下载文档原格式
常用铆钉性能数据一览表（全公制单位）安装力（KN）推力（N）扭力（N.m）安装力（N）推力（N）扭力（N.m）M31 1.0 5.8-8.4400 1.159.8-12.4550 1.5M32 1.47.7-10.3750 1.4712.7-15.31010 2.05M41 1.07.6-10.2470 2.614.3-16.9600 3.4M42 1.411.2-13.8970418.7-21.31250 5.1M51 1.08-10.64803.616.5-19.16204M52 1.412.7-15.3845 5.723.7-26.31112 6.8M61 1.4M622.3铆钉类型螺纹编码螺母的最大紧固扭矩（N.m）安装板厚度和材质安装板硬度HRb 安装力（KN）推力（N）扭力（N.m）拉出力（N）FH 1.6 mm 铝材297.8-104450.61891FHS 1.6 mm 铝材297.8-104450.51335FH 1.5 mm 钢材5910-12.28010.61891FHS 1.5 mm 钢材5910-12.28010.51335FH 1.6 mm 铝材2915.8-18757 1.12893FHS 1.6 mm 铝材2913.1-15.47570.92225FH 1.5 mm 钢材5918-20.21224 1.12893FHS 1.5 mm 钢材5919.8-2212240.92225FH 1.6 mm 铝材2915.8-18801 1.93783FHS 1.6 mm 铝材2914.5-16.7801 1.83449FH 1.5 mm 钢材5919.8-221335 2.33783FHS 1.5 mm 钢材5921.1-23.41335 1.83449FH 1.6 mm 铝材2920.2-22.5979 3.24450FHS 1.6 mm 铝材2918.9-21.1979 3.24183FH 1.5 mm 钢材5929.1-31.41669 4.55652FHS 1.5 mm 钢材5923.4-25.61669 3.25029FH 1.6 mm 铝材2923.4-25.61202 3.45429FHS 1.6 mm 铝材2923.4-25.612023.45429FH 1.5 mm 钢材5932.3-34.52003 6.86275FHS 1.5 mm 钢材5929.1-31.420035.76275FH 2.4 mm 铝材2827.8-3013807.310235FHS 2.4 mm 铝材2827.8-3013807.39345FH 2.2 mm 钢材4641.2-43.4255911.311348FHS 2.2 mm 钢材4643.4-45.6255911.311348FH 2.4 mm 铝材2827.8-30191411.310057FHS 2.4 mm 铝材2828.7-30.9191411.310057FH 2.4 mm 钢材4643.4-45.6289319.815464FHS 2.4 mm 钢材4648.7-51289319.813884铆钉类型螺纹编码螺母的最大紧固扭矩(n?m)安装板厚度和材质安装板硬度HRb安装力(kn)推出力(n)扭出力(n?m)拉出力(n)示意图FH 1.6 mm 铝材297.6-10.246512600FHS 1.6 mm 铝材2910.3-12.94650.81820FH 1.5 mm 钢材599.8-12.474012800FHS 1.5 mm 钢材5912.5-15.17400.81820FH 1.6 mm 铝材2911.6-14.2600 1.73150FHS 1.6 mm 铝材2911.6-14.2600 1.32570FH1.5 mm 钢材5913.4-168201.73840m2.50.41m30.74螺纹型号铆钉类型安装板材质5052-H34铝板冷轧板齿高安装板厚度(mm)16.5-19.1英制(UNIF IED)256示意图BS140010.224.4-27176011.90.3032 02432.74206.651813.64400.663218321.9FHS 1.5 mm 钢材5913.4-16820 1.32440FH 1.6 mm 铝材2914.3-16.9800 1.73780FHS 1.6 mm 铝材2914.3-16.9800 1.73445FH 1.5 mm 钢材5921-23.61335 2.83780FHS 1.5 mm 钢材5921-23.6133523445FH 1.6 mm 铝材2918.7-21.3975 2.94448FHS 1.6 mm 铝材2921-23.6975 2.94180FH 1.5 mm 钢材5927.6-30.21780 4.25650FHS 1.5 mm 钢材5925.4-281780 2.94775FH 1.6 mm 铝材2923.2-25.81070 3.55170FHS 1.6 mm 铝材2923.2-25.81070 3.54760FH 1.5 mm 钢材5932.1-34.72000 6.56270FHS 1.5 mm 钢材5931.2-33.82000 