DCK-3900说明书

3900型接收机技术说明3900型主板为数码芯片及单片机进行工作。

设备为免调试型。

操作简单，抗干扰能力远远优于模拟线路主板。

1、用DS1、DS2、DS3三个贴片指示灯来反映环境干扰情况；在现场，当DS1微微闪烁，DS2、DS3不亮时，表示环境有一定干扰，设备可正常使用，但检测率最高可下降30%；若DS1一直亮，则不管DS2、DS3为何种状态，皆表明安装地点干扰严重，需确定干扰源并排除，或采取改变安装方案、地点等方式解决。

2、顺时针调整VR4、可提高检测灵敏度，此时DS1、DS2、DS3绿色发光二极管可能会闪烁；静态调整时，以满足现场标签检测灵敏度，且DS1、DS2、DS3绿色发光二极管均不闪烁（亮）为最佳状态。

3、调制频率自适应发射板调制频率改变时（错频）3900型接收机不需要调整。

4、声，光报警设置JP2设置为1&2时（出厂状态），声光报警同步发生，持续2秒。

JP2设置为2&3时，声光报警同步发生，持续2秒，随后声音停止，报警灯仍持续闪亮3秒。

5、安装距离与标签配置安装距离1米至1.2米，软硬标签可同时使用；JP1设置1&2连接。

安装距离大于1.2米小于1.8米时，建议只使用硬标签；JP1设置2&36、主要参数：输入直流电压……………………24±VDC警戒状态…………………………250mA报警状态…………………………＜300mA保险…………………250V，1A（延迟式）检测标签速度………………大于2米／秒7、主要测试点A. TP1点一射频（RF）接收幅度安装距离＜1.2米时，JP1设置1&2（自动状态），TP1点射频接收幅度为500±50mVp—p.安装距离＞1.2米＜1.6米时，JP1设置2&3连接（手动状态），TP1点射频接收幅度为300±50mV p—p；可通过调节VR2满足安装需求。

B.TP4点----静态噪声（A）幅度为400±50mVp—p；调节VR4满足需求。

S-59U 152 mm (6") Circular Chart U Advanced Microprocessor Design for Reliable O perationU B acklit LCD Alphanumeric DisplayU A ll Functions Selectable from the Front Panel U Battery Backup for Operation During Power Failure U A larm for Over and Under Temperature or HumidityU S electable Alarm Delay U A udible and Visual Alarm Indication U P robe is Field Replaceable and Calibrated with No Special Equipment U C hart Number Displayed When Time and Temperature Ranges Are Selected U Selectable Single or Continuous Chart Rotation U R emote Sensor U Temperature/Humidity or Dewpoint/Humidity RecordingCircular Chart Recorders Temperature, Humidity, Dewpoint Recorders U L ow Battery Warning on Display U F old Away Carrying Handle U S nap-on Extra Support LegsCTH89. CTH89-RP replacement probe available.Probe included.S-60Specifications With Combined 18 Speed and Temperature Ranges and 4.5 m (15') Remote Probe, 115 Vac with 48-Hour Battery Back-UpPrimary Power: 115 Vac, 50/60 Hz, 3.5 W max (220 to 240 Vac, 50/60 Hz optional)Backup Power: 8 “AA” alkalinebatteries (included) for 48 hours continuous operationTemperature Accuracy: ±1°C (±2°F)Relative Humidity Range:0 to 100% (non-condensing)Relative Humidity Accuracy: ±3%Dewpoint Range: 0 to 50°C(32 to 120°F)Dewpoint Accuracy: ±1°C (±2°F)Probe: Combined temperature/humiditywith 4.5 m (15') cable Chart: 152 mm (6") circular chart(supplied with 60 assorted charts)Chart Rotation Speeds:User selectable: 7-day, 24-hr, 12-hr, 6-hr, 3-hr, and 1.5-hrChart Rotation: User selectablecontinuous or single turn Chart Speed Accuracy: Better than 1%Display: Alphanumeric backlit LCD,16 characters x 2 lines Temperature Alarm Range:-30 to 50°C (-20 to 120°F)Relative Humidity Alarm Range:0 to 100% RH Alarm Delay Range: User selectable,no delay, 10-min, 30-min, 1-hr, and 2-hrsRemote Alarm Connection:Normally open contacts 48 Vac/Vdc, 0.1 A resistive loadMounting: Vertical or horizontalfree standing or wall mount Dimensions:23.5 H x 18.4 W x 7.0 cm D (91⁄4 x 71⁄4 x 23⁄4")Operating Ambient Temp. Range:0 to 49°C (32 to 120°F)Weight: 20.1 kg (4 lb, 7 oz)cable, 8 “AA” batteries, AC adaptor, and operator’s manual.Recording charts (use 12 hour chart for 1.5-3 and 6 hour speeds).Ordering Examples: CTH89 and CTH89C-E20120F12, circular chart replacement chart, 12 hour record time, -20 to 120°F range, box of 60.OCW-3, OMEGACARE SM extends standard 1-year warranty to a total of 4 year.D o n ’t F o r g e t t h e A c c e s s o r i e s! P l e a s e R e f e r t o t h e O r d e r i n g T a b l e f o r a C o m p l e t e S e l e c t i o n o f C h a r t s a n d R e p l a c e m e n t P e n s .OMEGACARE SMextended warranty programis available for models shown on this page.Ask your sales representative for full details when placing an order. OMEGACARE SMcovers parts, labor and equivalent loaners. Insert range code from chart below.。

