NRLM222M450V30X30XF中文资料

Large Can Aluminum Electrolytic CapacitorsFEATURES• LONG LIFE (105°C, 2000 HOURS)• LOW PROFILE AND HIGH DENSITY DESIGN OPTIONS • EXPANDED CV VALUE RANGE• HIGH RIPPLE CURRENT• CAN-TOP SAFETY VENT • DESIGNED AS INPUT FILTER OF SMPS• STANDARD 10mm (.400") SNAP-IN SPACING NRLMW SeriesSPECIFICATIONSNotice for MountingThe space from the top of the can shall be more than (3mm) from chassis or other construction materials so that safety vent has room to expand in case of emer g en c y.Sleeve Color: Dark BlueCan Top Safety VentInsulation Sleeve and Minus Polarity Marking(4.0mm Leads Available As Option)D+1Max.L ± 26.3 ± 10.810(-)(+)MAXIMUM EX P AN S IONFOR SAFETY VENT Approx. 3.0mmRecommended PC Board Mounting Holes:10 ± .1∅= 2 ± 0.1D ∅ ± 0.5ChassisPC BoardPRECAUTIONSPlease review the notes on correct use, safety and precautions found on pages T10 & T11of NIC’s Electrolytic Capacitor catalog . Operating Temperature Range-40 ~ +105°C -25 ~ +105°C Rated Voltage Range 10 ~ 250Vdc 450Vdc Rated Capacitance Range 180 ~ 68,000µF 56 ~ 470µF Capacitance Tolerance ±20% (M) at 120Hz, +20°CMax. Leakage Current (µA)After 5 minutes (20°C)3 x C(µF)VMax. Tan δat 120Hz/20°CW.V. (Vdc)10162535506380100 ~ 400450Tan δ max.0.550.450.350.300.250.200.170.150.20Surge VoltageW.V. (Vdc)10162535506380100160S.V. (Vdc)132032446379100125200W.V. (Vdc)180200250400450----S.V. (Vdc)220250300450500----Ripple Current Correction Factors Frequency (Hz)50601001205001K 10K ~ 50K --Multiplier at 85°C16 ~ 100Vdc0.930.950.99 1.0 1.05 1.08 1.15--160 ~ 450Vdc0.750.800.95 1.0 1.20 1.25 1.40-Low Temperature Stability (10 to 250Vdc)Temperature (°C)0-25-40------Capacitance Change -5%-10-30%------Impedance Ratio 1.539------Load Life Test 2,000 hours at +105°C Capacitance ChangeWithin ±20% of initial measured valueTan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Shelf Life Test 1,000 hours at +105°C(no load)Capacitance ChangeWithin ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Surge Voltage TestPer JIS-C-5141 (table #6, #4)Surge voltage applied: 30 seconds "On" and 5.5 minutes no voltage "Off"Capacitance ChangeWithin ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Soldering EffectRefer toMIL-STD-202F Method 210ACapacitance ChangeWithin ±10% of initial measured valueTan δLess than specifi ed maximum value Leakage CurrentLess than specifi ed maximum valueRoHSCompliantincludes all homogeneous materials *See Part Number System for DetailsLarge Can Aluminum Electrolytic Capacitors NRLMW SeriesLarge Can Aluminum Electrolytic CapacitorsNRLMW SeriesNRLMW 471 M 250V 30X35 FRoHS compliant Case Size (mm) Voltage Rating Tolerance Code Capacitance Code SeriesPART NUMBER SYSTEM。

Operating Temperature Range-40 ~ +85°C-25 ~ +85°C Rated Voltage Range10 ~ 250Vdc315 ~ 450Vdc Rated Capacitance Range180 ~ 82,000µF56 ~ 1,000µF Capacitance Tolerance±20% (M)Max. Leakage Current (µA)After 5 minutes (20°C)3 x C(µF)VMax. Tan δat 120Hz/20°C W.V. (Vdc)10162535506380100160~400420~450 Tan δ max.0.550.500.450.400.350.300.250.200.150.25Surge Voltage W.V. (Vdc)10162535506380100160180 S.V. (Vdc)132032446379100125200220 W.V. (Vdc)200220250315350385400420450-S.V. (Vdc)250270300365400435450470500-Ripple Current Correction FactorsFrequency (Hz)50 (60)1205001K10K>-----Multiplierat 85°C10 ~ 100Vdc0.90 1.00 1.05 1.10 1.15-----160 ~ 250Vdc0.80 1.00 1.20 1.30 1.50-----315 ~ 450Vdc0.80 1.00 1.20 1.25 1.40-----Low Temperature Stability (10 to 250Vdc)Temperature (°C)0-25-40-------Capacitance Change-5%-15%-30%-------Impedance Ratio 1.5312-------Load Life Test 3,000 hours at +85°C Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum value Leakage Current Less than specifi ed maximum valueShelf Life Test 1,000 hours at +85°C(no load)Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum value Leakage Current Less than specifi ed maximum valueSurge Voltage TestPer JIS-C-5141 (table #6, #4) Surge voltage applied: 30 seconds "On" and 5.5 minutes no voltage "Off"Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum