漫步者A1说明书
- 格式:docx
- 大小:37.28 KB
- 文档页数:2
1. “MUTE”----静音放音状态时,按一下静音键将使音量快速关断,再按静音键将快速恢复原有音量。
2. “ ”----开机/待机 按“ ”键系统切换开机/待机,待机状态时,系统内部供电并未断开,显示窗 显示“- -”若长时间不使用,需关闭功放后面的电源开关。
3.“VOLUME+/-”----音量加减 控制主音量大小,音量值可在0~50之间调整。
4.“SW+/-”----低音音量调节 调节低音音量时,“BASS “指示灯亮。
5.“TRE+/-”键----高音音量调节 调节高音音量时,“TREB”指示灯亮。
6.“PC,AUX”----音频输入选择 按“PC”,系统播放PC音频信号,“PC”指示灯亮; 按“AUX”键,系统播放AUX音频信号,“AUX”指示灯亮。
1、将电源线接入市电,打开电源开关,系统进入放音状态,工作指示光圈和PC输入指示灯亮。
2、转动音量旋钮可调节主音量(0~50)。
3、放音状态时按攻放或遥控器上的“ ”键,系统即处于待机状态,工作指示光圈和输入指 示灯熄灭,显示窗显示“- -”,再按“ ”键开机。
E.I.D.C.功能说明放音只有一边音箱有声怎么办?首先请检查音箱之间的连线是否接好。
其次可以尝试连接其它音源设备,如音箱能正常发声,请检查您之前的音源。
如音箱仍不正常,请联系售后客服。
音箱都无声,怎么办?1、请检查电源插头是否插好,电源开关是否打开。
2、请检查音源和连接线是否正常。
3、请检查音源信号输出是否正常。
4、请检查音箱或音源的音量是否已被调至最小。
5、请断开音箱电源后重新开机。
音箱的噪声问题?漫步者音箱具有低噪声特点,有些音源的本底噪声会高出音箱的数倍。
所以检查时应拔掉音频线,然后开大音量,1米之外应基本听不到喇叭发出的声音。
遥控器不起作用版面设计:版本号及料号: V1.6名 称: C2X中文说明书材 质:尺 寸: 127X127mm 校 对:批 准:东莞市漫步者科技有限公司80克书纸说明书C2X/中文/含标示卡/V1.6*请阅读这些说明。
漫步者音箱说明书篇一:漫步者S5.1漫步者S5.1音箱使用说明书1、后面板1线路输入前左后左中置后中FL SL CE SCFR SR SW N前右后右低音闲置2、后面板2线路输出前右中置前左FR+ CE+ FL+FR_ CE_ FL_SR+ SC+ SL+SR_ SC_ SL_后右后中后左注:+为红色-为白色友情提醒:不要用自带的场景模式,用自选的,如下低音炮:4 前置低音:4 中音:4 高音:-1用遥控器调整吧。
参数:功率放大器输出功率:低音箱:rms 90w中置、前置,环绕:25w×5功率放大器总谐波失真:thd+n[0.5%功率放大器频响范围:卫星箱通道:20hz~20khz低音通道:20hz~200hz输入接口:莲花线路输入线路输入阻抗:50k欧姆低音单元:8寸铝音圈防磁纸盆单元,阻抗4欧姆卫星箱:4寸复合盆低音+1寸球顶高音扬声器,全防磁,阻抗8欧姆输入电源:ac~220v,50hz,600w低音箱箱体尺寸:270×496×496mm前置及后置卫星音箱箱体尺寸:150×230×161mm 中置音箱箱体尺寸:290×140h)×140mm包装箱:低音箱包装尺寸:600×350×600mm低音箱包装总重量:约24kg卫星箱包装尺寸:645×230×565mm卫星箱包装总重量:约18kg调节功能:调节方式:控制面板按键控制,遥控器遥控调节项目:总音量,范围0—60,精度1db中置、前置、环绕音量微调,范围-7—+7,精度1db前置通道高音,中音、低音音调调节,范围-7—+7,精度2db显示方式:荧光屏篇二:漫步者S2.1MKII音箱产品S2.1MKII充满阳刚之气,RMS功率高达300W!由内而外均是超强配置,比普通“大功率家庭影院”更令人疯狂。
卫星箱采用真正钢琴漆工艺,光洁如镜。
配备专门研发的25mm球顶丝膜高音单元和3.5英寸中音扬声器,以及复杂而精确的分频器,音质表现堪比高档立体声音箱。
www.edifi
北京爱德发科技有限公司
地址: 北京市海淀区北四环西路68号
中国制造
Beijing Edifier Technology Co., Ltd.
Made in China
微信扫一扫,更多信息
* 安全警告标识在产品或电源适配器的外壳或底部:
此符号提醒用户产品的外壳内部存在未绝缘的危险电压, 会引起触电, 此符号提醒用户不要拆卸产品的外壳, 换的部件, 此符号表示本产品只适用于室内环境。
此符号表示本产品是CLASS II或双重绝缘的电子设备, 接地保护。
* 本产品可以在海拔5000米及以下地区安全使用, 条件下安全使用。
* 带有接地插头的产品,* 对于可分离的电源线, 能保持方便的使用; 装置,应能保持方便的使用。
* 带有全极开关的产品, 便的使用。
警告!
