DC450操作与维护手册

Quarter Master Chief Series 92 ActuatorInstallation, Operationand Maintenance ManualTable of ContentsSeries 92 Electric Actuator Introduction (3)Description (3)Electrical Requirement (3)Installation (4)Electrical (4)Type 21 Ball Valve (4)Type 23 Ball Valve (3-way) (5)Type 57 / 57L Butterfly Valves (5)Actuator Mounting Dimensions (6)Operation (7)Manual Override Operation (7)Setting Limit Switches (7)Options (8)Single Limit Switch (8)Double Limit Switch (8)Heater and Thermostat (8)Mechanical Brake (9)Feedback Potentiometer (9)Series 92 Options Codes for Serial # Tags (10)Troubleshooting (10)Maintenance (12)ATEX Requirements (12)Spare Parts (13)Series 92 Electric Actuator IntroductionDescriptionThe Series 92 electric actuators feature a reversing,capacitor run motor, with a permanently lubricated gear train, and hardened steel spur gears. These actuators are equipped with integral thermal overload protection (AC models) with automatic reset, independently adjustable limit switches, declutchable manual override, beacon position indication, baked powder epoxy coating with stainless steel trim, ISO bolt circle, and 2 (two) ½” NPT conduit entries.Standard models are offered in 115 VAC, feature a combination enclosure of Nema-4X, 7 & 9, and, provide up to 2000 in-lbs. of output torque.Various options are available such as operating voltages, additional limit switches, heater and thermostat, feedback potentiometers, etc.Please see page 8 regarding these options.Electrical RequirementWARNING: Do not open actuator cover while circuits are energized.CAUTION: Proper voltage must be supplied to actuator or damage will result.CAUTION: If 115vac & 220vac models are PLC driven, output contacts of PLC should be rated at a minimum of 1.5 times required input voltage of actuatorNOTE: To conform to various electrical codes, a green grounding screw has been provided (on the baseplate) inside of actuator.Terminal Strip Wiring: 75° C Copper Supply Wires up to #14 AWG, wired as per the attached diagrams or the wiring diagram affixed inside of actuator cover. Control Wiring shall be insulated with conductors rated 105° C, 300 V minimum.Torque Terminal Strip Wiring to 5 in-lbs.115 Vac 230 Vac 12 Vdc 24 Vdc 12 Vac 24 Vac Cycle Timeper 90 Model Torque Amp Duty Amp Duty Amp Duty Amp Duty Amp Duty Amp DutyDegrees (in/lbs) Draw Cycle Draw Cycle Draw Cycle Draw Cycle Draw Cycle Draw Cycle (seconds) S92 400 0.5 100% 0.4 100% 2.075% 4.075% 2.075% 3.0 75% 10A92 700 0.8 75% 0.6 75% 2.075% 4.075% 2.075% 3.0 75% 10B92 1100 0.5 100% 0.4 100% 2.075% 4.075% 2.075% 3.0 75% 25C92 2000 1.0 50% 0.6 50% 2.075% 4.075% 2.075% 3.0 75% 25 NOTE: Amp rating is considered locked rotor.Duty cycles are for ambient temperature (73°F)InstallationElectricalReference Drawing #289S92Models S-92, A92, & B921A. To gain access to terminal strip (Part #24) it is necessary to remove manual override knob (Part #18) by loosening slotted setscrew (Part #39). Remove 2 cover screws and cover; the remaining 6 cover screws are packaged inside the actuator. Torque cover/base screws to 120 in-lbs.Note: Failure to properly tighten cover/base flange fasteners to 120 in/lbs may compromise the certified safety factors of the actuator.Model C921B. To gain access to terminal strip it is necessary to remove manual override hand wheel (Part #18A) by loosening slotted setscrew (Part #39). Remove cam (Part #51) by loosening 2 set screws (Part #52). Remove 2 cover screws and cover; the remaining 6 cover screws are packaged inside the actuator.Torque cover/base screws to 120 in-lbs.All Models2. Make electrical connections to terminal strip as shown on wiring schematiclocated inside the cover (per various electrical codes there is a green screw on the actuator base plate for grounding purposes). Terminals are suitable for up to #14 AWG wire. All units are completely calibrated prior to shipment, and no internal adjustments should be required.3. For United States units, Install 1/2" NPT conduit fitting(s) to actuator base.For ATEX Certified European Union units, Install M20 x 1.5 conduit fitting(s) to actuator base.Note: Proper conduit fitting must be used to maintain enclosure rating and not compromise the certified safety factors of the actuator(weatherproof, explosion proof or combination weather proof/explosion proof). NOTE: We recommend sealing conduit openings on units installed outdoors or exposed to large temperature swings (15ºF or more).We also recommend the Heater and Thermostat option in these applications. 4. Replace actuator (gasket if removed) cover, and install 8 cap screws suppliedand tighten securely to 120 in/lbs. For outdoor or wet locations it isrecommended prior to replacing the cover that the top shaft seal be cleaned and coated with silicone grease. Also clean shaft and lightly coat seal area of shaft with silicone grease. Unit is now ready for operation.Type 21 Ball ValvePosition the valve and the actuator to corresponding positions (either OPEN or CLOSED). The flats on the actuator shaft extension indicate valve positionType 21 Ball Valves (See Drawing #0107BV sizes ½” – 2”)Install mounting bracket #3 to actuator #2 using bolts #8 and washers #9. Insert coupling #4 on stem of valve #1 and then bolt valve #1 to mounting bracket #3 using bolts #5, nuts #7, and washers #6.Note: All bolts should be snug and not excessively over tightened.Type 21 Ball Valves (See Drawing #0113BV sizes 2-1/2” - 4")Install mounting bracket #3 to actuator #2 using bolts #8 and washers #9. Insert coupling #4 on stem of valve #1 and then bolt valve #1 to mounting bracket #3 using bolts #5, nuts #7, and washers #6.Note: All bolts should be snug and not excessively over tightened.Type 23 Ball Valve (3-way)Position the valve and the actuator to corresponding positions (either OPEN or CLOSED). The flats on the actuator shaft extension indicate valve positionType 23 Ball Valves (3-way): (See Drawing #0130BV, sizes ½” - 4”)Install mounting bracket #3 to actuator #2 using bolts #8 and washers#9. Insert coupling #4 on stem of valve #1 and then bolt valve #1 tomounting bracket #3 using bolts #5, nuts #7, and washers #6.Type 57 / 57L Butterfly ValvesCAUTION: If valve is in line, system must be shut down and have no line pressure before removing throttle plate and retaining washer.Position the valve and the actuator to corresponding positions (either OPEN or CLOSED). The flats on the actuator shaft extension indicate valve position Butterfly Valves (See Drawing # 0200BF57 sizes 1-1/2” - 6”)No specially machined stem or valve body drilling required. Remove handle (remove handle cap and hex head bolt) to expose throttle plate screws. Remove throttle plate and retaining washer to expose existing bolt pattern.Mount bracket #3 to actuator #2 with bolts #8 and washers #9 and tighten evenly. Insert coupling #4 into actuator #2.Install valve #1 onto mounting bracket #3 and align stem of valve to engage with coupling. (Line scribed on top of stem indicates disc orientation). Install bolts #5, washers #6 and nuts #7 and tighten evenly. Flats on actuator shaft indicate valve position. (Disc Orientation)Butterfly Valves (See Drawing #0168BF57 8” size)No specially machined stem or valve body drilling required. Remove gear operator by removing 4 thru bolts in body of valve to gear operator and lift off. Mount bracket #2 to actuator #10 using bolts #7 and washers #8. Insert actuator shaft adapter #9 into actuator #10. Install valve #1 to mounting bracket #2 and align stem of valve to engage with coupling. (Line scribed on top of stem indicates disc orientation). Install bolts #3, washers #4 & #5 and nuts #6 and tighten evenly. Flats on actuator shaft indicate valve position. (Disc Orientation) CAUTION: If mounted unit is installed other than straight up, the actuator should be supported independently to prevent side loading and loosening up ofOperationManual Override OperationReference Drawing #289S92Models S-92, A92, & B92Pull up the declutching knob (Part #18) and apply a 5/8" open end wrench to exposed flats and rotate within labeled limits as indicated by arrows.To re-engage simply rotate actuator shaft in the opposite direction until declutching knob drops back down into position.Model C92Push down on hand wheel (Part #18A) and rotate within labeled limits.To re-engage simply rotate actuator hand wheel until it moves up and re-engages.CAUTION: The manual override should only be used when there is no power applied to actuator. When power is restored the actuator will automatically resume normal operation.Setting Limit SwitchesReference Drawing #289S92Open Travel Limit Switch (Top Switch Part #25):Using declutchable manual override, move the valve into a full open position. Then loosen set screws on top cam (Part #40) and rotate cam (CCW) into limit switch arm until a click is heard, this designates the switch circuit has opened and defines a full open position. Tighten 