爱国者f5002说明书

OPERATING INSTRUCTIONS MANUAL(Please retain for future reference)ForFVO-400 INDIRECT FIRED SPACE HEATERSCERTIFIED FOR USE IN CANADA AND U.S.A.As per CSA B140.8 Portable Oil Fired Heaters / CSA B140.02003 Oil Burning EquipmentConstruction Heaters Unattended Type.Issue date October 1, 2008FLAGRO INDUSTRIES LIMITEDST. CATHARINES, ONTARIOCANADAGENERAL HAZARD WARNING:FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER.WARNING:FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.WARNING:NOT FOR HOME OR RECREATIONAL VEHICLE USE.WARNING:INTENDED USE IS PRIMARILY THE TEMPORARY HEATING OF BUILDINGS UNDER CONSTRUCTION, ALTERATION, REPAIR OR EMERGENCIES ONLY.ALWAYS PROVIDE ADEQUATE VENTILATION. 1 SQ. IN. OF FRESH AIR MUST BE SUPPLIED FOR EVERY 1000 BTUH OF HEAT.THIS HEATER SHALL BE INSTALLED SUCH THAT IT IS NOT DIRECTLY EXPOSED TO WATER SPRAY, AND/OR DRIPPING WATER.This heater is designed and approved for use as aconstruction heater under CSA B140.8 Portable OilFired Heaters / CSA B140.02003 Oil Burning Equipment.We cannot anticipate every use which may be madeof our heaters. CHECK WITH YOU LOCAL FIRESAFETY AUTHORITY IF YOU HAVE QUESTIONSABOUT APPLICATIONS.Other standards govern the use of fuel gases and heatproducing products in specific applications. Your localauthority can advise you about these.SPECIFICATIONSModel …………………………………………………….…. FVO-400 Input …………………………………………………….…... 390,000 btuh Fuel …………………………………………………………. No.1, No. 2,diesel orkerosene Fuel Pressure …………………………………………….... 170 psi Nozzle ………………………………………………………. 2.25 x 45B (Delavan)Ignition ………………………………………………………. Direct Spark …….……………………………………………...…. ThermostatControlAir Circulation ………………………………………………. 2500 cfm Fuel Consumption ………………………………………...... 2.75 Gal/hr Approved …………………………………………………...... cETLus listedINSTALLATION:The installation of this heater for use with No.1, No.2, Diesel or Kerosene and shall conform with local codes or, in the absence of codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54. Installation of the unit shall be in accordance with the regulations of the authorities having jurisdiction or the CSA Standard B139.CLEARANCE TO COMBUSTIBLES:TOP FRONT SIDES REAR FLUE PIPE3 ft 10 ft 3 ft 3 ft 3 ft FUEL:This heater will operate with No.1, No.2, Diesel or Kerosene.Note:No.1 Fuel Oil or Kerosene must be used fortemperatures less than –10º C (8º F).ELECTRICAL:WARNINGElectrical Grounding InstructionsThis appliance is equipped with a three-prong (grounding)plug for your protection against shock hazard and should beplugged directly into a properly grounded three-prongreceptacle.115v supply must be available. Please note that the heaterrequires 15 amps for proper operation. Ensure appropriategauge extension cord is used.• 12/3 AWG at 50 Feet• 10/3 AWG at 100 FeetFLUE PIPE: Flue pipe connection must terminate with a vertical run atleast 2ft long.The vent outlet on the heater is 6” diameter. Certified ventingmust be used at all times. Vent cap should be installed insituations where downdrafts occur. All venting mustcorrespond with the CSA B149 standard or in its absence,local codes.FV SERIES CONSTRUCTION HEATER – VENTING REQUIREMENTS1. VERTICAL FLUE TERMINATIONSDFLUE OUTLET OF HEA TER2. HORIZONTAL FLUE TERMINATIONSFLUE OUTLET OF HEAALLA - VENT TERMINATION MUST BE A MINIMUM OF 2FT HIGHER THAN ANY POINTWITHIN 10FT.B - MAXIMUM HORIZONTAL RUN IS 30FT.NOTE: 90deg ELBOW = 10ft HORIZONTAL VENT ALLOWANCE45deg ELBOW = 5ft HORIZONTAL VENT ALLOWANCEC - VENT