭矩系列Nominal torque series of the mechanical coupling 360 GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures360 GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures 361 GB/T 3633-1995 钢结构用扭剪型高强度螺栓连接副技术条件Technical requirement for sets of torshear type high strength bolt hexagon nut and plain washer for steel structures 362 GB/T 3733.1-1983 卡套式端直通管接头Straight thread connector--Assembly 363 GB/T 3733.2-1983 卡套式端直通接头体Straight thread connector--Body 364 GB/T 3734.1-1983 卡套式锥螺纹直通管接头Male connector--Assembly 365 GB/T 3734.2-1983 卡套式锥螺纹直通接头体Male connector--Body 366 GB/T 3735.1-1983 卡套式端直通长管接头Straight thread long connector--Assembly 367 GB/T 3735.2-1983 卡套式端直通长接头体Straight thread long connector--Body 368 GB/T 3736.1-1983 卡套式锥螺纹长管接头Male long connector--Assembly 369 GB/T 3736.2-1983 卡套式锥螺纹长接。

螺丝（Bolt / Screw）一、外六角螺栓/螺丝（Hex Head Cap Bolt / Screw---HCS）二、内六角螺丝（Socket Head Cap Screw---SHCS）1. 圆柱头内六角螺丝（Socket Head Cap Screw---SHCS）2. 半圆头内六角螺丝（Button Head Socket Cap Screw---BH SHCS）3. 平头/沉头内六角螺丝（Flat Head Socket Cap Screw---FH SHCS）4. 低头内六角螺丝（Low Head Socket Cap Screw---LH SHCS）三、内六角紧定螺钉（Socket Set Screw---SSS）1. 内六角平端紧定螺钉（Socket Set Screw with Die / Flat Point---SSS FT）2. 内六角球面紧定螺钉（Socket Set Screw with Round Point---SSS RD）3. 内六角锥端紧定螺钉（Socket Set Screw with Cone Point---SSS CN）4. 内六角凹端紧定螺钉（Socket Set Screw with Cup Point---SSS CP）5. 内六角滚花凹端紧定螺钉（Socket Set Screw with Knurled Cup Point---SSS KNL)6. 内六角长圆柱端紧定螺钉（Socket Set Screw with Full Dog Point---SSS DOG）7. 内六角短圆柱端紧定螺钉（Socket Set Screw with Half Dog Point---SSS ½DOG）四、内六角圆柱头轴肩螺钉（Socket Shoulder Screw）五、方头螺栓（Square Head Bolts---SQHD）六、马车螺栓（Carriage Bolt---CB）七、吊环螺栓（Eye Bolt）八、U型螺栓（U Bolt）九、牙条（Stud---14”以下/ Threaded Rod）十、机螺丝（Machine Screw---MS）常见头型：1. 圆头机螺丝（Round Head Machine Screw---RH MS）2. 平头/沉头机螺丝（Flat Head Machine Screw---FH MS）3. 盘头机螺丝（Pan Head Machine Screw---PH MS）4. 大扁头机螺丝（Truss Head Machine Screw---TH MS）5. 半沉头机螺丝（Oval Head Machine Screw）6. 圆柱头机螺丝（Cheese Head Machine Screw）7. 六角头带垫片螺丝（Hex Washer Head Screw）常见槽型：1. 一字槽（Slotted）2. 十字槽（Philips）3. 米字槽（Posidriv）4. 梅花槽（Torx）十一、自攻钉（Tapping Screw）常见头型：1. 盘头（Pan Head）2. 沉头（Flat Head）3. 半沉头（Oval Head）常见牙型：1. A型（Type A）2. B型（Type B）3. AB型（Type AB）4. 三角形（Trilobe / Thread Rolling）5. 17型（Type 17）6. F型（Type F）7. 23型（Type 23）8. 25型（Type 25）本文版权所属标准件之都网，如需转载、摘编或以其它方式使用本文内容，请在授权范围内使用，并标注“来源：标准件之都”。

外文名稱英文名稱六角螺絲(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角機械螺絲 HEX HEAD MACHINE BOLTS六角木牙螺絲 HEX LAG BOLTS四角螺絲 SQUARE HEAD BOLTST頭螺絲 T HEAD BOLTS馬車螺絲 CARRIAGE BOLTS環首螺絲 EYE BOLTS內六角孔螺絲 HEX SOCKET CAP SCREWS固定螺絲 SET SCREWS螺椿栓 STUD BOLTS螺旋椿 SCREW STUDS輪殼螺栓 WHEEL BOLTS翼形螺絲 WING SCREWS自攻螺絲 SELF TAPPING SCREWS自削螺絲 THREAD CUTTING SCREWS鑽尾螺絲 SELF DRILLING SCREWS旋入螺絲 DRIVE SCREWS機械螺絲 MACHINE SCREWS木螺絲 WOOD SCREWS家具螺絲 FURNITURE SCREWS塑板螺絲 CHIPBOARD SCREWS牆用螺絲 DRYWALL SCREWS基礎螺栓 FOUNDATION BOLTSU型螺栓 U BOLTS勾頭螺栓 HOOK BOLTS套掛螺絲 TOGGLE BOLTS突緣螺絲 FLANGE BOLTS軌道螺栓(魚尾螺絲) TRACK BOLTS耐候鋼螺絲 CORTEN STEEL HEAVY HEX BOLTS扭矩节造螺栓 T.C.BOLTS高張力螺栓 HIGH STRENGTH BOLTS剪力釘(焊接螺絲) WELDING STUDS螺絲附華司組合 SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓 BIG SIZE BOLTS不鏽鋼小螺絲 STAINLESS STEEL SHEET METAL SCREWS不鏽鋼大螺絲 STAINLESS STEEL BOLTS銅螺絲 BRASS SCREWS鋁螺絲 ALUMINUM SCREWS合金鋼螺絲 ALLOY STEEL SCREWS電女螺絲 ELECTRONIC SCREWS藐小精密螺絲 MICRO SCREWS塑膠螺絲 PLASTIC SCREWS復合材料用螺絲 PARTICLE BOARD SCREWS鈦合金螺絲 TITANIUM ALLOY BOLTS鈦、鋯、鉬、鈮等螺絲、零件、材料 TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺絲 THUMB SCREWS雙頭牙螺絲 DOUBLE END SCREWS HANGER BOLT車輛(汽車)螺絲、螺帽 AUTOMOTIVE FASTENERS航太用螺絲 AEROSPACE FASTENERS飛機特殊扣件 SOURCE CONTROL BOLTS拉栓 BLIND BOLTS面板螺絲 PANEL FASTENERS電梯螺絲 ELEVATOR BOLTS四角頭固定螺絲 SQUARE SET SCREWS大頭馬車螺絲 STEP BOLTS單向螺絲 ONE WAY LAG SCREWS管夾螺絲 HOSE CLAMP SCREWS不鏽鋼固定螺絲 STAINLESS STEEL HEX SOCKET CAP SCREWS不鏽鋼內六角螺絲 STAINLESS STEEL HEX SOCKET CAP SCREWS鉸鏈螺絲 HINGE SCREWS貨櫃螺絲 CONTAINER SCREWS復合材料鑽尾螺絲 BI-METAL SELF DRILLING SCREWS三角牙螺絲 TRILOBULAR THREAD SCREWS凹凸牙螺絲 HIGH LOW SCREWS夾板用螺絲 PARTICLE BOARD SCREWS馬桶螺絲 TOILET CLOSET BOLTS特長螺絲 SPECIAL LONGER SCREWS建業螺絲 BUILDING FASTENERS不鏽鋼六角螺絲 STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺絲 SPECIAL SCREWS OR BOLTS不鏽鋼特殊螺絲 SPECIAL STAINLESS STEEL SCREWS寬牙螺絲（粗牙螺絲） COARSE THREAD SCREWS鏈帶螺絲 COLLATED SCREWS水泥螺絲 CONCRETE SCREWS板模螺絲 CONSTRUCTION BOLTS鋅蝶螺絲 DIE CAST WING SCREWS; ZINC ALLOY重型車螺絲 HEAVY DUTY WHEEL HUB BOLTS內六角固定螺絲 HEX SOCKET SET SCREWS復合材料用螺絲（夾板用） PARTICLE BOARD SCREWS犁壁螺絲 PLOW BOLTS機(踏)車用螺絲、軸心 SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE針車用螺絲、軸心 SCREWS AND SHAFTS FOR SEWING MACHING行付螺絲 SOCKET SET SCREWS不鏽鋼寬牙螺絲 STAINLESS STEEL COARSE THREAD SCREWS不鏽鋼凹凸牙螺絲 STAINLESS STEEL HIGH-LOW THREAD SCREWS不鏽鋼機械螺絲 STAINLESS STEEL MACHINE SCREWS不鏽鋼鑽尾螺絲 STAINLESS STEEL SELF DRILLING SCREWS不鏽鋼自攻螺絲 STAINLESS STEEL SELF TAPPING SCREWS不銹鋼自削螺絲 STAINLESS STEEL THREAD CUTTING SCREWS不鏽鋼三角牙螺絲 STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不鏽鋼木螺絲 STAINLESS STEEL WOOD SCREWS套掛螺栓及螺絲 TOGGLE BOLTS鈦合金膨脹螺絲 TITANIUM ALLOY EXPANSION BOLTS本材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热措放：铸造编造的选用本则是什，，heat-treatment概况措放，温州烘箱厂家供当含浸缸：finish去氢：Lustrating hydrogen查验：Inspection包拆：Packing入库：Stocking车床：lathe磨造：grinding红打：hot forging冲压：punchingDiameter 曲径Length 长度1 标准GB （国标）ISO(国际标准)DIN （德造）JIS （日标）ANSI /ASME （美标）BA （英造）螺丝头型Pan 方头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米造槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓 C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cup head square neck bolts 半方头方螺栓Cup head nib bolts 半方头带榫螺栓Cup head square neck bolts with large head –product grade C大半方头方颈螺栓 C级外文名稱英文名稱六角蓋頭螺帽 HEX CAP NUTS六角鋸齒螺帽 HEX SERRATED NUTS六角輪緣螺帽 HEX FLANGE NUTS高腳螺帽 HEX COUPLING NUTS(HIGH NUTS)圓螺帽 ROUND NUTS四角螺帽 SQUARE NUTS管用螺帽 PIPE NUTS輪殼螺帽 WHEEL NUTS蝶型螺帽 WING NUTSU形螺帽 U NUTST形螺帽 T NUTS環首螺帽 EYE NUTS齒形螺帽 KEP NUTS齒花螺帽 CLINCH NUTS耐候鋼六角重型螺帽 CORTEN STEEL HEAVY HEX NUTS焊接螺帽 WELD NUTS高張力螺帽 HEIGH STRENGTH NUTS建業用螺帽 STRUCTURAL NUTS不鏽鋼螺帽 STAINLESS STEEL NUTS銅螺帽 BRASS NUTS鋁螺帽 ALUMINUM NUTS合金鋼螺帽 ALLOY STEEL NUTS重型車螺帽 HEAVY DUTY WHEEL HUB NUTS鐵器焊接袋帽 ACORN CAP NUTS金屬預放扭矩式螺帽 ALL-METAL PREVAILING TORQUE TYPE NUTS壁虎螺帽 ANCHOR NUTS大尺寸螺帽 BIG SIZE NUTS鐵蓋袋帽 CLOSED END ACORN NUTS盤形華司螺帽 CONICAL WASHER NUTS鐵蓋+尼龍圈組合蓋帽 DIN 986 DOMED CAP NUTS突緣尼龍蓋帽 FLANGE NYLON INSERT LOCK NUTS平面華司螺帽 FLAT WASER NUTS六角割溝螺帽 HEX SLOTTED NUT自鎖螺帽 SELF-LOCKING NUTS造行螺帽 SLIDING NUTSSLN-自動防鬆螺帽 SLN SELF-LOCKING NUTS其它特殊螺帽 SPECIAL NUTS彈簧螺帽 SPRING NUTS不鏽鋼突緣螺帽 STAINLESS STEEL FLANGE NUTS不鏽鋼六角輪緣尼龍螺帽 STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS不鏽鋼六角重型螺帽 STAINLESS STEEL HEAVY HEX NUTS不鏽鋼六角螺帽 STAINLESS STEEL HEX NUTS不鏽鋼尼龍嵌入螺帽 STAINLESS STEEL NYLON INSERT LOCK NUTS鋅壓屬螺帽 ZINC DIE CASTING NUTS通俗六角螺帽 HEX NUTS六角重型螺帽 HEAVY HEX NUTS薄型螺帽 HEX JAM NUTS尼龍嵌入防鬆螺帽 NYLON INSERT LOCK NUTS機械螺絲用六角螺帽 HEX MACHINE SCREW NUTBO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母Hexagon head bolts-product grade C六角头螺栓 C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹 C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆菌B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员 B 级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉2 螺纹M. MF (公造牙)UNC.UNF (美造牙)BSW.BSF (英造牙)3 海关编码螺栓螺帽垫圈外文名稱英文名稱合金鋼線材盤元 ALLOY STEEL WIRE ROD球狀化線材 ANNEALING WIRE AND ROD黑鐵絲 BL螺纹大径：Major Diam螺纹外径，重力铸造机价格：Pitch diam螺纹底径：Minor diam通行规：Go/No go gage机械机能：mechanical and physical propertiesunified thread 同一英造螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防行氢脆Case carburization 概况渗碳With across flats 对边With across corners 对角Radius of fillet:头下方角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏软度Vickers 维氏软度Brinell 布氏软度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械机能8级采用美国进口的贝尔德实空渎光谱阐发仪和德国斯派克公司进口的光谱阐发仪电进行阐发尝试，该仪器由二十个光谱通道，可反在几秒钟内阐发出各类铸锭成份。

