HP-UX 操作系统安装(详细安装)
安装所需的介质和资料:
HP-UX Core OS Install/Update/Recovery光盘(1张)
HP-UX Support Plus光盘(1张)
HP-UX Application Software光盘(5张)
1.安装前的准备:
在系统的安装之前检查机器的各线连接,将机器通过网线接到hub上,并且在确保各个外设(磁带机.磁盘阵列等)加电后,然后再开机。
我现在重装35的话,需要怎么做呢要umont已有的目录吗
2.在屏幕上将看到:
"Processor is booting from fist available device
To discontinue. press any key within 10 second s"
在10秒之内按任意键,之后屏幕将显示一9个命令集画面:
Main Menu…………………………………………….
Command Description
Boot [PRI|ALT|
……………………… ………………………
……………………… ………………………
……………………… ………………………
Main Menu: Enter command >
3.将Update/Recovery放入光驱或DVD,
4.键入命令SEA,系统会查询硬件设备的物理路径:
Main menu: Enter command >sea
(例如)
Path Number Device path Device Type
P0 8/ Random access media
P1 8/ Random access media
P2 … …………
5.根据'device path如:8/'与机器前门内标注(D250)确定光驱或DVD的路径,
假设为P1 8/
键入命令bo p1回车:
Main Menu: Enter command>bo p1
6 .系统会询问是否要进行交互访问,要输入 n回车
Interact with IPL > n
注意: :接下来可能出现屏幕乱码现象,解决方法:
按User System键,屏幕底出现8个小亮块,最右边一块为
按F8键,8个亮块发生变化,其中有一个为 ,按F5键, 进入TERMINAL CONFIGURATIONJIEMIAN界面,
将TERM MODE项的值改为EM100),然后按F1,保存设置
7.系统要求选择安装方式:
Welcome to the HP-UX installation/recovery process!
Use the
Within the
Use the
Menus are not clear,select the "Help" item for more information.
[Install HP-UX ]
[Run a Recovery Shell]
[Advance Options ]
选择[Install HP-UX],回车继续。
8.屏幕出现: User Interface And Media Optionslllllllll
Source Location Options:
[*] Media only installation
[ ] Media with Network enabled (allows use of SD depots)
[ ] Idnite-UX server based installation
User Interface Option:
[*]Guided Installation (recommand for basic installs)
[ ]Advanced Installation
选择[*]Media only installation和[*]Advanced Installation两项,[*] 为选中状态,然后OK.
8.屏幕出现:
Basic Software System File system Advanced
Configrations:[……………………………………….] [ Description…]
Environments:[……………………………………....] [HP-UX
[Root Disk….]……………………………………………………………
File System :[Logical Volume Manager
[Root Swap(MB)]…… Physical Memory (RAM) =……
[Languages…….]…… [Keyboards…] [Additional….]
对于Basic中的内容不要做任何修改,保留默认值。
9.选中File System,显示如下
(表中数据只是为例,有的数据被省略)
Basic Software System File system Advanced
Mount Dir Usages Size(MB) % used VG Name
/stand HFS 84 24 vg00 [Add]
Primary SWAP+D --- -- ---- [Modify]
/ VxFS -- -- --- [Remove]
Usage :[…..] VG name: [ ] Mount Dir :………..
Size: [Fixed MB ]----- Avail:------
[Add/Remove Disks…] [---Additional Task---]
在这里可以修改各系统文件的空间大小
Type Filesystem kbytes used avail %used Mounted on
hfs /dev/vg00/lvol1 199381/200M 29440 150002 16% /stand
*** /dev/vg00/lvol2 199381/2048M ***** ****** **% /***
vxfs /dev/vg00/lvol3 258048/252M 152942 98537 61% /
vxfs /dev/vg00/lvol4 1048576/1024M 1357 981768 0% /home
vxfs /dev/vg00/lvol5 1048576/1024M 309329 693045 31% /opt
vxfs /dev/vg00/lvol6 512000/500M 1449 478642 0% /tmp
vxfs /dev/vg00/lvol7 1048576/1024M 530219 485960 52% /usr
vxfs /dev/vg00/lvol8 2097152/2048M 397013 1593881 20% /var
vxfs /dev/vg00/lvol9 2097152/2048M 1776350 300752 86% /sybase
根据要求设置各文件系统的大小与下表一致:
Mount Dir L2000(MB) Usage
Primary swap xxx Swap+D
/ xxx VxFS
/stand xxx HFS
/var xxx VxFS
/usr xxx VxFS
/Tmp xxx VxFS
/Opt xxx VxFS
/home xxx VxFS
如果屏幕上的各个文件系统的缺省值与用户要求不一样,要进行修改,
每次修改之后要按Modify项确认,以便保留设置。
设置完毕,GO,继续下一步。
这些文件系统的大小怎么确认是在重装之前备份系统,还是手工记录
10.接着系统会提示被安装的硬盘上的原有数据将被破坏,选GO,继续。11.这时候系统文件的安装开始,屏幕显示,
Loading configuratio n utilitys……..
*Starting system configuration…….
*…………………………………..
………………………………………
整个过程包括710个文件的安装,需要较长时间(大约2小时),请耐心等待,最后系统自动重启两次,显示大大的OK字样,提示安装成功。
12.重启后,,系统要求配置网络
Are you ready to link this system to a network
Press[y]for yes or [n] for no .then press [Return]
键入y,回车
13.系统询问是否使用DHCP:
Do you wish to use DHCP to obtain networking information ?
Press [y] for yes or [n] for no .then press [Return]
键入n,回车
14.系统询问是否继续下面的主机名。Ip地址。时间的配置:
*Your system name (host name)
*Your internet protocol (IP0 address.
*Your time zone
Are you wish to continue (answering no will HALT the system)?
Press [y] for yes or [n] for no .then press [Return]
键入y,回车
15.接着下一个画面底下两行将显示:
Enter the system name ,,then press [Return].Just pressing [Return]will keep the (not recommended)name "unhost": root
在光标处输入你想要的系统名,例如root然后回车
然后系统询问是否正确:
You have chosen root as the name for this system .
Is this correct?
Press [y] for yes or [n] for no .then press [Return]
键入y,回车
16.屏幕要求你选择你所在的位置:
1) North America or Hawaii
2) Central America
3) South America
4) Europe
5) Africa
6) Asia
7) Australia,New Zealand
Enter the number for your location (1-70then press [return]
键入6,选择Asia ,然后回车
17.接下来要求选择时间:
Select your time zone from the following list:
1)Western Russia 6)Phillipines,hongkong,Eastern China ,Taiwan
2)India 7)Japan
3)Pakistan 8)Korea
9)Thailand 9)Unlisted time zone
5)Singapore 10)Previous menu
Enter the nunber for your tiiiiiime zone(1-10),then press [Return] 键入6,回车继续
系统会询问选择是否正确:
Is this correct ?
Press [y] for yes or [n] for no .then press [Return]
键入y,回车
18.屏幕显示:
The current system time is --------------
Is this correct?
Press [y] for yes or [n] for no .then press [Return]
看系统的时间是否正确,如果不需要修改,键入y,回车
19.系统询问是否想设root的密码:
Do you want to set the root password at this time?
Press [y] for yes or [n] for no .then press [Return]