TERMINATION IN HORIZONTAL POSITION MUST BE MINIMUM 4ft FROM ANYCOMBUSTABLE SURFACED - EXTERIOR VERTICAL VENT TERMINATION MUST BE A MINIMUM OF 2ft.NOTE: ALL VENT TERMINATIONS MUST HAVE A RAIN CAP INSTALLED AS PER LOCAL CODE REQUIREMENTS.DUCTING: Canvas heater duct with a minimum temperature handling of300 deg F. including wire reinforcement to prevent collapsing.Heater is designed for use with 2 x 12” diameter ductsequipped with pin lock couplings (FV-D12).Install ducting to outlet on the heater using pin-locks providedon collar of ducting. Ducting should be inspected periodicallyfor tearing and/or wear marks. Ducting should be stored in adry area when not in useMAINTENANCE:1. Every construction heater should be inspected before each use, and atleast annually by a qualified service person. Incorrect maintenance my result in improper operation of the heater and serious injury could occur.2. Service and Maintenance only to be performed by a qualified service person.3. The hose assemblies shall be visually inspected prior to each use of theheater. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater being put into operation. The replacement hose assembly shall be that specified by the manufacturer.4. The flow of combustion and ventilation air must not be obstructed. Be sure tocheck the fan assembly and ensure that the motor and blade are operating properly.5. Compressed air should be used to keep components free of dust and dirt buildup. Note: Do not use the compressed air inside any piping or regulator components.6. Change fuel filter insert (Part# FVO-418) once per month. Change fuel filtercartridge (Part# FVO-419) once every 6 months.7. Change oil nozzle (Part# FV-435) once per year.8. Fan Limit Switch (Part# FV-407A) should be replaced if the fan motor does notshut off after the heat exchanger has cooled down.9. The High Limit Switches (Part# FV-406 & FV-437) should be checked eachseason. These limit switches will ensure the burner shuts down if the temperature exceeds 150º F at rear of unit and 290º F at the outlet.10. Fuel tank should be drained on a regular basis by removing drain plug.11. CAUTION – Do not have any source of ignition near the heater when drainingtank.NOTE: No.1 fuel oil or kerosene is recommended for temperatures below -10º C / 8º F11. Heat Exchanger should be cleaned if smokey conditions continue even afterthe air adjustments on the burner are made.START UP INSTRUCTIONS:1. Be sure the switch in is the “OFF” position.2. Ensure electrical cord is grounded and heater is on a level surface.3. Plug in supply cord to 115V 15amp outlet.4. Move switch to “MANUAL” position for manual control.5. Move switch to “THERMOSTAT” position for thermostatic control. Please Note:1. If using Thermostat on unit, unit must be started in Thermostat position.2 When changing between manual and thermostat operation, the heatermust be left in the “OFF” position for 30 seconds to prevent the burner from locking out.3. When using a generator for electrical supply, make sure the generatoris properly grounded and generator is at a 60Hz frequency.4. In the event that a Generator is being used and the generator runs out offuel, make sure the heater switch is in the “OFF” position before restarting generator, failure to do so may damage heater.TO SHUT DOWN:1. Move switch to “OFF” position.NOTE: Fan will continue to operate after the burner shuts down. Once the unit cools down, the fan will stop.IF HEATER FAILS TO START:1. Press manual reset