k-power-product-description

Instruction ManualCONTENTS1. PRODUCT DESCRIPTION1-1. Introduction --------------------------------------------------------- ( 3 )1-2. Technical Specifications ---------------------------------------- ( 6 )1-3. Equipment Ratings ----------------------------------------------- ( 8 )1-4. Supplied Accessories -------------------------------------------- ( 9 )1-5. International electrical Symbol -------------------------------- ( 9 )2. INSTALLATION2-1. Initial Inspection --------------------------------------------------- (10)2-2. Connecting AC Power ------------------------------------------- (10)2-3. Cooling and Ventilation ----------------------------------------- (10)2-4. Position -------------------------------------------------------------- (10)2-5. Warming-Up ------------------------------------------------------- (10)3. OPERATION3-1 Voltage Measurement -------------------------------------------- (11)3-2 Current Measurement -------------------------------------------- (11)3-3 Resistance Measurement --------------------------------------- (12)3-4 Diode Measurement ---------------------------------------------- (13)3-5 Continuity Test ----------------------------------------------------- (13)3-6 Frequency Measurement --------------------------------------- (13)4. MAINTENANCE4-1. Fuse Replacement ----------------------------------------------- (14)4-2. Adjustment and Calibration ------------------------------------ (14)4-3. Cleaning and decontamination ------------------------------- (14)1. PRODUCT DESCRIPTION1-1. IntroductionThank you for purchasing our product. Electronic measuring instruments produced by us are high technology products made under strict quality control. We guarantee their exceptional precision and utmost reliability. For proper use of the product, please read this operation manual carefully.Note1. To fully maintain the precision and reliability of the product use it within the rangeof standard setting (Temperature 10 °C~35 °C, Humidity 45%~85%)2. After turning of power, please allow a pre-heating period of as long as some 30minutes before use.3. This equipment should be used with a triple line power cord for safety.4. For quality improvement the exterior design and specification of the product canbe changed without prior notice.5. If you have further questions concerning use, please contact our service centeror sales outlet.This Digital multimeter is a portable, bench type Digital multimeter with a 4 1/2digit light-emitting diode. This Digital multimeter can make diode measurements, Frequency measurements & continuity test, in addition to Current, Voltage and Resistance measurements.Features• Bench type True RMS Digital Multimeter with 4 1/2 digit (LED)display.• Basic accuracy for DCV ; 0.05 %• Overload protection on all range• AC/DC Voltage measurement(Up to DC 1200V, AC 750V)• AC/DC Current measurement(Up to 20A)• Resistance measurement(Up to 20M Ω)• Frequency Measurement(Up to 200KHz)• Audible continuity testFIG.1 FRONT PANELInput TerminalⓑCOM : COMMON TerminalⓒV /Ω /Hz : VOLT/ OHM/CONTINUITY/ FREQUENCY/ DIODE TEST Input Terminal ⓓ mA : mil Ampere Input Terminalⓔ A : Ampere Input TerminalFunction Selection① I/O Power ON/OFF ⑤ AC A AC Current② DC V DC Voltage ⑥ΩResistance③ AC V AC Voltage ⑦ DIODE Diode & Continuity④ DC A DC Current ⑧ FRQ FrequencyRange Selection⑨2 2V, 2mA ,2 KΩ⑬ 20 M 20 MΩ⑩20 20V, 20mA , 20 KΩ, 20 KHz ⑭ 20A 20A⑪200 200V,200mA, 200KΩ, 200KHz ⓐ HOLD Data Hold⑫2000 DC 1200V/AC1000V, 2000mA, 2000 KΩInput Terminal LimitsSwitch FunctionInputTerminalsRed