* 电池更换不当会有爆炸危险, 来更换。
* 针对可拆卸电池的产品, 卸电池的产品,* 电池禁止拆解、 材料、液体、* 如果电池出现鼓胀、 勿继续使用。
* 如果电池使用不当, 人身伤害; 律和规定要求立即弃置电池。
* 无线产品发出的短波无线电频率信号可能会影响其它电子设备和
医疗设备的正常使用。
* 在医疗机构内、 其它自控设备附近,* 在距离电子起搏器或其它医疗设备20cm的范围以内, 产品,无线电波可能会影响电子起搏器或其它医疗设备的正常使用。
也不要将本产品浸入任何液不要将物体塞入本产品的通风口或那有可能会使您触及危险电。
三、使用耳机通话 1、基本通话操作功能取消呼叫接听来电拒接来电结束通话增加音量减少音量通话传手机通话传耳机麦克风静音取消静音语音拨号末码重拨注意:● 当耳机音量调至最大时,● 耳机处于静音状态时, ‘嘟嘟’提示音。
● 部分手机按接听键接听来电时, 此时,您可以使用耳机的通话切换功能或在手机上操作, 将通话切换到耳机。
● 使用语音拨号时, 启状态。
2、三方通话操作功能接听新来电挂断当前通话接听新来电保留当前通话通话切换结束当前通话切换至保留的通话短按 键短按 键长按 键长按 键短按 键一次短按 键一次操作您会听到一提示音。
远程播放控制(上曲/下曲/暂停/恢复)功能,如下图所示,使用一条指示灯红蓝灯交替闪烁蓝灯每2秒闪1次蓝灯每4秒闪2次红灯代替蓝灯闪烁耳机状态配对状态未连接设备已连接设备低电量指示灯恢复出厂设置后,耳机的配对列表会被清除,当耳机再次开机后,会自动进入配对模式,不会再自动连接, 需要与设备连接,需重新配对。
恢复出厂设置确保耳机处于关机状态,在充电时长按音量+键约3看到红蓝灯同时闪时松开,同时响起提示音。
版本号Ver1.3地 址:北京市海淀区北四环西路68号生产商:东莞市漫步者科技有限公司厂 址:东莞松山湖高新技术产业开发区工业东路2号北京爱德发科技有限公司商标说明:EDIFIER , 均为北京爱德发科技有限公司持有注册商标,微信扫一扫,更多信息请勿将该耳机佩戴或放置在离心脏起搏器过近的位置(小于10CM)。
请勿将插头插入电源插座。
儿童应在成人监督下使用本设备,本产品并非玩具。
在高音量下使用耳机⸺特别是长时间使用⸺可能会对操作高保真音响开关或插入耳机时可能会发出尖利的声音,其在高音量设置下可能会影响您的听力。
因此,在切换各请将音量控制设置为最低。
驾驶时或骑自行车时请勿使用耳机。
一、简图二、充电该耳机使用内置可充电电池,首次使用耳机前必须给电池充满电。
使用中,若只有红灯闪烁且每5分钟响一串警告声时,表示电池电量低,您也需要对耳机充电。
无线麦克风A1-说明书(完整版)-中英文-中性成品:65x75mm 展开:585x75mm印色:K+K 正面反面无线麦克风A1-说明书(完整版)-中英文-中性成品:65x75mm 展开:585x75mm印色:K+K 正面反面This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.。
THANK YOU FOR PURCHASING THE MAGICO A1 LOUDSPEAKERS. THE A1 INCORPORATES ALL WE HAVE LEARNED IN THE PAST TWO DECADES ABOUT LOUDSPEAKER DESIGN AND MANUFACTURING. LIKE ALL MAGICO LOUDSPEAKERS, THE A1 IS A PRECISION INSTRUMENT FOR MUSIC REPRODUCTION. PROPERLY SET UP AND MAINTAINED, IT WILL PROVIDE YOU WITH A GREAT MUSICAL EXPERIENCE FOR MANY YEARS. BEFORE UNPACKING AND PLAYING YOUR SPEAKERS, PLEASE READ THE FOLLOWING MANUAL FULLY. IT WILL PROVIDE YOU WITH DIRECTIONS FOR PROPERLY SETTING UP, POSITIONING, CONNECTING, AND CARING FOR YOUR SPEAKERS. FOLLOWING THESE INSTRUCTIONS WILL ENSURE A SMOOTH INSTALLATION AND OPTIMUM SPEAKER PERFORMANCE. IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT YOUR AUTHORIZED MAGICO DEALER. MAGICO MAINTAINS A NETWORK OF DEDICATED DISTRIBUTORS WHO WILL BE ABLE TO HELP YOU, SHOULD YOU HAVE ANY PROBLEMS YOUR DEALER CANNOT RESOLVE. FOR THE LA T EST INFORMATION ON ALL MAGICO PRODUCTS, PLEASE VISIT OUR WEBSITE, I WISH YOU MANY HOURS OF LISTENING PLEASURE.KINDEST REGARDS,ALON WOLF, CEOMAGICO, LLCBERYLLIUMMATERIAL THE A1 USES A TWEETER EQUIPPED WITH A BERYLLIUM DOME, ALLOWING A FREQUENCY RANGE EXTENDING BEYOND 40kHz. IN ITS SOLID FORM, BERYLLIUM IS HARMLESS. HOWEVER, DUE TO ITS NATURE, CERTAIN SPECIAL PRECAUTIONS SHOULD BE OBSERVED TO AVOID EXPOSURE TO UNNECESSARY RISK, SUCH AS:•UNDER NO CIRCUMSTANCES SHOULD THE BERYLLIUM DOME BE SUBJECTED TO ANY FORM OF ABRASIVE ACTION.•IN THE UNLIKELY CASE OF DAMAGE TO THE DOME, OF ANY FORM, A WIDE PIECE OF ADHESIVE TAPE SHOULD BE IMMEDIATEL Y USED TO SEAL THE WHOLE FRONT SURFACE OF THE TWEETER. YOU SHOULD THEN INFORM THE DEALER WHO YOU PURCHASED THE PRODUCT FROM, SO THAT THE TWEETER CAN BE REMOVED AND REPLACED BY A PROFESSIONAL.•IF THE DOME IS DAMAGED IN ANY WAY, CAUSING LOOSE PARTICLES OF BERYLLIUM, THESE SHOULD BE CAREFULLY COLLECTED WITH THE USE OF ADHESIVE TAPE, PLACED IN A SEALABLE BAG, AND RETURNED ALONG WITH THE TWEETER.MAGICO A1 UNPACKING1.C UT TAPE AND OPEN BOX. WITH TWO POEPLE LIFT THE FIRST SPEAKER WITH ITS FOAM CAPS FROM THE BOX2.R EMOVE SHIPPING BAG AND TWEEETER GUARD FROM SPEAKER AND CHOOSE YOUR FOOTER OPTION.•R OUND FOOT (SHIPPED PRE-INSTALLED)•S PIKE WITH OPTIONAL FLOOR SAVER DISK (SHIPPED IN ACCESSORY KIT)• 5 DEGREE ANGLE STANDS (AVAILABLE AS UPGRADE OPTION)3.P OSITION SPEAKERSETUPPOSITIONING—A1s IN RELATION TO THE LISTENER•THE SPEAKERS AND THE LISTENER SHOULD FORM AN ISOSCELES TRIANGLE.•THE LISTENER SHOULD BE EXACTLY EQUIDISTANT BETWEEN THE TWO LOUDSPEAKERS. THE BEST WAY TO DETERMINE THIS IS WITH A PIECE OF STRING. PICK A FIXED SPOT AT THE LISTENING POSITION. RUN THE STRING FROM THIS SPOT TO THE FRONT OF THE TWEETER OF THE LEFT SPEAKER. REPEAT THE PROCESS FOR THE RIGHT SPEAKER. IT IS CRITICALLY IMPORTANT TO KEEP THIS DISTANCE PRECISELY THE SAME.CONNECTIONSCONNECTIONS SHOULD BE MADE WITH ALL ELECTRONIC EQUIPMENT (AMPLIFIERS, PREAMPLIFIERS) TURNED OFF. THERE ARE TWO TERMINALS AT THE BACK OF THE SPEAKER. THE TERMINALS ARE INSULATED TO ACCEPT A VARIETY OF CABLE TERMINATIONS FOR MOST APPLICATIONS AND TO PREVENT ANY LIKELIHOOD OF ELECTRICAL SHOCK, EVEN WHEN THE SPEAKERS ARE USED WITH THE HIGHEST POWERED AMPLIFIERS. DO NOT USE TOOLS TO TIGHTEN THE BINDING POSTS.BREAK-INA LOUDSPEAKER IS A MECHANICAL DEVICE AND AS SUCH REQUIRES