汉英分类词汇
航空发动机类型
Aero-Engine Models
超高涵比发动机ultra high bypass engine
超音速冲压喷气发动机scramjet engine
冲压喷气发动机ram-jet engine
带推力转向系统的发动机engine with thrust deflector system
带自由涡轮双轴涡轮轴喷气发动机twin-spool turbo-shaft with free-power turbine
单轴涡轮喷气发动机single-spool turbo-jet engine
低涵比发动机low bypass turbofan
反向旋转发动机contra-rotation engine
高涵比发动机high bypass turbofan
后风扇涡轮喷气发动机aft fan turbo-jet engine 活塞式发动机piston(-and-cylinder) engine // piston-driven engine
桨扇发动机prop-fan engine
离心涡轮喷气发动机centrifugal turbo-jet engine 脉冲喷气发动机pulse jet engine
前风扇涡轮喷气发动机front fan turbo-jet engine 燃气轮机gas turbine engine
三轴桨扇发动机three-shaft prop-fan engine
三轴涡轮前风扇涡轮发动机triple-spool front fan turbo-jet
双轴外涵涡轮喷气发动机twin-spool by-pass turbo-jet
双轴涡轮风扇发动机twin-spool turbo-fan engine 同向旋转发动机co-rotation engine
外骨架发动机exo-skeletal engine
涡轮冲压喷气发动机turbo/ram jet engine
涡轮风扇发动机turbofan engine
涡轮火箭发动机turbo-rocket engine
涡轮螺旋桨发动机turboprop engine
涡轮喷气发动机turbojet engine
涡轮轴发动机turbo-shaft engine
轴流涡轮喷气发动机axial flow turbo-jet engine 型面profile
型面座标图aerofoil ordinate chart
型式form
轴流式压气机axial (flow) compressor
函道duct
函道比by-pass
函道风扇ducted-fan
中介机匣intermediate case
燕尾形样dovetail root
叶片vane(一般指静子叶片)
压气机compressor
压气机机匣compressor case
效率efficiency
压气机盘compressor disc
压缩比compression ratio
牙底root
涡轮导向器turbine nozzle
涡轮盘turbine disc
燃烧室burner // combustion chamber //
combustor
燃烧室外套combustion outer case
燃油导管discharge nozzle
燃油滤fuel filter
燃油喷咀fuel atomizer // fuel spray nozzle
燃油消耗量fuel consumption
火焰筒liner
扩散器机匣diffuse case
加力燃烧室afterburner
航空发动机叶片术语
Terms of Aero-Engine Airfoils
叶片类型
Type of Airfoils
动叶blade // bucket
静叶vane
空心叶片hollow blade // core blade
实心叶片solid blade
涡轮导向器turbine nozzles
涡轮导向器扇形段turbine nozzle segment
涡轮导向器叶片turbine nozzle vane // nozzle
guide vane (ngv)
涡轮工作叶片turbine blade // bucket
涡轮静子叶片turbine nozzle vane // nozzle guide
vane (ngv)
涡轮叶轮turbine wheel
涡轮叶片turbine blades & vanes // buckets
涡轮转子叶片turbine blade // bucket
压气机定子叶片compressor vane // vane
压气机工作叶片compressor blade // blade
压气机叶轮compressor impeller // compressor
wheel
压气机叶片compressor blades & vanes
压气机整流叶片compressor vane // vane
压气机转子叶片compressor blade // blade
叶片的结构特点
Characteristics of Airfoil Structure
283
基体部分base
榫头tip // cog // fir-tree // root // tenon
叶根blade root // root // vane tang
叶冠shroud // tip platform // tip shroud
叶身blade body
叶型部分aerofoil // profile
缘板platform // shroud
叶片的主要名称
Key Terms of Airfoil Body
基体base
进气边/前缘leading edge
理论叶型theoretical developed airfoil/profile
排气边/后缘trailing edge // exhaust edge
弦chord
型线airfoil curve
叶背blade back // convex side // blade convex
叶盆blade basin // vane basin // blade/vane concave
叶片阻尼台blade damper // clapper // mid-span 叶身blade body
叶型公差airfoil tolerance
叶型理论airfoil theory
叶型剖面airfoil section
中弧线airfoil mean line
工装
Tooling
标准件master piece // standard part // tool master 标准块master block // reference block
测具gauge // measuring fixture // measuring tool 测头feeler // gauge head measuring head // stylus 车床夹具lathe fixture
车刀lathe tool// cutter// turning tool
吊具lifting tool
夹具fixture
饺孔夹具reaming fixture // reaming jig
孔位置度测具hole true position gauge
拉刀broach (Bro.) // broaching cutter
拉削夹具broaching fixture
刨削夹具planner fixture
钳工工具bench-work tool
丝套insert // thread insert
丝锥taper // (screwing)tap
镗刀boring cutter
镗杆boring bar (B/bar) // boring spindle
镗孔夹具boring fixture // boring jig
铣槽工具grooving tool
铣床夹具milling jig
铣床铣槽刀milling machine // miller
铣铣槽刀刀milling cutter // milling tool
铣削夹具milling fixture
钻铰刀drill reamer
钻铰复合刀具combined drill and reamer
钻具jig
钻孔铰孔夹具drilling and tapping fixture
钻孔样板drill template (DRT)// drilling
template
钻模(drill) jig
钻模板drill plate (DRP)
钻模与夹具jigs and fixtures
钻套jig bush
钻套jig bush(ing)
钻头bit // drill // drilling bit
机械加工术语
Terms for Machining
半精加工semi-finishing // semifinishing
machining
插slotting
车turning
车床lathe// turning machine
车床研磨lathe lapping
车端面facing
车螺纹thread turning
车螺纹/螺纹加工thread/threading
车削turning
车削螺纹cut thread
成形法forming
冲头blanking ram // piercer // punch // ram head //
slider
冲压(punch) pressing
冲压加工stamping
冲压件pressing //stamping
穿孔/套孔trepan/trepanning
粗加工roughing machining
锉file
倒角deburr // chamfer
倒角/去毛刺deburr(ing)
倒棱chamfer
电解抛光electrochemical polishing // electrolytic
polishing // electro-polishing
电解蚀刻与抛光electrolytic etching and
polishing
调整法machining on preset machine tool
定位locating // location
对刀to size // tool setting
仿形法copying
夹紧clamping
饺reaming
饺孔reaming
饺孔机reaming machine
饺孔钻reamer drill
饺铆钉孔ream a rivet hole
284
精加工finishing // finish machining
锯sawing
锯背back of the saw
锯槽kerf
锯齿serration
锯齿铣sawtooth milling
拉削broaching
冷装shrinkage fitting
铆rivet(ing)
铆钉rivet
磨床grind // grinding machine
磨端面face grinding
磨料abraser // abrasive material // grinding compound
磨削加工abrasive machining
抛polish
抛光buffing // burning // polish (Pol.)