螺旋线 helix螺纹 screw thread圆柱螺纹 parallel screw thread圆锥螺纹 taper screw thread外螺纹 external thread内螺纹 internal thread单线螺纹 single-start thread多线螺纹 multi-start thread右旋螺纹 right-hand thread左旋螺纹 left-hand thread自攻螺纹 tapping screw thread基本牙型 basic profile牙型角 thread angle牙型半角 half of thread angle公称直径 nominal diameter螺纹大径 major diameter螺纹小径 minor diameter螺纹中径 pitch diameter螺距 pitch螺纹导程 lead螺纹升角 lead angle螺纹牙厚 thread ridge thickness螺纹槽宽 thread groove width螺纹旋合长度 length of thread engagement螺纹接触高度 thread contact height螺距偏差 deviation in pitch螺距累积误差 cumulative error in pitch螺栓 bolt双头螺柱 stud六角头螺栓 hexagon bolt地脚螺栓 foundation boltT形螺栓 T-head bolt , hammer head bolt螺钉 screw紧定螺钉 set screw自攻螺钉 tapping screw吊环螺钉 lifting eye bolt开槽圆柱头螺钉 slotted cheese head screw开槽盘头螺钉 slotted pan head screw开槽沉头螺钉 slotted countersunk (flat) head screw开槽半沉头螺钉 slotted raised countersunk (oval) head screw开槽圆头螺钉 slotted round head screw内六角圆柱头螺钉 hexagon socket head cap head screw内六角沉头螺钉 hexagon socket countersunk head cap head screw 十字槽盘头螺钉 cross recessed pan head screw十字槽沉头螺钉 cross recessed countersunk head screw螺母 nut六角螺母 hexagon nut方螺母 square nut圆螺母 round nut滚花高螺母 knurled nut with collar翼形螺母 wing nut吊环螺母 lifting nut螺纹牙型thread tooth profile三角形螺纹triangular thread矩形螺纹square thread梯形螺纹trapezoidal (acme) thread锯齿形螺纹buttress thread外(阳)螺纹 ext ernal (male) thread内(阴)螺纹 int ernal (female) thread倒角chamfer球头round heads平头flat heads螺尾thread runout退刀(越程)槽undercut车外螺纹external thread lathing车内螺纹internal thread lathing套外螺纹covering external threadtapping钻孔drilling铰孔reaming通孔through hole盲孔blind hole螺纹盲孔blind threaded hole麻花钻twist drill钻头角point angle螺纹终止线thread end line公称直径nominal diameter螺纹大径major diameter螺纹小径 mi nor diameter螺纹中径pitch (effective) diameter牙底root牙顶crest螺距pitch导程lead旋向revolving direction螺纹角thread angle右旋螺纹right hand-thread左旋螺纹left hand-threadclockwise逆时针方向anti-clockwise线数number of starts单线螺纹single-start thread双线螺纹double-start thread多线螺纹multiple thread标准螺纹standard screw非标准螺纹nonstandard screw特殊螺纹special thread粗牙普通螺纹coarse pitch thread细牙普通螺纹fine pitch thread螺纹规格screw size普通(公制)螺纹general (metric) thread管螺纹pipe thread圆柱内管螺纹parallel internal pipe thread圆锥内管螺纹taper internal pipe thread圆柱外管螺纹parallel external pipe thread圆锥外管螺纹taper external pipe thread小螺纹mini thread传动螺纹transmission thread558非密封管螺纹 558 non-sealing pipe thread 558密封管螺纹558 sealing pipe thread608 sealing pipe thread米制锥螺纹metric taper thread自攻螺钉螺纹self-drilling screw thread木螺钉螺纹wooden nail thread气瓶专用螺纹thread for gas tanke螺纹紧固件screw fasteners螺纹旋合长度 length of thread engagement中旋合长度 thread engagement group-normal 螺栓bolt六角头螺栓hexagon head bolt双头螺柱stud有效长度effective length旋入(机件)端metal end露出端(旋螺母端) nut end螺栓联接bolt joint螺柱联接stud joint螺钉联接screw joint螺钉screw紧定螺钉set screw开槽球头螺钉slotted round head screw开槽圆柱头螺钉slotted cheese head screw开槽盘头螺钉slotted pan head screwslotted countersunk screw十字槽沉头螺钉philips countersunk screw内圆柱头六角螺钉 socket cap screw开槽锥端紧定螺钉 slotted cone pointed set screw开槽平端紧定螺slotted flat point set screw开槽长圆柱端紧定螺钉s lotted dog point set screw螺母nut六角螺母hex nut六角薄螺母hexagon thin nut内六角圆螺母castle nut六角开槽螺母hex slotted nutI型六角螺母A级和B级 grade A and grade B of type one hexagon nut 垫圈（片）washer or spacer平垫圈bright washer平垫圈倒角型chamfer bright washer小垫圈small washer大垫圈big washer特大垫圈very big washer-grade弹簧垫圈spring (lock)washer标准型弹簧垫圈standard spring washer轻型弹簧垫圈light type spring washer重型弹簧垫圈heavy type spring washer外舌止动垫圈tab washer轮gear轮毂hub轮辐spoke标准齿轮standard gear渐开线齿轮involute gear直齿圆柱齿轮 spur gear 斜齿轮helical gear锥(伞)齿轮bevel gear人字齿轮herringbone wheel蜗轮worm wheel蜗杆worm相交轴intersecting shaft主动(小齿)轮pinion从动(大齿)轮follower gear齿顶圆addendum circle齿根圆dedendum circle节圆（分度圆）直径 pitch circle diameter节点pitch point齿顶高addendum齿根高dedendum齿高total depth齿厚tooth thickness宽width of space齿距circular pitch齿宽tooth width齿数number of teeth模数module压力角pressure angle销pin圆柱销parallel (dowel) pin圆锥销taper pin开口(尾)销split cotter pin销联接pin joint键key普通平键parallel key圆头普通平键round end parallel key方头普通平键square parallel key单圆头普通平键single round parallel key 半圆键woodruff key钩头楔键gib head（taper）key花键spline键槽key way (slot)键联结key joint弹簧spring簧丝直(线)径wire diameter of spring弹簧外径external diameter弹簧内径internal diameter弹簧中径effective diameter弹簧节距pitch支承圈数number of end coils有效圈数number of active coils总圈数number of total coils自由高度free height弹簧丝展开长度stretched length of wire螺旋压缩弹簧 helical compression spring螺旋拉伸弹簧 helical extension spring螺旋扭转弹簧 helical torsion spring涡卷弹簧turbination spring板簧leaf spring片簧blade spring轴承bearing滚动轴承rolling bearing内圈inner race外圈outer race滚动体rolling element保持架、隔离圈 cage 深沟球轴承deep groove ball bearing推力球轴承thrust ball bearing 圆锥滚子轴承taper roller bearing 上轴瓦top shell下轴瓦bottom shell。