BlackMin. DisplayReadingMax. DisplayReadingMaximumInputDC V VΩHz COM 0.0001V 1200.0V 1200Vdc,AC V VΩHz COM 0.0001V 1000.0V 1000 VacOHM VΩHz COM 0.0001KΩ 19.999MΩ 600V(1Min) Diode/Cont. VΩHz COM 0.1 1999.9 600 V(1Min)DC mA mA COM 0.0001mA 1999.9mA 2 AAC mA mA COM 0.0001mA 1999.9mA 2 ADC A A COM 0.001 A 19.999 A 20.00 AAC A A COM 0.001 A 19.999 A 20.00 A Frequency VΩHz COM 0.001KHz 199.99KHz 600 V(1 Min)FIG.2 REAR PANELAC INLET : AC power input connectorVOLTAGE SELECTOR : Selects the AC Power (115V or 230V)HOLDER : Replace fuse by unscrewing.GROUND TERMINAL1-2 Technical SpecificationImportant Note: All accuracies apply to 5% to 95% full scale of each range- DC VOLTRange Resolution Accuracy Impedance2 V 20 V 200 V 100 uV1 mV10 mV±(0.05% + 5d)1000V 100mV ±(0.1% + 5d) 10 MΩ1200V1200V 100mV ±(0.3% + 5d)- AC VOLTRange Resolution Frequency AccuracyImpedance 2V 100 uV40Hz to 60Hz ±(0.75% + 10d)60Hz to 1KHz ±(1.5% + 10d)1KHz to 5KHz ±(2.5% + 10d) 10 MΩ5KHz to 10KHz ±(5.0% + 10d) 20V 1 mV40Hz to 60Hz ±(0.75% + 10d)60Hz to 1KHz ±(2.5% + 10d)1KHz to 5KHz ±(5.0% + 10d)5KHz to 10KHz ±(10% + 10d) 200V 10 mV40Hz to 50Hz ±(1.0% + 10d)50Hz to 60Hz ±(0.75% + 10d)60Hz to 1KHz ±(2.5% + 10d)1KHz to 5KHz ±(5% + 10d) 750V 100 mV 40Hz to 50Hz ±(1.0% + 10d)50Hz to 60Hz ±(0.75% + 10d)60Hz to 400Hz ±(2.5% + 10d)400Hz to 1KHz ±(5% + 10d)- DC CURRENTRange Resolution Accuracy Over Load Protection2 mA 20 mA 200 mA 100 nA 1 uA 10 uA ±(0.75% + 5d) 2 A 100 uA ±(1.0% + 5d) 2A/250V20 A1 mA±(1.0 % + 10d)15A/250V 20A Range for 15 seconds max during each 15 minute period- AC CURRENTRangeResolution Frequency Accuracy Over LoadProtection2mA 100 nA 40Hz to 50Hz ±(1.5% + 10d) 2A/250V20mA 1 uA 50Hz to 60Hz ±(0.75% + 10d) 200mA10 uA60Hz to 1KHz ±(2.0% + 10d)1KHz to 5KHz ±(3.0% + 10d)2000mA100 uA40Hz to 50Hz ±(1.5% + 10d) 50Hz to 60Hz ±(1.0% + 10d) 60Hz to 1KHz ±(2.0% + 10d)1KHz to 5KHz ±(3.0% + 10d) 20A 1mA40Hz to 50Hz ±(1.5% + 10d)15A/250V 50Hz to 60Hz ±(1.0% + 10d) 60Hz to 1KHz ±(2.0% + 10d)1KHz to 2KHz±(3.0% + 10d)20A Range for 15 seconds max during each 15 minute period- RESISTANCERange Resolution Accuracy Over Load Protection2 KΩ20 KΩ200 KΩ2 MΩ0.1 Ω1 Ω10 Ω100 Ω±(0.2% + 6d)20 MΩ 1KΩ±(1% + 10d)600V DC or Peak- FREQUENCYRange Resolution Accuracy Over Load Protection20 KHz 1 Hz ±(1.5% + 5d)200 KHz 10 Hz ±(2.0% + 5d)600V DC or Peak Frequencies under 500Hz requires a minimum amplitude of at least 4Vpp, other sensitivities are not specified.* The digit error(less than 5digits) is added in measuring value.- AUDIBLE CONTINUITYTest Volt Threshold Over Load Protection 3V Less Than 200 ohm 600V DC or Peak- DIODE TESTTest Volt Max. Test Current Over Load Protection 2V Approx. 1.0 mA 600V DC or PeakDIMENSION AND WEIGHT• Dimensions HWD: 9.4 x 3.5 x 10.6” (240 x 90 x 270mm)• Weight Aprox : 4.6lb (2.1 kg.)1-3. Equipment RatingsPlug and Socket : 3 wire ac power plug and 3 wire outletPower & Fuse RatingsInput Voltage Fuse Power Max.103 ∼ 126V AC (50/60Hz) F 0.5A / 250V206 ∼ 252V AC (50/60Hz) F 0.2A / 250V10 WTemperature : 0°C to + 40 °C (Accuracy Specified at 23 °C ± 5 °C) Temperature Coefficient : 0.1x( Specified Accuracy) per°CHUMIDITY: up to 85% RH (Relative Humidity) to 40°C without temperature extremes causing condensation within the instrument.Storage Environment:TEMPERATURE: -20°C to +70°C HUMIDITY: below 85% RHInsulation Category II: Portable equipment of local level.Pollution Degree: 2Protection to IEC 529: OrdinaryNote: Specifications and information are subject to change without notice. Please visit for the most current product information. 