F ortiGate 3900E SeriesFG-3980E/-DC and FG-3960E/-DCHigh Performance with FlexibilityThe FortiGate 3900E Series enables organizations to build security-driven networks that can weave security deep into their datacenter and across their hybrid IT architecture to protect any edge at any scale.Powered by a rich set of AI/ML-based FortiGuard Services and an integrated security fabric platform, the FortiGate 3900E Series delivers coordinated, automated, end-to-end threat protection across all use cases.The industry’s first integrated Zero Trust Network Access (ZTNA) enforcement within an NGFW solution, FortiGate 3900E Series automatically controls, verifies, and facilitates user access to applications delivering consistent convergence with a seamless user experience.HighlightsGartner Magic QuadrantLeader for both Network Firewalls and SD-WAN.Security-Driven Networking FortiOS delivers convergednetworking and security.Unparalleled Performance with Fortinet’s patented / SPU / vSPU processors.Enterprise Security with consolidated AI / ML-powered FortiGuard Services.Hyperscale Security to secure any edge at any scale.Feature FG-3980E/-DC FG-3960E/-DC FIREWALL 1.05 Tbps 620 Gbps IPS 32 Gbps 30 Gbps NGFW28 Gbps 22 Gbps THREAT PROTECTION 20 Gbps13.5 GbpsNETWORK INTERFACESMultiple 40/100 GE QSFP+/QSFP28, 1/10 GE SFP/SFP+ slots and GE RJ45Multiple 40/100 GE QSFP+/QSFP28, 1/10 GE SFP/SFP+ slots and GE RJ45Data SheetFortiOS EverywhereFortiOS, Fortinet’s Advanced Operating SystemFortiOS enables the convergence of high performing networking and security across the Fortinet Security Fabric. Because it can be deployed anywhere, it delivers consistent and context-aware security posture across network, endpoint, and multi-cloud environments. FortiOS powers all FortiGate deployments whether a physical or virtual device, as a container, or as a cloud service. This universal deployment model enables the consolidation of many technologies and use cases into a simplified, single policy and management framework. Its organically built best-of-breed capabilities, unified operating system, and ultra-scalability allows organizations to protect all edges, simplify operations, and run their business without compromising performance or protection.FortiOS dramatically expands the Fortinet Security Fabric’s ability to deliver advanced AI/ML-powered services, inline advanced sandbox detection, integrated ZTNA enforcement, and more, provides protection across hybrid deployment models for hardware, software, and Software-as-a-Service with SASE.FortiOS expands visibility and control, ensures the consistent deployment and enforcement of security policies, and enables centralized management across large-scale networks with the following key attributes:•Interactive drill-down and topology viewers that display real-time status•On-click remediation that provides accurate and quick protection against threats and abuses •Unique threat score system correlates weighted threats with users to prioritize investigationsFortiConverter ServiceFortiConverter Service provides hassle-free migration to help organizations transition from a wide range of legacy firewalls to FortiGate Next-Generation Firewalls quickly and easily. The service eliminates errors and redundancy by employing best practices with advanced methodologies and automated processes. Organizations can accelerate their network protection with the latest FortiOS technology.Intuitive easy to use view into the network andendpoint vulnerabilitiesVisibility with FOS Application SignaturesAvailable inCloudHostedVirtualApplianceContainerFortiGuard ServicesNetwork and File SecurityServices provide protection against network-based and file-based threats. This consists of Intrusion Prevention (IPS) which uses AI/M models to perform deep packet/SSL inspectionto detect and stop malicious content, and apply virtual patching when a new vulnerability is discovered. It also includes Anti-Malware for defense against known and unknown file-based threats. Anti-malware services span both antivirus and file sandboxing to provide multi-layered protection and are enhanced in real-time with threat intelligence from FortiGuard Labs. Application Control enhances security compliance and offers real-time application visibility. Web / DNS SecurityServices provide protection against web-based threats including DNS-based threats, malicious URLs (including even in emails), and botnet/command and control communications. DNS filtering provides full visibility into DNS traffic while blocking high-risk domains, and protects against DNS tunneling, DNS infiltration, C2 server ID and Domain Generation Algorithms (DGA). URL filtering leverages a database of 300M+ URLs to identify and block links to malicious sites and payloads. IP Reputation and anti-botnet services prevent botnet communications, and block DDoS attacks from known sources.SaaS and Data SecurityServices address numerous security use cases across application usage as well as overall data security. This consists of Data Leak Prevention (DLP) which ensures data visibility, management and protection (including blocking exfiltration) across networks, clouds, and users, while simplifying compliance and privacy implementations. Separately, our Inline Cloud Access Security Broker (CASB) service protects data in motion, at rest, and in the cloud.The service enforces major compliance standards and manages account, user and cloud application usage. Services also include capabilities designed to continually assess your infrastructure, validate that configurations are working effectively and secure, and generate awareness of risks and vulnerabilities that could impact business operations. This includes coverage across IoT devices for both IoT detection and IoT vulnerability correlation.Zero-Day Threat PreventionZero-day threat prevention entails Fortinet’s AI-based inline malware prevention, our most advanced sandbox service, to analyze and block unknown files in real-time, offering sub-second protection against zero-day and sophisticated threats across all NGFWs. The service also has a built-in MITRE ATT&CK® matrix to accelerate investigations. The service focuses on comprehensive defense by blocking unknown threats while streamlining incident response efforts and reducing security overhead.OT SecurityThe service provides OT detection, OT vulnerability correlation, virtual patching, OT signatures, and industry-specific protocol decoders for overall robust defense of OT environments and devices.Secure Any Edge at Any ScalePowered by Security Processing Unit (SPU)Traditional firewalls cannot protect against today’s content- and connection-based threats because they rely on off-the-shelf hardware and general-purpose CPUs, causing a dangerous performance gap. Fortinet’s custom SPU processors deliver the power you need—up to520Gbps—to detect emerging threats and block malicious content while ensuring your network security solution does not become a performance bottleneck.ASIC AdvantageFortiCare ServicesFortinet is dedicated to helping our customers succeed, and every year FortiCare Services help thousands of organizations get the most from our Fortinet Security Fabric solution. Our lifecycle portfolio offers Design, Deploy, Operate, Optimize, and Evolve services. Operateservices offer device-level FortiCare Elite service with enhanced SLAs to meet our customer’s operational and availability needs. In addition, our customized account-level services provide rapid incident resolution and offer proactive care to maximize the security and performance of Fortinet deployments.Network Processor 6 NP6Fortinet’s new, breakthrough SPU NP6network processor works inline with FortiOS functions delivering:•Superior firewall performance for IPv4/IPv6, SCTP and multicast traffic with ultra-low latency•VPN, CAPWAP and IP tunnel acceleration •Anomaly-based intrusion prevention, checksum offload, and packet defragmentation•Traffic shaping and priority queuingContent Processor 9 CP9Content Processors act as co-processors to offload resource-intensive processing of security functions. The ninth generation of the Fortinet Content Processor, the CP9, accelerates resource-intensive SSL (including TLS 1.3) decryption and security functions while delivering:•Pattern matching acceleration and fast inspection of real-time traffic for application identification•IPS pre-scan/pre-match, signature correlation offload, and accelerated antivirus processingUse CasesNext Generation Firewall (NGFW)•FortiGuard Labs’ suite of AI-powered Security Services—natively integrated with your NGFW—secures web, content, and devices and protects networks from ransomware and sophisticated cyberattacks•Real-time SSL inspection (including TLS 1.3) provides full visibility into users, devices, and applications across the attack surface•Fortinet’s patented SPU (Security Processing Unit) technology provides industry-leading high-performance protectionSegmentation•Dynamic segmentation adapts to any network topology to deliver true end-to-end security—from the branch to the datacenter and across multi-cloud environments •Ultra-scalable, low latency, VXLAN segmentation bridges physical and virtual domains with Layer 4 firewall rules•Prevents lateral movement across the network with advanced, coordinated protection from FortiGuard Security Services detects and prevents known, zero-day, and unknown attacksSecure SD-WAN•FortiGate WAN Edge powered by one OS and unified security and management framework and systems transforms and secures WANs•Delivers superior quality of experience and effective security posture for work-from-any where models, SD-Branch, and cloud-first WAN use cases•Achieve operational efficiencies at any scale through automation, deep analytics, and self-healingMobile Security for 4G, 5G, and IoT•SPU-accelerated, high performance CGNAT and IPv6 migration options, including: NAT44, NAT444, NAT64/ DNS64, NAT46 for 4G Gi/sGi, and 5G N6 connectivity and security •RAN Access Security with highly scalable and highest-performing IPsec aggregation and control Security Gateway (SecGW)•User plane security enabled by full threat protection and visibility into GTP-U inspection Datacenter Deployment (NGFW, IPS, Segmentation)InternetFortiClientZTNA / VPNFortiGate NGFWFortiGateIPSFortiManager NOC OperationsFortiAnalyzer SOC OperationsData CenterHardwareFortiGate 3980E/-DCFortiGate 3960E/-DCInterfaces1. 1 x Console Port2. 1 x USB Port3. 2 x GE RJ45 Management Ports4. 16 x 1/10 GE SFP/SFP+ Slots5. 10 x 40/100 GE QSFP+/QSFP28 Slots Hardware FeaturesInterfaces1. 1 x Console Port2. 1 x USB Port3. 2 x GE RJ45 Management Ports4. 16 x 1/10 GE SFP/SFP+ Slots5. 6 x 40/100 GE QSFP+/QSFP28 Slots Hardware Features100 GE Connectivity for NetworkHigh-speed connectivity is essential for network security segmentation at the core of data networks. The FortiGate 3900E Series provides multiple 100 GE QSFP28 slots, simplifying network designs without relying on additional devices to bridgedesired connectivity.Note: All performance values are “up to” and vary depending on system configuration.1IPsec VPN performance test uses AES256-SHA256.2 IPS (Enterprise Mix), Application Control, NGFW and Threat Protection are measured with Logging enabled.3 SSL Inspection performance values use an average of HTTPS sessions of different cipher suites.4 NGFW performance is measured with Firewall, IPS and Application Control enabled. 5Threat Protection performance is measured with Firewall, IPS, Application Control andMalware Protection enabled.Specifications(1518 / 512 / 64 byte, UDP)/ 680 Gbps370 Gbps Firewall Latency (64 byte, UDP) 4.00 μsFirewall Throughput (Packet per Second)1020 Mpps555 Mpps Concurrent Sessions (TCP)160 MillionNew Sessions/Second (TCP)800 000720 000 Firewall Policies200 000IPsec VPN Throughput (512 byte) 1400 Gbps280 Gbps Gateway-to-Gateway IPsec VPN Tunnels 40 000Client-to-Gateway IPsec VPN Tunnels200 000SSL-VPN Throughput9.5 Gbps9 Gbps Concurrent SSL-VPN Users(Recommended Maximum, Tunnel Mode)30 000SSL Inspection Throughput(IPS, avg. HTTPS) 326 Gbps23 Gbps SSL Inspection CPS (IPS, avg. HTTPS) 317 00014 000SSL Inspection Concurrent Session(IPS, avg. HTTPS) 312 MillionApplication Control Throughput(HTTP 64K) 255 Gbps40 GBPS CAPWAP Throughput (HTTP 64K)14 Gbps13.5 Gbps Virtual Domains (Default / Maximum)10 / 500Maximum Number of FortiSwitchesSupported300Maximum Number of FortiAPs(Total / Tunnel)8192 / 4096 Maximum Number of FortiTokens20 000High Availability ConfigurationsActive-Active, Active-Passive, Clustering Storage Temperature-31°–158°F (-35°–70°C) Humidity10%–90% non-condensing Noise Level63 dBAForced Airflow Front to Back Operating Altitude Up to 7400 ft (2250 m) Compliance FCC Part 15 Class A, RCM, VCCI, CE, UL/cUL, CB Certifications USGv6/IPv6Ordering Information1 GE SFP RJ45 Transceiver Module FN-TRAN-GC 1 GE SFP RJ45 transceiver module for all systems with SFP and SFP/SFP+slots.1 GE SFP SX Transceiver Module FN-TRAN-SX 1 GE SFP SX transceiver module for all systems with SFP and SFP/SFP+ slots.10 GE SFP+ RJ45 Transceiver Module FN-TRAN-SFP+GC10 GE SFP+ RJ45 transceiver module for systems with SFP+ slots.10 GE SFP+ Transceiver Module, Short Range FN-TRAN-SFP+SR10 GE SFP+ transceiver module, short range for all systems with SFP+ and SFP/SFP+ slots.10 GE SFP+ Transceiver Module, Long Range FN-TRAN-SFP+LR10 GE SFP+ transceiver module, long range for all systems with SFP+ and SFP/SFP+ slots.10 GE SFP+ Transceiver Module, Extended Range FN-TRAN-SFP+ER10 GE SFP+ transceiver module, extended range for all systems with SFP+ and SFP/SFP+ slots.40 GE QSFP+ Transceiver Module, Short Range FN-TRAN-QSFP+SR40 GE QSFP+ transceiver module, short range for all systems with QSFP+ slots.40 GE QSFP+ Transceiver Module, Long Range FN-TRAN-QSFP+LR40 GE QSFP+ transceiver module, long range for all systems with QSFP+ slots.100 GE QSFP28 Transceivers, Short Range FN-TRAN-QSFP28-SR100 GE QSFP28 transceivers, 4 channel parallel fiber, short range for all systems with QSFP28slots..100 GE QSFP28 Transceivers, Long Range FN-TRAN-QSFP28-LR100 GE QSFP28 transceivers, 4 channel parallel fiber, long range for all systems with QSFP28slots.100 GE QSFP28 Transceivers, CWDM4FN-TRAN-QSFP28-CWDM4100 GE QSFP28 transceivers, LC connectors, 2KM for all systems with QSFP28 slots.AC Power Supply FG-7040E-PS-AC1500 W AC power supply module for FG-7030E, FG-7040E, FG-6300/6301F, FG-6500/6501F,FG-3960E, FG-3980E (not compatible for use with FG-7060E).SubscriptionsFortiGuard BundlesFortiGuard Labs delivers a number of security intelligence services to augment the FortiGate firewall platform. You can easily optimize the protection capabilities of your FortiGate with one of these FortiGuard Bundles.FortiCare EliteFortiCare Elite offers enhanced SLAs and quick issue resolution through a dedicated support team. It provides single-touch ticket handling, extended Extended End-of-Engineering-Support for 18 months, and access to the new FortiCare Elite Portal for a unified view of device and security health.Service Category Service Offering A-la-carteBundlesEnterprise ProtectionUnified Threat ProtectionAdvanced ThreatProtectionFortiGuard Security ServicesIPS Service••••Anti-Malware Protection (AMP) — Antivirus, Mobile Malware, Botnet, CDR, Virus Outbreak Protection and FortiSandbox Cloud Service ••••URL, DNS & Video Filtering Service •••Anti-Spam••AI-based Inline Malware Prevention Service ••Data Loss Prevention Service 1••OT Security Service (OT Detection, OT Vulnerability correlation, Virtual Patching, OT Signature / Protocol Decoders) 1•Application Control included with FortiCare Subscription CASB SaaS Controlincluded with FortiCare SubscriptionSD-WAN and SASE ServicesSD-WAN Underlay Bandwidth and Quality Monitoring Service •SD-WAN Overlay-as-a-Service for SaaS-based overlay network provisioning•SD-WAN Connector for FortiSASE Secure Private Access•FortiSASE subscription including cloud management and 10Mbps bandwidth license 2•NOC and SOC ServicesFortiGuard Attack Surface Security Service (IoT Detection, IoT Vulnerability Correlation, and Security Rating Updates) 1••FortiConverter Service ••Managed FortiGate Service•FortiGate Cloud (SMB Logging + Cloud Management) •FortiAnalyzer Cloud•FortiAnalyzer Cloud with SOCaaS •FortiGuard SOCaaS•Hardware and Software SupportFortiCare Essentials •FortiCare Premium ••••FortiCare Elite•Base ServicesInternet Service (SaaS) DB Updates included with FortiCare SubscriptionGeoIP DB UpdatesDevice/OS Detection Signatures Trusted Certificate DB Updates DDNS (v4/v6) Service1. Full features available when running FortiOS 7.4.12. Desktop Models onlyFortinet CSR PolicyFortinet is committed to driving progress and sustainability for all through cybersecurity,with respect for human rights and ethical business practices, making possible a digitalworld you can always trust. You represent and warrant to Fortinet that you will notuse Fortinet’s products and services to engage in, or support in any way, violationsor abuses of human rights, including those involving illegal censorship, surveillance,detention, or excessive use of force. Users of Fortinet products are required to complywith the Fortinet EULA and report any suspected violations of the EULA via theprocedures outlined in the Fortinet Whistleblower Policy. Copyright © 2023 Fortinet, Inc. All rights reserved. Fortinet, FortiGate, FortiCare and FortiGuard, and certain other marks are registered trademarks of Fortinet, Inc., and other Fortinet names herein may also be registered and/or common law trademarks of Fortinet. All other product or company names may be trademarks of their respective owners. Performance and other metrics contained herein were attained in internal lab tests under ideal conditions, and actual performance and other results may vary. Network variables, different network environments and other conditions may affect performance results. Nothing herein represents any binding commitment by Fortinet, and Fortinet disclaims all warranties, whether express or implied, except to the extent Fortinet enters a binding written contract, signed by Fortinet’s General Counsel, with a purchaser that expressly warrants that the identified product will perform according to certain expressly-identified performance metrics and, in such event, only the specific performance metrics expressly identified in such binding written contract shall be binding on Fortinet. For absolute clarity, any such warranty will be limited to performance in the same ideal conditions as in Fortinet’s internal lab tests. Fortinet disclaims in full any covenants, representations, and guarantees pursuant hereto, whether express or implied. Fortinet reserves the right to change, modify, transfer, or otherwise revise this publication without notice, and the most current version of the publication shall be applicable.October 20, 2023FG-3900E-DAT-R33-20231020。