6.36000FH 2.4 mm 铝材2827.6-30.216607.310200FHS 2.4 mm 铝材2827.6-30.216607.39090FH 2.2 mm 钢材4643.2-45.8256011.311300FHS 2.2 mm 钢材4643.2-45.8256010.110600FH 2.4 mm 铝材2828.5-31.1191011.310500FHS 2.4 mm 铝材2828.5-31.1191011.39540FH 2.4 mm 钢材4643.2-45.8289019.215450FHS2.4 mm 钢材4648.5-51.1289017.513630铆钉类型螺纹编码螺母的最大紧固扭矩(n?m)安装板厚度和材质安装板硬度HRB max.安装力(kn)推出力(n)扭出力(n?m)拉出力(n)FH44400.7 1.5 mm不锈钢9238.9-41.22003 1.83560FH4632 1.2 1.5 mm不锈钢9241.2-43.42403 3.16008FH4832 2.4 1.5 mm不锈钢9248.7-513471 6.68010FH432 3.71.5 mm不锈钢9252.3-54.5467310.710013FH44207.9 1.5 mm不锈钢92101.2-103.5712017.617355FH4螺纹编码螺母的最大紧固扭矩(n?m)安装板厚度和材质安装板硬度HRB max.安装力(kN)推出力(n)扭出力(n?m)拉出力(n)FH4m30.9 1.5 mm不锈钢9238.7-41.32220 1.83500FH4m4 2.1 1.5 mm不锈钢9248.7-51.33210 6.58000FH4m5 4.3 1.5 mm不锈钢9251.7-54.3357510.710000FH4m67.2 1.5 mm不锈钢9269.7-72.3420015.914900铆钉类型螺纹编码齿高安装力(kn)推出力(n)扭出力(n?m)示意图2800.91401 1.12757 1.53757 1.50467 1.51556 1.721024 2.031024 2.00280 1.81423 1.92846 2.53846 2.50490 1.81579 2.321224 3.231224 3.20303 2.41467 2.629794.0英制(UNIF IED)公制(METRIC)英制(UNIF IED)256 3484406.7-8.911.1-15.663211.1-13.313.3-26.711.1-13.3m41.7m53.5m65.9m814.2公制(METR IC)m3.51.15安装板材质5052-H34 铝板冷轧板5052-H34 铝板冷轧板5052-H34 铝板S CLSS CLS3979 4.00490 2.91645 4.021268 5.131268 5.10303 2.91490 3.62846 5.731001 5.70534 3.61801 4.521113 6.831424 6.8铆钉类型螺纹编码齿高安装板材质安装力(kn)推出力(n)扭出力(n?m)02800.91400 1.132750 1.470470 1.471550 1.721010 2.030280 1.81400 1.922840 2.504801.815702.321210 2.30300 2.371470 2.62970404902.951645421250 5.1铆钉类型螺纹编码齿高安装力(kn)推出力(n)扭出力(n?m)030031480 3.62845 5.70530 3.61800 4.521112 6.80750 6.509707.9110.2214.109001011380132176017113.6218.1118.7220.31 132-50202036.2公制(METR IC)公制(METR IC)1.5mm 5052-H34 铝材1.5mm 冷轧钢测试安装板材质18-3832.7M1022-361760M818-32157027-361870M4M511.2-15.6M3.511.2-13.513.4-26.7M2 M2.5M36.7-8.9IED)024 03211.1-15.617.8-4083211.1-13.317.8-26.75052-H34 铝板冷轧板5052-H34 铝板冷轧板S CLSSS CLSS S CLSS CLSS CLS SS CLSSS CLSS CLS S CLS158027-3611.2-13.418-275052-H34 铝板冷轧板5052-H34 铝板冷轧板5052-H34 铝板冷轧板5052-H34 铝板冷轧板M618-325052-H34 铝板冷轧板安装板材质5052-H34 铝板冷轧板5052-H34 铝板冷轧板11.2-15.6安装力推出力扭出力安装力扭出力(kn)(n)(n.m)(kn)(n.m)钢材 3.8-6712 1.28.7-10.9 2.1不锈钢 3.8-6712 1.28.7-10.9 2.1铝材 3.8-6712 1.2钢材 6.5-8.71335 1.213.6-15.8 