友达B140XW01 V8 PDF

AS-1H1V-WP Technical SpecificationsThe Intelix AS-1H1V-WP is a two-gang, Decora-style wallplate designed to be the primary PC interface for classrooms, boardrooms, and conference centers. It features VGA + Audio to HDMI conversion with VGA scaling up to 1920x1200 and an HDMI input.The AS-1H1V-WP utilizes HDBaseT technology to extend the digital output up to 70 meters away using solid core shielded Category 5e or greater cable. This transmitter device is compatible with several Intelix HDBaseT receivers, but is designed to work primarily with the DIGI-HD60C-R. The unit features multiple EDID modes to eliminate user confusion, and incompatible video formats.The AS-1H1V can be powered from the rear panel or by Power over HDBaseT (PoH), including midspan injectors that support Power over Ethernet (PoE) Alternative A or Alternative B. Built-in surge protection and diagnostic LEDs ensure hassle-free and robust installations. The AS-1H1V-WP also features a customizable power management system, which will put the unit into a low power state after no video for 30 minutes or being inactive for 3 hours by default. When using the local power input, 12V DC is available for other devices on the power output connections on the rear of the device.The AS-1H1V-WP will detect which input has an active video input, and switch to that input – if both inputs are active, the “last in” will be selected. There are additional contact closure inputs provided on the rear of the unit to allow third party control. RS232 control of the AS-1H1V-WP can be accomplished by connecting to the RS232 port on a compatible receiver, such as a DIGI-HD60C-R, or through a direct connection on the RS232 input of the device.The AS-1H1V-WP can be programmed to control the connected display. The display manufacturer’s RS232 commands can be entered into the AS-1H1V-WP with the use of Intelix Display Control software. This allows display power and input to be automatically controlled based on video activity, eliminating the need for a third party control system in many installations.AS-1H1V-WP Technical SpecificationsHDMI and VGA Auto-Switching WallplateRev 160804AS-1H1V-WP Technical SpecificationsAS-1H1V-WP Technical Specifications Input/Output ConnectionsHDMI Input One (1) HDMI Type A ReceptacleVGA Input One (1) PC Video HD-15-F ReceptacleAnalog Audio One (1) 3.5 mm TRS ReceptacleHDBaseT Port One (1) 8P8C port (Shielded RJ45)Power One (1) 2-pin Removable Terminal Block ConnectorRS232 Port with 12V DC Output One (1) 4-pin Removable Terminal Block ConnectorContact Closures One (1) 4-pin Removable Terminal Block ConnectorFirmware Port One (1) USB Type B Micro ReceptacleSupported Audio, Video and ControlVideo Resolutions SMPTE: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, UHD/30 (HDMI only)VESA: Resolutions up to 1920x1200Color Depth: 24, 30, 36, 48bitVGA Scaling Resolutions (60 Hz)1024x768, 1400x1050, 1600x1200, 1280x800, 1360x768, 1920x1200, 720p, 1080pMaximum Video Compatibility at 70 m Deep Color 36/30/24 Bit at 1080pMaximum Video Compatibility at 40 m Deep Color 48 Bit at 1080p, 3D (HDMI Input), UHD/30Video Compliance HDMI 1.4 and HDCP 1.4Embedded Audio Up to PCM 8 channel, Dolby Digital TrueHD, and DTS-HD Master AudioAnalog Audio Analog stereo line-level (Converted to 2ch 24bit PCM 48kHz)ARC (Audio Return Channel)NoHEC (HDMI Ethernet Channel)NoCEC (Consumer Electronics Control)Yes (HDMI Pass-through Only)Baud Rate (Wall plate control)2400, 4800, 9600 (default), 19200, 38400, 57600, 115200Supported Baud Rates (Display Control)2400, 4800, 9600, 19200, 38400, 57600, 115200HDBaseT Signal CharacteristicsMaximum Distance70 m (229 ft)Cable Requirements Continuous solid core Category 5e or greater with TIA/EIA-568B crimp pattern (no couplers in-line)Bandwidth10.2 GbpsHDBaseT Chipset VS010TXChassis and EnvironmentalConstruction Alumininum HousingDimensions (H x W x D)104 mm x 89 mm x 51 mm (4.09 in x 3.50 in x 2.01 in)Shipping Weight0.68 kg (11.5 lbs.)Operating Temperature0° to +40° C (+32° to +104° F)Operating Humidity20% to 90%, Non-condensingStorage Temperature-10° to +60° C (+14° to +140° F)Storage Humidity20% to 90%, Non-condensingPower and RegulatoryPower Supply12V DC 2A or 48V DC PoH (Power over HDBaseT)Power Output Port12V DC, 500 mAPower over Ethernet (PoE) Compatibility802.3af Alternative A and Alternative BPower Consumption10 wattsDefault Automatic Standby Mode30 minutes no signalESD Protection16kVRegulatory CE, RoHSOtherWarranty 2 yearsDiagnostic Indicators HDCP, Link, VGA, and HDMIReset Switch MicroswitchAvailable Models AS-1H1V-WP-W (White Faceplate and Painted Insert), AS-1H1V-WP-B (Black Faceplate and Painted Insert) Included Accessories Installation Guide, Power Supply, Two (2) 4-pin Removable Screw Terminals, RS232 cable (3-pin to DE9), 2-pinRemovable Screw Terminal, USB Programming CableHDBaseT Receiver (A/V, PoE, Control) Compatibility DIGI-HD60C-R, DIGI-HDX-R, FLX-64, DIGI-BSR-4KHDBaseT Receiver (A/V, Control) Compatibility FLX-BI4HDBaseT Receiver (A/V and PoE) Compatibility DIGI-HD60-RDistances and picture quality may be affected by cable grade, cable quality, source and destination equipment, RF and electrical interference, and cable patches.。

Dell UltraSharp U3818DW 显示器用户指南管制型号： U3818DW注、注意和警告注：“注”表示可以帮助您更好使用计算机的重要信息。

注意： “注意”表示如果不遵循说明操作可能会损坏硬件或导致数据丢失。

警告： “警告”表示可能会造成财产损失、人身伤害或死亡。

____________________版权所有 © 2017-2020 Dell Inc. 保留所有权利。

本产品受美国和国际版权法和知识产权法的保护。

Dell TM和 Dell 标志为在美国和/或其它司法管辖地的商标。

本文中提到的所有其它标志和名称可能是其它公司的商标。

2020 - 06Rev. A05目录关于本显示器. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5包装物品 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5产品特性 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7识别零部件及控制装置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8显示器规格 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12即插即用功能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19通用串行总线 (USB) 接口 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19液晶显示器质量和像素规定 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21维护指导 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21设置您的显示器. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22连接支架 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22连接显示器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25设置电缆 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28拆卸显示器支架 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29墙面安装（选配） . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29操作显示器. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31打开显示器电源 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31使用前面板控制部件 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31目录|3使用屏幕显示 (OSD) 菜单. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33设置最大分辨率 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49设置 KVM 切换开关. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50设置自动 KVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53使用倾斜、旋转和垂直展开功能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55故障排除. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56自检 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56内置诊断功能 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57始终开启 USB Type-C 充电 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57常见问题 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58产品特定问题 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59通用串行总线 (USB) 特定问题 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60扬声器特定问题 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60附录. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 FCC 声明（仅针对美国）和其它管制信息 . . . . . . . . . . . . . . . . . . . . . . . 61中国能源效率标识 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61联系 Dell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614|目录关于本显示器|5关于本显示器包装物品您的显示器配有以下部件。

Discover-MO:) 系列产品之STM32F4DISCOVERY扩展板DM-STF4BB用户手册深圳市英蓓特科技有限公司DM-STF4BB扩展板♦基于ST原厂评估套件STM32F4DISCOVERY的扩展板。

♦支持3.5寸工业级LCD触摸屏，4线触摸模块。

♦支持130万像素OV9655 Camera模块。

♦1路10/100M以太网接口。

♦1路3线RS232电平接口（DB9公头接口）。

♦5路3线TTL电平UART，通过排针引出。

♦支持uC/OS-Ⅱ_v2.86 & uC/GUI_v3.90a,并提供BSP源码（如用于商业,需申请授权）♦支持FatFs_vR0.08a 文件系统(用于SD卡的文件系统)♦支持LwIP_v1.3.2协议栈版权◆Discover-MO:) , DM-STF4BB, Devkit407由深圳英蓓特科技有限公司授权。

