当前位置：文档之家 › ST7565P_V19

ST7565P_V19

  • 格式：pdf
  • 大小：840.03 KB
  • 文档页数：72

ST Sitronix ST7565P65 x 132 Dot Matrix LCD Controller/DriverF E A T U R E SDirectly display RAM data through Display Data RAM. RAM capacity : 65 x 132 = 8580 bitsDisplay duty selectable by select pin1/65 duty : 65 common x 132 segment1/49 duty : 49 common x 132 segment1/33 duty : 33 common x 132 segment1/55 duty : 55 common x 132 segment1/53 duty : 53 common x 132 segmentHigh-speed 8-bit MPU interface:ST7565P can be connected directly to both the 80x86series MPUs and the 6800 series MPUs.Serial interface (SPI-4) is also supported.Abundant command functions:Display data Read/Write, display ON/OFF, Normal/Reverse display mode, page address set, display start line set, column address set, status read, display allpoints ON/OFF, LCD bias set, electronic volume,read/modify/write, segment driver direction selects,power saver, static indicator, common output statusselect, V0 voltage regulator internal resistor ratio set. Static drive circuit equipped internally for indicators.(1 system, with variable flashing speed.)Low-power liquid crystal display power supply circuit equipped internally.Booster circuit has boost ratios of 2X/3X/4X/5X/6X.The step-up voltage reference uses external power. High-accuracy voltage adjustment circuit (Thermal gradient –0.05%/°C ) V0 voltage regulator resistorsequipped internally, V1 to V SS voltage divider resistorsequipped internally, electronic volume functionequipped internally, voltage follower.Embedded R-C oscillator circuit.The external clock is also supported.Extremely low power consumption Operating power when the built-in power supply is used (an example)60uA (V DD – V SS = V DD2 – V SS =3.0 V, Quad voltage,V0 – V SS = 11.0 V).Conditions: When displays pattern OFF and the normal mode is selected.Power supply operate on the low 1.8 voltage Logic power supply: V DD – V SS = 1.8V to 3.3VBoost reference voltage: V DD2 – V SS = 2.4V to 3.3V Booster voltage maximum limitation: V OUT = 13.5VLiquid crystal drive power supply:V0 – V SS = 3.0V to 12.0 VWide range of operating temperatures: –30 to 85°CCMOS process.Package type: Bare chip and TCP.ST7565P is not designed for resistance to light or resistance to radiation.G E N E R A L D E S C R I P T I O NThe ST7565P is a single-chip dot matrix LCD driver that can be connected directly to a microprocessor bus. 8-bit parallel or serial display data sent from the microprocessor is stored in the internal display data RAM and the chip generates a LCD drive signal independent of the microprocessor. Because the chips in the ST7565P contain 65x132 bits of display data RAM and there is a 1-to-1 correspondence between the LCD panel pixels and the internal RAM bits, these chips enable displays with a high degree of freedom. The ST7565P chips contain 65 common output circuits and 132 segment output circuits, so that a single chip can drive a 65x132 dot display (capable of displaying 8 columnsx4 rows of a 16x16 dot kanji font).Moreover, the capacity of the display can be extended through the use of master/slave structures between chips. The chips are able to minimize power consumption because no external operating clock is necessary for the display data RAM read/write operation. Furthermore, because each chip is equipped internally with a low-power LCD driver power supply, resistors for LCD driver power voltage adjustment and a display clock CR oscillator circuit, the ST7565P can be used to create the lowest power display system with the fewest components for high-performance portable devices.PART NO. V RS temperature gradient V RS range ST7565P -0.05%/°C 2.1V ± 0.03VS T7565P P a d A r r a n g e m e n t(C O G)Chip Size: 9,336μm x 1,000 μmBump Pitch: 58μm(Min.)Bump Size: PAD No. 001～012 40μm x 90μmPAD No. 013～102 56μm x 60μmPAD No. 103～114 40μm x 90μmPAD No. 115 102μm x 37.5μmPAD No. 116～128 90μm x 40μmPAD No. 129～276 40μm x 90μmPAD No. 277～289 90μm x 40μmPAD No. 290 102μm x 37.5μmBump Height: 17μmChip Thickness: 635μmUse select pin to define display duty as following table:Gold Bump SEL 3 , 2 , 10 , 0 , 00 , 0 , 10 , 1 , 00 , 1 , 11 , 0 , 030µmP a d C e n t e r C o o r d i n a t e s(1/65D u t y)U n i t s:μmPADNo.PIN Name X Y 1COM[53]4241 374 2COM[54]4183 374 3COM[55]4125 374 4COM[56]4067 374 5COM[57]4009 374 6COM[58]3951 374 7COM[59]3893 374 8COM[60]3835 374 9COM[61]3777 374 10COM[62]3719 374 11COM[63]3661 374 12COMS13603 374 13FRS3443 389 14FR3369 389 15CL3295 389 16/DOF3221 389 17VSS3147 389 18/CS13073 389 19CS22999 389 20VDD2925 389 21/RES2851 389 22A02777 389 23VSS2703 389 24/WR(R/W) 2629 389 25/RD(E) 2555 389 26VDD2481 389 27D02407 389 28D12333 389 29D22259 389 30D32185 389 31D42111 389 32D52037 389 33D61963 389 34D71889 389 35VDD1815 389 36VDD21741 389 37VDD21667 389 38VSS1593 389 39VSS1519 389 40VSS1445 389 41VSS1371 389 42VOUT1297 389 43VOUT1223 389 44CAP5P1149 389 45CAP5P1075 389 46CAP1N1001 389 47CAP1N927 389 PADNo.PIN Name X Y 48CAP3P853 389 49CAP3P779 389 50CAP1N705 389 51CAP1N631 389 52CAP1P557 389 53CAP1P483 389 54CAP2P409 389 55CAP2P335 389 56CAP2N261 389 57CAP2N187 389 58CAP4P113 389 59CAP4P39 389 60VSS-35 389 61VSS-109 389 62VRS-183 389 63VRS-257 389 64VDD2-331 389 65VDD-405 389 66V4-479 389 67V4-553 389 68V3-627 389 69V3-701 389 70V2-775 389 71V2-849 389 72V1-923 389 73V1-997 389 74V0-1071 389 75V0-1145 389 76VR-1219 389 77VR-1293 389 78VDD-1367 389 79VDD2-1441 389 80TEST0 -1515 389 81TEST1 -1589 389 82TEST2 -1663 389 83TEST3 -1737 389 84TEST4 -1811 389 85TEST5 -1885 389 86VDD-1959 389 87M/S-2033 389 88CLS-2107 389 89VSS-2181 389 90C86-2255 389 91P/S-2329 389 92VDD-2403 389 93/HPM-2477 389 94VSS-2551 389PADNo.PIN Name X Y 199SEG[62]-207-374 200SEG[63]-149-374 201SEG[64]-91-374 202SEG[65]-33-374 203SEG[66]25-374 204SEG[67]83-374 205SEG[68]141-374 206SEG[69]199-374 207SEG[70]257-374 208SEG[71]315-374 209SEG[72]373-374 210SEG[73]431-374 211SEG[74]489-374 212SEG[75]547-374 213SEG[76]605-374 214SEG[77]663-374 215SEG[78]721-374 216SEG[79]779-374 217SEG[80]837-374 218SEG[81]895-374 219SEG[82]953-374 220SEG[83]1011-374 221SEG[84]1069-374 222SEG[85]1127-374 223SEG[86]1185-374 224SEG[87]1243-374 225SEG[88]1301-374 226SEG[89]1359-374 227SEG[90]1417-374 228SEG[91]1475-374 229SEG[92]1533-374 230SEG[93]1591-374 231SEG[94]1649-374 232SEG[95]1707-374 233SEG[96]1765-374 234SEG[97]1823-374 235SEG[98]1881-374 236SEG[99]1939-374 237SEG[100]1997-374 238SEG[101]2055-374 239SEG[102]2113-374 240SEG[103]2171-374 241SEG[104]2229-374 242SEG[105]2287-374 243SEG[106]2345-374 244SEG[107]2403-374 245SEG[108]2461-374 PADNo.PIN Name X Y 246SEG[109]2519-374 247SEG[110]2577-374 248SEG[111]2635-374 249SEG[112]2693-374 250SEG[113]2751-374 251SEG[114]2809-374 252SEG[115]2867-374 