•acme screw thread爱克米螺纹•acme screw-thread阿克米制螺纹•adapter set screw接头调节螺钉•adjustable round split die with adjusting screw带调整螺钉的可调式圆板牙•adjustable screw type steering gear可调整式螺旋型转向装置•adjustable stop screw可调整止动螺钉•adjusting screw调整螺钉;调整螺丝;调准螺旋;调节螺钉;校正螺钉;校正螺旋•adjusting screw for elevation标高调整螺丝•adjusting screw for pan position锅体水平调节螺杆•adjusting screw for transverse横向调整螺丝•aerial screw飞机螺旋桨•aiming adjust screw瞄准调节螺钉•aiming screw瞄准调节螺钉•air intake adjusting screw进气调节螺钉•air screw空气螺旋桨•air-tight screw pump密闭式螺杆泵•Allen screw阿伦螺钉•allen screw六角固定螺丝•ampere's right handed screw rule安培右手螺旋定则•Ampere's right-hander screw rule安培右手定则•anchor screw基础螺栓•anchoring screw止动螺钉•annular screw plate环状板牙•antagonizing screw调置螺旋•antifriction ring holder screw减摩环托螺钉•arachnoid screw蛛网膜螺钉•arachnoid screw driver蛛网膜螺钉旋凿•Archimedean screw阿基米德螺线•Archimedean screw pump阿基米德螺旋泵•Archimedes'screw阿基米德螺旋•assembly screw安装螺旋•attachment screw连接螺钉;定位螺丝;止动螺钉•automatic screw lathe自动螺纹车床•automatic screw machine自动螺丝车床•auxiliary screw arc辅助螺钉弧形板•axis of screw螺旋轴线•azimuth adjusting screw方位调整螺钉•backing-up screw止动螺钉•backlash adjusting screw齿隙调整螺钉•ball screw滚珠丝杠•ball-bearing cap screw滚珠轴承盖螺钉•ball-jointed screw万向球铰螺杆•band wheel crank screw带轮曲柄螺丝•band wheel crank screw nut带轮曲柄螺丝帽•band wheel set screw带轮主头螺丝•banking screw止动螺钉•base screw底座螺钉•bearing for screw conveyer螺旋输送机轴承•bell screw钟形螺钉;丝锥接套•binding(post)screw接线螺钉•binding head screw扁头结合螺钉•blast cap screw鼓风盖螺钉•bleed screw带孔螺钉•body of screw螺钉体•body screw犁体螺钉•boiler lagging plate set screw锅炉套板止动螺钉•bolster screw jack车架螺旋千斤顶•bone screw接骨螺钉•bone screw and bolt outfit骨螺钉螺栓器械包•bone screw driver接骨螺钉旋凿•bone screw holding forceps接骨螺钉夹持钳•bone screw tap接骨螺钉丝攻•bottle screw螺旋起重机;螺旋起重器•bottom plate screw底板螺钉•brace screw撑柱螺丝•brace screw driver撑臂起子•brake screw制动螺杆•brake thrust screw制动器止推调节螺钉•brass countersunk head wood screw黄铜平头木螺丝•brass round head wood screw黄铜圆头木螺丝•brass screw down bib cock黄铜水龙头•brass screw down bib cock heavy type黄铜重型水龙头•brass shouldered cup screw hook黄铜螺丝弯钩•brass square screw hook黄铜螺丝曲尺钩•brass wood screw黄铜木螺丝•brass-plated mild steel round bead wood screw镀黄铜圆头软钢木螺丝•brass-plated mild steel round head machine screw镀黄铜圆头软钢机器螺丝•brazier head screw扁头螺钉•breaker arm adjusting screw断电臂调整螺钉•bright mild steel countersunk head wood screw光亮软钢平头木螺丝•bright mild steel round head wood screw光亮软钢圆头木螺丝•bronze screw hook古铜螺丝钩•bush set screw衬套制动螺钉•butterfly screw元宝螺钉•button-head cap screw圆头帽螺钉;半圆头紧固螺钉•button-head screw圆头螺钉•button-headed screw半圆头螺钉•buttress thread screw斜梯形纹螺钉•calibration screw校准螺钉•cap of screw螺钉帽•cap screw有头螺钉•capstan(-headed)screw绞盘螺钉•captive screw外加螺丝•carpenter's screw clamp台钳•carriage lock screw拖板锁紧螺钉•casale closure with external screw外螺纹卡扎里密封•central screw中心螺钉•centrifugal screw pump离心螺旋泵•centring screw定中心螺钉•chain adjusting screw链调节螺钉•chamfer head screw沉头螺钉•check screw止动螺钉•cheese head screw高平头螺丝•circumferential register screw圆周定位螺丝•clamp screw制动螺旋•clamp screw sextant制动螺钉六分仪•clamping screw固定螺钉•clip screw调置螺旋•closing screw螺纹规;螺纹塞•clutch adjusting screw离合器调整螺钉•clutch pressure plate screw离合器压板螺钉•coach screw方头螺钉;板头尖端木螺钉•coarse screw tap粗丝锥•coarse thread screw粗螺纹螺钉;粗纹螺钉•coarse-pitch screw大螺距螺钉•collar head screw头带缘螺钉•collar-head screw环头螺钉•combination screw driver set with tester带测电笔的套装螺丝刀•complete equipment for making wood screw木螺丝成套设备•compound feed-screw复式刀架丝杠•compound feed-screw graduated collar复刀架丝杠刻度圈•compound screw复式螺钉;复式螺旋•cone screw锥形螺钉•conical twin-screw extruder锥形双螺杆挤塑机•connecting screw rod连接螺杆•connection screw连接螺钉•constant taper screw等螺距锥体螺杆•contact screw接触螺钉•conveyer screw螺旋输送器•conveyer screw drive shaft输送机螺旋主动轴•conveyer screw shaft输送机螺旋轴•conveyer screw shaft coupling输送机螺旋轴联轴节•conveyer screw thrust plate输送螺旋止推板•copper-plated iron screw ring镀紫铜铁吊环螺钉•cored screw空心螺旋•correction screw校正螺钉;校正螺旋•correctional screw改正螺旋•cotter with screw end螺旋端锁销•countersunk head machine screw埋头机螺钉•countersunk head screw埋头螺钉•countersunk oval head screw埋头圆顶螺钉•countersunk screw埋头螺钉;埋头螺丝•coupling screw连接螺钉•cover screw盖用螺钉•credit screw信用紧缩•crest of screw thread螺纹牙顶•cross feed screw横进刀螺杆•cross feed screw crank横向进刀螺杆曲柄•cross feed screw dial横进刀螺杆指示盘;横向进刀螺杆指示盘•cross feed screw handle横向进刀丝杠手柄•cross lead screw横向丝杆•cross lead screw nut横向丝杆螺母•cross recess head screw十字槽头螺钉•cross screw左右交叉螺纹•cross slide screw横动台螺杆;横滑板螺杆•cross surfacing screw横动台螺杆•cross traverse screw横动台螺杆•crown screw牙冠用螺钉•cruciform screw driver十字形螺丝起子•cruciform slot screw十字槽螺钉•cup head screw半圆头螺钉;圆头螺钉•cup head wood screw圆头木螺丝;半圆头木螺钉•current regulator contact screw电流调节器接触螺钉•cutter for screw plate螺丝板加工刀具;螺丝板牙加工工具•decreasing lead screw减螺距螺杆•depth gauge for bone screw接骨螺钉长度测量器•depth screw gear耕深调节螺杆•depth-adjusting screw耕深调节螺杆•dial of vertical adjustable screw垂直可调丝杠•dial screw度盘螺钉•diameter of screw螺纹标称直径;螺旋直径•differential drive gear thrust screw差速器环齿轮推力螺钉•differential gear for screw conveyer螺旋输送机的差动装置•differential screw差动螺旋;差动装置螺钉•differential screw gearing差动螺旋传动装置•differential screw jack差动螺旋起重器•differential screw-jack差动螺旋千斤顶•differential-screw jack差动千斤顶•diopter rotating screw视度转螺•distributor adjusting screw分配调整器螺钉•dog(set;locating)screw定位螺钉•dog screw轧头螺钉;偏心头螺钉•dormant screw埋头螺钉•double flight feed screw双头螺旋加料器•double screw pump双螺杆泵•double worm screw双扭螺钻;麻花钻•double-screw bolt螺柱•double-screw washer双螺旋洗矿机•double-thread screw双头螺纹•double-threaded screw双纹螺钉•dowel screw扶手螺丝;两头螺钉;两头螺丝钉•down-feed screw垂直丝杠•draw screw起拉螺钉;起模螺钉•drive screw螺纹钉•driving screw导螺杆;导螺旋;主螺杆•drivre screw传动螺杆•duct adjusting screw墨斗调节螺丝•earth screw土钻;挖穴钻•earthing screw接地螺钉•eccentric-screw breechblock偏心闭锁机•Edison screw爱迪生螺纹;圆螺纹•electric screw clay gun电动螺旋式泥炮•electric screw down gear电动压下装置•electric screw driver电动螺丝刀;电动螺旋钻•electro-magnet screw press电磁螺旋压力机•electro-mechanical screw time release机电螺旋式限时解锁器•elevating endless screw升降蜗杆•elevating screw升降丝杠;上升螺旋;螺旋起重器•elevator screw升降机螺旋•endless screw蜗杆•endless tangent screw sextant微调螺杆六分仪•engine idling speed adjusting screw发动机怠速调整螺丝•English screw英制螺纹•English screw pitch ga(u)ge英制螺距规•Ericsson screw埃里克森螺纹•expansion screw扩开螺钉;可调螺钉•extension screw螺旋延长部•external screw螺钉•external screw cutting tool外螺纹车刀•external screw ga(u)ge外螺纹检查规•external screw thread finish外螺纹瓶口•extra fine screw特细牙螺纹•extruder screw压出机螺杆•extruding screw挤压螺杆•eye screw羊眼螺丝;吊环螺栓;环首螺钉;环首螺栓•eyepiece screw目镜螺丝;目镜螺旋•eyepiece screw-micrometer螺杆式目镜测微计•faceplate screw面板螺丝•faller screw针板螺杆•falt fillister screw凹槽扁头螺杆•fastening screw紧固螺钉•feed screw进给螺杆;螺旋给料机;螺旋送料机•feed screw collar进给螺杆挡环•feed screw mechanism进料螺杆机构•feed screw nut丝杆螺母•female screw阴螺丝;阴螺旋;螺母;内螺旋•female screw thread内螺纹•femoral screw股骨螺钉•ferrous and non-ferrous screw and nut黑色及有色金属螺钉和螺母•fillet of screw螺纹圈•filling screw螺纹规•fillister head screw凹槽帽螺钉•fine adjustment screw微调螺丝•fine screw tap细牙螺丝攻•fine thread screw细纹螺钉•fine-motion screw微动螺旋•fine-pitch screw细牙螺钉•finite-conductivity screw instability有限电导率螺旋不稳定性•fitting screw紧配连接螺栓;装配螺钉•fix screw固定螺丝•fixation screw needle固定螺丝针•flat counter-sunk head screw平顶埋头螺钉•flat end set screw平端固定螺钉•flat head screw平头螺钉;平头螺丝•flat point set screw平端定位螺钉•flat screw平头螺钉•flexible screw conveyer挠性螺旋输送器•flush head screw shackle平头螺栓卸扣•flux screw磁通调整螺钉•fly-headed screw蝶形头螺钉•focusing screw调焦螺旋•foot screw地脚螺钉;地脚螺丝;脚螺旋•foot-screw底脚螺丝•for screw stays用于螺丝固定•force screw力旋量•forcing screw紧固螺钉;起重器;加压螺钉•forked screw driver叉形螺丝刀;叉形螺旋起子•four-screw driver四用螺钉起子•four-screw leveling head四螺钉安平头•four-wheel screw jack四轮修车起重器;四轮修车起重器•friction screw press摩擦螺旋压力机;摩擦压力机•front screw前螺杆•fuel pump adjusting screw燃油泵调节螺钉•full-automatic screw machine全自动螺丝机床•full-flighted screw全程螺杆•fully automatic turret screw machine全自动转塔式车床•galvanized iron corn head screw镀锌尖头螺丝•galvanized iron screw白铁螺丝•galvanized iron screw hook镀锌螺钩•galvanized mild steel countersunk head wood screw镀锌沉头木螺丝•galvanized mild steel drive screw镀锌螺丝钉•galvanized mild steel roofing screw镀锌瓦楞螺丝•galvanized mild steel round head machine screw镀锌圆头机器螺丝•galvanized mild steel round head wood screw镀锌圆头木螺丝•galvanized MS countersunk head machine screw镀锌平头机器螺丝•galvanized screw镀锌螺钉;镀锌螺丝•galvanized screw plug镀锌旋塞•galvanized stay adjustable screw镀锌拉线调整螺丝•galvanized steel self tapping screw镀锌自攻螺线•gas valve screw气阀螺钉•gathering screw收集螺旋•gear motor for screw conveyer螺旋输送器减速电动机•geared worm screw传动蜗杆螺旋•generator frame through screw发电机架长螺杆•gib screw调整楔用螺钉;夹紧调整螺钉•governing screw调节螺钉•governor adjusting screw调节器调整螺钉•governor adjusting screw cap调速器调整螺钉帽•governor arm screw调速器杆螺钉•governor link screw调节器联杆螺钉•grain screw谷粒螺旋•grid of screw dislocations螺形位错十字格•grooved bone screw有槽接骨螺钉•ground screw地脚螺钉•grub screw平头螺钉;平头螺丝;木螺钉;木螺丝•guide screw导螺;丝杆•hairspring screw游丝螺钉•hairspring stud screw游丝外桩螺钉•half-bright screw半光制螺钉•half-round head screw半圆头螺丝•half-round screw半圆头螺钉•hammer-drive screw锤入式螺钉•hand brake band anchor bar adjusting screw手闸带锚定杆调整螺钉•hand driven screw press手动平板机•hand jack screw手力千斤顶•hand power screw press手动螺旋压机•hand power screw punching press手动螺旋压孔机•hand screw手动螺杆;手力千斤顶•hand screw clamp手螺旋夹•hand screw holdfast手螺旋夹•hand screw press手动螺旋压力机;手转压力机•hand screw tap手用丝锥•hand wheel screw down手轮压下装置•hand-operated screw press手动螺旋压力机•hand-operated vertical screw press手摇立式螺旋压榨机•hand-screw手动起重器•hand-screw vulcanizing press手旋硫化机•handle set screw车辆制动螺钉•handrail screw扶手螺丝•head lamp adjusting screw前灯调节螺钉•headless screw无头螺钉•headless set screw无头止动螺丝•headless shoulder screw无头轴肩螺钉•helical screw pulp conveyer螺旋纸浆传送器•helically bladed screw conveyer螺旋叶片式输送器•hermetic screw pump密闭式螺杆泵•hex socket screw key六角凹头螺钉键•hexagon cap screw六角帽螺钉•hexagonal head screw六角头螺钉;六角头螺栓•hexagonal socket screw六角凹头螺钉•high power screw press高能螺旋压力机•high precision lead-screw cutting lathe高精度丝杠车床•high viscosity triple screw pump高粘度三螺杆泵•holding screw紧定螺钉;紧固螺丝•holes for screw螺栓孔•hollow screw空心螺钉•hollow-head set-screw空心头固定螺钉•hook screw钩头螺钉;带钩螺钉•horizontal clamping screw水平制动螺钉•horizontal light beam adjusting screw水平光调节螺钉•horizontal parallax screw水平视差螺旋•horizontal screw pump卧式螺旋泵•housing adjusting screw压下调整螺丝•housing screw压下螺丝•Hunter's screw差动可逆可螺旋桨•hydraulic cylinder bleeder screw液压缸放出管螺钉•hydraulic screw press液压螺旋压力机•hyperbolic screw pump双曲线式螺杆泵•image screw映像旋量•impedance screw节流螺钉•impeller locking screw叶轮端螺钉•inboard screw内侧螺旋桨•inch screw die英制螺纹板牙•inch screw tap英制螺纹丝锥•independent screw chuck分动螺旋卡盘•inside screw螺母•inside screw and non-rising stem暗杆内螺纹•inside screw and rising stem(ISRS)明杆内螺纹•inside screw rising stem内螺纹明杆•instrument headed screw半埋头螺钉•internal screw内螺旋•internal screw cutting tool内螺纹车刀•internal screw finish内螺纹瓶口•internal screw ga(u)ge内螺纹规•internal screw pump内螺旋泵•internal screw thread内螺纹•international screw die公制螺丝钢板•international screw pitch gauge国际螺距规;国际螺距规•international screw tap公制丝锥•international screw thread国际标准螺纹•interrupted screw带槽螺钉•iron handle screw driver铁柄螺丝刀•iron screw铁螺钉•iron screw with square head方头铁螺钉•iron square head screw方头铁螺钉•iron wood screw铁制木螺钉•jack screw螺旋起重机;千斤顶螺杆;千斤顶螺丝•jack(ing)screw螺旋千斤顶•jacket band screw套带螺钉•jacking screw顶起螺丝•key screw螺丝把;螺旋键•kingpin stop screw主销定位螺丝•knuckle stop screw关节止动螺钉•knurled screw滚花螺钉;滚花螺杆•lag screw板头尖端木螺钉;方头螺钉•lag wood screw木螺钉•lang raising screw地轮起落螺杆•large flat head slotted screw大平槽头螺钉•latch bracket screw弹键托螺钉•latch screw弹键螺钉;门栓大螺丝•lead of screw螺旋导程•lead screw导螺杆;唱片盘首纹;丝杆;丝杠;引入槽•lead screw for cross-slide横向进给螺杆•lead screw for saddle床鞍螺杆•lead screw for top slide刀架螺杆•lead screw monocomparator导杆螺旋单象坐标仪•lead screw tester丝杆检查仪•lead-in screw引入螺钉•lead-screw导螺杠•lead-screw drive导螺杆驱动•lead-screw gear丝杠交换齿轮•leading screw lathe丝杠车床•leading screw support导螺杆轴承•left screw左螺旋•left-hand screw左螺旋•left-hand screw drill pipe反扣钻杆•left-handed screw左旋螺杆•lentil-headed screw扁头螺钉•level(l)ing screw校平螺旋•levelling screw水准螺旋•lever latch cap screw手柄弹键盖螺钉•lift link screw提升杆调整螺杆•lift(ing)screw螺旋起重器•lifting screw起模螺钉;千斤顶螺杆;升降螺杆•limit screw止动螺钉•limit screw pitch ga(u)ge螺距极限规•linkage levelling screw悬挂装置;调平螺杆•lock screw锁定螺钉•locking screw锁紧螺钉•log screw方头木螺丝;木螺钉;木螺丝•long bent point screw长弯头画线针•long lead screw长丝杠•long screw长螺丝•longitudinal parallax screw纵向视差螺旋•low noise air screw compressor低噪声螺杆空气压缩机•lubricating screw润滑螺旋;黄油枪•machine screw with oval countersunk fillister head半沉头螺钉•main(driving)screw主螺杆•main pin brass cotter set screw主销铜衬扁销止动螺钉•main valve head cap screw主阀盖有头螺钉•male screw阳螺旋;柱螺纹•male screw cutting tool外螺纹车刀•male screw thread外螺纹;阳螺纹•manual control screw手调螺钉•manually-operated screw手动压力螺丝•marine screw propeller船用螺旋桨•marking screw标号螺丝•marsh screw amphibian沼地螺旋推进水陆两用车•mass screw平衡螺钉•master screw母丝杠;标准螺旋•Maurer type screw press毛雷尔型螺旋压榨机•maximum fuel limit screw最大燃油限制螺钉•meantime screw调时螺钉•measuring screw测微螺丝•medium Edison screw-cap中等爱迪生螺旋灯头•medium egg-plant screw indicating lamp bulb中螺口茄形指示灯泡•meter screw公制螺纹•metering screw计量螺旋•metric screw pitch gauge米制螺距规;国际螺距规•metric screw thread公制粗牙螺纹;公制螺纹•micrometer adjusting screw微调螺钉•micrometer screw千分丝杠;微调螺钉•micrometer screw caliper测微螺旋卡尺•micrometer screw ga(u)ge螺旋测微计;螺旋千分尺•micrometric regulating screw微调螺钉•micrometric screw测微螺杆;测微螺旋•mill headed screw滚花头螺钉•mill screw轧机压下螺丝•milled edge thumb screw铣边翼形螺钉•milled screw滚花头螺钉•minimum fuel limit screw最小燃油限止螺钉•minus screw一字槽头螺钉•mirror screw镜螺旋;镜螺旋;镜面螺钉;镜面螺钉•mixer-with conical screw锥形螺旋搅拌机•mixing screw螺旋混合机;混合螺杆;混合用螺旋•mixing screw conveyer混合螺旋输送器•monkey screw wrench活扳手•mounting screw安装螺钉•multi-start screw thread多头螺纹•multiple-start screw thread多头螺纹•multiple-thread screw多头螺杆•multiple-threaded screw多头螺杆;多纹螺旋•mushroom head screw菌头螺钉;菌头螺钉•Napier's differential screw steering gear纳皮尔差动螺旋操舵装置•neck(ed)screw颈口螺旋;颈口螺旋•needle bar connecting link hinge screw麦果螺丝•nickel-plated double line iron screw hood镀镍双线螺旋帽•nickel-plated double line iron screw hook镀镍双线螺旋钩•nickel-plated iron screw eye镀镍铁螺丝眼•nickel-plated iron screw hook镀镍铁螺旋钩•nickel-plated mild steel round head machine screw镀镍低碳钢圆头机器螺丝•nickel-plated mild steel round head wood screw镀镍低碳钢圆头木螺丝•nickel-plated steel self tapping screw镀镍钢制自攻螺丝•no screw balance无平衡螺钉摆轮•nozzle adjusting screw喷管调节螺钉•nut screw螺母•observation tube fixing screw抽筒固定螺旋•odd-pitch screw非标准螺纹•oil cup cover screw油杯盖螺钉•oil pressure adjusting screw油压调节螺钉•oil pressure switch screw油压开关螺丝•oil reservoir cover screw储油器盖止动螺钉•oil-hole screw油孔螺钉•oil-pressure adjusting screw油压的调节螺丝•one start screw单头螺纹•open screw gill drawing frame单针并条机•oscillating screw摆动螺钉•outer set screw外固定螺钉•outside screw and yoke type(OS&Y)轭式外螺纹•outside screw non-bonnet(OSNB)无压盖外螺纹•oval countersunk fillister head machine screw半沉头机器螺钉•oval countersunk fillister head wood screw半沉头木螺钉•oval countersunk screw椭圆埋头螺钉•oval fillister head screw球面圆柱头螺钉•oval head screw椭圆头螺丝•oval slotted countersunk head unloosing screw半沉头不脱出螺钉•packing screw衬垫螺旋•paddle screw conveyer叶片式螺旋输送器•panhead screw大柱头螺钉;锅头螺丝•pattern screw起模螺钉•percussion screw press直接电动螺旋锤;直接电动螺旋压力机•Persian screw螺旋排水机•Philips screw菲氏螺钉;带十字槽头的螺钉•Phillips screw菲利浦螺钉;十字槽螺钉•pilot screw支持螺丝•pinching screw夹紧螺钉;固定螺钉•pipe screw-cutting lathe管子螺纹车床•piston heat set screw活塞头止动螺钉•piston pin locking screw活塞销锁紧螺钉•piston pin set screw活塞销锁紧螺钉•piston stop screw活塞头止动螺钉•pivot screw枢轴螺钉•pivot-point screw枢轴螺旋•plain bone screw无槽接骨螺钉•plain screw平螺钉•plain-ended screw平端螺钉•plug machine screw tap机用中丝锥•plug screw螺塞•plug screw ga(u)ge阴螺纹规•plus screw十字槽头螺钉•plus-minus screw调整螺钉;调整螺丝;调整用螺钉•pneumatic screw press气动螺旋压机•pointless screw平端螺钉•porcelain head screw瓷头螺丝•porcelain screw holder瓷螺丝灯头•porcelain screw socket瓷螺丝灯座•positioning screw定位螺钉•positive-column screw instability螺旋不稳定性•positive-displacement screw type compressor正排量螺旋式压气机•pottery topped brass screw瓷头铜螺丝•power screw传动螺杆;传力螺钉•power transmission screw动力传动螺杆•power-driven screw-jack set电动螺旋起重机组•precision lead screw精密丝杠•pressure regulating thumb screw压脚调节翼形螺钉•pressure screw压力螺钉;压下螺丝•pressure screw check nut压力螺钉防松螺母•pressure screw extractor螺旋压榨机•pressure-adjusting screw压力调整螺钉•proportion set screw比例度设定螺丝•pull-out piece spring screw压簧螺钉•push-pull screw推拉螺杆•pusher screw推进式螺旋桨•quadruple screw四头螺旋;四纹螺旋;四线螺旋•quadruple screw motor ship四螺旋桨船•quick-motion screw速动螺旋•radial feed screw径向进给丝杠;径向进给丝杠•radiator screw-cap散热器加水盖•rag screw棘螺栓•raised head screw凸头螺钉•rapid screw大节距螺钉•ratchet screw jack棘轮螺旋起重器•reaming holes for screw stays为固定螺钉用的铰孔•rear furrow wheel adjustment screw尾轮调节螺钉•rear screw shaft后螺旋桨•rear screw shaft bushing后螺轴衬套•recalibration screw重新校准螺钉•recessed-head screw-driver槽头螺丝刀•rectilinear screw-thread reluctance motor直线螺纹磁阻电动机•reduction screw螺旋还原反应器•regular screw thread基本螺纹•regular screw threads普通螺纹•regular thumb screw对称翼形螺钉•regulating screw调整螺钉;调整螺丝•regulating stem set screw调节杆止动螺钉•regulator spring screw调节簧螺钉•restriction screw节流尖头螺钉;节流螺旋杆;带螺纹针阀•restrictor screw节制孔螺钉•retainer screw护圈螺钉•retaining screw固定螺钉•retention screw止动螺钉;定位螺钉;紧固螺钉•reverse screw回动丝杠•reverse-flighted screw双向螺杆•reversing screw回动螺旋•reversing screw bolt回动螺栓•reversing screw bottom guide回动螺杆下导板•reversing screw gudgeon回动螺旋•reversing screw top guide回动螺旋上导板•revolution speed of screw螺旋转速•ribbon type screw conveyer带状螺旋运输机•rigging screw装配螺钉;松紧螺旋扣;系紧螺钉•rigging-and-left-hand-screw clip左右向螺杆夹•right-and-left screw左右旋螺栓•right-hand screw右螺旋•right-hand screw rule右手螺旋定则•right-hand screw thread右螺纹;右旋螺纹•right-handed screw右旋螺钉;右旋螺旋杆•right-handed thread screw右螺纹螺杆•ring screw环头螺钉•ring screw ga(u)ge螺纹环规•rolled-thread screw滚丝螺钉•rolling mill screw down轧机的压下装置•rotary helical screw compressor回转式螺杆压缩机•rotary screw compressor旋转螺旋压缩机•rotation set screw转动限位螺钉•round head wood screw圆头木螺钉•round wood screw圆头木螺钉•roundhead screw圆头螺钉•roundheaded wood screw圆头木螺丝•saddle feed screw鞍架进给螺杆•saddle traverse screw鞍架进给螺杆•safety locking screw保险止动螺钉•safety set screw安全螺丝;安全止动螺钉•scoketed screw凹头螺钉•screw螺钉;螺丝;螺旋•screw action捻旋作用•screw adjusting double caliper螺钉调整内外卡尺•screw adjusting inside caliper螺钉调整内卡尺•screw adjusting outside caliper螺钉调整外卡尺•screw adjustment螺钉调整•screw and double nut螺丝和双螺母•screw arbor螺杆•screw auger推运螺旋•screw axes螺旋对称轴•screw axis螺旋轴•screw base螺钉座•screw base fuse螺旋式熔断器•screw bell钻杆打捞器•screw belt螺钉带•screw belt fastener螺钉带扣•screw blade螺旋刀片;螺旋桨叶;螺旋式叶片•screw blank螺钉坯件•screw bolt螺杆;螺栓;全螺纹螺栓•screw bolt and nut螺栓和螺母•screw brake螺杆闸•screw bushing螺旋轴衬•screw cap螺母;螺丝管帽;螺丝帽•screw capping拧盖•screw case螺杆箱•screw case box螺杆箱机座•screw case suppressing metal螺杆箱紧固件•screw chaser螺纹板牙;螺纹梳刀;修正孔用丝锥•screw chases螺丝版框•screw chasing螺纹切削•screw chasing machine螺丝车床;螺纹切削机;制螺旋机•screw chasing tool螺纹梳刀•screw clamp螺丝夹;螺旋夹•screw clamp for brake shoe lining装制动磨擦夹片•screw clamp for lubricating leaf spring钢板弹簧上油卡子•screw coal conveyer螺旋式输煤机•screw coal unloader螺旋卸煤机•screw collar螺旋环;环状螺母•screw comb螺纹梳刀•screw composing-stick螺丝排字手托•screw compressor螺旋压气机;螺旋压缩机•screw compressor clamp螺旋压缩机管夹•screw cone螺旋锥体•screw contact螺丝触点•screw control压下控制•screw conveyer螺旋输送机•screw correction螺旋形失真校正•screw cramp螺丝夹钳•screw cutter螺纹刀具•screw cutting螺纹切削;切螺纹;切削螺纹;车螺纹•screw cutting dies板牙•screw cutting lathe车螺丝车床;螺丝车床•screw cutting machine螺纹切削机;螺旋切削机•screw decanter螺旋沉降器;螺旋澄清器•screw depth control螺杆式深度调节器•screw depth regulator螺旋式入土深度调节器•screw diad二重螺旋轴•screw diameter螺旋直径•screw die螺丝板牙;平丝板•screw dislocation螺线位错;螺旋位错•screw displacement螺旋位移•screw drive螺杆传动•screw driver螺丝批•screw driver with wooden scales夹柄螺丝批•screw drum螺旋转鼓•screw elevator螺旋升运器;螺旋式升降机;螺旋提升机;螺旋牙根挺•screw extractor断螺钉取出器;起螺丝器•screw extruder螺旋挤压机;螺旋压出机•screw extrusion machine蜗杆挤压机•screw extrusion press螺旋挤出机;螺旋挤压机•screw eye螺丝眼•screw eye(羊眼)羊眼圈•screw fan螺旋扇风机;轴流式扇风机•screw fastener螺钉扣•screw fastening螺钉连接;螺丝接合•screw feed螺旋喂送器•screw feed grease cup滑脂杯•screw feed mechanism螺旋加料机构•screw feeder螺杆给料机;螺旋加料器•screw fixing螺丝固定•screw flange栓接法兰•screw flange coupling螺钉凸缘联轴节•screw for alarm clock闹钟螺钉•screw for bearing wheel of oscillating weight自动锤轴承螺钉•screw for framework of automatic device自动框架螺钉•screw for indicator guard日历指示器护板螺钉•screw for jumper spring跳杆簧螺钉•screw for motor starter马达起动器螺钉•screw for setting lever spring压簧螺钉•screw for starter fixing clamp起动器固定夹螺钉•screw friction press螺旋摩擦压力机•screw ga(u)ge螺纹规•screw ga(u)ge(S.G.)螺纹量规•screw gauge for taper thread锥形螺纹量规•screw gear螺纹传动装置;螺旋齿轮;压下装置•screw gearing螺旋齿轮传动装置;蜗轮蜗杆传动装置•screw gill drawing frame螺旋杆式并条机•screw gun螺旋式油枪•screw head file螺钉头锉•screw height control螺杆式高度调节器•screw holder螺口灯头;螺丝夹持器•screw holding forceps持螺丝钳•screw home拧紧•screw hoop环首螺栓•screw horseporew推进器马力•screw housing clearance推运螺旋与壳间间隙•screw hub seal蜗杆毂密封•screw impeller螺旋叶轮•screw impeller pump螺旋桨式泵•screw jaw with lug带舌螺扣接杆•screw jaw with movable lug带活舌螺扣接杆•screw joint螺管接头;螺旋接合•screw key螺丝扳手;螺旋键•screw lid螺旋盖•screw lift螺旋提升机•screw lifting mechanism螺旋提升机构•screw lower bridge of automatic device自动装置下夹板螺钉•screw lubrication螺旋润滑•screw machine自动车床;制螺钉机•screw making machine制螺钉机•screw mandrel螺旋心轴;丝杆•screw micrometer螺杆测微计•screw micrometer cal(l)iper螺旋千分卡尺•screw microscope螺旋测微镜•screw mixer螺旋轴搅拌机•screw motor螺杆马达•screw nail螺丝钉;螺纹钉;木螺钉•screw nicking machine螺钉头开槽机•screw nut螺母•screw of tangential cutter head切向进刀架丝杠•screw off拧松•screw on拧上•screw pair丝杠螺母副;螺旋副•screw pile螺旋桩•screw pile foundation螺旋桩基•screw pin螺旋销•screw pin countersink shackle埋头螺丝卸扣•screw pinch螺旋箍缩•screw pitch螺纹距;螺旋节距•screw plasticating injection molding螺杆塑化式注塑•screw plate螺丝板牙;螺丝钢板;螺丝模;搓丝板;搓丝机;板牙•screw plow螺旋形犁•screw plug螺旋接线柱;螺旋塞•screw plug ga(u)ge螺纹塞规•screw press螺旋压机;螺旋压力机•screw prop千斤顶•screw propellor for boat船用螺旋桨推进器•screw pump螺杆泵;螺旋泵•screw punch螺旋冲压机•screw rack斜齿条•screw rail bender螺杆弯轨机•screw release螺旋式限时解锁器•screw remover去螺钉器•screw retention螺纹防松装置•screw reverse gear螺旋回动装置•screw ring环首螺钉•screw ring ga(u)ge螺纹环规•screw rivet螺纹铆钉;螺旋铆钉•screw riveting machine螺旋铆机•screw rod螺杆•screw rolling machine滚丝机•screw rule螺旋定则•screw shackle螺纹联接环;螺纹连接环•screw shaft螺杆轴;螺旋轴•screw shaft bushing螺旋轴衬套•screw shank螺钉杆•screw shaped mo(u)ldboard螺旋形犁壁•screw shaving machine制螺母及螺栓头机•screw sheel螺旋套筒;灯头螺口•screw shell螺旋套管•screw snap ga(u)ge螺纹卡规•screw socket螺丝灯头;螺丝套筒•screw spike螺丝钉;螺纹道钉;螺旋道钉•screw spindle螺旋轴•screw spreader螺旋传送器;螺旋分布器•screw stairs盘旋式楼梯•screw stem螺杆•screw stock螺旋扳手•screw stopper螺旋塞•screw stud双头螺栓•screw support for adjusting regulator调整快慢针的螺钉座•screw swinging mechanism螺旋摆动机构•screw tap丝锥•screw templet螺纹样板•screw terminal螺丝接线端•screw testing interferometer螺杆检验干涉仪;检验螺纹干涉仪•screw tight fitting紧配螺旋•screw tightener压紧螺钉•screw tip蜗杆梢•screw tourniquet螺旋止血带•screw tow bar螺旋式牵引杆•screw triad三重螺旋轴•screw tube罗纹管•screw type oil expeller螺旋榨油机•screw unit组合机床的动力头•screw up拧紧•screw value螺旋周值•screw valve螺旋球阀•screw vent螺杆通孔•screw ventilation螺旋桨式风机;螺旋通风器•screw vice螺旋虎钳•screw washer螺旋垫圈;螺旋洗矿机•screw wedge丝杆调节楔•screw willow螺旋威罗机•screw winder螺杆式络纱机•screw wiper螺旋式擦拭器•screw wire螺钉用钢丝•screw with diamond knurls金刚石滚花头螺钉•screw with flat head平头螺钉•screw with knurled head滚花头螺钉•screw with round head圆头螺钉•screw with straight-line直线滚花头螺钉•screw with straight-line knurls直线滚花头螺钉•screw without nut无帽螺钉•screw worm螺旋锥蝇幼虫•screw wrench螺钉扳手;活动扳手•screw-and-nut mechanism螺杆螺母传动机构•screw-and-nut steering gear螺杆螺母式转向器•screw-and-nut steering-gear螺杆螺母转向装置•screw-cap螺旋帽•screw-cutting lathe车螺纹车床•screw-cutting machine螺纹切削机床•screw-down压下机构•screw-driven螺旋传动•screw-driven planer螺杆传动刨床;丝杠式刨床•screw-driven planing machine螺杆传动刨床•screw-driven shaper螺杆传动牛头刨;丝杠式牛头刨床•screw-driven slotter丝杠式插床•screw-driver bit螺丝刀。