5参数与其它说明4.2功能说明4.1功能说明3打开设备2电池安装1包装物品请勿将电池随意丢弃或抛入火中；将旧废电池放入回收箱！如内容不符，请退回经销商！On Off3USB2On Off1On Off接收器仓接收器隐身功能您的鼠标底部电池仓内自带Nano 接收器收纳仓,当您关机不用鼠标，可以将Nano 接收器收纳,不占空间,不会丢失，便于携带。

On Off电源开关开/关机功能您的鼠标底部带有一个开关，在您长时间不用鼠标时,您可以将鼠标关机，最大限度的保存电池电量。

⊙鼠标每次开机时，低电压报警灯会短暂闪烁，提示您鼠标进入工作状态。

低电压报警灯低电压报警功能电池电量低的时候，位于鼠标左顶部的低电压报警灯在您移动鼠标的时候会不停的闪烁，提醒您更换碱性电池，警告电池继续用约一周就不能工作。

dpi 切换按键光标速度切换功能您的鼠标提供了800/1600dpi 两档速度供您选择，初始设定值是1600dpi ，您可以通过位于鼠标顶部的"dpi"切换按键来获得您所需要的光标速度。

后退按键前进按键侧键功能鼠标侧面的前进、后退按键为您轻松实现了上一窗口和下一窗口的前进、后退功能，节省了更多宝贵的时间；当然您也可以在雷柏官方网站下载驱动，自定义按键功能。

5D 滚轮滚轮功能滚动上下页面将文档不可视的内容显示在当前屏中;在某些应用软件中滚轮中键可实现屏移功能和左右摇摆翻页，使您在阅读中随心自如。

技术规格无线载波频率 2402MHz-2480MHz 无线工作频道 16个，自动跳频鼠标额定电流电压 15mA@1.5V, AA×1最高追踪速度 30英寸/秒最大加速度 8G 鼠标寻迹系统 激光分辨率 800/1600dpi 可调操作距离 10m, 360°接口类型 USB1.1尺寸 104.5×72.5×39.3mm 系统要求Windows 2000, Windows XP, Windows Vista ，Windows7系统以上规格仅供参考，雷柏电子(深圳)有限公司可随时更改以上规格而不需事先通知。

目录前言 (2)第1节华为BTS3900的功能与特性 (2)第2节华为BTS3900机柜的硬件结构 (3)2.1 单板介绍 (6)2.2 BTS3900机柜外形 (7)2.3 BTS3900物理结构 (7)2.4 BTS3900逻辑结构 (8)2.5 BTS3900硬件结构介绍 (8)2.5.1 BBU硬件 (8)2.5.2 BBU硬件单板 (8)2.5.3 BBU硬件连线 (16)2.5.4 基站供电单元介绍 (16)2.5.5 基站环境监控单元DPMU介绍 (18)第3节华为BTS3900基站的典型配置结构 (13)3.1 MRFU模块介绍 (19)3.2 基本配置原则 (20)3.3 典型配置范例 (21)第4节华为BTS3900基站操作维护 (17)4.1 BTS3900 硬件维护项目 (22)4.1.1 电源和接地系统维护项目 (22)4.1.2 BTS3900 例行硬件维护项目 (22)4.1.3 机柜维护项目 (22)4.2 BTS3900 上电和下电 (23)4.2.1 BTS3900 上电 (23)4.2.2 BTS3900 下电 (25)4.3 更换MRFU 模块的方法 (26)4.3.1 前提条件 (26)4.3.2 背景信息 (26)4.3.3 操作步骤 (27)4.3.4 后续处理 (29)4.4 更换基站GTMU单板的方法 (29)4.4.1 前提条件 (29)4.4.2 背景信息 (30)4.4.3 操作步骤 (30)4.4.4 后续处理 (31)4.5 MRFU与GTMU载频指示灯状态 (32)4.5.1 GMTU单板指示灯说明 (32)4.5.2 MRFU指示灯说明 (33)第5节华为BTS3900基站扩减容 (26)5.1 基站扩容 (34)5.2 基站减容 (34)第6节华为BTS3900基站常见故障快速定位指导书 (26)第7节华为BTS3900基站常见故障处理 (26)7.1 OML链路故障告警（断站） (35)7.2 ALM-28011 射频单元接收通道异常告警 (36)7.3 射频单元维护链路异常告警 (36)7.4 E1/T1信号丢失告警 (37)7.5 锁相环严重告警 (38)7.6 时钟参考源异常告警（指主控板上的告警） (38)7.7 分集接收通道告警 (39)7.8 载频驻波告警 (39)7.9 GSM小区退出服务告警 (40)第8节华为BTS3900基站典型案例分析 (30)前言 BTS3900是华为公司开发的第四代室内宏基站，相对于以往传统基站，其容量更大但体积更小、性能更好且运维成本更低、集成度更高且模块更小，代表了GSM基站的未来发展方向。

JB-QG-OLK3900G 消防联动控制设备使用说明书一、特点：JB-QG(QT)-OLK3900G消防联动控制设备（以下简称控制柜）是专为消防控制系统中的重要设备：消防泵、喷淋泵、排烟机、送风机、防火卷帘门、电梯等实施可靠控制而设计的。

控制柜采用模块化组合结构，可根据工程中设备的多少灵活配置模块的数量，组成专用多线制控制柜，应用起来方便、可靠。

本控制柜由主模块，主模块显示板，启停模块，启停模块显示板组成。

本控制柜能够和OZH4800A火灾报警控制器（联动型）相通讯，启动、反馈、设备数量、安装位置在火灾报警控制器上清楚、直观的显示，同时不受火灾报警控制器的限制，可以单独对现场设备实施可靠的控制，完全符合GB16806-1997《消防联动控制设备通用技术条件》。

本控制柜可与其它厂家火灾报警系统进行联网，接收系统中的控制器、输出模块等设备的常开无源输出接点信号，实现自动启动现场联动设备。

二、主要技术指标：（1）、环境温度：-10℃～+50℃（2）、环境湿度：≤95%（40±2℃）（3）、主电源：DC24V三、各模块外形、功能及操作方法【启动】用于启动现场的喷淋泵、消防泵等重要设备，在键盘允许状态下，按下此键，可启动现场的设备，并点亮相应启动指示灯，主模块发出火警声响，OZH4800火灾报警控制器（联动型）在启动菜单中显示启动模块的地址、时间、安装位置和类型。

【停止】当现场的联动设备已处于启动状态，若现场情况有变，需紧急停止时，按下此键，现场设备运行停止，同时点亮模块上的停止指示灯。

【反馈】无源常开动作信号回答。

当主模块接收到现场设备启动后的无源反馈信号后，反馈指示灯点亮，主模块发出火警声响，OZH4800火灾报警控制器（联动型）在反馈菜单中显示启动模块的地址、时间、安装位置和类型。

【线路故障】当主模块和现场连接的设备出现短路或断线时，此指示灯点亮，同时主模块发出故障声响。

【总启动】控制柜只要有一个设备在启动，点亮此总指示灯。

HP Deskjet 3900 series用户指南惠普公司说明本文稿包含的信息如有更改，恕不另行通知。

保留所有权利。

除版权法允许之外，未经惠普公司事先书面许可，不得对本手册进行复制、改编或翻译。

HP 产品与服务的唯一担保已在这些产品与服务随附的书面担保声明中阐明。

此处的任何信息将不会构成额外担保的制定。

HP 将不会对本文包含的技术或编辑错误或者疏忽负责。

声明Apple、苹果标志、ColorSync、ColorSync 标志、Finder、Mac、Macintosh、MacOS、Powerbook、Power Macintosh 及 Quickdraw 是Apple Computer, Inc. 在美国和其他国家（地区）注册的商标。

