cinvall燃气报警器说明书

家用燃气报警器使用说明书Company Document number：WUUT-WUUY-WBBGB-BWYTT-1982GT家用燃气泄露报警报警器安装使用说明书安装,使用产品前,请仔细阅读使用说明书,请妥善保管好本说明书,以便日后能随时查阅, 产品概述本产品采用高品质气体传感器，进口PIC芯片控制，安装简单接线方便，广泛用于家庭、宾馆、公寓、商场等存在可燃气体的场所进行了安全监控，可以测试天然气，液化石油气，城市管道煤气。

一、安装说明1.1、报警器安装位置：距离气源半径米范围内，通风良好处：（A）液化气比空气重，安装在距地面约0。

3米处（B）天然气、城市煤气、一氧化碳等比空气轻、安装在距天花板0。

3米处，1.2、禁止安装位置：墙角、柜内等空气不易流通的位置；易被油烟等直接熏到的位置。

1.3、禁止安装时间：（A）房屋未粉刷装修完，（B）刚装修完，房屋通风不足5天（C）在房屋内打造木制家具、或者购置新木制家具，其通风不足3天的（D）使用喷雾的灭虫剂（蚊、蟑螂。

）空气清闲剂、发胶、胶水。

的时间通风不足4小时的以上时间禁止安装报警器，若忆安装的，请为报警器断电，并用塑胶袋之类的东西将报警器保护起来，足通风时间后，才开户报警器。

以免损坏报警器的传感器，造成误报（没有气体泄漏而报警），或者出现黄灯闪烁，蜂鸣器滴叫故障，以至报警器报废。

因违规以上条造成的报警器损坏，则由使用者和安装者自行负责。

二、应用、电源灯：绿灯，工作状态常亮，报警时熄灭、报警灯：红灯，报警器亮起，停止报警时熄灭。

、故障灯、关阀灯：黄灯，故障状态时亮起，没有黄灯的，出现故障时则红绿灯交替闪烁。

接通电源，绿灯闪烁2-5分钟后，报警器进入正常工作状态，当所检测的气体达到报警点时，红灯常亮5分钟后报警器开始报警，绿灯熄灭，报警为常亮，蜂鸣器发出“嘀、嘀、嘀....”的报警声，当检测的气体的浓度下降到报警点以下时，报警器测停止报警。

按动测试健可模拟报警，报警灯亮起，同时蜂鸣器发出“嘀、嘀、嘀....”的报警声，若增加联排气扇功能，当报警器报警时，会启动排气扇，自动排除有毒气体，若加联机械手功能，当报警器报警时，已联接的机械手会自动关闭管道煤气阀，从而切断有毒气源。

希尔德燃气报警器说明书希尔德燃气报警器是一种用于检测室内燃气泄漏并及时报警的设备。

以下是一份可能的希尔德燃气报警器说明书：一、前言：此燃气报警器，可检测到天然气、煤气等易燃气体泄漏，当浓度达到警戒线时，燃气报警器会发出声音，提醒您及时关闭燃气阀门或采取应急措施，以确保您的生命财产安全。

二、技术参数：1. 燃气检测范围：天然气、煤气等易燃气体2. 探测原理：半导体传感器3. 报警浓度：天然气（10%LEL - 25%LEL）、煤气（≥0.1%）4. 报警音量：大于80分贝5. 工作电源：AC220V或DC9V电源6. 静态功耗：≤0.3W7. 报警输出：声光报警等8. 温度范围：-10℃ ~ 50℃9. 湿度范围：≤95%RH三、安装及使用：1. 安装方式：燃气报警器应安装在室内燃气管道附近或易燃气体泄漏可能较大的地方，并保证方便触发测试。

2. 室内燃气管道安装：（1）确认管道阀门关闭状态；（2）拧开燃气报警器底部的螺钉，并将燃气报警器底部固定在管道上；（3）确认底部灯亮，红灯亮表示未检测到燃气，绿灯亮表示燃气检测正常。

3. DC9V电池安装：按照燃气报警器底部的正负极标记安装电池，开启电源，将燃气报警器放置在易泄漏地点或易燃气体接触面前。

四、维护：1. 科学存放和使用，避免晒雨；2. 定期进行声音和检测的测试，如需要清洁请用清水擦拭；3. 电池电量低使用请更换电池；4. 如出现异常情况，请立即关闭电源和燃气阀门，并寻找专业人员进行检查，以免对人身财产造成危害。

五、注意事项：1. 请勿拆卸及修改燃气报警器；2. 请勿把电池放在高温、潮湿的环境下；3. 请勿用湿布擦拭探头和燃气报警器的外壳；4. 请勿安装在有风的地方或室外；5. 本产品需安装才能发挥正确的功能，严禁私自更改。

以上是一份可能的希尔德燃气报警器说明书，具体以实际产品说明书为准。

在使用燃气报警器时，一定要严格遵守操作规程，提高安全意识，确保生命财产安全。

燃气报警器使用说明书全文共四篇示例，供读者参考第一篇示例：燃气报警器使用说明书一、产品简介燃气报警器是一种用于检测室内有毒有害气体浓度的设备，主要用于检测燃气泄漏，保护家庭和工作场所的安全。