英文名称对应标准Square head bolts GB/T 8-88 C 级Flat countersunk square neck bolts GB/T 10-88 沉头沉带榫螺栓Flate countersunk nib bolts GB/T 11-88 (大)半圆头方颈螺栓Cup head square neck (with large head)bolt GB/T 14/15-88六角头铰制孔用螺栓Hexagon fit boltsGB/T 27-88 A 和B 级六角头螺杆带铰制孔用螺栓(细杆)Hexagon fit bolts with split pin hole on shank(Reduced shank) GB/T 28-88 A 和B 级十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation GB/T 29.2-88 A 和B 级六角头头部带孔螺栓Hexagon bolts with wire holes on head GB/T 32.1-88 A 和B 级T 型槽用螺栓Bolt for T-slot GB/T 35.1-88 B 级加强半圆头方颈螺栓Strengthened cap head square neck bolts GB/T 794.1-93 活节螺栓Eye bolts GB/T798-88地角螺栓Eyelet bolts GB/T799-88头角头螺栓Hexagon head bolts GB/T5780-2000 C 级六角头法兰面螺栓Hexagon flange bolts GB/T5789-86 B 级外六角花法兰面螺栓Steel hexalobular head bolt with small flangeDIN 34801-9918.久美特Geomet 19.耐落Nylok 陆锈宝Rupst 20.翡丽雅特 ViridAct 21.美加力Magni 沉头方劲螺栓中文名称一.孔别三.常用名称1.螺丝类方头螺栓1.割沟Slotted2.十字穴 Phillips3.米字穴 Pozidriv(cross recess)4.十字割沟 Slotted phillips5.四角孔Square6.十字方孔 Square phillips7.六角孔hexagon8.方孔割沟Square slotted9.梅花穴Six-lobe 10.三角孔Triangle 11.Y 型槽Y-type 12.斜Y 槽Tri-wing 13.五等角5-Point 二,电镀1.电镀锌Zinc plated2.白皮Plain finished3.五彩Yellow zinc plated4.镀镍Nickel plated5.热浸锌Hot dip galvanized6.黑锌Black zinc plated7.镀黑Black finished8.染黑Black oxide9.(黑)磷酸盐(black)Phosphated 10.黄铜 Brass 11.镀青蓝Unichrome plated 12.古铜A.C Brontze 13.青古铜Antique brass 14.机械镀锌Mechanical galvanized 15.绿锌Green zinc plated 16.电锌腊Zinc plated&waxed 17.达克锈Dacrotizing plated英文名称对应标准双头螺柱bm=1d Double end studs-bm=1d GB/T 897-88等长双头螺柱 B 级Double end studs(clamping type)-product grade A GB/T 901-88螺杆Thread rods GB/T 15389-943.螺钉类英文名称对应标准开槽圆柱头螺钉Slotted cheese head screws GB/T65-2000开槽沉头螺钉Slotted countersunk flat head screws (common head style) GB/T68-2000 eqv ISO 2009-94开槽半沉头螺钉Countersunk slotted raised head screws(common head style)GB/T69-2000 eqv ISO 2010-94内六角圆柱头螺钉Hexagon socket head cap screws GB/T70.1-2000 eqv ISO 4762.2-97内六角平圆头螺钉Hexagon socket button head screws GB/T70.2-2000 eqv ISO 7380-97内六角沉头螺钉Hexagon socket countersunk head screws GB/T70.3-2000 eqv ISO 10642-97十字槽盘头螺钉Pan head screw with cross recess GB/T818-2000 eqv ISO 7045-94十字槽半沉头螺钉Countersunk raised head screws(common head style)with cross recess GB/T820-2000 eqv ISO 7047-94十字槽圆柱头螺钉Cheese head screws with cross recess GB/T822-2000 eqv ISO 7048-94滚花高头螺钉Knurled thumb screws GB 834-88滚花平头螺钉Knurled screws GB 835-88内六角花形盘头螺钉Hexagon lobular socket pan head scerws GB 2672-86内六角圆柱头轴肩螺钉Hexagon socket head shoulder scerws GB/T 5281-854.自攻螺钉 英文名称对应标准十字槽盘头盘自攻螺钉Cross recessed pan head tapping screws GB 845-85十字槽沉头盘自攻螺钉Cross recessed countersunk head tapping screws GB 846-85十字槽盘头盘自攻锁紧螺钉Cross recessed pan head thread forming screws GB 6560-86十字槽凹穴六角头自攻螺钉Cross recessed hexagon head tapping screws with indentationGB 9456-98十字槽自攻螺钉-刮削端(用于精密机械)cross recessed tapping screws-scrape point(fasters for fine mechanics)GB/T 13806-2墙板自攻螺钉Dry wall screws GB/T14210-93十字槽盘头自钻自攻螺钉Cross recessed pan head self-drilling tapping screws GB/T15856.1-95六角凸缘自攻螺钉Hexagon head tapping screws with collarGB/T16824.1-97 eqv ISO 7053-92中文名称中文名称中文名称英文名称对应标准方螺母-C 级Square nuts-product grade C GB/T39-88六角螺母-C 级Hexagon nuts-product grade C GB/T41-2000eqv ISO 4034-99六角厚螺母Hexagon thick nuts GB/T56-88六角薄螺母Hexagon thin nuts GB/T6172.1-2000eqvISO 4035-99蝶形螺母Wing nuts GB/T 62-88组合式盖形螺母Acorn nutsGB/T 802-88球面六角螺母Hexagon nut with raised face GB/T 804-88滚花高螺母kunrled nut with collarGB/T 806-881型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert).style 1GB/T889.1-2000eqv 7040-97盖形螺母Acorn nutsGB/T 923-88六角薄螺母 无倒角Hexagon thin nuts (unchamfered)GB/T6174-2000eqvISO 4036-99六 角法兰面螺母Hexagon nuts with flangeGB/T6177.1-2000eqv ISO 4161-991型六角开槽螺母Hexagon slotted and castle nuts.style1GB/T 6178-86全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts GB/T 6184-2000eqv ISO 7719-97焊接方螺母square weld nut GB/T 13680-92焊接六角螺母Hexagon weld nuts GB/T 13681-92平头铆螺母Flat head riveted nuts GB/T 17880.1-996.挡圈 英文名称对应标准锥销锁紧挡圈Lock ring with corne pin GB/T 883-86轴肩挡圈Rings for shouderGB/T 891-86螺钉紧固轴端挡圈Lock rings at the end of shaft with screw GB/T 893.1-86孔用弹性挡圈-A 型Circlips for holes -typeA GB/T 894.1-86轴用弹性挡圈Circlips for shaft -typeA GB/T 895-2-86开口挡圈"E"ringsGB/T 896-86钢丝锁圈Round coire circlips GB/T 921-86夹紧挡圈Crip ringsGB/T 960-86中文名称中文名称英文名称对应标准弹簧垫圈(标准型)Single coil spring lock washers (normal type)GB/T 93-87平垫圈-C 级Plain washersGB/T 95-85eqv ISO 7091-2000大平垫圈Plain washers-large series GB/T 96-85 A 和B 级鞍形弹性垫圈Curved spring washers GB/T 860-87内齿锁紧垫圈Lock washers internal teethGB/T 861.1-87内锯齿锁紧垫圈Serrated lock washers internal teeth GB/T 861.2-87外锯齿锁紧垫圈Serrated lock washers external teeth GB/T 862.2-87波型弹性垫圈Wave spring washersGB/T 955-87锥形锁紧垫圈Countersunk external toothed look washersGB/T 956.1-87锥形锯齿锁紧垫圈Countersunk serrated external toothed lock washers GB/T 956.2-878.销英文名称对应标准开口销Split pins GB/T 91-2000eqvISO1234-97圆锥销Taper pinsGB/T 117-2000eqvISO2339-86螺纹圆柱销Paraller pins with external thread GB/T 878-86销轴Clevis pins with head GB/T 882-86平头铆钉Flat head rivetsGB/T 109-86平锥头铆钉（粗制）Cone-head rivets-black GB/T 864-86空心铆钉Tubular rivetsGB/T 876-86封闭型扁圆头抽芯铆钉Mushroom head break mandred closed end blind rivets GB/T 12615-90开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivetsGB/T 12617-90中文名称中文名称9.紧固件-组合件和连接副英文名称对应标准中文名称钢结构用高强度大六角头螺栓High strength bolts with large hexagon head for steel structures GB/T1230-91钢结构用高强度大六角头螺母High strength large hexagon nuts for steel stuctures GB/T1229-91钢结构用高强度大六角头垫圈High strength plain washers for steel structures GB/T1230-91钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures GB/T3632-95十字槽盘头螺钉,弹簧垫圈和平垫圈组合件Cross recessed pan head screw ,single coil spring lock washer and plain washer assemblies GB/T 9074-.4-88无头焊钉Headless for stud welding GB/T 10432-89圆柱头焊钉Cheese head studs for stud welding GB/T 10433-89机械焊接螺钉Weld screws with metric thread DIN 34817-2001。