value Leakage Current Less than specifi ed maximum valueSoldering Effect Refer to JISC5102.8.5Capacitance Change Within ±10% of initial measured value Tan δLess than specifi ed maximum value Leakage Current Less than specified maximum valueLarge Can Aluminum Electrolytic Capacitors NRLR Series FEATURES• EXPANDED VALUE RANGE• LONG LIFE AT +85°C (3,000 HOURS)• HIGH RIPPLE CURRENT• LOW PROFILE, HIGH DENSITY DESIGN• SUITABLE FOR SWITCHING POWER SUPPLIESSPECIFICATIONSMECHANICAL CHARACTERISTICS:1. Safety Vent:The capacitors are provided with a pressure sensitive safety vent on the top of can. The vent is designed to rupture in the event that high internal gas pressure is developed by circuit mal f unc t ion or mis-use like reverse voltage.2. Terminal Strength:Each terminal of the capacitor shall withstand an axial pull force of 4.5Kg for a period 10 seconds or a radial bent force of 2.5Kg for a periodof 30 seconds.NRLR 222 M 50V 20X25 S FRoHS compliantLead Length (S=4mm, L=6mm)Case Size (mm)Voltage RatingTolerance CodeCapacitance CodeSeriesPART NUMBER SYSTEMPRECAUTIONSPlease review the notes on correct use, safety and precautions found on pages T10 & T11of NIC’s Electrolytic Capacitor catalog.Notice for MountingThe space from the top of the can shall be more than (3mm) from chassis orRecommended PC Board Mounting Holes: Sleeve Color: Dark BlueCan Top Safety VentInsulation Sleeve and MinusPolarity MarkingD+1Max.L ± 2 4.0 ± 1or6.3 ± 110(-)(+)SAFETY VENT∅= 2ChassisRoHSCompliantincludes all homogeneous materials*See Part Number System for DetailsLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR SeriesLarge Can Aluminum Electrolytic Capacitors NRLR Series STANDARD PRODUCT LIST, CASE SIZE AND SPECIFICATIONS160Large Can Aluminum Electrolytic CapacitorsNRLR Series6.0mm - Optional Lead Length元器件交易网。

147®NIC COMPONENTS CORP. www www www www Large Can Aluminum Electrolytic CapacitorsFEATURES• LOW PROFILE (20mm HEIGHT)• LOW DISSIPATION FACTOR AND LOW ESR • HIGH RIPPLE CURRENT • WIDE CV SELECTION• SUITABLE FOR SWITCHING POWER SUPPLIES NRLF SeriesSPECIFICATIONSMECHANICAL CHARACTERISTICS:1. Safety Vent:: The capacitors are provided with a pressure sensitive safety vent on the top. The vent is designed torupture in the event that high internal gas pressure is developed by circuit mal f unc t ion or mis-use like reverse voltage.2. Terminal Strength: Each terminal of the capacitor shall withstand an axial pull force of 4.5Kg for a period 10 seconds or a radial bent force of 2.5Kg for a period of 30 seconds.Notice for MountingThe space from the top of the can shall be more than (3mm) from chassis or other construction materials so that safety vent has room to expand in case of emer g en c y.Sleeve Color: Dark BlueCan Top Safety VentInsulation Sleeve and Minus Polarity Marking(4.0mm Leads Available As Option)D+1Max.L ± 26.3 ± 10.810(-)(+)MAXIMUM EX P AN S IONFOR SAFETY VENT Approx. 3.0mmPC Board Mounting Holes:10 ± .1∅= 2 ± 0.1D ∅ ± 0.5PC BoardOperating Temperature Range-40 ~ +85°C-25 ~ +85°C Rated Voltage Range 16 ~ 250Vdc 350 ~ 450Vdc Rated Capacitance Range 100 ~ 15,000µF33 ~ 150µFCapacitance Tolerance ±20% (M)Max. Leakage Current (µA)After 5 minutes (20°C)3 x C(µF)VMax. Tan δat 120Hz/20°C W.V. (Vdc)162535506380100160~450Tan δ max.0.500.400.350.300.250.200.200.15Surge VoltageW.V. (Vdc)162535506380100160S.V. (Vdc)2032446379100125200W.V. (Vdc)180200250350400450--S.V. (Vdc)220250300400450500--Ripple CurrentCorrection FactorsFrequency (Hz)50601001205001K 10K ~ 50K -Multiplier at 85°C 16 ~ 100Vdc 0.930.950.99 1.00 1.05 1.08 1.15-160 ~ 450Vdc 0.750.800.95 1.0 1.20 1.25 1.40Low TemperatureStability (16 to 250Vdc)Temperature (°C)0-25-40-----Capacitance Change-5%-10-30%-----Impedance Ratio 1.539-----Load Life Test2,000 hours at +85°CCapacitance ChangeWithin ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Shelf Life Test1,000 hours at +85°C (no load)Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Surge Voltage Test Per JIS-C-5141 (table #6, #4)Surge voltage applied: 