108-0906-001;中文规格书,Datasheet资料

CAUTION: Before inserting the cells into the holder, two sets of rubber feet must be applied to the correct places on the bottom of the PCB, following the steps below. Aside from applying the rubber feet and installing the cells into the holders, the PCB itself comes fully assembled and tested. Lithium cells come pre-charged (to some extent), so treat them carefully—they already contain a significant amount of energy. Handle with care and do not short the terminals! Step 1: Turn the PCB over so that it’s oriented as shown in Figure 1 below. Figure 1
Web Site: Forums: Sales: sales@ Technical: support@
Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
Features PCB-mounted cell holders with on-board charging circuitry Multiple power input/output options On-board output fuse protection Nominal 7.4 VDC output; 8.2 VDC maximum Standard 3” x 4” PCB footprint integrates well with the Board of Education

8SpecificationsModel Input SupplyInput Supply :LCS-10/LHS-1120VAC, 50/60 HzLCS-20/LHS-2240VAC, 50/60 HzLCS-3024VAC, 50/60 Hz.Maximum Allowable Supply Voltage Variation : ± 10%Maximum Power Consumption : 3 WattsDetectable Range : Up to 100,000 ohms (LCS); Up to 3,000,000 ohms (LHS)Adjustable Range : 1,000 to 100,000 ohms (LCS); 1,000 to 3,000,000 ohms (LHS)Operating Point Differential : 3% (Typical)Signal or Probe Voltage : 24VACMaximum Signal or Probe Current : 10MAOutline and Mounting Connection DiagramsModels LCS/LHS is a forward mode control. The control relay is energized when liquid rises to contact the “H” probe. The control relay is pulled in and remains energized until liquid drops below the “L” probe. Sensitivity is adjustable.Typical Curtis Model NumberModel (Also refer to “Specifications” above)Contactor (add “C” if desired)Enclosure – specify only if necessary –N3-NEMA 3, N3C–NEMA 3/Contactor, N4 – NEMA 4 JICThe composite number above reads as an LCS amplifier for 240VAC supply, without enclosure and without contactor.For further information on catalog listed controls contact your area Curtis representative or Curtis distributor.For custom design or modification contact your area Curtis representative or the factory direct.Ordering InformationShort Circuit Probe Current : 10MAControl Relay : Plug-in type with dust coverProbe Contacts : Internally Connected for Holding CircuitLoad Contacts : LCS – SPDT, 1/4 HP, 10 amp Non-inductive, 120VAC 1/3 HP at 240 VACLHS – SPDT, 1/6 HP, 10 amp Non-inductive, 120VAC 1/3 HP at 240VACAuxiliary Contactor: DPST-NO-DB, rated 1 HP at 120VAC, 2 HP at 240VAC Ambient Operating Temperature : +32° F to +140° FStandard Termination : Barrier-type terminal blocks accepting wire up to No.12AWG. Auxiliary contactor has combination screw/double .250” quick-connects Mounting Style : FlangeLCS-20- -Models LCS/LHSTwo sensitivity ranges fordetection up to 3,000,000 ohmsFeaturess Low cost Model LCS for Standard Applications up to 100,000 ohms s High-Sensitivity Model LHS for Special Applications from 100,000 to3,000,000 ohmss Solid-State Amplifier with Potentiometer for Signal SensitivityAdjustments Positive ON/OFF Operation Eliminates Relay Chatters Circuit Limits Short Circuit Probe Current to 10MA/24VAC s Holding Circuit for Differential Levels, or Manual Resets Pre-Wired Auxiliary Contactor Available for Handling Heavy Loadsand Motor Ratings Exceeding Capacity of Plug-In RelayCurtis ®liquid level controls with/分销商库存信息: CURTIS-INDUSTRIES LCS-10。

This document was generated on 08/09/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19193-0089Status:ActiveOverview:Ring Tongue - Spade TerminalsDescription:VersaKrimp™ Ring Tongue Terminal for 14-16 AWG WireDocuments:Drawing (PDF)Product Specification PS-19902-013 (PDF)Product Specification PS-19902-011 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR18689ULE32244GeneralProduct Family Ring and Spade Terminals Series19193Crimp Quality Equipment Yes Mil-Spec N/AOverviewRing Tongue - Spade Terminals Product Name VersaKrimp™Type RingUPC800755049244PhysicalBarrel Type Closed - Brazed InsulationNone Material - Plating Mating Tin Net Weight0.780/g Packaging Type Bag Stud Size8 (M4)Wire Size AWG 14, 16Wire Size mm²1.30 -2.00Material InfoOld Part NumberBB-339-08Reference - Drawing NumbersProduct Specification PS-19902-011, PS-19902-013Sales DrawingBBCD30101Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHCContains SVHC: No Low-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19193SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Hand Crimp Tool 0640030100Crimp Head for the AT-200™ Pneumatic Hand Tool0640070100This document was generated on 08/09/2012PLEASE CHECK FOR LATEST PART INFORMATION/分销商库存信息: MOLEX 0191930089。

Applications
• Sensor Circuitry • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (gas, oil, electric and water) • Medical Equipment-Patient/Equipment Isolation • Security • Aerospace • Industrial Controls
RoHS
2002/95/EC
DS-LCB710-R01
/
e3
Switching Characteristics of Normally Closed Devices
Form-B
IF ILOAD
10% toff
90% ton

1
Absolute Maximum Ratings @ 25ºC
Typical LED Forward Voltage Drop (N=50, TA=25ºC)
30
25
20
15
10
5
0 1.220 1.225 1.230 1.235 1.240 1.245 1.250 LED Forward Voltage (V)
Device Count (N)
PERFORMANCE DATA*
Ordering Information
Part # LCB710 LCB710S LCB710STR
Description 6-Lead DIP (50/Tube) 6-Lead Surface Mount (50/Tube) 6-Lead Surface Mount (1000/Reel)