AN EXTENDED INITIAL PERIOD OF NORMAL USE DURING WHICH A NOTICEABLE IMPROVEMENT IN SOUND QUALITY WILL OCCUR. DO NOT ATTEMPT TO ACCELERATE THE BREAK-IN PROCESS BY PLAYING SINE WAVES, TONE SWEEPS, BREAK-IN CDS OF ANY SORT, OR OTHER GENERATED SIGNALS.CARE:FOR ALUMINUM PANELS USE A LINT-FREE SOFT CLOTH (PROVIDED IN ACCESSORY KIT). FOR PAINTED SURFACES, USE A PRODUCT SUCH AS MEGUIAR’S PROFESSIONAL FINALINSPECTION 34. DO NOT USE CLEANERS THAT CONTAIN AMMONIA, STRONG SOLVENTS, OR ABRASIVE MATERIALS. USE OF THESE CLEANERS CAN DEGRADE, SCRATCH, OR DESTROY THE FINISH.SPECIFICATIONSDESCRIPTION: 2-WAY SEALED BOX ENCLOSUREDRIVER COMPLEMENT:1 x 1.1" BERYILIUM TWEETER1 x 6.5” 6.5” Graphene Nano-Tec MidbassSENSITIVITY: 85dBIMPEDANCE: 4 OhmsFREQUENCY RESPONSE: 35 Hz – 50 kHzRECOMMENDED POWER: 50 watt RMS (min) / 150 watts (max)DIMENSIONS: 15.6”H x 12”D x 8.5”W (39.62cm x 30.48cm x 21.59cm)WEIGHT: 45 lbs. (20 kg.)LIMITED WARRANTYDEAR MAGICO PURCHASER,THIS PRODUCT HAS BEEN DESIGNED AND MANUFACTURED TO THE HIGHEST QUALITY STANDARDS. HOWEVER, IF SOMETHING DOES GO WRONG WITH THIS PRODUCT, MAGICO, LLC AND ITS NATIONAL DISTRIBUTORS WARRANT THE REPLACEMENT OF DEFECTIVE PARTS INCLUDING LABOR (EXCLUSIONS MAY APPLY) IN ANY COUNTRY SERVED BY AN OFFICIAL MAGICO, LLC DISTRIBUTOR. THIS LIMITED WARRANTY IS VALID FOR A PERIOD OF 5 YEARS FROM THE DATE OF PURCHASE. TERMS A ND C ONDITIONS1.THE WARRANTY IS LIMITED TO THE REPAIR OF THE EQUIPMENT. IN THE EVENT THAT THIS LOUDSPEAKER REQUIRES SERVICE, THE CUSTOMER MUST FIRST OBTAIN A RETURN AUTORIZATION FROM MAGICO OR ITS AUTHORIZED DISTRIBUTOR. THE CUSTOMER IS RESPONSIBLE FOR RETURNING THE LOUDSPEAKER TO MAGICO OR ITS AUTORIZED DISTRIBUTOR. IN THE EVENT THAT THE REPAIR IS DETERMINED TO BE UNDER WARRANTY, MAGICO WILL RETURN THE LOUDSPEAKER TO THE CUSTOMER AT NO CHARGE. EXCEPT AS INDICATED, NEITHER TRANSPORTATION, SHIPPING, NOR ANY OTHER COSTS, NOR ANY RISK FOR REMOVAL, TRANSPORTATION AND INSTALLATION OF PRODUCTS IS COVERED BY THIS WARRANTY.2.WITH THE EXCEPTION EXPLAINED BELOW, THIS WARRANTY IS ONLY VALID FOR THE ORIGINAL OWNER. IT IS NOT TRANSFERABLE. IT IS VALID ONLY WHEN PURCHASED FROM AN AUTHORIZED MAGICO DEALER. A VALID RECEIPT SHOWING THE PURCHASER’S NAME, DATE OF PURCHASE, AND DEALER INFORMATION MUST BE SUBMITTED WITH ALL WARRANTY CLAIMS.3.IN THE EVENT THAT THIS LOUDSPEAKER IS PURCHASED AS A USED OR TRADE-IN LOUDSPEAKER FROM AN AUTHORIZED MAGICO DEALER OR DISTRIBUTOR, THE SECOND OWNER SHALL RECEIVE THE BALANCE OF THE ORIGINAL WARRANTY BASED UPON THE ORIGINAL DATE OF PURCHASE. VALID RECEIPTS SHOWING THE PURCHASER’S NAME, DATE OF PURCHASE, AND DEALER INFORMATION FOR THE CURENT OWNER AND THE ORIGINAL PURCHASE MUST BE SUBMITTED WITH ALL WARRANTY CLAIMS.4.THIS WARRANTY WILL NOT BE APPLICABLE IN CASES OTHER THAN DEFECTS IN MATERIALS AND/OR WORKMANSHIP AT THE TIME OF PURCHASE AND WILL NOT BE APPLICABLE FOR DAMAGES CAUSED BY INCORRECT INSTALLATION, CONNECTION OR PACKING, FOR DAMAGES CAUSED BY ANY USE OTHER THAN CORRECT USE DESCRIBED IN THE USER MANUAL, NEGLIGENCE, MODIFICATIONS, OR USE OF PARTS THAT ARE NOT MADE OR AUTHORIZED BY MAGICO, LLC, FOR DAMAGES CAUSED BY FAULTY OR UNSUITABLE ANCILLARY EQUIPMENT, FOR DAMAGES CAUSED BY ACCIDENTS, LIGHTNING, WATER, FIRE HEAT, EXTREME WEATHER CONDITION, WAR, PUBLIC DISTURBANCES OR ANY OTHER CAUSE BEYOND THE REASONABLE CONTROL OF MAGICO, LLC AND ITS APPOINTED DISTRIBUTORS, FOR PRODUCTS WHOSE SERIAL NUMBER HAS BEEN ALTERED, DELETED, REMOVED OR MADE ILLEGIBLE, IF REPAIRS OR MODIFICATIONS HAVE BEEN EXECUTED BY AN UNAUTHORIZED PERSON.5.THIS GUARANTEE COMPLEMENTS ANY NATIONAL/REGIONAL LAW OBLIGATIONS OF DEALERS OR NATIONAL DISTRIBUTORS AND DOES NOT AFFECT YOUR STATUTORY RIGHTS AS A CUSTOMER.6.UNAUTHORIZED DISMANTLING OF THIS PRODUCT WILL RENDER THIS WARRANTY VOID.7.MAGICO, LLC STRIVES TO MANUFACTURE THE VERY FINEST POSSIBLE EQUIPMENT, AND THEREFORE RESERVES THE RIGHT TO MAKE CHANGES OR IMPROVEMENTS WITHOUT NOTICE.SERIAL NUMBERSPLEASE TAKE THE TIME TO RECORD YOUR SPEAKERS’ SERIAL NUMBERS BELOW.DISCLAIMERMAGICO, LLC MAKES THIS MANUAL AND THE CONTAINED INFORMATION AVAILABLE ON AN "AS IS" BASIS. ALL WARRANTIES AND REPRESENTATIONS OF ANY KIND WITH REGARD TO SAID INFORMATION IS DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE. UNDER NO CIRCUMSTANCES WILL MAGICO, LLC, OR ANY OF ITS OFFICERS OR EMPLOYEES BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES EVEN IF APPRISED OF THE LIKELIHOOD OF SUCH DAMAGES OCCURRING. MAGICO, LLC DOES NOT WARRANT THE INFORMATION AGAINST DEFICIENCIES OF ANY KIND.COMPANY INFORMATIONMAGICO, LLC3170 CORPORATE PLACEHAYWARD, CA 94545USAPHONE: +1.510.649.9700FAX: +1.510.323.4774EMAIL: ***************BUSINESS HOURS: 8AM - 4PM PACIFIC TIME© 2019 MAGICO, LLC。