◆STM32F407, STM32F4DISCOVERY由意法半导体（ST）授权。

◆Microsoft，MS-DOS，Microsoft Windows XP 由微软授权。

重要申明Embest拥有对该文档的所有权和使用权。

本文档上的信息受版权保护。

除非经特别许可，否则未事先经过Embest的书面许可，不得以任何方式和形式来修改、分发和复制本文档的任何部分。

版本更新记录：版本日期描述V1.0 2012-08-15 初始版本联系我们：如果您想订购英蓓特的DM-STF4BB或其他产品，请与市场部联系：电话：*************/25631357/25635656传真：*************邮箱：****************如果您想获得英蓓特的技术支持，请与技术支持联系：电话：*************邮箱：*****************网址：地址：深圳市罗湖区太宁路85号罗湖科技大厦405室目录DM-STF4BB扩展板 (2)1概述 (9)1.1 产品简介 (9)1.2 产品构成 (9)1.3 产品示意图 (10)1.4 应用领域 (12)1.5 系统结构框图 (12)1.6 产品硬件特性 (14)1.7 产品软件特性 (15)2硬件系统 (17)2.1 CPU (17)2.2 硬件接口 (18)2.2.1 RS232串行接口 (18)2.2.2 Ethernet接口 (18)2.2.3 Micro SD卡接口 (19)2.2.4 LCD接口 (19)2.2.5 扩展接口 (21)2.2.6 Camera接口 (22)2.3 引脚复用 (24)2.4 硬件尺寸 (27)3搭建开发环境 (28)3.1 硬件环境 (28)3.2 软件环境 (28)3.3 PC机环境配置 (29)3.3.1 超级终端配置 (29)3.3.2 网络配置 (32)4基本外设例程 (35)4.1 USART实验 (35)4.2.1 FatFs例程 (36)4.2.2 uSDCard例程 (37)4.3 LCD实验 (38)4.3.1 LCD_35T例程 (38)4.3.2 LCD_Touch例程 (39)4.4 DCMI实验 (40)4.5 Ethernet实验 (41)4.5.1 Standalone/httpserver例程 (41)4.5.2 Standalone/tcp_echo_client例程 (44)4.5.3 Standalone/tcp_echo_server例程 (47)4.5.4 Standalone/udp_echo_client例程 (49)4.5.5 Standalone/udp_echo_server例程 (51)4.5.6 FreeRTOS/httpserver_netconn例程 (54)4.5.7 FreeRTOS/httpserver_socket例程 (56)4.5.8 FreeRTOS/udptcp_echo_server_netconn例程 (56)4.6 USB实验 (57)4.6.1 USB_Device_Examples/DFU例程 (58)4.6.2 USB_Device_Examples/MSC例程 (61)4.6.3 USB_Device_Examples/VCP例程 (62)4.6.4 USB_Host_Examples/HID例程 (67)4.6.5 USB_Host_Examples MSC例程 (69)5扩展例程 (73)5.1 STM32F4xx-uCOS-II (73)5.2 STM32F4xx-uCOSII-uCGUI (73)5.3 STM32F4xx_FPU_fft_example (74)6功能测试 (75)6.1 USART测试 (75)6.2 SDIO测试 (75)6.4 DCMI测试 (75)6.5 Ethernet测试 (75)6.6 USB测试 (75)7产品清单 (76)8技术支持与保修 (77)8.1 技术支持服务 (77)8.2 保修服务条款 (77)8.3 液晶屏幕基本使用保养知识 (78)8.4 增值服务 (78)1 概述1.1 产品简介DM-STF4BB是深圳市英蓓特科技有限公司推出的一款基于STM32F4DISCOVERY的扩展板，它将联合STM32F4DISCOVERY一起组成Embest的Devkit407评估板。

Primed to perform.Configured for your business.ASUS ExpertBook B1 is tailored for business, making it the smart choice for ambitious startups, established education organizations and growing firms of all sizes. It boasts high performance, military-grade durability and extensive customization to empower your business. It’s also engineered to confidently handle whatever tasks come your way, with a full set of I/O ports, speedy WiFi 6 and cutting-edge AI noise-canceling technology. ExpertBook B1 streamlines your workflow to keep you productive.Primed to performThe ultimate performance boostExclusive Performance Boost technology achieves the bestlaptop performance and agility by tuning the internal thermals,delivering the sterling performance needed to get the job done1.Crystal-clear conferencing audioInnovative ASUS AI noise-canceling technology enables superiorcalls. The AI Noise-Canceling Speaker feature filters out all ambientnoise apart from human speech — so you’ll hear what everyoneelse is saying.Freewheeling mobilityExpertBook B1 is surprisingly light for a business laptop, weighingas little as 1.72 kg, so it’s comfortable to carry anywhere2.Extensive connectivitySupport for the latest Thunderbolt™ 4 standard with USB4 andDisplayPort means built-in power delivery, fast charging, displayconnectivity and extreme-speed data transfers. It also has bothUSB 3.2 Gen 2 and USB 2.0 Type-A, HDMI 2.0, Ethernet and amicroSD card slot.Commercial-grade durability and securityMilitary-grade constructionThe chassis design combines additional structural enhancementsto meet the rigors of daily use. These include a resilient aluminum-alloy upper cover, an internal keyboard bracket and protectivefoam protects the hard drive from bumps and shocks3.One-touch, fingerprint loginA sensor integrated into the power button offers biometricsecurity that’s as easy as it is effective. All you need to do to switchon and log is press the power button – eliminating the need fordifficult-to-remember passwords or PINs4,5.Webcam shield for protecting privacyA physical cover provides instant privacy when the lens is not inuse. Just slide it open to make video calls or recordings, and backacross when you’re done4.Trusted Platform Module (TPM) securityThe embedded TPM 2.0 chip securely stores authenticationinformation used by software, such as passwords or encryptionkeys, to protect important data and transactions – keeping theinformation away from the eyes of would-be attackers4.| B1500Immersive NanoEdge display with 90% screen to body ratioFingerprint sensor that’s integrated into the power bottom for biometric security1.5mm long-travel keys provide for tactile, responsive keystrokesComprehensive I/Oconnectivity for a diverse array of business peripheralsSolid construction with Militarygrade reliabilitySPECIFICATIONS |1. To enable Performance Mode, please keep the laptop plugged in for the best performance, set the Windows power option as ASUS Recommended Mode, and select Performance Mode in the MyASUS software.2. Product weight may vary according to device configuration.3. The testing data includes the requirements of both military-grade standards and ASUS quality tests.4. Fingerprint sensor, backlit keyboard, TPM2.0 and a front camera are optional.5.All specifications are subject to change without notice. Please check with your supplier for exact offers. Products may not be available in all markets.B1500CEAE / B1500CEPEBuilt-in biometric security, with a fingerprint sensor that’s integrated into the power button.Rock Solid construction with alumni-alloy lid, internal still bracing and proactive foam to protect HDD.A dTPM chip securely stores authentication information used by software, such as password and importation transactions.OMNI-CONNECTIVITYMultiple connections ensuring a seamless interfaceThunderbolt™ 4.0 support Power Delivery,USB 2.0。

