SUNX LX_101传感器设置方法

色标传感器调整方法

色标传感器是一种用于检测颜色的传感器，它在工业自动化领域中起着非常重要的作用。正确调整色标传感器可以保证生产线的正常运行，提高生产效率和产品质量。下面将介绍色标传感器的调整方法，希望能对大家有所帮助。

首先，进行基本的连接。将色标传感器连接到相应的控制系统或PLC上，确保连接正确无误。接下来，打开控制系统或PLC的相应软件，进入色标传感器的调整界面。

其次，进行零点校准。在调整界面中，找到零点校准的选项，按照提示进行操作。通常情况下，零点校准是将传感器放置在没有颜色的白色表面上，进行校准，确保传感器可以正确识别白色。

接着，进行灵敏度调整。在调整界面中，找到灵敏度调整的选项，按照提示进行操作。灵敏度调整是根据实际需要，调整传感器对颜色的识别灵敏度，以确保能够准确、稳定地检测到所需的颜色。

然后，进行颜色学习。在调整界面中，找到颜色学习的选项，按照提示进行操作。颜色学习是让传感器学习所需检测的颜色，通常情况下，将所需的颜色样本放置在传感器前方，进行学习，确保传感器可以准确地识别所需的颜色。

最后，进行实时监测。在调整界面中，找到实时监测的选项，按照提示进行操作。实时监测是将传感器放置在实际工作环境中，进行监测，确保传感器可以稳定、准确地工作。

通过以上的调整方法，可以有效地调整色标传感器，确保其可以准确、稳定地检测所需的颜色。在实际操作中，还需要根据具体的情况进行调整，以达到最佳的效果。

总之，正确调整色标传感器对于工业自动化生产线的正常运行非常重要。希望以上介绍的调整方法能够帮助大家更好地使用色标传感器，提高生产效率和产品质量。祝大家工作顺利！

如何设定超声波传感器

一, 设定超声波传感器模式

注：我们目前设备上的超声波传感器的状态都需要设定成常闭模式（NC)。

要设定正确的模式，请按以下步骤进行：

1，在设备通电的情况下，断开传感器的电源（可以是旋插在传感器后面的插头，或者是接到控制板上的插座）。

2，接上插头，恢复传感器电源。

3，以下步骤需要在5分钟内完成，否则需要重新执行步骤1和2。

4，长按住（不要放）传感器上的黄色学习按钮，这时红色和绿色led灯都会亮（不用管一开始绿色灯会先闪烁）。继续按住直到只有红灯闪烁，然后松开学习按钮。

５，松开学习按钮后，现在应该只有红灯在亮。如果红灯不能保持继续亮着的话，重复第４步。

６，按住（不放）学习按钮，红灯和绿灯都会亮。

７，然后松开学习按钮，红灯和绿灯都会熄灭。这样的话，这个传感器就被设定成常闭模式了。

二，设定超声波传感器灵敏度

注：最好的灵敏度是传感器只能感应在传送皮带上５毫米之内的硅片，一般来说，只要不超过皮带上方２０毫米都没有问题。

1，在设备通电的情况下，断开传感器的电源（可以是旋插在传感器后面的插头，或者是接到控制板上的插座）。

2，接上插头，恢复传感器电源。

3，以下步骤需要在5分钟内完成，否则需要重新执行步骤1和2。

4, 长按住（不要放）传感器上的黄色学习按钮，直到绿色灯闪烁。 5， 松开学习按钮，此时绿色灯应该还在闪烁。

6， 在传感器上方的皮带上面大约5毫米的高度用硅片挡住。

7， 按住学习按钮，一开始绿色灯会亮。保持按住按钮不放，直到红色和绿色灯都亮了，并且保持不灭。

8， 然后松开学习按钮。

9， 这样灵敏度就调节好了。可以拿个硅片在确认一下是否绿色灯会在感应到硅片就亮，拿走硅片绿灯马上灭掉。

三，几点说明

1，注意灯的亮和闪烁是两个不同的状态。

2，不需要开关整个设备进行传感器调节。事实上是设备一直处于通电状态，通断电的只有需要设定的传感器，即通过插拔其上面的电源线（也即信号线）来进行整个过程。

FLCN-101

U Calls Immediate Attention to Alarm ConditionsU High Intensity Strobe Light Reduces Operator ErrorU Adjustable Time Delay RelayU Controls Pumps, Valves and AlarmsU LED Displays Switch, Sensor and Relay Status

OMEGA’s flow alert calls attention to alarm conditions. For operator alert to low flow conditions, the flow alert offers an excellent solution to this problem. An amber lens distributes the high intensity strobe light in a pattern which calls immediate attention to alarm conditions. The visual alert combined with a controller makes it both cost effective and easy to install.Flow Alert Single SenSor Controller

FLCN-101 shown larger than actual size.