Soundcore Life A101 EN•Fully charge both the earbuds and the charging case before the first use.1. Place the earbuds in the charging case and close it.2. Connect the charging case to the power supply by using a USB-C charging cable.Alternatively, position the charging case at the center of your wireless charger for wireless charging.The LED indicators on the charging case indicate the charging status.> 70%30% - 70%< 30%100%21orWearing1. Choose the EarTips and EarWings that fit your ears best.2. Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position.Your earbuds come with multiple pairs of EarTips and EarWings, among which Medium-sized are pre-installed.Powering On/OffThe earbuds will automatically power on when taken out of the charging case.The LED indicator on earbuds will light up white for 1 second.To power off, place the earbuds in the charging case.ON• The earbuds will automatically power off after 2 minutes if no device is connected.• To manually power on, press and hold the multi-function button on both earbuds for 1 second until the LED indicator turns white for 1 second.• To manually power off, press and hold the multi-function button on either earbud for 8 seconds until the LED indicator turns red for 1 second.EN 0203 ENBluetooth Pairing1. Take the earbuds out of the charging case, the earbuds will automatically enter the Bluetooth pairing mode.The LED indicator on one earbud will flash white.2. Select “Soundcore Life A1” on your device’s Bluetooth list to connect.When successfully connected, the LED indicator on earbuds will flash white once every 5 seconds.12SoundcoreLife A1SoundcoreLife A11s•When earbuds are out of the charging case and powered off, to manually enter Bluetooth pairing mode, press and hold the multi-function button on both earbuds for 3 seconds.• Each time you power on your Soundcore earbuds, they will automatically connect to your last successfully connected device if available within the Bluetooth range.• Mono mode: When Bluetooth connected, you can use either one of the earbuds only by placing the other one into the charging case.• When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.• When you are on a call, place either one of the earbuds into the charging case, the microphone in the other earbud will be activated.•The right earbud is the primary earbud by default. If you want to change this, remove the right earbud from your ear and place in the charging case, the microphone in the other earbud will be activated and become the primary earbud.ControlsResetYou might need to reset your earbuds if you experience any connectivity problems or function issues.1. Place the earbuds in the charging case and make sure they are being charged.2. Press and hold the button on both earbuds for 8 seconds until the earbud LED indicators flash red for 3 times.EN 043. Take the earbuds out of the charging case and wait until the LED indicator on one of the earbuds flashes fast while the other breathes slowly. This confirms that the reset was successful and your earbuds can be connected normally.x3x38s SpecificationsSpecifications are subject to change without notice.Rated output power 5 mW @ 1% THDBattery capacity85 mA x 2 (earbuds);770 mA (charging case)Charging time 2 hoursPlaytime(varies by volume level and content)Up to 9 hours(T otal 35 hours with the charging case) Driver size8 mm x 2Frequency response 20 Hz - 20 kHzImpedance16 ΩWaterproof level IPX7Bluetooth version V 5.0Bluetooth range 10 m / 33 ft05 ENEN 06。
MS50AWIRELESS SPEAKER User manual• MS50A is an active speaker using both W i-Fi and Bluetooth wireless technologies. The core application is online streaming media playback based on Amazon Alexa (W ork with Alexa). After registering this speaker to Amazon Alexa with an Amazon account, you will be able to use streaming services such as Spotify, Amazon Music, Pandora, etc. The speaker can be controlled in Alexa App as well as using interactive voice devices such as Echo. W ith Alexa, you can create your personal playlist, control play/ pause, build a multi-room system with other devices, and build two speakers to a stereo group.Thank you for choosing EDIFIER! For correct operations, please carefully read this manual before use.• Information contained herein may be subject to change from time to time without prior notice.Note:• The MS50A is compatible with Apple AirPlay.