2.1不锈钢 6.5-8.71335 1.213.6-15.8 2.1铝材 6.5-8.71335 1.2钢材 6.5-8.71335 2.813.6-15.8 4.0不锈钢 6.5-8.71335 2.813.6-15.8 4.0铝材 6.5-8.71335 2.8钢材9.6-11.81780 2.816.7-18.9 4.0不锈钢9.6-11.81780 2.816.7-18.9 4.0铝材9.6-11.81780 2.8钢材9.6-11.81780 5.116.7-18.98.5不锈钢9.6-11.81780 5.116.7-18.98.5铝材9.6-11.81780 5.1安装力推出力扭出力安装力扭出力(kN)(N)(N?m)(kN)(N?m)钢材 3.6-6.2710 1.28.5-11.1 2.2不锈钢 3.6-6.2710 1.28.5-11.1 2.2 铝材 3.6-6.2710 1.2钢材 6.3-8.91330 1.213.4-16 2.2不锈钢 6.3-8.91330 1.213.4-16 2.2 铝材 6.3-8.91330 1.2钢材 6.3-8.91330 2.813.4-16 4.0不锈钢 6.3-8.91330 2.813.4-16 4.0 铝材 6.3-8.91330 2.8钢材9.4-121780 5.116.5-19.18.5 不锈钢9.4-121780 5.116.5-19.18.5 铝材9.4-121780 5.1最大记录值安装力推出力扭出力拉出力(N?m)(kN)(N)(N?m)(N)440 4.7523.4-25.61495.2 1.92670 6440 4.7541.2-43.42879.2 1.93026 6328.7541.2-43.42879.2 3.43026 86328.7545.6-47.84005.0 3.46194 8321845.6-47.84005.0 6.06751 323245.6-47.84005.08.06088最大记录值安装力推出力扭出力拉出力(N ? m)(kN)(N)(N ? m)(N)m30.5523.2-25.81493 2.362650 3.5m30.5541-43.62877 2.363025 m3.50.9141-43.62877 3.063025m4245.4-484003 6.346458m5 3.645.4-4840038.896226示意图SO4 和BSO4系列英制(UNIFIED) SO4 和BSO4系列公制(METRIC)测试安装板材质1.2mm 300 系列不锈钢测试安装板材质1.3 mm 300 系列不锈钢螺纹类型紧固扭矩值配套螺丝螺柱材质螺纹编码SO, SOS, SOa, BSO, BSOS, 和BSOa 系列公制(METRIC)螺纹类型紧固扭矩值配套螺丝m4, m52490 2490m3.51860 1860 (N)M31000 10003.5m318601860推出力测试安装板材质1.5 mm 5052-H34 铝材 1.5 mm 冷轧钢TSO, TSOS, 和TSOa 系列英制(UNIFIED)螺纹编码螺柱材质440 6440 632 8632 832, 032 2492 2492 2492 2492 1869 1869 (n) 1001.25 1001.25 1869 1869 推出力。
FEATURESAfter crimping, the conductor profile should measure the following.TerminalWire Size Crimp Height Pull Force Min.Series No. AWG mm2 mm In. N Lb.89.0 20.0.043-.0452477 18 0.801.09-1.1466.7 15.0.040-.0431.02-1.092477 20 0.5044.5 10.0.038-.0402477 22 0.350.96-1.0235.6 8.0.036-.0382477 24 0.200.91-0.9689.0 20.0.043-.0452478 18 0.801.09-1.1466.7 15.0.040-.0432478 20 0.501.02-1.09.038-.04044.5 10.00.96-1.022478 22 0.35.036-.03835.6 8.00.91-0.962478 24 0.2089.0 20.0.043-.0451.09-1.142878 18 0.80.040-.04366.7 15.01.02-1.092878 20 0.50.043-.04589.0 20.01.09-1.144838 18 0.8066.7 15.0.040-.0434838 20 0.501.02-1.0944.5 10.0.038-.0404838 22 0.350.96-1.0289.0 20.0.043-.0456438 18 0.801.09-1.14.040-.04366.7 15.01.02-1.096438 20 0.50.038-.04044.5 