PhilipsLCD widescreen monitor51 cm (20.1") wideWSXGA200WS8FB Vista-ready widescreen forbusiness productivityDo more, see more on budget! With high resolution and a large, wide viewing area, thisultra-slim Philips 200WS8 boosts your business productivity - and is ready for immediateor future upgrade to Windows Vista.Designed for maximum productivity•Big, widescreen ideal for viewing two A4 pages side-by-side•Display more images and content without scrollingBest total cost of ownership solution•Empowered for Windows Vista•Complies with RoHS standards to care for the environment•The lowest power consumption in the industryOutstanding front of screen performance•WSXGA+, wide format 1680x1050 resolution for sharper display•5ms fast response time•DVI-D input and HDCP supportGreat convenience•Dual input accepts both analog VGA and digital DVI signals•Embedded power supply eliminates external power adaptors•Adjust display settings with hot key or on-screen controlsHighlightsWidescreenA big, widescreen display that improves productivity by displaying two A4 pages side-by-side.Large viewing areaViewing area is the visible portion of a monitor screen available for displaying data. Windows Vista readyPhilips Vista-ready monitors are empowered for vibrant, exciting display of this new, visually sophisticated and demanding Windows operating system, designed to enhance your entertainment experience, make you more productive and help you control your computing experience at home and in the office, making viewing, finding and organizing information for work or play quick, efficient and easy.Compliant with RoHS standards Philips designs and produces display products in compliance with strict Restriction of Hazardous Substances (RoHS) standards that restrict lead and other toxic substances that can harm the environment.Lowest power consumptionLower power consumption reduces the energyrequired to operate a device, saving its owneroperating costs and conserving power.WSXGA+, wide format 1680x1050Wide format, super extended graphics array isa display specification that is capable ofdisplaying 1680 x 1050 resolution orapproximately 1.7 million pixels.5ms on/off response timeOn-Off response time is the period requiredfor a liquid crystal cell to go from active (black)to inactive (white) and back to active (black)again. It is measured in milliseconds. Faster isbetter: Lower response time means fastertransitions and, therefore, results in fewervisible image artifacts in the display oftransition of texts and graphics. On-Offresponse time is a more important measure inthe display of business content like documents,graphs and photos.HDCP readyHigh-Bandwidth Digital Content Protection(HDCP) is a copyright protection system thatis incorporated into the DVI connector. Ithelps stop unauthorized duplication ofcopyrighted content. HDCP allows you to playprotected content media such as movies andconcerts. It checks the signal to prevent piracy,allowing only legal copies of content to display.Dual inputDual input provides connectors toaccommodate input of both analog VGA anddigital DVI signals.Embedded power supplyAn embedded power supply is a poweradaptor built into the body of a display devicethat replaces a bulky external power adaptor.User friendly hot key and OSDThe user friendly hot key and on-screen displaycontrols are dual systems for convenientlyfine-tuning display settings to meet a variety ofneeds. Press the hot key on your monitor'sframe for automatic picture, quick contrast andbrightness control or use the on-screen displayfeature to fine-tune your display settings.Issue date 2022-05-18 Version: 3.0.1012 NC: 8670 000 30111 EAN: 87 12581 30351 8© 2022 Koninklijke Philips N.V.All Rights reserved.Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips N.V. or their respective owners.SpecificationsPicture/Display•LCD panel type: 1680 x 1050 pixels, Anti-glare polarizer, RGB vertical stripe•Panel Size: 20.1"/ 51 cm•Effective viewing area: 433.4 x 270.9 mm •Pixel pitch: 0.258 x 0.258 mm •Brightness: 300 cd/m²•Contrast ratio (typical): 800:1•Display colors: 16.7 M•Viewing angle: 160º (H) / 160º (V), @ C/R > 10•Response time (typical): 5 ms•White Chromaticity, 6500K: x = 0.313 / y = 0.329•White Chromaticity, 9300K: x = 0.283 / y = 0.297•Maximum Resolution: 1680 x 1050 @ 60Hz •Optimum resolution: 1680 x 1050 @ 60Hz •Video Dot Rate: 205 MHz•Horizontal Scanning Frequency: 30 - 93 kHz •Vertical Scanning Frequency: 56 - 76 Hz •Aspect ratio: 16:10•sRGBConnectivity•Signal Input: VGA (Analog ), DVI-D•Sync Input: Composite Sync, Separate Sync, Sync on Green•Video input impedance: 75 ohm•Sync input impedance: 2.2k ohm•Video input signal levels: 0.7 Vpp Convenience•User convenience: On-screen Display •Monitor Controls: Auto, Brightness (Left), Contrast (Right), Menu, Power On/Off•OSD Languages: English, French, German, Italian, Simplified Chinese, Spanish•Other convenience: Kensington lock compatible •Plug & Play Compatibility: DDC/CI, sRGB, Windows 98/ME/2000/XP/Vista•Regulatory approvals: CE Mark, Energy Star, FCCClass B, SEMKO, TCO '03, TÜV/GS, TÜV Ergo, UL/cUL•Tilt: -5° to 25°•VESA Mount: 100 x 100 mmAccessories•Included accessories: AC Power Cord, VGA cable •User ManualDimensions•Box dimensions(W x H x D):525 x 174 x 452 mm•Box dimensions in inch (W x H x D):20.7 x 6.9 x 17.8 inch•Set dimensions(W x H x D):472.89 x 310.23 x 73 mm•Set dimensions in inch (W x H x D):18.6 x 12.2 x 2.9 inch•Set dimensions with stand (W x H x D):472.89 x 400.42 x 213.59 mm•Set dimensions with stand in inch (W x H x D): 18.6 x 15.8 x 8.4 inch•MTBF: 50,000 hrs•Relative humidity: 20% - 80%•Temperature range (operation): 5°C to 35°C •Temperature range (storage): -20°C to 60°C •Product weight (+stand): 5.3 kg•Product weight (+stand) (lb): 11.7 lb•Weight incl. Packaging: 6.1 kg•Weight incl. Packaging (lb): 13.4 lbPower•Complies with: Energy Star•Consumption (On mode): < 43 W (Typical)•Consumption(Off Mode): < 1 W•Power LED indicator: Operation - green, Stand by/ sleep - Amber•Power supply: Built-in, 100-240VAC, 50/60Hz。

Data SheetFujitsu Display B24-8 TE ProAdvanced display: 60.5 cm (23.8-inch) widescreenBest ergonomic and energy saving solutions for office applicationsThe FUJITSU Display B24-8 TE Pro is made for intensive office work. With visual and mechanical ergonomics this marble-grey display enables fatigue-free working for hours in front of the screen. The large 60.5 cm (23.8-inch) screen allows you to keep always track of all open applications. This high-quality display works unfailingly around the clock. Easy connectivity, manageability and usability help you increase your productivity.The display provides an excellent visual performance with In-Plane Switching (IPS) technology.The display had an optimized and relaxed position and provides an ergonomic stand featuring height adjust, swivel, tilt and 90° rotation.The DisplayView software enables you to configure your monitor for adjusting screen brightness, pivot function and much more.The display allows for flexible connectivity with DisplayPort, DVI, Analog and USB.The smart design with space saving front frame and smart details like discretely integrated speakers and cable guide allow for a clean desk.The environment-friendly LED technology provides unique, high efficient energy saving solutions like ECO operation mode and ECO standby.Technical detailsSpecial featuresIn-Plane Switching (IPS) technology, Eco button for Eco mode and 3-coloured Eco status LED, 5-in-1 Stand, Cableguide, Pivot, Always available USB (in operating and standby mode), DisplayView™ Software, 24/7 usage, Headsetconnector, Integrated speakersErgonomic standStand5-in-1 StandHeight adjust range150 mmPicture height over desk (min)40 mmRotation to portrait90°Tilt angle-5° / +35°Swivel angle345°Picture performancePanel and backlit In-Plane Switching (IPS) technology/LEDScreen Surface Treatment Anti-glare, 3H hard coatingContrast - typical1,000:1Contrast - advanced20,000,000:1Response time gray to gray typical 5 ms (in video mode)Viewing angle (h/v) - typical178°/178° CR10:1Color performance16.7 million colorsBrightness - typical250 cd/m2Size and resolutionAspect ratio16:9Diagonal Size60.5 cm (23.8-inch)Resolution (native)1,920 x 1,080 pixelResolution (interpolated)1,680 x 1,050 pixel, 1,440 x 900 pixel, 1,280 x 1,024 pixel, 1,280 x 720 pixel, 1,024 x 768 pixel, 800 x 600 pixel, 640 x480 pixelPicture size527 x 296 mmPixel Pitch0.2745 mmFrequenciesHorizontal30 - 82 kHzVertical56 - 76 HzConnectivityDisplayPort 1 x DisplayPortDVI 1 x DVI-D (HDCP)VGA/D-SUB 1 x D-SUBAudio signal output 3.5 mm stereo phone jack for head phoneAudio signal input 3.5 mm stereo phone jackAudio sound output 2 x 2 WUSB downstream2x USB 2.0USB upstream 1 x USBEase-of-use menuLanguages Arabic, Czech, Danish, Dutch, English, Finnish, French, German, Italian, Norwegian, Polish, Portuguese, Russian,Spanish, Swedish, Turkish, Japanese, Chinese simply, Chinese traditionalBrightness / Contrast Brightness, Contrast, Black level, Auto levelMode sRGB, Office, Photo, Video, Low Blue LightColor sRGB, 5000K, 6500K, 7500K, Native, Custom Color (R,G,B)Image adjust Clock, Phase, H-Position, V-Position, ExpansionAudio Mute, Volume, Input for HDMI and DP interfaceInformation Model name, Serial number, Resolution/mode, Signal inputSetup Input select, Language, DDC/CI, OSD-Timeout, Factory presetPower consumption (typical, w/o sound)Soft switch off0.14 WPower save mode0.17 WOperating with EPA settings11.95 WTotal Energy Consumption (ETEC)43.6 kWh/yearOperating maximum brightness22 WPower supply integratedPower notes Speakers off, USB not connectedETEC and EPA refer to ENERGY STAR® 8.0Electrical valuesRated voltage range100 V - 240 VRated frequency range50 Hz - 60 HzProtection class1ComplianceEurope EN 62368-1, CE certification according to EC Directive 2004/108/EEC, RoHS, WEEE, IT-Eco-DeclarationModel B24-8TGermany TÜV GSRussia EACUSA/Canada FCC Class B, cTUVusAustralia/New Zealand RCMSouth Korea KCSingapore S-MarkTaiwan BSMIChina CCCGlobal ENERGY STAR® 8.0, EPEAT® Bronze (dedicated regions), TÜV Low Blue Light Certified, TÜV Flicker Free Certified, Zerobright and dark pixel faults, Subpixel faults according to ISO9241-307 (Pixel fault class I), TCO Certified Compliance link https:///sites/certificatesDimensions / Weight / EnvironmentalDimension without stand (W x D x H)553 x 63.5 x 330.2 mm21.77 x 2.5 x 13.00 inchDimension with stand (W x D x H)553 x 229.4 x 347 mm21.77 x 9.03 x 13.65 inchWeight (packed)7.4 kg16.20 lbsWeight (unpacked) 5.6 kg12.35 lbsWeight (Monitor only) 3.5 kg7.74 lbsOperating ambient temperature 5 - 35 °C (41 - 95 °F)Operating relative humidity10 - 85 % (non condensing)MiscellaneousMiscellaneous VESA DDC/ CI, Flat Display Mounting Interface VESA MIS-D 100 C, Kensington lock preparedColor Marble greyPackage contentDisplay delivered accessories DisplayPort data cable 1.8 mDVI-D Data cable 1.8 mAudio cable 1.8 mUSB-cable 1.8 m (USB-A to USB-B)Power cable for wall socket (Euro-Schuko-Type CEE7) 1.8 mQuickstart flyerSafety notesDisplay delivered accessories notes Power cable with IEC-60320-C13, 3-pin connector on display sideData cables and USB cable detachable on displayUser manual and DisplayView Software is available via downloadPackaging dimension (mm)Weight (packed)7.4 kgWeight (packed) (lbs)16.20 lbsWarrantyWarranty period 3 years (depending on country)Spare Parts availability at least 7 years after shipment, for details see https:///5 yearsContactAddress: x-xx-x, street, city, state, ZIP code, country Phone: xx-xxxx-xxxx Fax : xx-xxxx-xxxxEmail:********************.com Website: /[country]2023-11-27 CE-ENdelivery subject to availability. Any liability that the data and illustrations are complete, actual or correct is excluded. Designations may be trademarks and/or copyrights of the respective manufacturer, the use of which by third parties for their own purposes may infringe the rights of such ownerMore informationAll rights reserved, including intellectual property rights. Changes to technical data reserved. Delivery subject to availability. Any liability that the data and illustrations are complete, actual or correct is excluded.Designations may be trademarks and/or copyrights of the respective manufacturer, the use of which by third parties for their own purposes may infringe the rights of such owner.For further information see /terms_of_use.html Copyright © Fujitsu Technology Solutions。