button at rear of burner.2. Check fuel level. There must be 2-4 gallons of fuel in the tank for theheater to start properly.3. Make sure there are no air locks in fuel lines or filter.4. Ensure proper power supply and extension cord is being used.5. Check for dirty fuel filter or blocked fuel supply line.6. Check burner nozzle assembly.NOTE: IF THE BURNER HAS BEEN RESET SEVERAL TIMES THERE MAY BE AN ACCUMULATION OF OIL IN THE CHAMBER! DO NOT CONTINUE TO TRY AND START THE HEATER!DRAIN OIL FROM HEAT EXCHANGER USING DRAIN HOLE AT FRONT OF HEAT EXCHANGER FOR 15-20 MINUTES BEFORE ATTEMPTING TO RELIGHT. LET REMAINING EXCESS OIL BURN OFF BEFORE CHECKING COMBUSTION OF UNIT.SAFE OPERATION PRECAUTIONS:1. Do not fill fuel tank while heater is operation.2. Do not attempt to start heater if excess oil remains in the heatexchanger.3. Use switch to shut down the heater. Do not try to shut down the heaterby unplugging the electrical cord.4. Do not plug anything other that the thermostat into the “Thermostat”plug.5. Do not use any fuel other that those listed on rating plate.6. Follow electrical requirements shown on rating plate and/or Electricalrequirements section of this manual.7. Before removing any guards or performing any maintenance, be surethat the main power supply is disconnected.COMBUSTION AIR ADJUSTMENTS:NOTE: Proper combustion air adjustment must be achieved using a certified combustion analyzer and smoke tester to ensure completecombustion.The air adjustment should be made to achieve 10% CO2and No. 1 or “trace” smoke. (Bacharach Scale)SETTING THE AIR ADJUSTMENT PLATEA) Regulation of thecombustion air flow is madeby adjustment of the manualAIR ADJUSTMENT PLATE(1) after loosening the FIXINGSCREWS (2 & 3). The initialsetting of the air adjustmentplate should be madeaccording to Column 5 in theBurner Set-up Chart.B) The proper number on themanual AIR ADJUSTMENTPLATE (1) should line up withthe SETTING INDICATOR (4)on the fan housing cover.Once set, the air adjustmentplate should be secured inplace by tightening SCREWS2 and 3.C) The final position of the airadjustment plate will vary on each installation. Use instruments to establish the proper settings for maximum COand a smoke reading of zero.2NOTE: Variations in flue gas, smoke, COand temperature readings may be2experienced when the burner cover is put in place. Therefore, the burner cover must be in place when making the final combustion instrument readings, to ensure proper test results.BURNER SET-UP CHART1 2 3 4 5ACTUAL FIRING RATE± 5%NOZZLESIZEPUMP PRESSUREGPH GPH PSI BAR TURBULATORSETTINGAIRDAMPERSETTING2.75 2.25 x 45°150 10 54 - 6* Note – Air damper setting is typically set at 4 for operation in coldertemperatures. A combustion analyzer should always be used when setting the the burner.TEMPERATURE FEELER GAUGE ADJUSTMENT(ATTACHED TO FAN SWITCH)The temperature feeler gauge is required to be always touching the heater exchanger.The temperature feeler gauge controls the air flow over the fan switch, which eliminates any unnecessary fan cycling. The temperature feeler gauge can be adjusted for different outside temperatures, by rotating the location of the temperature feeler gauge holes. This will provide maximum performance of the unit in different applications.If supply air is warm (-5º C, indoor application):Turn the temperature feeler gauge so that the holes are parallel with the heat exchanger. This will help the fan switch to remain cool and not overheat. See following:If supply