TrueType 是 Apple Computer, Inc. 在美国的商标。

Adobe、AdobeRGB 和 Acrobat 是Adobe Systems Incorporated 的商标。

版权所有 2005 Hewlett-Packard Development Company, L.P.。

术语与约定本《用户指南》中使用下列术语与约定。

术语HP Deskjet 打印机亦指HP 打印机或打印机。

注意和警告注意标示可能会对 HP Deskjet 打印机或其他设备造成损坏。

例如：小心不要触摸打印墨盒墨水喷嘴或铜质触点。

触摸这些部件将会引起墨水阻塞、不喷墨和电路接触不良。

警告标示可能会对您自己或其他人造成的伤害。

例如：警告将新的和用过的打印墨盒放在儿童接触不到的地方。

目录1欢迎使用 (3)2特殊功能 (4)3使用入门 (5)打印机功能 (5)“电源”按钮和指示灯 (6)纸盘 (6)打印墨盒 (8)墨水备份模式 (9)4连接打印机 (10)5打印照片 (11)打印无边框照片 (11)打印带边框的照片 (13)HP Real Life 技术 (14)最大 dpi (15)存储和处理照片纸 (15)打印照片时节省金钱 (16)6打印其他文稿 (17)电子邮件 (17)信函 (18)文稿 (19)信封 (20)小册子 (20)贺卡 (21)明信片 (22)投影胶片 (23)标签 (24)索引卡和其他小介质 (25)烫印转印纸 (25)7打印提示 (27)选择打印质量 (27)设置页面顺序 (27)在单张纸上打印多个页面 (28)选择纸张类型 (28)打印预视 (28)8打印机软件 (29)打印设置 (29)管理打印机 (Mac OS X 10.3) (30)管理打印机 (Mac OS X 10.2) (31)用户指南1查看和更改打印作业的状态 (Mac OS X 10.3) (31)查看和更改打印作业的状态 (Mac OS X 10.2) (32)9维护 (33)安装打印墨盒 (33)校准打印墨盒 (36)自动清洗打印墨盒 (36)打印测试页 (36)查看估计墨水量 (36)维护打印机机身 (37)去除皮肤和衣物上的墨水 (37)手动清洗打印墨盒 (37)维护打印墨盒 (39)HP 打印机实用程序 (39)10疑难解答 (41)打印机不打印 (41)卡纸 (42)纸张问题 (43)打印机停止运作 (44)打印墨盒问题 (44)照片未正确打印 (46)打印质量不佳 (46)文稿打印错误 (47)无边框文稿相关问题 (48)错误信息 (50)“电源”指示灯闪烁 (52)文稿打印缓慢 (52)如果问题仍然存在 (53)11耗材 (54)纸张 (54)USB 电缆 (54)12规格 (55)打印机规格 (55)13环保信息 (56)环保声明 (56)打印墨盒回收利用 (57)索引 (58)2HP Deskjet 3900 series1欢迎使用要查找问题的答案，请选择以下的其中一个主题：●特殊功能●使用入门●连接打印机●打印照片●打印其他文稿●打印提示●打印机软件●维护●疑难解答●耗材●规格●环保信息用户指南32特殊功能祝贺您！您购买的 HP Deskjet 打印机配备数种特殊功能：●易于使用：易于安装和操作。

DCK-4230/4231/4232/4332电导率仪使用说明、使用前注意事项:1、安装、使用前请详细阅读本说明书相关章节，防止错误操作，造成测量误差或仪表损坏。

2、不恰当的安装和不合适的流速会使测量出现很大偏差，请详细了解安装章节。

3、此仪表属于精密电化学仪表，应由了解和掌握该专业知识的人员负责安装、操作、保修条款：1、自购买之日起，产品质量保证期为一年。

在质量保证期内，产品出现质量问题, 公司负责免费维修或更换产品。

2、公司对售出产品提供终身维护服务。

3、对下列原因造成产品的损坏，不在保修范围之内：A、使用、维护不当造成的烧毁、浸水；B、未经许可进行的改装和误用；C、超出本公司产品规定的使用环境造成的损坏；D 因选型不当造成的附带损失；E、安装、使用不当造成的线缆断裂、损坏；F、私自拆线或接线造成传感器测量不准；G 不谨慎拆卸造成的接头内部断线。

一、产品概述：DCK-4000系列工业在线电导率仪是工业流程水质连续测量与控制的分析仪表，采用一个内藏的微型计算机芯片存储、计算、补偿和有关测定电导率值的所有计算参数，例如：溶液电导率的常数修正，温度补偿，参数之间的相互换算，各项信号输出和控制的设定。

丰富的软件功能，使的本系列仪表具有功能完善、操作方便，抗干扰性强，测量准确，运行稳定，工作可靠，标准化程度高和极少维护等特点。

广泛应用于反渗透、电渗析，海水淡化，化学制程，中水回用及各种水处理装置作水质连续监控；水冷却系统、中央空调、锅炉底水的电导率监视控制和药剂投加。

特点：1. 新一代翠绿色、大型字段式背景光液晶屏，具有多种提示符号及状态显示支持卩S/cm, ppm （TDS ,mS/cm, TEMP（温度）多功能选择显示；2. 支持多种电极常数和电极离散性校正（0.1 cm-1; 1.0cm-1; 10cm1）;3. 指定量程/自动量程双选择设定，可选的上限/下限动作模式，双路继电器构成三位控制；4. 仪表/变送器双模式传送，隔离型、可迁移4〜20mA电流环，适配所有国别、型号的PLC模块（DCK-4332型号），具有强大的兼容性。

SD拷贝机SD-3900使用说明书一、简介：欢迎使用40位高速SD卡拷贝机。

本设备主要功能如下：1.是完全独立的复制设备，不需要再外接计算机；2.具有40个卡槽，能同时复制39块SD卡；3.所有的卡均可以同/异步独立复制；4.可以根据用户实际的情况选择不同的复制方式: 完全复制、快速复制、DD镜像复制，异步复制；5.具备软件升级的功能；6.提供中英文两种语言菜单可供选择；7.独具异步复制功能，采用智能识别功能，系统插入空白的内存卡可以自动识别然后开始复制，各个设备之间互不干扰，能极大的提高系统的使用效率；二、菜单显示详解备注：在主菜单下，系统会自动检测插入的源盘和目标盘，所以主菜单右上角的两个数字会随着FLASH卡的插入而变化。

三、按键定义说明操作键部分总共有上(▲)下(▼)左(◄)右(►)四键其中上下键代表上下移动以选择执行不同的功能；左键是退出返回，相当于“ESC”；右键是确认执行，相当于“ENTER”。

四、使用简介具体介绍整盘复制、快速复制和校验的相应操作：1．整盘复制首先确定在“设置”菜单下“复制模式”里面的复制模式选项为“完全复制”，如果不是则通过按上(▲)下(▼)键选择“完全复制”选项，按右(►)键确认选择该选项，然后按左(◄)键退出到主菜单，再按上(▲)下(▼)键到“复制”菜单处，如下显示：按右(►)键开始执行复制功能，系统开始复制操作，LCD显示如下：系统显示复制过程中的所用时间、速度、复制的容量大小和复制的进度，其中容量的大小在10G之下显示为M，超过10G的时候显示的单位为G。

复制结束后，显示如下：如果复制错误，则相应的设备处的错误灯会亮起直到下一次复制开始。

2．快速复制首先确定在“设置”菜单下“复制模式”里面的复制模式选项为“快速复制”，如果不是则通过按上(▲)下(▼)键选择“快速复制”选项，按右(►)键确认选择该选项，然后按左(◄)键退出到主菜单，再按上(▲)下(▼)键到“复制”菜单处，按右(►)键开始执行复制功能，系统开始复制操作3．异步复制首先确定在“设置”菜单下“复制模式”里面的复制模式选项为“异步复制”，如果不是则通过按上(▲)下(▼)键选择“异步复制”选项，按右(►)键确认选择该选项，然后按左(◄)键退出到主菜单，再按上(▲)下(▼)键到“复制”菜单处，菜单显示如下：其中：S表示源盘，》显示相应的设备正在进行复制工作, √显示相应的设备复制结束且正确, X 显示相应的设备复制错误或设备工作出错，同时对应设备的出错灯会亮起。