1-4. Supplied AccessoriesUser’s Manual ----------------------------------------------------- 1Test Leads---------------------------------------------------------- 1Power cord---------------------------------------------------------- 1Spare Fuse--------------------------------------------------------- 11-5. International electrical symbolSAFETY RULESRemember: THINK SAFETY AND ACT SAFELY.Read these operating instructions thoroughly and completely before operating this meter.Pay particular attention to WARNINGS used for conditions and actions that pose hazard to the user and CAUTIONS used for conditions and actions that may damage the meter.Always to inspect this meter, test probes and accessories for any sign of damage or abnormality before every use.Never ground yourself and keep your body isolated from ground.Never touch exposed wiring, connections or any live circuit conductors.Disconnect the live test probe before disconnecting the common test probe. Use caution when working above 60V DC or 25V AC rms. Such voltages posea shock hazard.SAFETY SYMBOLS2. INSTALLATION2-1. Initial InspectionThis instrument was carefully inspected both mechanically and electrically before shipment. It should be physically free of damage. To confirm this, the instrument should be inspected for physical damage which may have occurred in transit. Also, verify that all supplied accessories have been included.2-2. Connecting AC PowerThis instrument requires 115V AC or 230V AC (50-60 Hz) power socket with protective earth contact (PE-contact). If it is available only a power socket without PE-contact (so a 2-conductor ac power) then a power socket with PE-contact must be installed before or the appliance should be provided with a PE-screw-terminal which is not soluble by hand and not soluble before 2-conductor power lines.CAUTIONAC POWER OF THIS INSTRUMENT IS PRESET TO 115V IN FACTORY. BEFORE POWERING ON THIS INSTRUMENT, CHECK AND MAKE SURE THE VOLTAGE OF THE POWER SOURCE IS SAME WITH THE MARKING OF UNIT. IN CASE OF AC230V, VOLTAGE SELECTOR (on rear panel) SHOULD BE SELECTED TO 230V POSITION.2-3. Cooling and VentilationNo special cooling and ventilation is required. However, the instrument should be operated where the ambient temperature is maintained.2-4. PositionThis instrument is built as a bench-type instrument with rubber feet and tilt stand in place. The stand-up angle can be adjusted by changing the angle of the carrying handle.2-5. Warming-UpAllow at least 30 minutes for the unit to warm up so that it can stabilize.3. OPERATION3-1 Voltage MeasurementVoltage is the difference of electrical energy (potential) between two points. Measuring voltage allows you to verify the following questions.Is voltage present? The presence of voltage tells you that the circuit is delivering voltage to the component you are testing.What is the level of voltage? The voltage level tells you that whether the proper voltage is arriving at the components.What is the voltage drop? The voltage drop tells you how much of voltage is being consumed by the components.WARNING---HIGH VOLTAGETO AVOID POSSIBLE ELECTRIC SHOCK AND/OR EQUIPMENT DAMAGE, DO NOT ATTEMPT TO TAKE ANY VOLTAGE MEASUREMENTS IF THE VOLTAGE IS ABOVE 1200V DC OR 1000V AC. THE "COM" TERMINAL POTENTIAL SHOULD NOT EXCEED 500V TO THE GROUND.(1) Plug the red and the black test leads into the VΩ and the COM input terminals respectively.(2) Verify dc or ac. Select the function (dc V or ac V) and set the range switch to the desired volt range. For unknown voltage, always start from highest range and move down to lower range to select scale for best reading.