MEMSHIELD 4 INSTALLATION INSTRUCTIONS FOR 400A PANELBOARDS/ PAN ASSEMBLIES EM4PB840, EM4PB1440, EM4PB1840EM4PBP840, EM4PBP1440, EM4PBP1840Instruction Leaflet LT1222 (02/19)400A Incoming MCCB EM4PBK404Remove for accessIncoming Modules3 Pole & Neutral -Bottom Entry Form4 Type 6 Group MountedSecure all shields4 Pole -Bottom Entry Form 4 Type 6 Group MountedSecure all shields400A Incoming Direct Cable EM4PBK404L4 Pole -Bottom Entry Form 4 Type 6Secure all shields30NmRemove for accessFit MountPanelboard’s are supplied as Bottom Entry and Form 4 Type 6 Group Mounted without modification General Note: When fixing M5 thread formingscrews tightening torque is 3.8 NmFit shield Remove incoming mount. 400A Incoming Neutral EM4PBNK40NL1L2L330NmClick cover shield in to incoming cover apertureNL1L2L3Incoming mountFit neutralBottom EntryIMPORTANT NOTES1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician inaccordance with current electrical engineering Codes of Practice, Requirements for the Electrical Installations (IET Wiring Regulations BS7671), Construction (Design and Management) Regulations, HSG150 –Health and Safety in Construction, Statutory requirements and any Specific instruction issued by the Company.2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of the person responsible for its future operation and maintenance, and is at all times available for ready reference.3. The notes assume throughout that the product is disconnected from the supply. It is essential that this is done before any work is carried out.4. These Panelboards are only designed for use with EATON MCCBs. Failure to comply will result in invalid warranty and certification.31Nm31NmFitInterphase shieldsSupport fixingsOutgoing MCCB Adaptors and Neutral ModulesNZM1 4 Pole Form 4 Type 6Compartmentalised/Group Mounted EM4PBFAN14NZM1 3PN Form 4 Type 6 Group Mounted/ Form 4 Type 2 Compartmentalised. EM4PBGMN1N NZM1 3PN Form 4 Type 6 Compartmentalised EM4PBCKN1NImportant all Adaptors : Fit MCCB with the adjustment dial end towards the adaptor stabsGroup mounted when finger guard fittedNZM1 -EM4PBFAN1L1-3N, EM4PBFAN14EM4PBGMN1N, EM4PBCKN1NNZM1 SPN Form 4 Type 6 Compartmentalised/Group Mounted EM4PBFAN1L1-3NNZM2 -EM4PBFAN24, EM4PBGMN2N, EM4PBCKN2NGroup mounted when finger guard fittedNZM2 4 Pole Form 4 Type 6Compartmentalised/Group Mounted EM4PBFAN24NZM2 3PN Form 4 Type 6 Compartmentalised EM4PBCKN2N9Nm14NmAlign adaptor guides in key holesWith screwdriver rack adaptor in or outForm 4 Type 6 Group MountedGroup Mounted Cover BlankEM4PBGMBPFit NZM1 Adaptor Cover ShieldNZM2 3PN Form 4 Type 6 Group Mounted/ Form 4 Type 2 Compartmentalised. EM4PBGMN2N Secure inserted adaptor with x2 fixingsSupport fixingsSupport fixingsSupport fixingsM8 X 25Top Entry ConversionLift off front doors and rotate panelboard 180°Reposition x6 male hinges on enclosure. Ensure existing scratchwasher andM5 fixings are reused and tightenedNew positionExisting positionUtilising the same connectors, screws and washers, reconfigure fromBottom to Top EntryEnsure connectors are kept in their supplied sets and spring washers arealways fitted beneath the screwsL3L2Bottom Entry L1NRemove shields to gain access to connectors. Remembering to replace all shields after connector reconfigurationTop EntryN L1L2L3Build Sequence for Top Entry4L3N1M8 X 253L2M8 X 25L1Tightening torque for all connectors –15Nm2M8 X 25FitInterphase shieldsTop entry neutral shieldReposition HingesFit Incomer31Nm 31Nm 14-18 Way Cableway –Remove x1 cut-out feature in cableway to gain access tooutgoing chamberRotate dished cover180°and fix x4 screwsCableways, Extension/Corner/DIN Boxes and PlinthsCableway-EM4PB68SXB EM4PB1214SXB EM4PB1618SXBFits either sideExtension/DIN Box-EM4PB250EX EM4PB250EXDINFits either end Corner Box-EM4PB300CXFits either sideBox fixing, ensure scratch washers are fitted both sidesCableway -Provision to move earth bar into cableway, utilising earth strapPlinth –Fit plinth gland plate inside panelboard15Nm30NmNL1NL2L1NPlinthEM4PB100PL EM4PB100PLCX Remove x6 malehinges fromenclosure and drill 2.2mmØ holes as shown6mmØ5mmØRemove all swarfCompartmentalise Module EM4PBCKConversion to Form 4 Type 2/ Form 4 Type 6 CompartmentalisedWhen converting to Compartmentalised, cableways must be fitted either side of panelboardForm 4 Type 2 Compartmentalised Module EM4PBCKN122, EM4PBCKN142, EM4PBCKN242Fit compartment with 7 x M5 fixings (Example EM4PBCKN242)EM4PBCKN242EM4PBCKN142EM4PBCKN122EM4PBCKUWTrim shield and cover to suit For both Form 4 Type 2 and Type 6Fit cover with 6 x M5 fixingsFix with 4 x M5 fixingsFix with 4 x M5 fixingsFix with 2 x M5 fixingsFix with 4 x M5 fixingsFix with 4 x M5 fixingsFix with 5 x M5 fixings per coverForm 4 Type 6 Compartmentalised Outgoing Modules EM4PBCKN126, EM4PBCKN146, EM4PBCKN246Fit compartment with 7 x M5 fixings (ExampleEM4PBCKN246)Fit cover with 8 x M5 fixingsAdaptor Assembly –1.Interphase barriers to mccb2.Type 6 shield to carriage3.Extension palms to mccbPrepare AdaptorNZM2NZM1 4PNZM1 SPNEM4PBCKN246EM4PBCKN146EM4PBCKN126Form 4 Type 6 Compartmentalised Incoming Module EM4PB40CKINCRemove cut out -Bottom Fed Top FedAssemble incoming palms to device. Slide shield over connectors and interphase barriers, fix in place with 4 x M5.Fit device type 6 shield and finish with fitting incoming kit shield14Nm9Nm15Nm15Nm31Nm31NmLifting Eye Kit EM4PBLEUtilising existing M5 screws3.8NmPan Assemblies EM4PBP840, EM4PBP1440, EM4PBP18400EM4PBP1840Form 4 Type 2/6 Compartmentalised Blanking Way EM4PBCKN12BK, EM4PBCKN14BK EM4PBCKN24BKEmpty CompartmentFit blanking way with 2 x M6 fixingsDrawn as 8 way pan with 400A incoming kitLabel FittingEnsure x7 labels supplied with panelboard are fitted in the correct places as shown in this bottom entry example.For top entry, the labels are in the same position but rotated through 180°Panelboard LabelsSupply label fitted to incoming coverOutgoing Adaptor Labels2off labels supplied with outgoing adaptors to be fitted as shown 12213456721 & 3456Group MountedCompartmentalised12Maximum Thermal Ratings for Incoming and Outgoing DevicesThe ratings shown below cover top or bottom entry and all group mounted/compartmentalised configurations Maximum Incomer400A MCCB = 400A 400A Direct Cable = 400A Maximum Outgoer I RDF NZM1 Single Pole 125A = 125A 0.8NZM1 3-4 Pole 125A = 122A 0.82NZM1 3-4 Pole 160A = 160A 0.8NZM2 3-4 Pole 250A = 217A 0.8INSTALLATION DATE______________________CONTRACTOR___________________________FED FROM _______________________________INCOMING CABLE SIZE _____________________LH OUTGOING CIRCUITSRH OUTGOING CIRCUITS MAIN BUSBAR CIRCUITSLH EARTH CIRCUITSRH EARTH CIRCUITS8 WAY14 WAY18 WAY8 WAY 14 WAY18 WAY8 WAY14 WAY18 WAYWarning!Intellectual Property Rights!Eaton wishes to make it clear that it owns intellectual property rights in the product which it manufactures (whether or not listed in this leaflet) and that it will take legal action against any party found to be manufacturing, using, or selling any article which infringes the company’s intellectual property. All marks in this document identified with an R symbol or a TM symbol adjacent to the mark are trademarks of Eaton.© 2019 Eaton Electric Limited. All rights /recyclingThe use to which this product is put and its place of installation is outsideour control. Particular care should therefore be taken to follow the instructions given here and to ensure their continued availability in conjunction with the use of the product.No responsibility can be accepted by us if these instructions are disregarded.Further copies of these instructions and information concerning theinstallation and proper use of this product can be obtained by contacting the: Technical Services DepartmentEaton Electric Limited, Middleton, Manchester, M24 1GQ Tel: +44(0)8700 545 333email:**********************nc。