• This speaker can be connected to phones, PC, etc. for wireless playback via Bluetooth.• You can refer to the Quickstart Guide (included in the box) to set1. Product overviewOpen the box and ensure the following items are included:SpeakerQuickstart guide Power cable• Please use the power cable included in the box.2. What’s in the boxButton controls:① Mode switch:Press: audio mode switchPress and hold for 3s:Wi-Fi connection(Wi-Fi mode)Bluetooth pairing(Bluetooth mode)②Previous track ③ Next track④ Pause/playPress and hold for 6s:restore to factory settings ⑤ Power on/off / mute Press: mute/unmute Press and hold for 1.5s: power on/off ⑥ Slide counter-clockwise: volume down ⑦ Slide clockwise: volume up②①③④⑤3. OperationIndicators:StateBlink rapidlySteady litHeartbeat BlinkDescription 3 blinks per second Steady lit1 blink per second Long and short blinks alternativelyFunctions Ready to connect to a new Wi-Fi network Wi-Fi connected Wi-Fi disconnected Mute Blink rapidlySteady litBlinkSteady lit3 blinks per second 1 blink per second StateDescription Functions Mute Bluetooth pairing Bluetooth connected (1) White LED: Wi-Fi mode(2) Blue LED: Bluetooth mode 3s3s (3) Blue and white LED blinks alternately:starting up/ofre update (1) Unconnected to network: low brightness;(2) Connected to network:Day time (7am to 9pm): full brightnessNight time (9pm to 7am): low brightnessBrightness of indicatorsConnection:Bluetooth connection1. Power on this speaker and wait for it to start up (approximately 20 seconds). Press the " " button to switch to Bluetooth mode (blue LED).2. This speaker is in Bluetooth pairing mode when blue LED blinks rapidly, please select "EDIFIER MS50A" to connect.3. Blue LED will lit steadily after pairing is complete, now you can play music on the paired device.or tablet from the App Store/Google Play Store or from www;2. When powerenter W i-Fi connection mode (white LED blinking rapidly). To reset W i-Fi connection, press the " " button to switch to W i-Fi mode (white LED), then press and hold the " " button for 3s to enter W i-Fi connection mode again;device, and connect the speaker to network;4. Once connected, a steady white LED will be lit;5. This speaker can work with alexa, after it is connected to nrompt you to register this speaker to your Amazon Alexa account, please follow the instructions to complete the registration.Stereo group and multi-room system setup:Stereo group setup:You can use two MS50A to build a stereo group for better music experience.1. Make sure two MS50A speakers are connected to the same network as your mobile device;2. To setup stereo grreo group" on the home screen and click to add, then follow the instructions to build a stereo group;3. Set the two speakers as the left and right channel output respectively and rename the stereo group.4. To cancel the stereo grstereo group you want to cancel, and follow the instructions to cancel the stereo group.Multi-room system setup:After this speaker is registered in the Amazon Alexa, you can add it to a multi-room system through the Alexa App and play music/podcasts/news on multiple speakers simultaneously.1. Preparations: Connect this speaker to the same network as the other "work with Alexa" speakers, and ensure they are logged in to the same Amazon Alexa account.2. Setup: Open the Alexa App, switch to the Device interface, follow the instructions to join the existing multi-room system, or create a new multi-room system. Please see relevant instructions of the Alexa App for details.Stereo group and multi-room system setup:Music playback:2. Local playbackVolume control:1. Online steaming media playbackFor local playback devices, you can connect them to this speaker through Bluetooth for playback, or use Apple AirPlay or Spotify Connect to play through W i-Fi.The volume can be controlled in the following ways:(1) Touch panel on this speaker: In W i-Fi or Bluetooth mode, volume level can be controlled through the touch panel on this speaker, please see the touch panel control instructions;ready connected to network and enter the playing control interface for volume control;(3) Interactive voice devices: Under the same network, use the interactive voice devices like Echo logging in the same Amazon account to control volume through voice commands. (1) For Amazon Music, Spotify, Pandora, Tuneln, iHeartRadio and other music services linked to Alexa, after relevant accounts are linked, you can play through Alexa and control this speaker by using other interactive voice