10.00.96-1.026438 22 0.35.036-.03835.6 8.00.91-0.966438 24 0.2089.0 20.0.043-.0451.09-1.146838 18 0.80.040-.04366.7 15.01.02-1.096838 20 0.50.043-.04589.0 20.01.09-1.148993 18 0.80.040-.04366.7 15.01.02-1.098993 20 0.5044.5 10.0.038-.0408993 22 0.350.96-1.0235.6 8.0.036-.0388993 24 0.200.91-0.96Pull Force should be measured with no influence from the insulation crimp.The above specifications are guidelines to an optimum crimp.PARTS LISTItem Order No Engineering No. Description Quantity11-40-2096 T8301AX Terminator (Fig. 1) REF1 11-40-4008 8301-2 Conductor Punch 1 Y2 11-24-1008 4995-12 Conductor Anvil 1 Y3 11-40-4007 8301-1 Insulation Punch 1 Y4 11-24-1009 4995-13 Insulation Anvil 1 Y5 11-40-4420 8301-22 Cut-Off Punch 1 Y6 11-24-1007 4995-10 Cut-off Insert 1 Y7 11-17-0109 1837-9 Terminal Drag Spring 18 11-40-4069 8302-103 Pivot Pin 19 11-40-4084 8301-9 Terminal Base and Track 110 11-40-4085 8301-10 Terminal Stop and Scrap Shield 111 11-40-4086 8301-11 Rear Cover 112 11-40-4087 8301-12 Terminal Drag Spring 113 11-40-4346 8301-8A Terminal Locating Block 114 11-40-4405 8301-21 Wire Stop Block 115 11-40-4406 8301-21A Wire Stop Blade 116 11-40-4419 8301-6A Cut-Off Punch 117 11-40-4421 8571 Punch Retainer 118 11-40-4458 8301-23 Stop Finger 119 11-40-4459 8301-24 Stop Finger Block 120 11-40-5142 8394-27 Cover Plate Extension 121 N/A N/A #2-56 by 1/4 Lg. SSSS 1**22 N/A N/A #2-56 by 1/4 Lg. SHCS 2**23 N/A N/A #5-40 by 3/16 Lg. BHCS 1**24 N/A N/A #6-32 by 1/4 Lg. BHCS 1**25 N/A N/A #8-32 by 3/8 Lg. BHCS 1**26 N/A N/A #8-32 by 5/8 Lg. BHCS 1**27 N/A N/A #8-32 by 1/2 Lg. SHCS 3**28 N/A N/A #10-32 by 1.0 Lg. SHCS 1**29 N/A N/A 1/8 Dia. by 1/8 Lg. Tubular Rivet 1**11-40-3096 K8301AX Tool Kit (All Y Items) REF ** The following purchased parts are available from an Industrial supply company such as MSC (1-800-645-7270).NOTES1. Molex recommends an extra perishable tooling kit be maintained at your facility.2. Verify tooling alignment by manually cycling the press before crimping under power. Check that all screws are tight.3. Slugs, terminals, dirt, and oil should be kept clear of work area.4. This Terminator should only be used in a Molex TM42, TM40, or 3BF Press with a Base