Product Data Sheet00813-0100-3900, Rev ACAugust 2021 Rosemount™ 3900/3900VPGeneral Purpose pH/ORP SensorsHigh performance for your process pH/ORP needsThe Rosemount 3900 and 3900VP pH/ORP combination sensors are used for reliable pH or oxidation reduction potential measurements of aqueous solutions in pipelines, open tanks, or ponds. Their robust designs allow the Rosemount 3900 and 3900VP sensors to be used in a wide range of applications.OverviewA robust sensor design■Extended sensor life and protection against poisoning ionsusing a double junction reference.■Enhanced performance and increased life with crackingresistant glass.■Maximum chemical resistance provided by a ruggedpolyphenylene sulfide body.■Operates in sub-zero temperatures down to 14 °F (-10 °C).■Built-ins solution ground for advanced diagnostics.Versatile installation options■The sensor body features a one-piece construction with both front facing and rear facing process threads.■¾-in. and 1-in. male national pipe thread (MNPT) process connections to meet a variety of application installationrequirements.■Variopol (VP8) cable connection option, for quick cable-to-sensor release, eliminates cable twisting.SMART preamplifier■Automatic recognition of pH sensors by Rosemount transmitters: 1066, 1057, 1056, and 56.■pH calibration data is stored, which allows sensors to be calibrated in advance for "plug and play" installations in the field.Ordering informationThe Rosemount 3900 and 3900VP General Purpose pH/ORP Sensors feature a chemically resistant Ryton ® plastic body,along with a built-in solution ground for advanced diagnostics and a Pt-100 resistance temperature device (RTD) fortemperature compensation. These sensors are available with either an integral cable connection (Rosemount 3900) orVariopol (VP8) connector (Rosemount 3900VP). Variopol cables are sold separately (see Accessories ).ContentsOverview...........................................................................................................................................................................................2Ordering information........................................................................................................................................................................2Accessories........................................................................................................................................................................................5Specifications....................................................................................................................................................................................6Rosemount pH/ORP sensor(s) product certifications.........................................................................................................................7Dimensional and installation drawings.. (12)Rosemount 3900/3900VPAugust 2021/RosemountAugust 2021Rosemount 3900/3900VP Rosemount 3900 ordering informationThe Rosemount 3900 pH/ORP Sensor is housed in a Ryton® plastic body with built-in solution ground for advanced diagnostics.Pt-100 is offered for a temperature compensator. The sensor is available with an integral cable. You can mount the sensor using a process connector, both ordered separately. You can also order junction box kits with preamplifiers separately if the transmitter does not have an integral preamplifier.ModelPreamplifier options(1)Standard preamplifier if used with oxidation reduction potential (ORP).Measuring codeCalibration certificates - optional levelRosemount 3900/3900VP3Rosemount 3900/3900VP August 2021 Rosemount 3900VP ordering informationModelPreamplifier options(1)Standard preamplifier if used with oxidation reduction potential (ORP).Measuring codeCalibration certificates - optional level/RosemountAugust 2021Rosemount 3900/3900VP AccessoriesRosemount 3900/3900VP5Rosemount 3900/3900VP August 2021 SpecificationsTable 1: Percent Linearity over pH RangeTable 2: Rosemount 3900/3900VP pH/ORP Sensor Specifications/RosemountAugust 2021Rosemount 3900/3900VPRosemount pH/ORP sensor(s) product certificationsRev 0.5European directive informationA copy of the EU Declaration of Conformity can be found at the end of the Quick Start Guide. The most recent revision of the EU Declaration of Conformity can be found at /Rosemount.Ordinary location certificationAs standard, the transmitter has been examined and tested to determine that the design meets the basic electrical, mechanical, and fire protection requirements by a nationally recognized test laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA).Installing equipment in North AmericaThe US National Electrical Code® (NEC) and the Canadian Electrical Code (CEC) permit the use of Division marked equipment in Zones and Zone marked equipment in Divisions. The markings must be suitable for the area classification, gas, and temperature class. This information is clearly defined in the respective codes.USAFM Intrinsic SafetyCertificate FM17US0198XStandards FM Class 3600:1998, FM Class 3610:2010, FM Class 3611: 2004, FM Class 3810: 2005Markings IS/I,II,III/1/ABCDEFG/T6 Ta = –20 °C to 60 °CI/0/AEx ia IIC/T6 Ta = –20 °C to 60 °CNI/I/2/ABCD/T6 Ta = –20 °C to 60 °CS/II,III/2/EFG/T6 Ta = –20 °C to 60 °CSpecific Conditions for Safe Use (X):1.Sensors with Model 1700702 preamplifier:a.Model 385+-a-b-c. Triple junction pH/ORP sensorRosemount 3900/3900VP7Rosemount 3900/3900VP August 2021b.Model 389-a-b-c-d-e. pH/ORP sensorc.Model 389VP-a-b-c-d. pH/ORP sensord.Model 396VP-a-b-c-d. Submersion/insertion pH/ORP sensore.Model 396P-a-b-c-d-e. Submersion/insertion pH/ORP sensorf.Model 396PVP-a-b-c-d-e. Submersion/insertion pH/ORP sensorg.Model 396RVP-a-b-c-d-e. Retraction/submersion/insertion pH/ORP sensorh.Model 398RVP-a-b-c-d-e-f. pH/ORP sensori.Model 3200HP-00. High purity water pH sensorj.Model 3300HTVP-a-b-c-d. High performance pH and ORP sensork.Model 3400HTVP-a-b-c-d-e. High performance pH and ORP sensorl.3500P-a-b-c-d-e-f. High performance pH and ORP sensorm.3500VP-a-b-c-d-e-f. High performance pH and ORP sensorn.Model 3900-a-b-c. General purpose pH/ORP sensoro.Model 3900VP-a-b. General purpose pH/ORP sensorThe polymeric surface of all the apparatus listed above may store electrostatic charge and become a source of ignition.Clean surface should only be done with a damp cloth.2.Sensors without Model 1700702 preamplifier (simple apparatus):a.Model 385-a-b-c-d-e. Retractable pH/ORP sensorb.Model 385+-a-b-c Triple junction pH/ORP sensorc.Model 389-a-b-c-d-e. pH/ORP sensord.Model 389VP-a-b-c. pH/ORP sensore.Model 396-a-b-c. Submersion/insertion pH sensorf.Model 396VP-a-b. Submersion/insertion pH sensorg.Model 396P-a-b-c-d-e. Submersion/insertion pH/ORP sensorh.Model 396PVP-a-b-c-d. Submersion/insertion pH/ORP sensori.Model 396R-a-b-c-d-e. Retraction/submersion/insertion pH/ORP sensorj.Model 396RVP-a-b-c-d. Retraction/submersion/insertion pH/ORP sensork.Model 397-a-b-c-d-e. pH sensorl.Model 398-a-b-c-d-e. pH/ORP sensorm.Model 398VP-a-b-c. pH/ORP sensorn.Model 398R-a-b-c-d-e-f. pH/ORP sensoro.Model 398RVP-a-b-c-d-e-f. pH/ORP sensorp.Model 3200HP-00. High purity water pH sensorq.Model 3300HT-a-b-c-d. High performance pH and ORP sensorr.Model 3300HTVP-a-b-c-d. High performance pH and ORP sensors.Model 3400HT-a-b-c-d-e-f. High performance pH and ORP sensort.Model 3400HTVP-a-b-c-d-e-f. High performance pH and ORP sensoru.Model 3500P-a-b-c-d-e-f. High performance pH and ORP sensor/RosemountAugust 2021Rosemount 3900/3900VPv.Model 3500VP-a-b-c-d-e-f. High performance pH and ORP sensorw.Model 3800-a. Autoclaveable and steam sterilizable pH sensorsx.Model 3800VP-a. Autoclaveable and steam sterilizable pH sensorsy.Model 3900-a-b-c. General purpose pH/ORP sensorz.Model 3900VP-a-b. General purpose pH/ORP sensorThe polymeric surface of all the apparatus listed above may store electrostatic charge and become a source of ignition.Clean surface should only be done with a damp cloth.CSA Intrinsic SafetyCertificate70164066Standards C22.2 No 0-10, C22.2 No 0.4-M2004, C22.2 No 94-M1991, C22.2 No 142 – M1987, C22.2 No 157-M1992, CAN/CSA E60079-0:07, CAN/CSA E60079-11:02, UL 50-11th Ed, UL 508-17th Ed, UL 913-7th Ed, UL 60079-0: 2005, UL60079-11: 2002Markings Preamplifier assembly:Class I, Division 1, Groups ABCD; Class II, Division 1, Groups EFG; Class III; Class I, Division 2, Groups ABCD; ambienttemperature rating –20 °C to +60 °C; Ex ia IIC; T6: Class I, Zone 0, AEx ia IIC ; T6Sensor apparatus with preamplifier:Class I, Division 1, Groups ABCD; Class II, Division 1, Groups EFG; Class III; Class I, Division 2, Groups ABCD; ambienttemperature rating –20 °C to +60 °C; Ex ia IIC; T6: Class I, Zone 0, AEx ia IIC ; T6Sensor apparatus:Class I, Division 1, Groups ABCD; Class II, Division 1, Groups EFG; Class III; Class I, Division 2, Groups ABCD; Ex ia IIC;T6; ambient temperature rating –20 °C to +60 °C: (simple apparatus)CanadaCSA Intrinsic SafetyCertificate70164066Standards C22.2 No 0-10, C22.2 No 0.4-M2004, C22.2 No 94-M1991, C22.2 No 142 – M1987, C22.2 No 157-M1992, CAN/CSA E60079-0:07, CAN/CSA E60079-11:02, UL 50-11th Ed, UL 508-17th Ed, UL 913-7th Ed, UL 60079-0: 2005, UL60079-11: 2002Markings Preamplifier assembly:Class I, Division 1, Groups ABCD; Class II, Division 1, Groups EFG; Class III; Class I, Division 2, Groups ABCD; ambienttemperature rating –20 °C to +60 °C; Ex ia IIC; T6: Class I, Zone 0, AEx ia IIC ; T6Sensor apparatus with preamplifier:Class I, Division 1, Groups ABCD; Class II, Division 1, Groups EFG; Class III; Class I, Division 2, Groups ABCD; ambienttemperature rating –20 °C to +60 °C; Ex ia IIC; T6: Class I, Zone 0, AEx ia IIC ; T6Sensor apparatus:Class I, Division 1, Groups ABCD; Class II, Division 1, Groups EFG; Class III; Class I, Division 2, Groups ABCD; Ex ia IIC;T6; ambient temperature rating –20 °C to +60 °C: (simple apparatus)Rosemount 3900/3900VP9Rosemount 3900/3900VP August 2021 EuropeATEX Intrinsic SafetyCertificate Baseefa10ATEX0156Standards EN 60079-0: 2012+A11: 2013, EN 60079-11: 2012Markings pH/ORP sensors with no preamplifier fittedpH sensors with integral smart preamplifier fittedORP sensors with integral standard preamplifier fittedEx ia IIC T5 Ga (–20 °C to +40 °C)pH sensors with integral standard preamplifier fittedEx ia IIC T5 Ga (–20 °C to +40 °C)Specific Conditions for Safe Use (X):1.All pH/ORP sensor models with a plastic enclosure or exposed plastic parts may provide an electrostatic ignition hazard andmust only be cleaned with a damp cloth to avoid the danger of ignition due to build-up of electrostatic charge.2.All pH/ORP sensor models with a metallic enclosure may provide a risk of ignition by impact or friction. Care should be takenduring installation to protect the sensor from the risk.3.External connections to the sensor must be suitably terminated and provide a degree of protection of at least IP20.4.All pH/ORP sensor models are intended to be in contact with the process fluid and may not meet the 500V r.m.s. test toearth. This must be taken into consideration at installation.InternationalIECEx Intrinsic SafetyCertificate IECEx BAS 10.0083XStandards IEC 60079-0: 2011, IEC 60079-11: 2011Markings pH/ORP sensors with no preamplifier fittedEx ia IIC T4 Ga (–20 °C to +60 °C)pH sensors with integral smart preamplifier fittedEx ia IIC T4 Ga (–20 °C to +60 °C)ORP sensors with integral standard preamplifier fittedEx ia IIC T4 Ga (–20 °C to +80 °C)Ex ia IIC T5 Ga (–20 °C to +40 °C)pH sensors with integral standard preamplifier fittedEx ia IIC T4 Ga (–20 °C to +80 °C)Ex ia IIC T5 Ga (–20 °C to +40 °C)Specific Conditions for Safe Use (X):1.All pH/ORP sensor models with a plastic enclosure or exposed plastic parts may provide an electrostatic ignition hazard andmust only be cleaned with a damp cloth to avoid the danger of ignition due to build-up of electrostatic charge./Rosemount2.All pH/ORP sensor models with a metallic enclosure may provide a risk of ignition by impact or friction. Care should be takenduring installation to protect the sensor from the risk.3.External connections to the sensor must be suitably terminated and provide a degree of protection of at least IP20.4.All pH/ORP sensor models are intended to be in contact with the process fluid and may not meet the 500V r.m.s. test toearth. This must be taken into consideration at installation.ChinaNepsi Intrinsic SafetyCertificate GYB19.1035XStandards GB 3836.1-2010, GB 3836.4-2010, GB 3836.20-2010Markings Ex ia II C T4 Ga (–20 °C to +60 °C)Specific Conditions for Safe Use (X):1.It is strictly forbidden to rub the plastic shell parts of the product to prevent the risk of static ignition.2.When the product shell contains light metals, it should be prevented in a zone 0 environment.Technical Regulations Customs Union (EAC)EAC Intrinsic SafetyCertificate TC RU C-US .MIO62. B.06011Markings pH/ORP sensors with no preamplifier fittedEx ia IIC T4 Ga (–20 °C to +60 °C)pH sensors with integral smart preamplifier fittedEx ia IIC T4 Ga (–20 °C to +60 °C)ORP sensors with integral standard preamplifier fittedEx ia IIC T4 Ga (–20 °C to +80 °C)Ex ia IIC T5 Ga (–20 °C to +40 °C)pH sensors with integral standard preamplifier fittedEx ia IIC T4 Ga (–20 °C to +80 °C)Ex ia IIC T5 Ga (–20 °C to +40 °C)Specific Condition for Safe Use (X):See certificate for special conditions.Dimensional and installation drawings Figure 1: Proper Sensor Installation OrientationInstall sensor within 80 degrees of vertical.Figure 2: Rosemount 3900 with Integral Cable ConnectionA.1-in. male national pipe thread (MNPT)B.Wrench flats, 1.30 in. acrossC.1-in. MNPTD.¾-in. MNPTFigure 3: Rosemount 3900VP with Variopol Cable ConnectionA.Temperature compensation solution groundB.Reference junctionC.pH electrodeTable 3: Horizontal Pipe Tee (PN 2002011) Pressure/Temperature RatingsFigure 4: Typical Flow-through Insertion Installation using PN 2002011 Pipe TeeA.1½-in. x 1-in. reducing bushingB.1½-in. pipe tee PN 2002011Table 4: Low Flow Cell Specifications PN 24091-00/24091-02Figure 5: Low Flow Cell (PN 24091-00)A.IncheslimetersC.OutletD.InletFigure 6: Flow-through Tee (2-in.) (PN 914240-XX)A.AdapterThe following flow-through tees are available for the Rosemount 3900/3900VP.■915240-03■915240-04■915240-05For a new installation, use the appropriate tee above and add the S10283-LQD adapter.When replacing an existing Rosemount 399 with a Rosemount 3900 sensor, add the S10283-LQD adapter to convert the tee to accept the Rosemount 3900 sensor.Figure 7: Jet Spray CleanerA.Cleaning solution by othersB.Solenoid valve or manual valve (supplied by others)C.Corrosion resistant tubing (supplied by others)D.Polypropylene ¼-in. (6.4 mm) compression fittingE.¼-in. (6.4 mm) 316 stainless steelF.¼-in. (6.4 mm) polypropyleneG.Stainless set screw for adjustable spray nozzle heightH.2-in. (50.8 mm) NPT threadsI.SensorJ.1-in. (25.4 mm) PVC coupling for submersible applications (supplied by others) K.1-in. (25.4 mm) PVC or stainless conduit (supplied by others)L.CableM.Timer supplied by others or use timer feature in Rosemount instrument.Figure 8: Rosemount 3900 Sensor with Jet Spray CleanerThe jet spray cleaner eliminates routine, manual sensor maintenance by cleaning the sensor with water or compressed air. You can control flow through the cleaner with a solenoid valve.NoteYou can use the jet spray cleaner with the handrail mounting assembly (PN 11275-01, not shown), or you can mount it through the conduit as shown in Figure 8.Figure 9: Low Flow Panel PN 00390-7101-0001Table 5: Low Flow Panel Specifications(1)The minimum inlet pressure is required to open a check valve, which prevents the flow cell from draining if sample flow is lost. Removing thecheck valve lowers the inlet pressure requirement to a few feet of water head.August 2021Rosemount 3900/3900VP Rosemount 3900/3900VP21Rosemount 3900/3900VP August 2021 /RosemountAugust 2021Rosemount 3900/3900VP Rosemount 3900/3900VP2300813-0100-3900Rev. ACAugust 2021For more information: ©2021 Emerson. All rights reserved.Emerson Terms and Conditions of Sale are available uponrequest. The Emerson logo is a trademark and service mark ofEmerson Electric Co. Rosemount is a mark of one of theEmerson family of companies. All other marks are the propertyof their respective owners.。