它能及时发现危险气体泄漏并发出警报提示，提醒人们采取相应措施避免事故发生。

二、产品功能1.检测功能：燃气报警器能够检测到室内的燃气浓度，如天然气、液化气等，并在浓度超过安全范围时发出声光报警信号。

2.报警功能：当燃气浓度超过设定值时，燃气报警器会发出高频响声，并闪烁警示灯，提醒用户及时采取安全措施。

3.自检功能：燃气报警器具有自检功能，可以定期检测探测器、报警器和电池是否正常运行，确保设备的正常使用。

4.报警静音功能：在确认燃气浓度不是真的危险时，可以通过按下消音按钮将报警器静音，以免误报警情况。

三、产品安装及使用1.安装位置：燃气报警器应该安装在离燃气源相对较近的地方，比如厨房、浴室等，且距离燃气源垂直上方一米之内。

同时应该避免阳光、潮湿、振动和尘埃的影响。

2.安装高度：一般建议燃气报警器安装高度不低于1.5米，离地面不低于1米。

3.电源供应：燃气报警器一般使用电池供电，安装时请查看产品说明书，使用相应规格的电池。

4.注意事项：请勿将燃气报警器安装在易燃易爆物品附近，也不要将它安装在通风不良的地方。

使用前请确认设备是否有损坏，并定期进行自检。

5.使用方法：使用时请按照产品说明书操作，正确打开或关闭开关，以确保设备正常运行。

在报警时请立即采取安全措施，开窗通风、切勿使用明火等，直至确定安全。

四、产品维护及保养1. 定期维护：请定期对燃气报警器进行清洁和维护，保持设备的敏感性能。

可用干净的湿布擦拭设备表面，确保传感器的敏感度。

2.更换电池：若燃气报警器在使用过程中出现电池电量不足的情况，应及时更换新电池，确保设备正常运行，避免因电源问题导致设备失效。

3. 报警测试：请按照产品说明书进行定期报警测试，确认设备功能正常。

燃气报警器使用说明书燃气报警器使用说明书如下：1. 安装位置：应安装在无显著摇动，无冲击振动和没有雨雪侵袭的地方，且介质中无足以腐蚀金属和破坏绝缘的气体和尘埃，更无爆炸危险。

2. 电源连接：采用系统12V供电时，外接端子红线接正极和黑线接负极。

3. 联网信号输出：白线：公共端；绿线：常闭触点；黄线：常开触点。

4. 排气扇和电磁阀的联接：将白线和黄线串联于排气扇开关的火线上；专用对接插头对接（输出12V脉冲电压，紧急切断电磁阀）。

5. 机械手的联接：报警器在检测状态下（阀门打开时），按一下按键，报警器就会关闭阀门，这种状态会有30秒延时。

延时过后，按一下按键，报警器会驱动机械手打开阀门，这种状态维持30秒后自动回到检测状态，这种状态是循环操作的（即按第一次是关阀，按第二次是开阀）。

6. 工作状态指示：电源指示灯长亮；报警指示灯亮一下；运行状态指示灯一闪一闪（此时设备在自检）大约1分钟后熄灭表示正常工作，如果长亮表示感应头出错，请等20分钟后重新上电。

探测器周围燃气浓度达到预设值时或短按测试按键注浸警指示灯长亮，并伴随发出报警声（自检时按测试键无效）。

7. 退出网关网络：在燃气报警器与网关正常连接的情况下，长按燃气报警器的退网键5秒，即可自动脱离Zigbee网络脂示灯由闪变为常亮。

8. 测试状态：黄色灯和红闪灯闪亮，表示报警器进入检测状态。

9. 预热状态：壁挂式接通AC220V或AC110V电源，绿色灯常亮，黄色灯灭，红色等闪亮，表明报警器处于预热状态。

10. 监视状态：预热约3分钟后，绿色指示灯常亮，表明报警器处于监视状态。

使用燃气报警器时应严格遵守使用说明书的要求，以确保安全。

如遇到问题或故障，建议联系专业人员或厂家进行维修和检查。

BC型报警箱简要安装调试说明书V1.11.性能优势及功能介绍2.产品框架说明3.压力管道部分安装说明4.集线部分安装说明5.压力显示报警部分安装说明6.工作参数的调整7.产品安装尺寸1.性能优势及功能介绍此款区域气体压力监测报警器适用于监测医院楼层、护士站、手术室、或实验室气体管道、特气钢瓶、汇流排、阀箱等区域供气压力的状况，通过0.8英寸数码管显示实时显示被监测气体的压力，可依据各参数使用需求设定报警点，并实现超限报警，确保区域供气压力的正常。

此款区域气体压力报警器设有RS-485通讯接口，可以通过网络实现与主报警箱及系统主机间的组网。

·主机供电电压：DC9V±5% MPa气压单位·电源适配器供电电压：AC100V～240VAC·默认低压测压范围：-0.1MPa～1.0MPa，可定制高压测压范围0MPa～25MPa·气压监测点数：1～7路·可连接总报警箱，实现对整个气体管路的实时监测，为数字化管理提供依据·0.8英寸数码管显示，压力值更直观，为维修提供具体的数值依据·摸感应式按钮，玻璃面板·支持传感器正负压通用，有效防止因误连接导致的传感器损坏·传感器可置于箱体内或远离箱体（有效距离1000米）方便布线和维修·传感器压力监测精度1.0级，监测压力范围-0.1Mpa-1.0Mpa·支持RS-485远程通讯，可跟情报面板对接·支持每路气压状态的开关量输出（代替电接点压力表）·支持整机状态的开关量输出·支持5米以内的红外遥控器静音·支持传感器故障检测·支持声光报警·支持蜂鸣器报警2.产品框架说明压力采集部分集线部分压力显示报警部分通讯部分如图所示，整个系统分为4部分：a.压力采集部分：将管道的气体压力通过“压力传感器”转化为标准的4-20mA 电流环向后传输压力信号。