Unit adaptor.5. Wear safety glasses at all times.6. For recommended maintenance refer to the TM40, TM42 Manual.CAUTION: To prevent injury never operate this Terminator without the guards supplied with the press in place. Reference the TM42 press instruction manual.CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.Molex Application Tooling Group1150 E. Diehl RoadNaperville, IL 60563Tel: (630) 969-4550Fax: (630) 505-0049Visit our Web site at 。
1、花齿压铆螺母S(钢)、CLS(不锈钢)规格代码适合板厚(最小) 底孔孔径孔心板边距(最小) M2×0.40 0/ 1 /2 0.8/1.0-1.5/2.0 φ4.25 4.8M2×0.45 0 / 1 / 2 0.8/1.0-1.5/2.0 φ4.25 4.8M3×0.5 0 / 1 / 2 0.8/1.0-1.5/2.0 φ4.25 4.8M3.5×0.6 0 / 1 / 2 0.8/1.0-1.5/2.0 φ4.75 5.6M4×0.7 0 / 1 / 2 0.8/1.0-1.5/2.0 φ5.4 6.9M5×0.8 0 / 1 / 2 0.8/1.0-1.5/2.0 φ6.4 7.1M6×1.0 0 / 1 / 2 1.2/1.4/2.3 φ8.75 8.6M8×1.25 1 / 2 1.4/2.3 φ10.5 9.7M10×1.5 1 / 2 2.31/3.18 φ14.0 13.5S-M3-2 -ZC S代表铆螺母类型M3代表螺纹尺寸2代表规格ZC表面彩锌F 2、通孔压铆螺母柱SO钢、SOS (不锈钢)[SO半牙、SOO全牙]规格六角对边长度H 适合板厚(最小) 底孔孔径孔心板边距(最小) M3×0.5 4.75 1.0 φ4.2 6.03.5M3 6-6.35 1.0 φ5.4 6.8M4×0.7 7 1.2 φ6.0 8.03.5M4 φ7.2 8.0M5×0.8 8 1.2 φ7.28.0SOO-M3-12 -ZC SOO代表铆螺母类型M3代表螺纹尺寸12代表规格ZC表面彩锌3、不通孔压铆螺母柱BSO(钢)、BSOS(不锈钢)规格六角对边长度H 最小板厚底孔孔径孔中至板边距M3×0.5 4.75 1.0 φ4.2 6.03.5M3 6-6.35 1.0 φ5.4 6.8M4×0.7 7.0 1.0 φ6.0 73.5M4 8.0 1.3 φ7.2 8.0M5×0.8 8 1.3 φ7.2 8.0M6×1.0 10 1.3 φ8.75BSO-M3-12 -ZC BSO代表铆螺母类型M3代表螺纹尺寸12代表规格ZC表面彩锌4、镶入螺母F钢)、FS(不锈钢)规格代码适合板厚(最小) 底孔孔径孔心板边距(最小) M2×0.40 1/2 1.5/2.32 φ4.4 6M2×0.45 1/2 1.5/2.32 φ4.4 6M3×0.5 1/2 1.5/2.32 φ4.4 6M4×0.7 1/2 1.5/2.32 φ7.4 7.2M5×0.8 1/2 1.5/2.32 φ7.9 8M6×1.0 3/4/5 3.2/4/4.72 φ8.75 8.8F-M3-2 -ZC F代表铆螺母类型M3代表螺纹尺寸2代表规格ZC表面彩锌5、连接螺母柱DSO(钢),DSOS(不锈钢)规格代码最小板厚底孔孔径孔中至板边距M3 φ4.26、FC松不脱螺钉(涨铆)规格适合板厚底孔孔径沉孔90度沉孔后直身FC-3-1/FC-3-1B 0.8-1.5 φ4.8 φ5.6X90°0.4FC-3-2/FC-3-2B 1.5-3.0 φ4.8 φ5.6X90° 1FC-3-3/FC-3-3B 0.8-2.0 φ4.7(4.5) Φ5.6x90°0.4FC-4/FC-4B 2.0-3.5 φ6.8 φ8.8X90° 1 C-6B 3.0-4.8 φ8.2 φX90° 1.6注:FC-4/FC-4B螺钉规格为M4,FC-6B螺钉规格为M6,B表示颜色为黑色.此涨铆螺钉必须背面沉孔。