(3) Connect the probe tips in parallel with the voltage source to be measured.(4) Read voltage value on the Display.3-2 Current MeasurementCurrent is the flow quantity of electrons through a conductor. Ampere is the amount of electrons flowing through a conductor.CAUTIONDO NOT ATTEMPT TO TAKE A CURRENT OF MORE THAN SPECIFIED. ALWAYS START WITH THE HIGHEST RANGE FOR UNKNOWN CURRENT. THE “mA INPUT” TERMINAL IS PROTECTED BY A 2000mA/250V F TYPE FUSE AND “A INPUT” TERMINAL IS FUSED WITH 15A/250V T TYPE.WARNINGMAKE SURE OF NO POWER BEFORE DISCONNECTING CIRCUIT. EVEN SMALL AMOUNT OF CURRENT CAN BE DANGEROUS. DO NOT ATTEMPT A CURRENT MEASUREMENT WHERE VOLTAGE IS ABOVE 600 V. IF THE FUSE BLOWS, YOU MIGHT BE INJURED OR THE METER DAMAGED.(1) Plug the red test leads into the “mA input” for less than 2000 mA/dc or into “A input” terminal between 2000mA and 20A.(2) Plug the black test leads into the COM input terminal.(3) Verify dc or ac. Select the function (dc A or ac A) and set the range switch to the desired volt range. For unknown current, always start from highest range and move down to lower range to select scale for best reading.(4) Connect the probe tips in series with the current source to be measured.(5) Read current value on the Display.(6) Fuse ReplacementDisconnect and remove all connections from any live power source.Open the top case.Locate the defective fuse and remove it in input board.Install a new fuse of the SAME SIZE AND RATING.Close the top case.** 20 A ac/dc Measurement - “Max . 15sec each 15minute”3-3 Resistance MeasurementResistance is an obstacle that is hindering the current flowing through a conductor. Ohm is the unit of this resistance.The resistance displayed in meter is the total resistance through all possible paths between red and black probes.Resistance must always be measured with meter in series with the circuit.Resistance in test lead is about 0.1 - 0.2 ohmBe sure that the contact between the probes and the circuit is clean. Contact resistance coming from dirt, oil, paint, etc. can affect accuracy seriously.CAUTIONALL RESISTANCE MEASUREMENTS SHOULD BE TAKEN ON DE-ENERGIZED CIRCUITS ONLY. COMPLETELY DE-ENERGIZE THE CIRCUIT OR DEVICE WHICH IS TO BE MEASURED. POWER TO THE CIRCUIT UNDER TEST MUST BE OFF AND ANY CAPACITORS SHOULD BE DISCHARGED. IF AN EXTERNAL VOLTAGE IS PRESENT ACROSS A COMPONENT, IT WILL CAUSE ERRONEOUS RESISTANCE READING.(1) Plug the red and black test leads into the VΩ input and the COM input terminalsrespectively.(2) Select the function(OHM) and set the range switch to the desired resistancerange.(3) Connect the probe tips in parallel with the resistance to be measured.(4) Read resistance value on the Display.3-4 Diode MeasurementA good diode allows current in one direction. To test a single diode, turn the power off and remove the diode from circuit.(1) Connect the red probe to the plus(+) side of diode and the black probe to theminus(-) side.(2) If diode is good, the voltage drop will be displayed. (ex : 300.0 ~ 800.0 )(3) Reveres the probes and measure the voltage across the diode again.If diode is good, the display shows “000.0” and is flickering.If diode is shorted, the display shows 000.0 with beep sound in both direction. If display shows “000.0” and is flickering in both directions, the diode is open.3-5 Continuity testContinuity test verifies by beeper if the circuit is closed or open.Meter detects opens and shorts.(1) Set the push switch to continuity function & diode range.