气体报警控制器使用说明书（数码管）Ver1.1第1章产品简介1.1产品概述气体报警控制器是一款采用目前最新的数字化集成电路技术设计而成一款全新的智能化气气体报警控制器。

是一款单/双路信号输入控制系统，采用了大尺寸的高亮度数码管实时显示读数。

用户可通过简单设置进行现场检测与使用。

本系统主要应用于检测可燃气体或者有毒气体的场合，配合固定式气体检测仪使用，将气体检测仪检测到的气体读数汇总到显示屏幕上显示，同时根据设置当气体浓度大于报警浓度后，控制器将会进行一系列报警动作，例如声光报警、排风、断电等（依客户设置）。

1.2功能特点金属一体成型机身配套镜面显示屏，整体设计感大气又突出支持1-2路气体输入，支持两层报警点设置四路按键现场设置，设置系统由密码保护，有效防止错误操作。

支持声光报警设置，支持两路继电器控制，可联动排风、断电等行为一体化供电设置，配套气体检测仪不需要额外供电1一站式物联网供应平台1.3主要参数1.4设备外观如下图所示，产品主要由壳体、显示屏、报警灯、按键、挂钩等部分组成。

23第2章安装与接线2.1接线端子气体报警控制器的接线端子均已引到接线端子上，用户只需要在接线端子上接上线缆（自备）即可。

用户打开产品机壳后，在控制器下放可以看到一排接线端子（根据通道具体配置），如下图所示：端子序号端子作用2.2安装方式将气体报警控制器安装在距离地面2米左右便于45操作位置即可，注意控制器安装的位置应该方便走线，与各个传感器的距离适中即可。