253SEG[116]2925-374 254SEG[117]2983-374 255SEG[118]3041-374 256SEG[119]3099-374 257SEG[120]3157-374 258SEG[121]3215-374 259SEG[122]3273-374 260SEG[123]3331-374 261SEG[124]3389-374 262SEG[125]3447-374 263SEG[126]3505-374 264SEG[127]3563-374 265SEG[128]3621-374 266SEG[129]3679-374 267SEG[130]3737-374 268SEG[131]3795-374 269COM[32]3853-374 270COM[33]3911-374 271COM[34]3969-374 272COM[35]4027-374 273COM[36]4085-374 274COM[37]4143-374 275COM[38]4201-374 276COM[39]4259-374 277COM[40]4542-345 278COM[41]4542-287 279COM[42]4542-229 280COM[43]4542-171 281COM[44]4542-113 282COM[45]4542-55 283COM[46]4542 3 284COM[47]454261 285COM[48]4542119 286COM[49]4542177 287COM[50]4542235 288COM[51]4542293 289COM[52]4542351 290(NC)4542404P a d C e n t e r C o o r d i n a t e s(1/49D u t y)U n i t s:μmPADNo.PIN Name X Y 1COM[37]4241 374 2COM[38]4183 374 3COM[39]4125 374 4COM[40]4067 374 5COM[41]4009 374 6COM[42]3951 374 7COM[43]3893 374 8COM[44]3835 374 9COM[45]3777 374 10COM[46]3719 374 11COM[47]3661 374 12COMS13603 374 13FRS3443 389 14FR3369 389 15CL3295 389 16/DOF3221 389 17VSS3147 389 18/CS13073 389 19CS22999 389 20VDD2925 389 21/RES2851 389 22A02777 389 23VSS2703 389 24/WR(R/W) 2629 389 25/RD(E) 2555 389 26VDD2481 389 27D02407 389 28D12333 389 29D22259 389 30D32185 389 31D42111 389 32D52037 389 33D61963 389 34D71889 389 35VDD1815 389 36VDD21741 389 37VDD21667 389 38VSS1593 389 39VSS1519 389 40VSS1445 389 41VSS1371 389 42VOUT1297 389 43VOUT1223 389 44CAP5P1149 389 45CAP5P1075 389 46CAP1N1001 389 47CAP1N927 389 PADNo.PIN Name X Y 48CAP3P853 389 49CAP3P779 389 50CAP1N705 389 51CAP1N631 389 52CAP1P557 389 53CAP1P483 389 54CAP2P409 389 55CAP2P335 389 56CAP2N261 389 57CAP2N187 389 58CAP4P113 389 59CAP4P39 389 60VSS-35 389 61VSS-109 389 62VRS-183 389 63VRS-257 389 64VDD2-331 389 65VDD-405 389 66V4-479 389 67V4-553 389 68V3-627 389 69V3-701 389 70V2-775 389 71V2-849 389 72V1-923 389 73V1-997 389 74V0-1071 389 75V0-1145 389 76VR-1219 389 77VR-1293 389 78VDD-1367 389 79VDD2-1441 389 80TEST0 -1515 389 81TEST1 -1589 389 82TEST2 -1663 389 83TEST3 -1737 389 84TEST4 -1811 389 85TEST5 -1885 389 86VDD-1959 389 87M/S-2033 389 88CLS-2107 389 89VSS-2181 389 90C86-2255 389 91P/S-2329 389 92VDD-2403 389 93/HPM-2477 389 94VSS-2551 389PADNo.PIN Name X Y 199SEG[62]-207-374 200SEG[63]-149-374 201SEG[64]-91-374 202SEG[65]-33-374 203SEG[66]25-374 204SEG[67]83-374 205SEG[68]141-374 206SEG[69]199-374 207SEG[70]257-374 208SEG[71]315-374 209SEG[72]373-374 210SEG[73]431-374 211SEG[74]489-374 212SEG[75]547-374 213SEG[76]605-374 214SEG[77]663-374 215SEG[78]721-374 216SEG[79]779-374 217SEG[80]837-374 218SEG[81]895-374 219SEG[82]953-374 220SEG[83]1011-374 221SEG[84]1069-374 222SEG[85]1127-374 223SEG[86]1185-374 224SEG[87]1243-374 225SEG[88]1301-374 226SEG[89]1359-374 227SEG[90]1417-374 228SEG[91]1475-374 229SEG[92]1533-374 230SEG[93]1591-374 231SEG[94]1649-374 232SEG[95]1707-374 233SEG[96]1765-374 234SEG[97]1823-374 235SEG[98]1881-374 236SEG[99]1939-374 237SEG[100]1997-374 238SEG[101]2055-374 239SEG[102]2113-374 240SEG[103]2171-374 241SEG[104]2229-374 242SEG[105]2287-374 243SEG[106]2345-374 244SEG[107]2403-374 245SEG[108]2461-374 PADNo.PIN Name X Y 246SEG[109]2519-374 247SEG[110]2577-374 248SEG[111]2635-374 249SEG[112]2693-374 250SEG[113]2751-374 251SEG[114]2809-374 252SEG[115]2867-374 253SEG[116]2925-374 254SEG[117]2983-374 255SEG[118]3041-374 256SEG[119]3099-374 257SEG[120]3157-374 258SEG[121]3215-374 259SEG[122]3273-374 260SEG[123]3331-374 261SEG[124]3389-374 262SEG[125]3447-374 263SEG[126]3505-374 264SEG[127]3563-374 265SEG[128]3621-374 266SEG[129]3679-374 267SEG[130]3737-374 268SEG[131]3795-374 269Reserve3853-374 270Reserve 3911-374 271Reserve 3969-374 272Reserve 4027-374 273Reserve 4085-374 274Reserve 4143-374 275Reserve 4201-374 276Reserve 4259-374 277COM[24]4542-345 278COM[25]4542-287 279COM[26]4542-229 280COM[27]4542-171 281COM[28]4542-113 282COM[29]4542-55 283COM[30]4542 3 284COM[31]454261 285COM[32]4542119 286COM[33]4542177 287COM[34]4542235 288COM[35]4542293 289COM[36]4542351 290(NC)4542404P a d C e n t e r C o o r d i n a t e s(1/33D u t y)U n i t s:μmPADNo.PIN Name X Y 1COM[21]4241 374 2COM[22]4183 374 3COM[23]4125 374 4COM[24]4067 374 5COM[25]4009 374 6COM[26]3951 374 7COM[27]3893 374 8COM[28]3835 374 9COM[29]3777 374 10COM[30]3719 374 11COM[31]3661 374 12COMS13603 374 13FRS3443 389 14FR3369 389 15CL3295 389 16/DOF3221 389 17VSS3147 389 18/CS13073 389 19CS22999 389 20VDD2925 389 21/RES2851 389 22A02777 389 23VSS2703 389 24/WR(R/W) 2629 389 25/RD(E) 2555 389 26VDD2481 389 27D02407 389 28D12333 389 29D22259 389 30D32185 389 31D42111 389 32D52037 389 33D61963 389 34D71889 389 35VDD1815 389 36VDD21741 389 37VDD21667 389 38VSS1593 389 39VSS1519 389 40VSS1445 389 41VSS1371 389 42VOUT1297 389 43VOUT1223 389 44CAP5P1149 389 45CAP5P1075 389 46CAP1N1001 389 47CAP1N927 389 PADNo.PIN Name X Y 48CAP3P853 389 49CAP3P779 389 50CAP1N705 389 51CAP1N631 389 52CAP1P557 389 53CAP1P483 389 54CAP2P409 389 55CAP2P335 389 56CAP2N261 389 57CAP2N187 389 58CAP4P113 389 59CAP4P39 389 60VSS-35 389 61VSS-109 389 62VRS-183 389 63VRS-257 389 64VDD2-331 389 65VDD-405 389 66V4-479 389 67V4-553 389 68V3-627 389 69V3-701 389 70V2-775 389 71V2-849 389 72V1-923 389 73V1-997 389 74V0-1071 389 75V0-1145 389 76VR-1219 389 77VR-1293 389 78VDD-1367 389 79VDD2-1441 389 80TEST0 -1515 389 81TEST1 -1589 389 82TEST2 -1663 389 83TEST3 -1737 389 84TEST4 -1811 389 85TEST5 -1885 389 86VDD-1959 389 87M/S-2033 389 88CLS-2107 389 89VSS-2181 389 90C86-2255 389 91P/S-2329 389 92VDD-2403 389 93/HPM-2477 389 94VSS-2551 389PADNo.PIN Name X Y 199SEG[62]-207-374 200SEG[63]-149-374 201SEG[64]-91-374 202SEG[65]-33-374 203SEG[66]25-374 204SEG[67]83-374 205SEG[68]141-374 206SEG[69]199-374 207SEG[70]257-374 208SEG[71]315-374 209SEG[72]373-374 210SEG[73]431-374 211SEG[74]489-374 212SEG[75]547-374 213SEG[76]605-374 214SEG[77]663-374 215SEG[78]721-374 216SEG[79]779-374 217SEG[80]837-374 218SEG[81]895-374 219SEG[82]953-374 220SEG[83]1011-374 221SEG[84]1069-374 222SEG[85]1127-374 223SEG[86]1185-374 224SEG[87]1243-374 225SEG[88]1301-374 226SEG[89]1359-374 227SEG[90]1417-374 228SEG[91]1475-374 229SEG[92]1533-374 230SEG[93]1591-374 231SEG[94]1649-374 232SEG[95]1707-374 233SEG[96]1765-374 234SEG[97]1823-374 235SEG[98]1881-374 236SEG[99]1939-374 237SEG[100]1997-374 238SEG[101]2055-374 239SEG[102]2113-374 240SEG[103]2171-374 241SEG[104]2229-374 242SEG[105]2287-374 243SEG[106]2345-374 244SEG[107]2403-374 245SEG[108]2461-374 PADNo.PIN Name X Y 246SEG[109]2519-374 247SEG[110]2577-374 248SEG[111]2635-374 249SEG[112]2693-374 250SEG[113]2751-374 251SEG[114]2809-374 252SEG[115]2867-374 253SEG[116]2925-374 254SEG[117]2983-374 255SEG[118]3041-374 256SEG[119]3099-374 257SEG[120]3157-374 258SEG[121]3215-374 259SEG[122]3273-374 