.当你进入国外的实验室之前，如果不能熟练掌握实验过程中相关物品的英文名称及读音，你与同处一室的技术人员之间必将产生强烈的交流障碍，实验效率也将因此大打折扣。

这里我汇总了数篇文章的相关内容，并结合自己实验室的情况，补充了大量词汇，希望对即将出国留学的生物学科研人员有所帮助。

欢迎大家补充指正。

一．容器与耗材（vessel & consumable material）小瓶，vial量杯，measuring cup烧杯，beaker量筒，measuring flask量筒，measuring cylinderer坩埚，crucible坩埚钳，crucible clamp试管，test tube漏斗，funnel比色皿，cuvette鱼缸，aquarium烧瓶，flask锥形瓶，conical flask塞子，stopper/plug洗瓶，plastic wash bottle玻璃活塞，stopcock试剂瓶，reagent bottles玻棒，glass rod搅拌棒，stirring rod容量瓶，volumetric flask/measuring flask. 移液管，(one-mark) pipette吸液管，pipette滤器，filter滤纸，filter paper培养皿，culture dish移液枪，pipette移液枪枪头，pipette tips剃刀刀片，razor blade手术刀，scalpel垃圾袋，disposable bag垃圾桶，garbage bin橡皮筋，rubber band托盘，Tray铝箔，aluminium foil洗耳球，rubber suction bulb保鲜膜，preservative film研磨钵，mortar研杵，pestle小滴管，dropper蒸馏装置，distilling apparatus桶，bucket广口瓶，wide-mouth bottle离心机转子，rotor试管架，test tube holder/rack酒精灯，alcohol burner酒精喷灯，blast alcohol burner搅拌装置，stirring device石蜡封口膜，Parafilm. 微量离心管（EP管），Eppendorf tube载玻片，Slide盖玻片，Cover glass离心管，Centrifuge tube电泳槽，Gel tank电线，Electrical leads牙签，Toothpick螺丝钉，Screw锁紧螺母，Nut, Cap nut复印纸，Copy paper复写纸，Carbon paper钉，Nail试管刷，test-tube brush计时器，Timer闹钟，Alarm clockU形钉，Staple衣服挂钩，Coat hanger电泳用的梳子，Comb扳手，Shifting spanner订书机，Stapler订书钉，staple圆珠笔芯，Refill灯泡，Globe记号笔，marker pen注射器，syringe注射器活塞，plunger铁架台，iron support万能夹，extension clamp. 止水夹，flatjaw pinchcock圆形漏斗架，cast-iron ring橡胶管，rubber tubing药匙，lab spoon镊子，forceps剪刀，scissor打孔器，stopper borerpH试纸，universal ph indicator paper称量纸，weighing paper擦镜纸，wiper for lens水银温度计，mercury-filled thermometer真空泵，vacuum pump水浴锅，water bath kettle口罩，respirator电极，electrode阳极/正极，anode阴极/负极，cathode丢弃，discard转移容器，decant吸出，aspirate吹吸，blowing and suction离心收集，pellet重悬，resuspend絮状沉淀，flocculent precipitate浑浊的，turbid烘，bake灭菌，sterilize培养，foster. 通风，ventilate冷却，chill down稀释，dilute洗脱，elute孵育，incubate裂解物，Lysate沉淀物，Sediment上清，Supernatant色谱，chromatograph沉淀，precipitate接种，inoculate蒸馏，distil/distill搅拌，Stir/agitate中和，neutralize漂洗，rinse脱水，dehydrate发酵，fermentation溶解，dissolve燃烧，combustion水解，hydrolysis过滤，filtrate催化剂，catalyst研磨，grind破碎，crush催化作用，catalysis分解，dissolution涡旋震荡，Vortex电泳，Electrophoresis. 抽滤，suction filtration电转化，electrotransformation收菌，harvest切碎，chop/mince灌注，perfusion浆液，slurry恒温循环仪，Thermostatic circulator空调机，Air conditionerpH计，pH meter磁力搅拌器，magnetic stirrer烘箱，oven微波炉，microwave oven电磁炉，electromagnetic oven凝胶系统，Gel system电子天平，Electronic balance转接器，Adapter离心机，centrifuge封口设备，Sealing equipment复印机，Duplicator, copying machine超净工作台，super clean bench通风橱，fume cupboard药柜，Cupboard电泳电源，Electrophoresis power supply紫外灯，Ultraviolet illumination真空泵，Vacuum pump天平，balance/scale分析天平，analytical balance台秤，platform balance.涡旋振荡器，Vortexing machineCO2培养箱，CO2 Incubators电子显微镜，Electro Microscopy电泳仪，Electrophoresis System酶标仪，ELIASA恒流泵，constant flow pump解剖镜，anatomical lensPCR仪，Instrument for Polymerase Chain Reaction倒置显微镜，Inverted Microscope核磁共振波谱仪，Nuclear Magnetic Resonance Spectrometer 光学显微镜，Optical Microscopy摇床，Shaker培养箱，incubator超滤器，Ultrahigh Purity Filter超低温冰箱，Ultra-low Temperature Freezer超声破碎仪，Ultrasonic Cell Disruptor紫外观察灯，Ultraviolet Lamp紫外-可见光分光光度计，UV-Visible Spectrophotometer 计算器，calculator/numerator丙氨酸，alanine (Ala, A)缬氨酸，valine (Val, V)亮氨酸，leucine (Leu, L)异亮氨酸，isoleucine (Ile,I)脯氨酸，proline (Pro, P)苯丙氨酸，phenylalanine (Phe, F)色氨酸，tryptophan (Trp, W)蛋氨酸，methionine (Met, M)甘氨酸，glycine (Gly, G). 丝氨酸，serine (Ser, S)苏氨酸，threonine (Thr, T)半胱氨酸，cysteine (Cys, C)酪氨酸，tyrosine (Tyr, Y)天冬氨酸，asparagines (Asn, N)谷氨酰胺，glutamine (Gln, Q)赖氨酸，lysine (Lys, K)精氨酸，arginine (Arg, R)组氨酸，histidine (His, H)天冬氨酸，aspartic acid (Asp, D)谷氨酸，glutamic acid (Glu, E)腺苷，adenosine鸟嘌呤核苷，guanosine胞苷，cytidine胸腺嘧啶脱氧核苷，thymidine尿嘧啶核苷，uridine脱氧，deoxy-二甲苯，Xylene冰乙酸，Acetic acid glacial硼酸，Boric acid (H3BO3,61.83)氯化钙，Calcium chloride巯基乙醇，mercaptoethanol咪唑，Imidazole盐酸胍，guanidine hydrochloride无水乙醇，absolute ethanol乙酸钠，Sodium acetate氯化钠，Sodium chloride生理盐水，physiological saline洗涤剂，detergent十二烷基磺酸钠，Sodium dodecyl sulphate 盐酸，hydrochloric acid氢氧化钠，sodium hydrate/hydroxide胰蛋白胨，Tryptone酵母提取物，yeast extract琼脂，Agar两性霉素，amphotericin氨苄，Ampicillin肝素，heparin卡那霉素，Kanamycin醋酸钾，Potassium acetate异丙醇，Isopropanol醋酸铵，Ammonium acetate异戊醇，Isoamyl alcohol氯仿，Chloroform甲醇，methanol高锰酸钾，potassium hypermanganate考马斯亮蓝，Coomassie brilliant blue液氮，liquid nitrogen次氯酸钠，clorox苯酚，phenol阴离子，anion碱性，alkalinity量杯，measuring cup烧杯，beaker不锈钢杯，stainless-steel beaker量筒，measuring flask/measuring cylinder 量筒，graduated flask/measuring cylinder 坩埚，crucible坩埚钳，crucible clamp坩埚，crucible pot, melting pot试管，test tube试管架，test tube holder漏斗，funnel分液漏斗，separatory funnel烧瓶，flask锥形瓶，conical flask塞子，stopper洗瓶，plastic wash bottle滴定管，burette玻璃活塞，stopcock冷凝器，condenser试剂瓶，reagent bottles玻棒，glass rod搅拌棒，stirring rod蒸馏烧瓶，distilling flask碘量瓶，iodine flask表面皿，watch glass蒸发皿，evaporating dish容量瓶，volumetric flask/measuring flask 移液管，(one-mark) pipette刻度移液管，graduated pipettes称量瓶，weighing bottle吸液管，pipette滤管，filter天平，balance/scale分析天平，analytical balance台秤，platform balance游码，crossbeams and sliding weights酒精灯，alcohol burner酒精喷灯，blast alcohol burner搅拌装置，stirring device洗耳球，rubber suction bulb研磨钵，mortar研磨棒，pestle玛瑙研钵，agate mortar瓷器，porcelain白细口瓶，flint glass solution bottle with stopper滴瓶，dropping bottle小滴管，dropper蒸馏装置，distilling apparatus蒸发器，evaporator试验用器材：升降台，lab jack铁架台，iron support万能夹，extension clamp蝴蝶夹，double-buret clamp双顶丝，clamp regular holder止水夹，flatjaw pinchcock圆形漏斗架，cast-iron ring移液管架，pipet rack试管架，tube rack沸石，boiling stone橡胶管，rubber tubing药匙，lab spoon镊子，forceps坩埚钳，crucible tong剪刀，scissor打孔器，stopper borer石棉网，asbestos-free wire gauze电炉丝，wire coil for heater脱脂棉，absorbent cottonphph试纸，universal ph indicator paper滤纸，filter paper称量纸，weighing paper擦镜纸，wiper for lens秒表，stopwatch量杯，glass graduates with scale白滴定管（酸），flint glass burette with glass stopcock棕色滴定管（酸），brown glass burette with glass stopcock 白滴定管（碱），flint glass burette for alkali棕色滴定管（碱），brown glass burette for alkali比重瓶，specific gravity bottle水银温度计，mercury-filled thermometerph计，ph meter折光仪，refractometer真空泵，vacuum pump冷、热浴，bath离心机，centrifuge口罩，respirator防毒面具，respirator、gasmask磁力搅拌器，magnetic stirrer电动搅拌器，power basic stirrer烘箱，oven闪点仪，flash point tester马弗炉，furnace电炉，heater微波炉电热套，heating mantleBunsen burner，本生灯product，化学反应产物apparatus，设备PH indicator ，PH值指示剂,氢离子(浓度的)负指数指示剂matrass ，卵形瓶litmus，石蕊litmus paper，石蕊试纸burette，滴定管retort，曲颈甑still ，蒸馏釜cupel，烤钵化学反应：analysis，分解fractionation，分馏endothermic reaction ，吸热反应exothermic reaction ，放热反应precipitation ，沉淀to precipitate ，沉淀to distil, to distill，蒸馏distillation，蒸馏to calcine，煅烧to oxidize ，氧化alkalinization，碱化to oxygenate, to oxidize ，脱氧,氧化to neutralize，中和to hydrogenate，氢化to hydrate ，水合,水化to dehydrate，脱水fermentation，发酵solution ，溶解combustion，燃烧fusion, melting，熔解alkalinity ，碱性isomerism, isomery ，同分异物现象hydrolysis ，水解electrolysis ，电解electrode，电极anode ，阳极,正极cathode ，阴极,负极catalyst ，催化剂catalysis ，催化作用oxidization/oxidation，氧化reducer，还原剂dissolution ，分解synthesis ，合成reversible ，可逆的仪器中英文对照Aging Property Tester，老化性能测定仪Amino Acid Analyzer ，氨基酸组成分析仪Analyzer for Clinic Medicine Concentration ，临床药物浓度仪Atomic Absorption Spectroscopy ，原子吸收光谱仪Atomic Emission Spectrometer ，原子发射光谱仪Atomic Fluorescence Spectroscopy，原子荧光光谱仪Automatic Titrator ，自动滴定仪Basic Physics ，基本物理量测定Biochemical Analyzer，生化分析仪Biochemicalanalysis，生物技术分析Bio-reactor ，生物反应器Blood-gas Analyzer ，血气分析仪Centrifuge ，离心机ChemiluminescenceApparatus ，化学发光仪CHN Analysis ，环境成分分析仪CO2 Incubators CO2，培养箱Combustion PropertyTester ，燃烧性能测定仪Conductivity Meter ，电导仪Constant Temperature Circulator ，恒温循环泵Direct Current Plasma Emission Spectrometer ，直流等离子体发射光谱仪DNA Sequencers DNA，测序仪DNA synthesizer DNA，合成仪Electrical Property Tester ，电性能测定仪Electro Microscopy，电子显微镜Electrolytic Analyzer ，电解质分析仪Electron Energy Disperse Spectroscopy，电子能谱仪Electron Paramagnetic ResonanceSpectrometer ，电子顺磁共振波谱仪Electrophoresis ，电泳Electrophoresis System ，电泳仪ELIASA ，酶标仪Energy Disperse Spectroscopy ，能谱仪Fermenter ，发酵罐Flow Analytical and Process AnalyticalChemistry ，流动分析与过程分析Fraction Collector ，部分收集器FreezeDrying Equipment，冻干机FT-IR Spectrometer ，傅里叶变换红外光谱仪FT-Raman Spectrometer ，傅里叶变换拉曼光谱仪Gas Analysis ，气体分析Gas Chromatograph ，气相色谱仪GC-MS ，气相色谱-质谱联用仪Gel PermeationChromatograph ，凝胶渗透色谱仪HighPressure/Performance Liquid Chromatography ，高压/效液相色谱仪Hybridization Oven，分子杂交仪ICP-MS，ICP-质谱联用仪Inductive Coupled Plasma Emission Spectrometer ，电感偶合等离子体发射光谱仪Instrument for Nondestructive Testing，无损检测仪Instrument for Polymerase Chain Reaction，PCR仪Inverted Microscope ，倒置显微镜Ion Chromatograph ，离子色谱仪Isotope X-Ray Fluorescence Spectrometer ，同位素X荧光光谱仪LC-MS ，液相色谱-质谱联用仪Mass Spectrometer ，质谱仪Mechanical Property Tester ，机械性能测定仪Metal/material elemental analysis ，金属/材料元素分析仪Metallurgical Microscopy ，金相显微镜Microwave Inductive Plasma Emission Spectrometer ，微波等离子体光谱仪Nuclear Magnetic Resonance Spectrometer ，核磁共振波谱仪Optical Microscopy ，光学显微镜Optical PropertyTester ，光学性能测定仪Other/Miscellaneous ，其他Particle Size Analyzer ，粒度分析仪PCR Amplifier PCR，仪Peptide synthesizer，多肽合成仪pH Meter ，pH计PhysicalProperty Analysis ，物性分析Polarograph ，极谱仪Protein Sequencer ，氨基酸测序仪Rheometer ，流变仪Sample Handling ，样品处理Scanning Probe Microscopy ，扫描探针显微镜Sensors ，传感器Sequencers and Synthesizers for DNA and Protein DNA，及蛋白质的测序和合成仪Shaker ，摇床Size Exclusion Chromatograph ，体积排阻色谱Surface Science ，表面科学SurfaceAnalyzer ，表面分析仪Thermal Analyzer，热分析仪Thermal Physical Property Tester，热物理性能测定仪Ultrahigh Purity Filter，超滤器Ultra-low Temperature Freezer，超低温冰箱Ultrasonic Cell Disruptor ，超声破碎仪Ultraviolet Detector ，紫外检测仪UltravioletLamp ，紫外观察灯Urine Analyzer ，尿液分析仪UV-Visible Spectrophotometer ，紫外-可见光分光光度计Viscometer ，粘度计Voltammerter ，伏安仪Water Test Kits ，水质分析仪X-Ray Fluorescence Spectrometer ，X射线荧光光谱仪X-RayDiffractomer，X射线衍射仪如有侵权请联系告知删除，感谢你们的配合！。