下图参考设备采用壁挂安装的方式，提供两组壁挂挂片，使用M6螺母将壁挂片固定在背部突出的M6螺丝上即可。

两组壁挂孔之间间距为170mm ，如下图所示。

一站式物联网供应平台62.3连接设备取出购买的气体传感器，拧开正面的盖壳即可看到四组接线端子，使用0.3平以上的四芯铜线连接气体报警控制器与气体传感器即可。

注意连接距离不要超过500米即可。

接线方式如下图所示：7严格注意接线不能有误，否则会造成设备不可逆转的烧毁。

Page 3Page 4Page 2CO & Propane Gas Alarm for RVsRVCOLP-2 and RVCOLP-3Propane Gas Alarm for RVsRVLP-2 and RVLP-3Owner’s ManualGeneral WarningsPlease Read this Entire Manual BeforeUsing the RV Safe AlarmCarbon monoxide (CO) gases and propane, or liquefied petroleum (LP) can be dangerous. Propane is commonly used in recreational vehicles, and early detection of propane leaks can help prevent dangerous conditions. Carbon monoxide can also accumulate with improper ventilation or with malfunctioning appliances.RV Safe will only detect CO and propane gas present at the sensor. Gases may be present in other areas.This product is intended for use in recreational vehicles (RVs) only. It is not designed to measure compliance with Occupational Safety and Health Administration (OSHA) commercial or industrial standards.Warnings About Carbon Monoxide GasThis carbon monoxide alarm is designed to detect carbon monoxide and propane gas from ANY source of combustion. It is NOT designed to detect smoke or any other gases.Understanding the Dangers of CO Gas PoisoningThe following are the symptoms of carbon monoxide poisoning and need to be discussed with all occupants of the vehicle:1) Mild Exposure: Slight headache, nausea, vomiting, fatigue (“flu-like” symptoms).2) Medium Exposure: Severe throbbing headache, drowsiness, confusion, fast heart rate.3) Extreme Exposure: Unconsciousness, convulsions, cardiorespiratory failure, brain damage, and death.Many cases of reported CARBON MONOXIDE POISONING indicate that while victims are aware they are not well, they become so disoriented they are unable to save themselves by either exiting the building or calling forassistance. Young children and household pets are typically the first affected. If you experience ANY symptoms of CO poisoning, consult your physician.Potential Problem Sources of CO GasThe sources of carbon monoxide gas can be very difficult to locate due to the odorless, colorless nature of the gas, especially after the RV has been aired-out prior to the investigator’s arrival. Look closely at the following:1) Car idling nearby.2) Motorhome or generator exhaust entering RV .3) Excessive spillage or reverse venting of fuel-burning appliances.• Outdoor ambient conditions such as wind direction and/or velocity,including high gusts of wind; heavy air in the vent pipes (cold/humid air with extended periods between cycles).• Negative pressure differential resulting from the use of exhaust fans. • Simultaneous operation of several fuel burning appliances competingfor limited internal air.• Vent pipe connection vibrating loose from clothes dryer, furnace, orwater heater.• Obstructions or unconventional vent pipe designs which amplify theabove situations.4) Extended operation of unvented fuel-burning devices (range, oven, fireplace, etc.).5) Temperature inversions which can trap exhaust gases near the ground. 6) Poorly designed or maintained vents.Understanding the Dangers of Propane GasLiquefied petroleum (LP) gas is commonly called propane and is used as fuel for heating and cooking appliances, especially for RVs.Propane gas is explosive at the lower-explosive-limit (LEL), which is 21,000 parts per million (ppm). RV Safe will alarm at 10% LEL, or 2,100 ppm.Propane gas is denser than air, and will usually accumulate close to the floor. Therefore, RV Safe should be placed near the floor in order to quickly detect propane gas leaks.Supply Voltage Thresholds 8 to 15 VDC (13.5V nominal)Supply Current (Max) 70 mA at 13.5V / 95mA at 8V Supply Current (Typical) 17 mA at 13.5VOperating Temperature -40°F to 150°F (-40°C to 66°C) Humidity15% to 90%CO Detection Thresholds 70 ppm for 60 to 120 minutes (RVCOLP models only) 150 ppm for 10 to 30 minutes400 ppm for 4 to 15 minutes LP Detection Threshold 4200 ppm (<20% LEL)Audible Indicator 85 dB at 10 feet (Minimum)Alarm Lifetime 5 years (powered operation)Standards Conforms to RV Standards for:(All models)UL1484(RVCOLP models only) UL2034 and complies withCSA 6.19.01Warranty 1 Year Weight 1.3 ozDimensions 4.21”x 2.61”x 0.57”(10.7 cm x 6.6 cm x 1.4 cm)Note: Supply current will remain higher for 30 seconds after power-up.Alarm will not detect CO or Propane for the first 30 seconds.SpecificationsIf alarm horn sounds with a 4-chirp pattern (Model RVCOLP-2 and RVCOLP-3 only):1) Press the Silence/Test button.2) Call your Local Emergency Services number or 911. ______________________________________________Fill in your local Fire Department number here.3) Immediately move to fresh air – outdoors or by an open door/window. Do a head count to check that all persons are accounted for. Do notreenter the premises or move away from the open door/window until the emergency services responders arrive, the premises have been aired out, and your alarm returns to its normal state.4) After following steps 1 – 3, if your alarm reactivates within a 24 hour period, repeat steps 1 – 3 and call a qualified appliance technician at( ) ________________ to investigate for sources of CO and LP from fuel burning equipment and appliances, and inspect for proper operation of this equipment. If problems are identified during this inspection, have equipment serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturers’ instructions, or contact the manufacturers directly for more information about CO and LP safety and this equipment. Make sure that motor vehicles are not and have not been operating in an enclosed area near the RV .Note: This alarm was shipped with two (2) self-adhesive warning labels. Add the telephone numbers of your emergency service provider and that of a qualifiedtechnician in spaces provided. Place one label next to the alarm, and the other label near a source of fresh air where your family plans to gather if the alarm indicates the presence of carbon monoxide or propane gas.If alarm horn sounds with constant beeps:1) Evacuate everyone from the RV .2) Shut off propane gas supply at propane tanks or supply.3) Do not touch any electrical switch in or near the RV .4) Do not start vehicle’s engine or generator.5) Contact a qualified RV or gas technician for repairs.6) If you cannot reach a gas supplier or qualified Service Technician, contact the local fire department.7) Do not turn on gas supply until the leak has been repaired.WARNINGActivation of your CO alarm indicates the presence of carbon monoxide (CO) which can KILL YOU. WARNINGActivation of this device indicates the presence of propane gas, which can cause an explosionand/or fire. This normally indicates a leak in the propane gas pipes or a propane gas