260SEG[123]3331-374 261SEG[124]3389-374 262SEG[125]3447-374 263SEG[126]3505-374 264SEG[127]3563-374 265SEG[128]3621-374 266SEG[129]3679-374 267SEG[130]3737-374 268SEG[131]3795-374 269Reserve3853-374 270Reserve 3911-374 271Reserve 3969-374 272Reserve 4027-374 273Reserve 4085-374 274Reserve 4143-374 275Reserve 4201-374 276Reserve 4259-374 277Reserve 4542-345 278Reserve 4542-287 279Reserve 4542-229 280Reserve 4542-171 281Reserve 4542-113 282Reserve 4542-55 283Reserve 4542 3 284Reserve 454261 285COM[16]4542119 286COM[17]4542177 287COM[18]4542235 288COM[19]4542293 289COM[20]4542351 290(NC)4542404P a d C e n t e r C o o r d i n a t e s(1/55D u t y)U n i t s:μmPADNo.PIN Name X Y 1COM[43]4241 374 2COM[44]4183 374 3COM[45]4125 374 4COM[46]4067 374 5COM[47]4009 374 6COM[48]3951 374 7COM[49]3893 374 8COM[50]3835 374 9COM[51]3777 374 10COM[52]3719 374 11COM[53]3661 374 12COMS13603 374 13FRS3443 389 14FR3369 389 15CL3295 389 16/DOF3221 389 17VSS3147 389 18/CS13073 389 19CS22999 389 20VDD2925 389 21/RES2851 389 22A02777 389 23VSS2703 389 24/WR(R/W) 2629 389 25/RD(E) 2555 389 26VDD2481 389 27D02407 389 28D12333 389 29D22259 389 30D32185 389 31D42111 389 32D52037 389 33D61963 389 34D71889 389 35VDD1815 389 36VDD21741 389 37VDD21667 389 38VSS1593 389 39VSS1519 389 40VSS1445 389 41VSS1371 389 42VOUT1297 389 43VOUT1223 389 44CAP5P1149 389 45CAP5P1075 389 46CAP1N1001 389 47CAP1N927 389 PADNo.PIN Name X Y 48CAP3P853 389 49CAP3P779 389 50CAP1N705 389 51CAP1N631 389 52CAP1P557 389 53CAP1P483 389 54CAP2P409 389 55CAP2P335 389 56CAP2N261 389 57CAP2N187 389 58CAP4P113 389 59CAP4P39 389 60VSS-35 389 61VSS-109 389 62VRS-183 389 63VRS-257 389 64VDD2-331 389 65VDD-405 389 66V4-479 389 67V4-553 389 68V3-627 389 69V3-701 389 70V2-775 389 71V2-849 389 72V1-923 389 73V1-997 389 74V0-1071 389 75V0-1145 389 76VR-1219 389 77VR-1293 389 78VDD-1367 389 79VDD2-1441 389 80TEST0 -1515 389 81TEST1 -1589 389 82TEST2 -1663 389 83TEST3 -1737 389 84TEST4 -1811 389 85TEST5 -1885 389 86VDD-1959 389 87M/S-2033 389 88CLS-2107 389 89VSS-2181 389 90C86-2255 389 91P/S-2329 389 92VDD-2403 389 93/HPM-2477 389 94VSS-2551 389PADNo.PIN Name X Y 199SEG[62]-207-374 200SEG[63]-149-374 201SEG[64]-91-374 202SEG[65]-33-374 203SEG[66]25-374 204SEG[67]83-374 205SEG[68]141-374 206SEG[69]199-374 207SEG[70]257-374 208SEG[71]315-374 209SEG[72]373-374 210SEG[73]431-374 211SEG[74]489-374 212SEG[75]547-374 213SEG[76]605-374 214SEG[77]663-374 215SEG[78]721-374 216SEG[79]779-374 217SEG[80]837-374 218SEG[81]895-374 219SEG[82]953-374 220SEG[83]1011-374 221SEG[84]1069-374 222SEG[85]1127-374 223SEG[86]1185-374 224SEG[87]1243-374 225SEG[88]1301-374 226SEG[89]1359-374 227SEG[90]1417-374 228SEG[91]1475-374 229SEG[92]1533-374 230SEG[93]1591-374 231SEG[94]1649-374 232SEG[95]1707-374 233SEG[96]1765-374 234SEG[97]1823-374 235SEG[98]1881-374 236SEG[99]1939-374 237SEG[100]1997-374 238SEG[101]2055-374 239SEG[102]2113-374 240SEG[103]2171-374 241SEG[104]2229-374 242SEG[105]2287-374 243SEG[106]2345-374 244SEG[107]2403-374 245SEG[108]2461-374 PADNo.PIN Name X Y 246SEG[109]2519-374 247SEG[110]2577-374 248SEG[111]2635-374 249SEG[112]2693-374 250SEG[113]2751-374 251SEG[114]2809-374 252SEG[115]2867-374 253SEG[116]2925-374 254SEG[117]2983-374 255SEG[118]3041-374 256SEG[119]3099-374 257SEG[120]3157-374 258SEG[121]3215-374 259SEG[122]3273-374 260SEG[123]3331-374 261SEG[124]3389-374 262SEG[125]3447-374 263SEG[126]3505-374 264SEG[127]3563-374 265SEG[128]3621-374 266SEG[129]3679-374 267SEG[130]3737-374 268SEG[131]3795-374 269Reserve 3853-374 270Reserve 3911-374 271Reserve 3969-374 272Reserve 4027-374 273Reserve 4085-374 274COM[27]4143-374 275COM[28]4201-374 276COM[29]4259-374 277COM[30]4542-345 278COM[31]4542-287 279COM[32]4542-229 280COM[33]4542-171 281COM[34]4542-113 282COM[35]4542-55 283COM[36]4542 3 284COM[37]454261 285COM[38]4542119 286COM[39]4542177 287COM[40]4542235 288COM[41]4542293 289COM[42]4542351 290(NC)4542404P a d C e n t e r C o o r d i n a t e s(1/53D u t y)U n i t s:μmPADNo.PIN Name X Y 1COM[41]4241 374 2COM[42]4183 374 3COM[43]4125 374 4COM[44]4067 374 5COM[45]4009 374 6COM[46]3951 374 7COM[47]3893 374 8COM[48]3835 374 9COM[49]3777 374 10COM[50]3719 374 11COM[51]3661 374 12COMS13603 374 13FRS3443 389 14FR3369 389 15CL3295 389 16/DOF3221 389 17VSS3147 389 18/CS13073 389 19CS22999 389 20VDD2925 389 21/RES2851 389 22A02777 389 23VSS2703 389 24/WR(R/W) 2629 389 25/RD(E) 2555 389 26VDD2481 389 27D02407 389 28D12333 389 29D22259 389 30D32185 389 31D42111 389 32D52037 389 33D61963 389 34D71889 389 35VDD1815 389 36VDD21741 389 37VDD21667 389 38VSS1593 389 39VSS1519 389 40VSS1445 389 41VSS1371 389 42VOUT1297 389 43VOUT1223 389 44CAP5P1149 389 45CAP5P1075 389 46CAP1N1001 389 47CAP1N927 389 PADNo.PIN Name X Y 48CAP3P853 389 49CAP3P779 389 50CAP1N705 389 51CAP1N631 389 52CAP1P557 389 53CAP1P483 389 54CAP2P409 389 55CAP2P335 389 56CAP2N261 389 57CAP2N187 389 58CAP4P113 389 59CAP4P39 389 60VSS-35 389 61VSS-109 389 62VRS-183 389 63VRS-257 389 64VDD2-331 389 65VDD-405 389 66V4-479 389 67V4-553 389 68V3-627 389 69V3-701 389 70V2-775 389 71V2-849 389 72V1-923 389 73V1-997 389 74V0-1071 389 75V0-1145 389 76VR-1219 389 77VR-1293 389 78VDD-1367 389 79VDD2-1441 389 80TEST0 -1515 389 81TEST1 -1589 389 82TEST2 -1663 389 83TEST3 -1737 389 84TEST4 -1811 389 85TEST5 -1885 389 86VDD-1959 389 87M/S-2033 389 88CLS-2107 389 89VSS-2181 389 90C86-2255 389 91P/S-2329 389 92VDD-2403 389 93/HPM-2477 389 94VSS-2551 389PADNo.PIN Name X Y 199SEG[62]-207-374 200SEG[63]-149-374 201SEG[64]-91-374 202SEG[65]-33-374 203SEG[66]25-374 204SEG[67]83-374 205SEG[68]141-374 206SEG[69]199-374 207SEG[70]257-374 208SEG[71]315-374 209SEG[72]373-374 210SEG[73]431-374 211SEG[74]489-374 212SEG[75]547-374 213SEG[76]605-374 214SEG[77]663-374 215SEG[78]721-374 216SEG[79]779-374 217SEG[80]837-374 218SEG[81]895-374 219SEG[82]953-374 220SEG[83]1011-374 221SEG[84]1069-374 222SEG[85]1127-374 223SEG[86]1185-374 224SEG[87]1243-374 225SEG[88]1301-374 226SEG[89]1359-374 227SEG[90]1417-374 228SEG[91]1475-374 229SEG[92]1533-374 230SEG[93]1591-374 231SEG[94]1649-374 232SEG[95]1707-374 233SEG[96]1765-374 234SEG[97]1823-374 235SEG[98]1881-374 236SEG[99]1939-374 237SEG[100]1997-374 238SEG[101]2055-374 239SEG[102]2113-374 240SEG[103]2171-374 241SEG[104]2229-374 242SEG[105]2287-374 243SEG[106]2345-374 244SEG[107]2403-374 245SEG[108]2461-374 PADNo.PIN Name X Y 246SEG[109]2519-374 247SEG[110]2577-374 248SEG[111]2635-374 249SEG[112]2693-374 250SEG[113]2751-374 251SEG[114]2809-374 252SEG[115]2867-374 253SEG[116]2925-374 254SEG[117]2983-374 255SEG[118]3041-374 256SEG[119]3099-374 257SEG[120]3157-374 258SEG[121]3215-374 259SEG[122]3273-374 260SEG[123]3331-374 261SEG[124]3389-374 262SEG[125]3447-374 263SEG[126]3505-374 264SEG[127]3563-374 265SEG[128]3621-374 266SEG[129]3679-374 