2 set screws (Part #40) on cam.Close Travel Limit Switch (Bottom Switch Part #25):Using declutchable manual override, move the valve to a full closed position, loosen set screws on bottom cam (Part #40) and rotate cam (CW) into limit switch arm until a click is heard, this designates the switch circuit has opened and defines a full closed position. Tighten 2 set screws (Part #40) on cam.Manually position valve to midstroke. Reapply power to actuator and drive to open or closed position. Actuator motor will run. The shaft will not turn until drivepins (Part #7) reseat in drive gear. This could take up to 25 seconds.OptionsModels S92, A92, B92, C92Single Limit SwitchInstall additional limit switch on posts on opposite side of standard limit switches using screws provided.Wiring for switch is as follows:Pink = Common to Terminal #6Purple = NC to Terminal #7Blue = NO to Terminal #8Cam must be set so that this switch is tripped just ahead of Closed limit switch. Wire tie loose wiring and check operation before installing cover.Double Limit SwitchInstallation and wiring is the same as for the single limit switch, with the additionof wiring of the second switch as follows:Brown = Common to Terminal #9Green = NC to Ternimal #10Orange = NO to Terminal #11Cam must be set so that this switch is tripped just ahead of Open limit switch. Wire tie loose wiring and check operation before installing cover.Heater and ThermostatModels S92 & A92Install Heater into threaded hole located between actuator base gasket andmotor module.Wiring is as follows:Heater lead = Terminal #12Thermostat lead = Terminal #13Wire tie loose wiring and check operation before installing cover.Models B92 & C92Install Heater into threaded hole located between actuator shaft and motor module.Wiring is as follows:Heater lead = Terminal #12Thermostat lead = Terminal #13Wire tie loose wiring and check operation before installing cover.Mechanical BrakeLoosen two (2) motor screws diagonally from each other and install bracket with tabs facing upward. Tighten screwsInstall hexagonal adapter over armature shaft and tighten set screws.NOTE: The adapter should be resting on the step of the armature shaft.Install brake assembly onto hexagonal adapter making sure that the brake assembly is sitting flush on the bracket. Tighten with supplied screws.Remove motor leads “A” & “B” from capacitor and install “piggy back connectors to capacitor, the re-install motor leads to their original locations.Connect brake leads to piggy back connectors on capacitor (orientation does not matter)Wire tie loose wiring and check operation before installing cover.Feedback PotentiometerUsing 4-40 x 3/8 hardware, install potentiometer and bracket on standoffs by limit switches, with potentiometer gear facing output shaft.Install drive gear face down over output shaft.Wiring for potentiometer as follows:#1 on potentiometer (black) #14 on terminal strip.#2 on potentiometer (white) #15 on terminal strip.#3 on potentiometer (red) #16 on terminal strip.Using multimeter set at 2k ohms, calibrate potentiometer with leads from meter connected to terminals #15 and #16. With actuator in closed position multimeter should read between 95 and 100 ohms.Rotate actuator 90 degrees (open position).Connect leads from multimeter to terminal #14 and #15; multimeter should read 95 to 100 ohms.If necessary adjust open limit switch cam so that multimeter will read 95-100 ohms.Series 92 Options Codes for Serial # TagsExample 1: S92HTP XWJHeater & thermostat and feedback potentiometer installed.Example 2: A92BRM1XWJMechanical brake and 1 extra limit switch installed.Troubleshooting WARNING: Do not open actuator cover while circuits are energized.Q: What if there is no output, but the motor runs?A: Manual override possibly engaged.When the manual override is engaged, the motor will run, but no output will be observed until the manual override re-engages with the output shaft.A: Valve stem broken. When the valve stem is broken, there will not be a change in fluid movement, making it seem as if the actuator has no output..Q: What if valve does not cycle?A: No power source to actuator. Check for power.A: Power source disconnected. Check for broken wire, loose connection or no connection as per appropriate wiring diagram.A: Low or wrong power source. Check for proper voltage.A: Mechanical Brake jammed or misaligned. Check alignment of brake assembly.This could occur during installation when someone would rest their hand on the Mechanical Brake to steady themselves. M1 1 extra limit switchM2 2 extra limit switches HT Heater & thermostat P Feedback potentiometer DP Dual feedback potentiometers C1 4-20 mA Positioner C3 4-20mA Output Transmitter BR Mechanical brake L2 2-Position Indicating Lights CO Center offCL Cycle length control 2W 2-wire control FS Failsafe Battery Pak A4 4-12mA Input Signal Positioner B12 Split Range Positioner ASI AS-I Bus Network CardQ: What if there is water and/or moisture inside of the unit?A: Conduit fitting installed improperly. Re-install correctly.A: Cover and/or base seal damaged. Replace damaged seal(s).A: Base gasket damaged or installed improperly. Check gasket and replace if necessary.A: Temperature swings of more than 15 degrees F. Install heater and thermostat to eliminate condensation.When these temperature swings occur, the unit will “sweat” on the inside causing internal corrosion unless the actuator is equipped with a heater and thermostat to keep a constant temperature inside of the housing.A: Unit has been submerged. Raise unit above liquid level.An actuator that is to be submerged MUST meet NEMA 6 for the proper protection of the actuator and the elimination of a potential hazard. We do not recommend submerging the Series 92 Actuator as the electrical rating does not meet NEMA 6.Q: What if unit is oscillating?A: Valve torque exceeds output torque of actuator. Check for chemical compatibility of valve, and flange torque.Q: What if thermal overload frequently cuts out motor?A: Frequency of operation exceeds duty cycle rating. Check cycling period.A: Unit is oscillating. Refer to above.Q: What if motor hums and no output is observed?A: Foreign material caught in valve. Remove material and inspect valve for damaged and/or worn parts. Replace parts as necessary.A: Unit wired incorrectly (simultaneously powering open and closed). Check wiring as per appropriate wiring diagram.A: Capacitor worn. Replace.Q: What if actuator “over-shoots” limit switches without stopping?A: Actuator wired in parallel to each other. Please note that each actuator requires it’s own set of switch contacts.MaintenanceDisconnect power!WARNING: Do not open actuator cover while circuits are energized. ArrayCAUTION: It is imperative for reducing the chance of electrical shock, and to prevent ignition of hazardous atmospheres that youDisconnect powerbefore any maintenance or repairs are performed.Series 92 actuators are virtually maintenance free. We do however, recommend that periodic checks are made to ensure that all fasteners are tight and properly torqued to extend the life of the actuator and valve.Series 92 Actuators are manufactured with factory lubricated grease in the gear case and gearbox. In most cases, this lubricant should never have to be replenished, however if deemed necessary, we recommend using Aeroshell Grease #33 MS, mfg. by Shell Oil Co.Consult our technical department before replenishing lubricant.For outdoor or wet locations keep top and bottom seals coated with a silicone based grease.ATEX RequirementsATEX Standard EEx d IIB Directive II 2 G Certified UnitsService/Maintenance/Inspection RequirementsAbove directive for hazardous location service electric actuators, for use throughout the European Union.All electric actuators are to be used for remote operation of a valve to open or closed positions. Any other uses are not approved by Asahi/America, Inc.Every 250,000 cycles or 10 years whichever comes first, the actuator must be removed from service and sent back to Asahi/America, Inc. for inspection of wear of bearings as they relate to joints and gaps in accordance with above directive. Any units not within normal tolerances, will need to be re-built or replaced at theusers expense.Spare PartsReference Drawing #289S92We recommend that the following be kept on hand as spare parts.1 --- Limit Switch (Part #25)1 --- Capacitor (Part #27 or #28)NOTE: When ordering replacement motor parts and/or options specify model # and voltage.Attachments:9 drawings: 0043EL, 0044EL, 0042EL, 0107BV, 0113BV,0130BV, 0168BF57, 0200BF57, 289S92。

Features
In the world of high performance bass amps, Ampeg amplifiers stand alone. In true Ampeg tradition, the SVT450H offers you more power, performance and flexibility than any other bass amplifier in its class. The outstanding features of your new amplifier, features which set it apart from the competition, are listed below.