AOC-STG-b4SUser's GuideRevision 1.0bUser's Guide Revision 1.0bRelease Date: December 29, 2014Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document.Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.Copyright © 2014 by Super Micro Computer, Inc. All rights reserved.Printed in the United States of AmericaThe information in this User's Guide has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this user's guide, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this user's guide, please see our Website at .Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this user's guide at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.Any disputes arising between the manufacturer and the customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See /hazardouswaste/perchlorate”.WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.PrefacePrefaceAbout this User's GuideThis user's guide is written for system integrators, IT technicians and knowledgeable end users. It provides information for the installation and use of the AOC-STG-b4S add-on card.About this Add-on CardThe Supermicro AOC-STG-b4S is the most energy-efficient and cost-effective 4-port 10GbE adapter solution for data centers in today's market. The AOC-STG-b4S supports a wide range of popular networking features. These features include TCP Offload, PXE boot, Virtualization technology (VMDq and PC-SIG SR-IOV), and Energy Efficient Ethernet (IEEE 802.3az). The Supermicro AOC-STG-b4S add-on card offers the highest performance with the lowest power consumption currently available on the market. This add-on card is intended to be used with Supermicro's servers or motherboards as an integrated solution package. For more information regarding product support or updates, please refer to our website at http://www./products/nfo/networking.cfm#adapter.An Important Note to the UserAll images and layouts shown in this user's guide are based upon the latest PCB Revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this user's guide.Returning Merchandise for ServiceA receipt or copy of your invoice marked with the date of purchase is required beforeany warranty service will be rendered. You can obtain service by calling your ven-dor for a Returned Merchandise Authorization (RMA) number. When returning the motherboard to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and the shipping package is mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete. For faster service, You can also requesta RMA authorization online /RmaForm/.This warranty only covers normal consumer use and does not cover damages in-curred in shipping or from failure due to the alternation, misuse, abuse or improper maintenance of products.During the warranty period, contact your distributor first for any product problems.Conventions Used in the User's GuidePay special attention to the following symbols for proper system installation and for safety instructions to prevent damage to the system or injury to yourself:Warning: Important information given to ensure proper system installation or to prevent damage to the components or injury to yourself.Note:Additional information given for proper system setup.Naming ConventionCharacter Representation Options1st Product Family AOC: Add On Card2nd Form Factor U: UIO, S: Standard, P: Proprietary, C: MicroLP 3rdProduct Type/SpeedG: GbE (1Gb/s), TG: 10GbE (10Gb/s) , IBF: IB FDR (56Gb/s) IBQ: IB QDR (40Gb/s), INF: InfiniBand DDR (20Gb/s)4th Chipset Model (Optional)N: Niantec (82599ES), P: Powerville (i350)5th Chipset Manufacturer i: Intel, m: Mellanox, b: Broadcom 6th Number of Ports1: 1 port, 2: 2 ports, 4: 4 ports 7thConnector Type (Optional)S: SFP+, T: 10GBase-TNaming ConventionPreface Contacting SupermicroHeadquartersAddress:Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel:+1 (408) 503-8000Fax:+1 (408) 503-8008Email:************************(GeneralInformation)**********************(TechnicalSupport)Website:EuropeAddress:Super Micro Computer B.V.Het Sterrenbeeld 28, 5215 ML's-Hertogenbosch, The NetherlandsTel:+31 (0) 73-6400390Fax:+31 (0) 73-6416525Email:*******************(GeneralInformation)*********************(TechnicalSupport)*****************(CustomerSupport)Website:www.supermicro.nlAsia-PacificAddress:Super Micro Computer, Inc.3F, No. 150, Jian 1st Rd.Zhonghe Dist., New Taipei City 235Taiwan (R.O.C)Tel:+886-(2) 8226-3990Fax:+886-(2) 8226-3992Email:**********************.twWebsite:Table of ContentsPrefaceChapter 1 Overview1-1 Overview .........................................................................................................1-1 1-2 Product Highlights ...........................................................................................1-1 1-3 Technical Specifications ..................................................................................1-2 General ............................................................................................................1-2 Ethernet Features ...........................................................................................1-2 Network Features ............................................................................................1-2 Remote Boot Options ......................................................................................1-3 Virtualization Features.....................................................................................1-3 Cable Support .................................................................................................1-3 OS Support .....................................................................................................1-3 Physical Dimensions .......................................................................................1-4 Optional Accessories .....................................................................................1-4 Operating Conditions .....................................................................................1-4 1-4 Compliance/Operating Environment ...............................................................1-5 1-5 SMC Platform Support ....................................................................................1-5 Chapter 2 Hardware Components2-1 Add-On Card Image and Layout .....................................................................2-1 2-2 Major Components ..........................................................................................2-1 2-3 Connectors: LAN Ports and LAN LED Indicators ...........................................2-2 LAN Ports ...................................................................................................2-2LAN Port LED Indicators ............................................................................2-2 Chapter 3 Installation3-1 Static-Sensitive Devices..................................................................................3-1 Precautions .....................................................................................................3-1 Unpacking .......................................................................................................3-1 3-2 Before Installation ...........................................................................................3-1 3-3 Installing the Add-on Card ..............................................................................3-2 3-4 Installing the Windows Operating System ......................................................3-4 3-5 Installing Other Operating Systems ................................................................3-4Chapter 1: OverviewChapter 1Overview1-1 OverviewCongratulations on purchasing your add-on card from an acknowledged leader in the industry. Supermicro products are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. For product support and updates, please refer to our website at / products/nfo/networking.cfm#adapter.1-2 Product HighlightsThe product highlights of this add-on card include the following:• Quad SFP+ Ports• Low-Profile Standard Form Factor• PCI Express 3.0 (8GT/s)• TCP Offload Engine (TOE)• VMDq and PC-SIG SR-IOV for Virtualized Environments• Jumbo Frame Support• IEEE 802.3az Energy Efficient Ethernet (EEE)• Low Power Consumption (about 14W)• iSCSI Remote Boot Support• PXE Boot Support• RoHS Compliance 6.61-3 Technical SpecificationsGeneral• Broadcom BMC57840S controller• Compact size low-profile standard form factor• PCI-E 3.0 x8 (8GT/s) interface• Quad SFP+ connectorsEthernet Features• Energy Efficient Ethernet IEEE 802.az supported• Traffic Steering for MAC address and VLAN Tag• Up to 32 queues/port supported for RSS (Receive Side Scaling)• Congestion Notification 802.1au• Large Send Offload (LSO) and Large Receive Offload (LRO)• Link Aggregation 802.3adNetwork Features• Jumbo Frames up to 9600 Bytes• Clause 73 Auto-negotiation• IEEE 801.2q VLAN• External PHY support• TCP Offload Engine (TOE) reduces host CPU utilization while preserving the rich and flexible nature of soft