(2) Connect the probes to the circuit and listen for beeper. Continuity tone confirmsthat the circuit is continued, closed and connected.3-6 Frequency Measurement(1) Plug the red and black test leads into the VΩ input and the COM input terminals respectively.(2) Select the function to FRQ. and set the range switch to the desired frequency range. For unknown frequency, always start from highest range and move down to lower range to select scale for best reading.(3) Connect the probe tips in parallel with the circuit to be measured.(4) Read frequency value on the Display.NOTE ;The digit error (less than 5digits) is added in measuring value.To compensate this error, check the digit error by shorting test leads(+,-) before measuring unknown frequency and deduct this value from measuring value.4. MAINTENANCECAUTIONIT IS ESSENTIAL FOR SAFETY TO PROPERLY MAINTAIN AND SERVICE THIS INSTRUMENTWARNINGVOLTAGES WITHIN THIS INSTRUMENT ARE SUFFICIENTLY HIGH TO ENDANGER LIFE. COVERS MUST NOT BE REMOVED EXCEPT BY PERSONS QUALIFIED AND AUTHORIZED TO DO SO AND THESE PERSONS SHOULD ALWAYS TAKE EXTREME CARE ONCE THE COVERS HAVE BEEN REMOVED.4-1. Fuse ReplacementDisconnect and remove all connections from any live power source.Unscrew fuse holder by screw driver.Locate the defective fuse and remove it by gently pulling-out.Install a new fuse of the SAME SIZE AND RATING.Screwing fuse holder.CAUTIONMAKE SURE THAT THE RATED AND SPECIFIED FUSES ARE USED FOR REPLACEMENT.4-2. Adjustment And CalibrationIt is recommendable to regularly adjust and calibrate this instrument. Qualified and authorized personnel only should execute performance and procedures.4-3. Cleaning and decontaminationThe instrument can be cleaned with a soft clean cloth to remove any oil, grease or grime. Never use liquid solvents or detergents. If the instrument gets wet for any reason, dry the instrument using low-pressure clean air at less than 25 PSI. Use care and caution around the window cover areas where water or air could enter into the instrument while drying.Limited One-Year WarrantyB&K Precision Corp. warrants to the original purchaser that its product and the component parts thereof, will be free from defects in workmanship and materials for a period of one year from the data of purchase.B&K Precision Corp. will, without charge, repair or replace, at its’ option, defective product or component parts. Returned product must be accompanied by proof of the purchase date in the form a sales receipt.To obtain warranty coverage in the U.S.A., this product must be registered by completing and mailing the enclosed warranty card to B&K Precision Corp., 22820 Savi Ranch Parkway, Yorba Linda, CA 92887 within fifteen (15) days from proof of purchase.Exclusions: This warranty does not apply in the event of misuse or abuse of the product or as a result of unauthorized alternations or repairs. It is void if the serial number is alternated, defaced or removed.B&K Precision Corp. shall not be liable for any consequential damages, including without limitation damages resulting from loss of use. Some states do not allow limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.This warranty gives you specific rights and you may have other rights, which vary from state-to-state.Model Number: ______________ Date Purchased:__________Service InformationWarranty Service: Please return the product in the original packaging with proof of purchase to the below address. Clearly state in writing the performance problem and return any leads, connectors and accessories that you are using with the device.Non-Warranty