User’s Guide for the
SVT450H
Bass Amplifier
SVT450H Bass Amplifier
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Some Suggested Settings . . . . . . . . . . . . . . . . . . . . . . . . .6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Technical Specifications . . . . . . . . . . . . . . . . . . .back cover

450 CONFIGURABLE CONTROLLERMain applications •Packaging machines •Packing machines• Labelers•Food processing lines andmachines •Laboratory machines and ovens •Electrical heaters for industrial heating Main features•Universal input configurable from the faceplate•Accuracy better than 0,2% f.s.at nominal condition•Control output: relay or logic with Heat or Cool function•1 alarm with configurable function •Self-tuning, Auto-tuning, Soft-start, Man/Auto function •Possibility to configure the unit byserial linePROFILEThe series 450 temperature controller, measuring 48x48mm (1/16 DIN), offers simplicity of use and high quality of con-trol.The input from temperature sensors is “universal” and configurable with type J, K, R, S, T, B, E, N thermocouples and with 3-wire Rt100 resistance thermome-ters.The user interface has a complete double display with green LEDs, 4 keys, and two red LEDs to signal active outputs.The Lexan® membrane on the front panel guarantees an IP65 protection level for these products.The controller outputs, freely configurable as control output and alarm output, are available in a 5A/250VAC relay version or in a logic signal version to drive solid state relays.The input signal read speed (120msec) and the tested PID control algorithm with selftuning and autotuning parameter functions guarantee accurate and stable control even for rapid and discontinuous heating systems.Series 450 models are factory-configured to satisfy most industrial heating applica-tions (input for probe J, hot PID setting, 10 second cycle time) and can always bemodified from keyboard and from PC witha few parameters grouped on intuitivemenus.A programming kit for PC is available,consisting of a cable and a user-friendlyprogram for Windows with Wizard pages,oscilloscope for process analysis, savingof parameter recipes, and ability to resetfactory parameters. A settable softwareprotection code (password-protected) letsyou limit access to internal parameters tovarious levels, up to total protection.TECHNICAL DATAI nputsAccuracy 0,2% f.s. ±1digit.Sampling time 120msec.TC - ThermocoupleJ(Fe-CuNi) 0...1000°C / 32...1832°FK(NiCr-Ni) 0...1300°C / 32...2372°FR(Pt13Rh-Pt) 0...1750°C / 32...3182°FS(Pt10Rh-Pt) 0...1750°C / 32...3182°FT(Cu-CuNi) -200...400°C / -328...752°FB(Pt30Rh-Pt6Rh) 44...1800°C / 111...3272°FE(NiCr-CuNi) -100...750°C / -148...1382°FN(NiCrSi-NiSi) 0...1300°C / 32...2372°FRTD 3-wiresPt100 -200...600°C / -328...1112°FO utputsOutputs fully configurable for control andsingle alarm function.RelayWith rating: 5A/250 Va.c., cos j=1(order code: R)Logic12V (6V min 20mA)(order code D)p Ower s upply(Standard) 100...240 V a.c. ±10% (Optional) 11...27 V a.c./d.c. ±10% 50/60Hz, max. 10VAA mbIent C OndItIOnWorking temperature range: 0...50°C Storage temperature range: -20...70°C Humidity: 20...85%Ur non condensing C OntrOlOn/Off, P, PD, PID either for heating or cooling, with parameters configurable from the faceplate.Cooling setpoint relative to heating setpoint.• Manual reset -999...999 digit• Power reset -100,0...100,0%• Cycle time 0...200sec• Soft-start 0,0...500,0 minFor each action:• Proportional band 0,0...999,9% f.s.• Integral time 0,0...99,99 min• Derivative time 0,0...99,99 min• Max power limit 0,0...100,0%A lArms• 1 alarm with setpoint settable at absolu-te, deviation, symmetrical deviation value compared to setpoint with direct or inver-se function.• The alarm point may be set anywhere within the configured scale.• LBA (Loop Break Alarm) function alarm • Alarm Hysteresis configurablew eIght210g complete versionFACEPLATE DESCRIPTIONL38888 450FCDE FCONNECTION DIAGRAMGEFRAN spa reserves the right to make any kind of design or functional modification at any moment without prior notice.GEFRAN spa via Sebina, 74 - 25050 Provaglio d’Iseo (BS)Tel. 03098881 - fax 0309839063 - Internet: DTS_450_10-2016_ENG。