刨planing// shapering
刨槽fillister // slot shaping
刨齿gear shaper cutting // gear-shaping
刨床planer // planing machine// shaper
刨削shaping
去毛刺deburring // fin cutting
镗boring
镗车两用机床boring lathe
镗床borer // boring machine
镗孔boring // borizing (金刚石)
镗磨联合机床combined boring and honing machine
镗钻两用机床boring and drilling machine
铣mill // milling
铣槽slot milling
铣镗床milling-borer // milling and boring machine
铣钻联合机床combined drill and mill machine
铣钻两用机床milling and drilling machine
旋spin
旋锻spin forging // rotary forging // rotary swaging
旋锻机spin forging machine // rotary forging machine // rotary swaging machine
旋压spinning
旋压成型stretch planishing // spin forming
压装press fitting
研lapping
研齿gear lapping
研磨lapping
找正aligning // to center align
装夹set-up
装配assembly
钻drill(ing)
钻床drilling machine
钻孔drilling
钻埋头孔countersink
表面处理
(镀层、涂漆和金属喷镀)
Surface treatment
(Plating,Paining & Metal sparying)
涂层不良imperfectly coated spots
涂层过厚thickening
涂层凸起lifting of the coating, protrusion, or
lifting
冲压
Punch
尺寸检验dimension inspecting
基准datum
技术条件technical condition
加工fabricate
夹clamping
夹紧面clamping surface
夹具fixture
钻孔drill
钻头drill
图纸及工艺规程常用词汇Everyday
Vocabularies on Working Drawings &
W.P.S
尺scale
尺寸dimension // size
尺寸单向极限single of size
尺寸过大oversize
尺寸过小undersize
尺寸极限limit of size
尺寸最大极限maximum of size
尺寸最大余量极限maximum metal of size
尺寸最小极限minimum of size
齿根root
处理treatment
吹砂blast // abrasive blasting
垂直度perpendicularity // squareness
垂直度公差squareness tolerance
单位燃油消耗量specific fuel consumption
单位压力unit pressure
单位装配件assembly unit
单向公差unilateral tolerance
单向公差域bilateral tolerance zone
氮化nitriding
当量equivalent
挡块stop
285
刀柄holder
刀杆cutter bar
刀痕scar // tool mark
等离子喷镀plasma spray
等值equivalent
低压压气机LP compressor
地面试车ground run
典型加工typical operation
防锈rust protection // rust proof
仿形copy
仿形铣床copying milling machine // duplicator 仿型加工form machine
高速钢high speed steel
高速工具钢high speed tool steel
高温合金high temperature alloy
高压压气机HP compressor
根root
根切undercut
公差tolerance
公差带tolerance band
公称尺寸nominal size
功能function
功能尺寸function dimension
功能要求functional requirement
构造尺寸constructional dimension
固定fasten
固定工具fastening tool
故障defect // blemish // failure // fault // imperfection // trouble
故障分析trouble shooting
关键零件critical part
观点view
过盈interference
过盈配合interference fit
过载overload
互换性interchangeability
互换性组件interchangeable assembly
花键splined shaft
花键轴splined shaft
火裂fire cracks
机床machine (tool)
机匣case // casing
基本尺寸base dimension // basic size
基本公差basic tolerance
基本数basic member
基本锥体basic taper
基孔制hole basis limit system
基线basic line
基轴制shaft basis
基轴制shaft basis limit system
基准data // reference
基准尺寸datum dimension
基准点datum point
基准件basic member
基准角basic angle
基准面datum face // datum plane
基准线datum line // zero line
基准叶片master vane
几何公差geometrical tolerance
几何精度accuracy geometrical
加工制造fabricate
夹紧fastening
夹具clamping apparatus // dogging tool // fixture
// holding device // jig
检验装置checker
节径pitch diameter
精度accuracy // precision
精锻precision forging
精加工finishing
精磨precision ground
精确长度exact length
精调fine adjustment // accurate adjustment
//precision adjustment
孔bore // hole
框flame
拉床broacher // broaching machine
拉刀broacher
拉销broach
离心式压气机centrifugal compressor
离心铸造centrispum casting iron
立式车床vertical lathe
立式钻床upright drill
螺母nut
螺栓bolt
名义尺寸base size // nominal size
内径inner diameter
内裂internal crack
内外函发动机by-pass engine
内应力internal stress
内圆磨床internal grinding machine
耐磨性resistance to wear
耐热钢heat resisting steel
耐热合金heat-resisting
啮合mesh
啮合线action line
扭转twisting
排气边trailing edge
排气喷口exhaust nozzle
盘disc
抛光polishing
抛光机polisher // burnishing wheel
刨平plane
泡疤blister
配合fit // matching // mating
286
配合等级classes of fit // grade of fit
配合间隙class of fit
配合类型types of fit
配合容差fitting allowance
配合直径snap diameter
配合制system of fits
配件mating piece
喷口nozzle
喷丸peening // shot-blasting
喷丸处理shot peening
喷雾器atomizer
喷嘴nozzle
批生产mass production
疲劳断裂fatigue fracture