SPECIFICATIONSVoltage Input: Selectable, 120 or 240 Vac, 50 to 60 HzMaximum Consumption: 5 wattsLighting Element: High intensity lampBrightness: Greater than 50,000 CPRelay Output: Isolated and sealed single pole double throw (SPDT) relay, Form CSwitching Mode: Selectable, NO or NC statesMaximum Relay Switching Voltage: 120 Vdc or 240 VacMaimum Switched Current: 10 ampsTime Delay: Adjustable from 0.15 to 60 secondsStrobe Type: XenotubeStrobe Flash: 1 per secondMaximum Temp. Rating: 70°C (158°F)Sensor Voltage Supply: 13.5 Vdc @100 mAMounting Connection: 3⁄4 NPTConduit Connection: 1⁄2 NPTEnclosure Rating: NEMA-4X (IP65)Enclosure Material: Polypropylene (PP), flame retardantDimensions: 7.1 D x 16.2 cm H (2.8 x 6.4") x 3⁄4 NPT

HF/50/144MHz ALLMODE TRANSCEIVER

Large, Multi-function LCD––––––––––––––––––The large multi-function LCD displays fre-quency, 9-character channel name, chan-nel number, multi functional meter(includes S-meter, RF output, SWR andALC level) and other operating status. Thedot-matrix portion of the LCD shows thefollowing items:• Channel name • Function key assignment • Band Scope • RTTYde-coder screen • Memory keyer contents • Graphical SWR scale RTTYDemodulator and Decoder––––––––––––––The built-in RTTYdemodulator and de-coder reads baudot RTTYsignals on thescreen without turning on your PC or othergear. The RTTYtuning indicator helps crit-ical tuning. The Twin Peak filter removesinterfering QRM giving you a more accu-rate decoded message.Ample CW Functions––––––––––––––––––––––Multi function electronic keyer, variable dot/dash ratio (2.8:1 to 4.5:1) andkey speed (6-60 WPM), paddle polarity, bug key etc. CW pitch is ad-justable (300 to 900Hz). Full break-in capability. Double key jacks – oneeach for front and rear panel.Memory Keyer––––––––––––––––––––––––––––4 channel memory keyer stores up to 50 characters with serial contest numberauto-counter, morse cut number and auto repeat function. In addition, a usersupplied external keypad* controls the memory keyer from your finger tips.* Not supplied by Icom.Built-in Antenna Tuner––––––––––––––––––––––The internal antenna tuner matches the HF and 50MHz bands automati-cally. After operating on a band for the first time, the tuner memorizes theselected antenna and preset point providing for very high speed tuning. 2antenna connectors for HF and 50MHz bands and 1 for 144MHz band isequipped on the IC-746PRO.SSB/CW Synchronous Tuning––––––––––––––––You no longer have to worry about losing a CW signal while tuning withSSB mode. With the SSB/CW synchronous tuning, the frequency auto-matically shifts when you change modes. Voice Squelch Control (VSC) Function––––––––––The Voice Squelch Control function opens the squelch only when receiv-ing a modulated voice signal. Other Outstanding Features––––––––––––––––• Triple band stacking register • 2 types of preamplifier (Regular and Hi-gain) for HF and 50MHz bands, 1 for 144MHz band • 20dB RF attenuator• Level adjustable noise blanker (101 steps) • BPF function below 500Hzband width in SSB mode • 1/4 speed dial tuning function for SSB-data,CW and RTTYmodes • 108 selectable DTCS and 50 selectable CTCSSwith encoder/decoder • 1750Hz tone encoder • Optional high stabilitycrystal unit, CR-338 • Up to 10 memo-pads temporarily store frequenciesand modes • Quick split function with split lock function • ±9.99kHz RITand ∂TX • Band edge beep • CI-V capability for PC control • VOX • Pro-gram, memory, select memory and ∂F scans • IF transmit audio monitor(SSB mode only; AF transmit audio monitor for the other modes) • 102memory channels • 9600bps data terminal • AH-4 control circuits • AutoTS function •Optional voice synthesizer unit, UT-102 announces the op-erating frequency, mode and S-meter level • 1Hz tuning and indicationDigital Twin PBT––––––––––––––––––––––––––Only Icom brings you Twin Passband tuning! Tailoryour IF passband with the Twin PBTby electronicallyshifting the upper and lower IF passbands. Dependingon the use of the concentric knobs, you can either nar-row the IF passband, or shift the entire passband toeliminate interfering signals.Manual Notch Filter––––––––––––––––––––––Interference management is not a prob-lem with the Manual Notch filter. With it’sincredible 70dB attenuation, the manualnotch can eliminate a wide variety ofQRM. The Automatic Notch Filter cantrack two or more interfering signals likeHeterodynes and “Key uppers”!Digital Noise Reduction––––––––––––––––––––By digitally manipulating the incoming signal, the DSPis able to reducevarious types of noise and enhances the receive signal components. Pro-viding an outstanding signal to noise ratio to give clean, clear audio.