.002-**x HDD002-770 作业模板处理-HD 满003-**x IPS-ESS 通讯003-318 IIT 软件故障003-319 IIT 视频驱动程序检测故障003-320 IISS-ESS 通讯故障1003-321 IISS-ESS 通讯故障2003-322 IISS-ESS 通讯故障3003-323 IISS-ESS 通讯故障4003-324 IISS-ESS 通讯故障5003-325 IISS-ESS 通讯故障6003-326 IISS-ESS 通讯故障7003-327 IISS-ESS 通讯故障8003-328 IISS-ESS 通讯故障9003-329 IISS-ESS 通讯故障10003-330 IISS-ESS 通讯故障11003-331 IISS-ESS 通讯故障12003-332 IISS-ESS 通讯故障13003-333 IISS-ESS 通讯故障14003-334 IISS-ESS 通讯故障15003-335 IISS-ESS 通讯故障16003-336 IISS-ESS 通讯故障17003-337 IISS-ESS 通讯故障18003-338 IISS-ESS 通讯故障19003-339 IISS-ESS 通讯故障20003-340 IISS-ESS 通讯故障21003-341 IISS-ESS 通讯故障22003-342 IISS-ESS 通讯故障23003-343 IISS-ESS 通讯故障24003-345 X PIO 未锁定故障1003-346 X PIO 未锁定故障2003-750 书本双面-原稿不够003-751 PANTHER 容量低下〔扫描〕003-753 扫描不能超过300dpi003-760 扫描设置故障003-761 不正确的纸盘尺寸003-763 未发现调整表003-780 扫描图像压缩故障003-795 AMS 限制错误003-942 原稿尺寸自动检测故障003-944 图像重复计数003-945 放大倍率不适合003-946 每个方向都矛盾〔复印APS〕003-947 返回原稿计数错误003-948 返回原稿不匹配003-949 原稿不适当〔图像覆盖〕003-950 混合原稿尺寸错误003-955 原稿尺寸交换错误003-956 原稿尺寸不明错误003-957 原稿尺寸错误003-963 无APS 目标纸盘003-965 ATS/APS 无纸〔IIT 检测〕003-966 ATS/APS 无目标〔IIT〕003-970 行存储器溢出003-972 最大存储页溢出003-973 各个方向都矛盾003-974 下一原稿规格003-976 行存储器溢出〔N up〕003-977 原稿不匹配〔多重扫描〕003-980 装钉位置错误003-981 装钉尺寸错误005-**x DADF005-121 CVT 输送传感器On 卡纸005-122 CVT 单面/面1 预定位On 卡纸005-123 CVT 单面/面1 定位卡纸005-125 CVT 定位传感器Off 卡纸005-131 CVT 翻转On 卡纸005-132 CVT 翻转On 卡纸2005-134 CVT 翻转传感器Off 卡纸〔翻转器〕005-135 CVT 面2 预定位On 卡纸005-136 CVT 面2 定位On 卡纸005-139 CVT 翻转传感器Off 卡纸005-145 CVT 定位传感器Off 卡纸〔翻转器〕005-146 CVT 预定位传感器Off 卡纸RAP 005-147 CVT 预定位传感器Off 卡纸〔翻转器〕005-194 在FF混合尺寸中SS尺寸不匹配卡纸005-196 CVT 尺寸不匹配卡纸〔无混合〕005-197 制止组合尺寸卡纸005-198 太短尺寸卡纸005-199 太长尺寸卡纸005-280 DADF EEPROM 故障005-283 DADF 高度传感器逻辑故障005-284 DADF APS 传感器故障005-285 DADF 轻推辊提升故障005-286 DADF 输出传感器故障005-302 DADF 输送器盖联锁翻开005-304 CVT 稿台联锁翻开.005-305 CVT 输送器联锁翻开〔运行〕005-307 CVT 稿台联锁在运行中翻开005-906 CVT 输送传感器静态卡纸005-907 CVT 预定位传感器静态卡纸005-908 CVT 定位传感器静态卡纸005-913 CVT 翻转传感器静态卡纸005-915 CVT APS No1 传感器静态卡纸005-916 CVT APS No2 传感器静态卡纸005-917 CVT APS No3 传感器静态卡纸005-942 DADF 中放置的原稿故障005-943 DADF 盘提升故障010-**x 定影器010-313 控制热敏电阻故障010-314 侧端热敏电阻故障010-318 热-下跌恢复故障010-320 热辊过热故障010-327 定影器On 时间故障010-398 定影器锁位故障012-**x装订器012-111 装订器H-传输入口传感器Off 卡纸012-112 装订器H-传输入口传感器On 卡纸012-121 H-传输出口传感器Off 卡纸012-126 H-传输入口传感器Off 卡纸012-151 编辑盘入口传感器Off 卡纸012-152 编辑盘入口传感器On 卡纸012-161 装订器压板卡纸012-162 H-传输出口传感器On 卡纸012-211 堆积盘故障012-212 堆积盘上限故障012-221 前对齐板原位传感器On 故障012-223 前对齐板原位传感器Off 故障012-224 后对齐板原位传感器Off 故障012-260 排出压板原位传感器On 故障012-263 后对齐板故障012-282 排出压板原位传感器Off 故障012-283 放置压板原位传感器On 故障012-284 放置压板原位传感器Off 故障012-291 装订器故障012-293 装订前角传感器On 故障012-294 装订前角传感器Off 故障012-295 装订移动传感器On 故障012-296 装订移动传感器Off 故障012-301 装订器顶盖翻开012-302 装订器前盖翻开012-303 装订器H-传输盖翻开012-901 装订器H-传输入口传感器静态卡纸012-902 H-传输出口传感器静态卡纸012-903 纸留在编辑盘入口传感器012-905 编辑盘纸传感器静态卡纸012-923 H-传输入口传感器静态卡纸B 016-**x 效劳016-210 SW 选项故障〔HDD 不存在〕016-211 SW 选项故障〔系统存储器缺乏〕016-212 SW 选项故障〔页存储器缺乏〕016-213 SW 选项故障〔打印机卡不存在〕016-214 SW 选项故障〔卡不存在〕016-215 SW 选项故障〔JPEG 板不存在〕016-311 扫描器未安装016-315 IIT 接口故障016-316 未检测到页存储器016-317 页存储器中止-标准016-318 页存储器中止-选项016-321 模块故障016-322 A 满016-450 SMB 主机名重复016-454 DNS 动态更新故障016-455 SNTP 效劳器超时016-456 SNTP 时间异步016-503 SMTP 效劳器重定向故障016-504 POP 效劳器重定向故障016-505 POP 重定向验证故障016-600 KO 验证锁定016-601 非法访问检测016-701 ART EX 存缺乏016-702 页缓冲器缺乏016-703 至无效016-704 满016-705 平安打印故障016-706 最大用户数超出016-707 样本打印故障016-708 HD 因注解/水印图象而满016-709 ART EX 命令故障016-710 延时打印故障016-711 传输尺寸限制超出016-712 PANTHER 能下低下〔I-Formatted〕016-716 TIFF 数据溢出016-718 超出PCL6 存储器016-719 超出PCL 存储器.016-720 PCL 命令故障016-721 其它错误016-722 作业被装订位置NG 删除016-728 不支持TIFF 数据016-729 TIFF 数据尺寸太大016-730 不支持ART 命令016-731 无效TIFF 数据016-732 