30 seconds"On" and 5.5 minutes no voltage "Off"Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Soldering EffectRefer to MIL-STD-202F Method 210A Capacitance Change Within ±10% of initial measured valueTan δLess than specifi ed maximum value Leakage Current Less than specifi ed maximum valuePRECAUTIONSPlease review the notes on correct use, safety and precautions found on pages T10 & T11of NIC’s Electrolytic Capacitor catalog . Also found at /precautionsIf in doubt or uncertainty, please review your speci fi c application - process details withNIC’s technical support personnel: tpmg@RoHS Compliantincludes all homogeneous materials*See Part Number System for Details148Large Can Aluminum Electrolytic CapacitorsNRLF SeriesNRLF 152 M 50V 22X20 FRoHS compliant Case Size (mm) Voltage Rating Tolerance Code Capacitance Code SeriesPART NUMBER SYSTEM。

147®NIC COMPONENTS CORP. www www www www Large Can Aluminum Electrolytic CapacitorsFEATURES• LOW PROFILE (20mm HEIGHT)• LOW DISSIPATION FACTOR AND LOW ESR • HIGH RIPPLE CURRENT • WIDE CV SELECTION• SUITABLE FOR SWITCHING POWER SUPPLIES NRLF SeriesSPECIFICATIONSMECHANICAL CHARACTERISTICS:1. Safety Vent:: The capacitors are provided with a pressure sensitive safety vent on the top. The vent is designed torupture in the event that high internal gas pressure is developed by circuit mal f unc t ion or mis-use like reverse voltage.2. Terminal Strength: Each terminal of the capacitor shall withstand an axial pull force of 4.5Kg for a period 10 seconds or a radial bent force of 2.5Kg for a period of 30 seconds.Notice for MountingThe space from the top of the can shall be more than (3mm) from chassis or other construction materials so that safety vent has room to expand in case of emer g en c y.Sleeve Color: Dark BlueCan Top Safety VentInsulation Sleeve and Minus Polarity Marking(4.0mm Leads Available As Option)D+1Max.L ± 26.3 ± 10.810(-)(+)MAXIMUM EX P AN S IONFOR SAFETY VENT Approx. 3.0mmPC Board Mounting Holes:10 ± .1∅= 2 ± 0.1D ∅ ± 0.5PC BoardOperating Temperature Range-40 ~ +85°C-25 ~ +85°C Rated Voltage Range 16 ~ 250Vdc 350 ~ 450Vdc Rated Capacitance Range 100 ~ 15,000µF33 ~ 150µFCapacitance Tolerance ±20% (M)Max. Leakage Current (µA)After 5 minutes (20°C)3 x C(µF)VMax. Tan δat 120Hz/20°C W.V. (Vdc)162535506380100160~450Tan δ max.0.500.400.350.300.250.200.200.15Surge VoltageW.V. (Vdc)162535506380100160S.V. (Vdc)2032446379100125200W.V. (Vdc)180200250350400450--S.V. (Vdc)220250300400450500--Ripple CurrentCorrection FactorsFrequency (Hz)50601001205001K 10K ~ 50K -Multiplier at 85°C 16 ~ 100Vdc 0.930.950.99 1.00 1.05 1.08 1.15-160 ~ 450Vdc 0.750.800.95 1.0 1.20 1.25 1.40Low TemperatureStability (16 to 250Vdc)Temperature (°C)0-25-40-----Capacitance Change-5%-10-30%-----Impedance Ratio 1.539-----Load Life Test2,000 hours at +85°CCapacitance ChangeWithin ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Shelf Life Test1,000 hours at +85°C (no load)Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Surge Voltage Test Per JIS-C-5141 (table #6, #4)Surge voltage applied: 30 seconds"On" and 5.5 minutes no voltage "Off"Capacitance Change Within ±20% of initial measured value Tan δLess than 200% of specifi ed maximum valueLeakage Current Less than specifi ed maximum value Soldering EffectRefer to MIL-STD-202F Method 210A Capacitance Change Within ±10% of initial measured valueTan δLess than specifi ed maximum value Leakage Current Less than specifi ed maximum valuePRECAUTIONSPlease review the notes on correct use, safety and precautions found on pages T10 & T11of NIC’s Electrolytic Capacitor catalog . Also found at /precautionsIf in doubt or uncertainty, please review your speci fi c application - process details withNIC’s technical support personnel: tpmg@RoHS Compliantincludes all homogeneous materials*See Part Number System for Details148Large Can Aluminum Electrolytic CapacitorsNRLF SeriesNRLF 152 M 50V 22X20 FRoHS compliant Case Size (mm) Voltage Rating Tolerance Code Capacitance Code SeriesPART NUMBER SYSTEM。