267SEG[130]3737-374 268SEG[131]3795-374 269Reserve3853-374 270Reserve 3911-374 271Reserve 3969-374 272Reserve 4027-374 273Reserve 4085-374 274Reserve 4143-374 275COM[26]4201-374 276COM[27]4259-374 277COM[28]4542-345 278COM[29]4542-287 279COM[30]4542-229 280COM[31]4542-171 281COM[32]4542-113 282COM[33]4542-55 283COM[34]4542 3 284COM[35]454261 285COM[36]4542119 286COM[37]4542177 287COM[38]4542235 288COM[39]4542293 289COM[40]4542351 290(NC)4542404B L OC KD I A G R A MSEG0SEG131COM0COM63COMSFRS M/S CL DOF FRCLSD7(SI)D6(SCL)D5D4D3D2D1D0P/SC86CS2/RESCS1A0RW(/WR)E(/RD)SEL3SEL2SEL1P I N D E S C R I P T I O N SPower Supply PinsPin Name I/O Function No. of PinsVDD PowerSupplyPower supply13VDD2 PowerSupplyPower supply10VSS PowerSupplyGround2VRS PowerSupplyThis is the internal-output VREG power supply for the LCD power supply voltageregulator.2V0, V1, V2, V3, V4,Vss PowerSupplyThis is a multi-level power supply for the liquid crystal drive. The voltage Supplyapplied is determined by the liquid crystal cell, and is changed through the use of aresistive voltage divided or through changing the impedance using an op. amp.Voltage levels are determined based on Vss, and must maintain the relativemagnitudes shown below.V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧VssWhen the power supply turns ON, the internal power supply circuits produce the V1to V4 voltages shown below. The voltage settings are selected using the LCD biasset command.1/65 DUTY 1/49 DUTY 1/33 DUTY 1/55 DUTY 1/53 DUTY V1V2V3V48/9*V0,6/7*V07/9*V0,5/7*V02/9*V0,2/7*V01/9*V0,1/7*V07/8*V0,5/6*V06/8*V0,4/6*V02/8*V0,2/6*V01/8*V0,1/6*V05/6*V0,4/5*V04/6*V0,3/5*V02/6*V0,2/5*V01/6*V0,1/5*V07/8*V0,5/6*V06/8*V0,4/6*V02/8*V0,2/6*V01/8*V0,1/6*V07/8*V0,5/6*V06/8*V0,4/6*V02/8*V0,2/6*V01/8*V0,1/6*V010LCD Power Supply PinsPin Name I/O Function No. of PinsCAP1P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.4CAP1N O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal.2CAP2P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.2CAP2N O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal.2CAP3P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.2CAP4P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal.2CAP5P O DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal.2VOUT O DC/DC voltage converter. Connect a capacitor between this terminal and VSS orVDD2VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 througha resistive voltage divider.IRS = “L” : the V0 voltage regulator internal resistors are not used.IRS = “H” : the V0 voltage regulator internal resistors are used.2System Bus Connection PinsPin Name I/O Function No. of Pins D5 to D0D6 (SCL) D7 (SI)I/OThis is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standardMPU data bus.When the serial interface (SPI-4) is selected (P/S = “L”) :D7 : serial data input (SI) ; D6 : the serial clock input (SCL).D0 to D5 should be connected to VDD or floating.When the chip select is not active, D0 to D7 are set to high impedance.8A0I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.A0 = “H”: Indicates that D0 to D7 are display data.A0 = “L”: Indicates that D0 to D7 are control data.1/RES I When /RES is set to “L”, the register settings are initialized (cleared).The reset operation is performed by the /RES signal level.1/CS1 CS2I This is the chip select signal. When /CS1 = “L” and CS2 = “H”, then the chip selectbecomes active, and data/command I/O is enabled.2/RD (E)I• When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the8080 MPU and is LOW-active.The data bus is in an output status when this signal is “L”.• When connected to 6800 series MPU, this pin is treated as the “E” signal of the6800 MPU and is HIGH-active.This is the enable clock input terminal of the 6800 Series MPU.1/WR (R/W) I• When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the8080 MPU and is LOW-active.The signals on the data bus are latched at the rising edge of the /WR signal.• When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the6800 MPU and decides the access type :When R/W = “H”: Read.When R/W = “L”: Write.1C86 I This is the MPU interface selection pin.C86 = “H”: 6800 Series MPU interface.C86 = “L”: 8080 Series MPU interface.1P/S I This pin configures the interface to be parallel mode or serial mode.P/S = “H”: Parallel data input/output.P/S = “L”: Serial data input.The following applies depending on the P/S status:P/S Data/Command Data Read/Write Serial Clock“H” A0 D0 to D7 /RD, /WR X“L” A0 SI (D7) Write only SCL (D6)When P/S = “L”, D0 to D5 must be fixed to “H”./RD (E) and /WR (R/W) are fixed to either “H” or “L”.The serial access mode does NOT support read operation.1Pin Name I/O Function No. of PinsCLS I Selection pin to enable or disable the internal display clock oscillator circuit.CLS = “H” : use internal oscillator circuit .CLS = “L” : use external clock input (internal oscillator is disabled).When CLS = “L”, input the external display clock through the CL terminal.1M/S I This terminal selects the master/slave operation for the ST7565P Series chips.Master operation outputs the timing signals that are required for the LCD display,while slave operation input the timing signals required for the liquid crystal display.That synchronized the liquid crystal display system between Master and Slave.M/S = “H” Master operationM/S = “L” Slave operationM/S CLS OscillatorCircuitPowerSupplyCircuitCL FR FRS DOF“H”“H”“L”EnabledDisabledEnabledEnabledOutputInputOutputOutputOutputOutputOutputOutput“L”“H”“L”DisabledDisabledDisabledDisabledInputInputInputInputOutputOutputInputInput1CL I/O This is the display clock input terminalThe following is true depending on the M/S and CLS status.M/S CLS CL“H”“H”“L”OutputInput“L”“H”“L”InputInput1FR O This is the liquid crystal alternating current signal terminal.1 /DOF O This is the LCD blanking control terminal.1FRS O This is the output terminal for the static drive.This terminal is only enabled when the static indicator display is ONand is used in conjunction with the FR terminal.1IRS I This terminal selects the resistors for the V0 voltage level adjustment.IRS = “H”: Use the internal resistorsIRS = “L”: Do not use the internal resistors. The V0 voltage level isregulated by an external resistive voltage divider attached to the VR terminal1/HPM I This is the power control terminal for the power supply circuit for liquid crystal drive./HPM = “H”: Normal mode/HPM = “L”: High power mode1SEL3SEL2 SEL1IThese pins are DUTY selection.SEL 3 , 2 , 1 DUTY BIAS0 , 0 , 0 1/65 1/9 or 1/70 , 0 , 1 1/49 1/8 or 1/60 , 1 , 0 1/33 1/6 or 1/50 , 1 , 1 1/55 1/8 or 1/61 , 0 , 0 1/53 1/8 or 1/61, X , X ----- -----3TEST0 ~ 5 I These are terminals for IC testing.They are set to open.6LCD Driver Pins。