air is cold (under -5ºC):Turn the temperature feeler gauge so that the holes are closed off as the air goes over the heat exchanger. This will reduce fan cycling and the unit from shutting down. See following:In extreme cold conditions, cover the holes on the temperature feeler gauge using foil tape. Ensure that the temperature feeler gauge is readjusted for warmer weather conditions. Failure to do so may result in burning out fan switches- notcovered under warranty.ELECTRICAL CONNECTIONSIt is advisable to leave the control box off the sub-base while completing the electrical connections to the burner.The burner may be controlled using either a DIRECT LINE VOLTAGE control circuit (120V AC 60 cycle) OR a LOW VOLTAGE control (24V AC 60 cycle) using a R8038A Honeywell switching relay or equivalent.Using the appropriate diagram below, make electrical connections to the burner. All wiring must be done in accordance with existing electrical codes, both national and local.When all electrical connections have been made, the control box may be put back in place on the sub-base.WARNING: DO NOT activate burner until proper oil line connections have been made, or failure of the pump shaft seal may occur.APPLICATION FIELD WIRINGREMOTE SENSING OF SAFETY LOCKOUT: The SAFETY SWITCH in the 530SE CONTROL BOX is equipped with a contact allowing remote sensing of burner lockout. The electrical connection is made at terminal 4 (●) on the SUB-BASE. Should lockout occur the 530SE CONTROL BOX will supply a power source of 120Vac to the connection terminal. The maximum allowable current draw on this terminal (4) is 1 Amp.WARNING: If a neutral or ground lead is attached to this terminal, the CONTROL BOX on the burner will be damaged should lockoutoccur.INSERTION / REMOVAL OF DRAWER ASSEMBLYA) To remove drawer assembly, loosen SCREW (3), then unplug CONTROLBOX (1) by carefully pulling it back and then up.B) Remove the AIR TUBE COVER PLATE (5) by loosening the two retainingSCREWS (4).C) Loosen SCREW (2), and then slide the complete drawer assembly out of thecombustion head as shown.D) To insert drawer assembly, reverse the procedure in items A to C above, andthen attach fuel line to the pump.NOZZLE PLACEMENTA) Remove the NOZZLE ADAPTER (2) from the DRAWER ASSEMBLY byloosening the SCREW (1).B) Insert the proper NOZZLE into the NOZZLE ADAPTER and tighten securely(Do not over tighten).C) Replace adapter, with nozzle installed, into drawer assembly and secure withscrew (1).ELECTRODE SETTINGTURBULATOR SETTINGA) Loosen NUT (1), then turn SCREW (2) until the INDEX MARKER (3) is alignedwith the correct index number as per the Burner Set-up chart, on page 12.B) Retighten the RETAINING NUT (1)NOTE: Zero and five are scale indicators only. From left to right, the first line is5 and the last line 0.OIL LINE CONNECTIONSNote:Pump pressure must be set at time of burner start-up. A pressure gauge is attached to the PRESSURE PORT (8) for pressure readings. Two PIPE CONNECTORS (5) are supplied with the burner for connection to either a single or a two-pipe system. Also supplied are two ADAPTORS (3), two female 1/4” NPT, to adapt oil lines to burner pipe connectors. All pump port threads are British Parallel Thread design. Direct connection of NPT threads to the pump will damage the pump body. Riello manometers and vacuum gauges do not require any adaptors, and can be safely connected to the pump ports. An NPT (metric) adapter must be used when connecting other gauge models.。