当你进入国外的实验室之前，如果不能熟练掌握实验过程中相关物品的英文名称及读音，你与同处一室的技术人员之间必将产生强烈的交流障碍，实验效率也将因此大打折扣。

这里我汇总了数篇文章的相关内容，并结合自己实验室的情况，补充了大量词汇，希望对即将出国留学的生物学科研人员有所帮助。

欢迎大家补充指正。

一．容器与耗材（vessel & consumable material）小瓶，vial量杯，measuring cup烧杯，beaker量筒，measuring flask量筒，measuring cylinderer坩埚，crucible坩埚钳，crucible clamp试管，test tube漏斗，funnel比色皿，cuvette鱼缸，aquarium烧瓶，flask锥形瓶，conical flask塞子，stopper/plug洗瓶，plastic wash bottle玻璃活塞，stopcock试剂瓶，reagent bottles玻棒，glass rod搅拌棒，stirring rod容量瓶，volumetric flask/measuring flask移液管，(one-mark) pipette 吸液管，pipette滤器，filter滤纸，filter paper培养皿，culture dish移液枪，pipette移液枪枪头，pipette tips剃刀刀片，razor blade手术刀，scalpel垃圾袋，disposable bag垃圾桶，garbage bin橡皮筋，rubber band托盘，Tray铝箔，aluminium foil洗耳球，rubber suction bulb 保鲜膜，preservative film研磨钵，mortar研杵，pestle小滴管，dropper蒸馏装置，distilling apparatus 桶，bucket广口瓶，wide-mouth bottle离心机转子，rotor试管架，test tube holder/rack 酒精灯，alcohol burner酒精喷灯，blast alcohol burner 搅拌装置，stirring device石蜡封口膜，Parafilm微量离心管（EP管），Eppendorf tube 载玻片，Slide盖玻片，Cover glass离心管，Centrifuge tube电泳槽，Gel tank电线，Electrical leads牙签，Toothpick螺丝钉，Screw锁紧螺母，Nut, Cap nut复印纸，Copy paper复写纸，Carbon paper钉，Nail试管刷，test-tube brush计时器，Timer闹钟，Alarm clockU形钉，Staple衣服挂钩，Coat hanger电泳用的梳子，Comb扳手，Shifting spanner订书机，Stapler订书钉，staple圆珠笔芯，Refill灯泡，Globe记号笔，marker pen注射器，syringe注射器活塞，plunger铁架台，iron support万能夹，extension clamp止水夹，flatjaw pinchcock圆形漏斗架，cast-iron ring橡胶管，rubber tubing药匙，lab spoon镊子，forceps剪刀，scissor打孔器，stopper borerpH试纸，universal ph indicator paper 称量纸，weighing paper擦镜纸，wiper for lens水银温度计，mercury-filled thermometer 真空泵，vacuum pump水浴锅，water bath kettle口罩，respirator电极，electrode阳极/正极，anode阴极/负极，cathode丢弃，discard转移容器，decant吸出，aspirate吹吸，blowing and suction离心收集，pellet重悬，resuspend絮状沉淀，flocculent precipitate浑浊的，turbid烘，bake灭菌，sterilize培养，foster通风，ventilate冷却，chill down稀释，dilute洗脱，elute孵育，incubate裂解物，Lysate沉淀物，Sediment上清，Supernatant色谱，chromatograph 沉淀，precipitate接种，inoculate蒸馏，distil/distill搅拌，Stir/agitate中和，neutralize漂洗，rinse脱水，dehydrate发酵，fermentation溶解，dissolve燃烧，combustion水解，hydrolysis过滤，filtrate催化剂，catalyst研磨，grind破碎，crush催化作用，catalysis分解，dissolution涡旋震荡，Vortex电泳，Electrophoresis抽滤，suction filtration电转化，electrotransformation收菌，harvest切碎，chop/mince灌注，perfusion浆液，slurry恒温循环仪，Thermostatic circulator空调机，Air conditionerpH计，pH meter磁力搅拌器，magnetic stirrer烘箱，oven微波炉，microwave oven电磁炉，electromagnetic oven凝胶系统，Gel system电子天平，Electronic balance转接器，Adapter离心机，centrifuge封口设备，Sealing equipment复印机，Duplicator, copying machine超净工作台，super clean bench通风橱，fume cupboard药柜，Cupboard电泳电源，Electrophoresis power supply 紫外灯，Ultraviolet illumination真空泵，Vacuum pump天平，balance/scale分析天平，analytical balance台秤，platform balance涡旋振荡器，Vortexing machineCO2培养箱，CO2 Incubators电子显微镜，Electro Microscopy电泳仪，Electrophoresis System酶标仪，ELIASA恒流泵，constant flow pump解剖镜，anatomical lensPCR仪，Instrument for Polymerase Chain Reaction倒置显微镜，Inverted Microscope核磁共振波谱仪，Nuclear Magnetic Resonance Spectrometer 光学显微镜，Optical Microscopy摇床，Shaker培养箱，incubator超滤器，Ultrahigh Purity Filter超低温冰箱，Ultra-low Temperature Freezer超声破碎仪，Ultrasonic Cell Disruptor紫外观察灯，Ultraviolet Lamp紫外-可见光分光光度计，UV-Visible Spectrophotometer计算器，calculator/numerator丙氨酸，alanine (Ala, A)缬氨酸，valine (Val, V)亮氨酸，leucine (Leu, L)异亮氨酸，isoleucine (Ile,I)脯氨酸，proline (Pro, P)苯丙氨酸，phenylalanine (Phe, F)色氨酸，tryptophan (Trp, W)蛋氨酸，methionine (Met, M)甘氨酸，glycine (Gly, G)丝氨酸，serine (Ser, S)苏氨酸，threonine (Thr, T)半胱氨酸，cysteine (Cys, C)酪氨酸，tyrosine (Tyr, Y)天冬氨酸，asparagines (Asn, N) 谷氨酰胺，glutamine (Gln, Q)赖氨酸，lysine (Lys, K)精氨酸，arginine (Arg, R)组氨酸，histidine (His, H)天冬氨酸，aspartic acid (Asp, D) 谷氨酸，glutamic acid (Glu, E) 腺苷，adenosine鸟嘌呤核苷，guanosine胞苷，cytidine胸腺嘧啶脱氧核苷，thymidine尿嘧啶核苷，uridine脱氧，deoxy-二甲苯，Xylene冰乙酸，Acetic acid glacial硼酸，Boric acid (H3BO3,61.83) 氯化钙，Calcium chloride巯基乙醇，mercaptoethanol咪唑，Imidazole盐酸胍，guanidine hydrochloride 无水乙醇，absolute ethanol乙酸钠，Sodium acetate氯化钠，Sodium chloride生理盐水，physiological saline洗涤剂，detergent十二烷基磺酸钠，Sodium dodecyl sulphate 盐酸，hydrochloric acid氢氧化钠，sodium hydrate/hydroxide胰蛋白胨，Tryptone酵母提取物，yeast extract琼脂，Agar两性霉素，amphotericin氨苄，Ampicillin肝素，heparin卡那霉素，Kanamycin醋酸钾，Potassium acetate异丙醇，Isopropanol醋酸铵，Ammonium acetate异戊醇，Isoamyl alcohol氯仿，Chloroform甲醇，methanol高锰酸钾，potassium hypermanganate考马斯亮蓝，Coomassie brilliant blue液氮，liquid nitrogen次氯酸钠，clorox苯酚，phenol阴离子，anion碱性，alkalinity量杯，measuring cup烧杯，beaker不锈钢杯，stainless-steel beaker量筒，measuring flask/measuring cylinder 量筒，graduated flask/measuring cylinder 坩埚，crucible坩埚钳，crucible clamp坩埚，crucible pot, melting pot试管，test tube试管架，test tube holder漏斗，funnel分液漏斗，separatory funnel烧瓶，flask锥形瓶，conical flask塞子，stopper洗瓶，plastic wash bottle滴定管，burette玻璃活塞，stopcock冷凝器，condenser试剂瓶，reagent bottles玻棒，glass rod搅拌棒，stirring rod蒸馏烧瓶，distilling flask碘量瓶，iodine flask表面皿，watch glass蒸发皿，evaporating dish容量瓶，volumetric flask/measuring flask 移液管，(one-mark) pipette刻度移液管，graduated pipettes称量瓶，weighing bottle吸液管，pipette滤管，filter天平，balance/scale分析天平，analytical balance台秤，platform balance游码，crossbeams and sliding weights酒精灯，alcohol burner酒精喷灯，blast alcohol burner搅拌装置，stirring device洗耳球，rubber suction bulb研磨钵，mortar研磨棒，pestle玛瑙研钵，agate mortar瓷器，porcelain白细口瓶，flint glass solution bottle with stopper滴瓶，dropping bottle小滴管，dropper蒸馏装置，distilling apparatus蒸发器，evaporator试验用器材：升降台，lab jack铁架台，iron support万能夹，extension clamp蝴蝶夹，double-buret clamp双顶丝，clamp regular holder止水夹，flatjaw pinchcock圆形漏斗架，cast-iron ring移液管架，pipet rack试管架，tube rack沸石，boiling stone橡胶管，rubber tubing药匙，lab spoon镊子，forceps坩埚钳，crucible tong剪刀，scissor打孔器，stopper borer石棉网，asbestos-free wire gauze电炉丝，wire coil for heater脱脂棉，absorbent cottonphph试纸，universal ph indicator paper滤纸，filter paper称量纸，weighing paper擦镜纸，wiper for lens秒表，stopwatch量杯，glass graduates with scale白滴定管（酸），flint glass burette with glass stopcock棕色滴定管（酸），brown glass burette with glass stopcock 白滴定管（碱），flint glass burette for alkali棕色滴定管（碱），brown glass burette for alkali比重瓶，specific gravity bottle水银温度计，mercury-filled thermometerph计，ph meter折光仪，refractometer真空泵，vacuum pump冷、热浴，bath离心机，centrifuge口罩，respirator防毒面具，respirator、gasmask磁力搅拌器，magnetic stirrer电动搅拌器，power basic stirrer烘箱，oven闪点仪，flash point tester马弗炉，furnace电炉，heater微波炉电热套，heating mantleBunsen burner，本生灯product，化学反应产物apparatus，设备PH indicator ，PH值指示剂,氢离子(浓度的)负指数指示剂matrass ，卵形瓶litmus，石蕊litmus paper，石蕊试纸burette，滴定管retort，曲颈甑still ，蒸馏釜cupel，烤钵化学反应：analysis，分解fractionation，分馏endothermic reaction ，吸热反应exothermic reaction ，放热反应precipitation ，沉淀to precipitate ，沉淀to distil, to distill，蒸馏distillation，蒸馏to calcine，煅烧to oxidize ，氧化alkalinization，碱化to oxygenate, to oxidize ，脱氧,氧化to neutralize，中和to hydrogenate，氢化to hydrate ，水合,水化to dehydrate，脱水fermentation，发酵solution ，溶解combustion，燃烧fusion, melting，熔解alkalinity ，碱性isomerism, isomery ，同分异物现象hydrolysis ，水解electrolysis ，电解electrode，电极anode ，阳极,正极cathode ，阴极,负极catalyst ，催化剂catalysis ，催化作用oxidization/oxidation，氧化reducer，还原剂dissolution ，分解synthesis ，合成reversible ，可逆的仪器中英文对照Aging Property Tester，老化性能测定仪Amino Acid Analyzer ，氨基酸组成分析仪Analyzer for Clinic Medicine Concentration ，临床药物浓度仪Atomic Absorption Spectroscopy ，原子吸收光谱仪Atomic Emission Spectrometer ，原子发射光谱仪Atomic Fluorescence Spectroscopy，原子荧光光谱仪Automatic Titrator ，自动滴定仪Basic Physics ，基本物理量测定Biochemical Analyzer，生化分析仪Biochemicalanalysis，生物技术分析Bio-reactor ，生物反应器Blood-gas Analyzer ，血气分析仪Centrifuge ，离心机ChemiluminescenceApparatus ，化学发光仪CHN Analysis ，环境成分分析仪CO2 Incubators CO2，培养箱Combustion PropertyTester ，燃烧性能测定仪Conductivity Meter ，电导仪Constant Temperature Circulator ，恒温循环泵Direct Current Plasma Emission Spectrometer ，直流等离子体发射光谱仪DNA Sequencers DNA，测序仪DNA synthesizer DNA，合成仪Electrical Property Tester ，电性能测定仪Electro Microscopy，电子显微镜Electrolytic Analyzer ，电解质分析仪Electron Energy Disperse Spectroscopy，电子能谱仪Electron Paramagnetic ResonanceSpectrometer ，电子顺磁共振波谱仪Electrophoresis ，电泳Electrophoresis System ，电泳仪ELIASA ，酶标仪Energy Disperse Spectroscopy ，能谱仪Fermenter ，发酵罐Flow Analytical and Process AnalyticalChemistry ，流动分析与过程分析Fraction Collector ，部分收集器FreezeDrying Equipment，冻干机FT-IR Spectrometer ，傅里叶变换红外光谱仪FT-Raman Spectrometer ，傅里叶变换拉曼光谱仪Gas Analysis ，气体分析Gas Chromatograph ，气相色谱仪GC-MS ，气相色谱-质谱联用仪Gel PermeationChromatograph ，凝胶渗透色谱仪HighPressure/Performance Liquid Chromatography ，高压/效液相色谱仪Hybridization Oven，分子杂交仪ICP-MS，ICP-质谱联用仪Inductive Coupled Plasma Emission Spectrometer ，电感偶合等离子体发射光谱仪Instrument for Nondestructive Testing，无损检测仪Instrument for Polymerase Chain Reaction，PCR仪Inverted Microscope ，倒置显微镜Ion Chromatograph ，离子色谱仪Isotope X-Ray Fluorescence Spectrometer ，同位素X荧光光谱仪LC-MS ，液相色谱-质谱联用仪Mass Spectrometer ，质谱仪Mechanical Property Tester ，机械性能测定仪Metal/material elemental analysis ，金属/材料元素分析仪Metallurgical Microscopy ，金相显微镜Microwave Inductive Plasma Emission Spectrometer ，微波等离子体光谱仪Nuclear Magnetic Resonance Spectrometer ，核磁共振波谱仪Optical Microscopy ，光学显微镜Optical PropertyTester ，光学性能测定仪Other/Miscellaneous ，其他Particle Size Analyzer ，粒度分析仪PCR Amplifier PCR，仪Peptide synthesizer，多肽合成仪pH Meter ，pH计PhysicalProperty Analysis ，物性分析Polarograph ，极谱仪Protein Sequencer ，氨基酸测序仪Rheometer ，流变仪Sample Handling ，样品处理Scanning Probe Microscopy，扫描探针显微镜Sensors ，传感器Sequencers and Synthesizers for DNA and Protein DNA，及蛋白质的测序和合成仪Shaker ，摇床Size Exclusion Chromatograph ，体积排阻色谱Surface Science ，表面科学SurfaceAnalyzer ，表面分析仪Thermal Analyzer，热分析仪Thermal Physical Property Tester，热物理性能测定仪Ultrahigh Purity Filter，超滤器Ultra-low Temperature Freezer，超低温冰箱Ultrasonic Cell Disruptor ，超声破碎仪Ultraviolet Detector ，紫外检测仪UltravioletLamp ，紫外观察灯Urine Analyzer ，尿液分析仪UV-Visible Spectrophotometer ，紫外-可见光分光光度计Viscometer ，粘度计Voltammerter ，伏安仪Water Test Kits ，水质分析仪X-Ray Fluorescence Spectrometer ，X射线荧光光谱仪X-RayDiffractomer，X射线衍射仪。