Service: Return the product in the original packaging to the below address. Clearly state in writing the performance problem and return any leads, connectors and accessories that you are using with the device. Customers not on open account must include payment in the form of a money order or credit card. For the most current repair charges contact the factory before shipping the product.Return all merchandise to B&K Precision Corp. with pre-paid shipping. The flat-rate repair charge includes return shipping to locations in North America. For overnight shipments and non-North America shipping fees contact B&K Precision Corp..B&K Precision Corp.22820 Savi Ranch ParkwayYorba Linda, CA 92887Phone: 714- 921-9095Facsimile: 714-921-6422Include with the instrument your complete return shipping address, contact name, phone number and description of problem.22820 Savi Ranch Parkway Yorba Linda, CA 92887 USA TEL: 714-921-9095 FAX: 714-921-6422 PN: 481-532-9-001 Printed in Korea©2004 B&K Precision Corp.。

Product # SL903RK3-120W Project Comments Prepared ByREVIVE LED Retrofit KitHID Lamp ReplacementVersion 2.0© 2017 Straits Lighting Company | | Detroit | Phone: 855 - 875 - 2533 | Fax: 248 - 671 - 0624 PRODUCT DETAILSCCT Input(VAC)Lumens (lm)2ReplacesCRI100/277V 15,236.08 400W MH/HPS 73 73400W MH/HPS2. In fixture @ 5000KShoebox Floodlight Cobrahead Wall Packs High/Low Bays CanopyStraits Lighting LED Retrofit Kits are designed to retrofit any HID fixture using custom fabricated brackets. Save time, money, and jobsite waste by retrofitting existing HID fixtures—all while enhancing light levels. Premium Nichia LED chips deliver best in class efficacy, and are backed by our 10 year warranty.Retrofit existing HID Fixtures to save time, money, and jobsite wasteLED - RETROFIT KIT© 2017 Straits Lighting Company | | Detroit | Phone: 855 - 875 - 2533 | Fax: 248 - 671 - 0624The Straits Lighting Company is constantly developing and improving its products. For this reason, all product descriptions in this brochure are intended as a general guide, and we may change specifications from time to time in the interest of product development, without prior notification or public announcement. All descriptions in this publication present only general particulars of the goods to which they refer and shall not form part of any contract. Data in this guide has been obtained in controlled experimental conditions. However, The Straits Lighting Company cannot accept any liability arising from the reliance on such data to the extent permitted.PRODUCT DIMENSIONS (mm)CONTACT USORDERING INFORMATIONSAMPLE NUMBER: SL903RK3-120W -SU -50K-D -MPRIOR TO INSTALLATION♦ Make certain power is OFF before starting installation or maintenance. ♦ Proper grounding is required to ensure personal safety. ♦ Do not recess the fixture.♦ Only attempt installation if qualified electrician.♦ DO NOT TOUCH THE LED CHIPS. DAMAGE MAY OCCUR.♦ Installer must affix a warning label to the fixture, which announces thefixture has been retrofitted.。

T h e i n f o r m a t i o n p r o v i d e d i n t h i s d o c u m e n t a t i o n c o n t a i n s g e n e r a l d e s c r i p t i o n s a n d /o r t e c h n i c a l c h a r a c t e r i s t i c s o f t h e p e r f o r m a n c e o f t h e p r o d u c t s c o n t a i n e d h e r e i n .T h i s d o c u m e n t a t i o n i s n o t i n t e n d e d a s a s u b s t i t u t e f o r a n d i s n o t t o b e u s e d f o r d e t e r m i n i n g s u i t a b i l i t y o r r e l i a b i l i t y o f t h e s e p r o d u c t s f o r s p e c i f i c u s e