For 200L openAir type (with filter ) cleaner for drum can Manual■APDQO-FItems1 ・・・・・・・For Safety1 ～3 ・・・・・・・Attention before the use4・・・・・・・Operation Conditions4 ～7 ・・・・・・・How to fix8 ・・・・・・・How to use9 ・・・・・・・Trouble shootingFilter Maintenance10 ～12 ・・・・・・・Specifications, ExternalDimensions and Part List13 ・・・・・・・Assurance & After ServiceFor Safety:・ This Manual covers important points for safe and correct operation.We request all the users/dealers/distributor to read this Manual carefully and understand correctly, before this Product is used. (Incorrect operation may result in troubles and/or accident)・ Be noted to keep this Manual properly, so that the Manual can be immediatelyread at any time, whenever needed.DangerWarningCautio nAttention before the useDanger○Operate the Product correctly, after the manual for liquid is carefully read.Warning････････････････････････････････････････････････････････････････････････････････○Operate at safe places only:Operate at safe places only, where no infants/children play.Keep watching while operated.････････････････････････････････････････････････････････････････････････････････○Contact a doctor:Whenever the operators feels uncomfortable during theoperation, immediately contact a doctor.････････････････････････････････････････････････････････････････････････････････○Wear the protectives:Always wear the protectives, according to the liquid manual. ････････････････････････････････････････････････････････････････････････････････○Do not disassemble, repair and/or remodel:Unauthorized person is not allowed to disassemble, repairand/or remodel the Product.････････････････････････････････････････････････････････････････････････････････○Always use new liquid:Whenever the liquid is changed, be sure to wipe previousliquid out, completely wash away, and then apply newliquid. Once the liquids are mixed together, chemicalreaction may be generated.････････････････････････････････････････････････････････････････････○Acceptable temp. for the liquid:Acceptable temp. for the liquid is 0-60℃.････････････････････････････････････････････････････････････････････Caution････････････････････････････････････････････････････････････････････････････････○Contact us for inspection or repairIn case the Product does not properly work or anythingabnormal is found, immediately stop the operation, andcontact your purchase shop for inspection or repair.Otherwise, it may cause an accident or injury.････････････････････････････････････････････････････････････････････････････････○Do not shock the Product:The shock may trouble normal function, and may causetrouble and/or liquid leakage.････････････････････････････････････････････････････････････････････････････････○After used, completely take the liquid in a cleaner out:The remained liquid may cause the rust, which may cause trouble or ruin the performance.○Remove the moisture in the pressed air:In case of handling the liquid, remove the moisture in the compressed air by air-filter. (Separately sold)○In case the product is moved or a person in chargeis changed:Always attach this Manual with the Product ortransfer together.○In case this Manual is lost or damaged:Please order to sales shop.○APDQO-F is for indoor application only:In case used outdoor, be sure to apply the cover or to operate in a hut, so that the product is protected from wind and/or rain.○The installer/seller of this Product is requested:To pass this Manual to the person in charge of the operation. ○Be sure to use the compressor with 5Hp or higher.（0.4～0.6MPa）○This Product is designed for a drum can applicationDo not use for any other applications.○If the air is filled in, the air is discharged from theexit mouth. Pay attention for its direction.○Just before the tank is full, the liquid may get outtogether with discharged air.○Be sure to use the hose with dia.3/8 or bigger:If the hose dia.is not big enough, the pressureis ruined, resulting in less performance.(The couple with 20PM is attached)3OperationOperation Condition1. Apply to 200L Open Drum can (JIS Specification)2. Supplying Air Pressure ：0.4～0.6MpaHow to Fix※ This product is packed.※ As total weight is 38.5Kg, be careful for handling, when fixed.Carry on fixing, according to the procedures ① to ⑩．① shows when unpacked.② Shows to fix the ejector and float portion as shown in ②.※ Open drum can is notattached.① ②EjectorFloatO Ring(P22A)③ Discharging pipe to be fixed.