螺旋线 helix螺纹 screw thread圆柱螺纹 parallel screw thread圆锥螺纹 taper screw thread外螺纹 external thread内螺纹 internal thread单线螺纹 single-start thread多线螺纹 multi-start thread右旋螺纹 right-hand thread左旋螺纹 left-hand thread自攻螺纹 tapping screw thread基本牙型 basic profile牙型角 thread angle牙型半角 half of thread angle公称直径 nominal diameter螺纹大径 major diameter螺纹小径 minor diameter螺纹中径 pitch diameter螺距 pitch螺纹导程 lead螺纹升角 lead angle螺纹牙厚 thread ridge thickness螺纹槽宽 thread groove width螺纹旋合长度 length of thread engagement螺纹接触高度 thread contact height螺距偏差 deviation in pitch螺距累积误差 cumulative error in pitch螺栓 bolt双头螺柱 stud六角头螺栓 hexagon bolt地脚螺栓 foundation boltT形螺栓 T-head bolt , hammer head bolt螺钉 screw紧定螺钉 set screw自攻螺钉 tapping screw吊环螺钉 lifting eye bolt开槽圆柱头螺钉 slotted cheese head screw开槽盘头螺钉 slotted pan head screw开槽沉头螺钉 slotted countersunk (flat) head screw开槽半沉头螺钉 slotted raised countersunk (oval) head screw开槽圆头螺钉 slotted round head screw内六角圆柱头螺钉 hexagon socket head cap head screw内六角沉头螺钉 hexagon socket countersunk head cap head screw 十字槽盘头螺钉 cross recessed pan head screw十字槽沉头螺钉 cross recessed countersunk head screw螺母 nut六角螺母 hexagon nut方螺母 square nut圆螺母 round nut滚花高螺母 knurled nut with collar翼形螺母 wing nut吊环螺母 lifting nut螺纹牙型thread tooth profile三角形螺纹triangular thread矩形螺纹square thread梯形螺纹trapezoidal (acme) thread锯齿形螺纹buttress thread外(阳)螺纹 ex ternal (male) thread内(阴)螺纹 in ternal (female) thread倒角chamfer球头round heads平头flat heads螺尾thread runout退刀(越程)槽undercut车外螺纹external thread lathing车内螺纹internal thread lathing套外螺纹covering external threadtapping钻孔drilling铰孔reaming通孔through hole盲孔blind hole螺纹盲孔blind threaded hole麻花钻twist drill钻头角point angle螺纹终止线thread end line公称直径nominal diameter螺纹大径major diameter螺纹小径 m inor diameter螺纹中径pitch (effective) diameter牙底root牙顶crest螺距pitch导程lead旋向revolving direction螺纹角thread angle右旋螺纹right hand-thread左旋螺纹left hand-threadclockwise逆时针方向anti-clockwise线数number of starts单线螺纹single-start thread双线螺纹double-start thread多线螺纹multiple thread标准螺纹standard screw非标准螺纹nonstandard screw特殊螺纹special thread粗牙普通螺纹coarse pitch thread细牙普通螺纹fine pitch thread螺纹规格screw size普通(公制)螺纹general (metric) thread管螺纹pipe thread圆柱内管螺纹parallel internal pipe thread圆锥内管螺纹taper internal pipe thread圆柱外管螺纹parallel external pipe thread圆锥外管螺纹taper external pipe thread小螺纹mini thread传动螺纹transmission thread558非密封管螺纹558 non-sealing pipe thread558密封管螺纹558 sealing pipe thread608 sealing pipe thread米制锥螺纹metric taper thread自攻螺钉螺纹self-drilling screw thread木螺钉螺纹wooden nail thread气瓶专用螺纹thread for gas tanke螺纹紧固件screw fasteners螺纹旋合长度 length of thread engagement中旋合长度thread engagement group-normal螺栓bolt六角头螺栓hexagon head bolt双头螺柱stud有效长度effective length旋入(机件)端metal end露出端(旋螺母端) nut end螺栓联接bolt joint螺柱联接stud joint螺钉联接screw joint螺钉screw紧定螺钉set screw开槽球头螺钉slotted round head screw开槽圆柱头螺钉slotted cheese head screwslotted pan head screw开槽沉头螺钉slotted countersunk screw十字槽沉头螺钉philips countersunk screw内圆柱头六角螺钉 socket cap screw 开槽锥端紧定螺钉 slotted cone pointed set screw开槽平端紧定螺slotted flat point set screw开槽长圆柱端紧定螺钉s lotted dog point set screw螺母nut六角螺母hex nut六角薄螺母hexagon thin nut内六角圆螺母castle nut六角开槽螺母hex slotted nutI型六角螺母A级和B级grade A and grade B of type onehexagon nut垫圈（片）washer or spacer平垫圈bright washer平垫圈倒角型chamfer bright washer小垫圈small washer大垫圈big washer特大垫圈very big washer-grade弹簧垫圈spring (lock)washer标准型弹簧垫圈standard spring washerlight type spring washer重型弹簧垫圈heavy type spring washer外舌止动垫圈tab washer齿轮gear轮毂hub轮辐spoke标准齿轮standard gear渐开线齿轮involute gear直齿圆柱齿轮 spur gear斜齿轮helical gear锥(伞)齿轮bevel gear人字齿轮herringbone wheel蜗轮worm wheel蜗杆worm相交轴intersecting shaft主动(小齿)轮pinion从动(大齿)轮follower gear齿顶圆addendum circle齿根圆dedendum circle节圆（分度圆）直径 pitch circle diameter节点pitch point齿顶高addendum齿根高dedendum齿高total depth齿厚tooth thickness槽宽width of space齿距circular pitch齿宽tooth width齿数number of teeth模数module压力角pressure angle销pin圆柱销parallel (dowel) pin圆锥销taper pin开口(尾)销split cotter pin销联接pin joint键key普通平键parallel key圆头普通平键round end parallel key方头普通平键square parallel key单圆头普通平键single round parallel key 半圆键woodruff key钩头楔键gib head（taper）key花键spline键槽key way (slot)键联结key joint弹簧spring簧丝直(线)径wire diameter of spring弹簧外径external diameter弹簧内径internal diameter弹簧中径effective diameter弹簧节距pitch支承圈数number of end coils有效圈数number of active coils总圈数number of total coils自由高度free height弹簧丝展开长度stretched length of wire螺旋压缩弹簧helical compression spring螺旋拉伸弹簧helical extension spring螺旋扭转弹簧helical torsion spring涡卷弹簧turbination spring板簧leaf spring片簧blade spring轴承bearing滚动轴承rolling bearing内圈inner race外圈outer race滚动体rolling element保持架、隔离圈 cage 深沟球轴承deep groove ball bearing推力球轴承thrust ball bearing圆锥滚子轴承taper roller bearing上轴瓦top shell下轴瓦bottom shell。

螺丝钉:lag spike调整螺丝:plusminus screw尖端螺丝:pointed screw螺丝板牙:screw die螺丝灯头:screw holder螺丝车床:screw-cutting lath自攻螺丝:self tapping screw肩部螺丝:shoulder bolt止付螺丝:stop screw攻螺丝机:tapping machines螺丝车床:thread-cutting lath螺母螺丝攻:nut tap平头木螺丝:flat-head wood screw半圆头螺丝:half-round head screw电动螺丝刀:electric screw driver方头木螺丝:log screw螺丝，螺纹:screw thread十字头螺丝刀:screw driver for cross recessed screw爱迪生螺丝灯头:Edison screw-cap爱迪生螺丝插座:Edison screw-holder螺丝灯头，螺丝帽:screw cap螺丝夹，螺旋夹具:screw clamp螺栓，螺帽及螺丝:bolts screws机械螺丝用六角螺帽:hex machine screw nut止付螺丝，固定螺丝:set screw螺纹梳刀，螺丝花刀:thread chaser螺纹车床，螺丝车床:thread chasing machine螺口灯头，螺丝灯头:screw socket螺纹车床，螺丝车床:thread-cutting machine蝶形螺钉，大头螺丝:thumb screw虎钳丝杠，贯头螺丝:tommy screw手用螺丝攻，手用丝锥:hand tap滚丝机，螺丝滚压机床:thread rolling machine机用螺丝攻，螺母丝锥:leading tap方头木螺钉，方头木螺丝:coach screw锁紧(螺丝)，固定，紧固:fasten螺丝口龙头，螺丝攻，丝锥:screw tap旋凿，螺丝起子，传动丝杠:turn-screw螺纹孔，螺丝孔(有螺纹的):threaded hole螺丝孔(有螺纹的)，螺钉孔:screw hole十字形螺丝刀，十字螺丝起子:plus driver自动推进螺丝车床，自动车床:self-acting lath风动螺丝刀，风螺刀，气动起子:pneumatic screw driver 螺丝车床，螺纹铣床，螺丝磨床，螺纹磨床:threader改锥，螺丝刀，螺钉起子，旋凿，螺丝起子:screw driver①模具坯料，模体，块形模体②滑块，螺丝板甲牙:die block①螺丝，螺丝钉，螺杆，螺钉②螺旋桨③杆，六杆机构:screw①水龙头，丝锥，旋塞，螺丝攻，螺旋塞②抽头，分接头:tap①喷灯，喷嘴②螺纹接头，接头，螺纹接口(管)，螺丝管接头，管接头:nipple。

101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86 109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitchthread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitchthread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screwsISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screwsISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk headscrews ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk headscrews ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86 124 DIN975 牙条(全螺纹) threaded rods(studdings)GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽)grooved pins,taper grooved halflength ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN147 7沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87 164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17 170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washersassemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts onT-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618 179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutchlining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metricthread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85 193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical headsISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85 199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structuresGB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86 205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head woodscrews GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85 208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts)GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

螺钉的英文单词什么是螺钉？螺钉是一种常见的紧固件，通常由金属制成，具有螺纹的外形。

它通常用来连接两个或多个物体，并提供稳固的固定力。

螺钉通常由两个主要部分组成：螺纹部分和头部。

螺纹部分具有螺旋形的纹理，可以与其他物体的螺纹配合，形成牢固的连接。

头部通常用来旋转螺钉，使其进入或退出物体。

螺钉的英文单词是什么？螺钉的英文单词是”bolt”。

螺钉的分类螺钉可以根据不同的特征进行分类。

以下是一些常见的螺钉分类：1. 按照头部形状分类•平头螺钉（Flathead bolt）：头部呈平面形状，通常用于需要表面平整的场合。

•半圆头螺钉（Round head bolt）：头部呈半圆形状，通常用于需要较大的接触面积和抗拉力的场合。

•锥头螺钉（Countersunk bolt）：头部呈锥形状，可以嵌入物体表面，使其表面平整。

•六角头螺钉（Hex head bolt）：头部呈六角形状，可以使用扳手或扳手进行旋转。

2. 按照螺纹类型分类•全螺纹螺钉（Fully threaded bolt）：整个螺钉都具有螺纹，适用于需要更好的连接力和稳定性的场合。

•部分螺纹螺钉（Partially threaded bolt）：只有一部分螺钉具有螺纹，通常用于需要在特定位置提供稳定连接的场合。

3. 按照用途分类•机械螺钉（Machine bolt）：用于连接机械设备和结构的螺钉。

•木螺钉（Wood bolt）：用于连接木材的螺钉，通常具有较大的直径和较大的螺纹。

•自攻螺钉（Self-tapping bolt）：具有特殊的螺纹设计，可以在没有螺纹的孔中自行切割螺纹。

螺钉的应用领域螺钉在各个领域都有广泛的应用。

以下是一些常见的应用领域：1. 建筑和结构螺钉用于连接建筑和结构中的各种构件，如钢梁、钢柱和混凝土墙。

它们提供了强大的连接力，确保建筑物的稳定性和安全性。

2. 机械工程螺钉在机械工程中扮演着重要的角色。

它们用于连接不同的机械部件，如发动机、传动系统和轴承。

当你进入国外的实验室之前，如果不能熟练掌握实验过程中相关物品的英文名称及读音，你与同处一室的技术人员之间必将产生强烈的交流障碍，实验效率也将因此大打折扣。

这里我汇总了数篇文章的相关内容，并结合自己实验室的情况，补充了大量词汇，希望对即将出国留学的生物学科研人员有所帮助。

欢迎大家补充指正。

一．容器与耗材（vessel & consumable material）小瓶，vial量杯，measuring cup烧杯，beaker量筒，measuring flask量筒，measuring cylinderer坩埚，crucible坩埚钳，crucible clamp试管，test tube漏斗，funnel比色皿，cuvette鱼缸，aquarium烧瓶，flask锥形瓶，conical flask塞子，stopper/plug洗瓶，plastic wash bottle玻璃活塞，stopcock试剂瓶，reagent bottles玻棒，glass rod搅拌棒，stirring rod容量瓶，volumetric flask/measuring flask移液管，(one-mark) pipette 吸液管，pipette滤器，filter滤纸，filter paper培养皿，culture dish移液枪，pipette移液枪枪头，pipette tips剃刀刀片，razor blade手术刀，scalpel垃圾袋，disposable bag垃圾桶，garbage bin橡皮筋，rubber band托盘，Tray铝箔，aluminium foil洗耳球，rubber suction bulb 保鲜膜，preservative film研磨钵，mortar研杵，pestle小滴管，dropper蒸馏装置，distilling apparatus 桶，bucket广口瓶，wide-mouth bottle离心机转子，rotor试管架，test tube holder/rack 酒精灯，alcohol burner酒精喷灯，blast alcohol burner 搅拌装置，stirring device石蜡封口膜，Parafilm微量离心管（EP管），Eppendorf tube 载玻片，Slide盖玻片，Cover glass离心管，Centrifuge tube电泳槽，Gel tank电线，Electrical leads牙签，Toothpick螺丝钉，Screw锁紧螺母，Nut, Cap nut复印纸，Copy paper复写纸，Carbon paper钉，Nail试管刷，test-tube brush计时器，Timer闹钟，Alarm clockU形钉，Staple衣服挂钩，Coat hanger电泳用的梳子，Comb扳手，Shifting spanner订书机，Stapler订书钉，staple圆珠笔芯，Refill灯泡，Globe记号笔，marker pen注射器，syringe注射器活塞，plunger铁架台，iron support万能夹，extension clamp止水夹，flatjaw pinchcock圆形漏斗架，cast-iron ring橡胶管，rubber tubing药匙，lab spoon镊子，forceps剪刀，scissor打孔器，stopper borerpH试纸，universal ph indicator paper 称量纸，weighing paper擦镜纸，wiper for lens水银温度计，mercury-filled thermometer 真空泵，vacuum pump水浴锅，water bath kettle口罩，respirator电极，electrode阳极/正极，anode阴极/负极，cathode丢弃，discard转移容器，decant吸出，aspirate吹吸，blowing and suction离心收集，pellet重悬，resuspend絮状沉淀，flocculent precipitate浑浊的，turbid烘，bake灭菌，sterilize培养，foster通风，ventilate冷却，chill down稀释，dilute洗脱，elute孵育，incubate裂解物，Lysate沉淀物，Sediment上清，Supernatant色谱，chromatograph 沉淀，precipitate接种，inoculate蒸馏，distil/distill搅拌，Stir/agitate中和，neutralize漂洗，rinse脱水，dehydrate发酵，fermentation溶解，dissolve燃烧，combustion水解，hydrolysis过滤，filtrate催化剂，catalyst研磨，grind破碎，crush催化作用，catalysis分解，dissolution涡旋震荡，Vortex电泳，Electrophoresis抽滤，suction filtration电转化，electrotransformation收菌，harvest切碎，chop/mince灌注，perfusion浆液，slurry恒温循环仪，Thermostatic circulator空调机，Air conditionerpH计，pH meter磁力搅拌器，magnetic stirrer烘箱，oven微波炉，microwave oven电磁炉，electromagnetic oven凝胶系统，Gel system电子天平，Electronic balance转接器，Adapter离心机，centrifuge封口设备，Sealing equipment复印机，Duplicator, copying machine超净工作台，super clean bench通风橱，fume cupboard药柜，Cupboard电泳电源，Electrophoresis power supply 紫外灯，Ultraviolet illumination真空泵，Vacuum pump天平，balance/scale分析天平，analytical balance台秤，platform balance涡旋振荡器，Vortexing machineCO2培养箱，CO2 Incubators电子显微镜，Electro Microscopy电泳仪，Electrophoresis System酶标仪，ELIASA恒流泵，constant flow pump解剖镜，anatomical lensPCR仪，Instrument for Polymerase Chain Reaction倒置显微镜，Inverted Microscope核磁共振波谱仪，Nuclear Magnetic Resonance Spectrometer 光学显微镜，Optical Microscopy摇床，Shaker培养箱，incubator超滤器，Ultrahigh Purity Filter超低温冰箱，Ultra-low Temperature Freezer超声破碎仪，Ultrasonic Cell Disruptor紫外观察灯，Ultraviolet Lamp紫外-可见光分光光度计，UV-Visible Spectrophotometer计算器，calculator/numerator丙氨酸，alanine (Ala, A)缬氨酸，valine (Val, V)亮氨酸，leucine (Leu, L)异亮氨酸，isoleucine (Ile,I)脯氨酸，proline (Pro, P)苯丙氨酸，phenylalanine (Phe, F)色氨酸，tryptophan (Trp, W)蛋氨酸，methionine (Met, M)甘氨酸，glycine (Gly, G)丝氨酸，serine (Ser, S)苏氨酸，threonine (Thr, T)半胱氨酸，cysteine (Cys, C)酪氨酸，tyrosine (Tyr, Y)天冬氨酸，asparagines (Asn, N) 谷氨酰胺，glutamine (Gln, Q)赖氨酸，lysine (Lys, K)精氨酸，arginine (Arg, R)组氨酸，histidine (His, H)天冬氨酸，aspartic acid (Asp, D) 谷氨酸，glutamic acid (Glu, E) 腺苷，adenosine鸟嘌呤核苷，guanosine胞苷，cytidine胸腺嘧啶脱氧核苷，thymidine尿嘧啶核苷，uridine脱氧，deoxy-二甲苯，Xylene冰乙酸，Acetic acid glacial硼酸，Boric acid (H3BO3,61.83) 氯化钙，Calcium chloride巯基乙醇，mercaptoethanol咪唑，Imidazole盐酸胍，guanidine hydrochloride 无水乙醇，absolute ethanol乙酸钠，Sodium acetate氯化钠，Sodium chloride生理盐水，physiological saline洗涤剂，detergent十二烷基磺酸钠，Sodium dodecyl sulphate 盐酸，hydrochloric acid氢氧化钠，sodium hydrate/hydroxide胰蛋白胨，Tryptone酵母提取物，yeast extract琼脂，Agar两性霉素，amphotericin氨苄，Ampicillin肝素，heparin卡那霉素，Kanamycin醋酸钾，Potassium acetate异丙醇，Isopropanol醋酸铵，Ammonium acetate异戊醇，Isoamyl alcohol氯仿，Chloroform甲醇，methanol高锰酸钾，potassium hypermanganate考马斯亮蓝，Coomassie brilliant blue液氮，liquid nitrogen次氯酸钠，clorox苯酚，phenol阴离子，anion碱性，alkalinity量杯，measuring cup烧杯，beaker不锈钢杯，stainless-steel beaker量筒，measuring flask/measuring cylinder 量筒，graduated flask/measuring cylinder 坩埚，crucible坩埚钳，crucible clamp坩埚，crucible pot, melting pot试管，test tube试管架，test tube holder漏斗，funnel分液漏斗，separatory funnel烧瓶，flask锥形瓶，conical flask塞子，stopper洗瓶，plastic wash bottle滴定管，burette玻璃活塞，stopcock冷凝器，condenser试剂瓶，reagent bottles玻棒，glass rod搅拌棒，stirring rod蒸馏烧瓶，distilling flask碘量瓶，iodine flask表面皿，watch glass蒸发皿，evaporating dish容量瓶，volumetric flask/measuring flask 移液管，(one-mark) pipette刻度移液管，graduated pipettes称量瓶，weighing bottle吸液管，pipette滤管，filter天平，balance/scale分析天平，analytical balance台秤，platform balance游码，crossbeams and sliding weights酒精灯，alcohol burner酒精喷灯，blast alcohol burner搅拌装置，stirring device洗耳球，rubber suction bulb研磨钵，mortar研磨棒，pestle玛瑙研钵，agate mortar瓷器，porcelain白细口瓶，flint glass solution bottle with stopper滴瓶，dropping bottle小滴管，dropper蒸馏装置，distilling apparatus蒸发器，evaporator试验用器材：升降台，lab jack铁架台，iron support万能夹，extension clamp蝴蝶夹，double-buret clamp双顶丝，clamp regular holder止水夹，flatjaw pinchcock圆形漏斗架，cast-iron ring移液管架，pipet rack试管架，tube rack沸石，boiling stone橡胶管，rubber tubing药匙，lab spoon镊子，forceps坩埚钳，crucible tong剪刀，scissor打孔器，stopper borer石棉网，asbestos-free wire gauze电炉丝，wire coil for heater脱脂棉，absorbent cottonphph试纸，universal ph indicator paper滤纸，filter paper称量纸，weighing paper擦镜纸，wiper for lens秒表，stopwatch量杯，glass graduates with scale白滴定管（酸），flint glass burette with glass stopcock棕色滴定管（酸），brown glass burette with glass stopcock 白滴定管（碱），flint glass burette for alkali棕色滴定管（碱），brown glass burette for alkali比重瓶，specific gravity bottle水银温度计，mercury-filled thermometerph计，ph meter折光仪，refractometer真空泵，vacuum pump冷、热浴，bath离心机，centrifuge口罩，respirator防毒面具，respirator、gasmask磁力搅拌器，magnetic stirrer电动搅拌器，power basic stirrer烘箱，oven闪点仪，flash point tester马弗炉，furnace电炉，heater微波炉电热套，heating mantleBunsen burner，本生灯product，化学反应产物apparatus，设备PH indicator ，PH值指示剂,氢离子(浓度的)负指数指示剂matrass ，卵形瓶litmus，石蕊litmus paper，石蕊试纸burette，滴定管retort，曲颈甑still ，蒸馏釜cupel，烤钵化学反应：analysis，分解fractionation，分馏endothermic reaction ，吸热反应exothermic reaction ，放热反应precipitation ，沉淀to precipitate ，沉淀to distil, to distill，蒸馏distillation，蒸馏to calcine，煅烧to oxidize ，氧化alkalinization，碱化to oxygenate, to oxidize ，脱氧,氧化to neutralize，中和to hydrogenate，氢化to hydrate ，水合,水化to dehydrate，脱水fermentation，发酵solution ，溶解combustion，燃烧fusion, melting，熔解alkalinity ，碱性isomerism, isomery ，同分异物现象hydrolysis ，水解electrolysis ，电解electrode，电极anode ，阳极,正极cathode ，阴极,负极catalyst ，催化剂catalysis ，催化作用oxidization/oxidation，氧化reducer，还原剂dissolution ，分解synthesis ，合成reversible ，可逆的仪器中英文对照Aging Property Tester，老化性能测定仪Amino Acid Analyzer ，氨基酸组成分析仪Analyzer for Clinic Medicine Concentration ，临床药物浓度仪Atomic Absorption Spectroscopy ，原子吸收光谱仪Atomic Emission Spectrometer ，原子发射光谱仪Atomic Fluorescence Spectroscopy，原子荧光光谱仪Automatic Titrator ，自动滴定仪Basic Physics ，基本物理量测定Biochemical Analyzer，生化分析仪Biochemicalanalysis，生物技术分析Bio-reactor ，生物反应器Blood-gas Analyzer ，血气分析仪Centrifuge ，离心机ChemiluminescenceApparatus ，化学发光仪CHN Analysis ，环境成分分析仪CO2 Incubators CO2，培养箱Combustion PropertyTester ，燃烧性能测定仪Conductivity Meter ，电导仪Constant Temperature Circulator ，恒温循环泵Direct Current Plasma Emission Spectrometer ，直流等离子体发射光谱仪DNA Sequencers DNA，测序仪DNA synthesizer DNA，合成仪Electrical Property Tester ，电性能测定仪Electro Microscopy，电子显微镜Electrolytic Analyzer ，电解质分析仪Electron Energy Disperse Spectroscopy，电子能谱仪Electron Paramagnetic ResonanceSpectrometer ，电子顺磁共振波谱仪Electrophoresis ，电泳Electrophoresis System ，电泳仪ELIASA ，酶标仪Energy Disperse Spectroscopy ，能谱仪Fermenter ，发酵罐Flow Analytical and Process AnalyticalChemistry ，流动分析与过程分析Fraction Collector ，部分收集器FreezeDrying Equipment，冻干机FT-IR Spectrometer ，傅里叶变换红外光谱仪FT-Raman Spectrometer ，傅里叶变换拉曼光谱仪Gas Analysis ，气体分析Gas Chromatograph ，气相色谱仪GC-MS ，气相色谱-质谱联用仪Gel PermeationChromatograph ，凝胶渗透色谱仪HighPressure/Performance Liquid Chromatography ，高压/效液相色谱仪Hybridization Oven，分子杂交仪ICP-MS，ICP-质谱联用仪Inductive Coupled Plasma Emission Spectrometer ，电感偶合等离子体发射光谱仪Instrument for Nondestructive Testing，无损检测仪Instrument for Polymerase Chain Reaction，PCR仪Inverted Microscope ，倒置显微镜Ion Chromatograph ，离子色谱仪Isotope X-Ray Fluorescence Spectrometer ，同位素X荧光光谱仪LC-MS ，液相色谱-质谱联用仪Mass Spectrometer ，质谱仪Mechanical Property Tester ，机械性能测定仪Metal/material elemental analysis ，金属/材料元素分析仪Metallurgical Microscopy ，金相显微镜Microwave Inductive Plasma Emission Spectrometer ，微波等离子体光谱仪Nuclear Magnetic Resonance Spectrometer ，核磁共振波谱仪Optical Microscopy ，光学显微镜Optical PropertyTester ，光学性能测定仪Other/Miscellaneous ，其他Particle Size Analyzer ，粒度分析仪PCR Amplifier PCR，仪Peptide synthesizer，多肽合成仪pH Meter ，pH计PhysicalProperty Analysis ，物性分析Polarograph ，极谱仪Protein Sequencer ，氨基酸测序仪Rheometer ，流变仪Sample Handling ，样品处理Scanning Probe Microscopy，扫描探针显微镜Sensors ，传感器Sequencers and Synthesizers for DNA and Protein DNA，及蛋白质的测序和合成仪Shaker ，摇床Size Exclusion Chromatograph ，体积排阻色谱Surface Science ，表面科学SurfaceAnalyzer ，表面分析仪Thermal Analyzer，热分析仪Thermal Physical Property Tester，热物理性能测定仪Ultrahigh Purity Filter，超滤器Ultra-low Temperature Freezer，超低温冰箱Ultrasonic Cell Disruptor ，超声破碎仪Ultraviolet Detector ，紫外检测仪UltravioletLamp ，紫外观察灯Urine Analyzer ，尿液分析仪UV-Visible Spectrophotometer ，紫外-可见光分光光度计Viscometer ，粘度计Voltammerter ，伏安仪Water Test Kits ，水质分析仪X-Ray Fluorescence Spectrometer ，X射线荧光光谱仪X-RayDiffractomer，X射线衍射仪。