devices like Echo.youcan select to play on this speaker in the Spotify App;can be air-played by using iPhone, iPad, iMac and other devices.or there version code in the " " interface, and upgrade relevant System update and restore to factory settings Restore to factory settingsPress and hold the " " button on this speaker for 6s or click"Restor restore to factory settings, please note that W i-Fi connection, Bluetooth pairing and Amazon account registration information will all be cleared, meanwhile, this speaker will return to W i-Fi mode and the volume will resume to 50% level. System updateTroubleshooting 1. Check if the speaker is ON.2. Ensure the speaker is switched to Bluetooth mode.3. Disconnect from any Bluetooth device by pressing and holdingthe " " button, then search for "MS50A" again.4. Turn off the speaker and restart it, then switch to Bluetooth mode and search for "MS50A" again.No sound1. Check if main power is connected, or if the wall outlet is switched on.is set correctly on the speaker.3. Check if there is a signal output from the audio source.4. Try to turn up the volume using the volume control.5. Turn off the speaker and restart it.4. TroubleshootingPower output: mid-bass+treble: 25W+15WFrequency response: 52Hz-18KHzAudio input: Wi-Fi, BluetoothDeclaration for EUFrequency Band (Bluetooth): 2.402GHz ~ 2.480GHzFrequency Band (2.4G): 2.400GHz ~ 2.4835GHzFrequency Band (5G): 5.15GHz ~ 5.35GHz, 5.47GHz ~ 5.725GHz,5.725GHz ~ 5.85GHzRF Power output: ≤20 dBm (EIRP) (5.725GHz~5.850GHz excluded)RF Power output: ≤14 dBm (EIRP) (5.725GHz~5.850GHz)Model: EDF100008FCC ID: Z9G-EDF112IC: 10004A-EDF112P.O. Box 6264Hong KongTel: +852 2522 6989Fax: +852 2522 1989Printed in ChinaNOTICE:For the need of technical improvement and system upgrade, informationcontained herein may be subject to change from time to time without prior notice.Products of EDIFIER will be customized for different applications. Pictures and illustrations shown on this manual may be slightly different from actual product.If any difference is found, the actual product /support5. AppendixNote:。
移动多媒体音箱20. 话筒音量调节19. 话筒混响调节16. 音乐音量调节17. 高音调节18. 低音调节6. 话筒优先22. 无线话筒显示屏1. 首次开机默认为蓝牙输入,此时显示屏“ ”快闪,音箱自动进入蓝牙待连接 状态,打开蓝牙设备搜索并选择“EDIFIER D3-8s”,连接成功后显示屏“ ” 常亮。
2. 非蓝牙输入时,可短按控制面板上的“输入选择”按键切换至蓝牙输入,此时显示屏 “ ”快闪,音箱自动进入蓝牙待连接状态,打开蓝牙设备搜索并选择 “EDIFIER D3-8s”,连接成功后显示屏“ ”常亮。
3. 蓝牙模式下关机,再次开机音箱会自动回连最后一次连接的蓝牙设备。
4. 蓝牙连接状态说明注:1. 当建立蓝牙连接时,如需输入PIN码,请输入“0000”。
2. 为保证您能使用产品提供的所有蓝牙功能,请确保您的音源设备支持A2DP、AVRCP、HFP协议。
蓝牙连接●注:U盘/microSD(TF)卡支持的文件格式包括:MP3、WMA、WAV,支持最大采样率为48KHz,支持的最大容量为64G。
式,按键切换至U盘 中的音频文件。
充电● 在使用时,请阅读以下建议有助于您遵守保修条款,并延长产品的使用寿命。
●为减少火灾和触电危险,请勿让本产品淋雨受潮。
● 请不要在靠近水的地方使用本产品,也不要将本产品浸入液体中或将液体滴落、 泼溅到本产品。
● 请不要在靠近任何热源(如散热器、暖气设备、炉灶或其它产生热量的设备)的 地方安装和使用。
● 勿将产品放置在太阳晒射或者温度高的地方。
高温会缩短电子部件的使用寿命、 损坏电池、使某些塑料部件变形。
●勿将产品放在过冷的地方,以免损坏内部电路板。
●勿试图拆开产品。
如果非专业人员,可能会损坏产品。
●不要跌落、强烈振动、用硬体撞击产品,以免会损坏内部电路。
●勿使用烈性化学制品、清洁剂清洁产品。
● 不要用尖体在产品表面上乱划,以免损坏外壳和影响外观。
如果产品不能正常工作,请将其送至您的合格维修机构,工作人员会热心帮您解 决问题的。
Car DSP Ampli fier汽车数字DSP功率放大器使 用 说 明 书使 用 前 请 仔 细 阅 读项产DS612请全面阅读本用户手册,以熟悉设备各功能和特点,“漫步者”希望DS612带给您超越预期的听觉享受。
使用DS612出现任何问题请联系“漫步者”授权安装商。
• 避免在驾驶中对本产品进行任何操作。
• 为安全驾驶及保护听力请将音量设置到以能听清车外鸣笛为准。
• 请勿私自维修、改造本产品。
• 请使用符合要求的汽车电瓶连接本产品(12V)。
• 务必使用符合载流要求连接线及保险丝(20A以内)。
• 本产品不宜在高潮湿、外漏环境中使用。
• 本产品采用机身散热,安装请充分考虑设备散热问题。
• 线缆连接检测无误后方可连接设备正、负极。
• 发现问题请立刻停止使用并切断与汽车电瓶连接。
• 请专业技师安装、调试本产品。
• 请使用认证附件产品完成安装。
• 本产品为大功率用电器,使用时请启动车辆,避免因用电过大造成车辆启动困难。
• 汽车DSP功率放大器一台 • USB连接线一条 • 16P专用线一条• 魔术胶贴一对 • 说明书一份• 高保真、高信噪比AB类功放• 多种保护电路(零电流电源反接保护、欠压保护、过压保护、抛负载保护、功放输出短路保护)• 12通道31段图示参数EQ均衡器• 6通道高电平信号输入、6路低电平输入、蓝牙输入、U盘无损播放、光纤输入、USB声卡• 8路功放输出、12路RCA输出• 采用双模蓝牙5.0芯片• 两种启动模式,开关选择ACC或高电平启动• 专用插头设计,即插即用,简单易装• 支持电脑软件和微信小程序两种调音方式注意事项项产品特点1汽车CD机专车专用线材汽车原车线束A. 启动模式选择开关(ACC/HIGH) HIGH:高电平音频信号启动、ACC:钥匙门开关启动B. 电源指示灯C. USB接口(用于连接电脑调音)D. 彩屏线控接口E. 光纤输入接口F. 音效模式指示灯G. 专用连接插座(电源输入/ACC/REM OUT/4通道高电平信号输入/功放输出)H. U盘无损播放接口 I. 蓝牙连接指示灯J. 12V电源输入,高电平CH5&CH6输入接口,高电平CH5~CH8输出接口K. 6路低电平输入接口L. 12通道线路输出(用于连接功率放大器或有源低音炮)注:1. 音源优先级输出:高优先级:蓝牙和U盘;低优先级:高电平,低电平,光纤,USB声卡;2. 蓝牙连接(当使用手机蓝牙播放音乐时,请进入手机蓝牙设置,选择蓝牙名“DS612”的配对连接); 当使用微信小程序调音时,请打开微信,扫描二维码进入小程序,点击主页面上的蓝牙连接按钮后23HI JK LG A B C D E F REM功放R E M 连接D S P R E M O U T产品中有害物质的名称及含量Jul2022年东莞市漫步者汽车电器科技有限公司印制输出功率:8x30W@4Ω / 8x45W@2Ω失真度:≤0.05%频率响应:20Hz-20KHz输入灵敏度:高电平输入0.05V~10V信噪比: 带静噪>110dB,不带静噪>101dB 输入电源:DC 14.4V产品尺寸:185.5(长)x182(宽)x50(高)mm 净重:约1.73Kg微信小程序调音45汽车音响产品保修卡东莞市漫步者汽车电器科技有限公司2022年7月注:说明书规格为210mm*140mm 页数:6P 材质:128G铜版纸 彩印/折叠式说明书。
漫步者音箱说明书篇一:漫步者S5.1漫步者S5.1音箱使用说明书1、后面板1线路输入前左后左中置后中FL SL CE SCFR SR SW N前右后右低音闲置2、后面板2线路输出前右中置前左FR+ CE+ FL+FR_ CE_ FL_SR+ SC+ SL+SR_ SC_ SL_后右后中后左注:+为红色-为白色友情提醒:不要用自带的场景模式,用自选的,如下低音炮:4 前置低音:4 中音:4 高音:-1用遥控器调整吧。