④ Place it on a drum can.※As the weight is 35Kgs,be careful for handling.⑤ Firmly fix the Product and a drum can with the band⑥ Unscrew 3 knobs and open the lid .⑥③④⑤Outside Lever Band One Side Long Nipple⑦Fix plate (filter) and O ring (P195) on filter (small) ,as below picture shows.Fix filter (small) and filter (large) in order.⑧Close the lid, and screw it with 3 knobs.Filter (Small)Filter (Large)Plate (filter)O Ring(P195)⑨Attach fix hose and hose band.⑩Connect the head of ball valve and discharging/suction pipe, and hose crip (large) to the hose.Then, fixing job is completed.How to use1.Make sure the lid is screwed with 3 knobs.2.Make sure supply pressure is strong enough(0.4～0.6Mpa).3.Supply the compressed air to the coupler of ①ejector ASSY.(Equivalent to NITTO-KOUKI 20PM)【Collection to a drum can→to stop】1.Connect a coupler (air hose, equivalent toNITTO KOUKI 20PM) to air coupler (B).2. Turn ejector (A) to IN side.3. Turn valve (C) to IN side.4. Open air coupler (B).5. Open ball valve(D).Then, the collection job is possible.6. Open ball valve (D)7. Close air coupler (B)Then, you can stop operation.【The discharge from a drum can→to stop】1. Connect a coupler (air hose, equivalent toNITTO KOUKI 20PM) to air coupler(B).2. Turn ejector(A) to OUT side.3. Turn valve (C) to OUT side.4. Open air coupler (B).5. Open ball valve (D).Then, you can start discharging.6. Close ball valve (D)7. Close air coupler (B)Then, you can stop the operation.As the pressure is kept in a drum can, keep ejector knob (A) to IN side.(D)(A)(C)(B)Trouble Shooting1.In case suction function does not work, make sure● If air-hose is firmly connected.● If air valve is open.● If a drum can is not deformed or damaged.● If a hose or filter is not clogged.2.In case suction volume is not much enough, make sure● If the pressure to the pump is strong enough (0.4～0.6Mpa).● If air valve is fully open● If viscosity is not too highIf anything unusual is found, be sure not to disassemble the Product. Please contact us or purchase shop.Filter MaintenanceFilter (small) (150μm) andfilter (large) (40μm) are kept inside.Open the lid, and take filter (small) andfilter (large) out, as right picture shows.As stainless is used, periodically washwith water, washing liquid, or air blow etc.※Always wear protection glasses, and carefullytake care of splashing maching dust etc.SpecificationsExternal DimensionParts List:Assurance・After ServiceThank you for choosing our product. Our product is produced strictly under our regulations and quality control. However, if any of the defects, related with our production processes, is found, our assurance covers, according to the below limitation.1.To repair:To order the parts or request for repair, prepare to inform us Part No., Mfg No.,the purchased date with the receipt and then contact the purchased shop.2.Within 12 months after the purchased date, if the below case* happens, we willrepair it at free of charge.* Despite of regular maintenance and/or inspection specified in Manual, ifthe trouble or damage happens due to the defect of our design or assembling,within 12 months from the purchased date.※However, we are not responsible for all and any expenses or other damagesrelated with the above trouble and/or damage due to the defect of the product.※When the free repair is taken care, if the part replacement is judged necessaryby us, as the consumables, the expenses for such replaced parts shall be borneby the user.3.If the assurance period of 12 months is over, or the above assurance conditiondoes not meet even within the assurance period of 12 months, the repairing expenses shall not be covered by us, but borne by the user.(Also, in case our product is applied to other manufacturer’s product, we takeno responsibility and our assurance cannot be applied)4.In any case, delivery cost both to us and from us shall be borne by the user/customers.5.Exception from our responsibility (even within 12 months from purchased date)①Any problems, due to wrong handling (not following our Manual)②Any problems, due to repair, disassemble or remodel by a third party.③Any problems, due to improper storing or improper maintenance.④Any problem, without evidence to show the purchase of our product, suchas invoice or receipt etc.⑤Unusual part consumption, due to heavy uses.Contact the below for any question/request on the repair or after-servicewithin assurance period.。