appliance. WARNINGTest alarm operation after vehicle has been in storage, before each trip, and at least once per week during use.WARNINGThis alarm has not been designed to detect smoke, fire, or gases other than carbon monoxide and propane.Alarm Features and FunctionsRV Safe includes an 85dB audible horn, two LEDs, and a Silence/Test button. The chart below summarizes the alarm outputs in each state. Normal Operation StateThe green power LED is ON when the alarm is functioning normally and no CO or propane gas is present. Press the Silence/T est button to perform a self test and enter the T est State.Note: Supply current will remain higher for 30 seconds after power-up. Alarm will not detect CO or Propane for the first 30 seconds and will draw extra current.Power Off StateIf no LEDs are on, then the alarm is powered off. Apply power to the alarm to resume normal operation.Self Test StateIf the Silence/Test button is pressed while in normal operation, the alarm will perform a self test of the CO sensor, propane sensor and battery voltage. It is recommended to perform a self test weekly, after power up from storage, and before each trip. If the self test passes, the alarm will perform 2 cycles of the CO horn pattern (4 rapid chirps followed by a 4 second pause), followed by 2 cycles of the propane horn pattern(constantly beeping). Refer to the Troubleshooting Guide for possible Self Test failures on page 7.CO Alarm State (RVCOLP models only)If CO gas reaches unsafe levels, the alarm will enter CO alarm state.The horn will sound with 4 rapid chirps followed by a 4 second pause and the red LED will flash rapidly. Open windows and doors and turn offappliances. Move to fresh air and call 911. The alarm may be silenced for 5 minutes by pressing the Silence/Test button. Contact a qualified RV technician to diagnose possible causes of CO.Propane Alarm StateIf propane gas exceeds 10% of the lower-explosive-limit for more than 30 seconds, the alarm will enter propane alarm state. The horn will sound with constant beeps and the red LED will be on. Immediately turn off all propane appliances and gas valve at the propane tanks. Open doors and windows to properly ventilate the RV . Check for any gas leaks and contact a qualified RV technician to diagnose possible propane leaks. The alarm may be silenced for 5 minutes by pressing the Silence/Test button.Alarm Silenced StateA CO alarm or propane alarm can be silenced for up to 5 minutes bypressing the Silence/Test button. The red LED will flash each second while the alarm is silenced. The original alarm state will resume after 5 minutes if the CO or propane levels still exceed safe levels.Low Battery StateIf the supply voltage drops below 8VDC, the alarm will enter Low Battery State. The horn will chirp every minute and both LEDs will flash every minute. Alarm performance cannot be guaranteed as the supply voltage drops below the low battery threshold. Charge or replace the RV battery immediately. DO NOT DISCONNECT THE ALARM.End-of-Life or other Failure StateIf the CO or propane alarm fails a self test, or if the End-of-Life is reached (after 5 years of operation), the alarm will enter the Failure State. The horn will chirp every minute and both LEDs will do a double flash every minute. Replace the alarm immediately.Alarm States CAUTIONDo not cover or obstruct RV Safe with anything that could prevent gas from entering the alarm.Page 5Page 7Page 8Limited WarrantyFor a period of 12 months from the date of purchase, RV Safe LLCLimited Warranty on your RV Safe alarm. Please retain it, along with proofof purchase showing the date of purchase and the identity of thepurchaser, in a safe place.REV 12.05.1990-4074-00CO sensors may not always activate and provide early enough warning. ACO sensor will only activate when it is maintained in working order andsufficient amounts of CO gas reaches the unit.If the RV will be used in areas where external CO sources such as portablegenerators or idling vehicles might be present, it is recommend that theRV's owner install additional CO alarms in the RV.Individuals with medical problems may consider using warning deviceswhich provide audible and visual signals for carbon monoxideconcentrations under 30 ppm.This device is designed to protect individuals from the acute effects ofcarbon monoxide exposure. It will not fully safeguard individuals withspecific medical conditions. If in doubt, consult a medical practitioner.WARNING - The installation of CO alarms should not be used as asubstitute for proper installation, use, and maintenance offuel-burning appliances, including appropriate ventilation andexhaust systems.CO ALARMS CANNOT GUARANTEE THAT YOU WILL NEVER SUFFER ANYILLNESS OR INJURY FROM EXPOSURE TO CARBON MONOXIDE GAS.WARNINGDo not install in a power line controlledby a wall switch or GFI circuit.Wire NutRear ViewRear ViewConnecting PowerDisconnect power until installation is completed to avoid shorting. RVSafe should be powered from the RV’s 12VDC system connected to aproperly fused circuit. Connect the red and black wires to the RV batteryusing an appropriate fuse (recommend using a 1A Min., 15A Max. fuse).3-wire models of RV Safe should connect the second red wire to anauxiliary 12VDC battery (such as the engine battery).Location — DO INSTALL• In the kitchen area near potential gas leaks such as a stove, oven,refrigerator, or furnace.• Within 4”-18” (10cm-46cm) of the floor. Propane is heavier than air andwill settle near the floor. CO gas is approximately the same density as air,and will mix evenly.•Where alarm vents are unobstructed to airflow; away from furniture,curtains, and out of closets.Location — DO NOT INSTALL• Within 12” (30cm) of opening windows, exterior doors, fans,vents, or areas with a draft.• On an exterior wall.• Within 24” (61cm) of any cooking appliance.• Behind furniture, drapes, in closets or areas that will block gas flow to alarm.• On a wall switch controlled by a power line, ground fault circuit or to acircuit breaker.MountingRV Safe should be mounted on a wall or panel of the RV.1. Ensure there is clearance for the wires and mounting screws behind thewall or panel.2. Drill a 5/8“ (16mm) hole for the wires and wire nuts to exit the alarmthrough the wall. Note that this hole is NOT the center of the alarm.3. Disconnect power from the 12VDC system being connected.4. Connect the wires of the alarm to the corresponding wires of the12VDC system using wire nuts. The black wire of the alarm should beconnected to ground, and the red wire connected to 12VDC power.3-wire models should connect the second red wire to 12VDC power of anauxiliary battery (such as the engine battery).6. Screw alarm to wall.Installing Your RV Safe Alarm• Water or splashesConditions That Could Adversely Affect Your Alarm。