匹配matching
片sheet
偏心的eccentric
偏心距eccentric distance
偏心轮eccentric
偏心套eccentric bushing
偏心轴eccentric axis
偏心装置eccentric
偏移deviation
漆paint
切断parting
切面cutting
切切削深度depth of cut
切头cropping
切削cut
切削工具cutter
切削加工machining
轻合金light alloy
轻微的slight
清楚的clear
清理cleaning
清漆层不好poorly varnished film
区域zone
曲度curve
曲面curved surface
曲线curve
屈服yield
屈服点yield point
屈服强度yield strength
屈服应力proof stress // yield stress
缺口敏感性notch sensitivity
缺陷blemish // defect // failure // fault // imperfection
热脆性red shortness
热裂hot crack
热裂纹clink
热损heat waste
容差allowance
熔化smelt (ing)
蠕变creep
设计design
设计草图rough plan
设计尺寸design size
设计角design angle
伸长elongation
伸长率elongation
失速stall(飞机)
湿吹砂vapour blast
时间表schedule
时效ag(e)ing
时效处理seasoning
识别号identification number
实际尺寸actual size
实际有效直径virtual effective diameter
式样form // manner
事故accident // failure
视图view
试车test run // trial run
试件test piece
试验examine // test
试验参数test data
试样coupon // (test) sample // test specimen
试样长度sample
释放release
手册manual
手段means
寿命limit of life
数number
数据data
数量quantity
说明书description // specification
榫头root
调正adjustment
调质improvement
跳动量runout
凸起overfill
凸台boss
凸缘collar // flange
图scheme
图板drawing board
图号drawing number
图形机体feature
图样draft // drawing
图纸drawing (sheet)
图纸比例drawing scale
图纸技术要求drawing call-out
涂层不良imperfectly coated spots
涂层过厚thickening
涂层凸起lifting of the coating, protrusion, or lifting
287
涂漆paint
推荐尺寸preferred size
推力thrust
推力比thrust ratio
椭圆度ovality
外部检查visual inspection
外函道by-pass duct
外螺纹external screw thread
外形outline
外圆磨床circular grinding machine
位置location
位置公差positional tolerance
蜗杆worm
蜗轮work wheel
卧式钻镗床horizontal boring & drilling machine 误差error
习惯表示法conventional representation
铣床milling machine
铣刀milling
现场site // spot
相当的equivalent
相应值equivalent
消除应力stress relieved // stress released
消耗consumption
销钉pin
销孔bore // pin hole
销子pin
斜度angularity (tolerance)
压板clamp (plate)
氩弧焊argon-arc welding
应变strain
应变时效strain ageing
应力stress
应力腐蚀裂纹stress corrosion crack
应力消除stress relieving
应力-应变曲线stress strain curve
应力-应变图stress strain diagram
圆度circularity // roundness
圆滑smoothness
圆心center of circle
圆柱度cylindricity
直径diameter
制度system
制造manufacture
质量quality
质量验收标准quality acceptance standard
中心距center distance
中心孔center hole
轴shaft
轴承bearing
轴线axis
轴线axis
主喷咀main nozzle
铸造casting
铸造组织casting iron structure
专门技术know-how
专门铣床planomilling machine
专用工具special tool
专用工装special tooling
专用设备special purpose machine
专用铣床production machine
转换reset
转子叶片blade
装备device
装夹mount
装配assembly // mount
装配车间assembling shop // assembly shop //
erecting shop // fitting shop
装配间隙fit clearance
装配件assembly
装配图assembly drawing // erection drawing
装箱退火close annealing
装置device
锥齿轮bevel gear
锥度taper
锥螺纹taper thread
锥面conical surface
锥体slow object // taper
总尺寸外形尺寸overall dimension
总体布置图general layout
总装车间assembly department
总装件assembly // general assembly
总装图general layout
组合件joint
组件assembly
组装件sub assembly
钻drill
钻床drill machine
钻具jig
钻孔drill
钻套drill jig bush
钻头号drill number
最大长度max length
最大间隙major clearance
最大推力full thrust // top thrust
最大直径major diameter
最小长度min length
最小间隙minor clearance
最小直径minor diameter
缺陷解释
Interpretation of Defects
凹陷undercutting (在母材上沿焊接边的沟槽或
288
充填不足)
变形deformation (在加工时未能保持住形状不变或与相邻部有不顺滑转接)
电解腐蚀electrolytic action(不同金属间的电蚀作用造成的缺陷)
断裂fracture(受力过大造成的破坏)
开裂flaw
外贸常用词语和术语Everyday Vocabularies of Foreign Trade
询盘
Inquiry
把某物交付给某人to deliver sth to sb
把询价记录在卷to keep the inquiry on file
办理交货to effect delivery // to make delivery
还盘
Counter Offer
还盘counter offer
享有盛誉enjoy great popularity
与某人达成交易conclude business with sb.
达成交易close business // close a deal // close a
transaction // close a bargain
价格
Price
成本加保险费运费价cost, insurance & freight
(C.I.F.)
成本加运费价cost & freight (CFR)
船上交货free on board (F.O.B)
底价floor price
货币currency
价格偏低on the low side
价格条件price terms
廉价出售 a bargain sale
市场价market price
讨价还价bargain
为某事拼命讨价还价drive a hard bargain over
sth.