Philips StreamiumWireless Hi-Fi system for Android™NP3900Stream music from PC/MAC and Internet - wirelesslyObsessed with soundEnjoy the immersive audio of LivingSound, and have it in every room with Multiroom Music. Stream PC/Mac music and Internet radio on the Philips NP3900/12 Hi-Fi system. Control what you play on its color touch screen, or via the remote App.Unlimited listening pleasure - wirelessly•Tune in and explore thousands of Internet radio stations •Wireless stream music and photos from your PC/MAC•Stream and enjoy over 10 million great songs from Napster*Easy navigation and control •View album art in full color•Full color touch screen for easy navigationReady to connect•Works with home broadband connection and Wi-Fi router •Turn your Smartphone into a remote for Philips AV products Quality sound performance•FullSound enriches your music with fuller bass and clarity •LivingSound for wider, immersive stereo sound •30W RMS total output powerHighlightsWireless stream music & photosYour PC/ MAC is filled with music that you can now conveniently stream onto your Philips audio device – without messy cables. Share your favorite songs with others at a party, or simply enjoy them at the comfort of your home. Do the same for your photo collections, and view them at leisure while you listen to music. Unlock your PC/ MAC treasures with the convenience of wireless streaming.Full color touch screenTouch screen control allows you to control your device by simply pressing on-screen buttons rather than physical buttons on the device. Simply power up the device and the touch screen user interface will show up on the LCD display with all the control options for the device. Touch screen control combines LCD display technology with pressure sensors and a powerful digital micro processor. When you press on a specific area of the screen with your finger, the relevant signal is sent to the processor and the command is immediately executed.MyRemote appThe Philips MyRemote app lets you use your iPhone, iPod Touch or Android Smartphone as a remote to control your Philips networked AV products. The app automatically recognizes your Philips Blu-ray player, Home theater or Streamium audio system connected to your home Wi-Fi network, and gives you instant control over the devices from anywhere in your home. And if you have more than one Philips networked AV product, the app will allow you to switch between them and control each one independently. This free app is created exclusively by Philips.Napster online music library*Get all the music you ever want with Napster - an online music service that offers you over 10 million tracks from 790,000 artists, 980,000 albums and all genres. Access to Napster is made effortless with the Philips micro system, thanks to the icon-based LCD display panel, and gives you all the music you want - quickly and easily. With just a few clicks, Napster's vast library is freed from your PC or MAC, and streamed wirelessly for you to enjoy on thePhilips system. Change the way you listen to music now.Internet radio stationsStreamium comes with thousands of Internet radio stations. Now you can stay abreast of all kind of music worldwide. Connect your Streamium to the Internet and listen to your favorite online programs without having to turn on your PC/MAC.FullSoundPhilips' innovative FullSound technologyfaithfully restores sonic details to compressed music, dramatically enriching and enhancing it, so you can experience music without any distortion. Based on an audio post-processing algorithm, FullSound combines Philips'renowned expertise in music reproduction with the power of the latest generation Digital Signal Processor (DSP). The result is fuller bass with more depth and impact, boosted voice and instrument clarity, and rich detail.Rediscover your compressed music in true-to-life sound that will touch your soul and moveyour feet.Issue date 2022-06-03 Version: 2.1.412 NC: 8670 000 70849 EAN: 87 12581 57858 9© 2022 Koninklijke Philips N.V.All Rights reserved.Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips N.V. or their respective owners.SpecificationsSound•Equalizer settings: Neutral•Sound Enhancement: Treble and Bass Control •Volume Control: up/down•Music Power: 30W•Type: FullSound, Living Sound Loudspeakers•Built-in speakers: 4•Loudspeaker types: IntegratedAudio Playback•Compression format: MP3, WMA, non DRM AAC (m4A), eAAC+, FLAC•Sample frequencies: 8-48 kHz (MP3)•PC Link playback mode: MP3 streaming via network, Wi-Fi wireless connection•ID3-tag support•Internet Radio•MP3 bit rates: 8-320kpbs and VBR Connectivity•Headphone: 3.5 mm•Wireless connection: Wireless LAN (802.11n), Wireless LAN(802.11g), Wireless LAN(802.11b)•Wireless Universal Plug & Play: UPnP client •LAN wired: Ethernet (RJ 45) 1x•Encryption / security: WEP 128 bit, WEP 64 bit, WPA, WPS-PBC, WPS-PIN, WPA2•Audio Connections: 3.5mm stereo line in -MP3 link •Optional iPhone dockStill Picture Playback•On-device display: Streaming from PC •Picture Compression Format: JPEG Convenience•Display Type: Touch screen LCD•On-Screen Display languages: English, Dutch,French, German, Italian, Spanish, Portuguese,Swedish, Russian•Eco Power Standby: 1 watt•Headphone jack•WiFi signal strength indicator•Clock: On main display, Internet time•Alarms: Buzzer Alarm, Sleep timer, Music Alarm(UPnP)•Display Enhancements: Brightness Control, Touchscreen control•Indications: DIM mode•Philips AV Remote App: for iPhone/AndroidsmartphoneAccessories•Included accessories: World Wide Warrantyleaflet, Quick start guide•Remote control: 1-way Remote•Batteries: 2x AAA•User Manual: English, French, German, Spanish,Italian, Dutch, Norwegian, Swedish, Finnish,Portuguese, Danish, Russian, Polish (in CD)•CD-ROM:CD-ROM with TwonkyMedia and usermanuals•Warranty Card: Warranty Card•AC/DC Adaptor: 110-240VDimensions•Product dimensions (WxDxH): 345 x 106 x 116mm•Set weight: 1.5 kg*Napster is available only in Germany and the United Kingdom.。

富莱克FLECK3900说明书,富莱克软水阀,富莱克控制阀,富莱克阀维修,富莱克阀配件,水处理配件,水处理维修目录一、产品概述二、工作流程图三、设备的系统说明四、设备的安装和运行五、设备安装示意图六、流量型控制器调试步骤七、流量型控制器组成部分八、故障排除产品概述全自动软水器采用两种再生控制系统，分为流量型和时间型。

流量型是所设定的流量控制全自动再生，流量大小可根据树脂装填量及水质情况的不同自行设定。

时间型是根据树脂装填量及水质情况结合每小时具体需求量换算时间，由设定时间控制全自动再生（7天或12天范围内根据需要设定再生周期，24小时内任意选择再生时间）。

由于全自动软水设备控制系统技术成型、操作简便、运行可靠，使之在软化水处理方面处于国际领先地位。

软水器可选微电脑控制，使其操作更加简便，管理更容易。

全自动软水器广泛应用于工业锅炉、热交换器、宾馆饭店、食品工业、洗衣印染、医疗卫生等行业，该产品具有自动化程度高、交换容量大、结构紧凑、能耗低、省人工、无需日常保养等特点，将给客户带来最佳的经济运行工况。