家用燃气泄露报警报警器安装使用说明书安装,使用产品前,请仔细阅读使用说明书,请妥善保管好本说明书,以便日后能随时查阅, 产品概述本产品采用高品质气体传感器，进口PIC芯片控制，安装简单接线方便，广泛用于家庭、宾馆、公寓、商场等存在可燃气体的场所进行了安全监控，可以测试天然气，液化石油气，城市管道煤气。

一、安装说明1.1、报警器安装位置：距离气源半径1.5米范围内，通风良好处：（A）液化气比空气重，安装在距地面约0。

3米处（B）天然气、城市煤气、一氧化碳等比空气轻、安装在距天花板0。

3米处，1.2、禁止安装位置：墙角、柜内等空气不易流通的位置；易被油烟等直接熏到的位置。

1.3、禁止安装时间：（A）房屋未粉刷装修完，（B）刚装修完，房屋通风不足5天（C）在房屋内打造木制家具、或者购置新木制家具，其通风不足3天的（D）使用喷雾的灭虫剂（蚊、蟑螂。

）空气清闲剂、发胶、胶水。

的时间通风不足4小时的以上时间禁止安装报警器，若忆安装的，请为报警器断电，并用塑胶袋之类的东西将报警器保护起来，足通风时间后，才开户报警器。

以免损坏报警器的传感器，造成误报（没有气体泄漏而报警），或者出现黄灯闪烁，蜂鸣器滴叫故障，以至报警器报废。

因违规以上1.2 1.3条造成的报警器损坏，则由使用者和安装者自行负责。

二、应用2.1、电源灯：绿灯，工作状态常亮，报警时熄灭2.2、报警灯：红灯，报警器亮起，停止报警时熄灭。

2.3、故障灯、关阀灯：黄灯，故障状态时亮起，没有黄灯的，出现故障时则红绿灯交替闪烁。

2.4 接通电源，绿灯闪烁2-5分钟后，报警器进入正常工作状态，当所检测的气体达到报警点时，红灯常亮5分钟后报警器开始报警，绿灯熄灭，报警为常亮，蜂鸣器发出“嘀、嘀、嘀....”的报警声，当检测的气体的浓度下降到报警点以下时，报警器测停止报警。