与某人成交make a bargain with sb
最低价rock-bottom price
289
290
英汉无损检测专业词汇汇编 夏纪真编 A ablution 清洗Absorbed dose 吸收剂量 Absorbed dose rate 吸收剂量率 A.C magnetic saturation 交流磁饱和acceptance specification 验收规范Acceptanc limits 验收范围 Acceptance level 验收水平验收标准Acceptance standard 验收标准Accessories 附件配件辅助设备辅助器材Accumulation test 累积检测 Accuracy 精确度准确度acetone 丙酮 Acoustic emission count 声发射计数Acoustic emission transducer 声发射换能器Acoustic emission (AE) 声发射Acoustic holography 声全息术 Acoustic impedance 声阻抗Acoustic impedance matching 声阻抗匹配Acoustic impedance method 声阻法Acoustic wave 声波 Acoustic-ultrasonic 声-超声(AU)Acoustical lens 声透镜 across 交* 横过 Activation 活化Activity 活度 Adequate shielding 适当防护、适当屏蔽 address: 地址: additional stress 附加应力 AE 声发射air header 集气管 air set 空气中凝固, 常温自硬自然硬化air supply 气源 aisle 过道走廊alkaline battery 碱性电池 alarm level 报警电平alarm condition 报警状态 Alignment 对准定位调整校直allowable variation 允许偏差容许变化alternating current 交流电aluminum powder 铝粉 amount 数量Ampere turns 安匝数 amplifier panel 放大器面板Amplitude 振幅、幅度 anchor bolt 锚定螺栓地脚螺栓 analyzer 分析器Angle beam method 斜射法、角波束法Angle beam probe 斜探头、角探头Angle of incidence 入射角 Angle of reflection 反射角Angle of spread 扩散角 Angle of squint 偏向角、偏斜角Angle probe 斜探头、角探头
Size 尺寸 Page 页数 Paper (Cover/text) 纸质(封面纸/内页纸) Binding 装订 Quantity 数量 Dust jacket护封 End paper 环衬 关于尺寸: Portrait 纵长型(纵开本) Landscape 横长型(横开本) 关于页数: Page 页 Sheet 张 1 sheet = 2 pages 关于纸质: Glossy/gloss 有光泽的 Matt/matte 哑面的 Art /coated/art/glossy coated paper 铜版纸 Matt/matte art paper 哑面纸/哑粉纸 Wood free paper 道林纸(不含木浆的纸) Offset paper 双胶纸/书纸 关于光油/光胶(光膜): (Through/spot)Varnish/coating (整版/局部)光油 UV/Glossy/matt Varnish/coating Matt/glossy laminated 过哑胶(哑膜)/过光胶(光膜) Blocking/die-stamping/gold embossing/gold pressing/gold stamping 烫金Embossing/die stamping 凹凸印刷 印刷 印油Transparent ink 印光油Gloss Varnishing 印哑油Matt Varnishing 印专色Printed in spot color 表面处理 磨光Calendering 磨光吸塑油Blister-calendering varnish 过光油Varnishing 过水油Aqueous coating
工程材料常用词汇表 A 奥氏体 austenite 奥氏体本质晶粒度 austenite inhorent grain size 奥氏体化 austenitization, austenitii zing B 白口铸铁 white cast iron 白铜 white brass, copper-nickel alloy 板条马氏体 lath martensite 棒材 bar 包晶反应 peritectic reaction 薄板 thin sheet 薄膜技术 thin film technique 贝氏体 bainite 本质晶粒度 inherent grain size 比强度 strength-to-weight ratic 变质处理 inoculation, modification 变质剂 modifying agent,modificator 表面处理 surface treatment 表面粗糙度 surface roughness 表面淬火 surface quenching 表面腐蚀 surface corrosion 表面硬化 surface hardening 玻璃 glass 玻璃态 vitreous state, glass state 玻璃钢 glass fiber reinforced plastics 玻璃纤维 glass fiber 不可热处理的 non-heat-treatable 不锈钢 stainless steel 布氏硬度 Brinell hardness C 材料强度 strength ofmaterial 残余奥氏体residual austenite 残余变形 residual deformation 残余应力 residual stress 层状珠光体 lamellar pearlite
数学常用词汇中英文对照 代数部分 1、有关基本运算: add,plus加 subtract减 difference差 multiply,times乘 product积 divide除 divisible可被整除的dividedevenly被整除 dividend被除数 divisor因子,除数 quotient商 remainder余数 factorial阶乘 power乘方 radicalsign,rootsign根号 roundto四舍五入 tothenearest四舍五入 2.有关集合 union并集 proper subset真子集 solution set解集 3.有关代数式、方程和不等式algebraic term代数项 like terms,similar terms同类项numerical coefficient数字系数literal coefficient字母系数inequality不等式 triangle inequality三角不等式range值域 original equation原方程equivalent equation同解方程 等价方程 linear equation线性方程 4.有关分数和小数 proper fraction真分数 improper fraction假分数mixed number带分数 vulgar fraction,common fraction普通分数simple fraction简分数 complex fraction繁分数 numerator分子 denominator分母 (least)common denominator(最小)公分母quarter四分之一 decimal fraction纯小数 infinite decimal无穷小数 recurring decimal循环小数 tenthsunit十分位 5.基本数学概念 arithmetic mean算术平均值 weighted average加权平均值 geometric mean几何平均数 exponent指数,幂 base乘幂的底数,底边 cube立方数,立方体 square root平方根 cube root立方根 common logarithm常用对数 digit数字 constant常数 variable变量 inversefunction反函数 complementary function余函数 linear一次的,线性的 factorization因式分解 absolute value绝对值, round off四舍五入 6.有关数论 natural number自然数 positive number正数 negative number负数 odd integer,odd number奇数 even integer,even number偶数 integer,whole number整数 positive whole number正整数 negative whole number负整数consecutive number连续整数 rea lnumber,rational number实数,有理数