OS stack implementation• iSCSI Acceleration• IPv6 AccelerationChapter 1: Overview • Support port aggregation, failover, load balancingRemote Boot Options• Preboot eXecution Environment (PXE) support• iSCSI remote bootVirtualization Features• Up to 128 per port for VMDq• SR-IOV with up to 64 Virtual Functions (VFs) for Guest Operating Systems (GOS) per port• Supports NetQueue and VMQueue• Supports Data Center Bridging which provides secure data delivery, lower latency, and standards-based bandwidth sharing of data center physical links • Supports up to 68 Rx/Tx Descriptor Queues for Virtualization per port • Supports up to 136 MAC Addresses per port• Supports EEE 802.1Qau Congestion NotificationCable Support• SFP+ direct attached twin axial cables, up to 5 meters• LC-LC fiber-optic cables (with required optional transceivers)OS SupportThe AOC-STG-b4S add-on card supports the following operating systems (OS):• Windows® 2008 Server R2 (with HyperV), Server 2012 (with HyperV)• Linux: RedHat EL 5, 6, and 7• SuSE SLES 10, 11, and 12• VMware ESX 5.0 (vSphere 5.0), 5.1 (vSphere 5.1), and 6.0 (vSphere 6.0)• Solaris 11Physical Dimensions• Card PCB dimensions: 13.72cm (5.4in) x 6.90cm (2.73in) (L x H)• Height of end brackets: Standard 12cm (4.725in), low-profile 7.94cm (3.13in)Optional Accessories• AOC-E10GSFPSR: SFP+ transceiver module for short range fiber cables (up to 300m)• AOC-E10GSFPLR: SFP+ transceiver module for long range fiber cables (up to 3000m)• AOC-TSR-FS: SFP+ transceiver module for short range fiber cables (up to 300m) • AOC-GBIC-FSR2: SFP+ transceiver module for short range fiber cables (up to 300m), single speed (10Gb)• CBL-0347L: 39.37" (100cm) 10GbE SFP+ to SFP+, Twinax copper cable • CBL-0456L: 78.74" (200cm) 10GbE SFP+ to SFP+, Twinax copper cable • CBL-0348L: 118.11" (300cm) 10GbE SFP+ to SFP+, Twinax copper cable • CBL-0349L: 196.85" (500cm) 10GbE SFP+ to SFP+, Twinax copper cableOperating Conditions• Operating temperature: 0°C to 55°C (32°F to 131°F)• Storage temperature: -40°C to 70°C (-40°F to 158°F)Note: This product is intended to be used with Supermicro server systemsor motherboards as an integrated solution package.Chapter 1: Overview1-4 Compliance/Operating EnvironmentThe AOC-STG-b4S add-on card is compliant with the following environmental regulations:• RoHS Compliant 6/6, Pb Free1-5 SMC Platform SupportThe following platforms are supported by the AOC-STG-b4S add-on card:• Supermicro motherboards with minimum PCI-E x8 slot with enough clearance • Supermicro Server systems with low-profile or full-height PCI-E x8 expansionslot with enough clearance•Supermicro chassis as specified in the Matrix below:installed* = There will be a tooling change for the low-profile slot.**= Top slot is the SFP+ port farthest away from the PCI-E Goldfinger on the PCB.AOC-STGN-b4S Fitment MatrixChassisFH Slot LP Slot NotesF627R3-RTB+/72B+ Top** slot is blocked by a rivet, other 3 can be used F617R2-RT+/R72+* Top** slot is blocked by a rivet, other 3 can be used F617R3/2-FT+ Top** slot is blocked by a rivet, other 3 can be usedF627R2-F73 Cannot be installedF627G2-FT+/F73+x 118G(Q) xWill work with SFP+ cable in all 4 slots, but rivet keeps transciever from working in top** slot213-LPB x 213-WIO x x 216-LPB x 417-LPB x 819TQ-WIO x x 825-LPB x 825-WIO x x825M-LPB x 826-LPB x827H Cannot be installed 827HQCannot be installed 847-LPB x 847-WIO x x 938HCannot be installedx = can be installed* = There will be a tooling change for the low-profile slot.** = Top slot is the SFP+ port farthest from the PCI-Express Goldfinger on the PCB.NotesChapter 2: Hardware ComponentsChapter 2Hardware Components2-1 Add-On Card Image and LayoutThe AOC-STG-b4S ImageThe AOC-STG-b4S Layout242-2 Major ComponentsThe following major components are installed on the AOC-STG-b4S:1. Broadcom BMC57840S Controller 2. SFP+ Connector 13. SFP+ Connector 24. SFP+ Connector 35. SFP+ Connector 4135LAN Port LED IndicatorsFour LAN ports (SFP+1-SFP+4) are located on the add-on card. Each LAN port has two LEDs. The LED on the left indicates link speeds, and the other LED on the right indicate the status of activity of the connector. See the table below for more information. LAN PortsFour network LAN ports (SFP+1-SFP+4) are located on the add-on card. These LAN ports support connection speeds of 10Gbps and 1Gbps. Plug the Direct Attached Copper (DAC) cables into the SFP+ ports for network connections.Note 1: To make sure that LAN ports function properly, be sure to use the following cables specified by the manufacturer:• Direct-attached twin-axial copper cables, or• Short Range or Long Range fiber optic cables used in conjunction withoptional optical transceiver.Note 2: For detailed information on the cables and transceivers recom-mended by the manufacturer, please refer to "Optional Accessories" onPage 1-4 or SMC product information posted online.2-3Connectors: LAN Ports and LAN LED IndicatorsSPDIF+The AOC-STG-b4S Card1234LAN Ports 1. SFP+ Port 12. SFP+ Port 23. SFP+ Port 34. SFP+ Port 4LAN LED Indicators A. Link LED B. Activity LEDSFP+Chapter 3: InstallationChapter 3Installation3-1 Static-Sensitive DevicesElectrostatic Discharge (ESD) can damage electronic com p onents. To avoid dam-aging your add-on card, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.Precautions• Use a grounded wrist strap designed to prevent static discharge.• Touch a grounded metal object before removing the add-on card from the antistatic bag.• Handle the add-on card by its edges only; do not touch its components, or peripheral chips.• Put the add-on card back into the antistatic bags when not in use.• For grounding purposes, make sure that your system chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the add-on card.UnpackingThe add-on card is shipped in antistatic packaging to avoid static damage. When unpacking your component or your system, make sure that the person handling it is static protected.Note: To avoid damaging your components and to ensure proper installa-tion, be sure to always connect the power cord last, and always remove itbefore adding, removing or changing any hardware components.3-2 Before InstallationTo install the add-on card properly, be sure to follow the instructions below.1. Power down the system.2. Remove the power cord from the wall socket.3. Use industry-standard anti-static equipment (such as gloves or wrist strap)and follow the instructions listed on Page 3-1 to avoid damage caused byESD.4. Familiarize yourself with the server, motherboard, and/or chassis documenta-tion.5. Confirm that your operating system includes the latest updates and hotfixes.3-3 Installing the Add-on CardFollow the steps below to install the add-on card into your system.1. Remove the server cover and, if necessary, set aside any screws for lateruse.2. Remove the add-on card slot cover. If the case requires a screw, place thescrew aside for later use.3. Position the add-on card in the slot directly over the connector, and gentlypush down on both sides of the card until it slides into the PCI connector.4. Secure the add-on card to the chassis. If required, use the screw that youpreviously removed.5. Attach any necessary external cables to the add-on card.6. Replace the chassis cover.7. Plug the power cord into the wall socket, and power up the system.8. Replace the chassis cover.Chapter 3: InstallationNote: This add-on card is designed to support the standard low-profile PCI-Express form factor; however, it may not fit in your chassis due to the physical dimensions of the card. See the drawing below for il-lustration.Note: The area enclosed by the dotted line indicates the dimensionsof the standard low-profile PCI-Express form factor. The areas that are enclosed in white rectangles might interfere with the components on your motherboard and prevent the card from being integrated into your system.Note : If the FOUND NEW HARDWARE WIZARD screen displays on your system, click CANCEL.3. Click on INSTALL DRIVERS AND SOFTWARE.4. Follow the prompts to complete the installation.3-5 Installing Other Operating SystemsFor detailed instructions on how to install the driver to an operating system other than the Windows OS, please refer to the Driver CD that came with this add-on card or refer to the Broadcom\Manuals section posted in Supermicro's ftp site.3-4 Installing the Windows Operating SystemFollow the steps below to install the drivers needed for your Windows OS support. The controller comes with a driver on the CD-ROM CDR-NIC.1. Run the CDR-NIC. (If you do not have a product CD-ROM, download driversfrom the Supermicro Support Website and then transfer them to your system.)2. When the SUPERMICRO window appears, click on the computer icon next tothe product model.(Disclaimer Continued)The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com-munication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous ap-plications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.。