2.5 按动测试健可模拟报警，报警灯亮起，同时蜂鸣器发出“嘀、嘀、嘀....”的报警声，2.6 若增加联排气扇功能，当报警器报警时，会启动排气扇，自动排除有毒气体，2.7 若加联机械手功能，当报警器报警时，已联接的机械手会自动关闭管道煤气阀，从而切断有毒气源。

Smoke Alarm Device User ManualModel number: FP510V Ref ：ST508EThank you for purchasing our smoke alarm device. Please take a few minutes to read the user’s manual thoroughly and familiarize yourself and your family with its operation. And save it for future reference.Diagram 2 will help you determine the correct location of safety products that will help make your home a safer place.Diagram 1Product Specifications:●POWER : built-in DC3V(CR123A) Lithium battery (battery not replaceable)●OPERATION CURRENT :<8uA (standby), <70mA(alarm)●ALARM VOLUME : >85dB(A) at 3 meters ●ALARM SENSITIVITY : 0.130-0.200dB/m ●SILENCE TIME: a pprox. 10 minutes●SMOKE ALARM DEVICE SOUND PATTERN :ISO8201(BI 0.5s - pause 0.5s – BI 0.5s – pause 0.5s – BI 0.5s – pause 1.5s, with the red LED flash, repeat this alarm pattern.)●COMPLY WITH: AS3786:2014Description:The unit is a photoelectric smoke alarm device. With the photoelectric technology, it is more sensitive to detecting slow smolder fires which general thick, black smoke, a little heat and may smolder for hours before bursting into flames. The smoke alarm device does not contain the radioactive material which is harmless to the environment.The smoke alarm device should be installed in every room (except the bathroom and kitchen), and every other area of the home, making sure the people in the home will be able to hear and respond to the alarm sound. For minimum protection, you should fit an alarm respectively for the hallways, living room, bedrooms and child rooms, each unit shall be placed in the middle of the ceiling of each room to protect.Typical single storey dwelling with recommended:Install a smoke alarm device on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area. If a bedroom area hallway is more than 30 feet long, install a smoke alarm device at each end. If there is a basement: install a smoke alarm device on the basement ceiling at the bottom of the stairwell.Typical multi-storey dwelling with recommended protection. Install a smoke alarm device on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area. If a bedroom area hallway is more than 30 feet long, install a smoke alarm device at each end install a smoke alarm device at the top of a first – to- second floor stairwell.Important Safety Information:1:The test button accurately tests smoke alarm device functions. Do not use any other test method. Test smoke alarm device weekly to ensure proper operation.2: If you're sure it isn't a really alarm, open windows or fan theair around smoke alarm device for silence it3: Observe and follow all local and national electrical andbuilding codes for installation.4: This smoke alarm device is designed to be used inside asingle family only. In multifamily buildings, each individual living unit should have its own smoke alarm devices. Do not install in non-residential buildings. And this smoke alarm device is not a substitute for a complete alarm system. 5: Install a smoke alarm device in every room and on everylevel of the home. Smoke may not reach the smoke alarm device for many reasons. For example, if a fire starts in a remote part of the home, on another level, in a chimney, wall, roof, or on the other side of a closed door, smoke may not reach the smoke alarm device in time to alert household members. A smoke alarm device will not promptly detect a fire except in the area or room in which it is installed.6: Smoke alarm device may not alert every household memberevery time. The alarm horn is loud in order to alert individuals to a potential danger. However, there may be some circumstances where a household member may not hear the alarm (i.e. outdoor or indoor noise, sound sleepers, drug or alcohol usage, the hard of hearing, etc.). If you suspect that this smoke alarm device may not alert ahousehold member, install and maintain specialty smoke alarm devices. Household member must hear the alarm’s warning sound and quickly respond to it to reduce the risk of damage, injury, or death that may result from fire, If a household member is hard of hearing, install special smokealarm devices with lights or vibrating devices to alert occupants.7: Smoke alarm devices can only sound their alarms when they detect smoke or detect combustion particles in the air. They do not sense heat, flame, or gas. This smoke alarm device is designed to give audible warning of a developing fire. However, many fires are fast - burning, explosive, or intentional, and others are caused by carelessness or safety hazards. In this circs, Smoke may not remake the unit alarm QUICKLY ENOUGH to ensure safe escape.8: Smoke alarm devices have limitations. This smoke alarm device is not foolproof and is not warranted to protect lives or property from fire. Smoke alarm devices are not a substitute for insurance. Homeowners and renters should insure their lives and property. In addition, it is possible for the smoke alarm device to fail at any time. For this reason, you must test the smoke alarm device weekly and replace unit every 10 years.Do Not Install Smoke alarm devices inthe Following Places:1: Near appliances or areas where normal combustion Regularly occurs (kitchens, near furnaces, hot water heaters). Use specialized smoke alarm device with unwanted alarm control for this areas.2: In areas with high humidity, like bathrooms or areas near dishwashers or washing machines. Install al least 10feet away from these areas.3: Near air returns or heating and cooling supply vents. Install at least 3 feet away from these areas. The air could blow smoke away from the detector, interrupting its alarm.4: In rooms where temperatures may fall below 5℃or rise above 45℃, or in humidity higher than 85%. These conditions will reduce battery life or cause a fault alarm.5: In extremely dusty, dirty, or insect – infested areas influence particles interfere with smoke alarm device operation.Operation:TestingTest the unit to ensure proper operation by pressing the test button, this will sound the alarm if the electronic circuitry, horn, and battery are working. If no alarm sounds, there is a defective battery or other failures, you can refer to “Trouble shooting” section for solution.DO NOT use an open flame to test your alarm, you could damage the alarm or ignite combustible materials and start a fire. CAUTION: Due to the loudness (85 decibels) of the alarm, Always stand an arms-length away from the unit when testing. Test the alarm weekly to ensure proper operation. Erratic or low sound coming from your alarm may indicate a defective alarm, you can refer to “Trouble shooting” section for solution. NOTE: WEEKLY TESTING IS REQUIRED.LED indicatorsRed LED-Flashing once every 40 seconds: indicates that the smoke alarm device is operating properly.Red LED-Flashing when the test button is pressed, or when the smoke alarm device senses particles of combustion and goes into alarm (constant pulsating sound), the red LED will flash once per second. The flashing LED and pulsating alarm will continue until the air is cleared or release test button.Red LED-Alarm silencer (Hush mode) indication: The red LED will flash once every 8 seconds, indicating the smoke alarm device is in the alarm silence (Hush) mode.Low battery indication - An intermittent “chirp” with red LED flashes once every 40 seconds: indicates that the smoke alarm device is low battery, you may press the test button for pause alarm for 10 hours, but it will reset automatically after 10 hours. Fault indication - The alarm chirp occurs every 40 seconds. NOTE: When the units chirp once every 40 seconds, you can press the test button temporarily for pausing this warning tone for 10 hours，it can still normally detect smoke during this period, it only removes nuisance warning tone. You can refer to “Trouble shooting” for solution, if there are still failures, you MUST replace it with a new alarm at once or contact you retailer during warranty.Alarm silence (silence mode)During the unit is alarming, you push the test button, it will be paused the unit alarming for approx 10 minutes. The red LED will flash once every 8seconds, it indicates the smoke alarm device is running into the silence mode. Smoke alarm devices are designed to minimize nuisance alarms. Combustion particles from cooking may set off the alarm if the alarm is located close to the cooking area. Large quantities of combustible particles are generated from spills or when grilling/frying. Using the fan on a range hood that vents to outside (non-recirculating type) will also help remove these combustible particles from the kitchen. The alarm silence (test button) is extremely useful in a kitchen area or other areas prone to nuisance alarms. The silence feature is to be used only when a known alarm condition, such as smoke from cooking activates the alarm.The smoke alarm device is desensitised by push the alarm Silence (silence mode) on the smoke alarm device cover, thealarm will silence to indicate that the alarm is in a temporarily desensitised condition.The smoke alarm device will automatically reset after approximately 10 minutes, if after this period, particles of combustion are still present, the alarm will sound again.The alarm silencer (silence mode) can be repeatedly until the air has been cleared of the condition causing the alarm. CAUTION: Before using the alarm silence， identify the source of the smoke and be certain a safe condition exists. NOTE: Dense smoke will override the alarm silencer and will sound a continuous alarm again.DANGER: If the alarm sounds, and it is not being tested, it means the unit is sensing smoke, THE SOUND OF THE ALARM REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.Maintenance and Cleaning:The alarm should be cleaned at least once a year·To clean your alarm, remove it from bracket on ceiling, you can clean it by using compressed air or a vacuum cleaner hose with a soft brush attachment. Blow or vacuum around the perimeter of the alarm to remove dust and dirt and debris. The outside of the alarm can be wiped with a damp cloth but you use a wet cloth in order to avoid water entering the inner of alarm.