爱国者无线硬盘 客户端软件使用说明V3.1目录免责声明 (3)特别提示： (4)一、设备的准备与连接 (4)1.1开机 (4)1.2 WiFi信号的连接 (4)1.2.1 Windows 平台 (4)1.2.2 iOS 平台 (5)1.2.3 Android 平台 (8)1.3移动网络存储服务器（移动NAS）模式 (12)二、客户端软件的安装 (13)2.1 Windows 平台 (13)2.2 iOS 平台 (14)2.3 Android 平台 (14)三、Windows客户端软件的界面说明 (17)四、iOS、Android客户端软件的界面说明 (18)4.1登录设备 (18)4.2 DLNA目录 (20)4.3文件播放 (22)4.3.1视频播放 (22)4.3.2音乐播放 (23)4.3.3图片浏览 (24)4.3.4文档浏览 (24)4.3.5 DLNA推送 (25)4.3.6 AirPlay功能 (26)4.4文件管理 (27)4.4.1分享按钮 (29)4.4.2操作按钮 (30)4.4.3传输按钮 (33)4.5设置界面 (35)4.5.1设备设置 (36)4.5.1.1无线设置 (36)4.5.1.2局域网设置 (38)4.5.1.3互联网设置 (39)4.5.1.4系统设置 (43)4.5.2来宾用户 (45)4.5.3缓存设置 (46)4.5.4语言设置 (46)4.5.5关于 (47)4.5.6注销 (47)五、使用第三方软件进行访问 (48)由于产品的更新，本手册中的图片和文字可能与您的设备中显示的图文略有不同，某些细微的变更将不会影响您的操作，请以实物操作为主。