表格未注册016-735 更新作业模板016-736 远程目录加锁错误016-737 远程加锁目录卸载错误016-746 不支持PDF 文件016-748 HD 满016-749 JCL 语法错误016-751 PDF 故障016-752 PDF 存缺乏016-753 PDF 命令不匹配016-754 PDF LZW 未安装016-755 PDF 打印被制止016-756 审计-制止效劳016-757审计-无效用户016-758 审计-制止功能016-759 审计-到达限制016-760 PS 解压缩故障016-761 FIFO 空016-762 打印语言未安装016-764 SMTP 效劳器连接故障016-765 SMTP 效劳器HDD 满016-766 SMTP 效劳器文件系统016-767 无效的地址016-768 无效的发送者地址016-769 SMTP 效劳器不支持DNS016-771 扫描数据贮藏室〔DNS 地址〕错误016-772 扫描数据贮藏室〔DNS 库〕错误016-773 无效的IP 地址016-774 HD 满-压缩转换016-775 HD 满-图像转换016-776 图像转换错误016-777 图像转换错误016-778 HD 满-扫描图像转换016-779 扫描图像转换错误016-780 HD 访问错误-图像转换016-781 扫描效劳器连接错误016-782 扫描效劳器登录错误016-783 无效的效劳器路径016-784 效劳器写错误016-785 效劳器HD 满016-786 HD 满-扫描写入错误016-787 无效的效劳器IP 地址016-788 检查浏览器故障016-789 HD 满-作业存储器016-791 文件检索故障016-792 未发现指定作业016-793 MF I/O HD 满016-798 No Trust Marking 选择016-799 PL W 打印指令故障016-981 HDD 访问错误016-982 HDD 访问错误2016-985 数据尺寸溢出〔扫描到〕021-**x021-360 EP 附件故障021-361 EP 附件各类配置错误021-732 EP 附件-效劳被禁用021-733 EP 附件-效劳受彩色模式限制021-750 用过零件请求处理故障〔EP-SV〕021-751 维护请求故障〔EP-SV〕021-770 用过零件请求处理故障〔EP-SV〕021-771 维护请求故障〔EP-DX〕021-772 EP-DX-安装/卸载故障021-941 EP-扫描效劳因禁用而暂行021-942 EP-扫描效劳因彩色模式而暂行021-943 EP-打印效劳因禁用而暂行021-944 EP-打印效劳因彩色模式而暂行021-945 EP-效劳因禁用而暂行021-946 EP-效劳因彩色模式而暂行024-**x IOT-ESS 通讯024-340 IOT-ESS 通讯故障1024-341 IOT-ESS 通讯故障2024-342 IOT-ESS 通讯故障3024-343 IOT-ESS 通讯故障4024-345 IOT-ESS 通讯故障5024-346 IOT-ESS 通讯故障6024-347 IOT-ESS 通讯故障7024-348 IOT-ESS 通讯故障8024-349 IOT-ESS 通讯故障9024-350 IOT-ESS 通讯故障10024-351 IOT-ESS 通讯故障11024-354 IOT-ESS 通讯故障14.024-356 IOT-ESS 通讯故障16024-362 页面同步非法启动024-363 页面同步非法停顿024-364 DMA 传输故障024-367 解压缩其他故障024-368 PCI 错误024-370 标志码检测故障024-371 IOT-ESS 通讯故障21024-372 IOT-ESS 通讯故障22024-373 IOT-ESS 通讯故障23024-375 IOT-ESS 通讯故障23024-746 打印请求故障—纸024-747 打印指令故障024-910 纸盘1 尺寸不匹配024-911 纸盘2 尺寸不匹配024-912 纸盘3 尺寸不匹配024-913 纸盘4 尺寸不匹配024-916 混合满堆积盘024-917 堆积盘装订超出计数024-919 面朝上盘关闭024-946 纸盘1 不在位024-947 纸盘2 不在位024-948 纸盘3 不在位024-949 纸盘4 不在位024-950 纸盘1 空024-951 纸盘2 空024-952 纸盘3 空024-953 纸盘4 空024-954 MSI 空024-958 MSI 尺寸故障024-959 纸盘1 尺寸不匹配024-960 纸盘2 尺寸不匹配024-961 纸盘3 尺寸不匹配024-962 纸盘4 尺寸不匹配024-964 装订器数超出024-965 ATS/APS 无纸〔IOT 检测〕024-966 ATS/APS 元目标错误024-967 不同宽度混合纸检测(装订器作业) 024-976 装订器装订静态NG024-977 装订器输送准备故障024-979 装订器接近空024-980 装订器堆积盘满024-982 堆积盘下平安警告024-985 MSI 输送故障024-986 打印全部确认025-**x 诊断 HDD025-596 诊断HDD 维护故障025-597 诊断HDD 初始化故障027-**x MAIL027-452 重复IP 地址027-500 SMTP 效劳器I/O 故障027-501 POP 效劳器I/O 故障027-502 POP I/O 验证故障027-700 媒体故障027-701 未找到媒体027-702 媒体数据未找到/不支持027-703 媒体读出器故障/未连接027-710 因效S/MIME 错误027-711 S/MIME 发送者证书未找到027-712 S/MIME 发送者证书无效027-713 S/MIME 被改变027-714 S/MIME 发送者假冒027-715 S/MIME 证书不被支持027-716 制止接收没有签名的027-720 未找到扩展效劳器主机027-721 未找到扩展效劳器027-722 扩展效劳器时故障027-723 扩展效劳器验证故障027-724 扩展效劳器访问故障故障027-725 扩展效劳器操作故障027-726 扩展效劳器未知状态027-727 扩展效劳器请求无效参数027-737 模板效劳器读取错误027-739 无效模板效劳器路径027-740 模板效劳器登录错误027-741 模板效劳器连接故障027-742 HD 文件系统满027-743 模板效劳器安装错误027-744 模板效劳器地址错误〔CDNS 带〕027-745 模板效劳器地址错误〔CDNS 地址〕027-746 作业模板效劳器未准备027-750 文件不适合027-751 作业模板分析错误027-752 要求的用户输入未输入027-753 作业流效劳请求制止027-796 不打印027-797 无效输出目标033-**x 控制.033-363 卡复位(重新引导)033-710 原稿不存在033-711 文档中存在非法页面033-712 系统存溢出033-713 未指定链-环033-714 扫描错误〔未指定文档〕033-715 不能启动作业033-716 无指定MAILBOX033-717 不正确口令033-718 中无文档033-719 被删除作业不能恢复033-720 文档创立故障033-721 页面创立故障033-724 接收存储器溢出033-725 HDD 空间缺乏033-726 不能打印双面033-727 不能旋转图像033-728 删除自动打印033-730 效劳恢复错误033-731 指令不一致033-732 打印作业被强制轮询删除033-733 文档号获取错误033-734 打印悬置033-735 存储器地址分配超时033-736 IFAX Off Ramp 错误033-737 卡作业删除033-738 IG 信息故障033-740 直接接收打印删除033-741 页面读取翻开超时033-742 页面读取关闭超时033-743 页面写入翻开超时033-744 页面写入关闭超时033-745 数据写入超时033-746 数据读取超时033-747 效劳不能启动033-748 效劳非法顺序033-749 卡存错误033-750 格式错误033-790 EP-DX 呼叫等待(不重拨计数) 033-791 EP-DX 呼叫等待(重拨计数) 033-792 EP-DX 呼叫停顿034-**x 通讯034-211 选项槽1 板故障034-212 选项槽1 板故障034-500 不正确拨号数据034-501 所连通道拨号错误034-502 部不可缺少参数错误034-503 部高层效劳错误034-504 储存存储器溢出034-505 工作存储器溢出034-506 不支持远程功能034-507 口令检查错误034-508 通过DTMF删除传输034-509 DTMF 非法程序错误034-510 DTMF 程序错误034-511 远程机器不能发送文件034-512 