合集下载

零售内部指导报价2.22

零售内部指导报价2.22


商台 扬天、启天19LCD宽屏 扬天、启天20LCD宽屏 扬天、启天18.5LCD宽屏(186) 780 830 680 2400
品牌 温岭 Βιβλιοθήκη 岩 星光银IdeaPadS205XE3002G320MG(BKXX)CN
IdeaPadS205XE3002G320MG(PIXX)CN
2400
IdeaPadS205E3002G3207B(BK)CN
家电下乡分体机
家悦S5 R3 SX2 198 2G50GDU-L
3798
新圆梦F618 AX4 645 2G50GD-7B(A)
3700
4647
新品 节能机型 20LCD 下乡机
新圆梦 F415AX4631 2G50GDUJ-L 新圆梦F558 AX2 260 2G50GD-7B 新圆梦F328 PD G640 2G50DU-7B
2850
3558
新圆梦F208 CDCG530 2G25D-L(A)
2600
3198
新圆梦 H520G540 2G25DUJ-L 新圆梦 H505 E350D 2G25DUJ-L 新圆梦F118 SX2 190 2G25D-L
2600
2350
2550
2898
IdeaCentreB320 PDG630 2G50GVWTU215-7P 4200
下乡机 电视功能
IdeaCentre B320r4 G530 2G50GVWHU215-7B IdeaCentre B325r2 SX2 198 2G50GVWU20-LA IdeaCentre B520E C i3-2120 4G50GVW-D7 IdeaCentre B520r2 PD G640 4G50GVWU-L IdeaCentre B540 PD G640 4G50GVWHU-D7
ST7565液晶屏使用

ST7565液晶屏使用

ST7565使用笔记芯片简介ST7565是一款点阵液晶驱动芯片，它具有并行与串行（SPI ）两种接口，通过P/S 引脚选取：P/S=1为并行，P/S=0为串行。

这两种接口的控制信号如下：同时它具有两种接线方式：6800和8080。

通过C86引脚选取：C86=1为6800，C86=0为8080。

这两种方式的控制时序有所不同：其时序如下：复位初始化参数：P DFC r e a te !3T lwww.sc a n so f t .c om控制命令需要重点说明的是计算V0的这个命令。

该命令具体细节见下：P DFC r e a te !www.sc a n so f t .c o该命令的主要作用是计算LCD 的V0，以调节显示亮度；当增加V0以增加用户程序需要点亮点阵得亮度时，程序未要求点亮部分得亮度也相应增加。

当设置V0过大时，则显示屏显示颜色将会很深，包括程序未让其显示部分，效果就像全屏点亮一样，显示对比度很低。

当设置V0过小时，显示又会很暗，以至于显示效果不好。

所以一定要通过试验以调节V0以适合当前得LCD 。

注意：同一款LCD 驱动芯片，当玻璃片、显示区域大小等不一样时，V0设置的最佳值也将不一样，因此只有通过不断的试验以得到最佳值。

在使用ST7565时的处理流程：根据其初始化流程可知，只要对其中几项进行设置，其它保持默认值就可以了，需要设置的是：①默认的是关闭，当初始化的时候应设置成开启。

②这与外部电路连接有关。

③这与硬件连接有关。

④P DFC r e a te !3T r i a lwww.sc a n so f t .c om在使用过程中，如果向ST7565写数据，其列地址会自动增加。

当一页的数据写完后，需要设置下一页的地址，在新的一页中要重新设定列地址，即改变页地址后列地址保持不变，并不自动设置为起始列，比如，如果换页前（假设是第一页）显示列地址为10，此时发送页地址设置命令（假设设置为第二页），则此时发送的数据将从第二页第十列开始显示。