1、花齿压铆螺母S(钢)、CLS(不锈钢)规格代码适合板厚(最小) 底孔孔径孔心板边距(最小) M2×0.40 0/ 1 /2 0.8/1.0-1.5/2.0 φ4.25 4.8M2×0.45 0 / 1 / 2 0.8/1.0-1.5/2.0 φ4.25 4.8M3×0.5 0 / 1 / 2 0.8/1.0-1.5/2.0 φ4.25 4.8M3.5×0.6 0 / 1 / 2 0.8/1.0-1.5/2.0 φ4.75 5.6M4×0.7 0 / 1 / 2 0.8/1.0-1.5/2.0 φ5.4 6.9M5×0.8 0 / 1 / 2 0.8/1.0-1.5/2.0 φ6.4 7.1M6×1.0 0 / 1 / 2 1.2/1.4/2.3 φ8.75 8.6M8×1.25 1 / 2 1.4/2.3 φ10.5 9.7M10×1.5 1 / 2 2.31/3.18 φ14.0 13.5S-M3-2 -ZC S代表铆螺母类型M3代表螺纹尺寸2代表规格ZC表面彩锌F 2、通孔压铆螺母柱SO钢、SOS (不锈钢)[SO半牙、SOO全牙]规格六角对边长度H 适合板厚(最小) 底孔孔径孔心板边距(最小) M3×0.5 4.75 1.0 φ4.2 6.03.5M3 6-6.35 1.0 φ5.4 6.8M4×0.7 7 1.2 φ6.0 8.03.5M4 φ7.2 8.0M5×0.8 8 1.2 φ7.28.0SOO-M3-12 -ZC SOO代表铆螺母类型M3代表螺纹尺寸12代表规格ZC表面彩锌3、不通孔压铆螺母柱BSO(钢)、BSOS(不锈钢)规格六角对边长度H 最小板厚底孔孔径孔中至板边距M3×0.5 4.75 1.0 φ4.2 6.03.5M3 6-6.35 1.0 φ5.4 6.8M4×0.7 7.0 1.0 φ6.0 73.5M4 8.0 1.3 φ7.2 8.0M5×0.8 8 1.3 φ7.2 8.0M6×1.0 10 1.3 φ8.75BSO-M3-12 -ZC BSO代表铆螺母类型M3代表螺纹尺寸12代表规格ZC表面彩锌4、镶入螺母F钢)、FS(不锈钢)规格代码适合板厚(最小) 底孔孔径孔心板边距(最小) M2×0.40 1/2 1.5/2.32 φ4.4 6M2×0.45 1/2 1.5/2.32 φ4.4 6M3×0.5 1/2 1.5/2.32 φ4.4 6M4×0.7 1/2 1.5/2.32 φ7.4 7.2M5×0.8 1/2 1.5/2.32 φ7.9 8M6×1.0 3/4/5 3.2/4/4.72 φ8.75 8.8F-M3-2 -ZC F代表铆螺母类型M3代表螺纹尺寸2代表规格ZC表面彩锌5、连接螺母柱DSO(钢),DSOS(不锈钢)规格代码最小板厚底孔孔径孔中至板边距M3 φ4.26、FC松不脱螺钉(涨铆)规格适合板厚底孔孔径沉孔90度沉孔后直身FC-3-1/FC-3-1B 0.8-1.5 φ4.8 φ5.6X90°0.4FC-3-2/FC-3-2B 1.5-3.0 φ4.8 φ5.6X90° 1FC-3-3/FC-3-3B 0.8-2.0 φ4.7(4.5) Φ5.6x90°0.4FC-4/FC-4B 2.0-3.5 φ6.8 φ8.8X90° 1 C-6B 3.0-4.8 φ8.2 φX90° 1.6注:FC-4/FC-4B螺钉规格为M4,FC-6B螺钉规格为M6,B表示颜色为黑色.此涨铆螺钉必须背面沉孔。
端子铆压高度和拉力参照表項次端子規格刀片規格代號可使用次數線徑AWG(kg)(mm)絕緣體鉚合高度(mm)備注1 1.0端子G80K次34AWG>0.40.41±0.050.68±0.0832AWG(0.237mm)>0.40.46±0.050.80±0.130AWG(0.255mm)≧1.10.55±0.050.80±0.08發泡pe 30AWG(0.255mm)≧1.00.48±0.050.75±0.0828AWG(0.321mm)＞1.10.51±0.08 1.0±0.0828AWG(0.321mm)>1.10.55±0.050.86±0.08發泡pe7根编织打扭≧1.10.58±0.050.85±0.08地線地線+1股编织(5根導體)+熱縮管≧1.30.58±0.050.95±0.081股地線+套管>1.10.50±0.08 1.0±0.12 1.25端子H90K次32AWG(0.237mm)>0.50.53±0.050.99±0.130AWG(0.255mm)≧1.10.55±0.060.95±0.0830AWG(0.255mm)≧1.50.57±0.060.98±0.08雙芯并鉚30AWG(0.255mm)≧1.10.58±0.08 1.1±0.1JST端子28AWG(0.321mm)≧1.80.54±0.06 1.1±0.0828AWG(0.321mm)>1.10.56±0.05 1.04±0.124AWG(OD1.4mm)≧2.00.70.±0.08 1.26±0.130AWG+28AWG(OD0.4+0.6)>1.80.62.±0.08 1.23±0.1雙芯并鉚編織2股(20±2根)＋套管≧2.00.60±0.08 1.28±0.13 1.27諯子E90K次18AWG(1.024mm)≧3.5 1.30±0.1應用于GF1009類型產品4 1.5端子I100K次地线(14根)＋套管>3.00.71±0.08 1.1±0.128AWG+28AWG(OD0.9+0.6)>3.50.65.