电机英语词汇汇总 发电机通常由定子、转子、端盖及轴承等部件构成。 定子由定子铁芯、线包绕组、机座以及固定这些部分的其他结构件组成。 转子由转子铁芯(或磁极、磁扼)绕组、护环、中心环、滑环、风扇及转轴等部件组成。 由轴承及端盖将发电机的定子,转子连接组装起来,使转子能在定子中旋转,做切割磁力线的运动, 从而产生感应电势,通过接线端子引出,接在回路中,便产生了电流。 Belt pulley 皮带轮 stator 定子 rotor 转子 rotor core 转子铁芯 stator core 定子铁芯 induction motor 感应电动机 winding 绕组 solt 槽 cast-aluminum rotor 铸铝转子 insulation 绝缘 ac motor 交流环电动机 alloy 合金 frequency 频率 revolutions per minute 转/分 motoring 电动机驱动 generating 发电 no-load 空载 full load 满载 staor winding 定子绕组 full-load torque 满载转矩 shunt 并励 series 串励 modulator 调制器 overhauling 检修 Polyphase 多相(的) polyphase rectifier 多相整流器 shunt 分路器 regulator 调节器 rotor (stator) winding 转子(定子绕组) rheostat 变阻器 subcompact 微型汽车 armature coil 电枢线圈 rotating commutator 旋转(整流子)换向器 commutator-brush combination 换向器-电刷总线 mechanical rectifier 机械式整流器
同济大学外国语学院博士点简介 辉煌同济,百年外语。1907年同济德文医学堂初创之时即设德文科,同济德语教学可谓中国德语教学之缩影。同济外语教学历经百年风雨,名家荟萃,人才辈出,形成了深厚的文化积淀,许多著名外语学者在同济外语百年时光隧道中流连。如诗人、翻译家冯至,作家、哲学家陈铨,诗人殷夫,日耳曼学者张威廉,德语学者廖馥君、邱震海等均在此或求学或任教,为同济外语发展做出了卓越贡献。 改革开放之初,同济大学外语系已开始招生研究生,迄今为止,外语专业硕士研究生教育已有30余年历史,1982年获德语硕士授予权。现已有德语语言文学、英语语言文学、日语语言文学、外国语言学及应用语言学二级学科硕士授权点4个,外语语言文学一级硕士授权点1个,外国语言学及应用语言学博士授权点1个,形成健全的外语学科体系。 本学科英语语言学主要涉及理论语言学与应用语言学,研究方向有生成音系学、实验语音学、生成句法学、语用学、语义学、多模态语言研究、功能语言学、外语教学理论与实践、翻译美学、翻译学和英美文学等领域,本学科点特色在于形式语言学研究与功能语言学研究并举,这在国内高校中是极为罕见的。其中,音系学研究、功能语言学研究、多模态语言研究居于国内领先地位。 德语语言学方向主要集中在德语词汇学和二语习得研究两方面。德语词汇学以德语词汇研究为核心,涵盖德语形态学、构词学,科技德语术语学、语义学、认知语言学等有关语言理论,并由此扩展到德汉语言比较,中德跨文化交际等方面。二语习得研究包括从传统语法翻译法到交际法、功能交际理论等各种德语教学法研究,尤其是开展对外德语教学在中国的研究,同时开展教育心理学、跨文化交际等理论研究, 具体研究对象可扩展到大纲、教材、测试、教学手段、教学模式和教学方法等方面。 日语语言学方向在全面了解语言学在日本的传播及发展、进一步深化日语语法、词汇以及表达研究的基础上,更加侧重在日语中体现得较为明显的语用学和认知语言学的研究,以进一步弄清日语中的复杂的言外之意的表达和对事物的独特的认知方式以及由此带来的独特表达方式,并进一步通过语言理解日本文化,以及研究独特的日本文化对语言表达产生的影响。通过日语与汉语的比较研究,深化和完善现有的翻译理论,并进一步对语料库进行探讨、研究,弄清语料库在日汉语语法、词汇比较研究及中日-日中翻译研究中的作用、功能和局限,为完善现有的语料库提供支持。 本博士点以国家社科基金项目、教育部人文社科项目及多项市级、校级科研项目为依托,逐步形成具有鲜明学科特色的科研平台,科研队伍稳定,研究成果颇丰。 本博士点现有博士生导师9人,已招收培养博士研究生12人。 即:研究方向: 1.英语语言学(形式语言学、功能语言学、英汉对比、翻译学、外语教学理论及应用、英美文学) 2.德语语言学(含德语专用语研究、德语词汇学、二语习得研究、德国研究与德国文化学) 3.日语语言学(含认知语言学,语用学,翻译理论研究) 外国语言学及应用语言学(050211 )导师队伍
土木工程专业外语词汇大全中英翻译 1. 综合类 大地工程geotechnical engineering 反分析法back analysis method 基础工程foundation engineering 临界状态土力学critical state soil mechanics 数值岩土力学numerical geomechanics 土soil, earth 土动力学soil dynamics 土力学soil mechanics 岩土工程geotechnical engineering 应力路径stress path 应力路径法stress path method 2. 工程地质及勘察 变质岩metamorphic rock 标准冻深standard frost penetration 冰川沉积glacial deposit 冰积层(台)glacial deposit 残积土eluvial soil, residual soil 层理beding 长石feldspar 沉积岩sedimentary rock 承压水confined water 次生矿物secondary mineral 地质年代geological age 地质图geological map 地下水groundwater 断层fault 断裂构造fracture structure 工程地质勘察engineering geological exploration 海积层(台)marine deposit 海相沉积marine deposit 花岗岩granite 滑坡landslide 化石fossil 化学沉积岩chemical sedimentary rock 阶地terrace 节理joint 解理cleavage 喀斯特karst 矿物硬度hardness of minerals 砾岩conglomerate
一、代数部分 (Algebra) 1. 数学运算 equal, is equal to 等于equivalent to 等价于 is greater than 大于 is lesser than 小于 is equal or greater than 大于等于is equal or lesser than 小于等于operator 运算符 add, plus 加 subtract 减 difference 差 multiply, times 乘 product 积 divide 除 augend, summand 被加数addend 加数 minuend 被减数 subtrahend 减数 remainder 差 multiplicand, faciend 被乘数multiplicator 乘数 product 积 dividend 被除数 divisor 除数 quotient 商 remainder 余数 divisible 可被整除的 divided evenly 被整除divisor 因子,除数 dividend 被除数 factorial 阶乘 power 乘方 radical sign, root sign 根号 factorial 阶乘 logarithm 对数 exponent 指数,幂 power 乘方 square 二次方,平方 cube 三次方,立方 the power of n, the nth power n 次方 evolution, extraction 开方 square root 二次方根,平方根 cube root 三次方根,立方根 the root of n, the nth root n次方 根 2. 