Manuals+— User Manuals Simplified.GIGABYTE BRIXs Ultra Compact PC Kit User Guide Home » Gigabyte » GIGABYTE BRIXs Ultra Compact PC Kit User GuideContents1 GIGABYTE BRIXs Ultra Compact PCKit2 Product Information3 Product Usage Instructions4 Safety and Regulatory Information5 Package Contents6 Getting Familiar with Your Unit7 How to Install the M.2 2280 SSD8 Memory Installation9 Wireless Module10 Support 2.5” HDD/M.2 Upgrade Kit11 Documents / Resources11.1 ReferencesGIGABYTE BRIXs Ultra Compact PC KitAt the end of its serviceable life, this product should not be treated as household or general waste. It This device complies with part 15 of the FCC Rules.Memory InstallationWireless ModuleVESA BracketNOTE! The illustrations of the VESA bracket installation shown are for reference only. Please follow the installation steps of actual purchased bracket.: This system does not support the installation of both 2.5″ HDD and the M.2 module here cannot beInstall the upgrade kit drive on the bottom panel and secure with four screws provided, then connect the cable Connect the other end of the cable to the SATA connector on the motherboardReinstall the bottom cover with upgrade kit to system.Note 1 “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds thereference percentage value of presence condition.Note 1 “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.Note 2 “○” indicates that the percentage content of the restricted substance doesNote 3 The “ ” indicates that the restricted substance corresponds to the exemption.Documents / ResourcesGIGABYTE BRIXs Ultra Compact PC Kit [pdf] User GuideBRIXs Ultra Compact PC Kit, BRIXs, Ultra Compact PC Kit, Compact PC Kit, PC KitGIGABYTE BRIXs Ultra Compact PC Kit [pdf] User GuideBRIXs Ultra Compact PC Kit, BRIXs, Ultra Compact PC Kit, Compact PC Kit, PC Kit ReferencesTelepathy - Powering Successful BrandsManuals+,。