一、感谢您购买爱国者无线硬盘产品。

在使用本产品之前，请认真阅读快速使用说明和本说明书。

当您开始使用爱国者无线硬盘产品时，爱国者电子认为您已经认真阅读了本说明书。

二、本产品为移动存储产品，用于用户数据的冗余备份，请用户在使用过程中及时对其中的数据进行备份。

警告感谢您购买了本公司的VICTOR5000电能质量分析仪，为了更好地使用本产品，请一定：——详细阅读本用户手册。

——严格遵守本手册所列出的安全规则及注意事项。

◆违规使用仪器可能导致触电、爆炸或火灾。

★任何情况下，使用本仪器应特别注意安全。

★注意仪器面板及背板的标贴文字及符号。

★使用、拆卸、维修本仪表，必须由有授权资格的人员操作。

★由于仪器原因，继续使用会带来危险时，应立即停止使用，并马上封存，由有授权资格的机构处理。

★仪表及手册上的“”危险标志，使用者必须依照指示进行安全操作。

★★当移除或更换电池或SD卡时，请确保断开测量导线、电流钳、电源适配器并关闭电源。

★电流钳必须与仪表对应连接，否则测试误差可能增大。

★如果电池或SD卡插槽缺失、被破坏或未正确安装，请勿使用仪器。

★任何与本仪器无关的系统安全问题，由该系统的建立、运营商负责。

★出于您的安全考虑，请仅使用随设备所附带的导线和配套附件(符合IEC61010-031(2002)标准)。

当低电压等级的传感器或附件连接至设备时，该低电压等级传感器或附件必须适用于该系统。

★使用前请经常检查测试导线、电流钳和附件处于最佳状况。

任一导线、电流钳或附件，如果绝缘受损(甚至只是部分受损)，都必须维修或报废。

★遵从环境状况。

(参阅15.3.1)★若环境需要，请使用个人安全保护设备。

★该仪器必须使用在对地交／直流电压不大于600V的第IV类装置设备(IEC61010-1标准)，或使用在电压不大于1000V的第Ⅲ类装置设备。

禁止在更高的电压网络或类型下使用。

★仅使用生产商所提供的电源适配器或电池组，它们具有特定安全等级。

★遵循附件或电流钳的安全级别限制，避免和未使用的终端连接。

★危险电压下某些电流钳不能从暴露的导体上安装或移除。

◆使用和连接步骤：★开启仪器。

★根据所需结果并参照网络类型设置仪器相关参数。

★连接电压测试导线和电流钳到仪器上。

★将地线和(或)中性线的电压测试导线连接到电网的地线和(或)中性线。

ADX2FD手持式发射机ADX2FD Frequency Diversity Handheld Transmitter User Guide Version: 7 (2019-D)Table of ContentsADX2FD手持式发射机3警告3 ADX2FD 手持发射机3特性3性能 3设计 4电源 4附带组件4选择以下 Shure 话筒拾音头之一 (1)： 4可选配附件4选配 Shure 话筒拾音头： 5 ADX2FD 发射机概览5发射机控制6主屏幕显示6锁定界面7 Shure 可充电电池7检查电池信息 8 Shure 充电电池保养和存储的重要提示 8电池安装 9 ADX2FD SB920 电池工作时间 9菜单参数9编辑菜单参数提示 10菜单地图 10菜单参数说明10无线电菜单 10音频菜单11工具菜单11红外同步12手动设置频率13射频静音13 Safe Start 14在频率分集模式下工作14关闭频率 2 (Freq 2) 14输入过载14音频发生器15匹配音频电平与话筒偏移15 ShowLink 测试16更新固件16固件版本 16更新发射机 16规格16频段和发射机射频功率19澳大利亚无线警告21许可信息21认证21 Information to the user 22•••••••••••••••••••◦◦•◦ADX2FD手持式发射机警告电池组可能爆炸或释放有毒物质。

火灾或烧伤风险。

不要拆开、挤压、修改、拆卸、或加热到 140°F (60°C) 以上或焚烧。

遵循制造厂商的说明只能使用舒尔充电器为舒尔可充电电池充电警告：换用不正确的电池可能出现爆炸危险。

只能更换相同的，或型号相当的电池。

禁止将电池放入口中。

如果吞入，请与外科医生或当地的毒物控制中心联系不要将电池短接，否则可能会导致烧伤或起火请勿使用或给非舒尔充电电池的电池组充电应正确处置电池。

联系当地供应商以正确处理用过的电池组。

南京奥视威电子科技股份有限公司型号：穿越500 Tx/500 Rx500ft/150m无线图传使用说明书感谢您选择奥视威电子产品使用前请仔细阅读本说明书Ver：B本产品的任何内部技术（包括硬件设备，软件设计，产品商标）均得到法律保护，任何侵犯本产品知识产权的行为，均将追究其法律责任。

本产品中所有本公司的品牌和商标均受到法律保护。

产品中所有涉及到的其他公司的品牌和商标均受到其拥有者的法律保护。

为了更好地为广大用户服务，本公司产品将持续改进和发展，本公司保留在不预先通知的情况下对本手册所述的产品进行修改和改进的权利。

用户在使用过程中发现问题或是对我们的产品有建议和要求，请通过电话、传真、电子邮件等方式与我们联系。

声 明南京奥视威电子科技股份有限公司地址：南京经济技术开发区恒通大道10号 210038电话：************传真：************Email：***********http：//本产品的质保期限为两年，以下情况不在质保范围内：⑴ 外观磨损等人为损坏；⑵ 未按说明书要求使用、维护、保管导致的产品故障或损坏；⑶ 在特殊环境内使用，导致的信号质量的衰减；⑷ 使用非产品配套的电源适配器而导致的产品损坏；⑸ 其它非产品本身设计、技术、制造、质量等问题而导致的故障或未经授权而私自进行拆卸、 维修或者是更换零件等操作。

请遵守本说明书安全注意事项，并在正确的方式下操作，本公司保证本产品能长久使用，但不包括以下情况：未经授权而私自进行拆卸、维修或者是更换零件等操作。

由事故造成的损坏，包含但不限于闪电、火灾、暴露于雨水或水气中。

使用的电源类型不在本产品的电压允许范围内。

安全注意事项警告请勿让任何液体溅到产品上。

为避免触电，请勿将产品上的通风孔堵住或粘贴住，勿拆开产品外盖，或将大头针、铁丝、异物放进通风口的缝隙内。

为减少触电或火灾的危险，请勿将本产品放置在雨中或潮湿处。

与任何设备连接之前，请先关闭电源，然后再操作。