数字 digit数字 number数 natural number 自然数 integer/whole number 整数 positive number 正数 negative number 负数 positive whole number 正整数 negative whole number 负整数 consecutive number 连续整数 odd integer, odd number 奇数 even integer, even number 偶数 real number 实数 rational number 有理数 irrational number 无理数 consecutive 连续数 inverse / reciprocal 倒数 composite number 合数 prime number 质数 common divisor 公约数 multiple 倍数 (least) common multiple (最小)公 倍数 (prime) factor (质)因子 common factor 公因子 nonnegative 非负的 units 个位 tens 十位 ordinary / decimal scale 十进制 binary system 二进制 hexadecimal system 十六进制 weight, significance 权 carry 进位 truncation 截尾 round to / to the nearest 四舍五 入 round down 下舍入 round up 上舍入 significant digit 有效数字 insignificant digit 无效数字 3. 分数和小数 decimal 小数 decimal point 小数点 fraction 分数 numerator 分子 denominator 分母 proper fraction 真分数 improper fraction 假分数 common fraction 普通分数 mixed number 带分数 simple fraction 简分数 complex fraction 繁分数 (least) common denominator (最 小)公分母 quarter 四分之一 decimal fraction 纯小数 infinite decimal 无穷小数 recurring decimal 循环小数 places位(thousands’ place, hundreds’place,tens’place, units’ place (ones’ digit), tenths’ place,hundredths’ place,thousandths’ place.) 4. 集合与函数 aggregate 集合 element 元素 void 空集 subset 子集 union 并集
电机专业英语词汇全 induction machine 感应式电机 horseshoe magnet 马蹄形磁铁 magnetic field 磁场 eddy current 涡流 right-hand rule 右手定则 left-hand rule 左手定则 slip 转差率 induction motor 感应电动机 rotating magnetic field 旋转磁场 winding 绕组 stator 定子 rotor 转子 induced current 感生电流 time-phase 时间相位 exciting voltage 励磁电压 slot槽 lamination 叠片 laminated core 叠片铁芯 short-circuiting ring 短路环 squirrel cage 鼠笼 rotor core 转子铁芯 cast-aluminum rotor 铸铝转子 bronze 青铜 horsepower 马力 random-wound 散绕 insulation 绝缘 AC motor 交流环电动机 end ring 端环 alloy 合金 coil winding 线圈绕组
form-wound 模绕 performance characteristic 工作特性 frequency 频率 revolutions per minute 转/分 motoring 电动机驱动 generating 发电 per-unit value 标么值 ,,, breakdown torque 极限转矩 breakaway force 起步阻力 overhauling 检修 wind-driven generator 风动发电机 revolutions per second 转/秒 number of poles 极数 speed-torque curve 转速力矩特性曲线 plugging 反向制动 plug插头,塞子,栓 synchronous speed 同步转速 percentage 百分数 locked-rotor torque 锁定转子转矩 full-load torque 满载转矩 prime mover 原动机 inrush current 涌流 magnetizing reactance 磁化电抗 line-to-neutral 线与中性点间的 stator winding 定子绕组 leakage reactance 漏磁电抗 no-load 空载 ,,, full load 满载 Polyphase 多相(的) iron-loss 铁损 complex impedance 复数阻抗 rotor resistance 转子电阻 leakage flux 漏磁通 locked-rotor 锁定转子
A Type Wooden Ladder A字木梯 A-frame A型骨架 A-truss A型构架 Abandon 废弃 Abandoned well 废井 Aberration of needle 磁针偏差Abnormal pressure 异常压力abnormally high pressure 异常高压Abort 中止 abrasion 磨损 Abrasion surface 浪蚀面 abrasive cut-off machine 磨切机Abrasive Cutting Wheel 拮碟abrasive grinding machine 研磨机Abrasive Grinding Wheel 磨碟abrasive particle 磨料颗粒 Absolute address 绝对地址Absolute altitude 绝对高度Absolute damping 绝对阻尼Absolute deviation 绝对偏差Absolute flying height 绝对航高Absolute gravity 绝对重力 absolute permeability 绝对渗透率absolute porosity 绝对孔隙率absolute temperature 绝对温度absorbability 吸收性;吸附性absorption 吸收 abutment 桥墩 abutting end 邻接端 acceleration 加速 acceleration lane 加速车道Acceleration of gravity 重力加速度acceleration pedal 加速器踏板accelerator 催凝剂;加速器;催化剂acceptance criteria 接受准则 access 通路;通道 access door 检修门;通道门access lane 进出路径 access panel 检修门 access point 入口处;出入通道处access ramp 入口坡道;斜通道access road 通路;通道 access shaft 竖井通道 access spiral loop 螺旋式回旋通道access staircase 通道楼梯 access step 出入口踏步 access tunnel 隧道通道 accessible roof 可到达的屋顶accessory 附件;配件accident 事故;意外 accidental collapse 意外坍塌 accommodate 装设;容纳 accredited private laboratory 认可的私 人实验室 accumulator 储压器;蓄电池 accuracy limit 精度限制 acetylene cylinder 乙炔圆筒 Acetylene