±0.08 1.23±0.1雙芯并鉚28AWG(0.321mm)>1.10.65±0.08 1.2±0.1線材OD0.9 28AWG(0.321mm)>1.10.65±0.08 1.02±0.1線材OD0.7(富強) 28AWG(0.321mm)＞1.10.64±0.08 1.02±0.1線材OD=0.6mm 26AWG(0.405)电子线≧2.50.66±0.08 1.15±0.124AWG(0.511mm)＞3.50.63±0.08 1.42±0.17根地線+1股編織(5根導体)≧2.00.63±0.08 1.15±0.085 2.0端子A110K次32AWG(0.237mm)>0.70.71±0.08 1.20±0.132AWG(0.237mm)×2>1.50.72±0.08 1.30±0.1雙芯并鉚30AWG(0.255mm)≧1.20.60±0.05 1.1±0.0830AWG(0.255mm)>0.70.58±0.08 1.10±0.128AWG(0.321mm)≧2.50.72.±0.08 1.58±0.08OD=0.6+0.9mm 28AWG(0.321MM)+1股編織(5根導体)+地線(7根導体)≧5.00.74.±0.081.60±0.08(導+0.13T熱縮管+端子T)适用于GWH1057-1類型產品28AWG(0.321mm)＞1.30.65±0.08 1.27±0.1線材OD1.2mm28AWG(0.321mm)>1.70.65±0.08 1.22±0.1苾線并地線28AWG(0.321mm)>1.30.65±0.08 1.08±0.0828AWG(0.321mm)>1.30.65±0.08 1.68±0.08線材OD1.2(燦達低腳端子) 26AWG(0.405mm)>2.50.60±0.1 1.70±0.124AWG(OD1.4mm)≧3.50.70.±0.08 1.65±0.124AWG(OD1.4mm)≧3.50.80.±0.08 1.50±0.1燦達端子24AWG(0.511mm)>2.90.70±0.08 1.25±0.1線材OD1.0 22AWG(0.644mm)>4.90.95±0.08 1.80±0.1JST端子22AWG(0.644mm)>4.90.95±0.08 1.63±0.122AWG(0.644mm)>4.90.75±0.08 1.80±0.1加煒端子7根编织打扭≧1.20.62±0.05 1.1±0.08地線編織(15±3根)1+套管>2.00.65±0.08 1.22±0.16 2.5端子B150K 28AWG(0.321mm)>1.10.71±0.08 1.38±0.128AWG(0.321mm)>1.10.71±0.08 1.6±0.1OD0.6mm 26AW(0.405mm)>1.80.75±0.08 1.73±0.122AWG(0.644mm)>4.90.88±0.08 1.82±0.1项次端子规格刀片规格代号可使用次数线径AWGkg(mm)绝缘体铆合高度(mm)备注62.5端子B150K26AW(0.405mm)×2>4.50.94±0.08 1.95±0.1雙芯并鉚24AWG(0.511mm)≧5.00.88.±0.08 1.84±0.1雙芯并鉚24AWG(0.511mm)>3.50.80±0.08 1.80±0.122AWG(0.644mm)×2>7.0 1.30±0.8 1.88±0.1雙芯并鉚22AWG(0.644mm)×2≧3.0 1.0±0.08 1.80±0.1雙芯并鉚(加成) 20AWG(0.812mm)≧5.00.98.±0.08 1.75±0.118AWG(1.024mm)>5.0 1.05±0.08 1.95±0.115±2根编织铜丝≧1.80.76±0.08 1.2±0.172.54端子c170K次32AWG(0.237mm)>0.60.65±0.08 1.34±0.1同軸線30A WG(0.255mm)＞0.70.70±0.08 1.35±0.1同軸線30AWG(銅軸線)並打>1.20.82±0.05 2.27±0.08德開端子30AWG(銅軸線)單打>1.00.80±0.05 1.65±0.0830AWG(0.255mm)>0.70.68±0.08 1.05±0.128AWG(3芯并鉚)≧5.00.82±0.081.62±0.1應用于GWH0924-1類型產品28AWG(0.321mm)≧1.10.66±0.081.05±0.1線材OD0.8mm28AWG(0.321mm)≧1.10.72±0.081.32±0.1燦達端子(od1.2mm)28AWG(0.321mm)×2>3.50.73±0.08 1.56±0.1芯線去外被穿HST.并鉚28AWG電子線.>1.20.80±0.05 1.40±0.0828AWG(0.321mm)>3.50.73±0.08 1.65±0.1雙並芯線28AWG(0.321mm)>1.10.66±0.08 1.25±0.128AWG(0.321MM)+1股編織(5根導体)+地線(7根導体)≧5.00.78.±0.081.48±0.1(導+0.13T熱縮管+端子T)适用于GWH1057-1類型產品28AWG(0.321MM)+地線(7根導体)≧3.00.76.