检测到无尽循环034-513 接收命令错误034-514 请求的功能不支持034-515 非法命令被接收034-519 接收数量超出034-520 效劳数量超出034-521 部I/F 错误034-522 无手动发送线路034-523 效劳被制止034-524 不能删除操作034-525 指定的链-环不存在034-526 不正确的链-环值034-527 拨号控制错误034-528 不能执行手动发送034-529 无打印的纸尺寸034-530 DTMF I/F 超时034-700 G3 节Dicep 超时034-701 软件复位034-702 无指定目标034-703 D 信道与网络连接切断034-704 ISDN D 信道数据连接错误034-705 ISDN 层1 停顿-电源ON 034-706 ISDN 层1 停顿-电源OFF 034-707 FRMR 被接收034-708 非法帧接收N〔R〕034-709 非法帧接收034-711 等待连接超时034-712 部错误〔中断〕034-713 超时-传输删除034-714 线路断开-超时T305034-715 线路断开-超时3082 034-716 连接超时〔T313〕.034-717 Resume 超时034-718 正常断开034-719 无空闲和有效线路034-720 超时〔60s,T330,309,301,310〕034-721 错误〔格式化，容〕034-722悬挂超时034-723 无指定计时器034-724 非法顺序034-725 L3 任务部错误034-726 HD81501 I/F 缓冲器忙034-727 任务无响应〔对1300Hz 输入呼叫为3 秒〕034-728 无效的目标034-729 线路切断，部通道PB 发送034-730 输入和输出呼叫冲突034-731 网络切断〔设置错误〕034-732 网络因超时而被切断034-733 不正确顺序，呼叫状态034-734 HI 任务部错误034-735 只与ISDN D 信道连接034-736 来自网络的错误通知034-737 输入呼叫响应错误034-738 层1 启动错误034-739 层1 不同步034-740 帧传输错误034-741 不能发送帧034-742 帧发送低速被检测034-743 不正常发送帧DMA034-744 不能承受的信道034-745 呼出信道设置034-746 无可使用线路034-747 转换设备拥挤034-748 指定线路无法使用034-750 网络错误034-751 临时网络错误034-752 目标终端忙034-753 目标不应答034-754 无来自目标的响应034-755 目标拒绝呼叫034-756 目标故障034-757 其它〔正常，半正常〕034-758 不正确目标拨号034-759 无中转网络路由034-760 无到目标线路034-761 不正确格式目标034-762 设备拒绝034-763 通讯能力不允许034-764 通讯能力未被配置034-765 效劳，性能限制带来的错误034-766 所选择的通讯不执行034-767 所选模式不执行034-768 只有有限数字信息034-769 效劳，性能产生的错误034-770 应答状态查询034-771 访问信息被放弃034-772 工作之间连接错误034-773 指定拨号无效034-774 指定的线路无效034-775 其他〔无效信息类〕034-776 所需信息不够034-777 不明确的信息类型034-778 不正确信息或类型034-779 无信息或未定义034-780 无效信息034-781 呼叫状态，信息不匹配034-782 因超时而被错误去除034-783 其它错误〔操作等〕034-784 目标改变034-785 不兼容目标034-786 呼叫识别码不在使用中034-787 呼叫识别码在使用中034-788 显示其它原因034-789 G4 表示层非法事件034-790 线路1 未被连接034-791 线路0〔分机〕未被连接034-792 线路2 未被连接034-793 线路3 未被连接034-794 线路4未被连接034-795 线路5 未被连接034-796 拨号错误〔不正确 2〕034-797 通讯参数错误034-798 数据参数错误034-799 自动拨号无拨号数据035-**x 网络035-700 Modem 故障035-701 T1 传输超时035-702 目标接收被拒绝035-703 以相位B 发送时接收到D.035-704 目标轮询错误035-705 DCS/NSS 重新发送超限035-706 减速运行错误035-707 错误的口令/接收错误035-708 后-信息重发超限035-709 RTN 接收035-710 PIN 接收035-711 D 接收在相位D035-712 3 NSC 后无响应035-713 发送FTT 之后T2 超时035-714 NSC/DTC 之后接收到D 035-715 错误口令-轮询错误035-716 无后信息-T2 超时035-717 RTN 发送035-718 接收T1 超时035-719 检测到忙音035-720 不能被远程机器接收035-721 D 接收在相位B035-722 错误的300bps 帧长度035-723 接收标记之后无CD035-724 发送FTT 之后接收D 035-725 远程机器没有/中继035-726 相位C 不能接收-10 秒035-727 G3 接收期间50%错误035-728 C EOL 不能在10 秒之接收035-729 检测到载波减弱035-730 相位C 高速无CS035-731 V.8 错误035-732 V.34 PCH CD Off035-733 V.34 C/PCH CS 无035-734 远程V8 程序轮询错误035-735 轮询箱V8 程序中无文件035-736 发送CTC 之后无应答D 035-737 发送EOR 之后无应答D 035-738 发送RR 之后无应答D 035-739 15 超时035-740 E-OR 发送之后发送停顿035-741 ECM 相位C 标记超时035-742 EOR 发送或接收035-743 远程机器不能接收SUB 035-744 远程机器不能接收口令035-745 PTX 无SEP 功能035-746 忙-不能检测拨号音035-747 拨号时中止035-748 传输期间中止035-749 无来自远程站的应答035-750 传输期间电源Off035-751 文件发送操作被删除035-752 作业数限制错误035-753 存储器满035-754 文件管理存储器满035-755 文件加页错误035-756 不能加页035-757 无接收页035-758 无指定文件或页035-759 无指定作业035-760 文件公共处理错误035-761 文件其它处理错误035-762 ISDN 期间线路切断036-**x 参数036-500 非法PDRP 参数036-501 非法RDPBP 参数036-502 非法RDPBN 参数036-503 非法RDCLP 参数036-504 非法RDGR 参数036-505 未定义响应036-506 不可协商036-507 在容量满时接收RDPBN 036-508 RDPBN 接收终端错误036-509 RDPBN 接收其它036-510 RDGR 接收036-511 非法程序1551036-512 非法CDS 参数036-513 非法CDC 参数036-514 非法CDE 参数036-515 非法CDD 参数036-516 非法CDR 参数036-517 非法CDPB 参数036-518 非法CDCL 参数036-519 未定义命令036-520 不可协商CDS 接收036-521 不可协商CDC 接收036-522 CDD 接收终端错误036-523 除以上CDD 接收外的其它036-524 CDR 接收终端错误036-525 除以上CDR 接收外的其它036-526 非法CDUI〔正常文件〕036-527 非法CDUI〔操作者文件〕.036-528 非法CDUI〔控制文件〕036-529 非法CDUI〔监视文件〕036-530 CDS 接收-非法文件036-531 DMA 信道1 非法关闭036-532 DMA 信道2 非法关闭036-533 不能转换资料036-534 数据转换中的解码错误036-535 白线转移错误〔压缩〕036-536 白线转移错误〔解码〕036-537 数据转换期间无RTC036-538 文件描述符分析错误036-539 页面描述符分析错误036-540 文本单元分析错误036-541 页边界无TU036-542 G4 中继广发错误036-700 G4 通讯错误036-701 接收可变N〔R〕错误036-702 信息帧尺寸超出〔NI〕036-703 监视不可计数帧错误036-704 未定义命令/应答1104036-705 接收计时器N2 超时036-706 G4 中SABM 等待超时036-707 G4 中UA 等待超时036-708 不能在G4 中建立连接036-709 