Hose 煤喉 Acetylene Regulator 煤表 acid plant 酸洗设备;酸洗机 acid pump 酸液泵 acid tank 酸液缸 acidic rock 酸性岩 acoustic couplant 声耦合剂 acoustic coupler 声音藕合器;音效藕 合器 acoustic lining 隔音板 acoustic screen 隔声屏 Acoustic wave 声波 acrylic paint 丙烯漆料(压克力的油漆) acrylic sheet 丙烯胶片(压克力的胶片) active corrosion 活性腐蚀 active earth pressure 主动土压力 active fault 活断层 active oxidation 活性氧化 actual plot ratio 实际地积比率 actuator 促动器;唧筒;激发器 adapt 改装 adaptor 适配器;承接器;转接器; addition 增设;加建 additional building works 增补建筑工 程 additional horizontal force 额外横向力 additional plan 增补图则(附加的平面 图) additional vent 加设通风口 additive 添加剂 Address 地址 adhesive 黏结剂;胶黏剂 adhesive force 附着力 Adhesive Glue 万能胶 Adhesive Reflective Warning Tape 反 光警告贴纸 adit 入口;通路;坑道口 adjacent construction 相邻建造物 adjacent level 相邻水平 adjacent site 相邻基地 adjacent street 相邻街道 adjoining area 毗邻地区 adjoining building 毗邻建筑物 adjoining land 毗邻土地 adjoining structure 毗邻构筑物 adjustable 可调校 Adjustable Wrench Spanner 昔士 adjuster 调节器 adjustment 调校;调整 Administrative Lawsuit 行政诉讼 Administrative Remedy 行政救济 admixture 掺合剂;外加剂 advance directional sign 前置指路标 志;方向预告标志 advance earthworks 前期土方工程 advance warning sign 前置警告标志 advance works 前期工程 aeration 曝气 aeration tank 曝气池 aerial 天线 Aerial mapping 航空测图 aerial photograph 航测照片 Aerial photography 航照定位 aerial rapid transit system 高架快速运 输系统 aerial ropeway 高架缆车系统 aerial view 鸟瞰图 aerofoil 翼型 aerosol 悬浮微粒;喷雾 aerosphere 大气圈 affix 贴附 aftercooler 后冷却器 afterfilter 后过滤器 aftershock 余震 agent 作用剂;代理人 aggradation 堆积 aggregate 骨材;集料;碎石 aggregate area 总面积 aggregate grading 骨材级配 aggregate superficial area 表面总面积 aggregate usable floor space 总楼地板 空间 agitator 搅拌器;搅动机 air bleeding 放气(空气渗出) air blower 鼓风机 air brake 气压制动器 Air chambor 气室 air circuit 空气回路 air circuit breaker 空气断路器 air cleaner 空气滤清器
数学mathematics 公理axiom 定理theorem 计算calculation 运算operation 证明prove 假设hypothesis, hypotheses(pl.) 命题proposition 算术arithmetic 加plus(prep.), add(v.), addition(n.) 被加数augend, summand 加数addend 和sum 减minus(prep.), subtract(v.), subtraction(n.) 被减数minuend 减数subtrahend 差remainder 乘times(prep.), multiply(v.), multiplication(n.) 被乘数multiplicand, faciend 乘数multiplicator 积product 除divided by(prep.), divide(v.), division(n.) 被除数dividend 除数divisor 商quotient 等于equals, is equal to, is equivalent to 大于is greater than 小于is lesser than 大于等于is equal or greater than 小于等于is equal or lesser than 运算符operator 数字digit 数number 自然数natural number 整数integer 小数decimal 小数点decimal point 分数fraction 分子numerator 分母denominator 比ratio 正positive 负negative 零null, zero, nought, nil 十进制decimal system 二进制binary system 十六进制hexadecimal system 权weight, significance 进位carry 截尾truncation 四舍五入round 下舍入round down 上舍入round up 有效数字significant digit 无效数字insignificant digit 代数algebra
induction machine 感应式电机horseshoe magnet 马蹄形磁铁magnetic field 磁场 eddy current 涡流 right-hand rule 右手定则 left-hand rule 左手定则 slip 转差率 induction motor 感应电动机 rotating magnetic field 旋转磁场winding 绕组 stator 定子 rotor 转子 induced current 感生电流 time-phase 时间相位 exciting voltage 励磁电压 solt 槽 lamination 叠片 laminated core 叠片铁芯 short-circuiting ring 短路环squirrel cage 鼠笼 rotor core 转子铁芯 cast-aluminum rotor 铸铝转子 bronze 青铜 horsepower 马力 random-wound 散绕 insulation 绝缘 ac motor 交流环电动机 end ring 端环 alloy 合金 coil winding 线圈绕组 form-wound 模绕 performance characteristic 工作特性frequency 频率 revolutions per minute 转/分motoring 电动机驱动 generating 发电 per-unit value 标么值 breakdown torque 极限转矩breakaway force 起步阻力overhauling 检修 wind-driven generator 风动发电机revolutions per second 转/秒number of poles 极数 speed-torque curve 转速力矩特性曲线plugging 反向制动 synchronous speed 同步转速percentage 百分数 locked-rotor torque 锁定转子转矩full-load torque 满载转矩 prime mover 原动机 inrush current 涌流 magnetizing reactance 磁化电抗line-to-neutral 线与中性点间的stator winding 定子绕组 leakage reactance 漏磁电抗 no-load 空载 full load 满载 Polyphase 多相(的) iron-loss 铁损 complex impedance 复数阻抗 rotor resistance 转子电阻leakage flux 漏磁通 locked-rotor 锁定转子 chopper circuit 斩波电路separately excited 他励的compounded 复励 dc motor 直流电动机 de machine 直流电机 speed regulation 速度调节 shunt 并励 series 串励 armature circuit 电枢电路 optical fiber 光纤 interoffice 局间的 waveguide 波导波导管 bandwidth 带宽 light emitting diode 发光二极管silica 硅石二氧化硅regeneration 再生, 后反馈放大coaxial 共轴的,同轴的 high-performance 高性能的 carrier 载波 mature 成熟的 Single Side Band(SSB) 单边带coupling capacitor 结合电容propagate 传导传播 modulator 调制器 demodulator 解调器