r a p p l i c a t i o n s .I t i s t h e d u t y o f a n y s u c h u s e r o r i n t e g r a t o r t o p e r f o r m t h e a p p r o p r i a t e a n d c o m p l e t e r i s k a n a l y s i s , e v a l u a t i o n a n d t e s t i n g o f t h e p r o d u c t s w i t h r e s p e c t t o t h e r e l e v a n t s p e c i f i c a p p l i c a t i o n o r u s e t h e r e o f .N e i t h e r S c h n e i d e r E l e c t r i c I n d u s t r i e s S A S n o r a n y o f i t s a f f i l i a t e s o r s u b s i d i a r i e s s h a l l b e r e s p o n s i b l e o r l i a b l e f o r m i s u s e o f t h e i n f o r m a t i o n c o n t a i n e d h e r e i n .Product data sheetCharacteristicsATS01N206QNsoft starter for asynchronous motor - ATS01 - 6A - 380..415V - 1.5..3 KWProduct availability: Non-Stock - Not normally stocked in distribution facilityMainRange of product Altistart 01Product or component typeSoft starterProduct destination Asynchronous motors Product specific applica-tionSimple machine Device short name ATS01Phase3 phase[Us] rated supply volt-age380...415 V - 10...10 %Motor power kW3 KW, 3 phase 380...415 V 1.5 KW, 3 phase 380...415 V 2.2 kW, 3 phase 380...415 V IcL starter rating 6 AUtilisation category AC-53B EN/IEC 60947-4-2Current consumption 30 A at nominal load Type of startStart with voltage rampPower dissipation in W4 W at full load and at end of starting 64 W in transient stateComplementaryAssembly style With heat sink Function available Integrated bypass Supply voltage limits 342…456 V Supply frequency 50...60 Hz - 5...5 %Network frequency 47.5...63 HzOutput voltage<= power supply voltage [Uc] control circuit voltage Built into the starter Starting time1 s / 1005 s / 2010 s / 10Adjustable from 1 to 10 s Deceleration time symb Adjustable from 1 to 10 sStarting torque 30...80 % of starting torque of motor connected directly on the line supply Discrete input type Logic LI1, LI2, BOOST) stop, run and boost on start-up functions <= 8 mA 27kOhm Discrete input voltage 24...40 VDiscrete input logic Positive LI1, LI2, BOOST < 5 V <= 0.2 mA > 13 V, >= 0.5 mA Discrete output current 2 A DC-133 A AC-15Discrete output type Open collector logic LO1 end of starting signal Relay outputs R1A, R1C NO Discrete output voltage 24 V 6...30 V) open collector logic Minimum switching current 10 mA 6 V DC relay outputsMaximum switching current Relay outputs 2 A 250 V AC cos phi = 0.5 20 ms inductive Relay outputs 2 A 30 V DC cos phi = 0.5 20 ms inductive Display type 1 LED green)starter powered up1 LED yellow)nominal voltage reached Tightening torque16.82…22.13 Lbf.In (1.9…2.5 N.m)4.43 lbf.in (0.5 N.m)Electrical connection 4 mm screw clamp terminal - rigid 1 1...10 mm² AWG 8 power circuitScrew connector - rigid 1 0.5...2.5 mm² AWG 14 control circuit4 mm screw clamp terminal - rigid 2 1...6 mm² AWG 10 power circuitScrew connector - rigid 2 0.5...1 mm² AWG 17 control circuitScrew connector - flexible with cable end 1 0.5...1.5 mm² AWG 16 control circuit4 mm screw clamp terminal - flexible without cable end 1 1.5...10 mm² AWG 8power circuitScrew connector - flexible without cable end 1 0.5...2.5 mm² AWG 14 control cir-cuit4 mm screw clamp terminal - flexible with cable end 2 1...6 mm² AWG 10 powercircuit4 mm screw clamp terminal - flexible without cable end 2 1.5...6 mm² AWG 10power circuitScrew connector - flexible without cable end 2 0.5...1.5 mm² AWG 16 control cir-cuitMarking CEOperating position Vertical +/- 10 degreeHeight 4.88 in (124 mm)Width 1.77 in (45 mm)Depth 5.16 in (131 mm)Net weight0.93 lb(US) (0.42 kg)Compatibility