工作压力：0.2Mpa-0.6Mpa工作温度：2-50℃进水硬度：≤8mmol/L出水硬度：≤0.03mmol/L使用电源：220V/50HZ布置形式：单罐或多罐并联再生方式：顺流再生、可选逆流再生操作程序：自动程序控制使用树脂：强酸性阳离子交换树脂我公司将为用户提供完善的技术服务FLECK阀的特点：活塞式阀芯不但水力学性能超群，且坚固耐磨、耐腐蚀。

整套装置用一个配有定时器的多路通伺服阀集中运作，配以微电脑调控系统，安全可靠，故障率低、科学化管理程度明显提高。

微控器还具有自动调整补偿剩余水量的特定功能，使之保持运行的最佳点。

不用专设制盐系统该装置在集控阀伺中巧妙的设计了靠进水压为动力的自吸式喷射器，按工序要求定时进行吸盐和补水。

整个盐水的制备仅在交换罐近旁设一个PE材质再生箱，内置过滤搁板、净液槽并配有小巧液位控制器的再生箱即可。

The AutoTest facility in the Aeroflex IFR 3900 series testOVERVIEWC r e a t i n g a n A u t o T e s t s c r i p tA 3900 AutoTest script takes the form of a flat (unformatted) text file as created, for example, on a PC using Microsoft ®Notepad.Whichever editor you use, it is important not to apply any format-ting (such as font selection). Note that the test set requires AutoTest script files to have the extender .ats so, when saving the file in Notepad, be sure to (a) specify the extender in File name :as '.ats', and set Save as type: to 'All Files'. If you leave Save as type : at the default value of 'Text Documents (*.txt)', then the file may be saved with the extender '.ats.txt' and, in that form, will not be recognized by the test set.The file can be transferred to the test set on a USB memory stick or floppy disk, from which it can be imported via the UTILS menu (UTILS / File Management / AutoTest / Scripts / Import) (Fig 1)Fig 1: Importing an AutoTest script from floppy diskRunning a scriptTo run an AutoTest script, it is first necessary to load the 3900's AutoTest system. Press the CONFIG key twice, navigate via the ARROW keys to highlight Systems / AutoTest , and press SELECT .Inside AutoTest, press the Load Script softkey, and highlight and select the required script. (Fig 2)Fig 2: Importing an AutoTest script from floppy disk Before running the script, you can use the On Error softkey to set how AutoTest behaves if a test fails -it can (a) Pause (i.e. the oper-ator decides whether the run should continue or halt), (b) Abort (the run halts regardless), or (c) Ignore (the run, if at all possible,continue). Pause is most appropriate when the UUT is being test-ed by a skilled technician; Ignore is most appropriate for simple pre-screening applications.The screen shows the progress of the test run and any operator action is prompted. (Fig 3)Fig 3: Registration test -operator prompted to turn on the UUTStoring resultsThe results of a test run can be saved to the test set's results directory. When the test has ended, select Results / Store, and enter a filename. Results files can be exported to USB memory or floppy disk via UTILS / File Management / AutoTest / Results .On a PC they can be read by Microsoft ®WordPad orWord. If read by Microsoft ®Notepad, the line terminators used by the 3901make the text confusing to read.Results files can also be imported to the test set from USB mem-ory or floppy disk via UTILS / File Ma na gement / AutoTest /Results , and displayed in AutoTest via Results / Recall.PROGRAMMINGS c r i p t e l e m e n t sAs illustrated in Fig 4, an AutoTest script is made up of the com-mands that allow:•the appropriate system to be loaded into AutoTest (more on this later),•system parameters to be set up,•functional and parametric testing against programmable lim-its.Although most scripts will follow a simple beginning-to-end sequence, the language allows for looping around and, if required, for using different parmeter values in each pass. For example:repeat 4set_rf_gen_level {-70} {-80} {-90} {-100}test_power_level_avg endtests the power level from the UUT at four sig gen levels: -70, -80,-90 and -100 dBm.Bit Error Rate testingSince AutoTest is restricted to the TETRA MS system (and not TETRA MS T1), bit error rate (BER) testing in AutoTest requires the use of TETRA Test (TT) Mode. Currently however, not all mobiles support TT Mode. When using TT Mode, the modified form of AutoTest's registration command:test_registration test_modeshould be employed. With this, once the mobile has registered,the 3901will automatically confirm TT operation.When in TT Mode, you can test bit error rate using commands such as:test_rx_meas_ber -112.0 class0 class1 class2 test_rx_meas_rber -112.0 mer class0 class1Loading a system into AutoTestFor it to operate, the 3900 test set must be loaded with a system such as TETRA MS, TETRA BS T1, etc. As can be seen from the CONFIG / Systems menu, AutoTest itself is classed as one of those systems. H owever, when you load the AutoTest system, AutoTest itself does not have a system loaded into it.The AutoTest command for loading TETRA MS has three versions:system "TETRA MS" defaultsystem "TETRA MS"system "TETRA MS" manualand each has its own properties.1. If the script usessystem "TETRA MS" defaultthen, every time the script is run, TETRA MS is loaded and all its parameters are automatically set to the AutoTest Default Values listed in the 3900 Operating Manual, Chapter22.2.If the script usessystem "TETRA MS"then:•on the first run, AutoTest loads TETRA MS and all its parame-ters are automatically set to the AutoTest Default Values.•on subsequent runs, AutoTest will not load TETRA MS and the script will start with all its parameters set as they currently stand (i.e. however they were left after the previous run).3.If the script usessystem "TETRA MS" manualthen, every time the script is run, TETRA MS is loaded and all its parameters are automatically set to the values saved when TETRA MS was last used manually(i.e. outside AutoTest).The significance of the three commands is as follows:1. system "TETRA MS" default is the most straightforward.Knowing that every run will start with all parameters set to known defaults, the writer simply has to include a relatively small number of setup statements to suit the requirements of the Unit Under Test (UUT).Loading a system adds several seconds to the run time. However, if the time penalty of loading TETRA MS on every run is not a critical issue, the relative simplicity of using system "TETRA MS" default can be attractive, to R& D experimenters looking for a quick way of creating automated test sequences. For example code, see Appendix1, Example 1.2. Since the TETRA MS system is loaded only once, usingsystem "TETRA MS"significantly reduces overall run time.However, the script must include statements not only to modi-fy AutoTest defaults to suit the UUT, but also to re-set any parameters that are modified during a run. Fortunately, the additional run time of the extra setup statements is negligible compared with the time saved by loading the TETRA MS sys-tem only once. S S o,i f y o u p l a n t o r u n t h e s a m e s c r i p t t w o o r m o r e t i m e s c o n s e c u t i v e l y,t h e n system "TETRA MS"i s t h e c o r r e c t c h o i c e.See Example 2.3. It should be noticed that scripts using either of the above twosystem commands effectively have all their parameters hard-coded, thus making them specific to the UUT type. The third command, system "TETRA MS" manual, provides for the creation of 'generic' (non UUT-specific) scripts. Such scripts assume the operator has already set the UUT-specific parame-ters (such as frequency plan, traffic channel, country code, net-work code, etc) before switching the test set into AutoTest.Although the number of parameters may be significant, the operator's workload (and the consequent risk of error) can be minimized by setting up the 3900's store-and-recall facility with the parameters for each UUT type.As with system "TETRA MS" default, system "TETRA MS" manual has the time overhead of always loading the TETRA MS system. However, the ability to use a single script on mobiles that are set up for different channels, etc, may have an overriding attraction to, say, a repair organization. SeeExample 3.Fig 4: Example script structureFor the very latest specifications visit Appendix1: Example AutoTest scriptsEach of the following three examples follow the same pattern of testing: the mobile is registered with the 3901test set, a call is placed, a few parameteric tests are carried out, and the call is closed.Examples 1and 2are each dedicated to a particular Channel Plan, Mobile Country Code and Mobile Network Code. It will be necessary to adjust these values to suit the mobile under test. All that is necessary to do is edit the values given in the Setup UUT-SPECIFIC parameters: section.By contrast, Example 3is generic, requiring the operator to set up those parameters manually in the 3901's TETRA MS mode prior to invoking AutoTest. In addition, Example 3illustrates the use of TT Mode to enable BER tests to be made. If the moble in ques-tion does not support TT Mode, then the BER and RBER tests should be removed and the test_registration statement should be modified in line with Examples 1and 2.Soft copies of the latest versions can be found on the 3900 App Notes pages at /tetra/3900scripts.zip.Example 1This example uses s s y s t e m"T E T R A M S"d e f a u l t to guarantee all parameters revert to default values at the start of every test run -but at the cost of running time. It is dedicated to a particular channel, MCC and MNC.Summary CommentType:UUT-specific Hard coded channels, MCC,MNC, etc.Foolproof:Yes Operator has no influence onparameters.Run time:Slow TETRA MS system reloadedon every run.Notes:Script starts with default values on every run.# Simple_800Band_AutoDefaultVals.ats# March 2005# 3900 AUTOTEST script to register a mobile# (in test mode), place a call from the# mobile, measure TX parameters, and close# the call from the testset.# This script assumes the values specified# in 'Setup UUT-SPECIFIC parameters', below.# ########################################### LOAD TETRA MS AND SET UP SYSTEM PARAMETERS # ########################################### Load TETRA MS system, using default# parameters on every run:system "TETRA MS" default# Setup TEST-SPECIFIC parameters:set_registration_timeout 60set_group_attach_wait 1# Setup UUT-SPECIFIC parameters:set_channel_plan "TETRA 805-870 +12.5"set_control_channel 2040set_traffic_channel 2140set_tch_timeslot 3set_MCC 1set_MNC 00001# ########## RUN TESTS# ########## Register mobile:set_rf_gen_level -75.0test_registration# Mobile-originated call:test_mobile_call phone# Tx tests:test_burst_timing_wctest_power_level_avgtest_power_profiletest_freq_error_wctest_vector_error_rms_maxtest_vector_error_peak_maxtest_residual_carrier_max# Close call from test set:test_testset_clearExample 2This example uses s s y s t e m"T E T R A M S"to minimize overall run time. As in Example 1, this script is dedicated to a particular chan-nel, MCC and MNC.Summary CommentType:UUT-specific Hard coded channels, MCC,MNC, etc.Foolproof:Yes Operator has no influence onparameters.Run time:Fast TETRA MS system loadedonly on first run after loadingthe script.Notes:Script starts with default values on first run.Script writer has to reset only those parametersthat change during a run.# Simple_800Band_NoDefaultVals.ats# March 2005# 3900 AUTOTEST script to register a mobile, # place a call from the mobile, measure TX# parameters, and close the call from the# testset.# This script assumes the values specified# in 'Setup UUT-SPECIFIC parameters', below.# ########################################### # LOAD TETRA MS AND SET UP SYSTEM PARAMETERS: # ########################################### # If this is the first run since loading this # script, then load TETRA MS using default# parameters:system "TETRA MS"# Restore any parameters that are altered# during the test run:set_rf_gen_level -75.0# Setup TEST-SPECIFIC parameters:set_registration_timeout 60set_group_attach_wait 1# Setup UUT-SPECIFIC parameters:set_channel_plan "TETRA 805-870 +12.5"set_control_channel 2040set_traffic_channel 2050set_tch_timeslot 3set_MCC 400set_MNC 3# ########### RUN TESTS:# ########### Register mobile:test_registration# Mobile-originated call:test_mobile_call phone# Tx tests:test_burst_timing_wctest_power_level_avgtest_power_profiletest_freq_error_wctest_vector_error_rms_maxtest_vector_error_peak_maxtest_residual_carrier_max# Close call from test set:test_testset_clearExample 3The previous examples, by setting-up all parameters prior to test-ing the UUT, are dedicated to testing on a particular channel, MCC, MNC, etc. By contrast, this example uses s s y s t e m"T E T R A M S"M a n u a l as a means of generating a generic script. However, it assumes that the operator manually sets up the test set appro-priate to this UUT before selecting AutoTest and running the script.Summary CommentType:Generic Operator sets parameterswith normal 3900 manualscreens immediately before Foolproof:No selecting AutoTest.Run time:Slow TETRA MS system reloadedon every run.Notes:Script starts with (operator pre-set) values onevery run.# Simple_Generic_TTMode_ManualVals.ats# March 2005# 3900 AUTOTEST script to register a mobile# (in test mode), place a call from the# mobile, measure TX and Rx parameters, and# close the call from the testset.# This script assumes:# 1. The UUT supports TT mode.# 2. The operator manually sets-up the test# set appropriate to the UUT before# selecting AutoTest, loading this script # and running it.# ########################################### # LOAD TETRA MS AND SET UP SYSTEM PARAMETERS: # ########################################### # On every run, load TETRA MS system using# values as saved when TETRA MS was last used # manually (i.e. outside AutoTest):system "TETRA MS" manual# Setup TEST-SPECIFIC parameters:set_registration_timeout 60set_group_attach_wait 1# ########### RUN TESTS:# ########### Register mobile, confirm in TT mode:test_registration test_mode# Mobile-originated call:test_mobile_call phone# Tx tests:test_burst_timing_wctest_power_level_avgtest_power_profiletest_freq_error_wctest_vector_error_rms_maxtest_vector_error_peak_maxtest_residual_carrier_max# Rx tests:test_rx_meas_ber -112.0 class0 class1 class2 test_rx_meas_rber -112.0 mer class0 class1# Close call from test set:test_testset_clearFor the very latest specifications visit Appendix2: Code to set TETRA MS AutoTest DefaultsThe following code sets all TETRA MS AutoTest parameters to the AutoTest Default values listed in Chapter22of the 3900 Operating Manual. By pasting all or part of this code into your test scripts, and selectively adjusting values, you can minimize the effort involved in the setting up of test parameters. Soft copy of the latest version can be found on the 3900 App Notes pages at /tetra/3900scripts.zip.Commands are grouped in functional blocks, resulting in some (such as set_ptt_timeout and set_traffic_channel) appearing more than once.For the purposes of this application note, (+++) indicates that a long command has been wrapped around. In reality, AutoTest commands cannot be continued onto another line.# Name: 3900_TETRA_MS_All_Defaults.txt# Date: May 2005# The following code sets all TETRA MS# AutoTest parameters to the AutoTestDefault# values listed in Chapter 22 of the 3900# Operating Manual.# It is not a complete test script.However,# it is intended as a typing shortcut, to be # pasted, all or in part, into users' own# scripts with values altered as required.# ############################### Setting default parameters ...# ############################### Default GENERAL parameters:set_rf_ana_control_mode expectedset_rf_ana_port trset_rf_ana_level_offset_enable offset_rf_ana_level_offset_value 0.0set_rf_ana_expected_level +30.0set_rf_gen_level -75.0set_rf_gen_port trset_rf_gen_level_offset_enable offset_rf_gen_level_offset_value 0.0set_timing_offset_enable offset_timing_offset_value 0.0# Default IN CALL parameters:set_idle_channel message facchset_rf_ana_control_mode open# Default POWER LEVEL test parameters:set_power_class 4set_power_class_usage reportedset_power_level_limits +2.0 -2.0 +2.5 -2.5set_power_samples 20set_ptt_timeout 20# Default POWER PROFILE test parameters:set_power_profile_limits -70.0 -36.0 +6.0+3.0set_ptt_timeout 20# Default BURST TIMING test parameters:set_burst_timing_limit 0.25set_burst_timing_samples 20set_ptt_timeout 20# Default FREQUENCY ERROR test parameters: set_freq_error_limit 100set_freq_error_samples 20set_ptt_timeout 20# Default VECTOR ERROR RMS test parameters: set_vector_error_rms_limit 10.0set_vector_error_rms_samples 20set_ptt_timeout 20# Default VECTOR ERROR PEAK test parameters: set_vector_error_peak_limit 30.0set_vector_error_peak_samples 20set_ptt_timeout 20# Default RESIDUAL CARRIER test parameters: set_residual_carrier_limit 5.0set_residual_carrier_samples 20set_ptt_timeout 20# Default RX MEAS - BER test parameters:set_BER_class0_limits 4.27 4.88 4.27set_BER_class0_samples 15000set_BER_class1_limits 0.23 0.23 0.23set_BER_class1_samples 15000set_BER_class2_limits 0.23 0.23 0.23set_BER_class2_samples 15000set_rx_class Aset_rx_class_usage reportedset_level_change_wait 2# Default RX MEAS - RBER test parameters:set_MER_limits 0.045 0.045 0.045set_MER_samples 300set_RBER_class0_limits 4.27 4.88 4.27set_RBER_class0_samples 15000set_RBER_class1_limits 0.23 0.23 0.23set_RBER_class1_samples 15000set_rx_class Aset_rx_class_usage reportedset_level_change_wait 2# Default REGISTRATION test parameters:set_access_param -45set_base_advanced_link not_supportedset_base_air_interface_encryption not_avail-ableset_base_circuit_mode_data_service(+++) not_supportedset_base_migration supportedset_base_minimum_mode_service never_usedset_base_power_off_deregistration required set_base_power_on_registration requiredset_base_priority_cell yesset_base_reserved not_availableset_base_system_wide_services normal_modeset_base_tetra_packet_data_service(+++) not_availableset_base_tetra_voice_service supportedset_BCC 01set_channel_plan "TETRA 380-400 +12.5"set_control_channel 3600set_group_attach_wait 25set_GSSI 1set_GSSI_usage reportedset_LA 00001set_max_tx_level 30set_MCC 001set_min_rx_level_access -125set_MNC 00001set_registration_timeout 30set_SSI 00000001set_SSI_usage reported# Default PLACE CALLS FROM TEST SET# test parameters:set_emergency_call_params individual simplex(+++) direct 742200set_group_call_params 00 742200set_phone_call_params 00 "01438742200" incset_place_call_timeout 20set_place_call_typecheck yesset_private_call_params simplex hook 00742200set_tch_timeslot 3set_traffic_channel 3700set_user_call_params individual duplex hook00(+++) 16777186 "742200" inc# Default PLACE CALLS FROM MOBILE test# parameters:set_place_call_timeout 20set_place_call_typecheck yesset_tch_timeslot 3set_traffic_channel 3700# Default CALL CLEARDOWN FROM TEST SET test# parameters:# ... there are no parameters to set# Default CALL CLEARDOWN FROM MOBILE test# parameters:set_clear_call_timeout 20# Default DEREGISTRATION test parameters:set_deregistration_timeout 20# Default SPEECH QUALITY / TONE / SILENCE# test parameters:set_audio_test_timeout 20set_ptt_timeout 20# ######################################### ... finished setting default parameters.# ########################################For the very latest specifications visit 。