电气工程师专业英语词汇汇总 10kV distribution substation 10kV配电所abrupt change of voltage 电压突变accumulation of electric energy 电能存储actuating coil 动作线圈adjustment diagram 调整图 alarm 报警 alarm signal 报警信号alternating light 变光灯 ammeter 电流表 apparent energy consumption unit 单位视在能耗 arc furnace 电弧炉 armature 电枢 arrester; lighting arrester; surge diverters 避雷器 automatic voltage regulator 电压自动调整器backlighting; background illumination 背景照明 battery box 电池箱 battery charger 电池充电器battery contactor 电池接触器battery fuse 电池保险丝battery resistor 电池电阻器 blow-out coil 磁吹线圈 boom 吊杆 bracket (OCS) 底座(接触网); 支架;托架bracket for headspan wire 定位索底座bridge 电桥 brush 电刷 built-in wardrobe; built-in closet; closet 壁灯 bulb; light(lamp) bulb; electric bulb 灯泡 butterfly valve with electric actuator 电动蝶阀 button 电钮 cable and accessories 电缆及附件 cable armour 电缆铠装 cable bays 电缆电线间隔cable box 电缆箱 cable bracket; cable tray 电缆托架 cable continuity test 电路复测 cable differential protection 电缆差动保护
Common V ocabulary of Sedimentology 沉积学常用词汇 A abandoned channel 废弃河道 abandoned delta 废弃的三角洲 ablation breccia 消融角砾岩 abrasion terrace 海蚀阶地 absolute age 绝对年龄 absorpting 吸附性 absorption 吸收性 abundance of trace element 微量元素丰度abyss(deep sea) 深海 abyssal basin 深海盆地 abyssal deposit 深海沉积 abyssal facies 深海相 abyssal ooze 深海软泥 abyssal plain 深海平原 abyssal subcompensational basin 深海欠补偿盆地 accretion ripple 加积波痕 accretion topography 加积地形 accretional plain 加积平原 accumulation terrace 堆积阶地 ACD(aragonite compensation depth) 文石补偿深度 acicular texture 针状结构 acid sialic stage 酸性硅铝阶段 active continental margin 活动大陆边缘active crust 活动地壳 adhesion ripple 粘附波痕 adhesion wart 粘附瘤痕 advanced dune 前进沙丘 aeolian dune facies 风成沙丘相 aeolian ripple marks 风成波痕 aeolian rock 风成岩 agglomerate 集块岩agglomeratic texture 集块结构agglutinated grain texture 胶粒结构aggradation 加积作用 air-heave structure 气胀结构aleuropelitic texture 粉沙泥质结构algal mat 藻席 algal mound 藻丘 algal ooid 藻鲕 algal peloid 藻球粒 algal reef 藻礁 algal reef limestone 藻礁灰岩 alkali lake 碱湖 alkali-feldspar 碱性长石 allitized stage 铝铁土阶段 allochem 异化颗粒 allochemical limestone 异化颗粒灰岩allochemical phosphorite 异化磷块岩allochthonous limestone 异地灰岩allochthonous phosphorite 异地磷块岩alluvial apron 冲积裙 alluvial facies 冲积相 alluvial fan 冲积扇 alluvial plain 冲积平原 alluvial terrace 冲积阶地 altered tuff 蚀变凝灰岩 ammonoid 菊石类 amorphous texture 胶状结构amphibian 两栖动物 amygdaloidal structure 杏仁结构anadiagenesis 后生成岩作用analcimolith 方沸石岩 analysis of rocks and minerals 岩矿分析angiosperm 被子植物 angular 棱角状 angular gravel 角砾
1DESIGN BASIS 设计依据 计划建议书planning proposals 设计任务书design order 标准规范standards and codes 条件图information drawing 设计基础资料basic data for design 工艺流程图process flowchart 工程地质资料engineering geological data 原始资料original data 设计进度schedule of design 2STAGE OF DESIGN 设计阶段 方案scheme, draft 草图sketch 会谈纪要summary of discussion 谈判negotiation 可行性研究feasibility study 初步设计preliminary design 基础设计basic design 详细设计detail design 询价图enquiry drawing 施工图working drawing, construction drawing 竣工图as built drawing 3CLIMATE CONDITION 气象条件 日照sunshine 风玫瑰wind rose 主导风向prevailing wind direction 最大(平均)风速maximum (mean) wind velocity 风荷载wind load 最大(平均)降雨量maximum (mean) rainfall 雷击及闪电thunder and lightning 飓风hurricane 台风typhoon 旋风cyclone 降雨强度rainfall intensity 年降雨量annual rainfall 湿球温度wet bulb temperature 干球温度dry bulb temperature 冰冻期frost period