参数:功率放大器输出功率:低音箱:rms 90w(fo=50hz,thd=10%)中置、前置,环绕:25w×5(fo=1khz,thd=10%)功率放大器总谐波失真:thd+n[0.5%(每通道输出功率5w时)功率放大器频响范围:卫星箱通道:20hz~20khz低音通道:20hz~200hz输入接口:莲花(rca)线路输入线路输入阻抗:50k欧姆低音单元:8寸铝音圈防磁纸盆单元(外径210mm),阻抗4欧姆卫星箱:4寸(106mm)复合盆低音+1寸球顶高音扬声器,全防磁,阻抗8欧姆输入电源:ac~220v,50hz,600w低音箱箱体尺寸:270(宽w)×496(高h)×496(最大深度d)mm前置及后置卫星音箱箱体尺寸:150(宽w)×230(高h)×161(深d)mm(不含面网)中置音箱箱体尺寸:290(宽w)×140(高(转载自:小草范文网:漫步者音箱说明书)h)×140(深d)mm(不含面网) 包装箱:低音箱包装尺寸:600(宽w)×350(高h)×600(深d)mm低音箱包装总重量:约24kg卫星箱包装尺寸:645(宽w)×230(高h)×565(深d)mm卫星箱包装总重量:约18kg调节功能:调节方式:控制面板按键控制,遥控器遥控调节项目:总音量,范围0—60,精度1db中置、前置、环绕音量微调,范围-7—+7,精度1db前置通道高音,中音、低音音调调节,范围-7—+7,精度2db显示方式:荧光屏(vfd)篇二:漫步者S2.1MKII音箱产品S2.1MKII充满阳刚之气,RMS功率高达300W!由内而外均是超强配置,比普通“大功率家庭影院”更令人疯狂。
漫步者x3air使用說明書漫步者X3Air使用说明书一、产品概述漫步者X3Air是一款高性能的无线耳机,采用了先进的蓝牙技术,具有出色的音质和稳定的连接性能。
本说明书将详细介绍X3Air的使用方法和注意事项,帮助用户更好地了解和使用该产品。
二、产品特点1. 高音质:X3Air采用了先进的音频处理技术,提供出色的音质表现,让用户享受更纯净、逼真的音乐体验。
2. 稳定连接:X3Air采用了蓝牙5.0技术,具有更远的传输距离和更稳定的连接性能,用户可以在不同场景下自由移动,不用担心信号中断的问题。
3. 轻巧便携:X3Air采用了轻巧的设计,重量仅为5克,携带方便,适合各种户外运动和旅行。
4. 长续航:X3Air配备了高容量的电池,单次充电可支持长达10小时的播放时间,满足用户日常使用需求。
5. 触控操作:X3Air支持触控操作,用户可以通过简单的触摸控制播放/暂停、切换歌曲、调节音量等功能。
三、使用步骤1. 充电:首次使用X3Air之前,需要进行充电。
使用附带的充电线连接耳机和电源适配器,耳机指示灯会亮起并显示充电状态。
充电完成后,指示灯会熄灭。
2. 打开蓝牙:在手机或其他蓝牙设备上打开蓝牙功能,并确保蓝牙设备处于可检测状态。
3. 配对连接:长按X3Air上的电源按钮,耳机指示灯会快闪,进入配对模式。
在手机或其他蓝牙设备上搜索并选择"X3Air"进行连接。
连接成功后,耳机指示灯会停止闪烁。
4. 播放音乐:打开手机上的音乐播放器或其他音频应用程序,选择要播放的音乐,X3Air会自动连接并开始播放音乐。
四、注意事项1. 保持干燥:X3Air不防水,避免将其暴露在潮湿的环境中,以免损坏。
2. 适当调节音量:使用X3Air时,请避免长时间高音量的使用,以免对听力造成损害。
3. 定期清洁:定期清洁X3Air的外壳和耳塞,以保持其外观整洁,并避免灰尘或污垢对音质的影响。
4. 避免强烈撞击:请避免将X3Air与硬物或地面强烈碰撞,以免造成损坏。
Product description· · · · · · · ·This product is a home party audio product with novelappearance ,convenient operation and fashionable design .It is suitable for family gatherings ,small and medium -sized parties , outdoor tourism , outdoor gatherings , offices , etc . It can enjoy the music easily and joyfully anytime and anywhere . Rhythm . It can also provide excellent sound quality for your computer ,digital music , mobile phones and other audio -visual products .Bluetooth , mobile U disk , audio input interfaceBluetooth Version 4.2Maximum receiving distance 10 meters Touch button mode and remote mode control ,trend , fashion Support external U -segment wireless microphone to achieve synchronized K songSound control LED , mini RGB stage lightSupport cool K songs ,full name K songs and other software Clear high and low quality speakers ,enjoy beautiful listening musicBuilt -in large -capacity lithium battery , long battery life ,environmental protection , economy , and practicalThank you for choosing the Home Party audio produced by our company . In order to let you experience the product easily , we have detailed instructions for use . You can get the introduction of the product , how to use it , etc . before you use the machine .Please read the instructions carefully for reference during operation without notice when the content changes .Precautions:· · · · · · · In order for users to use this product correctly and ensure good performance , please read and follow Do not hit the host seriouslyPlease do not approach strong magnetic fields , electric fields Do not leave this product in a hot , humid environment , not to rainDo not place or store the main unit near highly humid places Do not use in woven or other flammable accessories to avoid firePlease avoid direct light or heat appliancesDo not disassemble , repair or modify①.②.③.④.;Volume plus button /previous button ⑤.Volume down button /next button ;⑥.Mini RGB stage light on /off; mode switching button ;⑦.;High /woofer speaker ⑧.;Voice -activated LED , mini RGB stage light ⑨.;Microphone input ⑩.;USB input .;Sound guide hole .Power charging socket ;Remote sensor location ;Press and hold the power on /off button; Power LED indicator ; ..Audio input Operation diagramtouch to play /pause button ;InstructionsLED lightRGBlight on /off; Mode switch buttonCharging precautionsBluetooth connection 1.When charging , the blue LED will in sequence , full of one LED light ,and so on .Stop flashing when the battery is saturated (4 blue LED lights , about 5-6 hours full ).2.Support playback when charging , support shutdown charging .3.When the battery is full ,the charging indicator does not flash . Only when the battery level indicator lights only 3 blue LED lights , the indicator will flash .4.When the battery is too low , it will automatically shut down , please connect the power supply in time .