连接关闭之前接收DISC036-710 FRMR 接收〔Z=1〕036-711 FRMR 接收〔Y=1〕036-712 FRMR 接收〔Z=1〕W=1036-713 FRMR 接收〔W=1〕036-714 全局地址接收036-715 G4 线路开放超时036-716 LSI 发送错误〔发送忙，超时〕036-717 LSI 操作错误036-718 断开通知超时036-719 C 线路On 但是I 线路Off 036-720 C 线路Off 但是I 线路On 036-721 传输期间I 线路Off036-722 标记检测期间呼叫中止036-723 等待UA 期间呼叫中止036-724 等待SABM 期间呼叫中止036-725 会话之前接收到Disc036-726 非法页眉被接收036-727 CC 包非法参数036-728 包非法参数036-729 DT 包非法参数036-730 RI 包非法参数036-731 IT 包非法参数036-732 CI 包非法参数036-733 CF 包非法参数036-734 未定义包被接收036-735 CC 等待超时036-736 CF 等待超时036-737 G4 会话之前接收到CI 036-738 DT 包P〔S〕，P〔R〕错误036-739 RR，RNR 包P〔S〕错误036-740 忙超时036-741 传输中接收到SI036-742 传输中接收到SF036-743 DT 包D Bit 错误036-744 G4 等待应答超时036-745 G4 等待超时036-746 G4 断开通知超时036-747 快速选择响应接收036-748 接收远程收费请求036-749 异常LCGN036-750 非法程序1301036-751 非法TCA 参数036-752 非法TCR 参数036-753 非法TCC 参数036-754 非法TBR 参数036-755 非法TDT 参数036-756 未定义的传输块036-757 TCA 等待超时036-758 TCR 等待超时036-759 TCC 等待超时036-760 TBR 等待超时036-761 TDT 块尺寸错误036-762 G4 网络断开通知超时036-763 非法程序1401036-764 非法CSS 参数036-765 非法CSE 参数036-766 非法CSA 参数036-767 非法CSUI 参数036-768 非法CSCC 参数036-769 非法RSSP 参数036-770 非法RSSN 参数036-771 非法RSEP 参数036-772 非法RSAP 参数036-773 非法RSUI 参数036-774 非法RSCCP 参数036-775 未定义命令/应答1413036-776 RSSN 接收036-777 断开通知超时036-778 CSA 接收〔错误终端〕036-779 CSA 接收〔其它〕036-780 CSS 等待超时036-781 RSSP 等待超时036-782 RSAP 等待超时036-783 RSEP 等待超时036-784 RSCCP 等待超时036-785 CSUI/RSUI 等待超时036-786 不正确口令〔RSSN〕036-787 错误口令-轮询出错〔对远程轮询〕036-788 轮询发送错误〔在远处〕036-789 无RSSP 口令接收036-790 轮询被远程机器拒绝036-791 设置口令-RSSP 被接收036-792 RSSP 发送之后CSE 被接收036-793 选择通讯错误036-794 G4 模式期间线路断开036-795 被远程站删除036-796 无多份发送036-797 非法程序1501036-798 非法RDEP 参数036-799 非法RDDP 参数041-**x NVM041-210 MCU NVM 失控纸盘模块041-211 NVM 读/写故障纸盘模块041-340 MCU RAM 读/写故障041-362 IOT NVM 读/写故障041-363 MCU NVM 断路故障041-364 访问NVM 的MCU CPU 功率不够041-366 MCU 控制Crum 的Asic 电路有缺陷042-**x 驱动042-323 鼓K 电机驱动故障042-325 主电机故障047-**x 通讯047-211 OCT1 故障047-212 OCT2 故障047-213 装订器不同类型047-214 MCU-DM 通讯错误047-215 MCU-EXIT 通讯错误047-216 MCU-装订器通讯错误047-218 MCU-TM 通讯错误061-**x ROS061-315 SOS 长K 故障061-321 ROS 电机故障061-333 ROS 风扇缺陷062-**x IIT062-210 IISS 热线故障062-211 IISS EEPROM 本地故障062-277 IISS-DADF 通讯故障062-300 稿台联锁翻开062-310 IISS-控制器通讯故障062-311 IISS 软件逻辑故障062-345 IISS EEPROM 子系统故障062-360 灯架位置故障062-371 灯照明故障062-380 稿台AGC CH 1 故障062-386 稿台AOC CH 1 故障062-389 灯架过速故障062-392 IISS PWBA 存储器故障-1062-393 IISS PWBA 存储器故障-2071-**x 纸盘1071-105 纸盘1 定位传感器On 卡纸071-210 纸盘1 提升故障071-211 纸盘1 故障072-**x 纸盘2072-101 纸盘2 错误输送卡纸072-105 纸盘2 定位传感器On 卡纸072-210 纸盘2 提升故障072-211 纸盘2 故障073-**x 纸盘3073-101 纸盘3 错误输送卡纸073-102 纸盘2 输出传感器On 卡纸〔纸盘3 输送〕073-105 纸盘3 定位传感器On 卡纸073-210 纸盘3 提升故障073-211 纸盘3 故障074-**x 纸盘4074-101 纸盘4 错误输送卡纸074-102 纸盘2 输出传感器On 卡纸〔纸盘4 输送〕074-103 纸盘3 输出传感器On 卡纸〔纸盘4 输送〕074-105 纸盘4 定位传感器On 卡纸074-210 纸盘4 提升故障074-211 纸盘4 故障075-**x MPT075-135 MSI 定位传感器On 卡纸077-**x 卡纸和盖翻开077-101 定位传感器Off 卡纸077-103 定影器出口传感器Off 卡纸077-104 出口传感器〔太短〕卡纸077-106 定影出口传感器On 卡纸077-109 IOT 出口传感器On 卡纸〔笔直〕077-113 IOT 出口传感器Off 卡纸〔笔直〕077-114 出口2 传感器静态卡纸077-129 定位传感器On 卡纸〔双面输送/停顿情况〕077-130 双面输出传感器On 卡纸077-131 双面等待传感器On 卡纸077-211 检测不同类型纸盘模块077-300 IOT 前盖翻开077-301 左联锁翻开077-305 纸盘模块左盖联锁翻开077-307 双面器盖翻开077-308 左上联锁翻开077-309 左下联锁翻开077-310 控制器无法发送图像077-329 主电机停顿错误077-900 定位传感器静态卡纸077-901 定影器出口传感器静态卡纸077-902 出口传感器2On 卡纸待机077-904 纸盘2 输出传感器静态卡纸077-905 纸盘3 输出传感器静态卡纸077-906 纸盘4 输出传感器静态卡纸077-907 双面传感器静态卡纸081-**x 目的081-799 未登记目标091-**x 鼓091-401 鼓寿命接近完毕091-912 静电复印/显影器盒设置故障091-913 静电复印/显影器盒寿命完毕091-914 静电复印/显影器盒CRUM 传输故障091-915 静电复印/显影器盒CRUM 数据写入故障091-916 鼓CRUM 数据不匹配092-**x 过程控制092-910 ATC 传感器故障093-**x 墨粉供给093-312 分配电机故障093-406 黑墨粉接近空093-912 黑墨粉空093-924 墨粉盒CRUM 传输故障093-925 墨粉CRUM 数据中断故障093-926 墨粉CRUM 数据不匹配故障102-**x UI102-356 EWS 软件故障102-380 MF UI 控制器致命错误102-381 数据层错误〔UI-板〕102-382 应用层命令错误〔UI-板〕116-**x 打印控制116-310 ESS 字模ROM DIMM#2 检查故障116-312 HDD 加密键故障116-313 HDD 加密设置故障116-314 Ethernet 地址故障116-315 ESS RAM DIMM#1 读/写检查故障116-316 ESS RAM DIMM#2 读/写检查故障116-317 ESS ROM DIMM#1 检查故障116-318 ESS ROM DIMM#2 检查故障116-321 系统软件致命错误116-323 ESS NVRAM 