FILTRATION & PROCESSFILTRATION & PROCESS5730 NORTH GLEN PARK ROAD, MILWAUKEE, WI 53209P: 262.238.4400 | | CUSTOMER CARE: 800.279.9404 | tech-support @All Pentair trademarks and logos are owned by Pentair, Inc. or its affiliates. All other registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services. Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.40742 REV D JL14 © 2013 Pentair Residential Filtration, LLC. All Rights Reserved.VALVE SPECIFICATIONS Valve Material Lead-free brass*Inlet/Outlet 3" NPTF/BSPF Cycles 3 or 5FLOW RATES (50 PSI INLET) – VALVE ALONEContinuous250 GPM (56.8 m 3/h) 15 psi dropPeak325 GPM (73.8 m 3/h)25 psi dropCv 65flow at 1 psi dropMax. Backwash100 GPM (22.7 m 3/h)25 psi dropREGENERATIONDownflow/UpflowBothAdjustable Cycles YesTime Available Electromechanical: 0 - 164 min/regeneration NXT: 0 - 240 min/cycle XT:0 - 240 min/cycleMETER INFORMATIONMeter Accuracy 3" Paddle: 7 - 300 GPM ± 5% (1.6 - 68 m 3/h)Meter Capacity Range 3" Standard: 3,750 - 63,750 gal (14 - 240 m 3) 3" Extended: 18,750 - 318,750 gal (71 - 1,200 m 3) NXT: 1 - 9,900,000 gal (0 - 37,476 m 3) XT: 1,000 - 9,900,000 gal (3.8 - 37,476 m 3)DIMENSIONSDistributor Pilot 3" O.D. (90 mm)Drain Line 2" NPTF Brine Valve 1800: 1"Injector System 1800Mounting BaseT op: 6" – 8 threaded, 6" flanged or welded flangeHeight from Top of Tank 15" (381 mm)Riser Tube Diameter 3" (76 mm)Riser Height Flush with top of tankTYPICAL APPLICATIONSWater Softener 24 - 63" diameter Filter 24 - 42" diameter based on 10 GPM/ft 2ADDITIONAL INFORMATIONElectrical Rating 24/110/220V;50/60 Hz Estimated Shipping Weight Time Clock: 93 lbs Metered Valve: 115 lbs Pressure Hydrostatic:300 psi(20 bar) W orking:20 - 125 psi(1.4 - 8.5 bar)Temperature Cold Water Valve:34 - 110°F (1 - 43°C)* A s defined in the U.S. EPA Safe Drinking Water Act; the product also meets California Proposition 65 Standards for lead-free brass.。