“cycle flash ” USB portInsert the U disk with the copied file into the USB port of the product .According to the rules of post -plug priority , the player will automatically switch to USB mode and play .Microphone interfaceThis product only supports U -segment wireless microphone .The microphone sound can be adjusted by the MIC +/MIC - button on the remote control . Volume plus button /Previous song button Press and hold the button for the volume and touch the previous button for the track . Sound modeSelect the sound mode (standard -pop -rock -jazz )by the corresponding button on the remote control , the default is the standard mode state.Audio input Stereo audio input interface for easy connection to audio and video products such as computers , digital , music players , mobile phones , etc .Volume down button /Next buttonPress and hold the volume down button and touch the next button for the track . When the battery is saturated , the power indicator will light four blue LEDs at the same time .As the battery power decreases ,the LED will gradually make the three LEDs not light until the last LED is “blinking”, indicating that the battery is not available .The electrical state , when playing only with the battery , will automatically shut down when the battery is low . In this case , you should connect the power adapter to charge it .1. Touch to turn on /off the RGB stage light , often press the mode switch ( - Audio Input ).2. Press the mode switch button on the remote control - "M " button to switch (Bluetooth - Audio Input ).1. Boot into Bluetooth mode , the default is to enter Bluetooth mode;2. Turn on the Bluetooth function of your mobile device (mobile phone , computer , etc .). Search for the Bluetooth device "LP -HiFi ";3. Manually click , the device will be automatically paired , and the connection will be successful .4. Successfully paired devices , automatically connect next time.1;2.LED :;3.MIC +:;4. MIC -:;5. ;6;;8.STADARD :;9.POP :;10.M :;11.ROCK :;12.JAZZ :;Power on/off button voice-activated LED, mini RGB stage light off / on microphone volume plus button microphone volume down button Play/Pause button The previous song button; long press the volume plus button Next button; long press the volume down button sound mode - standard mode Sound mode - popular mode mode switching sound mode - rock mode Sound Mode - Jazz Mode FIRST STEP SECOND STEPV+V-SpecificationsPower supply voltage: built-in lithium battery 16.8V DC power supply Charging voltage: DC 19V 2ARated capacity: 6000mASpeaker: 5.25" 4Ω30W*2 42.2mm 6Ω30W*2Signal to noise ratio: 86dbFrequency response range: 65Hz-1.1KHzLife time: 10-11HHost size: 290*240mmWeight: 4.5KgParts ListHome Party* 11pcs power adapter (including power cord)1pcs remote controlInstruction manual / warranty card *11 set of plastic feet (3, including soft rubber feet)U-segment wireless microphone 1 set (optional)。
声明:由于产品的不断更新发展,我们保留没有事先通知的情况下,对本公司产品进行变动、修改的 权利。
均为爱德发持有的注册商标。
我公司保留一切权利,仿冒必究。
其他所涉及的商标均属于其所有者。
EDIFIER Ramble Xemal Copyright 2018All Rights Reserved.Manual Edition 2.6, Apr. 2018Printed in China2018年爱德发印制版权所有,翻印必究本手册内所有图文,未经授权,严禁任何方式之全面或部分使用。
本手册为随机手册,不得转卖,散发。
2018年4月* 请仔细阅读本说明书并妥善保管以备将来参考。
* 请使用制造商指定的附件。
* 请按说明书的连接说明进行正确的安装。
* 建议在0-35℃的环境中使用本产品。
* 为减少火灾和触电危险,请勿让本产品淋雨或受潮。
* 请不要在靠近水的地方使用本产品,也不要将本产品浸入 任何液体中或将任何液体滴落、泼溅到本产品上。
* 请不要在靠近任何热源(如散热器、暖气设备、炉灶或其 它产生热量的设备)的地方安装和使用本产品。
* 本产品上面严禁放置任何装水的器具,如花瓶;也不要在 本产品上放置任何形式的明火,如点亮的蜡烛。
* 请不要堵塞本产品的开口处,不要将物体塞入本产品的通 风口或槽隙中,这样做会有起火或触电的危险。
* 请在本产品的周围留足空间,以便能够保持良好的通风(建 议5cm以上)。
* 请不要强行将插头插入端口中,连接前请检查端口是否堵 塞、 插头和端口是否匹配和方向是否正确。
* 为避免儿童误食所提供的配件(如尖钉),请将配件放在 儿童拿不到的地方。
* 请勿擅自打开或移开外壳进行维修,那有可能会使您触及 危险电压或导致其它危险。
无论本产品因何原因损坏,都 必须请专业维修人员修理,如电源线或插头损坏、液体溅 入或物 体落入、淋过雨或受过潮、不能正常工作或被摔过。
* 在用干布擦拭、清洁产品之前,请先将本产品关机,并拔下供电的插头。
漫步者A1说明书
一、产品概述
二、主要功能
1.高清音质:漫步者A1采用先进的蓝牙技术,支持高清音质的传输,让用户能够享受到逼真、纯净的音乐。
2.双耳通话:漫步者A1支持双耳通话功能,用户可以同时连接两个
耳机进行通话,实现更清晰、更方便的语音通信。
4.智能降噪:漫步者A1采用了先进的降噪技术,能够有效地减少外
界环境噪音对音乐和通话的干扰,提供清晰、纯净的声音。
5.长续航时间:漫步者A1内置了高容量电池,一次充电可提供长达
6小时的播放时间,让用户在旅途或者运动中持久地享受音乐。
6.单独使用:漫步者A1的两个耳机可以单独使用,每个耳机都具有
独立的按键和功能,方便用户在不同场景下的使用。
7.多设备连接:漫步者A1支持同时连接多个设备,用户可以轻松切
换音乐和通话,方便快捷。
三、产品配件
1.漫步者A1蓝牙耳机
2.充电盒
3.充电线
4.使用说明书
四、使用方法
1.打开盖子:首次使用耳机时,先打开充电盒的盖子,将耳机放入充电盒,并确保耳机与充电盒的金属触点对齐。
2.充电:连接充电线,将另一端插入电源插座,即开始给耳机充电。
充电盒有指示灯,在充电过程中会显示相应的充电状态,充满后自动停止充电。
3.连接手机:打开手机的蓝牙功能,附近的设备,选择漫步者A1进行配对,连接成功后,耳机即可开始使用。
充电注意事项:
1.请使用原装充电线和充电盒,以确保充电效果和安全性。
2.充电时请确保充电盒的金属触点清洁,以免影响充电效果。
3.充电盒有一定的防水性能,但请勿将其浸泡在水中。
五、产品维护
1.使用时请避免受到强烈的撞击或挤压,以免损坏耳机。
2.请保持耳机的干净,定期清洁耳塞和耳机的连接部分。
六、安全注意事项
1.使用过程中请注意交通安全,不要在驾车或者骑车时佩戴耳机。
2.长时间使用耳机时请适度调节音量,以免损伤听力。
3.不要将耳机和充电盒放在高温或者潮湿的环境中。
4.不要将耳机丢弃在火源附近或者暴露在阳光直射下。