N32L40xx8/xB数据手册N32L40x系列采用32-bit ARM Cortex-M4F内核，最高工作主频64MHz，支持浮点运算和DSP指令，集成高达128KB嵌入式加密Flash，24KB SRAM，集成丰富的高性能模拟器件，内置1个12bit 4.5Msps ADC，2个独立轨到轨运算放大器，2个高速比较器，1个12bit 1Msps DAC，集成多达320段的Segment LCD驱动，集成多路U(S)ART、I2C、SPI、USB、CAN等数字通信接口，内置密码算法硬件加速引擎。

关键特性●内核CPU―32位ARM Cortex-M4内核+FPU，单周期硬件乘除法指令，支持DSP指令和MPU―内置2KB指令Cache缓存，支持Flash加速单元执行程序0等待―最高主频64MHz，80DMIPS●加密存储器―高达128KByte片内Flash，支持加密存储、多用户分区管理及数据保护、硬件ECC检查，10万次擦写次数，10年数据保持―24KByte SRAM，包括16Kbyte SRAM1（在STOP2模式下可配置为保持）和8Kbyte SRAM2（在STANDBY和STOP2模式下可配置为保持），支持硬件奇偶校验●低功耗管理―STANDBY模式：1.5uA，所有备份寄存器保持，IO保持，可选RTC Run，8KByte SRAM2保持，快速唤醒―STOP2模式：3uA、RTC Run、8KByte SRAM2保持、CPU寄存器保持、IO保持、快速唤醒―RUN模式：60uA/MHz@64MHz―LPRUN模式：PLL关闭，MSI作为系统主时钟，MR关闭，LPR开启，USB/CAN/SAC电源关闭，其他外设可选●Segment LCD显示驱动，最高支持176段（4x44）或320段（8x40）●高性能模拟接口―1个12bit 4.5Msps ADC，多精度可配置，6位模式下采样率高达8Msps，最多16个外部单端输入通道，支持差分模式―2个轨到轨运算放大器，内置最大32倍可编程增益放大器―2个高速模拟比较器，内置64级可调比较基准，COMP1支持在STOP2模式下工作―1个12bit DAC，采样率1Msps―内部2.048V独立参考电压参考源―内部集成低压检测单元●时钟―HSE：4MHz~32MHz外部高速晶体―LSE：32.768KHz外部低速晶体―HSI：内部高速RC16MHz―MSI：内部多速RC100K ~ 4MHz―LSI：内部低速RC 40KHz―内置高速PLL―MCO：支持1路时钟输出，可配置为低速或高速时钟输出●复位―支持上电/欠压/外部引脚复位―支持看门狗复位●最大支持64个GPIOs●通信接口―5个U(S)ART接口，其中3个USART接口（支持ISO7816，IrDA，LIN），2个UART接口―1个LPUART，支持STOP2模式唤醒MCU―2个SPI接口，速度高达16Mbps，支持I2S通信―2个I2C接口，速率高达1MHz，主从模式可配，从机模式下支持双地址响应―1个USB 2.0全速设备接口―1个CAN 2.0A/B总线接口●1个DMA控制器，支持8通道，通道源地址及目的地址任意可配●1个RTC实时时钟，支持闰年万年历，闹钟事件，周期性唤醒，支持内外部时钟校准●定时计数器―2个16bit高级定时计数器，支持输入捕获，互补输出，正交编码输入，最高控制精度9.25ns；每个定时器有4个独立的通道，其中3个通道支持6路互补PWM输出―5个16bit通用定时计数器，每个定时器有4个独立通道，支持输入捕获/输出比较/PWM输出―2个16bit基础定时计数器―1个16bit低功耗定时计数器，支持双脉冲计数功能，可在STOP2模式下工作―1个24bit SysTick―1个7bit窗口看门狗(WWDG)―1个12bit独立看门狗(IWDG)●编程方式―支持SWD/JTAG在线调试接口―支持UART和USB Bootloader●安全特性―内置密码算法硬件加速引擎―支持AES、DES、TDES、SHA1/224/256、SM1、SM3、SM4和SM7算法―闪存存储加密、多用户分区管理单元(MMU)―TRNG真随机数发生器―CRC16/32运算―支持写保护（WRP），多种读保护（RDP）等级（L0/L1/L2）―支持安全启动，程序加密下载，安全更新―支持外部时钟失效检测，入侵检测●96位UID和128位UCID●工作条件―工作电压范围：1.8V~3.6V―工作温度范围：-40℃～105℃―ESD：±4KV（HBM模型），±1KV（CDM模型）●封装―QFN32(4mm×4mm)―QFN48(6mm×6mm)―LQFP48(7mm×7mm)―QFN64(8mm×8mm)―LQFP64(10mm×10mm)―LQFP80(12mm×12mm)●订购型号目录1 产品简介 (11)命名规则 (12)器件一览 (13)2 功能简介 (14)处理器内核 (14)存储器 (14)嵌入式闪存存储器(FLASH) (14)嵌入式SRAM (15)嵌套的向量式中断控制器(NVIC) (15)外部中断/事件控制器(EXTI) (15)时钟系统 (15)启动模式 (16)供电方案 (16)复位 (17)可编程电压监测器 (17)电压调压器 (17)低功耗模式 (17)直接存储器存取(DMA) (18)实时时钟(RTC) (18)定时器和看门狗 (18)低功耗定时器（LPTIM） (18)基本定时器（TIM6和TIM7） (19)通用定时器(TIMx) (19)高级控制定时器(TIM1和TIM8) (20)系统时基定时器(Systick) (20)看门狗定时器(WDG) (20)I2C总线接口 (21)通用同步/异步收发器(USART) (22)低功耗通用异步接收器(LPUART) (24)串行外设接口(SPI) (24)串行音频接口(I2S) (25)控制器局域网络(CAN) (26)通用串行总线（USB） (26)通用输入输出接口(GPIO) (27)段式液晶显示驱动（LCD） (28)模拟/数字转换器(ADC) (28)运算放大器（OPAMP） (29)模拟比较器(COMP) (29)数字/模拟转换（DAC） (30)温度传感器(TS) (30)循环冗余校验计算单元(CRC) (30)密码算法硬件加速引擎(SAC) (31)唯一设备序列号(UID) (31)串行单线JTAG调试口(SWJ-DP) (31)3 引脚定义和描述 (32)封装示意图 (32)QFN32 (32)QFN48 (33)LQFP48 (34)QFN64 (35)LQFP64 (36)LQFP80 (37)引脚定义 (38)4 电气特性 (45)测试条件 (45)最小和最大数值 (45)典型数值 (45)典型曲线 (45)负载电容 (45)引脚输入电压 (45)供电方案 (46)电流消耗测量 (47)绝对最大额定值 (47)工作条件 (48)通用工作条件 (48)上电和掉电时的工作条件 (48)内嵌复位和电源控制模块特性 (48)内置参考电压 (49)供电电流特性 (49)外部时钟源特性 (51)内部时钟源特性 (54)从低功耗模式唤醒的时间 (56)PLL特性 (56)FLASH存储器特性 (57)绝对最大值(电气敏感性) (58)I/O端口特性 (58)NRST引脚特性 (61)TIM定时器和看门狗特性 (62)I2C接口特性 (64)SPI/I2S接口特性 (65)USB接口特性 (69)控制器局域网络(CAN)接口特性 (70)12位模数转换器(ADC)电气参数 (70)内部参考源（VREFBUFF）电气参数 (74)12位DAC电气参数 (74)运算放大器（OPAMP）电气参数 (75)比较器2(COMP2)电气参数 (76)比较器1(COMP1)电气参数 (77)液晶显示驱动器（Segment LCD）特性 (77)温度传感器(TS)特性 (78)5 封装尺寸 (79)QFN32 (79)QFN48 (80)LQFP48 (81)QFN64 (82)LQFP64 (83)LQFP80 (84)丝印说明 (85)6 版本历史 (86)7 声明 (89)表目录表1-1N32L40X系列资源配置 (13)表2-1定时器功能比较 (18)表3-1引脚定义 (38)表4-1电压特性 (47)表4-2电流特性 (47)表4-3温度特性 (47)表4-4通用工作条件 (48)表4-5上电和掉电时的工作条件 (48)表4-6内嵌复位和电源控制模块特性 (48)表4-7内置参考电压 (49)表4-8运行模式下的典型电流消耗，数据处理代码从内部闪存中运行 (49)表4-9睡眠模式下的典型电流消耗 (50)表4-10运行模式下的典型电流消耗，数据处理代码从内部闪存中运行 (50)表4-11睡眠模式下的典型电流消耗 (50)表4-12停机和待机模式下的典型电流消耗 (51)表4-13高速外部用户时钟特性（B YPASS模式） (51)表4-14低速外部用户时钟特性（B YPASS模式） (52)表4-15HSE4~32MH Z振荡器特性(1)(2) (53)表4-16LSE振荡器特性(F LSE=32.768K H Z)(1)(2)(4)(5) (54)表4-17MSI振荡器特性(1) (55)表4-18HSI振荡器特性(1)(2) (55)表4-19LSI振荡器特性(1) (56)表4-20低功耗模式的唤醒时间 (56)表4-21PLL特性 (56)表4-22闪存存储器特性 (57)表4-23闪存存储器寿命和数据保存期限 (58)表4-24ESD绝对最大值 (58)表4-25电气敏感性 (58)表4-26I/O静态特性 (58)表4-27IO输出驱动能力特性 (60)表4-28输出电压特性 (60)表4-29输入输出交流特性(1) (60)表4-30NRST引脚特性 (61)表4-31TIM1/8特性 (62)表4-32TIM2/3/4/5/6/7/9特性 (63)表4-33LPTIMER特性 (63)表4-34IWDG最大和最小计数复位时间（LSI=40K H Z） (63)表4-35WWDG最大和最小计数复位时间（APB1PCLK1=16MH Z） (63)表4-36I2C接口特性 (64)表4-37SPI特性(1) (65)表4-38I2S特性(1) (67)表4-39USB启动时间 (69)表4-40USB直流特性 (70)表4-41全速USB电气特性 (70)表4-42ADC特性 (70)表4-43ADC采样时间(1) (71)表4-44ADC精度–局限的测试条件(1)(2) (72)表4-45V REFBUFF特性 (74)表4-46DAC特性(1) (74)表4-47OPAMP特性 (75)表4-48COMP2特性 (76)表4-49COMP1特性 (77)表4-50COMP1低功耗模式特性 (77)表4-51LCD控制器特性 (77)表4-52温度传感器特性 (78)图目录图1-1N32L40X系列框图 (11)图1-2N32L40X系列订货代码信息图示 (12)图2-1存储器映射图 (14)图2-2时钟树 (16)图3-1N32L403系列QFN32引脚分布 (32)图3-2N32L406系列QFN48引脚分布 (33)图3-3N32L406系列LQFP48引脚分布 (34)图3-4N32L406系列QFN64引脚分布 (35)图3-5N32L406系列LQFP64引脚分布 (36)图3-6N32L406系列LQFP80引脚分布 (37)图4-1引脚的负载条件 (45)图4-2引脚输入电压 (46)图4-3供电方案 (46)图4-4电流消耗测量方案 (47)图4-5外部高速时钟源的交流时序图 (52)图4-6外部低速时钟源的交流时序图 (53)图4-7使用8MH Z晶体的典型应用 (53)图4-8使用32.768KH Z晶体的典型应用 (54)图4-9输入输出交流特性定义 (61)图4-10建议的NRST引脚保护 (62)图4-11I2C总线交流波形和测量电路(1) (65)图4-12SPI时序图–从模式和CLKPHA=0 (66)图4-13SPI时序图–从模式和CLKPHA=1(1) (67)图4-14SPI时序图–主模式(1) (67)图4-15I2S从模式时序图(飞利浦协议)(1) (69)图4-16I2S主模式时序图(飞利浦协议)(1) (69)图4-17USB时序：定义数据信号的上升和下降时间 (70)图4-18ADC精度特性 (73)图4-19使用ADC典型的连接图 (73)图4-20供电电源和参考电源去藕线路(V REF+与V DDA相连) (74)图5-1QFN32封装尺寸 (79)图5-2QFN48封装尺寸 (80)图5-3LQFP48封装尺寸 (81)图5-4QFN64封装尺寸 (82)图5-6LQFP80封装尺寸 (84)图5-7丝印说明 (85)1产品简介N32L40x系列微控制器产品采用高性能32位ARM Cortex™-M4F内核，集成浮点运算单元（FPU）和数字信号处理（DSP），支持并行计算指令。