code ATS01N2Motor power range AC-3 1.1…2 KW 380…440 V 3 phase2.2…3 kW 380…440 V 3 phaseMotor starter type Soft starterEnvironmentElectromagnetic compatibility Conducted and radiated emissions level B CISPR 11Conducted and radiated emissions level B IEC 60947-4-2Damped oscillating waves level 3 IEC 61000-4-12Electrostatic discharge level 3 IEC 61000-4-2EMC immunity EN 50082-1EMC immunity EN 50082-2Harmonics IEC 1000-3-2Harmonics IEC 1000-3-4Immunity to conducted interference caused by radio-electrical fields level 3 IEC61000-4-6Immunity to electrical transients level 4 IEC 61000-4-4Immunity to radiated radio-electrical interference level 3 IEC 61000-4-3Micro-cuts and voltage fluctuation IEC 61000-4-11Voltage/current impulse level 3 IEC 61000-4-5Standards EN/IEC 60947-4-2Product certifications ULB44.1-96/ASME A17.5 for starter wired to the motor delta terminalCSAGOSTC-TickCCCIP degree of protection IP20Pollution degree 2 EN/IEC 60947-4-2Vibration resistance 1 gn 13…150 Hz)EN/IEC 60068-2-61.5 mm peak to peak 3…13 Hz)EN/IEC 60068-2-6Shock resistance15 gn 11 ms EN/IEC 60068-2-27Relative humidity5…95 % without condensation or dripping water EN/IEC 60068-2-3Ambient air temperature for operation14…104 °F (-10…40 °C) without)104…122 °F (40…50 °C) with current derating of 2 % per °C)Ambient air temperature for storage-13…158 °F (-25…70 °C) EN/IEC 60947-4-2Operating altitude<= 3280.84 ft (1000 m) without> 3280.84 ft (1000 m) with current derating of 2.2 % per additional 100 m Ordering and shipping detailsCategory22392 - ATSU01/ATS01 LOW HP SOFT STARTERSDiscount Schedule I11GTIN00785901457671Package weight(Lbs)0.50 kg (1.11 lb(US))Returnability NoCountry of origin DEOffer SustainabilityREACh Regulation REACh DeclarationREACh free of SVHC YesEU RoHS Directive Pro-active compliance (Product out of EU RoHS legal scope)EU RoHS Decla-rationToxic heavy metal free YesMercury free YesRoHS exemption information YesChina RoHS Regulation China RoHS DeclarationWEEE The product must be disposed on European Union markets following specificwaste collection and never end up in rubbish bins.Contractual warrantyWarranty18 monthsDimensions DrawingsDimensionsMounting on Symetrical (35 mm) RailScrew Fixing(1)Retractable fixingsConnections and SchemaExample of Manual ControlA1 :Soft start/soft stop unit (1)For type 2 coordination Q1 :Motor circuit-breaker F3 : 3 fast-acting fusesTechnical DescriptionFunction Diagram2-wire Control with DecelerationUs :Power supply voltage LED 1 :Green LED LI2 :Logic input R1 :Relay output LO1 :Logic output LED 2 :Yellow LED3-wire Control with DecelerationUs :Power supply voltage LED 1 :Green LED LI2,LI1 :Logic inputs R1 :Relay output LO1 :Logic output Um :Motor voltage LED 2 :Yellow LED。

2Pin螺丝端子+O型连接端子+双层绝缘层输出线+鳄鱼夹230V 2Pin螺丝端子+O型连接端子+双层绝缘层输出线+鳄鱼夹230V 2Pin螺丝端子(无输出线) 固顺+黑白双线(开线尾) 固顺+黑白双线(开线尾) 线扣+1.2m小双层绝缘层的输出线(开线尾) 2PIN黑色塑胶端子 2PIN黑色塑胶端子 3PIN圆形母插座 2PIN黑色塑胶端子 香蕉插座 100-240V 100-240V 100-240V 100-240V 230V 100-240V 230V 100-240V 100-240V 100-240V 100-240V
/ / / / / / / / / / / /
12V20A Battery charger 24V17A Battery Charger 48V18A Battery Charger 12V50A Battery Charger Lithium Polymer Charger 16.8V 2.5A Lithium Polymer Charger 33.6V 1.2A Lithium Polymer Charger 33.6V 4A Lithium Polyme Charger 33.6V 9A Lithium Polymer Charger 29.8V 34A Lithium Polymer Charger 29.4V 34A Lithium Polymer Charger 67.2V 15A SPS 12-14V 6A
无
Hale Waihona Puke 无外观 喷油 黑色光面,下盖贴贴纸 暗红色(PANTONE 186C) 黑色光色,下盖贴贴纸 深灰色上盖和底壳,银色前板 深灰色上盖和底壳,银色前板 深灰色上盖和底壳,银色前板 深灰色上盖和底壳,银色前板 深灰色上盖和底壳,银色前板 全套金属银(砂面) 萤光橙 黑色光面,下盖贴贴纸 内盒 吸塑+彩卡 彩盒 白盒 白盒 白盒 白盒 白盒 白盒 白盒 白盒