螺丝产品名称（螺丝螺）中英文对照六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺丝SQUARE HEAD BOLTST头螺丝T HEAD BOLTS马车螺丝CARRIAGE BOLTS环首螺丝EYE BOLTS内六角孔螺丝HEX SOCKET CAP SCREWS固定螺丝SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮壳螺栓WHEEL BOLTS翼形螺丝WING SCREWS自攻螺丝SELF TAPPING SCREWS自削螺丝THREAD CUTTING SCREWS钻尾螺丝SELF DRILLING SCREWS旋入螺丝DRIVE SCREWS机械螺丝MACHINE SCREWS木螺丝WOOD SCREWS家具螺丝FURNITURE SCREWS塑板螺丝CHIPBOARD SCREWS墙用螺丝DRYWALL SCREWS基础螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套挂螺丝TOGGLE BOLTS突缘螺丝FLANGE BOLTS轨道螺栓(鱼尾螺丝) TRACK BOLTS耐候钢螺丝CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓T.C.BOLTS高张力螺栓HIGH STRENGTH BOLTS剪力钉(焊接螺丝) WELDING STUDS螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓BIG SIZE BOLTS不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺丝STAINLESS STEEL BOLTS铜螺丝BRASS SCREWS铝螺丝ALUMINUM SCREWS合金钢螺丝ALLOY STEEL SCREWS电子螺丝ELECTRONIC SCREWS微小精密螺丝MICRO SCREWS塑胶螺丝PLASTIC SCREWS复合材料用螺丝PARTICLE BOARD SCREWS钛合金螺丝TITANIUM ALLOY BOLTS钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 拇指螺丝THUMB SCREWS双头牙螺丝DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS航太用螺丝AEROSPACE FASTENERS飞机特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺丝PANEL FASTENERS电梯螺丝ELEV A TOR BOLTS四角头固定螺丝SQUARE SET SCREWS大头马车螺丝STEP BOLTS单向螺丝ONE WAY LAG SCREWS管夹螺丝HOSE CLAMP SCREWS不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺丝HINGE SCREWS货柜螺丝CONTAINER SCREWS复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS三角牙螺丝TRILOBULAR THREAD SCREWS高低牙螺丝HIGH LOW SCREWS夹板用螺丝PARTICLE BOARD SCREWS马桶螺丝TOILET CLOSET BOLTS特长螺丝SPECIAL LONGER SCREWS建业螺丝BUILDING FASTENERS不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS 其它特殊螺丝SPECIAL SCREWS OR BOLTS不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS链带螺丝COLLATED SCREWS水泥螺丝CONCRETE SCREWS板模螺丝CONSTRUCTION BOLTS涞□萁z DIE CAST WING SCREWS; ZINC ALLOY重型车螺丝HEA VY DUTY WHEEL HUB BOLTS内六角固定螺丝HEX SOCKET SET SCREWS复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS犁壁螺丝PLOW BOLTS机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺丝SOCKET SET SCREWS不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS套挂螺栓及螺丝TOGGLE BOLTS钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS紧固件专业英语词汇UNF (美制细牙)UNEF (美制超细牙)B.S.W. 标准惠氏粗牙系列，一般用途圆柱螺纹B.S.F. 标准惠氏细牙系列，一般用途圆柱螺纹fine pitch thread 细牙full thread 全螺纹3 螺丝头型IHH=ind hex head 锯六角头PH=phillips 十字槽Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Cup head杯头4 常见紧固件名称split washer弹簧垫片（一般厂家会管washer叫“华司”）flat washer平垫片Self tapping screw自攻螺丝Self drilling screw自钻螺丝drywall screw 干墙螺丝/干壁螺丝/墙用螺丝high low screw高低牙螺丝collated screw链带螺丝Concrete screw 水泥螺丝Tri-lobular thread screw三角螺丝kep nut 锁紧螺母acorn nut 盖形螺母wing washer 翼型垫片eye bolt 吊环螺栓（也叫环首螺栓，其实这个叫法很多，大概是不同地区的缘故）Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts 六角头螺栓Hexagon flange bolts 六角法兰螺栓Carriage bolt 马车螺栓Square head bolt方头螺栓Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cross recessed pan head tapping screws 十字槽盘头自攻螺钉（如果在图纸上看到标注# 2或# 20等，是指该螺丝的头部适合2号或者20号的螺丝起子）5 表面处理方式BO=black oxide 氧化发黑（如果仅仅标注black,是指做染黑处理）Zinc plated 镀锌cementation 渗碳nylon patch耐落（刚看到的时候是直接按照字面翻译的“尼龙片”，拿给经理看的时候经理对照图纸看了半天跟我说你你去查下耐落的英文，果然---）6 其它图纸上可能出现的标注螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam内径ID= inner diameter外径OD= outside diameter通止规：Go/No go gage机械性能：mechanical and physical properties统一英制螺纹unified thread镀后去氢，防止氢脆Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement表面渗碳Case carburization对边With across flats对角With across corners头下圆角Radius of fillet过度螺纹Transition thread length扳拧高度Wrenching height洛氏硬度Rockwell维氏硬度Vickers布氏硬度Brinell机械性能8级P C 8 = property class 8机加工：Machining螺纹成型：Roll Threading热处理：heat treatment表面处理：finish（不过有时候也会标注成surface treatment）去氢：Lustrating hydrogen一. 螺纹种类:A: 三角螺纹( 60 度) : 结合/ 锁紧B: 管用三角螺纹( 55 度): 结合/ 锁紧C: 梯形螺纹( 30 or 29 度) : 动力传动D: 方螺纹( 90 度) : 动力传动二. 常用螺丝种类:A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝三. 常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜四. 常见螺丝规格与标示:A: 公制螺丝B: 美规螺丝C: 英制螺丝A: 公制机械螺丝: MetricEx: M3 x 6 – P P B : M3 机械螺丝, 6mm 长, 十字, 圆扁头, 镀黑. Finish Code: 外观处理规格Head Code: 头部外型Thread Code螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号公制螺丝直接以螺丝外径标示螺丝型号,如M3 即螺丝外径为3.00mm.; M4 即螺丝外径为4.00mm. Metric Thread Size x Pitch:Note: 公制螺丝于螺丝型号后方,有时会注明螺丝牙距.如M3x0.5 , M4x0.70, M5x0.8 , M6x1.但因为标准规范, 通常不提.A-2: Length Code: 螺丝长度:公制螺丝, 直接标示螺丝长度, 单位为mm.螺丝之总长度标示, 只计算头部以下之长度, 不含头部高度.但平头螺丝例外, 其螺丝之总长度标示含头部高度.A-3: Drive Code/ 头部剖沟,特征.一般常用规格如下:a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出)A-4: Head Code/ 头部外型.一般常用规格如下:a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头.A-5: Finish Code/ 外观处理.一般常用规格如下:a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理公制自攻螺丝:于品名后方直接标示Tapping Type.Ex: M3 x 6 –PPB, Tapping Type:M3 自攻螺丝, 6mm 长, 十字, 圆扁头, 镀黑.一般以产品别或标示, 再判断为Sheet Metal 或塑料部品使用. B: 美规螺丝.a.一般以番号标示, 如#2-56, #4-40, #6-32, #8-32, #10-24…etc.b.或以英制外径表示,如0.086-56, 0.112-40 , 0.138-32 , 0.164-32 , 0.190-24…etc. Ex: 632 – 8 – P P B:Finish Code: 外观处理规格Head Code: 头部外型Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度Thread Code: 螺丝型号B-1: Thread Code: 螺丝型号一般常用规格如下:a. #2-56 (0.086-56): 2 番56 牙b #4-40 (0.112-40) : 4 番40 牙c. #6-32 (0.138-32) : 6 番32 牙d. #8-32 (0.164-32) : 8 番32 牙e. #10-24 (0.190-24): 10 番24 牙***牙为每吋之牙数.***B-2: Length Code: 螺丝长度美规螺丝长度须经换算, 才是公制mm 尺寸.换算公式: (Length Code / 32) x 25.40 = 公制长度mmB-3, B-4,B-5 : 标示方式与公制相同.C: 英制螺丝:C-1: Thread Code:标示皆将分母为8, 再直接称分子之番号.Ex: 1/8 x 0.50 –PPB: 1 分牙螺丝x 0.50” 长, PPBEx: 5/16 x 0.50 –PPB = 2.5/8 x 0.50-PPB : 2 分半牙螺丝x 0.50” 长, PPBEx: 5/32 x 0.50 –PPB =1.25/8 x 0.50-PPB: 1 分2 厘半螺丝x 0.50” 长, PPBEx: 1/4 x 0.50-PPB= 2/8 x 0.50-PPB: 2 分牙螺丝x 0.50” 长, PPB注: 有时会标示粗牙或细牙.UNF: 细牙:电子业较常用.UNC:粗牙: 重机械结构较常用.Ex: 3/8 x 0.50 ,UNF –PPB: 3 分细牙螺丝x 0.50” 长, PPB.C-2: Length Code:为英吋标示, 须乘以25.40 换算为mm螺纹知识本帖被huanping98 执行锁定操作(2007-11-07)7/8"-20 UNF-2B和1/2"-20 UNF-2B中的7/8和1/2表示美国统一螺纹的公称直径；20表示每英寸的牙数；UNF表示美国统一螺纹UN（外螺纹牙底半径任选）系列中的细牙螺纹；2B中的表示螺母螺纹的精度等级。

五金类英语词汇inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模feature die公母模female die母模upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板stripping plate内外打outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mm w=3.2mm L=3~5mm welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5t T=2.5~3.5mm diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mm Runner less无浇道long nozzle延长喷嘴方式模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁?arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手。