无线路由器CPU闪存内存芯片列表

无线路由器CPU闪存内存芯片列表

品牌规格cpu主频闪存/内存无线芯片参考价迅捷FWR300T+Atheros AR9132400MHZ4/32AtherosAR910390水星MWR300T+（旧款长方形的）Atheros AR9132400MHZ4/32 V1版新款可能有缩水AtherosAR910390TP-LINK TL-WR941N Atheros AR9132400MHZ4/32AtherosAR9103D-LINK DIR618RealtekRTL8196B 400MHZ2/16RealtekRTL8192SE华硕RT-N56U RalinkRT3662F+RT3092500MHZ8/128主芯片集成TOTOLINK N5004BroadcomBCM4718A533 MHZ4/16主芯片集成贝尔金畅享版BroadcomBCM4718A533 MHZ8/64主芯片集成华硕RT-N16BroadcomBCM4718A533 MHZ32/128主芯片集成型号&版本CPU主频无线芯片RAMSize Flash天线数TP-LINK/MW/FWTL-WR843N AR9341200mhz32M4MTL-WR841N V8AR9341200mhz16M4M2 TL-WR841N V7AR7241-AH1A360AR928732M4M2 TL-WR740N V4AR7240400AR928532M4M1 TL-WR2543ND AR7242400AR938064M8MTL-WR1041N AR9342-AL1A550AR832732M4MTL-WR800N AR934120016MTL-WA901NDV2.xAR9132400AR541632M4MTL-WA901NDV1.xAR7240400AR928532M4MTL-WA801NDv1.1AR724x查不了AR9238-AL1A 32M4MTL-WA701ND v1AR724040032M4M MW310R V1AR934120016M4M3MW300R V4AR934120016M2M MW300R V3AR934120016M4M2 MW300r v2AR72416802 TL-WDR4310AR9344 533AR9580128M8MTL-WDR7500QCA9880[AC]600QCA9558[N]128MMW150R V8.4AR9331400D-LINKDir615-1 F2RTL8196B 400RTL8192SEDIR615 C1AR9130400AR8216DIR615L J1RTL8196C 400RTL8192SEDIR600NW A1RT3050F320腾达W811R RT3050F320N300R BCM5357C0533N308R BCM5357500N309R BCM5357500N3000BCM5357500W311R_2011RT3050F320W311R V2BCM5356333W311R V3BCM5356333A5S RT5350F360A6RT5350F360N4RT5350F360W268R RT3050F320W307R RT2880F266W837R BCM5357500磊科NW614RTL8196C400NW714RTL8196C400RTL8192CENW715P BCM5357B0533超频NW736BCM5357200NW735BCM5357200NR235W BCM5357C0300超频NW716RTL8196C400RTL8192CENW762NW765BCM5358500BCM4323NW705+ V1.1RTL8196C400RTL8188RENW705同上NW604不明牌子400 TP-link(以下均是)TL-R860+ v2.08口有线路由9vcpu 88E6218-LG01 150MHZis42s16400B-7TL 内存64MBEN29LV160AB 闪存2MBS29AL908D70TE102 不明芯片TL-WR641G Athreos AR2316 + Marvell 88E6060 TL-WR641G+ Athreos AR2318 + Marvell 88E6060 TL-WR642G Athreos AR2316 + Marvell 88E6060 TL-WR642G+ Athreos AR2318 + Marvell 88E6060 TL-WN610G Athreos AR2414TL-WN620G Athreos AR5523TL-WN650G Athreos AR2414TL-WN651G Athreos AR2414TL-WN660G Athreos AR2414TL-WN612AG Athreos AR5414TL-WN652AG Athreos AR5414TL-WN653AG Athreos AR5414TL-WN662AG Athreos AR5414TL-WR541G Athreos AR2413 + Marvell 801012 TL-WR541G+ Athreos AR2317 + Marvell 88E6060 TL-WR542G Athreos AR2317 + Marvell 88E6060 TL-WA501G Athreos AR2315 + Realtek RTL8201 TL-WN510G Athreos AR2413TL-WN550G Athreos AR2413TL-WN551G Athreos AR2413TL-WN321G Ralink RT2571WTL-WN321G Ralink RT2571WTL-WN560G Athreos AR2413TL-WN512AG Athreos AR5413TL-WN552AG Athreos AR5413TL-WN553AG Athreos AR5413TL-WN562AG Athreos AR5413TL-ANT2402A N/ATL-ANT2405C N/ATL-ANT2406A N/ATL-ANT2409A N/ATL-ANT2414A N/ATD-8610 Annex A) Broadcom BCM6338 + BCM6301TD-8610 Annex B) Broadcom BCM6338 + BCM6301TD-8810 (Annex A) Broadcom BCM6338 + BCM6301TD-8810 (Annex B) Broadcom BCM6338 + BCM6301TD-8811 (Annex A) Broadcom BCM6338 + BCM6301TD-8811 (Annex B) Broadcom BCM6338 + BCM6301TD-8840 (Annex A) Broadcom BCM6338 + BCM6301TD-8840 (Annex B) Broadcom BCM6338 + BCM6301TD-8841 (Annex A) Broadcom BCM6338 + BCM6301TD-8841 (Annex B) Broadcom BCM6338 + BCM6301TL-W8910G Atheros AR2413TL-W8920G Atheros AR2414TL-R402M Marvell 88E6218TL-R460 Marvell 88E6218TL-R860 Marvell 88E6218+Marvell 88E6060(Switch)TL-R860+ Marvell 88E6218 is42s16400B-7TL 内存64MB EN29LV160AB 闪存2MB S29AL908D70TE102不明芯片TL-R480T Intel FWIXP420BB (CPU) + Marvell 88E6063 (Switch)TL-R4000 Intel FWIXP420BB (CPU) + Marvell 88E6063 (Switch)TL-R480T+ Intel FWIXP420BB (CPU) + Marvell 88E6063 (Switch)TL-R488T Intel FWIXP425BD (CPU) + Marvell 88E6063 (Switch)TL-R4000+ Intel FWIXP425BD (CPU) +Marvell 88E6063 (Switch)TL-SG3109 Marvell 88E6185 (MAC) + 88E1145 (PHY) + 88E6218 (CPU)TL-SG3216 Marvell 98DX160 (MAC) + 88E1145 + 88E1111 + 88E1112 (PHY) + 88E6218 (CPU)TL-SG3224 Marvell 98DX240 (MAC) + 88E1145 + 88E1111 + 88E1112 (PHY) + 88E6218 (CPU)TL-SG3248 Marvell 98DX26x (MAC) + 88E1145 + 88E1111 + 88E1112 (PHY) + 88E6218 (CPU)TL-SL3428 Marvell 88E6185 + 88E6095 (MAC) + 88E1111 (PHY) + 88E6218 (CPU)TL-SL3452 Marvell 88E6185 + 88E6095 (MAC) + 88E1111 (PHY) + 88E6218 (CPU)TL-SG2109WEB Marvell 88E6182 (MAC) + 88E1145 (PHY) + 88E6218 (CPU)TL-SG2216WEB Marvell 98DX162 (MAC) + 88E1145 + 88E1111 + 88E1112 (PHY) + 88E6218 (CPU)TL-SG2224WEB Marvell 98DX242 (MAC) + 88E1145 + 88E1111 + 88E1112 (PHY) + 88E6218 (CPU)TL-SG2248WEB Marvell 98DX262 (MAC) + 88E1145 + 88E1111 + 88E1112 (PHY) + 88E6218 (CPU)TL-SL2210WEB Marvell 88E6092 (MAC) + 88E1111 (PHY) + 88E6218 (CPU)TL-SL2218WEB Marvell 88E6092 (MAC) + 88E1111 (PHY) + 88E6218 (CPU)TL-SL2428WEB Marvell 88E6182 + 88E6092 (MAC) + 88E1111 (PHY) + 88E6218 (CPU)TL-SL2452WEB Marvell 88E6182 + 88E6092 (MAC) + 88E1111 (PHY) + 88E6218 (CPU)TL-SG1005D Vitesse VSC7385TL-SG1008D Vitesse VSC7388TL-SG1008 Vitesse VSC7388TL-SG1016 Vitesse VSC7389 (MAC) + VSC8538 (PHY)TL-SG1016 Marvell 98DX161 (MAC) + 88E1149 (PHY)TL-SG1016D Marvell 98DX161 (MAC) + 88E1149 (PHY)TL-SG1024 Vitesse VSC7390 (MAC) + VSC8538 (PHY)TL-SG1024 Marvell 98DX241 (MAC) + 88E1149 (PHY)TL-SL1109 Realtek RTL8310 (MAC) + RTL8208B (PHY)TL-SL1117 Realtek RTL8318 (MAC) + RTL8208B (PHY)TL-SL1226 Realtek RTL8326(MAC)+ RTL8208-VF(PHY)+ Cicada CIS8201(PHY) TL-SL1351 Marvell 88E6182 + 88E6092 (MAC) + 88E1111 (PHY) + 88E6218 (CPU) TL-SF1005D Realtek RTL8305SCTL-SF1005D Marvell 88E6060TL-SF1008D Realtek RTL8309SBTL-SF1016D Realtek RTL8309SBTL-SF1016 Realtek RTL8316B (MAC) + RTL8208(PHY)TL-SF1016 Realtek RTL8316B (MAC) + RTL8208(PHY)TL-SF1024 Realtek RTL8324 (MAC) + RTL8208B (PHY)TL-SF1048 Realtek RTL8326 (MAC) + RTL8208-VF(PHY)TL-SM201CM Altima AC101TL-SM201CS Altima AC101TL-SM311LM N/ATL-SM311LS N/ATR-966D Realtek RTL8305SCTR-965DA Realtek RTL8305SCTR-965DB Realtek RTL8305SCTR-932D Realtek RTL8305SCTR-962D Realtek RTL8305SCTG-3269 Realtek RTL8169SCTG-3201 Marvell 88E8001TF-3239D Realtek RTL8139DTF-3239DL Realtek RTL8139DTF-5239 Realtek RTL8139CLTM-IP5600 Motorola PCI 3 (Si3052+Si3007)TM-EC5658V Intel MD5660 + MD4450 + MD1724。