读/写检查故障116-324 系统检测到一错误116-326 ESS ROM DIMM#1 Flash 故障116-327 ESS ROM DIMM#2 Flash 故障116-328 二级高速缓冲故障116-329 串行IF 软件故障116-330 HDD 文件系统故障116-331 无效记录信息116-332 ESS 在板ROM 错误116-333 Local Talk 软件故障116-335 MFIO HD 故障116-336 重定向器HD 故障116-337 SNTP 软件故障116-338 A 致命错误116-339 HDD 不连接A116-340 存不够116-341 ROM 版本不正确116-342 SESAMi 管理故障116-343 主PWB IC 故障116-344 MFIO 故障116-346 Formatter 故障116-348 Redirector 故障.116-349 SIF 呼叫Pflite 故障116-350 Apple Talk 软件故障116-351 Ether Talk 软件故障116-352 NetWare 软件故障116-353 HDD 管理故障116-354 HDD 产品故障116-355 Agent 软件故障116-356 HDD 格式化故障116-357 Postcript 错误116-358 Salutation 软件故障116-359 PL W 软件故障116-360 SMB 软件故障116-361 假脱机致命错误HDD116-362 SSDP 软件故障116-363 BMLinkS/打印效劳软件故障116-364 计时器故障116-365 假脱机致命错误116-366 报告Gen.软件故障116-367 并口IF 软件故障116-368 转储打印故障116-370 XJCL 故障116-371 PCL 解压缩器软件故障116-372 P-格式化故障116-373 动态DNS 软件故障116-374 自动转换故障116-375 I-格式化故障116-376 Port 9100 软件故障116-377 视频DMA 故障116-378 MCR 软件故障116-379 MCC 软件故障116-380 ESS 字模ROM DIMM#1 检查故障116-381 ABL 初始化故障116-382 ABL 物理初始化故障116-385 IDC 软件故障116-388 MCC〔容起始码〕致命错误116-389 需附加RAM 但是未安装116-390 标准ROM 和NVM 版本不匹配116-391 非法代码检测116-392 非法地区代码检测116-393 非法纸尺寸组检测116-395 USB 软件故障116-701 超出存-双面故障116-702 用替代字模打印116-703 PostScript 语言翻译错误116-710 HP-GL/2 存溢出116-711 PL W 尺寸/方向不匹配116-712 区域以外-表格登记错误116-713 作业因HDD 满而被分隔116-714 HP-GL/2 命令错误116-715 PL W 注册的最大表格数116-718 所选PL W 表格未被注册116-720 PCL 存缺乏，页面简化116-737 超出区域-数据注册错误116-738 尺寸/方向不匹配116-739 表格/Logo 容量不够116-740 算法错误116-741 非PL W 注册的最大表格数116-742 最大注册Logo116-743 表格/Logo 尺寸溢出116-745 ART 命令错误116-746 所选表格未被注册116-747 无效页边界116-748 无图像数据页面116-749 PostScript 字模错误116-771 无效IG 参数DL 调整116-772 无效IG 参数D 调整116-773 无效IG 参数P 调整116-774 无效IG 参数YD 调整116-775 无效IG 参数L0 调整116-776 无效IG 参数MX 调整116-777 无效IG 参数MY 调整116-778 无效IG Par VLENGTH116-780 附属文件错误116-790 装订被取消121-**x EP121-310 EPSV-附件通讯故障121-333 EPSV-EP M/C 通讯故障121-334 EPSV 登录故障121-335 EPSV 唤醒应答故障121-336 未知EP 附件121-337 EP 附件自诊故障121-338 EPSV 应答超时121-339 变化的价格表121-340 EP 附件不匹配121-350 EPSV 逻辑故障121-370 EP-DX-未曾预计错误123-**x 软件123-200 接收缓冲器溢出123-201 发送缓冲器溢出〔UI-面板〕123-202 请求队列满〔UI-面板〕123-205 SIO 命令故障〔UI-面板〕123-206 SIO 状态故障〔UI-面板〕123-207 命令管理器目标故障〔UI-面板〕123-208 命令管理器命令故障〔UI-面板〕123-310 发送队列满〔UI-面板〕123-311 接收队列满〔UI-面板〕123-312 EVM 使用错误的API〔UI-面板〕123-313 AS 使用错误的API〔UI-面板〕123-314 事件-等待计时器超时〔UI-面板〕123-315 CTS 部故障〔UI-面板〕123-316 发送请求队列满SIO〔UI-面板〕123-317 接收信息队列满〔UI-面板〕123-318 接收完毕队列满〔UI-面板〕123-319 发送故障-无ACK〔UI-面板〕123-320 轮询故障〔UI-面板〕123-321 发送消息故障〔UI-面板〕123-322 目标故障〔UI-面板〕123-323 地址故障〔UI-面板〕123-324 尺寸故障〔UI-面板〕123-325 对象创立故障〔UI-面板〕123-326 存溢出〔UI-面板〕123-327 按钮溢出〔UI-面板〕123-328 UI 部故障-超出围123-329 UI 部故障-无效坐标123-330 接口故障-无效参数LCD123-331 UI 部故障-无效LED 请求123-332 接口故障〔无效参数CP〕123-333 接口故障〔不可能的通讯〕123-334 接口故障〔接收错误的键代码〕123-335 接口故障〔接收无效坐标〕123-336 接口故障〔DM-ACD 驱动〕123-337 帧数据错误〔具有无效的数据类型〕123-338 接口故障〔错误地址超出围〕123-339 显示请求代码无效123-340 接口故障GUAM-DM I/F123-341 事件队列满〔UI-面板〕123-342 事件队列空〔UI-面板〕123-343 无效对象组〔UI-面板〕123-344 无效类型〔UI-面板〕123-345 计时器队列满〔UI-面板〕123-346 无效计时器数字〔UI-面板〕123-347 不明陷阱〔UI-面板〕123-348 命令选取异样〔UI-面板〕123-349 无效命令〔UI-面板〕123-350 特许命令〔UI-面板〕123-351 无FPU 例外〔UI-面板〕123-352 地址不一致〔UI-面板〕123-353 数据访问异样〔UI-面板〕123-354 标签溢出〔UI-面板〕123-355 无Co 处理器例外〔UI-面板〕123-356 区域短缺〔UI-面板〕123-357 删除等待状态〔UI-面板〕123-358 超时〔UI-面板〕123-359 队列溢出〔UI-面板〕123-360 上下文故障〔UI-面板〕123-361 对象故障〔UI-面板〕123-362 无对象〔UI-面板〕123-363 无效ID〔UI-面板〕123-364 参数故障〔UI-面板〕123-365 保存属性〔UI-面板〕123-366 保存功能代码〔UI-面板〕123-367 不支持的功能〔UI-面板〕123-368 UI 存缺乏〔UI-面板〕123-369 无效接口值〔UI-面板〕123-370 接口长度故障〔UI-面板〕123-371 接口参数故障〔UI-面板〕123-372 接口顺序故障〔UI-面板〕123-373 信道故障〔UI-面板〕123-374 无效用户作业ID〔UI-面板〕123-375 部资源故障〔UI-面板〕123-376 部存储器故障〔UI-面板〕123-377 UI 计时器〔UI-面板〕123-378 接口格式故障〔UI-面板〕123-379 发送故障〔UI-面板〕123-380 复印接口故障〔UI-面板〕123-381 接口故障〔UI-面板〕123-382 扫描器接口故障〔UI-面板〕123-383 报告接口故障〔UI-面板〕123-384 效劳器访问故障〔UI-面板〕123-385 效劳对象溢出〔UI-面板〕123-386 无效效劳对象〔UI-面板〕123-387 无效效劳对象属性〔UI-面板〕123-388 属性故障〔UI-面板〕123-389 主题故障〔UI-面板〕123-390 作业参数故障〔UI-面板〕123-391 作业实际参数故障〔UI-面板〕123-392 审计故障〔UI-面板〕123-393 EP 故障〔UI-面板〕。