·After cleaning , reinstall it and test it by pressing the Test button. The alarm should be replaced if cleaning can’t restore the alarm to normal operation.·This alarm has a low battery monitor which will cause the alarm to “chirp” approx every 40 seconds and the red LED flash once at the same time for a minimum of thirty days when the battery gets low.If there is a defective battery or other failures, you can refer to “Trouble shooting” for solution, or deactivate this alarm to stop nuisance alarm which is caused by a failure of their function. If there are still failures during warranty, you can return to your retailer.Don’t paint the unit. Paint will seal the vents and interfere with the sensor’s ability to detect smoke.NOTE: 1.REGULAR WEEKLY TESTING IS REQUIRED!2.Must reactivate alarm before use if you deactivate it.Replacing the AlarmIt is recommended this alarm should be replaced ten years from the date of manufacture. This date has been provided on the product label which is located on the back of the alarm. WARNING: The battery is sealed in cover and not replaceable. Please replace another new alarm if the low battery chirp occurs. IMPORTANT: Do not attempt to remove the cover to clean inside. This will affect warranty.Repair:If the alarm is not operating properly, and is still underwarranty, return it to the original place you buy. Pack it in awell-padded carton, and ship to the original place you buy.If the alarm is no longer under warranty, please replace it immediately with a comparable alarm.Caution: Do not attempt to repair the alarm. It will affectyour warranty.Trouble shooting:Problem TroubleshootingSmoke alarm devicedoes not sound whentested.1.Must activate alarm beforeinstallation.2.Clean smoke alarm device.Please refer to the“maintenance and cleaning”section.3.if there are still failures duringwarranty, you can return toyour retailer.4. if the unit is out of warranty，please replace another new alarm.The alarm “chirp” withred LED flashes onceevery 40 seconds.The battery is under low batterystatus， please replace the smokealarm device.Smoke alarm devicechirp occurs every40 seconds（alarm goesinto fault mode）.Clean smoke alarm device. Pleaserefer to the “maintenance andcleaning” section. Purchase andchange another smoke alarm deviceif the problem still existSmoke alarm devicesounds, unwantedalarms intermittently orwhen residents arecooking, takingshowers, etc.1. Press test button to pause alarm.2. Clean smoke alarm device.Please refer to the “maintenanceand cleaning” section.3. Move smoke alarm device to newlocation and press test button.The alarm soundsdifferent from it is usedto. It starts and stops.1. Clean smoke alarm device.Please refer to the “maintenanceand cleaning” section.2. if there are still failures duringwarranty, you can return to yourretailer.3. if the unit is out of warranty，please replace another new alarm.How to deactivate the smoke alarm:Press test button and hold it for above 10 seconds until LED flashes rapidly (flash 5 times per second), then press Test button rapidly for at least 6 times within 5 seconds (or within during LED flashes rapidly), and the unit will generate a “beep” indicates the production goes into inactivation status There will be no any functions at this status, you must reactive it before use, Please refer to the chapter "installation" for activating the productNote:Deactivate this alarm if you need disposal it or stoppingnuisance alarm which is caused by a failure of their functionPractice Fire Safety:If the alarm sounds, and you have not pushed the test button, it is warning of a dangerous situation, your immediate response is necessary. To prepare for such occurrences, develop family escape plans, discuss them with all household members, and practice them regularly.1: Expose everyone to the sound of a smoke alarm device and explain what the sound means.2: Determine two exits from each room and an escape route to the outside from each exit.3: Teach all household members to touch the door and use an alternate exit when the door is hot, instruct them not to open the door if the door is hot.4: Teach household members to crawl along the floor to stay below dangerous smoke, fumes and gases.5: Determine a safe meeting place for all members outside the building.What to Do in Case of Fire:1: Do not be panic; stay calm.2: Leave the building as quickly as possible. Touch doors to feel if they were hot before opening them. Use an alternate exit if necessary. Crawl along the floor, and do stop to collect anything.3: Meet at a pre-arranged meeting place outside the building. 4: Call the fire department form outside the building.5: Do not go back inside a burning building. Wait for the fire department to arrive.Note:These guidelines will assist you in the event of a fire, however to reduce the chance that fires will start, practice fire safety rules and prevent hazardous situations.TOTAL HOME PROTECTIONDiagram 2Warranty Information:Company warrants to the original consumer.Purchase each new smoke alarm device to be free from defects in material and workmanship under normal use and service for a period of 10 years from the date of purchase. This warranty does not cover damage resulting from accident, misuse or abuse or lack of reasonable care of the product.In no case shall company be liable for any incidental orconsequential damages for breach of this or any other warranty express or implied ，whatsoever. The bad product can be mailed to the following address with a detail explanation of problem.Where is the best to be Installed:·Install the first alarm in the immediate area of the bedrooms. Install additional alarms to monitor the exit path, as thebedrooms are usually farthest from the exit. If more than one sleeping area exists, locate additional alarms in each sleeping are (see Diagram 3).·Install additional alarms to monitor any stairway as stairways act like chimneys for smoke and heat.·Install at least one alarm on every floor level ( see Diagram 4) ·Install an alarm in every bedroom.·Install an alarm in every room where large electricalappliances are operated (for example portable heaters ). ·Install an alarm in every room where someone sleeps with the door closed. The closed door may prevent an alarm located outside from waking the sleeper.·Smoke, heat, and combustion products rise to the ceiling and spread horizontally. Mounting the smoke alarm on the ceiling in the centre of the room places it closest to all points in the room. Ceiling mounting is preferred in ordinary residential construction.·When mounting an alarm on the ceiling, locate it at a minimumof 30 cm (12 in) from the side wall (see Diagram 5).·Put smoke alarm at both ends of a bedroom hallway or largeroom if the hallway or room is more than 9.1 m (30 ft) long.·Install smoke alarms no slopped, peaked or cathedral ceilingsbetween 500 and 1500mm from the highest point of theceiling. Smoke alarms in rooms with ceiling slopes greaterthan 1m in 8 m horizontally shall be located on the high sideof the room (See Diagram 6)Diagram 3Diagram 4Side wallDiagram 5Smoke alarm should be located between500 and 1500mm from the highest point.Diagram 6Installation:ActivationPress test button and hold it for above 3 seconds until LED lights, and release it within 2 seconds, the unit will generate a “beep” indicates that it is activated and goes into work statusCAUTION:MUST activate alarm first, or else there is no function for this unit.·Turn the alarm body counterclockwise and take off the bracket.·Press the bracket on the installation position, mark installation hole of the bracket with pencil.·Bore two installation holes on the sign with electric drill. Make diameter of holes is 5mm, Strike the two plastic plugs into holes with hammer.·Remove fixing plug from the bracket with screwdriver if necessary (See Diagram 7).·Attach the bracket to the plastic plugs and fix tightly the screws into the plastic plugs (See Diagram 8).·Fit the alarm on the bracket and turn the alarm body clockwise, until matching well on the bracket.·Insert fixing plug to the gap between bracket and bottom cover for fixing alarm if you want ( See Diagram 9).·Press the button for test the unit. The alarm sounds 3 beeps –1.5 seconds pause, repeat it until release the button, if nosound, it indicates a defective alarm, you can refer to ”Trouble shooting” for solution or return to your retailer during warranty.·If you have any questions on installation, you can contact your retailer.WARNING:To prevent injury, this unit must be securely attached to the wall or ceiling in accordance with the installation instructions.Diagram 7Diagram 8Diagram 9FirePro138–140 Bayfield Rd East, Bayswater North, VIC, 3153. Australia. P (03) 9720 4333F (03) 9720 4344。