Lenovo ThinkAgile HX7521 Certified Node for SAP HA

Lenovo ThinkAgile HX7521 Certified Node for SAP HA

Lenovo ThinkAgile HX7521 Certified Node forSAP HANA (Xeon SP Gen 1)Product Guide (withdrawn product)Lenovo ThinkAgile HX Certified Nodes for SAP HANA are designed for deploying industry-leading hyperconvergence software from Nutanix on Lenovo enterprise platforms that feature the Intel Xeon Processor Scalable Family.The ThinkAgile HX Certified Nodes for SAP HANA deliver fully validated and integrated Lenovo hardware and firmware, certified and preloaded with Nutanix software. Nutanix brings the benefits of web-scale technologies to enterprise applications through enterprise storage, data protection, infrastructure resilience, management and analytics, and security.The ThinkAgile HX7521 Certified Node for SAP HANA is a 2U rack-mount system that supports two processors, up to 3 TB of 2666 MHz TruDDR4 memory, 24x SFF hot-swap drive bays with an extensive choice of SAS/SATA SSDs and HDDs, and flexible network connectivity options with 1/10 GbE RJ-45,10 GbE SFP+, and 10/25 GbE SFP28 ports.The ThinkAgile HX7521 Certified Node for SAP HANA is certified by SAP for deploying SAP HANA solutions on hyperconverged infrastructure (HCI) in production environments.The ThinkAgile HX7521 Certified Node for SAP HANA is shown in the following figure.Figure 1. Lenovo ThinkAgile HX7521 Certified Node for SAP HANADid you know?The ThinkAgile HX Certified Nodes for SAP HANA are built on industry-leading Lenovo ThinkSystem servers that feature enterprise-class reliability, management, and security.The ThinkAgile HX Certified Nodes for SAP HANA deliver fully validated and integrated hardware and firmware that is certified with Nutanix software.Click here to check for updatesFigure 2. ThinkAgile HX7521 Certified Node for SAP HANA front viewThe front of the ThinkAgile HX7521 Certified Node for SAP HANA includes the following components: 20x SAS/SATA and 4x AnyBay, or 12x SAS/SATA and 4x AnyBay 2.5-inch hot-swap drive bays One VGA portOne USB 2.0 port with XClarity Controller accessOne USB 3.0 portA Power buttonStatus LEDsFigure 3. ThinkAgile HX7521 Certified Node for SAP HANA rear viewThe rear of the ThinkAgile HX7521 Certified Node for SAP HANA includes the following components: Up to six PCIe expansion slots (2 reserved for SAS HBAs)One LOM card slotOne 1 GbE port for XClarity ControllerOne VGA portTwo USB 3.0 portsTwo hot-swap power suppliesMemoryThe ThinkAgile HX7521 Certified Node for SAP HANA for SAP HANA supports Lenovo TruDDR4 memory. TruDDR4 memory uses the highest-quality components sourced from Tier 1 DRAM suppliers and only memory that meets strict requirements is selected. It is compatibility tested and tuned to maximize performance and reliability.The ThinkAgile HX7521 Certified Node for SAP HANA supports 12 or 24 DIMMs. Each processor has six memory channels, and there are two DIMM slots per channel.1.25m Cat6 Green Cable 00WE131AVFY 1.5m Cat6 Green Cable 00WE135AVFZ 3m Cat6 Green Cable 00WE139AVG010m Cat6 Green Cable 90Y3718A1MT 25m Cat6 Green Cable90Y3727A1MWDescriptionPart number Feature codeThe following table lists transceivers and cables for the 10 GbE SFP+ ports.Table 11. Transceivers and cables for 10 GbE SFP+ portsDescriptionPart numberFeature code10 GbE SFP+ SR transceivers for 10 GbE SFP+ ports Lenovo 10GBASE-SR SFP+ Transceiver 46C34475053Lenovo 10GBASE-LR SFP+ Transceiver 00FE331B0RJOptical cables for 10 GbE SFP+ SR transceivers Lenovo 0.5m LC-LC OM3 MMF Cable 00MN499ASR5Lenovo 1m LC-LC OM3 MMF Cable 00MN502ASR6Lenovo 3m LC-LC OM3 MMF Cable 00MN505ASR7Lenovo 5m LC-LC OM3 MMF Cable 00MN508ASR8Lenovo 10m LC-LC OM3 MMF Cable 00MN511ASR9Lenovo 15m LC-LC OM3 MMF Cable 00MN514ASRA Lenovo 25m LC-LC OM3 MMF Cable00MN517ASRB Passive SFP+ DAC cables for 10 GbE SFP+ ports Lenovo 0.5m Passive SFP+ DAC Cable 00D6288A3RG Lenovo 1m Passive SFP+ DAC Cable 90Y9427A1PH Lenovo 1.5m Passive SFP+ DAC Cable 00AY764A51N Lenovo 2m Passive SFP+ DAC Cable 00AY765A51P Lenovo 3m Passive SFP+ DAC Cable 90Y9430A1PJ Lenovo 5m Passive SFP+ DAC Cable 90Y9433A1PK Lenovo 7m Passive SFP+ DAC Cable00D6151A3RHActive SFP+ DAC cables for 10 GbE SFP+ ports Lenovo 1m Active DAC SFP+ Cable 00VX111AT2R Lenovo 3m Active DAC SFP+ Cable 00VX114AT2S Lenovo 5m Active DAC SFP+ Cable00VX117AT2TSFP+ active optical cables for 10 GbE SFP+ ports Lenovo 1m SFP+ to SFP+ Active Optical Cable 00YL634ATYX Lenovo 3m SFP+ to SFP+ Active Optical Cable 00YL637ATYY Lenovo 5m SFP+ to SFP+ Active Optical Cable 00YL640ATYZ Lenovo 7m SFP+ to SFP+ Active Optical Cable 00YL643ATZ0Lenovo 15m SFP+ to SFP+ Active Optical Cable 00YL646ATZ1Lenovo 20m SFP+ to SFP+ Active Optical Cable00YL649ATZ2The following table lists transceivers and cables for the 25 GbE SFP28 ports. Table 12. Transceivers and cables for 25 GbE SFP28 portsDescription Part number Feature code25 GbE SFP28 SR transceivers for 25 GbE SFP28 portsLenovo 25GBASE-SR SFP28 Transceiver7G17A03537AV1B Optical cables for 25 GbE SFP28 SR transceiversLenovo 0.5m LC-LC OM3 MMF Cable00MN499ASR5 Lenovo 1m LC-LC OM3 MMF Cable00MN502ASR6 Lenovo 3m LC-LC OM3 MMF Cable00MN505ASR7 Lenovo 5m LC-LC OM3 MMF Cable00MN508ASR8 Lenovo 10m LC-LC OM3 MMF Cable00MN511ASR9 Lenovo 15m LC-LC OM3 MMF Cable00MN514ASRA Lenovo 25m LC-LC OM3 MMF Cable00MN517ASRB Passive copper cables for 25 GbE SFP28 portsLenovo 1m Passive 25G SFP28 DAC Cable7Z57A03557AV1W Lenovo 3m Passive 25G SFP28 DAC Cable7Z57A03558AV1X Lenovo 5m Passive 25G SFP28 DAC Cable7Z57A03559AV1Y Active optical cables for 25 GbE SFP28 portsLenovo 3m 25G SFP28 Active Optical Cable7Z57A03541AV1F Lenovo 5m 25G SFP28 Active Optical Cable7Z57A03542AV1G