±0.08 1.15±0.128AWG(0.321mm)≧2.00.73±0.081.45±0.08線材OD1.55mm 26AWG(0.405)×2≧4.50.95±0.08 1.82±0.1雙芯并鉚26AWG(0.405)×2≧4.50.95±0.08 1.65±0.1MOLEX2.54諯子并打26AWG(0.405)≧3.50.90±0.08 1.52±0.1燦達端子26AW(0.405mm)×3>6.0 1.02±0.08 1.84±0.1三芯并鉚26AWG(0.405mm)>1.80.75±0.08 1.58±0.1線材OD1.324AWG(0.511)+7根铜絲(0.376mm)≧3.50.85±0.08 1.65±0.08 24AWG(OD1.4mm)≧5.70.74±0.08 2.0±0.0824AWG(0.511mm)>2.90.78±0.1 1.40±0.122AWG(0.644mm)>4.90.88±0.1 1.62±0.120AWG(0.812mm)﹥5 1.02.±0.08 1.85±0.1地線3股>30.90±0.05 1.70±0.08地線2股並打>30.85±0.08 1.80±0.14股編織(每股10根)+熱縮管﹥3.50.85.±0.08 1.38±0.1兩股編織+地線+熱縮管≧2.00.84±0.081.35±0.1燦達端子8 3.0端子DP1200K次22AWG(0.644mm)>7.0 1.86±0.1 3.07±0.13根線並打22AWG(0.644mm)>8.0 1.88±0.1 3.08±0.14根線並打20AWG(0.812mm)>7.0 1.1±0.08 1.85±0.193.0“ｏ＂型端子J200K次24AWG(0.511mm)>2.20.75±0.13根芯線並打，不需打絕緣體24AWG(0.511mm)>2.00.7±0.12根芯線並打，不需打絕緣體24AWG(0.511mm)>1.80.65±0.1單根打端,不需打絕緣體项次端子规格刀片规格代号可使用次数线径AWG標準拉(kg)导体铆合高度(mm)绝缘体铆合高度(mm)备注10 3.2端子Y200K次20AWG(0.812mm)>7.7 2.40±0.14根芯線並打，不需打絕緣體18AWG(1.024mm)>10 1.80±0.13根芯線並打，不需打絕緣體11 3.5端子L170K 24AWG(0.511)+7根铜絲(0.376mm)>3.00.82±0.05 1.72±0.08燦達端子24AWG(0.511)+7根铜絲(0.376mm)>3.00.82±0.05 1.72±0.08燦達端子24AWG(0.511)+7根铜絲(0.376mm)>3.00.82±0.05 1.72±0.08燦達端子12 3.96端子D200K次20AWG(0.812mm)﹥5 1.20.±0.08 2.4±0.1燦達端子13 5.08端子E200K次22AWG+26AWG>7.0 1.42±0.1 2.50±0.122AWG+26AWG+26AWG>7.5 1.52±0.1 3.05±0.122AWG>6.0 1.13±0.1 2.05±0.122AWG(OD2.1mm)>10 1.75±0.08 3.15±0.118AWG(OD2.1mm)>10 1.4±0.08 2.4±0.118AWG(1.024mm)備注欄 1.25±0.1 2.20±0.1>7.5<10kg 22AWG(0.644mm)>6.0 1.13±0.1 2.05±0.114SATA15PIN端子F200K次20AWG(OD1.8mm)≧3.6 1.35±0.0.08 1.27端子18AWG(OD1.8mm)≧10 1.40±0.08 2.4±0.1SATA7+6PIN端子F200K次26AWG(0.405)电子线≧2.50.64±0.06按鍍錫后再鉚壓量測SATA7+15PIN端子F200K次18AWG(1.024mm)電子線﹥6.0 1.40±0.0815S-ATA端子F200K次30AWG(0.255mm)>1.00.62±0.03宏技新CONNECTOR30AWG(0.255mm)>1.00.69±0.03上端CONNECTOR30AWG(0.255mm)>1.20.80±0.03(双苾并打)28AWG(0.321mm)>1.80.74±0.0528AWG(0.321mm)>1.80.85±0.06(双苾并打)26AWG(0.405mm)>2.00.78±0.0522AWG電子線>3.6 1.16±0.130AWG(0.255mm)≧1.00.56﹢0﹣0.04第1.7PIN單芯(創意新)新刀模30AWG(0.255mm)>1.20.70﹢0﹣0.05第4芯線雙芯並打鉚高(創意新)新刀模30AWG(0.255mm)≧1.00.60﹢0﹣0.05第 2.3.5.6PIN單芯(創意新)新刀模28AWG(0.321mm)>1.80.60±0.04第四芯線並打鉚高0.75±0.08 26AWG(0.405mm)>2.00.70±0.0816HDMI端子HDMI500K次30AWG(0.255mm)>0.70.60±0.06鉚高為芯線鍍錫后高度备注:刀模编号为:刀模编号+端子供应商编号加成:刀模编号+JA加纬:刀模编号+JW灿达:刀模编号+CD维林:刀模编号+WL升呜:刀模编号+SM富强:刀模编号+FQ朝贵:刀模编号+CG 如：加成2.0端子:AJA核準:審核制表:。