Lenovo 10m 25G SFP28 Active Optical Cable7Z57A03543AV1H Lenovo 15m 25G SFP28 Active Optical Cable7Z57A03544AV1J Lenovo 20m 25G SFP28 Active Optical Cable7Z57A03545AV1KPower supplies and cablesThe ThinkAgile HX7521 Certified Nodes for SAP HANA ship with two 1100W (230V/115V) Platinum hot-swap power supplies listed in the following table.Table 13. Power suppliesDescription Featurecode QuantityThinkSystem 1100W (230V/115V) Platinum Hot-Swap Power Supply AVWF2The ThinkAgile HX7521 Certified Nodes for SAP HANA ship with or without power cords depending on the selected option. The following table lists the rack power cables and line cords that can be ordered for the ThinkAgile HX7521 Certified Nodes for SAP HANA.Table 14. Power cablesDescription PartnumberFeaturecodeRack power cables1.0m, 13A/100-250V, C13 to IEC 320-C14 Rack Power Cable4L67A08367B0N5 1.2m, 16A/100-250V, 2 Short C13s to Short C20 Rack Power Cable47C2491A3SW1.5m, 13A/100-250V, C13 to IEC 320-C14 Rack Power Cable4L67A08368B0N62.0m, 13A/125V-10A/250V, C13 to IEC 320-C14 Rack Power Cable4L67A083696570 2.5m, 16A/100-250V, 2 Long C13s to Short C20 Rack Power Cable47C2492A3SX 2.8m, 13A/125V-10A/250V, C13 to IEC 320-C14 Rack Power Cable4L67A083706400 2.8m, 16A/100-250V, 2 Short C13s to Long C20 Rack Power Cable47C2493A3SY 4.1m, 16A/100-250V, 2 Long C13s to Long C20 Rack Power Cable47C2494A3SZ 4.3m, 13A/125V-10A/250V, C13 to IEC 320-C14 Rack Power Cable4L67A083716583 Line cordsArgentina 2.8m, 10A/250V, C13 to IRAM 2073 Line Cord39Y79306222 Argentina 4.3m, 10A/250V, C13 to IRAM 2073 Line Cord81Y23846492 Australia/New Zealand 2.8m, 10A/250V, C13 to AS/NZS 3112 Line Cord39Y79246211 Australia/New Zealand 4.3m, 10A/250V, C13 to AS/NZS 3112 Line Cord81Y23836574 Brazil 2.8m, 10A/250V, C13 to NBR 14136 Line Cord69Y19886532 Brazil 4.3m, 10A/250V, C13 to NBR14136 Line Cord81Y23876404 China 2.8m, 10A/250V, C13 to GB 2099.1 Line Cord39Y79286210 China 4.3m, 10A/250V, C13 to GB 2099.1 Line Cord81Y23786580 Denmark 2.8m, 10A/250V, C13 to DK2-5a Line Cord39Y79186213 Denmark 4.3m, 10A/250V, C13 to DK2-5a Line Cord81Y23826575 Europe 2.8m, 10A/250V, C13 to CEE7-VII Line Cord39Y79176212 Europe 4.3m, 10A/250V, C13 to CEE7-VII Line Cord81Y23766572 India 2.8m, 10A/250V, C13 to IS 6538 Line Cord39Y79276269 India 4.3m, 10A/250V, C13 to IS 6538 Line Cord81Y23866567 Israel 2.8m, 10A/250V, C13 to SI 32 Line Cord39Y79206218 Israel 4.3m, 10A/250V, C13 to SI 32 Line Cord81Y23816579 Italy 2.8m, 10A/250V, C13 to CEI 23-16 Line Cord39Y79216217 Italy 4.3m, 10A/250V, C13 to CEI 23-16 Line Cord81Y23806493 Japan 2.8m, 12A/125V, C13 to JIS C-8303 Line cord46M2593A1RE Japan 2.8m, 12A/250V, C13 to JIS C-8303 Line Cord4L67A083576533 Japan 4.3m, 12A/125V, C13 to JIS C-8303 Line Cord39Y79266335 Japan 4.3m, 12A/250V, C13 to JIS C-8303 Line Cord4L67A083626495 Korea 2.8m, 12A/250V, C13 to KS C8305 Line Cord39Y79256219 Korea 4.3m, 12A/250V, C13 to KS C8305 Line Cord81Y23856494 South Africa 2.8m, 10A/250V, C13 to SABS 164 Line Cord39Y79226214 South Africa 4.3m, 10A/250V, C13 to SABS 164 Line Cord81Y23796576Switzerland 2.8m, 10A/250V, C13 to SEV 1011-S24507 Line Cord 39Y79196216Switzerland 4.3m, 10A/250V, C13 to SEV 1011-S24507 Line Cord 81Y23906578Taiwan 2.8m, 10A/250V, C13 to CNS 10917-3 Line Cord 81Y23756317Taiwan 2.8m, 15A/125V, C13 to CNS 10917-3 Line Cord 81Y23746402Taiwan 4.3m, 10A/250V, C13 to CNS 10917-3 Line Cord 81Y23896531Taiwan 4.3m, 15A/125V, C13 to CNS 10917-3 Line Cord 81Y23886530United Kingdom 2.8m, 10A/250V, C13 to BS 1363/A Line Cord 39Y79236215United Kingdom 4.3m, 10A/250V, C13 to BS 1363/A Line Cord 81Y23776577United States 2.8m, 10A/250V, C13 to NEMA 6-15P Line Cord 46M2592A1RF United States 2.8m, 13A/125V, C13 to NEMA 5-15P Line Cord 00WH5456401United States 4.3m, 10A/250V, C13 to NEMA 6-15P Line Cord 4L67A083616373United States 4.3m, 13A/125V, C13 to NEMA 5-15P Line Cord4L67A08360AX8ADescriptionPart number Feature code Rack installationThe ThinkAgile HX7521 Certified Nodes for SAP HANA ship with a rail kit. The following table lists the rail kit options that are available for selection.Table 15. Rack kit selection optionsDescription Feature codeQuantity (min / max)4-post rail kitsThinkSystem Tool-less Slide RailAXCA 0 / 1ThinkSystem Tool-less Slide Rail Kit with 2U CMA AXCH0 / 1Lockable front bezelThinkSystem 2U Security BezelAURX0 / 1Configuration note: One of the rail kits is required for selection.The following table summarizes the rail kit features and specifications.Table 16. Rail kit features and specifications summaryFeature Tool-less Slide RailWithout CMA With 2U CMA CMA Not included IncludedRail length 730 mm (28.74 in.)807 mm (31.8 in.)Rail typeFull-out slide (ball bearing)Tool-less installation Yes In-rack maintenance Yes 1U PDU support Yes 0U PDU support Limited*Rack type IBM and Lenovo 4-post, IEC standard-compliant Mounting holesSquare or roundTrademarksLenovo and the Lenovo logo are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. A current list of Lenovo trademarks is available on the Web athttps:///us/en/legal/copytrade/.The following terms are trademarks of Lenovo in the United States, other countries, or both:Lenovo®AnyBay®Lenovo ServicesThinkAgile®ThinkSystem®TruDDR4XClarity®The following terms are trademarks of other companies:Intel® and Xeon® are trademarks of Intel Corporation or its subsidiaries.Linux® is the trademark of Linus Torvalds in the U.S. and other countries.Microsoft®, PowerShell, Windows PowerShell®, and Windows® are trademarks of Microsoft Corporation in the United States, other countries, or both.Other company, product, or service names may be trademarks or service marks of others.。